instruction manual - Airguns Of Arizona
Contents
1. XSi GU INSTRUCTION MANUAL HIGHPRESSURE HANDPUMP MANUAL INTRODUCTION The FX pump is designed manufactured and tested by FX Airguns AB in Sweden There are two patented systems The first of them is the 3 stage handpump that is capable of pressures up to 250 bar 3600 psi with ease The latest invention is a 4 stage turbo handpump It has an unique gearing system that gives you the opportunity to gear down when it gets tough It allows the user to choose if they want high volume 300 cc with lower pressure or low volume 200 cc with higher pressure Both are equipped with a exceptional two stage filtration system that ensures that both moisture and and particles are eliminated from the compressed air Please visit our website www fxairguns com to check out the complete fx range of products Safety instructions and warnings e For use only with precharged airguns e The pump requires a reasonable amount of physical exertion If you have any existing medical conditions please check with your doctor prior to use e Never exceed the manufacturer s stated filling pressure e The maximum fill pressure for this pump is 250 bar 3600 psi e Attempting to disassemble abuse or modification of the pump will immediately Invalidate the warranty e Never dismantle the pump in the event of a problem Contact your dealer e Follow the operational instructions of both your airgun and the fx pump before use e Do not lubricate it with2. 0 cc You will feel less resistance when operating but it will take longer to get to wanted pressure Open the valve on the handle to achieve high volume mode 300 cc You will feel slightly more resistance when operating but you will get to wanted pressure faster HINTS AND TIPS Pull the pump handle all the way up while your feet rest at the foot plate A Then push it down until your arms are straight down use your body weight to push the pump all the way down with arms straight and don t forget to bend your knees TROUBLE SHOOTING Problem When I start pumping the manometer Check that the ventilation screw is does not move fully tightened The ventilation screw is tightened but Bad seals in connection between pump the manometer does not move and airtube if so switch to new ones It requires much force to move the Probably the high pressure seal that s pump handle both up and down worn and needs replacement feels like it s sucked down The manometer is going up when I push Probably the none return valve seal down but goes straight back down that s worn and needs replacement when I pull the handle upwards feels like the handle pushes up by itself SERVICE If the tube surface visible in extended position should be dry you shall apply a thin layer of Fuchs Renolit RHF 1 grease or a standard multipurpose grease The pump is equipped with a particle filter that might need replacement after a l
3. al volume Approximately 5 10 more shots at high power 45cc 100 mm Cleaning pellets Recommended for all FX guns Outstanding cleaning without damage to the barrel Available FX Airtubes in 4 5 177 and 5 5 22 Available for all guns with removable airtube Front tubes 240cc 500 mm 185 cc 390 mm 150cc 320 mm 65cc 140 mm 45cc 100 mm Rear bottles 500 cc and 400 cc Maximum fill pressure 220 bar Gauge assembly This gauge suits all our front airtubes You can use it with or without barrel support Charging kit Complete charging device for your scuba tank Features Pressure gauge particle filter replace able and bleed valve Connections Kevlar hose 0 5 m with 1 8 thread FX Fill probe and DIN in scuba end Pump accessories Various adapters DIN to 1 8 External moisture trap easy to service and clean 1 8 connections 122 FX Magazines Spare magazines in calibre 4 5 177 and 5 5 22 State type of gun when ordering 11 FAGERLID e SE 548 92 HOVA e SWEDEN INFO FXAIRGUNS COM s WWW FXAIRGUNS COM
4. harge your airguns Patented three way system gives you 200 bar with ease Maximum fill pressure 250 bar Features Pressure gauge moisture trap particle filter replaceable and bleed valve Connections DIN or Kevlar hose 0 5 m with 1 8 thread FX Pellets High performance domed round tip air rifle pellets Recommended for all FX products Calibre Calibre 5 52 22 weight 1 030 grams 16 grains 4 52 177 weight 0 547 grams 8 44 grains The new Turbo Pump is equipped with a patented 4 stage system It has a unique gearing system that gives you the opportu nity to gear down when it gets rough It allows the user to choose if they want high Or low volume 200 cc with higher pressure Features Pressure gauge moisture trap particle filter replaceable and bleed valve Four stage turbopump volume 300 cc with lower pressure Tube clamp Allows easy addition of a sling strap bipod or other accessory without any modification to the fore end of the stock Suitable for all airtubess with a diameter of 33 mm Unique Gearing system Barrel support Requires newer version air cylinder with raised section on end cap Available for standard 14 mm barrel and shrouded versions 16 mm Replacement end cap is required if an older version of cylinder Is to be used with barrel support Tube extension Add this to your existing airtube for addition
5. oil e Lubricate with FUCHS RENOLIT RHF1 or similar e Never operate the pump for over 5 minutes at a time Overheating may occur Keep hands and other sensitive parts of your body away from the ventilation hole and make sure that other people are not in the way of the ventilation hole when bleeding the moisture trap e Continuously bleed the moisture trap when filling larger airtubes Make sure that threads on the pump adaptors and airtubes are in good shape and not worn before use ASSEMBLY Mount footplate A at the pump base B from beneath with the enclosed allen screws F Tool required Enclosed 3mm Hex Key allenkey If the pump is equipped with a DIN18 H Adaptor jump to page 5 otherwise move on to 3 Make sure that seals are attached to all connections If the pump is equipped with an external moisture trap D you should mount this now to the pump base B at point C Tool required 19 mm wrench spanner not included If a hose is included with the pump mount it at point C or D if External moisture trap is fitted Use a monkey wrench or a 14 mm s key Tool required 14 mm wrench spanner not included Fit whatever connector your rifle is equipped with make sure that it s Threaded with 1 8 connection before wmounting OPERATING INSTRUCTIONS DIN 18 adaptor 1 Attach your airgun adaptor in accordance with your airgun manufacturers Instruction manual Unscrew adaptor H from the pum
6. ong period of use LOCATION DIN 18 Connection Unscrew the Adaptor H and the filter is located in the threaded end Hose with 1 8 connection Filter is located in the end of the hose E between the hose and and the filterhousing If you use a FX Fillbrobe you can aply the filter directly between the fillprobe and the hose filterhousing We use regular 4 5 177 cleaning pellets as particle filter so you can easily get hold of them The FX pumps are other than above maintenance free Keep clean and make sure you bleed the moisture trap properly ACCESSORIES Scopemounts Sport Utility Rings have a unique wrap around FX optics 3 12x44 ir ao design are available in 1 inch diameters fits any Objective Lens Diameter mim scope size low medium or high and comes in Diopter Adjustment Range 2 0 2 0 matte black Reticle Illuminated Red Parallax 30 yds infinity Body Tube Diamater 25 4 mm Total Length 412 mm Muzzle Flip Total Weight 500 g Suits all FX Rifles with Lens Coating Fully Multi coated 12 thread on the muzzle Mounted as standard on the Verminator Addition Shrouded barrel and barrelsupport Available as addition on some of the FX rifles Single Scoped Rifle Case Contoured recessed latches Padlock tabs for added security Strong and ribbed construction Inner dimension 121x27x7 cm 10 FX HANDPUMPS Three stage pump The easiest most convenient and afford able way to c
7. p base and attach this to your Airtube adaptor Close ventilation screw I Attach your air tube with adaptor s to the connector thread H ao A W N Charge your air tube to wanted pressure see 5 5 For hints Note Some airguns steyr Walther etc have cylinders that must not suffer pressure loss when being disconnected after charging To ensure this does not happen please jump to instructions at point 8 Otherwise proceed to point 6 6 Open ventilation screw I quickly This both releases the air lock between The pump and air tube as well as draining the moisture trap of moisture 7 Disconnect your airtube from the pump base then your adaptor from the airtube Your are now ready to use your airtube 8 Carefully open the ventilation screw I for a short time only to allow water to escape 9 If air pressure is lost recharge your airtube with further pumping 10 Disconnect the airtube from the adaptor which should remain within the DIN Connnection H Your are now ready to use your airtube Hose with 1 8 connection 1 Close ventilation screw l 2 Charge your air tube to wanted pressure see 5 5 for hints 3 Open ventilation screw I quickly This releases built up moisture from the moisture trap as well as removing the overpressure in the hose so that you will be able to remove the filling adaptor from your airgun 3 4 STAGE SWITCH Fourstage pumps only Close the valve on the handle to obtain low volume mode 20
Download Pdf Manuals
Related Search