FA260RF INSTALLATION INSTRUCTIONS UL
Contents
1. Local to use the House ID programmed into the FA260RF Program Address 3 Note f the House ID Sourceis e System 1 RF keypad and bi directional units MUST match the House D programmed into the control pand e Local 0 RF keypad and bi directional units MUST match the House D programmed into the FA260RF Press the key to continue Alternately flashes hl and either 1 or 0 Step Action Display 5 Enter 6 Receiver Enable Enter 1 to enable or 0 to disable Alternately flashes r and Enable the receiver if RF transmitters or wireless keypads are either 1 or 0 programmed into the control Note M ake sure the number of recdvers set for Enable 1 does not excead the capacity of the control pand Press the key to continue Enter 7 Transmitter Module Enable Enter 1 to enable or 0 to disable Enter 1 if bi directional devices are being used Note If the House D Sourceis System and more than one FA260RF is used make sure only one has the Transmitter Module enabled See Note unde House ID Source step 4 Press the key Alternately flashes tE and either 1 or 0 7 Enter 0 High Security Mode To put the system into High Security mode enter 1 Enter 0 to disable En 8 Press the key to exit the FA260RF Program mode READY or NOT READY Note This is all the FA260RF programming neces2. robbery fire or otherwise or that the products will in all cases provide adequate warning or protection Customer understands that a properly installed and maintained alarm may only reduce the risk of a burglary robbery fire or other events occurring without providing an alarm but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result CONSEQUENTLY SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJ URY PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING HOWEVER IF SELLER IS HELD LIABLE WHETHER DIRECTLY OR INDIRECTLY FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE REGARDLESS OF CAUSE OR ORIGIN SELLER S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER This warranty replaces any previous warranties and is the only warranty made by Seller on this product No increase or alteration written or verbal of the obligations of this Limited Warranty is authorized alas 175 Eileen Way Syosset NY 11791 f Alert Copyright 2000 PITTWAY CORPORATION WWEPROFESSIONAL SAS Fe SYSTEMS K4456V1 8 00
3. s If using an RF keypad on only one partition the FA260RF s partition assignment must match the partition set in field 1 48 f set for Local on a partition control the FA260RF s partition assignment must match the partition programmed in the BD device Installing the FA260RF Locate the FA260RF in an area and at a height where it is convenient for users to operate the system The FA260RF must be at least 10 from the control panel to ensure proper operation of the RF receiver Toinstall the FA260RF refer to Figure 1 for wiring connections and perform the following steps Step Action 1 Remove the case back by pushing down the two snaps along the FA260RF s bottom edge and pulling the case apart 2 Route the wiring from the control panel through the opening in the case back See the control panel s instructions for proper wire run lengths oo a OL 0 EO 3 Mount the case back directly to a wall or electrical gang box O 4 Connect the power and data wires from the control panel to the terminals on the 0 o FA260RF TAMPER 5 Connect the wires for the relay output if SWITCH being used to the terminals on the FA260RF s PC board 6 Reattach the keypad to its case back 7 Remove the clear protective films from the LCD display and install the keypad labels as required NOTE Upo
4. the FA260RF This user code must also be programmed into the control panel e You must set the House ID only if you are using RF keypads and or bi directional devices AND the House ID Source is the FA260RF Local FA260RF Application Guide Below is a guide that outlines how to program the wireless keys RF receiver and the House ID in the FA260RF for your particular installation Control Panel Are you using RF keys beyond RF receivers RF keypads and or Program Program House ID system s beyond system s Bi directional Wireless Keys RF Source capacity capacity devices on more As Receiver As than 1 partition FA110C FA120C Disable Local 0 FA142C FA148C NO NO N A Use Programming Without Local Wireless Keys YES NO N A Local Enable 1 System 1 YES YES N A Local Disable 0 Local 0 FA162C NO NO NO Use Programming Without Local Wireless Keys YES NO NO Local Enable 1 System 1 YES YES NO Local Disable 0 Local 0 NO YES YES System Disable 0 Local 0 YES YES YES Local Disable 0 Local 0 FA1220CV NO NO NO Use Programming Without Local Wireless Keys FA1340C YES NO NO Local Enable 1 System 1 FA1600CA YES YES No Local Disable 0 Local 0 NO YES YES System Disable 0 Local 0 YES YES YES Local Disable 0 Local 0 Two FA260RFs are needed for this application One connected to partition 1 s keypad terminals and one connected to partition 2
5. will automatically exit the Program mode if no keys are pressed for 30 seconds While in the Program mode e Pressing the key stores the information displayed then moves you to the next prompt and the keypad beeps twice e Pressing the key erases the current information and moves you back so you may enter the correct information Enter a program address e g press 1 for Keypad Address 2 for Receiver Address to set the parameters in the FA260RF The following chart lists the program addresses the keypad display and the choices Program gee Address Description Display Choices Default 1 Keypad Address cA 01 31 31 2 Receiver Address rA 00 30 00 3 House D hl 01 31 4 House ID Source hS 1 System 1 System 0 Local 5 Wireless Key Editing d Enter Existing Device Number 6 Receiver Enable r 1 On 0 0ff 1 Enable 7 Transmitter Module Enable tE 1 On 0 Off 1 Enable 8 Wireless Key Auto Enroll d Enter Serial Number 8then2 Wireless Key User Code u4 Enter 4 Digit User Code 8 then 4 Wireless Key Loop Function Ln Enter Loop Number then Loop2 1 Disarm Function See Wirdess Loop 3 2 Arm Away Key Function Chart Loop 4 3 Arm Stay 8 then 5 Wireless Key On Board o Enter Loop Number then Loop 1 Close for 2 Relay Assignment Relay Action Seconds 9 Restore Defaults EE 1 Restores Defaults Any Other Key Does Not Restore Defaults 0 High Security Mode En 1 Enable 0 Disable 0 Di
6. 260RF is shipped with the loop functions pre programmed Perform steps 6 through 10 only if it is necessary to change any of the loop functions Loop 1 ClosetheFA260RF On Board Rday for 2 sec Loop2 1 Disarm Loop3 2 Arm Away Loop 4 3 Arm Stay See the Wirdess Key Function Chart below for the choices Wireless Key Function Chart Function Entry Disarming Arming Away Arming Stay Arming Maximum Away Instant Arming Instant N BR OO Pp AH Panic Alarm 99 Produces type of alarm amp programmed in control panel Manually Start a Relay Action 7 FA142C 7 n FA162C 8 FA142C 8 n FA162C 71 FA1220C FA1220CV FA1340C 72 FA1220C FA1220CV FA1340C 0 FA1220C FA1220CV FA1340C Manually Stop a Relay Action Activate Relay as Programmed in Control Activate Relay as Programmed in Control Activate Access Control Relay for Partition n Device Number programmed in FA162C to be controlled Press the key Flashes Ln Once the loop number is entered alternately flashes L with the loop number and the present function Default Loop Functions Loop 4 Arm STAY Disarm Loop 1 Close on board relay for 2 seconds Loop 2 Disarm Loop 4 Arm STAY Loop 1 Close on board relay for 2 seconds Loop 3 Arm AWAY SET HOUSE CODE 5804BD 5804BDV Repeat step 6 for the rest o
7. K4456V1 8 00 First FA260RF f fAlert _ Keypad Transceiver Ww PROFESSIONAL SECURITY SYSTEMS INSTALLATION INSTRUCTIONS About the FA260RF The FA260RF is a combination unit that contains e A FA260KP Fixed Addressable Keypad e A 5800TM Transmitter Module e A 5881M RF Receiver e A normally open relay output The FA260RF Keypad Transceiver may be used on any control panel that supports the FA260KP Keypad e g FA110C FA120C FA142C FA148C FA162C FA1220CV FA1340C FA1600CA Features of the FA260RF Wireless Features U L The following transmitters are not intended for use in UL installations 5804 5804BD 5804BDV 5804E and 5827BD e Supports up to 8 wireless keys locally programmed directly into FA260RF without occupying any zones supported by the control panel e Supports button type transmitters 5804 5804BD for local operation e Supports a maximum of 16 transmitters programmed into any 5800 Series supported control panel e Annundates low battery indications for the local wireless keys e Supports wireless keys with Signal Sentry high security 5804E e Provides a nominal range of 200 for the RF transmitters some transmitters have a shorter range e Supports RF jam detection when the receiver is enabled e Provides wireless key support for control panels that do not support RF themselves FA110C Programming Features e Provides an Auto Enroll mode for programming of the wireless keys e Provides a meth
8. ber the device number and Note If all 8 devices have b n enrolled the FA260RF beeps three times and continues to alternated y flash oo and 3 Press any button on the wireless key to enroll the serial number Alternately flashes d with Note f enrolling a wirdess key 5804E in High Security mode the device number and the press all four buttons on the wireless key simultaneously serial number 4 Press the key to accept the serial number OR press the key If you accept the serial to reject the serial number number the display flashes If you accept the serial number the FA260RF beeps twice If you the device number and a reject the serial number the FA260RF returns to the enroll serial hyphen number prompt If you reject the serial Note A maximum of 8 wireless keys may be enrolled into the number the display FA260RF These wirdess keys DO NOT occupy any zones alternately flashes d with supported by the control the device number and If you are finished programming for now press to exit Otherwise continue with step 5 5 Enter 2 User Code Enter the 4 digit user code for the wireless Flashes u4 Once the 4 digit user code is entered the display flashes u4 the first two digits and then the last two digits of the user code Otherwise continue with step 6 Step Action Display Enter 4 Loop Functions Enter the loop number 1 4 Note The FA
9. determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures If using an indoor antenna have a quality outdoor antenna installed Reorient the receiving antenna until interference is reduced or eliminated Move the radio or television receiver away from the receiver control Move the antenna leads away from any wire runs to the receiver control Plug the receiver control into a different outlet so that it and the radio or television receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user or installer may find the following booklet prepared by the Federal Communications Commission helpful Interference Handbook This booklet is available from the U S Government Printing Office Washington DC 20402 The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User s Manual Unauthorized changes or modifications could void the user s authority to operate the equipment LIMITED WARRANTY Pittway Corporation and its divisions subsidiaries and affiliates Seller 165 Eileen Way Syosset New York 11791 warrants itsFirst Alert products to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and servic
10. e for 36 months from the date stamp control on the product or for products not having a date stamp for 30 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period in which case the shorter period shall apply Seller s obligation shall be limited to repairing or replacing at its option free of charge for materials or labor any product which is proved not in compliance with Seller s specifications or proves defective in materials or workmanship under normal use and service Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than First Alert factory service For warranty service return product transportation prepaid to First Alert Factory Service 170 Michael Drive Syosset New York 11791 THERE ARE NO WARRANTIES EXPRESS OR IMPLIED OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER S OWN NEGLIGENCE OR FAULT Seller does not represent that the products it sells may not be compromised or circumvented that the products will prevent any personal injury or property loss by burglary
11. f the loops of the wireless key To program a button on the wireless key to control the on board relay enter 5 On Board Relay Assignment Flashes o Enter the loop number of the wireless key 1 4 Enter the relay action 0 no action 1 relay off 2 relay on 3 relay toggles on and off 4 relay closes for 2 seconds Note The relay action must be 0 for UL installations Press the key Flashes o and the loop number Once the action is entered displays o and alternately flashes the loop number and the relay action 10 Repeat step 9 for the rest of the loops 11 When all loops have been programmed for the wireless key press the key Flashes d followed by the device number 12 The FA260RF automatically displays the next available device number one that does not have a serial number If you want to program additional wireless keys repeat steps 3 through 10 Otherwise press the key This takes you back to the main display which alternately flashes oo and 13 Enter 0 High Security Mode To put the system into High Security mode enter 1 Enter 0 to disable En 14 Press to exit the FA260RF Program mode Note Upon exiting the Program mode the FA260RF alternately flashes Ad the 2 digit keypad address and the 2 digit receiver address If either of these is incorrect repeat steps 1 through 3 i
12. n power up or exit of the Program mode the FA260RF alternately flashes Ad and the 2 digit keypad address and the 2 digit receiver address on the display Press any key to display the system status Figure 1 FA260RF Wiring Connections FA260RF Programming The FA260RF is shipped with pre programmed default values Below is a chart showing these values Later in these instructions are diagrams showing the wireless keys loops and their default functions Regardless of which wireless key you use even if it is one not shown loops 1 4 are defaulted for all 8 devices as shown These values may be changed to suit the installation Entering Program Mode Press the 1 and 3 keys simultaneously for a few seconds within 30 seconds after applying power or within 30 seconds after removing the case back The keypad beeps 3 times and two dashes and two Zeroes flash alternately in the upper left hand corner of the display If any other numbers or letters flash in the display press the key Pressing the 1 and 3 keys 30 seconds or more after applying power allows you to enter the User mode This mode provides a means to enable and disable individual local wireless keys useful if e g a user accidentally loses a wireless key See the User Guide for procedure instructions Programming Operations Once you have entered the Program mode you may move to any program address simply by entering the program address number The FA260RF
13. n the Programming for an Installation Without Local Wirdess Keys section Deleting Replacing or Editing Wireless Keys Use the following procedure to delete replace or change any of the programming for a wireless key Step Action Display 1 Enter the program mode by pressing the 1 and 3 keys simultaneously for a few seconds within 30 seconds after applying power Alternately flashes oo and two dashes Enter 5 Wireless Key Editing Enter the device number for the wireless key you want to edit This must be a device that has its serial number programmed in the FA260RF already To delete the serial number press then press 9 then press gt again To exit without deleting the serial number press the key Press the key to continue Flashes the device number and a hyphen Once the device number is entered alternately flashes d with the device number and the serial number To change any of the programming for the wireless key perform one of the following step in the Programming for an Installation WITH Local Wirdess Keys section e For the user code perform step 5 e For the loop functions perform steps 6 and 7 e For the on board relay assignment perform steps 8 to 9 Alternately flashes d with the device number and When you have completed editing the wireless keys press the key twice to exit the Program mode Note U
14. nel Sounder Speaker fire alarm is loud pulsing tone 200 nominal burglary audible panic alarm is continuous tone FOR DETAILS ON THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL PANEL WITH WHICH THIS DEVICE IS USED FCC STATEMENT This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation FCC ID CFS8DLFA260RF FEDERAL COMMUNICATIONS COMMISSION FCC Part 15 STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use The FCC requires the following statement for your information This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be
15. od for deleting a serial number and re enrolling a new one in its place e Provides default settings for the functions of the wireless keys Additional Features e Provides tamper protection that causes the system to annunciate a trouble condition if the cover is removed or the unit is removed from the wall If supported by the control panel The tamper switch has not been evaluated for UL installation e Can send status signals Armed Ready etc to bi directional units such as 5804BD 5804BDV and 5827BD e Can operate the on board relay in conjunction with the receiver e g to trip a garage door opener e Can activate relays programmed into the control panel e Provides an End User mode to enable disable local wireless keys e g if a user accidentally loses a wireless key See the User Guide for the procedure Application Guidelines for the FA260RF Use the following guidelines when planning an installation e Local wireless keys are programmed directly into the FA260RF and may be used regardless of whether the RF receiver is enabled or disabled e If using bi directional devices be sure to enable the transmitter module in the FA260RF e If transmitters are programmed into the control panel be sure to enable the receiver Make sure you do not exceed the number of receivers the control panel supports e Ifa local wireless key is programmed to arm disarm or to trigger a relay on the control panel a user code must be entered into
16. pon exiting the Program mode the FA260RF alternately flashes Ad the 2 digit keypad address and the 2 digit receiver address If either of these is incorrect repeat steps 1 through 3 in the Programming for an Installation Without Local Wirdess Keys section Troubleshooting The following error messages cause the FA260RF to produce rapid beeps for 5 seconds The table below describes the error messages and the corrective actions Display Probable Cause Corrective Action Lb Low battery in the wireless 1 Replace the battery if the wireless key has a replaceable key battery 2 Replacethe transmitter if the wireless key does not havea replaceable battery Oc Open circuit Verify that the Data Out DO wire is connected properly 1C Incompatible connection Verify that the control panel is not An ADEMCO type control panel Check 09 1 FA260RF Receiver is 1 Verify that the Data In DI wire is connected properly not communicating 2 Another device on the 2 Verify the wiring connections between the control and all keypad terminals is other devices not communicating to the control panel Specifications Physical Wiring Range 6 9 16 H x 4 7 8 W x 1 1 4 D Frequency 345 MHz 166 68mm x 123mm x 31 75mm Current Standby 105mA 12VDC Backlighting on and Ground Sounder on 175mA DO Data out from Control Panel Relay Normally Open 1A 28VDC DI Data in to Control Pa
17. sable When operating the system in High Security mode non encrypted wireless keys will still function If you want only the encrypted wireless keys to operate be sure to delete all non encrypted keys from the system Defaulting the FA260RF To restore the FA260RF to the default values perform the following steps Step Action 1 Enter the Program mode by pressing the 1 and 3 keys simultaneously for a few seconds within 30 seconds after applying power The keypad alternately flashes 00 and two dashes Press the 9 key The display flashes EE Press the 1 key to restore the default values or press any other key to exit without restoring the default values If you pressed 1 the keypad beeps 3 times and returns to alternately flashing 00 and two dashes If you pressed any other key the keypad does not beep and returns to alternately flashing 00 and two dashes 4 Press to exit the FA260RF Program Mode Programming Procedure This section is divided into two parts e Programming for an installation WITHOUT local wireless keys e Programming for an installation WITH local wireless keys Using this programming procedure is necessary only if you plan to use wireless keys beyond the control panel s capacity or on a system that does not support 5800 Series wireless Refer to the FA260RF Application Guide on page 2 for installations that require these
18. sary for this application Upon exiting the Program mode Programming for an Installation WITH Local Wireless Keys the FA260RF alternately flashes Ad the 2 digit keypad address and the 2 digit receiver address If either of these is incorrect repeat steps 1 through 3 e The FA260RF is supplied with default settings for the functions of the wireless keys See page 3 e f during the programming of the wireless keys you make a wrong entry and want to reprogram a wireless key simply press the key until d is displayed Then enter the correct information Perform steps 1 6 in the Programming for an Installation Without Local Wirdess Keys section Then perform the following steps key Note The user code must bea valid code that is programmed in the control pand Press the key to accept the user code If you are finished programming for now press to exit Step Action Display 1 Enter 3 House ID Enter the 2 digit House ID for the FA260RF Alternately flashes hl and a 01 31 2 digit number Note The House D is needed only if RF keypads and or bi directional units are used and HouseID sourceis set for Local The Housel D entered here MUST match the House D programmed in the RF keypad and the bi directional unit Press the key to continue 2 Enter 8 Wireless K ey Auto Enroll The FA260RF automatically Alternately flashes d with advances to first available device num
19. settings Note See the control panel s installation instructions for the acceptable keypad and receiver addresses e f you are using a wireless key in High Security mode 5804E in the control panel it will occupy one of the devices in the FA260RF e When operating the system in High Security mode non encrypted wireless keys will still function If you want only the encrypted keys to operate be sure to delete all non encrypted keys from the system Programming for an Installation WITHOUT Local Wireless Keys To program the FA260RF for an installation without any local wireless keys perform the following steps Step Action Display 1 Enter the Program mode by pressing the 1 and 3 keys simultaneously for a few seconds within 30 seconds after applying power or within 30 seconds after removing the case back Alternately flashes oo and two dashes Enter 1 Keypad Address Enter the 2 digit keypad address 01 31 Press the key to continue Alternately flashes cA and the 2 digit keypad address Enter 2 Receiver Address Enter the 2 digit receiver address 00 30 Press the key to continue Alternately flashes rA and the 2 digit receiver address Enter 4 House D Source Enter 1 System to use the House D programmed into the control panel if RF keypad s and or bi directional device s e Are used on the control panel OR e Neither is used Enter 0
Download Pdf Manuals
Related Search