Remote control
Contents
1. From OPTION MENU enter into PVR File System as below A OSD Language English Audio Languages UK Subtitle Languages UK Country UK PVR File System Restore Factory Default SDE A Automatic Power down 4h Home shop mode v 200 E Select Disk Check PVR File System Start USB Disk Format Time Shift Size Speed Free Record Limit 6 Hr Oke lt MENU Select Disk select which disc to save the record file Select Disk Check PVR File System check if the PVR File System set up in the USB device or not Format File System Size PVR File System Size All SD 104 Mins HD 29 Mins File System Size PVR File System Size All SD 104 Mins HD 29 Mins Suggest to format the device by High Speed Fs which can speed up the record Format disk Warning All data will be lost Do not unplug USB device Formatting please wait below menu appear after Format finish Select Disk CE Check PVR File System Checking USB Disk Pass Format Pass Time Shift Size All Speed Checking Free Record Limit 6 Hr 4 MENU Select Disk Check PVR File System SUCCESS USB Disk Format Pass Time Shift Size All Speed HD support 2048 KB s 6 Hr Pass Free Record Limit X MENU If you select the Hi Speed FS format mode then you can change the time shift size Time Shift Size Time Shift Disk Size 512 MB SB 14 Mins HD 4 Mins 2 Record the program As playing t2. television cabinet slots or openings Never spill any kind of liquid on the television receiver Caution Do not block the ventilation holes in the back cover Adequate ventilation is essential to prevent failure of electrical components Caution ZN Do not trap the power supply cord under the television receiver Caution N Never stand on lean on or suddenly push the television or its stand You should pay special attention to children Serious injury may result if it should fall a a Caution Do not place your television on an unstable cart stand shelf or table Serious injury to an individual and damage to the television may result if it should fall Caution ZN When the television receiver is not used for an extended period of time it is advisable to disconnect the AC power cord from the AC outlet Minimum distances 10cm ecm OL a Caution If the television is to be built into a compartment or similar enclosure the minimum distances must be maintained Heat build up can reduce the service life of your television and can also be dangerous P04 Safety and warnings Introduction CAUTION Never tamper with any components inside the TV or any other adjustment controls not mentioned in this manual All LED TVs are high voltage instruments When you clean up dust or water drops on the LED PANEL or CABINET the power cord should be pulled out from the r
3. Adjust sound level In MENU adjust the item that you Selected 5 STANDBY Rear Side Sockets e O Q Q ope m 4 COMMON INTERFACE Cl lt gt O HDMI1 USE PC AUDIO SCART VGA ANT D ay 12 C 1 AV input 7 USB input 2 L RAUDIO input 8 PCAUDIO input 3 AC Power Source input 9 COMMON INTERFACE CI Intput 4 YPbPr input 10 SCART Intput 5 HDMI2 input 11 VGA Input 6 HDMI input 12 ANT input POY CONNECTING YOUR TV ANTENNA CONNECTION Connect your aerial to the back of the TV into the ANT IN socket IMPROVE YOUR SIGNAL To improve picture quality in a poor signal area use a signal amplifier not supplied CONNECT YOUR PC TO THE TV You can use your TV as a monitor for your personal computer by connecting it with a VGA cable not supplied E Read your computer user guide and check it has a VGA connector BH turnthe power off on your TV and PC B connect aD type 15 pin VGA interface cable to the VGA video interface connector on the PC Connect the other end of the cable to the PC interface connector on the TV Tighten the screws on the VGA connectors and connect the audio cable not supplied to the audio input socket on the back of the TV O turnonthe power of the TV firstly and then the PC 5 Press the button on the TV or TV remote control to set the video input mode to VGA once the image
4. OPTRA ULGO UG OPRARAAOLOEGO CGE OO ogota GOUGU HUGGER EGU DAU HCSGCSTOVTTSUAGSgOSE OPT OVT OOOH o o o o o o o o 00000000000000000000000 00000000000000000000000 00000000000000000000000 D0000000000000000000000 DOOODOCOOOOOUEANNMMIMI 100000000000I00000000000000 OOUCOOOOOOUODAGBOLMMIUI 100000000000000000000000000 B 10080069808088990000000 190G0040009000ea000s0000000be a D 00ee980898699088960N008 100909800990980eg00ev000000p0 a J T T 3 Use the four screws provided to fix the TV onto a wall mounting bracket not included via the four VESA standard holes on the back of the television epee ett penta ty ipa f i j o OOOODODOOOOODAD0OENIMI A000OODOO0OOOONOUOOOODONAONO ery 10800000086 000000080000 NNG0000000c09D000ce0D0000pe P O08 Introduction Front control panel SOURCE MENU CH CH VOL y ooog VOL O00 0 0100 STANDBY 1 Remote control sensor 1 SOURCE Display theinput source menu i l 2 MENU Display main MENU 2 Indicator LED 3 CH CH In TV mode press CH or CH to change BLUE POWER ON RED STAND BY the channel up and down In MENU press CH or CH to select items 3 Key board In standby mode it can Turn on the TV 4 VOL VOL
5. may be compatible but itis not guaranteed to work e SanDisk Extreme Contour USB Flash Drive 8GB SDCZ8 8192 E75 e SanDisk Extreme Contour USB Flash Drive 16GB SDCZ8 016G A75 e Kingston DataTraveler 410 USB 2 0 Flash Drive 8GB DT410 8GB e Kingston DataTraveler 410 USB 2 0 Flash Drive 16GB DT410 16GB e OCZ Technology Rally2 USB 2 0 Flash Drive 4GB OCZUSBR2DC 4GB e OCZ Technology ATV USB 2 0 Flash Drive 8GB OCZUSBATV 8GB e OCZ Technology Rally2 USB 2 0 Flash Drive 8GB OCZUSBR2DC 8GB e SAMSUNG HM500JI 500G 8 This feature is not available for all digital TV such as scrambled or audio only channels P 20 Operation 10 USB Player Press lt gt to select the function icon press OK button to confirm the function Press v or EXIT button to exit the control bar NOTE You can adjust the audio track or program in the Info menu while Playing the video file Choose the Info icon and press OK can display the Info MENU Press source key and selsct USB in soure list press OK button to enter the USB menu Sample1 ts Resolution 720x576 AudioTrack lt 1 2 Subtitle 1 3 Please make sure that the USB device have plugged in the slot There are four type media item can be selected such as photo music E Movie and text Select the type media item by a RTE pressing lt gt press OK button to enter the disk selection menu Program 1 6 USB playback is supported for the following p
6. shows if there is noise present change the VGA mode to another resolution change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear CONNECT A DVD PLAYER OR VCR TO YOUR TV There are two ways in which you can connect a DVD player or VCR to your TV Make sure that both the TV and DVD player or VCR are switched off before you connect them E Connect the AV DVD VCR outputs to the AV IN socket on your TV E Connect the AV audio L amp R to the audio input 8 Press the SOURCE button on the TV to set the video input mode to AV SCART INPUT 1 Connect the scart lead from the external device DVD player Set top box or games console to the TV scart socket Press the SOURCE button to select SCART mode Press the PLAY button on the external device HDMI input 1 Connect the cable from the HDMI device to the TV HDMI socket 2 Press the SOURCE button to select HDMI mode E Refer to the HDMI device user guide for how to operate P10 Introduction COMMON INTERFACE The common interface Cl slot is designed to accept the conditional Access CA Module and Smart card in order to view the pay TV programmes and additional services Contact your Common Interface service provider to get more information about the modules and subscription Please noted that CA modules and smart cards are neither supplied nor optional accessories from us amp War
7. Haier LED LCD TV RECEIVER USER MANUAL MODEL LET26C400HF LET32C400HF LET32C400H Please read this manual carefully before using LET26C430F your television and keep this manual in a good LET32C430F place for future reference ET32C500F Contents Safety and warnings Welcome Pre rrrrrr re rrr reer err errr reer ee ee ee ee ee ee eee eee ee ee ee eee eee ee P02 Important information Perr err rrr rrr rrr rrr rrr rrr errr rr re eee eee ee ee ee ee ee ee ee er eee P02 Warnings and cautions e eeeeeeceeececececeecceeccecoccocooooooocoocoococcoccoecceccecceee P04 Introduction Main Parameter POOP eCe Terre reer eer ee reer rere err ee Tee ee eee eee Te eee eee eee eee ee ee eee ee eee ee P05 Base Stand Assembly Instruction eee ccrrccccc ccc cccccccec cesses cesses cescesceeceecesces P 07 Wall mounting installation guidelines oo coe cee cee coe cee cee cee cee cee cee cee vee P08 Front panel Cee e creer rer ee reer eer ee reer eee eee ees ees eee eee eee ses ses see ses ses ses ses sessessesees P09 Rear AV connections ceccccooooooococosocococoooocococococoocooocococooooocoooocoooooooooo P09 Connecting your TV cecocooosoococoooooosoococoocososcccocoooososoococoocoooooooccooooooooooo P10 Common interface ceececcecococcocococoococoococoocococcococoescococoeccocoococococcococeococoo P11 Remote Control Remote Control EEEE E E E E E E E E E A P 1 2 Operation Installation Guide cscooossooooosoosoossooossssccocosssocosoossoocososoocooosocsososoooc
8. OTE e The format process will take at least 2 minutes Please do not turn off the power or remove the USB device during formatting e During formatting a speed test will be done on the USB device If it fails it means the USB device may not support the Time Shift function Record a paused DTV program to USB storage device 1 While in the DTV input source insert USB storage device to the USB port on the side of your TV 2 Press PAUSE 3 to start Time Shift function The TV program paused The Time Shift OSD appears and starts recording 3 Press STOP 29 to stop Time Shift function and stop recording program SS SSNS Time Shift limitations 1 When the Time Shift feature is activated only the PLAY PAUSE STOP FWD REV VOL VOL MUTE keys and some basic operation keys ENTER EXIT navigation keys are available 2 Video playback may not be smooth and skip if USB recording speed does not meet the minimum requirements 3 Do Not remove USB disk or switch off the power during Time Shift operations It will abort once the signal is lost 4 Do Not remove the signal source during Time Shift operations 5 Do Not quickly and repeatedly change operations between PLAY PAUSE FWD REV 6 Video may become pixelated when Video bit rate is too low 7 Not all USB devices are compatible The USB hard disk drive electricty should be lt 500MA Below is alist of recommended USB drvies Models that are not listed
9. Other source have no scart output signal P 24 Haier
10. UCT j CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK AND FIRE DO NOT PUT THE TV SET NEAR SOURCES OF HUMIDITY DO NOT USE ANY ABRASIVE CLEANERS WHICH MAY SCRATCH OR DAMAGE THE LCD SCREEN AVOID CONTACT WITH OBJECTS THAT MAY SCRATCH THE LCD SCREEN NOTE SERVICING THE UNIT YOURSELF IS UNAUTHORISED AND COULD LEAD TO INJURY OR PRODUCT DAMAGE REFER ALL SERVICING TO THE CUSTOMER HELPLINE P0O2 Safety and warnings SAFETY NOTICE e Warning To reduce the risk of electric shock do not remove the cover or back There are no user serviceable parts inside Refer servicing to qualified personnel e Warning To prevent fire or electric shock hazard do not expose the unit to rain or moisture e Do not expose the Adaptor and product to water dripping or splashing and no objects filled with liquids such as vases should be placed on the unit e Keep the product away from direct sunlight and heat source such as radiators or stoves e Do not block the ventilation openings Slots and openings on the unit are provided for ventilation The openings should never be blocked by placing your product ona cushion sofa or other similar surface Donot place the product on unstable cart stand tripod bracket or table The unit may fall resulting in possible damage or injury e Never place heavy or sharp objects onthe panel or frame e Only use the AC adapter included with product Using any other adapter will void your warranty e
11. Unplug the po wer from the outlet when the unit is not in use e Attention should be drawn tothe environmental aspects of battery disposal e WARNNING The battery battery or batteries or battery pack shall not be exposed to excessive heat such as sunshine fire or the like e WARNNING Excessive sound pressure from earphones or headphones can cause hearing loss e WARNNING Only use attachments accessories specified provided by the manufacturer the product is supplied by AC adapter the AC adapter is used as disconnect device the disconnect device shall remain readily operable P O3 This marking indicates that this product should not be disposed with other household wastes throughout the EU To prevent possible harm to the environment or human health from uncontrolled waste disposal recycle it responsibly to promote the sustainable reuse of material resources To return your used device please use the return and collection systems or contact the retailer where the product was purchased They can take this product for environmental safe recycling WARNINGS AND CAUTIONS Warning High voltages are used in the operation of this television receiver Do not remove the cabinet back from your set Refer servicing to qualified service personnel Warning N To prevent fire or electrical shock hazard do not expose the television receiver to rain or moisture x Warning N Do not drop or push objects into the
12. ble or enable the sound output AUDIO To select the available audio language of TV programs RECALL To access the previously viewed channel SOURCE To select input source OK To confirm selection EXIT To return to the previous menu orexit menu SOUND To switch sound mode CH CH To access the next or previous channels ASPECT To change picture aspect ratio TV RADIO In DVB mode itis used to switch between digital TV channels and radio stations Display remove the programme information TEXT To enter or exit TELETEXT INFO To display information about the channel being viewed or further information about the program when in small EPG screenin DTV mode SUBTITLE To switch between different subtitles in DTV mode Oe 63 D 03 Remote Control To skip to the next file in USB mode To skip to the previous file in USB mode REC REP Press to record the TV program you i are watching in DTV Mode or press to repeat play in USB Mode 1 Remove the battery cover 29 Stop the media player in USB mode 2 Inserting the 2 AAA 1 5V batteries making sure the polarity or of the batteries matches 30 To scan in reverse during USB USB playback 3 Mount the battery cover Replace with new 32 Play the media player in USB mode batteries when the TV set begins to show the 33 Pause the media player in USB mode time sh
13. e Shop Mode freely by yourself 1 CHANNEL MENU The first item of the MENU is channel menu for TV or DTV source only A Auto Tuning DTV Manual Tuning i ATV Manual Tuning Programme Edit lt CHANNEL h Signal Information gt CI Information Software Update OAD Off Software Update USB v 2 a J O B You can search channels and edit programs here 1 Auto tuning Search all the channels automatically you can select ATV and DTV 4 Tune Type DTV ATV A Netherlands Portugal MENU OKO Pls press 4 gt VA to select country at first then press OK button to start auto tuning Channel Tuning TV 0Programme s DTV 0 Programme s Radio 0 Programme s 96 UHF CH 68DTV TTT TTT NOTE All the channels including ATV DTV and Radio can be tuning by one time if the Tune Type is DTV ATV All the stored channels will be disappear after auto tuning After auto tuning the channel will skip to the first DTV channel 2 DTV Manual tuning You can select a DTV channel then find the program in this channel Pls press 4 gt to select the channel or input channel Num by Num key then press OK to search the programs NOTE Bad Normal Good means signal intensity DTV Manual Tuning lt j VHF CH 5 gt Press OK to search Bad Nomal Good BEER EERE ERR eee 3 ATV Manual tuning You can change the sound system to search the analog TV channels and fine tune the cha
14. eceptacle then wipe the TV with a dry soft cloth During thunder and lighting unplug the power cord and antenna cord to prevent damage to your TV All repairs to this TV should only be performed by qualified TV service personnel Main features 1 Used as Television display terminal PC display 2 High luminance wide viewing Angle 3 Time shift Main parameter INSTALLATION Locate the TV in the room where light does not strike the screen directly Total darkness or a reflection on the picture screen can cause eyestrain Soft and indirect lighting is recommended for comfortable viewing Allow enough space between the TV and the wall to permit ventilation Avoid excessively warm locations to prevent possible damage to the cabinet or premature component failure Do not cover the ventilation openings when using the TV 4 HDMI interface and SCART Interface 6 NICAM TV System PAL B G 1 D K SECAM B G D K L L Video Signal System PAL SECAM Input Power Voltage AC 100V 240V 50 60Hz Audio Output Power THD lt 7 2x5W 2x8W Signal Input Analog RGB PC x1 PC audio x1 High Definition Multimedia Interface HDMI x2 Video Input x1 Audio Input x1 Y Pb Prx1 Mini SCARTx1 CIx1 USB x 1 Tuner x 1 Composite Video input gt 350 Horizontal definition TV line YPbPr POS gt 400 PC PRESET MODE RESOLUTION V Freq Hz H Freq KHz 640x480 800x600 1280x1024 1920x1080 E
15. eration 4 Remind Press the blue key to choose one program and set up one reminder time the TV screen will skip to the choosed program in the reminder time automatically Reminder setting oa so2sztTvmo3 gt 08 Minute 05 Hour Apr Month 28 Date Once Mode OROI 8 PVR function 1 Prepare to record the program From OPTION MENU enter into PVR File Systemin OPTION MENU please choose check PVR File System Click OK until checking change into Success Note please check the term speed If it is HD support that means the speed of USB device is available for time shift and record If not please format the device to make sure the device available The default Free Record Limit is 6 hour if the space on the disk is big enough If the space is not big enough the record time should be shorter depends on the room on the device During the check PVR File System checking please do not take any other operation until it finished The recordings have to be done with TV PVR system It can only be played in the same TV notin other kind of devices computer DVD etc which doesn t be compatible with TS Format See that in order to carry out any kind of recording the TV will oblige you to format the connected device to store the recording WARNING WHEN YOU FORMAT THE EXTERNAL DEVICE WILL LOSE ALL THE FILES AND INFORMATION YOU STORAGE IN THE DEVICE
16. group is created you can press the FAV key to quickly access your favorite channel 5 Cl information optional This menu can display the Cl card s information 2 PICTURE MENU The second item of the MENU is PICTURE MENU You can adjust picture effect here such as contrast brightness etc Press OK to move press OK to adjust P15 A Picture Mode Standard Color Temperature Aspect Ratio lt PICTURE m Noise Reduction Screen vy a J O E amp Picture Mode Standard Color Temperature Medium Red 40 Brightness 50 Green 31 NOTE 1 Tint is available in NTSC system only 2 There are four colors temperature modes can be selected medium warm cool user 3 Screen is available in PC mode only which can adjust Horizontal position vertical position size and phase 3 SOUND MENU The third item of the MENU is the SOUND MENU You can adjust the sound effect here such as treble bass balance etc Press wa to move press OK to adjust A Sound Mode Standard Balance a Auto Volume lt SOUND Surround off vy 200 EA Note Auto volume only available when the input signal volume is too large or distortion 4 TIME MENU The forth item of the menu is the TIME MENU You can adjust the clock power on off time sleep time etc Press lt 4 gt to move press OK to adjust A Off Time On Time Sleep Timer S TINE Auto Sleep Time Zone y an 0 8 NOTE Within 15 mi
17. he DTV source choose the channel and click record the record frame will pop up Click record again the record frame will disappear and the REC icon still on the left top It will disappear until you click stop 3 Play the record In USB the record program will be saved inthe folder _MSTPVR onthe device 1 The USB storage size needs to be the size between 4GB to 500GB 2 Video may become pixelated when Video bit rate is too low 3 Not all USB devices are compatible Below is alist of recommended USB drvies Models that are not listed may be compatible but it is not guaranteed to work The USB support list are the same as Timeshift function see page 20 P8 04 Operation 9 Timeshift function 1 Prepare to record the program This TV allows you to pause and record the 00 00 33 00 04 22 currently watched digital program toaUSB storage device and to resume to the point ELE E ee ARN REXI cai where it was paused NOTE e Formatting a USB 2 0 storage device will NOTE be needed Save your original data before formatting All the data stored in e Please do not unplug the USB storage the USB device will be erased after device when the Time Shift function is formatting activated e Approximately 4GB of memory buffers USB Drive Storage Format about offer 140 minutes Select to format the USB device and allocate the amount of space for the Time Shift function N
18. hoto file formats _ JPEG JPEG format files with the extension jpg ry BMP files with the extension bmp PNG files with the extension png USB playback is supported for the following music file formats MP3 files with the extension mp3 WAV files with the extension wav USB playback is supported for the following text Press the lt 4 gt to select the right disk and press file formats OK to display media files and folder list or TXT files with the extension txt choose Return to back to the media type selection menu RTT gt USB playback is supported for the following movie file formats AVI file with the extension avi ri i i TS MPEG2 amp H 264 Return Resolution 688x412 AudioTrack 1 2 Subtitle 1 3 Program IS Size 511457 KBytes Movies 3 A Sample1 ts Sample2 ts Sample3 ts Sample4 ts Select the media file by pressing lt gt orwa then the preview frame will pop up Press the button gt to play the media file in full screen When the media file photo music Movie or text type is playing press the OK or Info button can display the control bar 00 00 33 00 04 22 il u id a gt a i Pause FB FF Prev Next Stop RepeatALL Info P2 Hotel Mode Please press source key first and then press number key 1001 to enter into Hotel Mode Hotel Menu Hotel Mode Panel key lock Max volume Start Source Start Chan
19. ift following symptoms Operation is unsteady or in DTV mode erratic Sometimes the TV set does not function with Remote Control Unit Remark 1 Alkaline Battery Recommended 2 Remove batteries when they are exhausted or if the remote control is not to be used for Long time P 12 REMOTE CONTROL TELETEXT Teletext is an information system broadcast by certain channels which can be consulted like a newspaper It also offers access to subtitles for viewers with hearing problems or who are not familiar with the transmission language cable networks satellite channels etc Press TEXT SELECTING A PAGE 399 Y 000 0000 DIRECT ACCESS TO THE ITEMS 0 INDEX SUB PAGE HOLD REVEAL LIST You will obtain This is used to call or exit teletext modes The summary appears with a list of items that can be accessed Each item has a corresponding 3 digit page number If the channel selected does not broadcast teletext theindication 100 will be displayed and the screen will remain blank in this case exit teletext and select another channel Enter the number of the page required using the 0 to 9 up down Example page 120 enter 120 The number is displayed top left the counter turns and then the page is displayed Repeat this operation to view another page If the counter continues to search this means thatthe pageis not transmitted Select another number Coloured are as are disp
20. layed at the bottom of the screen The 4 coloured keys are used to access the items or corresponding pages The coloured areas flash when the item or the pageis notyet available This returns to the contents page usually page 100 Certain pages contain sub pages which are automatically displayed successively This key is used to stop or resume sub page acquisition The indication appears top left To freeze the page To display or hide the concealed information games solutions The user can set four favorite pages to be directly linked to the four color keys While list mode is activated itis not possibility to use TOP or FLOF navigation with the colorkeys The favorite page numbers should be stored and restored to from nonvolatile memory for each channel by the system software P13 O4 OPERATION Installation Guide Mode Select A Norway Rumania Switzerland Morocco Portugal Serbia Sweden NewZealand Algeria v OKOL This screen only appear when the TV first time turn on or reset to factory set You can choose energy saving mode and country auto tuning programs And after tuning the screen will skip to the first DTV program NOTE 1 Home Mode is an energy saving Mode it s recommended as a family s normal watching mode in default by manufacturer 2 Shop Mode adapt to superstore for advertisement show or product presentation otherwise Shop Mode s lightness is high than Home Mode 3 Switch Hom
21. light SEN Volume check if mute is activated or if the audio system eS Normal Picture connections are not correct AW ye Pps antenna position direction Normal audio Power cord is not inserted Power switch is not opened l Contrast and brightness volume No picture setup Press standby key on the remote control for inspecting No colour Pp Normal audio Colour control AWE N Picture retune channel breaking up No colour y Nioiee TVsystem AWD as P23 Trouble shooting Specification Colour system Sound system Video input Y Pb Pr HDMI Power requirements Power consumption Audio output Environment conditions Accessory PAL B G 1 D K SECAM B G D K L L BG DK L L SCART YP bPr AV VGA HDMI USB A480i p 576i p 720p 1080i 1080p 480i p 576i p 720p 1080i 1080p 100 240V 50 60Hz 55W 26 75W 32 2x5W 2x8W Working temperature 5 C 35 C Working humidity 20 80 Storage temperature ISCA Storage humidity 5 90 User manual Remote control Battery x2 Quick start guide The part specifications of this TV set provided here are for reference only Difierences may occur as product technology is updated Design and specifications are subject to change without notice Scart Output description 1 When current source is ATV AV SCART scart output signal is ATV 2 When current source is DTV scart output signal is DTV 3
22. nel Setup Menu display Input source change Save To USB Loading Volume default Hotel Menu Set Hotel mode on off When Hotel mode is set ON these below functions will be unavailable e Auto Tuning Color temperature Balance e Sound mode e Auto Volume e Manual Tuning e Clock Panel key lock Keypad will be locked when Key Lock mode ison Max volume Set max volume limitted This option allows you to set the Max Volume Level 04 Operation Start Source Choose source the options as follow TV Video Component PC HDMI press the lt or gt button to select the desired source Start Channel In TV mode you can select a channel number to be set as the TV present channel Press the lt or gt button to select the desired channel number Setup Menu display Main menu lock main menu will not display when set to No Input source change Source lock you can t change the source when set to No Save To USB Backup all TV setting data to USB disk backup file named DATABASE bin Load Restore this data to TV from USB disk When restore is executed the TV will reboot Volume default Power on default volume press the lt or gt button to select the desired volume pez Trouble shooting Trouble phenomenon Symptom Picture Audio Inspection Check antenna position direction or connection or connection ba electronic equipment car SHE Interference motorcycle fluorescent
23. ning e Switch off your TV before any module is inserted in the Common Interface slot 1 Insert the CAM correctly then Smart Card to the Cl slot that is located at the side of the TV B Turn on the TV and it will display the below message if the CA module is detected Wait for few moments until the card is activated CI Module Inserted E Press the MENU button then press a button to select Cl Information option A Auto Tuning DTV Manual Tuning ATV Manual Tuning P Programme Edit lt CHANNEL a S Signal Information gt CI Information Software Update OAD Off Software Update USB Yy aono gzA EF Detailed information on the CI card in use is displayed B Press OK button to access the card menu Refer to the module instruction manual for setting details When module is removed the following message will appear on the screen CI Module Removed 03 Remote control 1 POWER To set the TV to standby or power on 2 NUMERIC KEY For direct access to channels 3 TV MENU To display TV menu 4 CURSOR To move within the menu 5 CH LIST To display the channels list 6 VOL To adjust sound level 7 PIC To switch picture mode 8 SLEEP Set timer to turn off the TV 9 FREEZE To freeze the picture 10 EPG To display information about the program being viewed and what s on next in DTV mode FAV To access your favourite channels list in TV or DTV mode TELETEXT KEYS Please refer to next page MUTE To disa
24. nnels then storage the channels you selected ATV Manual Tuning lt q Storage To 1 gt System BG Current CH 1 Search Fine Tune Frequency 255 25 MHz Save MENU 04 Operation NOTE Press teletext red button to storage to channels after manual tuning 4 Program edit You can Delete Rename Move Skip FAV any programs O Delete Press teletext red button the program in cursor will delete Rename Only can rename ATV programs Move the cursor to the program press teletext green button to rename the program Press VA to choose the character Press lt 4 gt to move the cursor Press MENU button to exit edit Press EXIT to exit the menu Note ATV programs name only can be 5 character DTV programs name can be 25 character Move Use the Arrow Buttons to select the channel you wish to move Then press the Yellow Button to select Move function Once active use the Arrow Buttons to move and then press OK to confirm Skip Press wa to choose the program press teletext blue button to skip this program The will show on the right side of the program Choose the skipped program press blue button again youcan cancel the skip The will disappear Favourite Press WA to choose the program press FAV button it will show Y on the right side of the program Choose the FAV program press FAV button again you can cancel the FAV the will disappear Once your favorite
25. not search the channels or change any programs A lt Lock L E My Lock System Set Password Block Program Parental Guidance Off gt NOTE The default pass word is 0000 If you forget the password you can use the super password 9443 Block program Press VA to choose the program press teletext green button to block the program If you want unblock the program pls enter the main menu input the password then press green button again Parental guidance Press lt 4 gt to choose rating 7 EPG Menu Electronic Program Guide The EPG menu is used to look at what is being broadcasted on DTV or Radio channel in the day To access the EPG menu press the EPG botton the following menu will be displayed PROGRAMME GUIDE TIME 28 Apr 04 39 800 SZTVM01 801 SZTVM02 802 SZTVMO3 803 SZTVM04 804 Date No Information No Information No Information No Information No Information Record INFO OKOK Schedule Remind INDEX 1 O INFO Use eft to choose the programs Press INFO key you can display the highlight program s information 2 C Schedule Press the teletext yellow key It can list all the reminder schedule presswA to choose the list press red key DELETE to delete the schedule list Schedule List 04 55 28thApr Time Date Programme Title Channel Name 3 Record Press the red key It can set the program to be recorded iP TG 04 Op
26. nutes there is no signal the TV will auto sleep if Auto Sleep is set ON The clock time can get from the DTV system auto 5 OPTION MENU The fifth item of the MENU is the OPTION MENU You can adjust the Menu language Audio language Subtitle language etc A Audio Languages UK Subtitle Languages UK Country UK PVR File System Restore Factory Default Automatic power down 4H Home Shop Mode lt ornion dj vy S a JOA NOTE 1 Within 4 hours there is no action TV will appear the countdown reminder window on the last 150 seconds once times up TV will go standby automatically 2 Press any key will cancel this action Reminder window is belowing Automatic Power down 4h Opening TV for 4 hours without action TV will go standby automatically You will switch ON OFF to open cancel Standby automatically Home shop mode If you select the home mode the Automatic Power down 4h will swith on and if you select the shop mode the Automatic Power down 4h will swith off In PVR File system menu you can set up USB disk for PVR Select Disk Check PVR File System Start USB Disk Format Time Shift Size Speed Free Record Limit 6 Hr MENU 0 X Q NOTE Restore factory default will clear all the programs and password 6 LOCK MENU The sixth item of the menu is the LOCK MENU You can lock system set password block program and set parental guidance Once you set the lock system on you can
27. ossooo P 14 Trouble shooting Trouble shooting cooooocoocosocoococosoooooocoooosococoooocococosoooococooooooooooooooooo P 23 Specification ceecocoecoccococcecoocococcococcoccecosoecocoococcecoscocoesococcecoecosoesoes DP JA PO Safety and Warnings WELCOME Thanks for buying this 26 32 LED LCD TV This guide will help you set up and begin using your TV First check the contents of your box with the parts check list below 26 Full HD 1080P Digital LED LCD TV 32 HD Ready LED LCD TV 32 Full HD 1080P Digital LED LCD TV Remote control Remote control Remote control AAA battery x2 AAA battery x2 AAA battery x2 Instruction Manual Instruction Manual Instruction Manual Quick start guide Quick start guide Quick start guide Scart cable x1 Scart cable x1 Scart cable x1 Now you can get started IMPORTANT INFORMATION READ ALL INSTRUCTIONS BEFORE USE AND KEEP FOR FUTURE REFERENCE CAUTION RISK OF ELECTRIC SHOCK AIN DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE FOR ANY PROBLEMS REFER SERVICING TO THE CUSTOMER HELP LINE THERE IS A LIGHTNING ARROW SYMBOL IN THE TRIANGLE THIS SYMBOL INDICATES HIGH VOLTAGE IS PRESENT INSIDE IT IS DANGEROUS TO MAKE ANY KIND OF CONTACT WITH ANYINSIDE PART OF THIS PRODUCT THERE IS A EXCLAMATION MARK IN THE TRIANGLE THIS SYMBOL ALERTS YOU THAT IMPORTANT LITERATURE CONCERNING OPERATION AND MAINTENANCE HAS BEEN INCLUDED WITH THIS PROD
28. xcept for LET32C400H LET32C430F 31 47 P 06 Introduction Base Stand Assembly Instruction 1 Insert the stand support pillar into the stand as the arrow indicated direction and then fastened with three screws 2 Insert the stand Ass y into back cover as the arrow indicated direction and then fastened with one screw INSTALLATION NOTES Locate the TV ina room where light does not strike the screen directly Total darkness or areflection on the screen can cause eyestrain Soft and indirect lighting is recommended for comfortable viewing Allow enough space between the TV and the wall to permit ventilation Avoid excessively warm locations to prevent possible damage to the cabinet or premature component failure P O7 WALL MOUNTING INSTALLATION GUIDELINES This television can be wall mounted as follows 1 Place the LED LCD Television onto a solid surface Please place some soft material over the front of the screen to protect it from any damage 2 Remove the screws from the lower part of the television where the base joins to the TV and take away the stand put the stand somewhere safe for future use AeA WMH HHH WH A KEM HHH HM i HEH HEH HERE EE tgtg tnt 1g totg goto gogig tgo eg eat eat gt eat eat Opt hey eat ety ttt ootata tat Onte ototo HUGG SGONE
Download Pdf Manuals
Related Search