S4 jr jr Zoom User Manual 0107.book
Contents
1. Figure 2 The color frame holder is equipped with a spring loaded retaining clip that prevents color frames and accessories from falling out See Figure 2 WARNING Make sure all color frame accessories are locked in position with the retaining clip before hanging the Source Four Step 1 Release the retaining clip by pushing it sideways while gently pulling backwards Step 2 Insert the color frame 2 Source Four jr jr Zoom User Manual Step 3 Lock the retaining clip by pushing sideways while gently pushing forward o Note The performance of saturated colors may be less than desirable in any theatrical lighting fixture For best results always use high quality color media rated for high temperature use ETC s optional Conical Gel Extender part 7060A1048 will provide maximum color media life Gel Extenders are not recommended for 70 and 90 lens tubes due to the extremely wide angle beam A variety of heat shield products is also available from many color media manufacturers Follow the manufacturer s instructions for the use of these products Replacing the HPL lamp m _ HPL lamp l Lamp retention ali brackets i Lamp retention clip Lamp housing Knurled bolt Figure 3 A lamp must be installed before you use the fixture Note Verify that the HPL lamp you intend to install is suitable for your facility s voltage 115 120 230 and 240 volt HPL lamps are a2. Zoom front focus Figure 1 WARNING Please note the following safety warnings before use Do not mount the fixture on or near combustible surfaces Do not operate the fixture without a lens installed Always hang the fixture with the colour frame retaining clip in the locked position Fixture information HPL lamp table A CAUTION The Source Four jr is rated for 575w maximum lamp Do not use lamps other than the HPL in Source Four fixtures Use of lamps other than HPL or greater than 575w will void your warranty Lamp code Watts Volts Initial Lumen Color temp Average rated life HPL 550 77 550 77 16 170 3 250 300 hours HPL 550 77X 550 77 12 160 3 050 2000 hours HPL 575 115 575 115 16 520 3 250 K 300 hours HPL 575 115X 575 115 12 360 3 050 K 2000 hours HPL 375 115 375 115 10 540 3 250 K 300 hours HPL 375 115X 375 115 8 000 3 050 K 1000 hours HPL 575 120 575 120 16 520 3 250 K 300 hours HPL 575 120X 575 120 12 360 3 050 K 2000 hours HPL 575 230 575 230 14 900 3 200 K 400 hours HPL 575 230X 575 230 11 780 3 050 K 1500 hours HPL 375 230X 375 230 7 250 3 000 K 1000 hours HPL 575 240 575 240 14 900 3 050 K 400 hours HPL 575 240X 575 240 11 780 3 050 K 1500 hours HPL 375 240x 375 240 7 250 3 000 K 1000 hours To be used with ETC Dimmer Doubler Color frame holder Retaining clip
3. 9 Sheung Yuet Road Kowloon Bay Kowloon Hong Kong m Tel 852 2799 1220 Fax 852 2799 9325 Service Americas service etcconnect com m UK service etceurope com m DE techserv hoki etcconnect com w Asia service etcasia com Web www etcconnect com m Copyright O 2008 ETC All Rights Reserved m Product information and specifications subject to change 7062M1200 06 01 m Rev C m Released 2010 01
4. Four jr jr Zoom User Manual Adjustments Centering lamp and adjusting the field Flat field best adjustment Rear lamp Inner Knob housing peak flat field adjustment Hot spot lamp pulled out too far Field with hole lamp Outer Knob lamp pushed in too far center adjustment Figure 4 Figure 5 The two concentric knobs located on the lamp housing allow you to align the lamp and adjust its field See Figure 4 The outer knob centers the lamp within the reflector The inner knob adjusts the lamp s field Step 1 Turn on the fixture and aim it at a flat surface Adjust the barrel to create a hard edge Step 2 Unlock and loosen the outer knob by turning it counterclockwise Step 3 Gently move the outer knob from side to side and up and down until the lamp is centered within the reflector Step 4 Once the lamp is centered turn the outer knob clockwise to lock it in place Step 5 Finally turn the inner knob either clockwise or counterclockwise to achieve an optimum flat field See Figure 5 Focusing the beam y Beam focus knobs Figure 6 On a fixed field angle Source Four jr with a 267 36 or 50 lens adjust the lens single beam focus knob to focus the edge of the beam On a Source Four jr Zoom adjust the position of both lens beam focus knobs to set the beam s spread and to focus the edge of the beam The Zoom lens provide a range from 25 to 50 Step 1 Loosen the beam focus knob s on the underside of the barre
5. SOURCE FOU Puer Zoom User Manual Production Dates September 2004 Present Copyright O 2008 Electronic Theatre Controls Inc All Rights reserved Product information and specifications subject to change Part Number 7062M1200 06 01 Rev C Released January 2010 Picking 7062M1001 C Table of Contents Basic Assembly ccs 0 1 Fixture information llle eese 2 Color frame holder 2 Replacing the HPL lamp LL 4 US 5 Centering lamp and adjusting the field 5 Focusing the beam 0 0 5 Shaping the beam 000 6 Adjusting the C clamp 0 000 7 Adjusting the yoke position 00 eee 7 Lens and Reflector ss ii eel um eee 9 Switching lens assemblies llis iles 9 Cleaning glass lens 00 10 Cleaning the reflector 0 10 ETC Emphasis Expression Insight Imagine Focus Express Unison Obsession Il ETCNet2 EDMX Source Four Revolution Sensor and WYSILink are either registered trademarks or trademarks of Electronic Theatre Controls Inc in the United States and other countries All other trademarks both marked and not marked are the property of their respective owners Basic Assembly C clamp mounting Yoke Pattern holder slot 0 A Lamp housing Drop in iris ZX 4 slot cover Color frame e retaining gel clip arre Gel frame Zoom rear focus knob Beam focus knob
6. ffle and secure it with the retaining screw Note Reverse steps 1 6 to replace Zoom lens with a standard lens Cleaning glass lens WARNING Do not use ammonia based or other harsh commercial cleaners Clean lens only as directed Commercially available glass cleaning agents should be avoided as they may contain ammonia other harsh chemical detergents or abrasive agents These cleaners may damage the glass surface and the Anti Reflective coatings Do not immerse or soak the glass in any cleaning solution Replace lenses if they contain visible damage cracks or deep scratches that may impair their effectiveness Step 1 Remove the lens assembly See Source Four jr jr Zoom Assembly Guide for lens removal instructions Step 2 Remove dust with a blast of oil free air or wipe with a clean lint free cloth Isopropyl alcohol distilled water or a 5096 5096 mixture of each can be used to clean the glass surface Step 3 Reinstall the lens assembly Cleaning the reflector WARNING Unplug the fixture before attempting to clean the reflector WARNING Do not use ammonia based or other harsh commercial cleaners Clean reflector only as directed Commercially available glass cleaning agents should be avoided as they may contain ammonia other harsh chemical detergents or abrasive agents These cleaners may damage the glass surface and the Anti Reflective coatings Do not immerse or soak the glass in any cleaning sol
7. in which the fixture is mounted see Figure 10 To change the height position perform the following steps General use position l Low clearance position Lo Um 76 Yoke locking knob Figure 10 Step 1 Remove the yoke locking knobs washers and hex bolts from either side of the fixture Step 2 Raise or lower the fixture to the desired position within the yoke Step 3 Reinstall the yoke s hex bolts washers and locking knobs Step 4 Tighten the yoke knobs to secure in position Setting the angle within the yoke Yoke locking knob Figure 11 Step 1 Loosen the yoke locking knobs see Figure 11 Do not remove them Step 2 Tilt the fixture to the desired position Step 3 Tighten the yoke locking knobs to secure in position Source Four jr jr Zoom User Manual Lens and Reflector Switching lens assemblies Follow these procedures to replace a fixed field lens with Zoom lens Lens tray Light baffle and retaining screw Figure 12 Step 1 Loosen the screw at the front of the baffle See Figure 12 Step 2 Pull the light baffle out of the barrel Step 3 Remove the beam focus knob from the bottom of the barrel and slide the lens assembly from the barrel Step 4 Slide the Zoom lens rear assembly into the barrel and install its beam focus knob Step 5 Slide the Zoom lens front assembly into the barrel and install its beam focus knob Step 6 Reinstall the light ba
8. l as shown in Figure 6 Step 2 Slide the lens es forward or backward to achieve the desired beam edge Step 3 Once the fixture is focused tighten the beam focus knob s Shaping the beam The beam can be shaped using the shutters see Figure 1 a pattern or an optional drop in iris Pattern Projection The pattern holder slot is on the top side of the barrel and in front of the shutters It accommodates an M size pattern holder see Figure 7 The pattern holder handle can be bent away from the shutter handle to keep it from interfering with the action of the shutter handle Use an optional donut in the accessory holder to enhance pattern projection Donut diameter range should be 2 5 to 2 75 M Size Pattern holder Q Figure 7 Drop In Iris Slot Pattern holder slot Drop in iris slot Iris E O gt IMs Figure 8 The drop in iris slot is located on the top of the barrel and in front of the pattern holder slot It accommodates either a drop in iris or a motorized pattern device When the slot is not in use a small sheet metal cover secured with two Phillips screws prevents light leakage see Figure 8 Step 1 Use a Phillips screwdriver to loosen the screws on the drop in iris slot cover Do not remove screws Step 2 Slide the cover completely forward to expose the slot Step 3 Insert the iris with the flat side toward the shutters and make sure the iris handle exte
9. nds from the slot Step 4 Slide the slot cover back toward the shutters until it meets the iris handle Leave enough space to move the iris handle Step 5 Secure the drop in iris slot cover by tightening the screws Source Four jr jr Zoom User Manual Adjusting the C clamp Pipe bolt i p C clamp A OF Yoke bolt and lockwasher Pan screw _ Yoke o O NP Figure 9 The C clamp attaches the fixture to the mounting pipe and allows you to adjust the position of the fixture once it is mounted see Figure 9 Step 1 Tightly fasten the C clamp to the yoke with the provided yoke bolt and lock washer Step 2 Place the C clamp on mounting pipe then tighten the pipe bolt to secure it Step 3 Loosen the C clamp pan screw and rotate the yoke to the desired position Step 4 Tighten the pan screw to lock the fixture CAUTION Tighten C clamp pipe bolt to 15 20 ft Ibs approximately finger tight plus up to one quarter turn Do not exceed 25 ft Ibs Do not use excessive force Tighten the yoke pivot bolt to 5 10 ft lbs approximately finger tight plus up to one eighth turn Do not exceed 15 ft lbs Do not use excessive force Adjusting the yoke position The Source Four jr jr Zoom provide multi positioning capabilities within its yoke for overall fixture height and angle Setting the fixture height within the yoke The fixture is equipped with a two position yoke for modifying the overall height
10. ution To quickly clean the reflector and You may also wipe the reflector with a clean lint free cloth If either method is not sufficient follow these steps Step 1 Step 2 Step 3 Step 4 Step 5 To protect the lamp housing during cleaning remove the lamp housing by loosening the knurled bolt and pulling the housing straight out See Figure 3 Remove the lens See Source Four jr jr Zoom Assembly Guide for full fixture disassembly assembly instructions Remove dust with a blast of oil free air or wipe with a clean lint free cloth Isopropyl alcohol distilled water or a 5096 5096 mixture of each can be used to clean the glass surface Reinstall the lamp housing and tighten the knurled bolt Reinstall the lens Source Four jr jr Zoom User Manual 11 12 Source Four jr jr Zoom User Manual 13 14 Source Four jr jr Zoom User Manual ODE Corporate Headquarters 3031 Pleasant View Road P O Box 620979 Middleton Wisconsin 53562 0979 USA m Tel 608 831 4116 Fax 608 836 1736 London UK m Unit 26 28 Victoria Industrial Estate Victoria Road London W3 6UU UK m Tel 44 0 20 8896 1000 m Fax 44 0 20 8896 2000 Rome IT a Via Ennio Quirino Visconti 11 00193 Rome Italy Tel 39 06 32 111 683 m Fax 39 06 32 656 990 Holzkirchen DE Ohmstrasse 3 83607 Holzkirchen Germany m Tel 49 80 24 47 00 0 m Fax 149 80 24 47 00 3 00 Hong Kong Rm 1801 18 F Tower 1 Phase 1 Enterprise Square
11. vailable See HPL lamp table page 2 Operating HPL lamps above their rated voltage reduces lamp life and can cause premature lamp failure WARNING Let the lamp cool before replacing Step 1 Disconnect power to the fixture before installing the lamp Step 2 Loosen the knurled bolt on the back of the lamp housing and pull the housing out Step 3 Holding by the base remove the HPL lamp from its box CAUTION Use caution when installing or replacing any lamp When installing replacing lamp be sure to point the lamp away from your face and away from others before inserting it firmly into the assembly This may prevent injuries if the lamp should break INCORRECT Ch gt CORRECT IN Note To avoid premature lamp failure do not touch the lamp glass If you do clean it carefully with isopropyl alcohol and a clean lint free cloth Allow to dry before operation Step 4 Align the flat sides of the lamp base with the retention brackets on either side of the Socket as shown in Figure 3 Step 5 Push down on the lamp base until the lamp seats firmly When properly installed the top of the lamp s base will be even with he top edges of the retention brackets A CAUTION Improperly installed lamps cause premature lamp failure and socket problems Step 6 Press lamp retaining clip across lamp base to secure Step 7 Reinstall the lamp housing by aligning the bolt hole and tightening the knurled bolt 4 Source
Download Pdf Manuals
Related Search