EF70-200mm f/2.8L IS II USM COPY
Contents
1. l MODE _ lar2 aeee er ml lar2 i E e 1 Set the STABILIZER switch to ON e If you are not going to use the image stabilizer function set the switch to OFF 2 Select the stabilizer mode e MODE 1 Corrects vibrations in all directions It is mainly effective for shooting still subjects MODE 2 It compensates for vertical camera shake during following shots in a horizontal direction and compensates for horizontal camera shake during following shots in a vertical direction 3 When you press the shutter button halfway the Image Stabilizer will start operating e Make sure the image in the viewfinder is stable then press the shutter button the rest of the way down to take the picture ENG 8 7 Tips on Using the Image Stabilizer The image stabilizer in this lens is effective for hand held shots under the following conditions MODE 1 MODE 2 OFF OFF e In semi darkened areas such as indoors or e When panning subjects in motion outdoors at night e In locations where flash photography is prohibited such as art museums and theater stages e In situations where your footing is uncertain e In situations where fast shutter settings cannot be used ENG 9 Tips on Using the Image Stabilizer e The Image Stabilizer cannot compensate for a blurred shot caused by a subject that moved Set the STABILIZER switch to2. s Custom Function to change the assigned button to operate the AF the Image Stabilizer will operate when you press the newly assigned AF button ENG 10 8 Infinity Compensation Mark 9 Infrared Index Infinity compensation mark 15 30 ft 10 15 30 5 10 o0 m 3 5 10 oo 0 70 Distance index To compensate for shifting of the infinity focus The infrared index corrects the focus setting when using point that results from changes in temperature monochrome infrared film Focus on the subject The infinity position at normal temperature is the manually then adjust the distance setting by moving the point at which the vertical line of the L mark is focusing ring to the corresponding infrared index mark aligned with the distance indicator on the distance scale 0 Some EOS cameras cannot use infrared film See the instructions for your EOS camera Q For accurate manual focusing of subjects at infinity look through the viewfinder or look at the E F 5 oe magnified image on the LCD screen while e The infrared index position is based on a rotating the focusing ring wavelength of 800 nm e The compensation amount differs depending on For cameras with Live View shooting capability the focal length Use the indicated focal length as a guide when setting the compensation amount e Be sure to observe the manufacturer s instructions when using infrared film e Use a red filter when you take the picture ENG 11 10 Using th
3. OFF when you are taking pictures using the Bulb setting long exposures If the STABILIZER switch is set to ON the image stabilizer function may introduce errors The Image Stabilizer might not be fully effective in the following cases e You shoot while riding on a bumpy road e You move the camera dramatically for a panning shot in Mode 1 e You shoot using techniques other than following shots in Mode 2 The Image Stabilizer consumes more power than normal shooting so fewer shots can be taken if you use the function The image stabilizer operates for about two seconds even when your finger is off the shutter button Do not remove the lens while the stabilizer is in operation This will cause a malfunction With the EOS 1V HS 3 ELAN 7E ELAN 7 30 33 ELAN 7NE ELAN 7N 30V 33V ELAN IVELAN IIE 50 50E REBEL 2000 300 IX and D30 the Image Stabilizer will not work during self timer operation El Using a tripod also stabilizes the image However depending on the kind of tripod and shooting conditions sometimes it may be better to turn off the Image Stabilizer function The stabilizer is equally effective for hand held photography and photography with a monopod The Image Stabilizer function also operates when the lens is used with the EF12 II EF25 Il Extension Tube and the EF1 4X II EF2X Il Extender Pictures may look distorted after being taken depending on the camera but this doesn t affect Shooting If you set the camera
4. 628 0 23x 0 17x 200mm 998 3404 0 28x 0 06x 7 4 4 42 j EF25 II Omm 00 06 0 42x 0 38x 200mm 862 1740 0 36x 0 14x El Manual focusing is recommended for accurate focusing ENG 13 14 Extenders Sold separately With Extender EF1 4X Il or EF2X Il attached the lens specifications will change as follows Item With EF1 4X Il Extender With EF2X Il Extender Focal length mm 98 280 140 400 Aperture f 4 45 f 5 6 64 Diagonal 25 20 8 50 16 20 6 10 Angle of view Vertical 13 50 4 55 9 10 3 30 Horizontal 20 50 7 20 13 40 5 10 Maximum magnification x 0 30 0 44 Q e First attach the Extender to the lens then attach the lens to the camera Detach it from the camera in the reverse order If you attach the lens to the camera first misoperation may occur e Only one Extender can be attached to the lens and camera e If you use an Extender on the lens mounted on a EOS A2 A2E 5 set the exposure compensation to 1 2 stop for the EF1 4X Il or 1 stop for the EF2X Il El e Autofocusing is still enabled with Extender EF1 4X II EF2X Il attached e When an Extender is attached the AF speed will become slower by design to retain proper AF control ENG 14 Specifications Focal Length amp Max Aperture 70 200 mm f 2 8 Lens Construction 23 elements in 19 groups
5. Canon EF LENS EF70 200mm f 2 8L IS IT USM a Instruction IMAGE STABILIZER AS ULTRASONIC Thank you for purchasing a Canon product Dedicated to EOS cameras the Canon EF70 200mm f 2 8L IS Il USM lens is a high performance telephoto zoom lens equipped with an Image Stabilizer e IS stands for Image Stabilizer e USM stands for Ultrasonic Motor Conventions used in this instruction Warning to prevent lens or camera malfunction or damage Supplementary notes on using the lens and taking pictures Features 1 2 The Image Stabilizer gives the equivalent effect of a shutter speed four stops faster With fluorite and UD lens elements outstanding image delineation is obtained Ultrasonic motor USM for quick and quiet autofocusing Manual focusing is available after the subject comes into focus in autofocus mode ONE SHOT AF A truly round aperture hole results in a nicer background blur The lens is compatible with Extender EF1 4X Il and EF2X II Tight seal structure ensures excellent dust proof and drip proof performance Based on 1 focal length second Generally it requires a shutter speed 1 focal length second or faster to prevent camera shake ENG 1 Safety Precautions A Safety Precautions e Do not look at the sun or a bright light source through the lens or camera Doing so could result in loss of vision Looking at the sun dire
6. Min Aperture Angle of View f 32 Diagonal 34 12 Vertical 19 30 7 Horizontal 29 10 Min Focusing Distance 1 2 m 3 9 ft Max Magnification amp Field of view 0 21 x at 200 mm 308 x 463 115 x 171 mm 12 1 x 18 2 4 5 x 6 7 inch at 1 2 m Filter Diameter 77 mm Max Diameter amp Length 88 8 x 199 mm 3 5 x 7 8 inch Weight 1490 g 52 6 oz Lens Hood ET 87 Lens Cap E 77U Case LZ1326 e The lens length is measured from the mount surface to the front end of the lens Add 21 5 mm when including the lens cap and dust cap e The size and weight listed are for the lens only except as indicated e Aperture settings are specified on the camera All data listed is measured according to Canon standards Product specifications and appearance are subject to change without notice ENG 15 Canon CT1 7586 002 CANON INC 2010 2010 2
7. ctly through the lens is especially hazardous e Whether it is attached to the camera or not do not leave the lens under the sun without the lens cap attached This is to prevent the lens from concentrating the sun s rays which could cause a fire Handling Cautions e If the lens is taken from a cold environment into a warm one condensation may develop on the lens surface and internal parts To prevent condensation in this case first put the lens into an airtight plastic bag before taking it from a cold to warm environment Then take out the lens after it has warmed gradually Do the same when taking the lens from a warm environment into a cold one e Do not leave the lens in excessive heat such as in a car in direct sunlight High temperatures can cause the lens to malfunction This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Do not make any changes or modifications to the equipment unless otherwise specified in the instructions If such changes or modifications should be made you could be required to stop operation of the equipment This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC Rules These limits are designed to
8. e Tripod Mount Adjusting the Revolving Mount You can loosen the orientation lock knob on the tripod mount to allow it to rotate as needed to fit a particular camera model for switching between vertical and horizontal positions Detaching First remove the lens from the camera and then remove the tripod mount from the lens as shown below To attach the tripod mount reverse the procedure 1 Loosen the orientation 2 Rotate the tripod mount and 3 Slide off the tripod collar locking knob align the mounting indicator away from the rear of the on the tripod mount with the lens one on the lens ENG 12 11 Filters Sold separately You can attach filters to the filter mounting thread on the front of the lens Q e If you need a polarizing filter use the Canon Circular Polarizing Filter 77mm e To adjust the polarizing filter first remove the lens hood 12 Close up Lenses Sold separately Attaching a 500D 77mm Close up Lens enables close up photography Magnification will be 0 14x 0 60x El e Close up Lens 250D cannot be attached because there is no size that fits the lens e Manual focusing is recommended for accurate focusing 13 Extension Tubes Sold separately You can attach Extension Tube EF 12 Il or EF25 Il for magnified shots The shooting distance and magnification are shown below Camera to Subject a Distance mm Magnification Near Far Near Far EF1 I 70mm 538
9. g ring The focusing ring always works regardless of the focus mode E After autofocusing in ONE SHOT AF mode focus manually by pressing the shutter button halfway and turning the focusing ring Full time manual focus ENG 5 4 Zooming To zoom turn the zoom ring Q Be sure to finish zooming before focusing Zooming after focusing can affect the focus ENG 6 5 Hood The ET 87 hood can keep unwanted light out of the lens and also protects the front of the lens from rain snow and dust Button Attaching Removing To attach the hood align the hood s attachment To remove the hood hold down the button on the position mark with the red dot on the front of the side and turn the hood in the direction of the lens then turn the hood as shown by the arrow arrow until the position mark on the hood aligns until the lens red dot is aligned with the hood s with the red dot stop position mark The hood can be reverse mounted on the lens for storage Q e Part of the picture may be blocked if the hood is not attached properly e When attaching or detaching the hood grasp the base of the hood to turn it To prevent deformation do not grasp the rim of the hood to turn it ENG 7 6 Image Stabilizer Settings You can use the image stabilizer in AF or MF mode i ON r OFF a a E STABILIZER
10. ns See your camera s instructions for details on Q The lens mount has a rubber ring for enhanced mounting and detaching the lens i water and dust resistance The rubber ring may cause slight abrasions around the camera s lens mount but this will not cause any problems If the rubber ring becomes worn it is replaceable by a Canon Service Center at cost e After detaching the lens place the lens with the rear end up to prevent the lens surface and electrical contacts from getting scratched If the contacts get soiled scratched or have fingerprints on them corrosion or faulty connections can result The camera and lens may not operate properly If the contacts get soiled or have fingerprints on them clean them with a soft cloth If you remove the lens cover it with the dust cap To attach it properly align the lens mount index and the index of the dust cap as shown in the diagram and turn clockwise To remove it reverse the order ENG 4 2 Setting the Focus 3 Switching the Focusing Mode Distance Range SAUER To shoot in autofocus AF mode set the focus You can set the focusing distance range to mode switch to AF 1 2 m 3 9 ft to infinity or 2 5 m 8 2 ft to infinity To use only manual focusing MF set the focus By setting the suitable focusing distance range mode switch to MF and focus by turning the the actual autofocusing time can be shorter focusin
11. provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Consult the dealer or an experienced radio TV technician for help This Class B digital apparatus complies with Canadian ICES 003 ENG 2 Nomenclature Hood mount 7 D TT M Filter mounting thread 13 Focusing ring 5 Focus mode switch 5 Image stabilizer switch 8 m Focusing distance range selection switch 5 Distance scale 11 Zoom ring 6 Rubber ring 4 Lens mount index 4 Tripod mount 12 Orientation lock knob 12 Image stabilizer mode selector switch 8 For detailed information reference page numbers are provided in parentheses ENG 3 1 Mounting and Detaching the Le
Download Pdf Manuals
Related Search