Home

IM-T8319 - New Japan Radio

1. Page 6 2 Safety Instructions Use the following safety guidelines to help protect the Unit from potential damage and to help ensure your own personal safety DANGER WARNING CAUTION and NOTE Statements DANGER WARNING CAUTION and NOTE statements are used throughout this instruction manual to emphasize important and critical information You must read these statements to help ensure safety and to prevent product damage The statement are defined below Statement Symbol DANGER Fada ia DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION CAUTION indicates a potentially hazardous situation which if not avoided could result in minor or moderate injury CAUTION may also be used to indicate other unsafe practices or risks of property damage NOTE NOTE NOTE is used to notify of installation operation or maintenance information that is important but not hazard related NJT8319 series Instruction Manual Page 7 New Japan Radio Co Ltd IM T8319 Rev 01 Symbol GENERIC HAZARD ELECTRIC HAZARD A HOT SURFACE A MOVING PARTS When installing the Unit observe the following safety guidelines 2 1 Safety Statements 1 Opening Removing ua DO NOT dismantle this product Dismantlement may cause malfunction a
2. 5 Data Byte 3 bit in 1 dB digit 6 Data Byte 4 t Att bit in 0 5 dB digit 7 checksum Algebraic sum of bytes 1 6 L f Request Status 2 i Address address of BUC 3 Data Byte 1 Attenuator Selection lor 2 Att 1 0x01 Att 2 0x02 pata Byte 2 5 Data Byte 3 Set Att bit in 1 dB digit 6 Data Byte 4 Set Att bit in 0 5 dB digit C Jenecksum Jalgebraic sunofbytesi 6 SSS RS232C M amp C_rev2 3 New Japan Radio Co Ltd 4 4
3. Connecting the the RS 232C Interface is proceeded with the following Step 1 Assemble the cable and the supplied MS mating connector with the following assignment Pin G RS 232C TxD Pin H RS 232C RxD Pin K GND COMMON RS 232C Step 2 Connect the MS connector and the COM port of user s PC with the above cable 7 1 2 COM Port Setting Set the serial communication property of your PC as follows Baud rate 9600 Data bit 8 Parity none Stop bit 1 Flow control none 7 1 3 Installing the GUI Software The GUI Software can be installed by Setup exe in the downloaded zip file The details of Installing the GUI software are mentioned in the user manual which is stored in Manual htm in the downloaded zip file 7 2 Starting and Operating The details of starting and operating the GUI software are mentioned in the user manual which is stored in Manual htm in decompressed folder NJT8319 series Instruction Manual Page 22 New Japan Radio Co Ltd IM T8319 Rev 01 8 Maintenance This Section describes basic maintenance for the Unit 8 1 Fan Field Replacement The Unit is Forced Air by fan for cooling The fan has its lifetime The fan is to be replaced with a new one at appropriate interval The recommendation interval of replacement is five years The fan of the Unit stop and does not operate normally you need to replace a new fan by yourself in field And the fan is to be replaced with a new one at five years interval Cont
4. 68 to 1 13 NN m F type connector 0 39 to 0 49 N m 3 Weatherproof The Unit is mounted outdoors must be adequately weatherproofed Ensure the waveguide joints are properly sealed with the supplied o ring gasket Use self amalgamating tape to seal connectors and cable entry points from the connector to the The fan has its lifetime The fan is to be replaced with a new one at appropriate interval The recommendation interval of replacement is five years 5 Warranty Opening or removing any component e g label and screws without fan equipments or sealed area will immediately void the warranty NJT8319 series Instruction Manual Page 10 New Japan Radio Co Ltd IM T8319 Rev 01 3 Packing List The Unit is shipped in a single shipping container with the following content No Qty Description __________ 1 1 unit NJT8319N NJT8319F NJT8319NM NJT8319FM NJT8319NK NJT8319FK NJT8319NMK NJT8319FMK NJT8319NMR NJT8319FMR NJT8319UN NJT8319UF NJT8319UNM NJT8319UFM NJT8319UNK NJT8319UFK NJT8319UNMK NJT8319UFMK NJT8319UNMR OR NJT8319UFMR 2 1 set Accessory Qty 4 Hexagon Socket Head Bolt M4x10 Qty 1 Hexagon Wrench Key M4 Qty 2 Phillips head Screw M6x10 Qty 1 O ring 4 ipc Mating MS Connector Part Number PTO6E 14 12S 470 MS connector is enclosed in the shipping container the only MS Connector models NJT8319 series Instruction Manual Page 11 New Japan Radio Co Lt
5. H d Maximum Response Time e Massage Rate 20 ms 2 Packet Format 1 Byte Configuration a Data Packet Length b Byte Configuration mand IDU to BUC Response BUC to IDU 1 Initial setting of a BUC address is 0x01 2 Responder address is shifted left by 4 bits 3 Algebraic sum of bytes 1 through 6 Spare bytes are always filled with OxAA 10101010 FSK M amp C_rev3 0 New J apan Radio Co Ltd 1 4 Appendix 3 Command amp Response Message Structure The last state of the BUC condition is stored to inside memory so when the BUC is re turned DC power on again the state is reproduced last condition 1 Command Message Structure IDU to BUC a Request Status 1 2 3 6 bata Byte4 Not used fa 222 7 _ checksun Algebraic sumofbytesi 6 SS b Set Transmit On Off State 2 3 La Pata Byte 2 Not used 6 Dat OxAA 0 7 _ enecksum algebraic sum of bytes 1 6 TS C Change BUC Address N A 2 Ce pata Byte 4 not sed aa 7 checksum Algebraic sun of bytes 1 8 AA This command is not applicabe N A in this version Value A d Set Carrier Frequency N A 2 3 5 bata Byte 3 not used OKRA Le pata Byte 4 not used DAA 7 recken Algebraic sum of bytes 18 IA This command is not applicabe N A in this version Data Field Definition Carrier Frequency Unsigned integer in MHz ex 14000 MHz 36 BO Convert into a hexadecimal number LL Da
6. IF Interface Connector M MS Connector IF Interface Connector N N type 50 ohms Female Connector F F type 75 ohms Female Connector RF Frequency Non Suffix Standard Ku band 14 0 to 14 5 GHz U Universal Ku band 13 75 to 14 5 GHz Output Power 1dB G C P 18 39 0 dBm 8W 19 42 0 dBm 16W Product Series Number NJT8319 series Instruction Manual Model No RF Local IF Output Power IF Port for Power M amp C Frequency Frequency Frequency PidB Connector Voltage Input Supply Option NJT8319N N type Same as NJT8319F F type IF Connector NJT8319NM N type MS Connector NA NJT8319FM F type Separate Port NJT8319NK 14 0 to 14 5GHz 13 05 GHz 950 to N type Same as FSK NJT8319FK Standard Ku band j 1 450 MHz F type IF Connector Ae A AA Communication NJT8319NMK N type MEC NJT8319FMK F type MS Connector NJT8319NMR N type Separate Port RS 232C NJT8319FMR 16W Linear F type 36 to 60 V Interface M amp C NJT8319UN 42dBm min N type Same as DC Power NJT8319UF F type IF Connector N A NJT8319UNM N type MS Connector NJT8319UFM F type Separate Port NJT8319UNK 13 75 to 14 5GHz incik 950 to N type Same as Fek NJT8319UFK Universal Ku band 1 700 MHz F type IF Connector SV a Set Communication NJT8319UNMK N type mac NJT8319UFMK F type MS Connector NJT8319UNMR N type Separate Port RS 232C NJT8319UFMR F type Interface M amp C
7. New Japan Radio Co Ltd IM T8319 Rev 01 Instruction Manual for Ku band 16W BUC NJT8319 series Document Part Number IM T8319 Revision 01 Issue Date April 30 2014 Copyright 2014 New Japan Radio Co Ltd All rights reserved This instruction manual may not be reproduced in part or in whole without the permission of New Japan Radio Co Ltd The specifications and information regarding the products in this instruction manual are subject to change without notice All statements information and recommendations in this instruction manual are believed to be accurate but are presented without warranty of any kind express or implied Users must take full responsibility for their application of any products NJT8319 series Instruction Manual Page 1 New Japan Radio Co Ltd IM T8319 Rev 01 General Caution NJRC strives to produce reliable and high quality microwave components NJRC s microwave components are intended for specific applications and require proper maintenance and handling To enhance the performance and service of NJRC s microwave components the devices machinery or equipment into which they are integrated should undergo preventative maintenance and inspection at regularly scheduled intervals Failure to properly maintain equipment and machinery incorporating these products can result in catastrophic system failures 2 To ensure the highest levels of reliability NJRC products must always be proper
8. When BUC Temperature is 40C Temperature data is 3 BUC Power Class Oxs oxa Oxs oxe 0x7 O O Oxa 0x1036 gt 41 50 dBm FSK M amp C_rev3 0 New J apan Radio Co Ltd 3 4 Appendix b Set Transmit 2 3 6 pata Byte 4 mot used fea 2 r checksum Algebraic sum of pytes 176 cC Change BUC Address N A 7 _ checksum Algebraic sum of bytes ie OOOO This command is not applicabe N A in this version d Set Carrier Frequency N A 3 7 Dat Dat pata Byte 4 Not_used O OO o ooa y O 7 Checksum algebraic sum oF bytes 1 6 This command is not applicabe N A in this version e Set Attenuator 1 Address Address of BUC shifted left by 4 0x10 to 0xF0 2 commana 3 Data Byte 1 Attenuator Selection lor 2 Att 1 0x01 Att 2 0x02 Data Byte 2 Set Att bit in 10 dB digit Data Byte 3 Data Byte 4 Set Att bit in 0 5 dB digit 7 Checksum Algebraic sum of bytes 1 6 f Request Status 2 Pi Address 3 Data Byte 1 Attenuator Selection lor 2 Att 1 0x01 Att 2 0x02 Data Byte 2 Data Byte 3 Set Att bit in 1 dB digit Data Byte 4 Set Att bit in 0 5 dB digit 7 Checksum algebraic sum of bytes 16 FSK M amp C_rev3 New Japan Radio Co Ltd 4 4 Appendix Monitor Control Specifications for RS 232C Interface Rev 223 July 25 2013 1 RS 232C Link Specificatons 1 Transmission Protocol a Operation Mode Binary b Transfer Rate 9600 bit s c Data Format 1 s
9. a Byte 2 7 Checksum Algebraic sum of bytes 1 8 are This command is not applicabe N A in this version Data Field Definition Carrier Frequency Unsigned integer in MHz ex 14000 MHz 36 BO Convert into a hexadecimal number UL Data byte 1 is 0x36 RS232C M amp C_rev2 3 New Japan Radio Co Ltd 2 4 e Set Attenuator E E VETE IE t Attenuator Data Byte 1 ttenuator Selection 1 or 2 Att 1 0x01 Att 2 0x02 1 4 Da ata Byte 2 etting At in 10dB digit 0x00 or 0x01 2 Ps ata Byte 3 a Att in 1dB digit 0x00 to 0x09 K2 ata Byte 4 Setting Att bit in 0 5dB digit 0x00 or 0x05 EZ Checksum Algebraic sum of bytes 1 8 AAA 1 Att 1 is available Att 2 is not avalable 2 Dynamic range and step size of the step attenuator 15 5dB in 0 5dB step ex 12 5dB Data byte 2 is 0x01 Data byte 3 is 0x02 Data byte 4 is 0x05 f Request Status 2 Pi Address address of BO po OOP 2 omani request status 2 os 7 Data Byte 1 ttenuator Selection 1 or 2 Att 1 0x01 Att 2 0x02 AA pata Byte 2 5 Ipata Byte 3 a e is a 2 Response Message Structure BUC to IDU a Request Status 1 2 Jrevel Byte 1 usbyte of Tx Output Power Ja 3 level Byte 2 ae of Tx Output Power a o A 5 Status Byte 1 Bit 0 Temperature Out of Range Fail 0 Normal Bit 1 PLL Out of Lock Fail 0 Normal it 2 Checksum Error t 3 Tx Status liTx On Tr Off its 4 thru 7 BUC Power Class 0x1 to OxA 3 St
10. act to us by phone fax or email when a new fan for replacement is needed Telephone 81 49 278 1270 Fax 81 49 278 1234 Email mcsales njr co jp NJT8319 series Instruction Manual Page 23 New Japan Radio Co Ltd IM T8319 Rev 01 9 Specifications The Unit is in compliance with the following specifications 9 1 Electrical Specifications No TStem Specifications Output Frequency Range lt Universal Ku band gt 13 75 to 14 5 GHz lt Standard Ku band gt 14 0 to 14 5 GHz Input Frequency Range lt Universal Ku band gt 950 to 1 700 MHz lt Standard Ku band gt 950 to 1 450 MHz without damage 4 Conversion Type Single fixed LO 6 L O Frequency lt Universal Ku band gt 12 80 GHz lt Standard Ku band gt 13 05 GHz 6 FrequencySense____ Positive ___________ 8 LinearGain_____ 68 dB nom 62 dB min total power lt 42 dBm 3 dB Requirement for External Reference Frequency 10 MHz sine wave Input Power 5 to 5 dBm Input port Phase Noise 125 dBc Hz max 100 Hz 135 dBc Hz max 1 kHz 140 dBc Hz max 10 kHz L O Phase Noise 60 dBc Hz max 100 Hz 70 dBc Hz max 1 kHz 80 dBc Hz max 10 kHz 90 dBc Hz max 100 kHz 100 dBc Hz max 1MHz Input Impedance lt N type Model gt 50 ohms nom lt F type Model gt 75 ohms nom Input VSWR Output VSWR 15 Output Load VSWR for Non 2 1 max Damage NJT8319 series Instruction Manual Page 24 New Japan Radio C
11. atus Byte 2 Bits 0 3 Not used Fixed OxA its 4 7 Software Version 0x0 to OxF ma Giese PISTA Ld 1 Data Field Definition Output power is the number which changed hexadecimal data into the decimal number and was divided by 100 ex Output Power Data Output Power Data byte 1 is 0x10 Data byte 2 is 0x36 2 Data Field Definition Temperature data is 128 deg C to 127 deg C in two s complement 1 deg C step ex 0x1036 gt 41 50 dBm When BUC Temperature is 40C Temperature data is 3 BUC Power Class RS232C M amp C_rev2 3 New Japan Radio Co Ltd 3 4 b Set Transmit PI fddress Address of BUC shifted left by 4 0x10 to OsFO 3 bata Byte 1 6 Data Byte nor used fea O 7 checksum Algebraic sumofbytesz 6 JOO SCS c Change BUC Address N A Pi Address address of BUC shifted left by 4 0x10 to 0 F0 3 Data Byte1 New Address 0x01 to 0x0F a pata Byte 2 not sed oa Ss pata Byte 3 Notus OO O fo Ca Byte 4 Checksum aigebraic sun of bytes 1 6 EG This command is not applicabe N A in this version d Set Carrier Frequency N A 2 command 3 pata nyte Pa bata Byte 2 e pata Byte 4 7 checksum Algebraic sum of bytes 1 6 a A This command is not applicabe N A in this version e Set Attenuator 1 Address Address of BUC shifted left by 4 2 comana 3 Data Byte 1 Attenuator Selection lor 2 Att 1 0x01 Att 2 0x02 0 4 Data Byte 2 bit in 10 dB digit
12. ctors it may damage the unit or the unit may not operate properly NJT8319 series Instruction Manual Page 27 9 3 Environmental Specification D Temperature Range ambient Operating Operation Guarantee 40 to 75 C Performance Guarantee 40 to 55 C Storage 40 to 75 C Altitude 15 000 feet 4 572 m Vibration 5 G 49 03 m s 3 axis 50 Hz to 2 kHz 1 mm p p 3 axis 5 to 50 Hz P seam erases Regulatory Compliance CE EMC Directive 2004 108 EC Comply with RoHS Restricting the use of Hazardous Substances directives NJT8319 series Instruction Manual Page 28 Appendix Monitor Control Specifications for FSK Communications Interface Rev 3 0 June 14 2013 1 FSK Communications Specifications 1 Transmitter Frequency 650 kHz 5 FSK deviation 60 kHz Nominal 60 kHz mark Deviation tolerance 50 kHz minimum 70 kHz maximum Output Level 5 to 15 dBm Output impedance 50 Ohm Start Tone 710 kHz Start Tone Time 10 ms minimum 2 Receiver a Locking range 32 5 kHz b Input impedance 50 Ohm c Input Sensitivity 15 dBm 3 Transmission Protocol a Operation Mode Legacy Binary b Transfer Rate 9600 bit s C Data Format 1 start bit 8 data bits 1 stop bit No Parity st D0 p1 p2 D3 p4 p5 D6 D7 sP mdm i Transmit The least significant bit LSB is sent first ST Start bit Status L DO Data LSB D7 Data MSB SP Stop bit Status
13. d 4 Overview IM T8319 Rev 01 The Unit transmits an RF signal Universal Ku band 13 75 to 14 5 GHz Standard Ku band 14 0 to 14 5 GHz output with up to 16W 42 dBm linear The unique features are High Temperature Operating Operation Guarantee Temperature Range 40 to 75 degree C RF Frequency Line up Universal Ku band 13 75 to 14 5 GHz Standard Ku band 14 0 to 14 5 GHz High Efficiency amp Low Distortion P1dB 42 dBm min over temperature IM3 28 dBc Pout 39 dBm Power Consumption 160 W typ Monitor amp Control Line up FSK Communication M amp C RS 232C Interface Serial M amp C Smaller Size amp Lighter Weight Dimension 180 L x 130 W x 80 H mm Weight 2 4 kg LED Indicator ROHS Compliance Monitor and Control DC Power DC Input Supply DC 36 to 60 V RS 232C Signal l pc _ imac AMP Waveguide WR75 ee AMP HPA Coaxial Connector Multi IF plexer IF Input 950 to 1 450 MHz REF 950 to 1 700 MHz Reference REF 10 MHz DC Input PLO 36 to 60 V I amp C FSK Communication Signal PS 12 80 GHz 13 05 GHz Block Diagram NJT8319 series Instruction Manual RF Output 14 0 to 14 5 GHz 13 75 to 14 5 GHz Page 12 dk ea IM T8319 Rev 01 5 Physical Description This section describes appearance and outlin
14. e for the Unit 5 1 Appearance Overall Picture NJT8319 series Instruction Manual Page 13 New Japan Radio Co Ltd IM T8319 Rev 01 5 2 Outline Drawing Grounded hole M6 depth 10 MIN 45 36 7 5 y lt 36 7 N Female Connector eee depth 6 IN S 38 22 15 FSK M amp C Signal 9 180 1 _ 2 a 28 540 05 IF REF DC Power input te Sane TA oo Go F oy M6 e a ME depth 10 MIN E 6 F a 7 al a i D QR code Label o 1 hi y geo m for JRC al a v 2 E e J 33 7 Sj pfa enh RE See ST deptht 9528 88 Os LED Indicator o a E i y ai ar AN hf o depth 6 MIN foie Y fue y g He n gt CIRCULAR CONNECTOR AAA AQ PTO2E 14 12P 0 R2320 M amp C Signal gt 36 7 Grounded hole ower input re Feen a i 80 1 M6 depth 10 MIN e a Fl Nameplates Label _ UNIT mm Tolerance 0 5 NJT8319 series Instruction Manual Page 14 New Japan Radio Co Ltd IM T8319 Rev 01 5 3 Description of Connectors and LEDs N type or F type Female Connector Circular Connector MS Connector IF Signal Input The Unit receives an IF signal 950 to 1 450 MHz or 950 to 1 700 MHz via thi
15. larm Intruder Detector Vehicle Control Equipment automobile airplane railroad ship etc Various Safety Equipment NJT8319 series Instruction Manual Page 2 New Japan Radio Co Ltd IM T8319 Rev 01 General Caution continued 6 NJRC s products have been designed and tested to function within controlled environmental conditions Do not use products under conditions that deviate from methods or applications specified in the catalog and specification sheets Failure to employ NJRC s products in the proper applications can lead to deterioration destruction or failure of the products NJRC shall not be responsible for any bodily injury fires or accidents property damage or any consequential damages resulting from the misuse or misapplication of its products PRODUCTS ARE SOLD WITHOUT WARRANTY OF ANY OF KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE NJT8319 series Instruction Manual Page 3 New Japan Radio Co Ltd IM T8319 Rev 01 About This Instruction Manual This instruction manual describes Ku band 16W BUCs Model No NJT8319 series herein referred to as the Unit This instruction manual provides information and instructions for installation and operation of the Unit This instruction manual is intended for use by trained field installers or system engineers responsible for satellite networks Updated instruction manual ma
16. ly handled The introduction of external contaminants e g dust oil or cosmetics can result in failures of microwave components 3 NJRC offers a variety of microwave components intended for particular applications It is important that you select the proper component for your intended application You may contact NJRC s sales office or sales representatives if you are uncertain about the products listed in the catalog and the specification sheets 4 Special care is required in designing devices machinery or equipment which demand high levels of reliability This is particularly important when designing critical components or systems whose foreseeable failure can result in situations that could adversely affect health or safety In designing such critical devices equipment or machinery careful consideration should be given to amongst other things their safety design fail safe design back up and redundancy systems and diffusion design 5 The products listed in the catalog and specification sheets may not be appropriate for use in certain equipment where reliability is critical or where the products may be subjected to extreme conditions You should consult our sales office or sales representatives before using the products in any of the following types of equipment Aerospace Equipment Equipment Used in the Deep Sea Power Generator Control Equipment nuclear steam hydraulic Life Maintenance Medical Equipment Fire A
17. nd electric shock 2 Input Voltage VW ee Only input a voltage within the range indicated in specified voltage DO operate at the input voltage of 36 to 60 V DC power NJT8319 series Instruction Manual Page 8 New Japan Radio Co Ltd IM T8319 Rev 01 RF Radiation A radiation hazard exists if the BUC is operated with its RF signal output unterminated DO NOT operate the BUC without a load or termination attached to the RF signal output High Temperatures DO NOT touch the body especially fins during operating the Unit High touch temperatures may exist depending on load conditions DO NOT insert your finger into the fan to avoid injury DO NOT insert any objects into the fan Keep any objects away from the fan Incorrect usage may cause injury to self or others a Z Input Level DO NOT input an IF signal over the range of 13 dBm maximum and a reference signal within the range of 5 to 5 dBm Operating Temperature Operate the Unit within the ambient temperature range of 40 to 75 degree C but the performance guarantee temperature range is 40 to 55 degree C NJT8319 series Instruction Manual Page 9 New Japan Radio Co Ltd IM T8319 Rev 01 2 2 Instruction Statements 1 Mounting DO NOT block the fins and air flow Normally the Unit should be mounted with fan face down 2 Connector When attaching cable DO tighten as connector with following torque N type connector 0
18. o Ltd IM T8319 Rev 01 A Specifications DC Power Requirement Voltage Range 48 VDC 36 to 60 VDC Power Consumption 140 W typ No IF signal 160W typ 180 W max Pout 42 dBm 17 Mute Shut off the HPA in case of L O unlocked 18 LED Indicator GREEN L O locked RED L O unlocked or no 10 MHz reference signal 19 Monitor and Control____ __________________ lt FSK Communication M amp C gt Interface 650kHz FSK Signal on IF Connector Functions Monitor Tx Output Power Temperature Tx Status Alarm Over temperature 2 L O unlock Step Attenuator Control Transmit On Off Step Attenuator Performance Tx Output Power Detector Range 15 dB up to P1dB Reading Accuracy 1 0 dB Step Attenuator Attenuator Range 0 to 15 5 dB Attenuator Step 0 5 dB Details are mentioned on Appendix of Monitor amp Control Specifications for FSK Communications Interface NJT8319 series Instruction Manual Page 25 No TSttem Specifications 19 Monitor and Control J __________________ lt RS 232C Interface M amp C gt Interface RS 232C Interface on MS connector Functions Monitor Tx Output Power Temperature Tx Status Alarm Over temperature 2 L O unlock Step Attenuator Control Transmit On Off Step Attenuator Performance Tx Output Power Detector Range 15 dB up to P1dB Reading Accuracy 1 0 dB Step Attenuator Attenuator Range 0 to 15 5 dB Attenuato
19. onnecting the power cable is proceeded with the following steps Step 1 Step 2 Step 3 Assemble the power cable and the supplied MS mating connector with the following assignment Pin J Prime 48 V DC Power Pin K Prime Return Do not connect the pins for N C and not using pins with the cable wires Connect the power cable above to MS connector equipped with a bayonet locked status Use self amalgamating tape to seal connector and cable entry points from the connector to the cable sheath Only input a voltage within the range indicated in specified voltage DO operate at the input voltage of 36 to 60 V DC power at the coaxial connector on the Unit DO NOT apply DC voltage via both MS Connector and N F type Female Connector If DC voltage is applied on both connectors it may damage the unit or the unit may not operate properly y 0 Connecting the power cable NJT8319 series Instruction Manual Page 19 New Japan Radio Co Ltd IM T8319 Rev 01 6 2 3 Wire for Common Chassis Ground Earthing The Unit can be had the chassis ground of the other equipment e g antenna in common or earthing Connecting the wire for common chassis ground earthing is proceeded with the following steps Step 1 Connect the grounding earthing wire from ground on the other equipment or earthing point to the ground hole on connector or waveguide sides with M6 screw A E ALI Connect the grounding ea
20. r Step 0 5 dB Details are mentioned on Appendix of Monitor 8 Control Specifications for RS 232C Interface 2 Regardless of cooling fan status the unit will operate until status of over temperature which turn out at internal temperature of around 120 C and the Mute and Alarm will function at status of over temperature NJT8319 series Instruction Manual Page 26 9 2 Mechanical Specifications A A O Input Interface IF Connector N type or F type female connector IF Ref FSK M amp C Signal DC Input DC Input 3 IF Connector or MS Connector MS connector Part No PTO2E 14 12P 025 Mating connector PTO6E 14 12S 470 Assignment Pin A N C Pin B N C Pin C N C Pin D N C Pin E N C Pin F N C Pin G RS 232C TxD Pin H RS 232C RxD Pin J DC Power Prime Pin K DC Power Return GND COMMON RS 232C Pin L N C Pin M N C Pin G RS 232C TxD and Pin H RS 232C RxD are available for only RS 232C Interface M amp C models a not ar a F E N and A a with Grooved Flange 3 Cooling Forcedaircoded Dimension amp Housing without Interface Connector L 180 mm 7 09 W 130 mm 5 12 H 80 mm 3 15 2 4 kg 5 3 Ibs 3 MS Connector models are available to apply DC voltage via MS Connector or N F type Female Connector DO NOT apply DC voltage via both MS Connector and N F type Female Connector If DC voltage is applied on both conne
21. rthing wire OR Connect the grounding earthing wire NJT8319 series Instruction Manual Page 20 New Japan Radio Co Ltd IM T8319 Rev 01 6 2 4 Connecting M amp C Signal Cable The Unit is required to supply RS 232C interface signal via signal cable from modem or M amp C equipment in case that it is RS 232C interface M amp C models Connecting the M amp C signal cable is proceeded with the following steps Step 1 Assemble the M amp C signal cable and the supplied MS mating connector with the following assignment Pin G RS 232C TxD Pin H RS 232C RxD Pin K GND COMMON RS 232C Do not connect the pins for N C and not using pins with the cable wires Step 2 Connect the M amp C signal cable above to MS connector equipped with a bayonet locked status Step 3 Use self amalgamating tape to seal connector and cable entry points from the connector to the cable sheath Connecting the M amp C signal cable NJT8319 series Instruction Manual Page 21 7 GUI of Monitor and Control This Section describes the NJR s Graphical User Interface GUI of Monitor and Control The NJR s GUI is available for the RS 232C Interface M amp C models The GUI uses the BUC EP001 software which can be downloaded from the following NJR s website Website http mc njr co jp eng products vsat ku buc 8w_2 html Please download a zip file of the GUI software and decompress this 7 1 Setup 7 1 1 Connecting the RS 232C Interface
22. s connector Reference Signal The Unit receives a reference signal Input 10 MHz via this connector FSK FSK Communication M amp C models are Communication only equipped M amp C Signal The Unit receives transmits the M amp C signal with the FSK modulation via this connector DC Power Input 1 The Unit is required to supply 36 to 60 V DC power via this connector DC Power Input 1 MS Connector models are only The Unit is required to supply 36 to 60 V DC power via Pin J and K in this connector RS 232C Interface RS 232C Interface M amp C models are M amp C Signal only equipped The Unit receives transmits the M amp C signal with the RS 232C interface Pin G H and K in this connector Connector Information Part No PTO2E 14 12P 025 Mating connector PTO6E 14 12S 470 Assignment Pin A N C Pin B N C Pin C N C Pin D N C Pin E N C Pin F N C Pin G RS 232C TxD Pin H RS 232C RxD Pin J DC Power Prime Pin K DC Power Return GND COMMON RS 232C Pin L N C Pin M N C Pin G RS 232C TxD and Pin H RS 232C RxD are available for only RS 232C Interface M amp C models Do not connect the pins for N C and not using pins with the cable wires NJT8319 series Instruction Manual Page 15 WR 75 RF Output The Unit transmits an RF signal 14 0 to 14 5 GHz or 13 75 to 14 5 GHz via this waveguide LED Local Unlock Alarm GREEN L O locked Indicator RED L O
23. series Instruction Manual Page 17 New Japan Radio Co Ltd IM T8319 Rev 01 6 2 Connecting System The Unit is connected two cables Coaxial Cable Power Cable Wire for Common Chassis Ground Earthing M amp C Signal Cable 6 2 1 Connecting Coaxial Cable The Unit receives an IF signal and a reference signal via coaxial cable from modem is required to supply 36 to 60 V DC power receives an FSK communication M amp C signal Connecting the coaxial cable is proceeded with the following steps Step 1 Connect the coaxial cable with N type or F type male connectors to the coaxial connector equipped with the Unit under following torque N type connector 0 68 to 1 13 N m F type Connector 0 39 to 0 49 N m Step 2 Use self amalgamating tape to seal connector and cable entry points from the connector to the cable sheath Only input a voltage within the range indicated in specified voltage DO operate at the input voltage of 36 to 60 V DC power at the coaxial connector on the Unit DO NOT input an IF signal over the range of 13 dBm maximum and a reference signal within the range of 5 to 5 dBm e AU Connecting the coaxial cable NJT8319 series Instruction Manual Page 18 New Japan Radio Co Ltd IM T8319 Rev 01 6 2 2 Connecting Power Cable The Unit is required to supply 36 to 60 V DC power via power cable from modem or a DC power supply unit with the exception of only IF connecter supplied models C
24. ta byte 1 is 0x36 FSK M amp C_rev3 0 New J apan Radio Co Ltd 2 4 Appendix e Set Attenuator ata Byte 1 Attenuator Selection 1 or 2 Att 1 0x01 Att 2 0x02 z 5 6 Pata Byte 4 setting Att bit in 0 5aB digit 0x00 or 0x05 72 7 Jehscksun igebralo sum of bytes 126 O 1 Att 1 is available Att 2 is not avalable 2 Dynamic range and step size of the step attenuator 15 5dB in 0 5dB step ex 12 5dB Data byte 2 is 0x01 Data byte 3 is 0x02 Data byte 4 is 0x05 f Request Status 2 Commana ata Byte 1 Attenuator Selection 1 or 2 Att 1 0x01 Att 2 0x02 pi an bt e OXAR CONC CS a O Er Jenecksun Jpigebraie sun oF byes e O 2 Response Message Structure BUC to IDU a Request Status 1 i harese EA E revel Byte weyes of Te Output Pover a Level Byte uSbyte of Tx Output Power a O E A AAA 5 Status Byte 1 ae Temperature Out of Rang 1 Fail 0 Normal t 1 PLL Out of Lock 1 Fail 0 Normal Bit 2 Checksum Error Status Byte 2 Bits 0 3 Not used Ala its 4 7 Software Version 7 Checksum Algebraic sum of bytes 126 SSS 1 Data Field Definition Output power is the number which changed hexadecimal data into the decimal number and was divided by 100 ex Output Power Data Output Power Data byte 1 is 0x10 Data byte 2 is 0x36 2 Data Field Definition Temperature data is 128 deg C to 127 deg C in two s complement 1 deg C step ex
25. tart bit 8 data bits 1 stop bit No Parity spoje 9757 Transmit The least significant bit LSB is sent first ST Start bit DO Data LSB D7 Data MSB SP Stop bit 2 Packet Format 1 Byte Configuration a Data Packet Length b Byte Configuration Byte Pin BUC Address i BUC Address a Pres command Data Byte Td as Data Byte 1 DataByte2 Pan Data Byte 2 Data Bytes Tsim Data Byte 3 Data Byte 4 Gen Data Byte 4 Data Bytes Check Sum 3 itial setting of a BUC address is 0x01 2 Responder address is shifted left by 4 bits 3 Algebraic sum of bytes 1 through 6 Spare bytes are always filled with OxAA 10101010 RS232C M C_rev2 3 New Japan Radio Co Ltd 1 4 3 Command amp Response Message Structure The last state of the BUC condition is stored to inside memory so when the BUC is re turned DC power on again the state is reproduced last condition 1 Command Message Structure IDU to BUC a Request Status 1 6 Data Byte 4 notus aaa r Jenecksum Jatgebraic sum of bytes 18 b Set Transmit On Off o pata Byte 6 pata Byte 4 Notus fea 2 7 Checksum Algebraic sumofbytesi 6 SCS c Change BUC Address N A New Address Data Byte 3 nor used feas 7__ Checksum algebraic sun of bytes 1 4 ed This command is not applicabe N A in this version d Set Carrier Frequency N A command o Jpata Byte Ca pat
26. unlocked or no reference signal M6 hole Common chassis ground Hole 1 MS Connector models are available to apply DC voltage via Circular Connector MS Connector or N F type Female Connector DO NOT apply DC voltage via both Circular Connector MS Connector and N F type Female Connector If DC voltage is applied on both connectors it may damage the unit or the unit may not operate properly NJT8319 series Instruction Manual Page 16 New Japan Radio Co Ltd IM T8319 Rev 01 6 Installing This section describes basic installation for the Unit 6 1 Mounting Configuration The Unit can be mounted in the feed horn of the satellite antenna 6 1 1 Guidelines for Attachment of OMT When attaching the OMT or the filter you should follow the following steps Step 1 Verify that the o ring groove on the waveguide flange of the Unit is clean Insert the enclosed o ring gasket the groove as shown BUC Waveguide Ozring Flange Step 2 Secure the OMT or the filter to the Unit using the supplied enclosed bolts with 1 15 to 1 4 N m torque as shown when the thickness of the flange of the OMT or the filter is 3 5 to 5 0 mm When the thickness is not 3 5 to 5 0 mm you should prepare Bolt or Screw 6 1 2 Guidelines for Mounting When mounting on the OMT or the filter you should follow the following cautions DO NOT block the fins and air flow Normally the Unit should be mounted with fan face down NJT8319
27. y be available from NJRC s sales group mcsales njr co jp Contents Le INTO UCA re 5 6 2 Safety Instructions ia 7 10 3 Packing A 11 AT OT ao sae tec a dee 12 Ba Physical Description suicida 13 16 6 Installing corr ii lis 17 21 7 GUI of Monitor and Control asar 22 Se MainNt na NCE src 23 9 Specificaties Ea 24 28 NJT8319 series Instruction Manual Page 4 New Japan Radio Co Ltd IM T8319 Rev 01 1 Introduction This instruction manual is for Ku band 16W BUCs Model No NJT8319 series The Unit receives a reference signal 10 MHz and an IF signal L Band 950 to 1 450 MHz or 950 to 1 700 MHz input and transmits an RF signal Standard Ku band 14 0 to 14 5 GHz or Universal Ku band 13 75 to 14 5 GHz output The Unit comes in a single weatherized housing rated for outdoor use The Unit has either an N Type or a F type female connector input a WR75 waveguide with grooved flange output and optional MS connector for DC power input The Unit is operated by 48 V DC power Range 36 to 60 V input The Unit has the function of Monitor and Control which is complied with FSK communication and RS 232C interfaces NJT8319 series Instruction Manual Page 5 New Japan Radio Co Ltd The Unit has the following line up IM T8319 Rev 01 NJT83 1 9UNMK Lo M amp C Option Non Suffix N A K FSK communication M amp C Equipped R RS 232C Interface M amp C Equipped DC Input Connector Non Suffix

IM-T8319 - New Japan Radio

Contents

Download Pdf Manuals

Related Search

Related Contents