ACARD ARS-2030PC USB Card Reader to 3 IDE ODD Copy
Contents
1. After the image file is deleted LCD will show the results as follows Partition A Image is deleted 5 2 9 3 Image Info This function is to show the basic information of an image file stored in a particular partition First select the function by pressing W 9 03 Image PA Image Info Press ENT and LCD will show the information of the image file as follows Img Type DVD R Capacity 4213 4MB 5 2 9 4 Compare Image This function is to compare the contents of the source DVD and those of the image file in the partition First select the function by pressing W 9 04 Image PA Compare Image Press ENT and LCD will show the information of the image file as follows Com A DVD 0 4213 4MB 7 30 When comparison comes to an end LCD will show the results as follows Compare OK 1 Fail 0 Diff O Press ENT to see the details of source as shown below Src 01 SUPER MUL Total 4213 4MB 31 ARS 2030PC Manual Press ENT to see the details of target If the comparison is identical LCD will show the message as follows Tgt 00 HDD P A Identical If comparison fails LCD will show the failure By pressing ENT twice LCD will show that the contents of source and those of target do not match as follows Tgt 00 HDD P A TOC not match 5 2 9 5 Select Image This function is to select a partition in the har2. 11 Setup 12 Model Select 13 Adv Setup 22 The ninth function has 8 sub functions 9 01 Load 9 02 Delete Image 9 03 Image Info 9 Image 9 04 Compare Image 9 05 Select Image 9 06 Image Src Drive 9 07 ImageFormat Info The tenth function has 4 sub functions 9 08 Edit 10 01 CD to CD Edit 10 Edit Track 10 02 CD to HDD Edit 10 03 Play Audio Track 10 04 Close Session 23 ARS 2030PC Manual ARS 2030PC Manual The eleventh function has 21 sub functions 11 01 Language 11 02 CD Burn Speed 11 03 DVD Burn Speed 11 04 Read Speed 11 05 Auto Start Drive 11 06 Startup Menu 11 07 Auto Verify 11 08 Auto Compare 11 09 Auto Prescan 11 Setup 11 10 Eject Disc 11 11 Burn On the Fly 11 12 Burn Mode 11 13 Display Time 11 14 Button Sound 11 15 Device Info 11 16 System Info 11 17 Quick Erase 11 18 Full Erase 11 19 Auto Close Tray 11 20 Quick Compare 11 21 Audio Burn Speed 24 The thirteenth function has 18 sub functions 13 01 UnderRun Protect 13 02 Ove
3. 5 2 13 3 Read Error Skip Now press ESC and Y to enter the following figure Read Error Skip is to ignore any error that occurs during copying Under normal circumstances when an error occurs during copying a message will appear on LCD Yet you can use Read Error Skip to copy some defective medias 13 03 Adv Setup Read Error Skip 49 ARS 2030PC Manual Press ENT to enter the following figure The default is Off Press W to select On Read Error Skip Off 5 2 13 4 Format HDD Now press ESC and Y to enter the following figure Format HDD is to partition the hard disk But before formatting all data on the hard disk will be deleted 13 04 Adv Setup Format HDD If your copy controller doesn t connect with a hard disk LCD will show the message as follows No Valid HDD Select HDD First 5 2 13 5 Verify HDD Now press ESC to return to Function 13 and then select part 5 Verify HDD as the following figure shows Verify HDD is to verify if the hard disk or any of its partitions can work well 13 05 Adv Setup Verify HDD Press ENT to enter the next figure Use A W to confirm Disk or Parti Verify Disk or Paration Disk Press ENT to verify After verification LCD will show the results as follows Overburn Off 5 2 13 6 Burn in Now press ESC and Y to enter the following figure Burn in is to simulate the copying progress many times
4. After selecting please use A to move to the End menu as shown below Select Track End 1Trk04 25 Press ENT to finish the CD editing and use s t to confirm Yes or No End edit disc and burn Yes Then the track as an image file will be loaded into HDD LCD will show the loading information as follows Load P0 24X Edit 2110 gt 2 2 When loading comes to an end LCD will show the message as follows Image load OK The system will ask if you want to keep editing This time please use W to confirm No as shown below Continue edit next Disc No Then the system will ask if you want to burn from HDD into CD R RW or move into a partition Please use A to confirm Burn as shown below Burn or Move to partition Burn After pressing A LCD will show the copying information as follows Copy P0 24X 0 1 2 Trk03 25 38 ARS 2030PC Manual When burning finishes LCD will show the results as follows Burn Complete OK 03 Now press ESC to enter the following figure And press W to move the data from HDD template into a certain partition Burn or Move to partition Move After pressing W you need to select a partition into which the data will be moved Suppose we select A as shown below Select Partition A After pressing ENT LCD will show the moving information as follows Movi
5. Now press ESC and Y to enter the following figure Auto Verify is to verify automatically if the target DVDs can be read after copying 42 ARS 2030PC Manual 11 07 Setup Auto Verify Press ENT to enter the following figure The default is Off Press W to select On Auto Verify Off 5 2 11 8 Auto Compare Now press ESC and Y to enter the following figure Auto Compare is to compare automatically the source DVD and the target DVDs after copying 11 08 Setup Auto Compare Press ENT to enter the following figure The default is Off Press W to select On Auto Compare Off 5 2 11 9 Auto Prescan Now press ESC and Y to enter the following figure Auto Prescan is to scan automatically if the source DVD can be read correctly and by the way to test the reading speed 11 09 Setup Auto Prescan Press ENT to enter the following figure The default is Off Press W to select On Auto Prescan Off 5 2 11 10 Eject Disc Now press ESC and Y to enter the following figure Eject Disc provides three choices They are Eject Good Only Eject All Disc and Do Not Eject Eject Good Only means that the DVDs will eject automatically only when they are copied successfully Eject All Disc means that the DVDs will eject automatically whether they are copied successfully or not Do Not Eject means that you need to eject the DVDs manually when copying finishes 11 10
6. When closing finishes LCD will show the results as follows Closing Complete OK 3 Fail 0 5 2 11 Setup Function 11 Setup lets you change the default settings Once you change a setting remember to press ENT to save it However it is suggested to use the defaults for the optimal operation This function includes 21 subfunctions Language CD Burn Speed DVD Burn Speed Read Speed Auto Start Drive Startup Menu Auto Verify Auto Compare Auto Prescan Eject Disc Burn On The Fly Burn Mode Display Time Button Sound Device Info System Info Quick Erase Full Erase Auto Close Tray Quick Compare and Audio Burn Speed Refer to page 14 for the menu 40 ARS 2030PC Manual Select function 11 11 Setup 5 2 11 1 Lanuage Now press ENT and you will enter the following figure The function Language lets you select a language in which messages can be shown on LCD 11 01 Setup Language Press ENT to enter the following figure The default is English Spanish Japanese Traditional Chinese and Simplified Chinese are made to order Lanuage English 5 2 11 2 CD Burn Speed Now press ESC and Y to enter the following figure This function lets you control the burning speed of CD writers 11 02 Setup CD Burn Speed Press ENT to enter the following figure The default is auto CD Burn Speed Auto 5 2 11 3 DVD Burn Speed Now press ESC and Y to e
7. 60 ARS 2030PC Manual Technical Support Form Email address support acard com Website http www acard com Model Name ARS 2030PC Firmware version System Configuration Card Reader model Motherboard System model SCSI host adapter chip brand A model SCSI host BIOS version Other VO card Operating System SATA HDD brand amp model SATA HDD capacity SATA HDD firmware Problem description 61
8. Setup Eject Disc 43 ARS 2030PC Manual Press ENT to enter the following figure The default is Eject Good Only Press W to select Eject All Disc or Do Not Eject Eject Disc Eject Good Only 5 2 11 11 Burn On The Fly Now press ESC and Y to enter the following figure Burn On The Fly lets you control the copying methods When the setting is On the data will be copied directly from the source DVD to the target DVDs When the setting is Off the data will be loaded into a partition of HDD first and hence copying will be done 11 11 Setup Burn On The Fly Press ENT to enter the following figure The default is On Press W to select Off Burn On The Fly On 5 2 11 12 Burn Mode Now press ESC to return to Function 11 and then select part 12 Burn Mode as the following figure shows Burn Mode lets you control the burning modes There are two modes DAO Disc At Once and TAO Track At Once They only supports CD If the DVD writer doesn t support the mode you have selected the copy controller will automatically switch to another mode 11 12 Setup Burn Mode Press ENT to enter the next figure The default is DAO Press W to select TAO Burn Mode DAO 5 2 11 13 Display Time Now press ESC and Y to enter the following figure Display Time is to show the copying time 11 13 Setup Display Time Press ENT to enter the next figure The def
9. brief operational procedures for the systems with and without an internal hard drive 10 ARS 2030PC Manual 3 3 1 With an Internal Hard Drive When a 3 5 inch SATA hard drive is connected to the ARS 2030PC please follow the operational procedures below m You can check if the hard drive is detected by the ARS 2030PC through the device information function list no 11 15 If a hard drive is detected and correctly recognized by the ARS 2030PC the CHO in the device information will be HDD Before any operation the hard drive has to be formatted You can format the hard drive through the 13 04 function m Set the hard drive as the source through the eighth function Select Source The default value is source Choose a partition for data storage through the ninth function Image m f the selected partition is empty insert a DVD CD to the DVD ROM and choose the 9 01 function Load Press ENT to back up the DVD CD to the selected partition Different data should be stored in different partitions Exit the menu by pressing ESC and switch to the first function Copy by pressing A or V Insert a blank DVD CD into the DVD burner and press ENT to start copying Upon completion of data copying the successfully duplicated DVD CD will be ejected automatically The default setting is automatic ejection and it can be changed The failed DVD CD will be held in the DVD burner The default setting keeps the failed DVD CD
10. 8 2 2 Complete Backup SISTEMA er eed as cane dee vers 8 2 3 Backup System Without DVD CD Bumers nnn 8 2 4 Installing the AH 2020PC EE 9 Chapter 3 Basic OPeratiONS sccaceeenne2seicseacvntsecetessvonssavdeas aboneadeedasnenng ste ueleqeusteadeaesans 10 3 The Keypad and Ee E 10 3 2 Installing the All in One Card Reader for Flash Copier Mode 10 3 3 Installing the hard drive for DVD Copier Mode 10 3 3 1 With an Internal Hard Drive 11 3 3 2 Without an Internal Hard De 11 Chapter 4 The PCB EE stc ardoz 12 Chapter 5 Operational Funchons EE 13 5 1 Flash Eeer 13 5 1 1 Mem Card OY oia 14 E O ege EM 15 513 COMpar a NI RO 15 5 1 4 Mem Card A A ect eee ees 16 E EE RE e EE 16 5 1 6 Restore Dalias ade 17 deL Erase DI idas 17 5 1 8 Model A O 18 O eter a ee eee ee E Eee emt ee Ae eee EH 19 Deel AEA AAA E E EEE ETE 19 5 1 92 DVD BUM Speed russia aa 19 Br E Eject RI 20 SS Le EE 20 EE Eeer 20 5 RIG Systemi MIO EE 21 Decke Update FirMmWa erica oc 21 euni EH 21 AA eebe eg 22 5 2 1 COPY A O O A eee 26 NEE 26 5 24 NONY etse EE 27 A E a E saad ei nee ee atc 28 PP E E E E E E E 28 527 DISCO rr Sn ds 29 SA tease eerie a rem nena ees ete aa aaa a aa 29 A Ia EE O EE 30 a E E e EE 30 AA A A A A Senne Ea EE 30 E Image O GE EN 5 2 9 4 Compare nn le E EN A fond tacdunaslenatenestd Oa eea a E Aa E E denne EErEE 32 5 2300 Image Sre DIVER a 32 5 2 9 7 Image Format IO canaria 33 EE O e tere 33 5 2 10 Edit Track for
11. Copying DVD 0 4213 4MB 7 30 When copying is in progress MB and time will decrease while the percentage of completion will increase MB means the size of data that you want to copy When copying comes to an end LCD will show the results as follows The passed DVDs will eject automatically 1 Copy OK 03 5 2 2 Test Function 2 Test is simulation of duplication function no data will be written to the media CD R DVD R Select function 2 Put a source DVD into DVD ROM and blank DVDs into the DVD writers Only a DVD R disc supports this function 2 Test Press ENT to start simulation If you use DVD rewriteable discs that contain data the old data will be quickly erased before simulation as shown below Erasing disc 26 ARS 2030PC Manual LCD will show the testing information as follows Testing DVD 0 4213 4MB 7 30 When the test comes to an end LCD will show the results as follows 2 Test OK 03 Stopping the test halfway does not affect the DVDs but if the DVD rewriteable discs contain important data they may be destroyed 5 2 3 Test amp Copy Function 3 Test amp Copy is to test first and then copy actually Select function 3 Put a source DVD into DVD ROM and blank DVDs into the DVD writers 3 Test amp Copy Press ENT to start simulation LCD will show the testing information as follows Testing DVD
12. ENT and the system is now in the Flash Copier Mode The following menu will be shown on the LCD 1 Mem Card Copy 48 ARS 2030PC Manual 5 2 13 Adv Setup Function 13 Adv Setup lets you change the system configuration This function includes 20 subfunctions UnderRun Protect Overburn Read Error Skip Format HDD Verify HDD Burn in Update Firmware Compare Firmware H W Diagnostic Load Default CD G ISRC 8 MCN USB Option CD TEXT Password Disc Counter Auto Save Image Update Drive F W F1 Hot Key Setting and F2 Hot Key Setting Refer to page 17 for the menu Now press ESC to return to Function 12 Then press ESC for 2 seconds to enter Function 13 as the following figure shows 13 Adv Setup 5 2 13 1 UnderRun Protect Now if you press ESC you can enter Function 12 as the following figure shows 13 01 Adv Setup UnderRun Protect UnderRun Protect lets you control On and Off of Buffer Under Run Protection Press ENT to enter the following figure The default is On Press W to select Off UnderRun Protect On 5 2 13 2 Overburn Now press ESC and Y to enter the following figure Overburn lets you decide whether to copy beyond the limit of the media or not 13 02 Adv Setup Overburn Press ENT to enter the following figure The default is Off Press W to select On Overburn may cause a DVD writer to be damaged and data incomplete Overburn Off
13. HDD Edit 36 ARS 2030PC Manual Now press ENT and you will enter the following figure Here 1 10 means the number one of the 10 tracks and 03 25 means the playing time Select Track 1 10 03 25 Suppose we decide to select the first track then press ENT A will appear beside 1 10 as shown below But pressing ENT again may cancel the selection Select Track 1 10 03 25 After selecting please use A to move to the End menu as shown below Select Track End 1Trk03 25 Press ENT to finish the CD editing and use A Y to confirm Yes or No End edit disc and burn Yes Then the track as an image file will be loaded into HDD LCD will show the loading information as follows Load P0 24X Edit 1 10 gt 1 1 When loading comes to an end LCD will show the message as follows Image load OK The system will ask if you want to keep editing Please use A W to confirm Yes or No as shown below Continue edit next Disc Yes If you want to keep editing the current source CD will eject auctomatically and the system will ask you to insert another new CD as shown below Insert next disc 37 ARS 2030PC Manual After inserting the new CD press ENT to edit as before Suppose we select the second track then press ENT A will appear beside 2 10 as shown below Select Track 2 10 04 25
14. Installation Before installing the ARS 2030PC please note that this product comes in three kinds of packages Storage Controller Only Complete Backup System and Backup System Without DVD CD Burners 2 1 Storage Controller Only Open the package and check the product for any damage Prepare a DVD CD drive Prepare 3 DVD CD burners and a flash memory card Flash Copier Mode Prepare 3 DVD CD burners DVD Copier Mode m Prepare one 3 5 inch SATA hard drive optional 2 2 Complete Backup System Open the package and check the product for any damage m Prepare one 3 5 inch SATA hard drive optional Prepare a power supply with enough watt ratings 2 3 Backup System Without DVD CD Burners Open the package and check the product for any damage Prepare 3 DVD CD burners and a flash memory card Flash Copier Mode Prepare 3 DVD CD burners DVD Copier Mode m Prepare one 3 5 inch SATA hard drive optional Ensure the power supply has enough watt ratings ARS 2030PC Manual 2 4 Installing the ARS 2030PC The following block diagram and pictures show the connection of the ARS 2030PC to an all in one card reader a SATA hard drive and 3 DVD burners Under the Flash Copier Mode the system can take MS CF MD SD MMC SM and USB flash media as the source of data copying Note For data copying only one type of media can
15. The time can be from 1 to 1000 After each cycle of simulation the medias on the DVD writers will eject automatically and recede for the next bout of simulation 12 06 Adv Setup Burn in 50 ARS 2030PC Manual Press ENT to enter the next figure Test is simply a simulation Burn in Test Press ENT and use A Y to select the time of simulation such as 1 2 3 1000 or Run Continuous The figure below shows Run Continuous Sel burn in num Run Continous Press ESC ENT Y to select Erase A Copy as the following figure shows Erase amp Copy is to erase and write repeatedly It is only for media rewriteable discs Burn in Erase amp Copy Press ENT and use A Y to select the time of simulation such as 1 2 3 1000 or Run Continuous The figure below shows Run Continuous Sel burn in num Run Continous 5 2 13 7 Update Firmware Now press ESC and Y to enter the following figure Update Firmware is to update firmware to the latest version But you should get the version first 13 07 Adv Setup Update Firmware You can get the newest firmware version from ACARD by e mail or download it directly from the web site http www acard com Then unzip the file of zip and copy it into a CD RW If the file is bin you don t need to unzip After placing the media into the DVD ROM press ENT The system will begin searching the new firmware and show the me
16. and choose 10 seconds here then one writer s tray or all seven writers trays will be closed in 10 seconds after copying finishes 5 2 11 20 Quick Compare Now press ESC and Y to enter the following figure Quick Compare is related to function 5 Compare It lets you set a certain byte When the error of a target DVD is beyond the set byte the comparison between the source DVD and the target DVD will stop Yet the comparison of the other 6 target DVDs will continue 11 20 Setup Quick Compare 47 ARS 2030PC Manual Press ENT to see the following figure The default is Off but you can press W to choose a certain byte like 1 Byte 1 KB 10 KB 100KB 1 MB etc Quick Compare Off 5 2 11 21 Audio Burn Speed Now press ESC and Y to enter the following figure Audio Burn Speed lets you control the burning speed of audio CDs 11 21 Setup Audio Burn Speed Press ENT to see the following figure The default is auto but there are maximum 40X 32X 24X 20X etc for choice Audio Burn Speed Auto 5 2 12 Model Select The function Model Select sets the operational mode of the copy controller The 2030PC has two operational modes DVD Copier and Flash Copier The default mode is Flash Copier 12 Model Select Press ENT to enter the following menu Choose Yes to switch to the Flash Copier mode Change Mode to Flash Copier Yes Press
17. menu ALL date will be Lost erase Yes Press ENT to enter the following menu and start Quick Erase Erasing disc 00 12 Quick Upon completion of data erasing the following message will be displayed on the LCD Quick Erase OK 03 FAIL 00 5 1 8 Model Select The function Model Select sets the operational mode of the copy controller The 2030PC has two operational modes DVD Copier and Flash Copier The default mode is Flash Copier 8 Model Select Press ENT to enter the following menu Choose Yes to switch to the DVD Copier mode Change Mode to DVD Copier Yes Press ENT and the system is now in the DVD Copier Mode The following menu will be shown on the LCD 1 Copy 18 ARS 2030PC Manual 5 1 9 Setup The Setup function changes the default settings Once the settings are changed they have to be saved by pressing ENT However the default settings are recommended for the best performances This function has 8 sub functions including Language DVD Burn Speed Eject Disc Button Sound Device Info System Info Update Firmware Compare Firmware Please refer to the figure on Page 13 for detailed information Choose the ninth function Setup as shown in the following figure 9 Setup 5 1 9 1 Language Now press ENT to enter the following menu This function can specify the language of the LCD messag
18. use function 9 Image to load the data into the chosen partition first 5 2 9 Image Function 9 Image is valid only when you have installed a hard disk This function includes 7 subfunctions Load Delete Image Image Info Compare Image Select Image Select Src Drive and Image Format Info The loaded data is called an image file Refer to page 24 for the menu Select function 9 9 Image 5 2 9 1 Load Now press ENT and you will enter the following figure Here the function Load is to let you load data from DVD ROM or any one of the DVD writers into the current partition of the hard disk DAT means partition A 9 01 Image PA Load Press ENT to load LCD will show the loading information as follows Load A DVD 0 4213 4MB 7 30 After the image file is successfully loaded LCD will show the results as follows Image load OK If there is an image file existing in the current partition the system will ask you whether to overwrite it or not Please use A Y to confirm Yes or No Image Exists Overwrite Yes 5 2 9 2 Delete Image If you want to delete an image file stored in a particular partition you can use the function Delete Image to do so First select the function by pressing W 9 02 Image PA Delete Image 30 ARS 2030PC Manual The system will ask if you are sure to delete Use A W to confirm Yes or No Delete Image Yes A Untitled
19. 0 4213 4MB 7 30 When the test finishes actual copying will begin as shown below Copying DVD 0 4213 4MB 7 30 When the whole process finishes LCD will show the results as follows 3 Test amp Copy OK 03 Note that those discs that have passed the test will be copied right away while those that haven t won t be 5 2 4 Verify Function 4 Verify is to verify the data burned on CD DVDs Select function 4 4 Verify 27 ARS 2030PC Manual Press ENT to verify LCD will show the verification information as follows Verify DVD 0 4213 4MB 7 30 When verification comes to an end LCD will show the results as follows 4 Verify OK 03 5 2 5 Compare Function 5 Compare is to make a comparison between the source DVD and the target DVDs after copying Select function 5 Put the source DVD into DVD ROM and the target DVDs into DVD writers 5 Compare Press ENT to compare LCD will show the comparison information as follows Compare DVD 0 4213 4MB 7 30 When comparison comes to an end LCD will show the results as follows Compare OK 03 Fail 0 Diff 0 Press ENT to see the details of source 1 as shown below Src 02 DVD RW Identical If comparison fails LCD will show the failure By pressing ENT twice LCD will show that the contents of source 1 and those of source 2 do not match as fol
20. 5 Disc Info 6 Restore Card 7 Erase Disc 8 Model Select 9 Setup The ninth function has 8 sub functions 9 01 Language 9 02 DVD Burn Speed 9 03 Eject Disc 9 04 Button Sound 9 Setup 9 05 Device Info 9 06 System Info 9 07 Update firmware 9 08 Compare Firmware 13 ARS 2030PC Manual 5 1 1 Mem Card Copy The Mem Card Copy function copies the data of the source flash media directly to a blank DVD CD Before copying please make certain that the source flash media is inserted into the correct slot on the card reader Check the file size of the flash media and choose a proper DVD or CD When the source has more data than the capacity of the target disc the system automatically splits the data However if the data is an inseparable data block the copying operation will be aborted In this case please use a target disc with larger capacity than the source Choose the first function Copy Insert the source media into the correct slot on the card reader and a blank DVD CD into the DVD burner You may use a rewritable DVD with existing data All the existing data on that rewritable DVD will be erased 1 Mem Card Copy After the system detects the flash media and the target DVD press ENT to start copying The following message will
21. ACARD ARS 2030PC USB Card Reader to 3 IDE ODD Copy Controller User s Manual Version 1 1 Attention Wait over 5 seconds to power on after shutdown to prevent the abnormal operation of the system ACARD ql a y MEL e Copyright 2009 ACARD Technology Corp Release Jun 2009 CE FE Copyright and Trademarks The information of the products in this manual is subject to change without prior notice and does not represent a commitment on the part of the vendor who assumes no liability or responsibility for any errors that appear in this manual ACARD and SCSIDE are the trademarks of ACARD Technology Corp This manual contains materials protected under International Copyright Laws All rights reserved No part of this manual may be reproduced transmitted or transcribed without the expressed written permission of the manufacturer and author of this manual ACARD s ARS 2030PC Copy Controller is used for copying and editing personal audio and video data Violating Copy Right is a criminal act ACARD s Copy Controller only supports legal backup operation ACARD Technology Corp is not responsible for illegal recording Table of Contents Chapter 1 MAUI os ee oe fee a oe 7 A A eee pe ee ene 7 A iaa a E E EEA 7 E a a a ah a S a A E O E AE on teas 7 1 4 System REQUIEM ota 7 Chapter 2 Hardware Installati0N oooooononnoccnncnnconnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnoncnnnonnnnns 8 2 1 Storage Controller Ocotal rd li asis
22. CD press ENT to edit as before Suppose we decide to select the second track then press ENT A will appear beside 2 10 as shown below Select Track 2 10 04 25 After selecting please use A to move to the End menu as shown below Select Track End 1Trk04 25 35 ARS 2030PC Manual Press ENT to finish the CD editing and use A Y to confirm Yes or No End edit disc and burn Yes LCD will show the copying information as follows Copying 24X Edit 2 10 gt 2 2 2 2 means the second track of all tracks we have selected and so far we have selected two tracks from two different CDs When copying comes to an end LCD will show the message as follows Burn Complete OK 03 The system will ask if you want to keep editing Suppose we don t like to continue then press W to confirm No Continue edit next Disc No Now press ENT The system will ask if you want to close all CDs sessions Please use A W to confirm Yes or No as shown below Closing Session Please wait When closing comes to an end LCD will show the message as follows Closing Session OK 03 5 2 10 2 CD to HDD Edit After closing sessions press ESC and Y to enter the following figure Here the function CD to HDD Edit lets you select a track or more from CD ROM and then copy into a certain partition of HDD 10 02 Edit Track CD to
23. Compatible Flash Meditacion A A nes 57 6 4 About DVD ROM DVD Wrterg EEN 57 ee Dieter ad 57 6 6 About DVD Writer Not Hezdable 57 6 7 About High E aurea ja Ria 58 6 8 About Firmware Update 58 6 9 About Function 13 and CGancelaton nana rn nnnn rr 58 Appendix A LCD Messages EE 59 Technical Support FO E aii 61 ACARD WEEE Statement H az WEEE Statement English In order to cope with the increasing waste electrical and electronic equipment reduce the use of landfill and incinerator and prevent the harmful matter of waste equipment from entering the environment the European Union EU has set the Directive on Waste Electrical and Electronic Equipment WEEE asking manufacturers to collect recycle and treat waste electrical and electronic equipment properly Member nations already established their free of charge recycle systems of WEEE before August 13 2005 Accordingly ACARD has to be responsible for recycling all products exported to Germany You can return your ACARD product that needs recycling to a local collector WEEE Erkl rung Mit dem Ziel die steigende Menge elektrischer und elektronischer Altgerate zu bewaltigen ohne hierzu unn tig M lldeponien und Verbrennungsanlagen zu belasten und um die Verschmutzung der Umwelt durch freiwerdende Stoffe aus den Altgeraten zu vermeiden hat die Europaische Union EU die Richtlinie Uber Elektro und Elektronik Altgerate erlassen Die Richtlinie verpflichtet Hersteller elektrische und elektro
24. E only EE 34 S IIA E 34 2 102 CD10 ADO Edit zire ia e eds os 36 9 2 1 0 9 Play Audio Wee EE 39 A IA deed eeben gees 40 EN RE 40 ER ER Le e E 41 929 12 CO BUM SPCC DEE 41 5 2 11 3 DVD Burn SCC A EE 41 5 2114 Redd A eedudesncnieecsancns 42 525115 AUTO Start DAVE sr a alas 42 De Sano Mesa A 42 A PAULO TIL E 42 5 2 11 8 Auto E OM ANS ts coe EE 43 S2 OAU D E 43 UE eege 43 E A eee eens 44 5 2 11 12 Burn Te te 44 zio Display Mesta ide as 44 5 2 1 114 BUON SOU AS eee AA 45 nh PIESA DINIE te DEE 45 5 2 11 16 System IO tna ae eels ceda 45 D2 H fa Er QUICK A EE a E A Eae e e eae ae 46 Salle FU ee ds dd e 46 Dee UA A E 47 52 11 20 Quick Compare ira 47 5 2 11 21 Audio BUS A Ss 48 E ele EE 48 EE 49 5 2 13 1 UnderRun Prod ti 49 52132 e a ee ea dd e esoo Do od 49 5 2 13 39 RCAC Error SKID E 49 A Format AA es orate as ena on Ce ote oe ne eee cate a 50 E ES HDD EE 50 92120 BUM Ee DEE 50 5 2137 Upa te FIMWAROcacuseperenacuncalaccadoinlooriacocaenioiado cion egenen 51 02 19 90 Compare EHNEN eege eege 52 AAA A es tiem tan Steet 52 9219 10 Load Default scr aia 52 EE E ah EE da aso 53 Eegenen eegen deefe eege ees 53 5213 13 USB Op csi apt lila 53 5213 EA EE 53 Be A VOSS WOR EE 54 5 2 13 16 Disc CO 55 52 13 17 Auto Save Image EE 56 5 21316 Update Drive F W EE 56 Chapter 6 Trouble shooting 57 Ge PD OUT E E GE 57 6 2 About Error Messages oooomomccccccccocooononnncenonnnnonnnnnnnrnnnnnnnnnnnnnrrrnnnnnnnnnnnnrrnnrnnnnn 57 6 3
25. Image Press ENT to enter the next figure The default is Off Press W to select On Auto Save Image Off 5 2 13 18 Update Drive F W Now press ESC and Y to enter the following figure Only when you have installed some types of CDIDVD drives produced by ASUS or Plextor can this figure appear This function lets you udpate the firmware of some ASUS or Plextor CD DVD drives For the detailed types visit the Web site www acard com 13 18 Adv Setup Update Drive F W Press ENT to enter the next figure No F W File means that there is no file of firmware on the source reader So in the beginning you have to download the firmware of a certain type of CD DVD drive from the Web site of ASUS or Plextor Then record the firmware into a CD RW No F W File 56 ARS 2030PC Manual Chapter 6 Trouble shooting 6 1 About LCD After you power up if there is no display on the LCD check if the connection of power cord is firm and the environment of power outlet is normal 6 2 About Error Messages During Copy Test Compare and Verify etc if you press ESC to abort an error message will appear on LCD Abortion may cause the copy controller to hang up therefore you have to power on again If reading fails an error message will appear on LCD Get a new source DVD to try again If the copy controller hasn t detected any device after powering on an error message will appear on LCD 6 3 Compatib
26. NT LCD will show the message as follows Erasing disc 00 25 Quick When erasing finishes LCD will show the results as follows Quick Erase OK 03 5 2 11 18 Full Erase Now press ESC and Y to enter the following figure Full Erase is to erase the data on the DVD rewriteable discs completely Compared with Quick Erase Full Erase takes longer time to do the job 11 18 Setup Full Erase 46 ARS 2030PC Manual Press ENT to enter the next figure Use A W to confirm Yes or No All data will be lost erase Yes After confirming Yes and pressing ENT LCD will show the message as follows Erasing disc 45 00 Full When erasing finishes LCD will show the results as follows Full Erase OK 03 5 2 11 19 Auto Close Tray Now press ESC and Y to enter the following figure Auto Close Tray is to close the writer s tray automatically It is related to function 11 5 Auto Start Drive If you haven t set any writer to copy in function 11 5 this function will be invalid 11 19 Setup Auto Close Tray Press ENT to see the following figure Auto Close Tray 5 Here 5 means that it takes 5 seconds to close the writer s tray automatically after copying finishes and the tray is ejected Besides 5 seconds there are 10 15 20 25 30 35 40 45 and 50 seconds for choice If you have set one or all seven writers in function 11 5
27. T JC in the following figure means Job Counter that is every copying task It records the number of discs you have copied and can be deleted JC OK 000000001 Fail 000000000 Attention There is another record of LC Life Counter It also records the number of discs you have copied so far but can not be deleted You can veiw the record of LC by holding down ESC when LCD shows the finding of writers Press A to leave Press W The following figure shows the record in DVD writer 2 You can press W to see the records in other writers This kind of record can be deleted too 02 OK 000000001 Fail 000000000 Press A to return to the record of job Then press ENT to return to the next figure Disc Counter View 55 ARS 2030PC Manual Press to see the following figure It is to delete the record in job Use A W to confirm Yes or No Disc Counter Del Job Counter Press W again to enter the following figure Dev means the device of DVD writer Disc Counter Del Dev Counter Press ENT to see the following figure If you want to delete the record in DVD writer 2 you can press ENT otherwise press ESC to exit Del 02 Counter Ent Del Esc Exit 5 2 13 17 Auto Save Image Now press ESC and Y to enter the following figure Auto Save Image can save an image file automatically into your designated partition of HDD 13 17 Adv Setup Auto Save
28. all NpoAYKT ACARD KoTOpbIN HyxgaeTCA B peynpkynaynn MecTHOMy COopLuuky WEEE Statement Afin de g rer la quantit croissante de d chets lectriques et lectroniques de r duire l utilisation des d charges et des incin rateurs et d viter que des d chets nocifs ne polluent l environnement Union Europ enne a publi la directive WEEE sur les d chets lectriques et lectroniques Celle ci sp cifie que les fabricants doivent collecter recycler et traiter quipement lectronique et lectrique usag Depuis le 13 ao t 2005 les pays membres ont mis en place un syst me de recyclage gratuit selon le WEEE De ce fait Acard est responsable du recyclage de tous les produits export s vers Allemagne Vous pouvez mettre au rebut votre quipement ACARD usag dans votre centre local de recyclage Pour plus d informations sur les lieux de mise au rebut des quipements usag s destin s au recyclage veuillez contacter votre mairie votre service de traitement des d chets m nagers ou le magasin ou vous avez achet le produit RAEE Con la finalidad de reducir el incremento de residuos el ctricos y de material electr nico reduciendo el uso de los vertederos e incineradoras y prevenir el preocupante aumento del contacto de estos residuos con el medio ambiente Por este motivo la Uni n Europea ha fijado la Directiva de Residuos de Aparatos El ctricos y Electr nicos RAEE solicitando a los fabricantes la recolecci n recicla
29. ault is On Press W to select Off Display Time On 44 ARS 2030PC Manual 5 2 11 14 Button Sound Now press ESC and Y to enter the following figure Button Sound lets you control the sound of a button when you press it 11 14 Setup Button Sound Press ENT to enter the next figure The default is On Press W to select Off Button Sound On 5 2 11 15 Device Info Now press ESC and Y to enter the following figure Device Info shows the information of the DVD ROM and any of the DVD writers you have installed 11 15 Setup Device Info Press ENT to enter the next figure 00 CHO1 S MULTI PIONEER Press ENT to enter the next figure DVD RW DVR 112 1 22 5 2 11 16 System Info Now press ESC and Y to enter the following figure System Info shows the information of the system 11 16 Setup System Info Press ENT to enter the next figure DVD Flash Copier 2030PC ver 1 04U 45 ARS 2030PC Manual Press ENT to enter the next figure Fujitsu 29LV160B 2007 12 28 ACARD 5 2 11 17 Quick Erase Now press ESC and Y to enter the following figure Quick Erase is to erase the data on the DVD rewriteable discs quickly 11 17 Setup Quick Erase Press ENT to enter the next figure Use A W to confirm Yes or No All data will be lost erase Yes After confirming Yes and pressing E
30. be displayed on the LCD Copying 28 62 00MB 00 45 If the target disc has a smaller capacity than the source you will be prompted when the above copying process is completed to insert a new blank target disc to continue the copying process until the source is fully duplicated The following message will be displayed on the LCD Change next disk and press ENTER Insert a blank CD DVD and press ENT when you see the above message on the LCD Then the following message will be displayed on the LCD Copy next disk Please wait After the source is fully duplicated the following message will be displayed on the LCD The data volume and the copy time in the figure decrease while the completed percentage increases Upon completion of data copying the following message will be displayed on the LCD The successfully duplicated DVD will be ejected automatically Copy to DVD OK 03 SKIP 0 14 ARS 2030PC Manual 5 1 2 Verify The Verify function verifies the duplicated DVD Choose the second function Verify 2 Verify Press ENT to start data verification The following verification information will be displayed on the LCD Verifying 28 62 00MB 00 10 Upon completion of data verification the following message will be displayed on the LCD Verify DVD OK 5 1 3 Compare The Compare function compares the data in the sour
31. be used at a time Flash Card Box ENIS SATA HDD N27 LCD ARS 2030PC DVD Write CN DVD Write NI DVD Write ON ie Mind the notch position To connect the target DVD burners for Flash Copier Mode and DVD Copier Mode To connect the source SATA hard drive for DVD Large 4 pin Power 9 ARS 2030PC Manual Chapter 3 Basic Operations 3 1 The Keypad and LCD There are 4 keys and one LCD on the panel of the ARS 2030PC copy controller 1 Display all functions and messages 2 Scroll up the function list or the menu 3 Scroll down the function list or the menu 4 Execute the selected function 5 Abort the selected function SM Card Port Flash Drive Port CF MD Card Port Left Flash Card Status MS Card Port LED SD MMC Port Right ARS 2030PC System Status LED 3 2 Installing the All in One Card Reader for Flash Copier Mode If you want to duplicate flash cards an all in one card reader has to be correctly connected to the CNS port on the copy controller The system has to be set as Flash Copier Mode which is the default setting The default mode after each startup 3 3 Installing the hard drive for DVD Copier Mode An internal hard drive is not required for all system operations However the Image function is available only when a hard drive is attached With the Image function additional sources the image files in the hard drive can be used for DVD CD copying The following two sections are
32. ce flash media with that in the target DVD after the copying operation Choose the third function Compare Insert the source flash media into the proper slot on the card reader and the target DVD into the DVD burner 3 Compare Press ENT to start comparing data The following message of data comparing will be shown on the LCD Compare 5 80 0MB 02 50 Upon completion of comparing data the following message will be displayed on the LCD Compare 100 OK 3 15 ARS 2030PC Manual 5 1 4 Mem Card Info The Mem Card Info shows the basic information of the source flash media Choose the fourth function Mem Card Info Insert the source flash media into the proper slot on the card reader 4 Mem Card Info Press ENT and the following menu will be shown on the LCD File 133 Dir 6 85 9MB 5 1 5 Disc Info The Disc Info shows the basic information of the target DVD Choose the fifth function Disc Info Insert the target DVD into the DVD burner 5 Disc Info Press ENT and the following disc information will be shown on the LCD CH01 533 9MB File 4 You can browse the disc information of the different target discs with the buttons A and Y CH 01 File 1 Dir 0 4 4MB When the system is displayed the disc information of a certain target disc that DVD drive will be locked On the LCD CH is for the c
33. d disk First select the function by pressing W 9 05 Image PA Select Image After installing a hard disk your copy controller will format it automatically Each partition occupies 5GB The number of partitions is dependent on the hard disk s capacity The partitions are alphabetically arranged Select a partition by pressing A Y and LCD will show the message as follows Select Partition A DVD 4213 4MB After the partition is selected LCD will show the results as follows Set Partition to A 5 2 9 6 Image Src Drive This function is to select DVD ROM or any of the DVD writers as the source from which you can load data into a particular partition as an image file First select the function by pressing W 9 06 Image PA Image Src Drive Then use A Y to select DVD ROM or any of the DVD writers as the source Select Img Src 01 CHO1 S MUTLI 32 ARS 2030PC Manual After selecting the source such as DVD ROM you can press ENT and LCD will show the message as follows Load image from Drive 1D 01 5 2 9 7 Image Format Info This function is to see how you have formatted your hard disk It is related to function 12 4 Format HDD There are 3 formats for choice CD DVD and DL Double Layer Now press ESC and Y to enter the following figure 9 07 Image PA Image Format Info Press ENT to see the following figure This figure sho
34. ern reer ereen Confirm the closing of disc sessions Continue edit next Disc Ask if you want to continue the music disc editing End edit disc and bum Finish the music disc editing and start to copy Erase selected Tracks Abort the selected tracks and delete them Ins empty disc Continue Do you want to insert a blank disc and continue copying Insert Det de coi Insert the next audio disc NO AUDIO track in this disc The source disc has no audio track Sessions were closed already The disc sessions have already been closed Target Overflow He SGelect AAA SES The disc capacity is not enough to store the selected tracks Please select again Togt overflow del laSPUK Tira tie The disc capacity is not enough to store the selected tracks So do you want to delete the last track 4 Firmware Update Check Sum Error cocos The udpated firmware has errors Flash ROM Tall oi iaa Data cannot be written into Flash ROM Invalid firmware oooooocccconccocococononcccnoncconannnnnacccnnnnnnnannns The disc doesn t contain a valid firmware Last update F W Fal renren r resserrer The firmware is not updated successfully Last update F W ORT The firmware is updated successfully Searching FW ooooooccoooonocccononcnnaracinoncnonnororanancancness The system is searching for a valid firmware Source can t be Hard Disk During comparison the source cannot be hard disk
35. es 9 01 Setup Language Press ENT to enter the following menu The default setting is English You can change the display language to Spanish Japanese Traditional Chinese and Simplified Chinese Language English 5 1 9 2 DVD Burn Speed Now press ESC and Y to enter the following menu This function controls the burning speed of the DVD burner 9 02 Setup DVD Burn Speed Press ENT to enter the following menu The default value is Maximum You can change the burning speed to 20X 18X 16X 12X 8X 6X 4X 2 4X 2X and 1X depending on your need DVD Burn Speed Maximum 19 ARS 2030PC Manual 5 1 9 3 Eject Disc Now press ESC and Y to enter the following menu This function has 3 options Eject Good Only Eject All Disc and Do Not Eject When the Eject Good Only option is selected the system automatically ejects only those successfully duplicated discs When the Eject All Disc option is selected the system ejects all discs be it successful or failed When the Eject Good Only option is selected the finished disc has to be ejected manually 9 03 Setup Eject Disc Press ENT to enter the following menu The default setting is Eject Good Only Choose Eject All Disc or Do Not Eject with the Y button Eject Disc Eject Good Only 5 1 9 4 Button Sound Now press ESC and Y to enter the following menu This function co
36. g Under the circumstances return the control board to distributor for repair 6 9 About Function 13 and Cancellation If you want to execute function 13 Advanced Setup under DVD Copier Mode you can press ESC for 2 seconds And during operation if you want to cancel a function like Copy Test Verify and so on you can press ESC for 2 seconds too 58 ARS 2030PC Manual Appendix A LCD Messages 1 Normal Conditions All data will be lost erase All data on the disc will be lost Confirm the erasing of data PATA ZU EE Analyze the source disc Audio Disc Cantcomparel eee The system cannot compare the audio discs Cannot read TOC cues lada The system cannot read the contents of disc Check Target Please Wait ooooooooccconocccccccccccccccccccos The system is checking the target device Detect Deg orita e Detect what drives are connected with the system DVD RW does not Support the Func DVD RW doesn t support this function Erase Fntsbed AAA The erasing of data comes to an end EASING BE The system is erasing the data on the disc Fail to get Drive Intol neresen The drive information cannot be obtained Fail to get Src Disc into The information of source disc cannot be obtained Hold ESC 0 Ox iho eet e Press ESC for a second to terminate the test identical Baan ee ee eee eee eee The comparison results are the same Initialize SDRAM ooo denied eet ee tse eee In
37. hannel ID File for the file numbers and Dir for the directory numbers The total data size of the disc is displayed in the bottom of the message 16 ARS 2030PC Manual 5 1 6 Restore Card The Restore Card function restored the data on the target disc to the flash media Those restored data will be appended to the flash media as long as it has free space Choose the sixth function Restore Card Insert a flash media with enough free space into the card reader and the target disc with restoring data into the DVD burner 6 Restore Card Press ENT to start restoring data The following disc information will be displayed on the LCD Restore 0 4489 1MB 43 07 The completed percentage increases while the data volume and the copy time decrease Upon completion of data restoring the following message will be displayed on the LCD Restore to flash OK 5 1 7 Erase Disc The Erase Disc function erases data on the rewritable disc in the target burner Choose the seventh function Erase Disc Insert the target rewritable disc in the DVD burner 7 Erase Disc Press ENT to enter the following menu Select Quick Erase or Full Erase with the buttons A and Y This function clears the data on the rewritable DVD Full Erase takes longer than Quick Erase 7 01 Setup Quick Erase 17 ARS 2030PC Manual Press ENT to enter the following
38. in the burner and it can be changed To eject the failed DVD CD you have to press the eject key on the DVD burner Do not press any key during the copying process Abrupt interruption may damage the system and the DVD CD 3 3 2 Without an Internal Hard Drive When a 3 5 inch SATA hard drive is not connected to the ARS 2030PC please follow the operational procedures below Insert a source DVD CD into the DVD burner m Switch the first function Copy by pressing A or Y Insert a blank DVD CD into the DVD burner and press ENT to start copying m Upon completion of data copying the successfully duplicated DVD CD will be ejected automatically The default setting is automatic ejection and it can be changed The failed DVD CD will be held in the DVD burner The default setting keeps the failed DVD CD in the burner and it can be changed To eject the failed DVD CD you have to press the eject key on the DVD burner Before installing any hardware please check the SATA cable first An SATA hard drive is directly connected to the SATA port on the ARS 2030PC with an SATA cable Connecting to the SATA port Connecting to the SATA port on the ARS 2030PC on the SATA hard drive burner 11 ARS 2030PC Manual An IDE burner is directly connected to the IDE port on the ARS 2030PC with an IDE cable Connecting to the IDE port on the ARS 2030PC Connecting to the IDE port on the IDE burner Note When the SATA connector
39. ing figure CD G is a kind of special copying format This function supports this special format 13 11 Adv Setup CD G Press ENT to enter the next figure The default is Off Press W to select On CD G Off 5 2 13 12 ISRC amp MCN Now press ESC and Y to enter the following figure ISRC and MCN are special copying formats This function supports them 13 12 Adv Setup ISRC amp MCN Press ENT to enter the next figure The default is Off Press W to select On ISRC 8 MCN Off 5 2 13 13 USB Option Now press ESC and Y to enter the following figure USB Option lets you switch to the USB mode if your copy controller has connected with a PC 13 13 Adv Setup USB Option Press ENT to enter the next figure The default is Off Press W to select On USB Option Off When USB option is On the original 13 Adv Setup will change to 14 Adv Setup and the hidden 12 USB Mode will appear in the first layer of function menu 5 2 13 14 CD TEXT Now press ESC and Y to enter the following figure CD TEXT is a kind of special copying format This function supports this special format 13 14 Adv Setup CD TEXT 53 ARS 2030PC Manual Press ENT to enter the next figure The default is Off Press W to select On CD TEXT Off 5 2 13 15 Password Now press ESC and Y to enter the following figure Password is set
40. itialize the memory of the system Load Default Confg Do you want to load the default settings No Erasable DiscmDNVD PWI The disc on the DVD RW device is not rewritable d LEE The system is preparing to record Press a Key to Eject Fail Disc Press any key to eject the failed disc after copying Press a Key to Eject Good Disc Press any ket to eject the good disc after copying Read disc error cc caca aere During comparison the disc cannot be read Save new config Fall ccoo The new setting of configuration cannot be saved Source Disc Emptvil t nano The source disc doesn t contain any data Source Disc Not Read Source disc is not ready to be read Source Drive Not Read Source drive is not ready to read Src amp Tgt can t in the same channel E Ge During comparison the source and target discs cannot be in the same channel Target Disc Not Empty ovocitos le EeN The target disc still has data Target Disc Not Read Target disc is not ready to be written into Target Drive Not Read Target drive is not ready to write Target overflow The target disc hasn t enough capacity to store new data TOC not match The comparison results are not the same en d EE Cancel the job during operation 2 Connecting with a HDD All data will e Eu E GEES Ee All data on the hard disk will be lost Confirm the formatting of hard disk Delete Image in Partition xx Confirm the deleting of data image in partiti
41. je y tratamiento de ests residuos correctamente Los paises miembros ya han establecido su sistema de reciclaje gratuito de RAEE antes del 13 de Agosto del 2005 Por este motivo ACARD es el responsable del reciclaje de todos los productos exportados a Alemania Usted puede devolver su producto Acard a un punto de recogida local cuando desee reciclarlo Dichiarazione WEEE Per far fronte all aumento dei residui delle apparecchiature elettriche ed elettroniche ridurre l uso di materiale di riporto e degli inceneritori ed impedire che il materiale nocivo delle apparecchiature residue entri a contatto con l ambiente l Unione Europea UE ha stabilito le Direttive sui Residui delle apparecchiature Elettriche ed Elettroniche WEEE chiedendo ai fornitori di raccogliere correttamente riciclare e trattare le apparecchiature elettriche ed elettroniche residue Le nazioni facenti parte dell Unione Europea hanno gia stabilito il loro sistema gratuito di riciclaggio di questo materiale WEEE prima del 13 agosto 2005 Di conseguenza ACARD responsabile del riciclaggio di tutti i prodotti esportati in Germania Potete restituire il vostro prodotto acquistato da ACARD che deve essere riciclato da un azienda specifica locale ARS 2030PC Manual Chapter 1 Introduction 1 1 Overview ARS 2030PC Card Reader to DVD Duplicator is a standalone copy controller with USB Card Reader supporting high speed DVD burning It does not need connecting to a compute
42. lar n n cevreye yay lmas n onlemek icin Avrupa Birligi AB ureticilerden elektrik ve elektronik madde at klar n gerektigi gibi toplamalar n geri donusturmelerini ve kimyasal isleme tabi tutmalar n talep etmek icin Elektrik ve Elektronik Madde At klar uzerine bir direktif haz rlad Topluluk uyeleri 13 Agustos 2005 ten once elektrik ve elektronik madde at klar n n ucretsiz geri donusum sistemlerini coktan olusturmuslard Bundan dolay ACARD Almanya ya ihrac ettigi butun urunlerin geri donusumunden sorumludur ACARD urunleri geri donusum gerektirirse yerel toplayicilara geri verebilirsiniz WEEE GtoneTeHb UTO6bl cl IpaBuTbCA C YBenvUY4UNBAwLUINMCA HOHYKHbIM INEKTPUYECKUM N INEKTPOHHbIM o6opyA0BaHuem yMeHbLUIMTe UCNONb3OBAHNE 3akKanbIBAHUA Mycopa H UCNONb3OBAHAA YCTAHOBKU Ana CKnraHna OTXOAOB MpenaTcTByUTe BpeaHomy BbIOPOCaM 3arpa3HaTb OKpykaHOoBKu CDe EBpone cku coro3 EC ycraHoBun AnpekTuBy no HeHykHoMy OnekTpuyeckomy n OnekTpOHHOMy O6bopyaoBaHuto WEEE ana Toro uTOBb usroToBuTenen coOpann nepepabaTbiBanu n BOOOLIe MPOABUNM BHNMAHNE K HEHYKHOMY INEKTPUHECKOMY N 3NEKTPOHHOMY o6opyAoBaHut AOJMKHbIM OOpaz3om neut Halu ycraHoBunim GecnnatHylo CUCTEMyY n 3NeKTPOHHOMy O ODVDOBSHMIO AOJDKHBIM OOpa3om UneHbl Hann ycTaHoBunu SecnnatHyto cuctemy nepepabotku WEEE po 13 aBrycta 2005 CooreBercreeHHo ACARD o6a3aH ObITb OTBETCTBEHHbIM 3a TO YTO NepepaboTan BCe NpOAYKTbI aKcnopTupyemble B TepmaHuto Bol MOXETe BO3BPaTHTb B
43. le Flash Media The following flash media have been tested and they function normally with the ARS 2030PC Memory Card Support CF slot CF MD up to 16 GB SD solt SD SDHC up to 32GB MS solt MS MS pro MS duo MS pro duo SM slot XD XD M XD H SM 6 4 About DVD ROM DVD Writers lf a DVD ROM or a DVD writer cannot read confirm the format of the source DVD and check if it is damaged Use another DVD writer to read the source DVD If it works the DVD ROM is probably defective or not compatible with the source DVD 6 5 About Buttons If you press any one of the four buttons on the panel but there is no response it is perhaps that the button cannot function well Inspect the jumper setting 6 6 About DVD Writer Not Readable After copying if the DVD writer is not readable use Compare to examine or get another DVD ROM to test 57 ARS 2030PC Manual 6 7 About High Failure Rate If the failure rate of copying is high do the following things to improve e Lower the speed of DVD writer e Inspect if the blank disc s quality is good e Update the firmware e Inspect the DVD writer s maximum writing speed If the speed is over 8X copy the data to a hard disk first and then transmit to DVD 6 8 About Firmware Update If you cannot update the firmware please inspect the firmware Perhaps you have downloaded a wrong file Failure in firmware update may cause the copy controller to fail in bootin
44. lows Src 02 DVD RW TOC not match 5 2 6 Prescan Function 6 Prescan is to scan if the source DVD can be read correctly and by the way to test the reading speed 28 ARS 2030PC Manual Select function 6 Put the source DVD into DVD ROM 6 Prescan Press ENT to prescan LCD will show the scanning information as follows Scaning DVD 0 4213 4MB 7 30 When scanning finishes and the source DVD can be read correctly LCD will show the results as follows PreScan OK 5 2 7 Disc Info Function 7 Disc Info is to generate a simple report of the source Select function 7 Put the source DVD into DVD ROM 7 Disc Info Press ENT and LCD will show the DVD information as follows Disc Type DVD ROM 4213 4MB 7 30 5 2 8 Select Source Function 8 Select Source is to identify and assign source drives Select function 8 8 Select Source Press ENT and then press A Y to select the source as shown below Src DVD ROM 01 IDE1 Master After selecting the source such as DVD ROM you can press ENT and LCD will show the message as follows DVD ROM selected 29 ARS 2030PC Manual Suppose you select HDD as the source and try to copy from one of its partitions but the partition contains no data an error message will appear on LCD At this moment you can switch to another partition that contains data or
45. ng to P A 0 When moving finishes LCD will show the results as follows Moving to P A OK If the chosen partition has contained image data the system will ask to overwrite or keep the data Press A to overwrite Image Exists Overwrite Yes After pressing A LCD will show the moving information as follows Moving to P A 0 When moving finishes LCD will show the results as follows Moving to P A OK 5 2 10 3 Play Audio Track This function is to make the copy controller act as a music player You can connect a headphone to the headphone jack on the source and enjoy the music 39 ARS 2030PC Manual Now press ESC and Y to select the function 10 03 Edit Track Play Audio Track Use A Y to select the track you want to play Select Track 110 03 25 After selecting and pressing ENT LCD will show the playing information below Playing Track 1 00 00 03 25 5 2 10 4 Close Session This function is to close CDs and let no data written into After closing you can put the CDs on any normal player and listen Now press ESC and Y to select the function 10 04 Edit Track Close Session After pressing ENT the system will ask if you are sure to close Close all disc s session Yes After pressing ENT LCD will show the message as follows Closing Session Please wait
46. nische Altgerate umweltgerecht einzusammeln zu recyceln und zu entsorgen Die Mitgliedsstaaten der EU haben bereits ihre kostenfreien Recyclesysteme konform der WEEE vor dem 13 August 2005 eingerichtet Entsprechend der Richtlinie ist ACARD verantwortlich fur die umweltgerechte Entsorgung aller nach Deutschland exportierten ACARD Produkte Sie k nnen Ihr zu entsorgendes ACARD Produkt zu Ihrer rtlichen Sammelstelle bringen AEEA verklaring Met het doel de stijgende hoeveelheid afgedankte elektrische en elektronische apparatuur te beheersen zonder hiervoor onnodig stortplaatsen en verbrandingsovens te belasten en om de vervuiling van het milieu door vrijkomende stoffen uit de afgedankte apparatuur te voorkomen heeft de Europese Unie EU de richtlijn betreffende afgedankte elektrische en elektronische apparatuur besloten Deze richtlijn verplicht fabrikanten afgedankte elektrische en elektronische apparatuur in te zamelen te recyclen en te verwijderen De lidstaten van de EU hebben reeds de kosteloze recyclesystemen volgens de AEEA voor de 13 augustus 2005 ingericht Conform de richtlijn is ACARD verantwoordelijk voor de verwijdering van alle naar Nederland ge xporteerde ACARD producten U kunt uw afgedankt ACARD product naar uw locale inzamelplaats brengen Elektrik ve Elektronik Madde At klar Demeci Elektrik ve electronik madde atiklarinin yukselmesiyle basedebilmek arazi doldurma ve cop yakma firini kullan m n azaltmak atik madde zarar
47. nter the following figure The function DVD Burn Speed lets you control the burning speed of DVD writers 11 03 Setup DVD Burn Speed Press ENT to enter the following figure The default is maximum DVD Burn Speed Maximum 41 ARS 2030PC Manual 5 2 11 4 Read Speed Now press ESC and Y to enter the following figure The function Read Speed lets you control the reading speed of target CDs 11 04 Setup Read Speed Press ENT to enter the following figure The default is maximum but there are still other choices 32X 16X and 8X Read Speed Maximum 5 2 11 5 Auto Start Drive Now press ESC and Y to enter the following figure Auto Start Drive is to copy or test automatically once you put blank DVDs into the writers 11 05 Setup Auto Start Drive Press ENT to enter the following figure The default is Off Press t to select 1 one blank DVD Auto Start Drive Off 5 2 11 6 Startup Menu Now press ESC and Y to enter the following figure Startup Menu lets you select any one of the functions except Adv Setup as the first item appearing on the menu whenever you turn on the copy controller 11 06 Setup Startup Menu Press ENT to enter the following figure The default is Copy You can certainly select any other function as the first item but remember to press ENT to confirm Startup Menu 1 Copy 5 2 11 7 Auto Verify
48. ntrols the sound of the button when it is pressed 9 04 Setup Button Sound Press ENT to enter the following menu The default setting is On You can change it to Off by pressing V Button Sound On 5 1 9 5 Device Info Now press ESC and Y to enter the following menu This function shows the information of the DVD ROM and all the DVD burners connected to the controller 9 05 Setup Device Info Press ENT to enter the following menu 00 IDEO Slave S MULTI PIONEER Press ENT to enter the following menu DVD RW DVR 112 1 24 20 ARS 2030PC Manual 5 1 9 6 System Info Now press ESC and Y to enter the following menu This function shows the system information 9 06 Setup System Info Press ENT to enter the following menu DVD Flash Copier 2030PC ver 1 04U Press ENT to enter the following menu Fujitsu 29LV160B 2007 12 28 ACARD Press ESC to exit the menu when you finish 5 1 9 7 Update Firmware Now press ESC and Y to enter the following menu Burn the firmware onto the disc insert the disc into the burner and close the disc tray You can download the firmware at www acard com 9 07 Setup Update firmware Press ENT and follow the prompts to update the firmware The No F W File message means that there is no valid firmware file on the source disc You have to download the proper fi
49. on xx FORMatADD eegene Ee Ask if you want to format the hard disk Format HDD ORT The Formatting of hard disk has been completed HDD not Formal c lt cocos ri tt ceusdeade The hard disk hasn t been formatted yet FDD t00 SMall ist A ee eee eee The capacity of hard disk is too small HDD too small to handle made E The hard disk hasn t enough capacity to store the data image at least 5Gbytes Image Exists Overwrite e a a E a pa ra EE E EEEE EE Oe e Aa Eiaa a a ta There is a data image in the current partition Confirm the overwriting of data Image load Fail The image isn t successfully loaded from DVD to the hard disk Image load OK cee The image is successfully loaded from DVD to the hard disk 59 ARS 2030PC Manual No Image in Partition xn There is no data image in partition xx No Valid HDDI lt tit The system cannot find a hard disk Partition Damage ii is ee eee The partition is damaged Select HD First ccc io Select a formatted hard disk at first Verify Disk or Partition Do you want to verify the hard disk or just a partition Verify Hard Disk Fall The hard disk is not verified successfully 3 Audio Editing Burn OF Move to DarttON corria ei dens toad bu gece EE Do you want to directly copy the data into disc or move them to the partition Can t edit HDD The hard disk cannot be edited as a source audio disc Close all dscesession ne
50. r or require much learning Simply through the LCD and the button on the panel you can make a DVD via USB Card Reader to burn direct to a DVD quickly It is designed for the user who is looking for a way of making instant backup memory card data more efficient and much simple solution such as personal SOHO and office users 1 2 Features Standalone USB to IDE DVD CD copy controller m Totally independent without installing hardware or software Supports a built in 3 5 SATA hard disk drive m Supports high speed DVD CD recording Backs up DVD CD in minutes m Has a user friendly interface and shows messages with LCD Provides optional functions to extend application Firmware update by DVD ROM 1 3 Specifications ACARD ATP865 IDE processor m ACARD ARC772 IDE SATA bridge m 32 bit RISC CPU 64MB DDR memory for data buffer m 3 independent IDE interface channel m 1 SATA interface channel m 2 USB interface channel for USB Card Reader m 2 x 16 LCD screen m A membrane 6 buttons operation panel m 512KB of flash memory for boot loader m 2MB of flash memory for copy code Dimension 150mm W x 42mm H x 215mm D m Power Source DC 5V 1 4 System Requirement m Upright external case 5 6 x 5 25 m A 300W power supply m ATA133 cable DVD writer x 3 a A hard drive optional A removable hard drive rack optional AEC 4420P optional for DVD Copier Mode only 7 ARS 2030PC Manual Chapter 2 Hardware
51. rburn 13 03 Read Error Skip 13 04 Rormat HDD 13 05 Verify HDD 13 06 Burn in 13 07 Update Firmware 13 08 Compare Firmware 13 Adv Setup 13 09 H W Diagnostic 13 10 Load Default 13 11 CD G 13 12 ISRC 8 MCN 13 13 USB Option 13 14 CD TEXT 13 15 Password 13 16 Disc Counter 13 17 Auto Save Image 13 18 Update Drive F W 25 ARS 2030PC Manual ARS 2030PC Manual Among the 11 functions Function 10 Edit Track is designed exclusively for editing a collection of favorite songs from CDs During operation if you don t understand an LCD message see AppendixA 5 2 1 Copy Function 1 Copy is copy functions allows instant copy of source original disc image to the target drives burners Before copying be sure that the source DVD is placed into DVD ROM or there are data in a certain HDD partition if you have installed a hard drive If you are not so sure of real copying use Function 2 Test to simulate first Select function 1 Put a source DVD into DVD ROM and blank DVDs into the DVD writers A rewriteable DVD containing old data is also usable but the old data will be automatically erased 1 Copy After the DVD ROM and DVD writers detect DVDs press ENT to start copying LCD will show the copying information as follows
52. rmware and burn it onto a disc to update the firmware Updating the firmware may damage your system Note Do not turn off the power during firmware updating Otherwise the system may be damaged 5 1 9 8 Compare Firmware Now press ESC and Y to enter the following menu This function compares the current version of firmware and the newly download firmware It verifies whether the download version is the latest 9 08 Setup Compare Firmware 21 ARS 2030PC Manual 5 2 DVD Copier Mode This mode uses the hard drive as the default source for data copying Here as an introductory example we use one of the burners as the copying source Note To use the hard drive as the source you have to load the data on the disc to some partition of the hard drive first Next you should carry out the HDD to DVD CD copying i e 1 to 3 If you use one of the burners as the copying source you should perform the 1 to 2 copying operation The copy controller has 13 functions in total 7 sub functions under the ninth function 4 sub functions under the tenth function 21 sub functions under the eleventh function and 18 sub functions under the twelfth function These functions are listed below 1 Copy 2 Test 3 Test 8 Copy 4 Verify 5 Compare 6 Prescan Copy Controller 7 Disc Info 8 Select Source 9 Image 10 Edit Track
53. ssage on LCD as follows after it finds the new firmware Then press ENT to update Searching F W XXX XXXX 51 ARS 2030PC Manual 5 2 13 8 Compare Firmware Now press ESC and Y to enter the following figure Compare Firmware is to compare the current firmware version and the newly downloaded version It can prove if the downloaded version is the newest one 13 08 Adv Setup Compare Firmware 5 2 13 9 H W Diagnostic Now press ESC and Y to enter the following figure H W Diagnostic is to test the system 13 09 Adv Setup H W Diagnostic Press ENT to enter the next figure and begin the LCD test After that the system will do the button test self test of SDRAM the hardware connection test and flash test All test results will be shown on LCD It is the easiest way to know if the system can work well LCD Test Start When all tests finishes LCD will show the message as follows Test finished 5 2 13 10 Load Default Now press ESC and Y to enter the following figure Load Default is to make all changed settings return to defaults 13 10 Adv Setup Load Default Press ENT to enter the next figure Use A W to confirm Yes or No Load Default Config Yes When default loading finishes LCD will show the results as follows Load Default OK 52 ARS 2030PC Manual 5 2 13 11 CD G Now press ESC and Y to enter the follow
54. to protect your copy controller 13 15 Adv Setup Password Press ENT to see the following figure The default is Off Password Off Press to see the following figure Change means to change a preset or an old password into a new one Password Change Press to see the following figure Old Password 2 Use A Y to key in the default 85122290 A password should be composed of 1 to 13 characters The character can be A B C etc or 1 2 3 etc or the combination of both After selecting a desired number or alphabet remember to press ENT Old Password 8 After keying in the old password remember to press ENT to confirm Then the following figure will appear New Password 9 Follow the rule mentioned above to key in a new password After keying in the system will ask you to enter the new password again Re Ent Password 2 54 ARS 2030PC Manual When it is correct you will see the following figure You have 3 chances to enter your password If you forget your password return the copy controller to ACARD for help Change OK 5 2 13 16 Disc Counter Now press ESC and Y to enter the following figure Disc Counter records how many discs you have copied 13 16 Adv Setup Disc Counter Press ENT to see the following figure View means to see the records Disc Counter View Press EN
55. track or more from CD ROM and then copy into blank CD R RWs 10 01 Edit Track CD to CD Edit Now press ENT and you will enter the following figure Here 1 10 means the number one of the 10 tracks and 03 25 means the length of track Select Track 1 10 03 25 You can press W to see the second track and so on Suppose we decide to select the first track then press ENT A will appear beside 1 10 as shown below But pressing ENT again may cancel the selection Select Track 1 10 03 25 After selecting please use A to move to the End menu as shown below Select Track End 1Trk03 25 34 ARS 2030PC Manual Press ENT to finish the CD editing and use A Y to confirm Yes or No End edit disc and burn Yes LCD will show the copying information as follows Copying 24X Edit 1110 gt 1 1 1 1 means the first track of all tracks we have selected and here we have just selected one track When copying comes to an end LCD will show the message as follows Burn Complete OK 03 The system will ask if you want to keep editing Please use A W to confirm Yes or No as shown below Continue edit next Disc Yes If you want to keep editing the current source CD will eject auctomatically and the system will ask you to insert another new CD as shown below Insert next disc After inserting the new
56. with a metal latch is inserted to the controller it will give a clear metal snapping sound indicating that the connector is firmly connected to the socket To remove the connector please press the metal latch first before pulling out the SATA cable Do not pull the cable out directly by force Chapter 4 The PCB Layouts The PCB layout of the ARS 2030PC is shown below O was _O N FHH 0 JM A SN d HH e CN11 ous E E peeeeecccen S3sssssses sssssesse houng peeeccccen ERRE eo pu m 1 CN1 the large 4 pin power port CN27 CN1 2 CN9 CN11 The target DVD CD burner connector Flash Copier Mode 3 CN13 The USB data cable connector 4 CN27 The source SATA hard drive connector DVD Copier Mode Note The CN13 connector has a missing ping alignment setup Please align the pins correctly before inserting the connector Do not insert the connector by force 12 ARS 2030PC Manual Chapter 5 Operational Functions The ARS 2030PC has two operational modes DVD Copier and Flash Copier The default setting is Flash Copier Mode Users can select the operational mode through the Model Select function 5 1 Flash Copier Mode The copy controller has 9 functions in total 8 sub functions under the ninth function These functions are listed in the following figure 1 Mem Card Copy 2 Verify 3 Compare 4 Mem Card Info Copy Controller
57. ws that the hard disk has been formatted as DVD Image Format Info Auto 5 2 9 8 Edit This function is to name a certain partition but only when the partition contains an image file can title editing be valid First select the function by pressing W First select the function by pressing W 9 08 Image PA Edit Press ENT A title should be composed of 1 to 13 characters The character can be A B C etc or 1 2 3 etc or the combination of both Use A W to select the number or alphabet After selecting a desired one press ENT Edit Title After keying in the title press ENT to see the following figure Edit Sub1 Title 33 ARS 2030PC Manual Sub1 Title lets you key in a subtitle 1 You can press ENT again to key in a subtitle 2 When title editing is completed you will see the next figure Edit Title OK 5 2 10 Edit Track for CD only Function 10 Edit Track is exclusively designed for editing a collection of favorite songs from CDs In other words it can collect different tracks songs on a number of CDs and merge them into a single CD This function includes 4 subfunctions CD to CD CD to HDD Play Audio Track and Close Session Refer to page 24 for the menu Select function 10 10 Edit Track 5 2 10 1 CD to CD Edit Now press ENT and you will enter the following figure Here the function CD to CD Edit lets you select a
Download Pdf Manuals
Related Search