Manual
Contents
1. DIMMER SHUTTER FUNCTION MACRO ACTIVE AFTER 5S Cleaning Due to fog residue smoke and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light output 1 Use normal glass cleaner and a soft cloth to wipe off the outside casing 2 Clean the external optics with glass cleaner and a soft cloth every 20 days 3 Always be sure to dry all parts completely before plugging the unit back in Cleaning frequency depends on the environment in which the unit operates i e smoke fog residue dust dew Trouble Shooting Listed below are a few common problems the user may encounter with solutions Unit not responding to DMX 1 Check that the DMX cables are connected properly and are wired correctly pin 3 is hot on Some other DMX devices pin 5 may be hot Also check that all cables are connected to the right connectors It does matter which way the inputs and outputs are connected Unit does not respond to sound 1 Quiet or high pitched sounds will not activate the unit If problems are not resolved contact Your dealer for service Specifications Model Rocket 2R Laser Scanner Working Position Any safe working position Voltage 90 250V 50 60Hz Power 220W Lamp YODN 132W 2R lamp DMX Channel 21 17 channel mode Protection Rating IP20 Color 14 colors white Gobo 17 gobos white Prism 3 facet prism Beam angle 3 Feature Multi effect lumi2. User Manual TourPro Rocket 2R Laser Scanner Introduction Unpacking Thank you for purchasing Rocket 2R Laser Scanner Every unit has been thoroughly tested and shipped in perfect condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your unit for any damage and be sure all accessories necessary to operate the unit has arrived intently In the case damage has been found or parts are missing please contact the manufacturer or your dealer for further instructions Do not return this unit to your dealer without any warning Read all cautions and warnings prior to operation of this equipment Protection Against Fire 1 Maintain a minimum of 1 50cm distance from any type of flame 2 Replace fuse only with the specified type and rating 3 Do not install the unit to close a heat source 4 Make sure cable are properly secured away from unit movement Fire 5 Maximum surface operating temperature 80 Protection Against Electrical N 1 Disconnect power before servicing 2 The unit must be earthed electronically grounded Electrical Protection Against Mechanical Hazards O 1 Use safety chain when hanging unit O 2 Use quality clamps or bolts when positioning unit 3 Do not open unit while it is on risk of electrical shock Mechanical PLEASE recycle the shipping carton whenever possible General Instructions To optimiz
3. e the performance of this product please read these operating instructions carefully to familiarize you with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Features eMulti Colors e Master Slave synchronization eColor Strobe e LED operation menu eElectronic Dimming 0 100 e DMX 512 protocol eDaisy Chain Units together in DMX Mode e With Dot Matrix e With Sound Control Safety Precautions e Be sure that the local power outlet match that of the required voltage for your unit e Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short e Disconnect from main power before making any type of connection e Do not remove the cover under any conditions There are user serviceable parts inside e Never operate this unit when its rear cover is removed e Never plug this unit into a dimmer pack e Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall e Do not attempt to operate this unit if it becomes damaged e During long periods of non use disconnect the units main power e Always mount this unit in safe and stable matter e P
4. erent colors e DMX control mode This function will allow you to control each individual units traits with a standard DMX 512 controller e Master slave mode One unit will work as the master in the one of the above three modes other units in the chain will work in synchronization towards the master e Sound control The unit will react to sound chasing through the built in programs DMX Mode Operating through a DMX controller give the user the freedom to create their own programs tailored to their own individual needs This function also allows you to use your units as spot lights 1 This function will allow you to control each individual units traits with a standard DMX 512 controller 2 The unit has 21 17 two DMX channel modes to operate Please see DMX channels function description value for the DMX traits 3 Torun your unit in DMX mode plug in the unit via the XLR connections to any standard DMX controller Set your desired DMX address following the setup specifications that come with your DMX controller CONTROL BOARD Main Control Menu The control board on the fixture base is your interface to access and control all HHH functions on the unit its digital display gives you a code vide of functions and options as below 4 v MENU UP DOWN ENTER Menu Map A001 DMX Add e A512 17Ch Ch el Mod annel Mode 1 Ch Show Mode Sound Slave Mode Master Black Out Ne _ oa er 0 100 MENU Yes Back Ligh
5. naire beam scanner laser simulator Operation panel LED display Inner box G W 9 5Kgs Inner box dimension 450 350 360mm Master box G W 21kgs Master box dimension for 2 lights 690 470 390mm Warranty 1 Year Note All information is subject to change without prior notice 10
6. ower supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the point they exit from the unit e Cleaning unit should be cleaned only as recommended by the manufacturer See Cleaning for details e Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat e The unit should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibits s marked change in performance DMX Linking To ensure proper DMX data transmission when using several DMX units try to use the shortest cable path possible The order in which units are connected in a DMX line does not influence the DMX addressing For example a unit assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a unit is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Operating Instructions Operating Modes You can use the unit in 4 ways e Auto Mode The unit will automatically chase through the diff
7. t UM n L y On Off Temp 20 200 C 0 999 Firmware Version V1 01 Fact Default A Yes Warm note Press lt Menu gt to enter system then press lt Enter gt for 3sconds to enter hide menu this function allows you to adjust fine position from value 127 to 127 for below devices 427 127 HIDE MENU Value Gobo offset 427 127 Value Shutter offset 427 127 Value Prism offset 497 427 Value RPrism offset 427 427 DMX Channel Chart MODE CHANNEL VALUE FUNCTION PAN PAN SHAKING Hx IH EO b TILT TILT SHAKING i PAN FINE 0 255 Pan Fine 16 bit TILT TILT FINE 0 255 Tilt Fine 16 bit PAN SHAKING Pan Shaking Movement Slow To Fast TILT SHAKING pom O Tilt Shaking Movement Slow To Fast COLOR Tze e 16 20 Color4 21 24 Color5 SS Color1 white Do ea E 122 124 Color14 129 190 Color backward rotation Fast Slow GOBO EA O 15 22 Gobo2 23 29 Gobo3 s 4 PATTERN Es 170 178 Pattern Macro 20 196 203 Pattern Macro 23 230 237 Pattern Macro 27 238 246 Pattern Macro 28 247 255 Pattern Macro 29 FORWARD BACKWARD PATTERN ROTATION Tze sp PATTERN PAN TILT ROTATION Tze TT zar PATTERN ZOOM d 0 127 Pattern Zoom Manual PAN PATTERN MOVEMENT i Ize Tier TILT PATTERN MOVEMENT Tze OS rr 10 ECCENTRI ECCENTRI SHAKING PRISM PRISM ROTATION
Download Pdf Manuals
Related Search