HomeLink® System Programming for Genie®
Contents
1. HomeLink System GENE Programming for Genie When programming it helps to clear out your HomeLink by pressing and holding the first and third buttons down until the indicator on the HomeLink blinks slow then fast about 20 seconds then release both 4 bis buttons If there is something already programmed to your HomeLink do i not clear it unless you are able to reprogram what is already on there es First Train HomeLink to any Genie Intellicode Remote You will need to start with this step for each new opener head HomeLink button combination It is also recommended to consult the car s owner s manual as individual auto manufacturers and models may have specific requirements related to that vehicle gt e gt SA poo ae L l Choose a button on a Genie ntellicode remote not yet programmed to your operator The only reason to use a button not yet programmed to your operator is to keep the door from moving up and down during programming There is no issue if you have the button already programmed to the operator If you have chosen the remote shown right please follow the steps below before continuing to Step 2 If this is not your remote continue directly to Step 2 on the next page a Please check the date code and software revision stamped on the back Software version 2 0 3 may not be compatible with all versions of HomeLink If your remote has this software and you cannot program to2. HomeLink you can use another remote in this same style with a different software revision or any of the Genie remotes shown in the lineup above Please contact Technical Service for additional support Software versio b When you press your chosen button if the LED light that shows up in ___ LED Lights this remote is currently red in color skip Step c and continue directly to Step 2 on the next page c When you press your chosen button if the LED light that shows up in in this remote is currently green hold the button you have chosen until both a red and green LED light show together Once they are both lit let go and quickly press and release the chosen button two 1 times The next time you press it it should be red A GENE HomeLink System Programming for Genie continued Choose the button on your HomeLink that you want to use to open your door If you are using one of the remotes shown below continue with Step a If you are not using one of these remotes below continue to Step b at the bottom a If you are using the three button remote shown right From the previous Step 1 c please hold the same button you changed to the red LED for approximately 10 seconds prior to pressing your Home Link button until both a red and green LED light show again on this remote Once both the red and green LEDs light up then press your HomeLink button down as well holding both sets of buttons down un
3. a Genie Opener 1 Press and hold the program button prem until the round blue LED is on release the button The long LED will flash purple 2 Press the desired HomeLink button for one second and release Press that same button again for one second and release The round LED and long LED will both turn blue and then turn off 3 Pressing the HomeLink button again will cause the garage door to move NOTE If you cannot find your program button on the power head see the user manual or visit the Genie website for additional assistance HomeLink System Programming for GENIE Models IntelliG 1000 IntelliG 1200 TriloG 1200 TriloG 1500 GPower 900 Manufactured before November 2011 The label shown right is on the back of the powerhead Use this instruction if the first 5 digits of the serial number gt szumi from this label is 11290 or smaller FOR HELP CALL 1 7 VOLTAGI CODEC HOMEER TTHE GENIE COMPANY sen Residential Dogs Opergior ee See G S C US LISTED Ne 366 WED UV VAT OODLE IN 800 35 GENIE OR WW W GENIECOMPANY COM Programming HomeLink to a Genie Opener 1 Press and hold the program button u until the round blue LED and the long blue LED i are on release the button The round blue LED will be on 2 Press the program button once eS the long purple LED will begin flashing A PRGM 3 Press the desired HomeLink button for one second and release Press that same button ag
4. ain for one second and release The long LED will flash blue i and then turn off a 4 Pressing the HomeLink button again will cause the garage door to move NOTE If you cannot find your program button on the power head see the user manual or visit the Genie website for additional assistance GENIE HomeLink System Programming for GENIE Models IntelliG 1000 IntelliG 1200 TriloG 1200 TriloG 1500 GPower 900 Manufactured before July 2011 Learn Window The label shown right IS On the back of LOR TORRE THE GENIE COMPANT aly the powerhead Use this instruction 4ny2s pOBesgor N AMP the frst 5 digits ofthe serial number gt saa nuna a from this label is 11188 or smaller ANY COM Programming HomeLink to a Genie Opener 1 Press and hold the program button until the round blue LED and the long blue LED I are on release the button The round blue LED will be on 2 Press the program button once e the long purple LED will begin raeng fi 3 Press a previously learned itchionde 2 transmitter button from model G3T pictured right one time Both the long and round LEDs flash purple ih amp 4 Press the desired HomeLink button for one second and release Both the long and round LEDs go solid purple le 5 Press the desired HomeLink button again for one second and release Both the long and round LEDs change from solid purple to solid blue fl and then go out J 6 Pressing t
5. he HomeLink button again will cause the garage door to move NOTE If you cannot find your program button on the power head see the user manual for your opener or visit the Genie website for additional assistance HomeLink System Programming for GENIE Models IntelliG 1000 IntelliG 1200 TriloG 1200 TriloG 1500 Using an Intelligent Wall Console Programming Home Link to a Genie Opener using an Intelligent Wall Console 1 To begin start in the Opener Setting feature of the Intelligent Wall Console menu To access this menu press the button circled below Scroll through the menu using the arrows to find heading Opener Setting Press the checkmark in the lower right of the screen Choose the Opener number you are using Opener 1 Press the checkmark Use the arrows to scroll to Learn Remote Press the checkmark The screen will now read Learn Active indicating the opener is now ready to receive signals from a remote a 2 Press the desired HomeLink button for one second and release Press that same button again for one second and release The round LED and long LED will both turn blue and then turn off 3 Pressing the HomeLink button again will cause the garage door to move A GENIE HomeLink System Programming for GENIE Models ChainLift 600 BeltLift 600 ChainLift 800 BeltLift 800 ReliaG 600 ReliaG 800 Programming HomeLink to a Genie Opene
6. r 1 Press and release the learn code button CG the red LED will begin to blink CODE 2 Press the desired HomeLink button one time The red LED will stop blinking and stay on 3 Press the desired HomeLink button one more time The red LED will go out 4 Pressing the HomeLink button again will cause the garage door to move NOTE If you cannot find your program button on the power head see the user manual for your opener or visit the Genie website for additional assistance If you are using one of these remotes or F with Learn Buttons that look like the above be sure that you find and follow the notes on page 2 under Training HomeLink to an Intellicode Remote HomeLink System Programming for Older Genie Models If your learn button looks like this Radio Programming Home Link to a Genie Opener 1 Press and release the learn code button the red LED will begin to blink 2 Press the desired HomeLink button one time The red LED will stop blinking and Stay on 3 Press the desired HomeLink button one more time The red LED will go out 4 Pressing the HomeLink button again will cause the garage door to move NOTE If you cannot find your program button on the power head see the user manual or visit the Genie website for additional assistance If you are using one of these remotes or F with Learn Buttons that look like the above be sure that you find and follow the no
7. tes on page 2 under Training HomeLink to an Intellicode Remote
8. til the indicator on the Home Link blinks slow and then fast Once it goes fast release both buttons You are now ready to program your HomeLink to an opener In the following pages please find the document that suits your situation and continue programming If you are using the one button remote shown right Please hold the button for approximately 10 seconds prior to pressing your HomeLink button then press your HomeLink button down as well holding both sets of buttons down until the indicator on the HomeLink blinks slow and then fast Once it goes fast release both buttons You are now ready to program your HomeLink to an opener In the following pages please find the document that suits your situation and continue programming LED Lights Hold down both the remote button and your HomeLink button at the same time As you hold both buttons down the indicator on your HomeLink should blink slow then fast Once it goes fast release both buttons HomeLink System Programming for GENIE Models IntelliG 1000 IntelliG 1200 TriloG 1200 TriloG 1500 GPower 900 ReliaG 650 ReliaG 850 Manufactured after November 2011 The label shown right IS On the back of CEEE THE GENIE NA the powerhead Use this instruction A N 1E the first 5 digits of the serial number gt sizsmezs o UL usuisteD gt a i i TiN MUNN from this label is 11291 or greater ANY COM FRE Programming HomeLink to
Download Pdf Manuals
Related Search