User Manual
Contents
1. This device falls under protection class The power plug must only be plugged into a protection class outlet The voltage and frequency must exactly be the same as stated on the device Wrong voltages or power outlets can lead to the destruction of the device and to mortal electrical shock Always plug in the power plug last The power plug must always be inserted without force Make sure that the plug is tightly connected with the outlet Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Never touch them with wet hands as this could lead to mortal electrical shock Never modify bend strain mechanically put pressure on pull or heat up the power cord Never operate next to sources of heat or cold Disregard can lead to power cord damages fire or mortal electrical shock The cable insert or the female part in the device must never be strained There must always be sufficient cable to the device Otherwise the cable may be damaged which may lead to mortal damage Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time If extension cords are used make sure that the core diameter is sufficient for the required power consumption of the device All warnings concerning the power cords are also valid for possible extension cords Always disconnect from the mains when the devi2. recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents CAUTION N The lens has to be replaced when it is obviously damaged so that its functions is impaired e 9 due to cracks or deep scratches The objective lens will require weekly cleaning as smoke fluid tends to building up residues reducing the light output very guickly There are no serviceable parts inside the device except for the fuse Maintenance and service operations are only to be carried out by authorized dealers Replacing the fuse If the lamp burns out the fine wire fuse of the device might fuse too Only replace the fuse by a fuse of same type and rating Before replacing the fuse unplug mains lead Procedure Step 1 Unscrew the fuseholder on the rearpanel with a fitting screwdriver from the housing anti clockwise Step 2 Remove the old fuse from the fuseholder Step 3 Install the new fuse in the fuseholder Step 4 Replace the fuseholder in the housing and fix it Should you need any spare parts please use genuine parts If the power supply cable of this device becomes damaged it has to be replaced by authorized dealers only in order to avoid hazards Should you have further questions please contact your dealer TECHNICAL SPECIFICATIONS Power supply Power consumption 15W Dimensions Lx W H Weight Fuse Maximum ambient temperature t4 Maximum housing temperatur
3. unauthorized modifications on the device are forbidden due to safety reasons If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock lamp explosion crash etc 5 9 OVERVIEW 6 9 1 Lens 2 Manual focus 3 Housing 4 Fixation screw 5 Mounting bracket 6 Attachment eyelet 7 Jack socket IN 8 Jack socket OUT 9 Fuseholder 10 Power switch 11 Power supply INSTALLATION Overhead rigging DANGER TO LIFE N Please consider the EN 60598 8 17 and the respective national norms during the installation The installation must only be carried out by an authorized dealer The installation of the device has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate catch net This secondary safety attachment must be constructed in away that no part of the installation can fall down ifthe main attachment fails When rigging derigging or servicing the device staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden The operator has to make sure that safety relating and machine t
4. Color ife USER MANUAL X Dreamy Lighting effect INSTRUCTIONS Table of contents INTRODUCTION a nn eee n ja 3 SAFETY INSTRUCTIONS 3 OPERATING DETERMINATIONS 5 5 5 5 OVERVIEW esu Cates Cae be ees eee ees epi tau cee eae iva 6 INSTALLATION 5 kananan a a aaa ee eee 7 Overhead rigging nn 7 OPERATION m a ee ae aces 8 CLEANING AND MAINTENANCE 5 8 Replacing the fuse ii 9 TECHNICAL 5 5 9 You can find the latest update of this user manual in the internet under http kalalife com 2 9 USER MANUAL ColovLife X Dreamy Lighting effect CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing For your own safety please read this user manual carefully before you initially start up Every person involved with the installation operation and maintenance of this device has to be qualified follow the instructions ofthis manual consider this manual to be part ofthe total product keep this manual for the entire service life of the product pass this manual on to every further owner or user of the product download the latest version of the user manual from the internet INTROD
5. UCTION Thank you for having chosen a COLORLIFE X Dreamy if you follow the instructions given in this manual we are sure that you will enjoy this device for a long period of time Unpack your X Dreamy Before you initially start up please make sure that there are no transport damages Should there be any do not take the device into operation and immediately consult your dealer SAFETY INSTRUCTIONS CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wires This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation itis absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems 3 9 If the device has been exposed to drastic temperature fluctuation g After transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Please make sure that there are no obvious transport damages Should you notice any damages on the A C connection cable or on the casing do not take the device into operation and immediately consult your local dealer
6. ce is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord Otherwise the cable or plug can be damaged leading to mortal electrical shock If the power plug or the power switch is not accessible the device must be disconnected via the mains If the power plug or the device is dusty the device must be taken out of operation disconnected and then be cleaned with a dry cloth Dust can reduce the insulation which may lead to mortal electrical shock More severe dirt in and at the device should only be removed by a specialist There must never enter any liquid into power outlets extension cords or any holes in the housing of the device If you suppose that also a minimal amount of liquid may have entered the device it must immediately be disconnected This is also valid if the device was exposed to high humidity Also if the device is still running the device must be checked by a specialist if the liquid has reduced any insulation Reduced insulation can cause mortal electrical shock There must never beany objects entering into the device This is especially valid for metal parts If any metal parts like staples or coarse metal chips enter into the device the device must be taken out of operation and disconnected immediately Malfunction or short circuits caused by metal parts may cause mortal injuries HEALTH HAZARD N Never look directly into the light source as sensitiv
7. e persons may suffer an epileptic shock especially meant for epileptics Keep away children and amateurs Never leave this device running unattended 4 9 OPERATING DETERMINATIONS This device is a lighting effect for creating decorative effects This product is only allowed to be operated with an alternating voltage of 230V 5Hz or 110V 60Hz and was designed for indoor use only This device is designed for professional use e g On stages in discothegues theatres etc Lighting effects are not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for along time without defects Do not shake the device Avoid brute force when installing or operating the device When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own andthe safety of others This device must never be operated or stockpiled in sourroundings where splash water rain moisture or fog may harm the device Moisture or very high humidity can reduce the insulation and lead to mortal electrical shocks When using smoke machines make sure that the device is never exposed to the direct smoke jet and is installed in a distance of 0 5 meters between smoke machine and device The room must only be saturated with an amount of smoke that the visibility will always be more than 10 meters The ambie
8. e ts steady state Number LEDs Please note Every information is subject to change without prior notice 24 06 2005 ColorLife NO 19
9. echnical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time The operator has to make sure that safety relating and machine technical installations are approved by an expert after every four year the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are approved by skilled person once a year Procedure The device should be installed outside areas where persons may walk by or be seated IMPORTANT OVERHEAD RIGGING REOUIRES EXTENSIVE EXPERIENCE including butnot limited to calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and or damage to property The device has to be installed out of the reach of people If the device shall be lowered from the ceiling or high joists professional trussing systems have to be used The device must never be fixed swinging freely in the room Caution Devices in hanging installations may cause severe injuries when crashing down If you have doubts concerning the safety of a possible installation do NOT install the device Before rigging make sure that the installation area can h
10. nt temperature must always be between 5 C and 45 C Keep away from direct insulation particularly in cars and heaters The relative humidity must not exceed 50 with an ambient temperature of 45 C This device must only operated in an altitude between 20 and 2000 m over Never use the device during thunderstorms Over voltage could destroy the device Always disconnect the device during thunderstorms The symbol ess mf determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 0 1 meters This device is only allowed for an installation via the mounting bracket In order to safeguard sufficient ventilation leave 50 cm of free space around the device The housing must never touch surrounding surfaces or objects Make sure that the area below the installation place is blocked when rigging derigging or servicing the fixture Always fix the fixture with an appropriate safety rope The maximum ambient temperature t 45 C must never be exceeded Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Never use solvents or aggressive detergents in order to clean the device Rather use a soft and damp cloth Please use the original packaging if the device is to be transported Please consider that
11. old a minimum point load of 10 times the device s weight DANGER OF FIRE When installing the device make sure there is no highly inflammable material decoration articles etc within a distance of min 0 5 m Mount the device to your trussing system using an appropriate clamp For overhead use always install a safety rope that can hold at least 12 times the weight of the fixture You must only use safety ropes with quick link with screw cap Pull the safety rope through the attachment eyelet and over the trussing system or a safe fixation spot Insert the end in the quick link and tighten the safety screw 7 9 The maximum drop distance must never exceed 20 cm A safety which already hold the strain ofa crash or which is defective must not be used again Adjust the desired inclination angle via the mounting bracket and tighten the fixation screws Connect the fixture to the mains with the power plug The occupation of the connection cables is as follows Cable Pin International Brown Live L Blue Neutral N Yellow Green Earth The earth has to be connected If the device will be directly connected with the local power supply network a disconnection switch with a minimum opening of 3 mm at every pole has to be included in the permanent electrical installation Lighting effects must not be connected to dimming packs DANGER TO LIFE N Before taking into operation for the firs
12. t time the installation has to be approved by an expert OPERATION After you connected the effect to the mains the X Dreamy starts running With the POWER switch you can switch the device on and off Ontherear panel ofthe X Dreamy you canfind two jack sockets which can be used for connecting several devices in order to operate them synchronously Connect the OUT socket via a mono jack connection cable with the IN socket of the next device CLEANING AND MAINTENANCE The operator has to make sure that safety relating and machine technical installations are inspected by an expert after every four years in the course of an acceptance test The operator has to make sure that safety relating and machine techinical installations are inspected by a skilled person once a year The following pints have to be considered during the inspection 1 All screws used for installing the devices or parts of the device have to be highly connected and must not be corroded 2 There must not be any deformations on housings fixations and installation spots ceiling suspension trussing 3 The electric power supply cables must not show any damages material fatigue e G porous cables or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed DANGER LIFE Disconnect from mains before starting maintenance operatioon We
Download Pdf Manuals
Related Search