Speed Dome Camera Controller Operation Manual
Contents
1. 1 For PELCO D and PELCO P Protocols the way of operation is as follows Set the Starting Scan Position Transfer the speed dome to the starting scan position operation AUTO ON Set the Ending Scan Position Transfer the speed dome to the ending scan position operation AUTO OFF Run Auto Pan AUTO ENTER 2 Auto Pan operation takes the following parameters You must set these parameters before using a Auto Pan command to begin the scan operation You can use the scan Stop command or PT scan stop command to stop the scan Setting scan condition Auto Pan Position First specify position second specify position Auto Pan Speed and Direction Stop Auto Pan AUTO OFF only for COP 2 protocol or push the joystick to stop scan 5 Control the Zoom of the Camera firstly press LENS CTRL SWITCH you can see Lens Zoom CTRL showed on the LCD secondly press ZOOM WIDE ZOOM TELE to execute the function Control the Focus of the Camera firstly press LENS CTRL SWITCH you can see Lens Focus CTRL showed on the LCD secondly press FOCUS FAR FOCUS NEAR to execute the function Control the Iris of the Camera firstly press LENS CTRL SWITCH you can see Lens Iris CTRL showed on the LCD secondly press IRIS OPEN IRIS CLOSE to execute the function Enter menu ON Back Light of Keyboard Screen CALL 5 ON CALL 5 OFF Version number display CALL 211 ENTER Use the Joy2. IRIS OPEN FOCUS NEAR ZOOM WIDE 2 IRIS CLOSE FOCUS FAR ZOOM TELE To execute the function which LENS CTRL SWITCH selected there is three function iris close focus far zoom tele ON MENU Switch on the setting of function OSD MENU OFF Switch off the setting of function SHOT To call cruising track CAMIID Select address of the intelligent Speed Dome CLEAR To clear inputted data 0 9 Number key Enter To confirm CALL To call the preset position PRESET To set the preset position JOYSTICK Control the upward downward leftward and rightward speed motion of the speed dome Power LED a Rear Panel Figure 2 RS 485 TA NC TB Figure 2 1 Power input connector input 12V DC power 2 Communication connector RS 485 i Select Protocol of the Keyboard 1 Protocol Setting press CALL 200 ON LCD will show Display Select Protocol and turn the joystick left or right to select the protocol you wanted press Enter to save the protocol 2 Protocol type PELCO D 2400bps PELCO D 4800bps PELCO D 9600bps PELCO P 4800bps PELCO P 9600bps COP 2 9600bps I Operation of the Keyboard 1 Select Address of the Speed Dome Camera CAM N Enter Display Current CamID 001 Description N No of camera from 0 to 255 Function Select the address of the camera to be controlled When the value N is in con
3. OKINAGs PTZ KB050X 3 AXIS PTZ KB050 2 AXIS Speed Dome PTZ Controller Operation Manual PTZ KB050X PTZ KB050 Please read this operation manual before using this device and use the device properly Also please keep this manual with care to ensure easy access at any time The Sketch of the Front Panel and Description of Buttons P Rear Panel i Select Protocol of the Keyboard I Operation of the Keyboard fj Installation and Connection Wl Technical Specifications Bf Points for Attention fj Package Contents i Summary The keyboard controller is used for terminal receivers such as the intelligent speed dome etc It is very easy for operating and setting the speed dome camera The controller is also to control the terminal receiver to achieve the function of controlling pan tilt lens and etc Taking the EIA RS 485 electrical interface between the keyboard and the receiver One keyboard can control as much as 128 speed dome The maximum communication distance between the keyboard and the receiver is up to 0 75 mi 1 2 km gt Introduction of the keyboard Panel The Sketch of the Front Panel and Description of Buttons Figure 1 Figure 1 1 LCD 2 AUTO To control auto horizontal rotation for Pan Tilt 3 LENS CTRL SWITCH To select the following function gt IRIS FOCUS ZOOM 4 IRIS OPEN FOCUS NEAR ZOOM WIDE To execute the function which LENS CTRL SWITCH selected there is three function
4. amera and Controller Port to multi port and half duplex function Communication connector RS 485 Baud Rate of Communication Four baud rates i e 2400bps 4800bps and 9600bps Distance of Communication 3900ft 1200m in maximum Power Supply 12V DC 1V 1A Size 5 12 L x 7 48 W x 2 52 H 130 L mm x 190 W mm x 64 H mm Weight 1 16lbs 525g Number of controlled speed dome camera up to 128 BM Points for Attention Please read the operation manual of the keyboard carefully before using it The keyboard takes 12V DC power supply Please confirm the voltage and polarity before the power supply is switched on Do not place the keyboard under the rain or on wet place so as to avoid short circuit or electrical shock As the keyboard is a sophisticated electronic device you should never open the case so as to avoid the occurrence of trouble The keyboard has integrated multiple protocols and you are pleased to select correct protocol and the baud rate When switching on power supply take care of the selected protocol and the baud rate on the first screen Bj Package Contents One 1 Controller Keyboard One 1 Power Supply One 1 Manual
5. formity with the address of the Speed Dome Camera it will be under control Set the Preset Position PRESET N Enter Display Preset No 001 Description N No of preset position from 1 to 255 Function Store current position and refer it as No N position Call the Preset Position CALL N Enter Display Call Number 001 Description N No of preset position from 1 to 255 Function Transfer the camera to the position of No N preset position Cancel the Preset Position PRESET N OFF Display PresetNo 001 Description N No of preset position from 1 to 255 Function Delete the No N preset position stored Set the Cruise Track COP 2 PELCO D PELCO P Available Enter the Status of Track Setting SHOT N ON N No of track from 1 to 6 Display Track 01 Sum 06 Description Track No 1 is currently setting in which there are 6 preset points Edit Track Press TELE to edit down page and press WIDE to edit up page Each track involves 16 preset points and the running speed and the dwelling time of each preset position Display No 01 Point 001 Description The 1st preset position in the track is 001 Display No 01 Speed 001 Description The speed of the 1st preset point in the track is the 1st class Display No 01 Time 004 Description The dwelling time of the 1st preset point in the track is 4 Seconds Speed Range 1 to 8 from the fastest to the lowest A
6. ny speed outside the range will be referred as the 1st class the range of the dwelling time is 1 to 255 When the No N preset point is set as No 0 then all preset points before the No N preset point in the track will be valid however all numbers of preset points afterward and their speed and dwelling time shall be set as 0 automatically After tracks are edited press OFF to store and exit while push the joystick to exit without storage Run Cruise Track SHOT N Enter Display Input TourNo 01 Description N No of the track from 1 to 6 Function Tour the No N track and stop tour by pushing the joystick Stop Cruise Track SHOT N OFF Display Input TourNo 01 Description N No of the track from 1 to 6 Function Stop the No N track or stop tour by pushing the joystick Cancel Cruise Track SHOT N OFF Pressing OFF down until Clear Tour OK appears Display Input TourNo 01 Description N No of the track from 1 to 6 Function Delete the No N track Auto Pan ON Operation of COP 2 Protocol AUTO P1 ON P2 OFF Display Input 1stNo 001 Description P1 the starting scan No of preset point from 1 to 255 which should be set already Display Input 2nd No 002 Description P2 the ending scan No of preset point from 1 to 255 which should be set already If P1 P2 or P1 and P2 are coincided the speed dome will make scan in range of 360 Note
7. stick to control the speed dome camera You can use the speed joystick to control the Pan Tilt direction and speed of the speed dome randomly The speed of pan tilt is decided by the angle of the joystick you operated Figure 3 Change the tilting angle of the joystick you can adjust the speed evenly and the camera can be focused automatically in the course of scan to keep images being distinct Aa LEFT lt gt RIGHT JOYSTICK Figure 3 18 In case error operation occurs normal display will be recovered after Error Operation appears for 1 second Installation and Connection Attention Please read the operation manual of the keyboard and the speed dome carefully before connecting wires Any incorrect connections can cause permanent damage of the device When connecting wires first switch off the power supply of all devices The communication wires between devices should be shielded twisted cable When installing cables they should be far away from high voltage lines or other possible interference circuits as can as possible 1 The marking of wires of the transfer box Figure 4 Figure 4 Connections of the keyboard controller controlling multiple speed dome cameras Figure 5 Connections between the keyboard and the speed dome camera Figure 6 Speed dome Speed dome Speed dome Speed dome N Speed dome RS485 OUT Figure 6 Figure 5 BW Technical Specifications Communication between Speed Dome C
Download Pdf Manuals
Related Search