TireMoni TM-100-210 Manual E V2.09 110222
Contents
1. 14 bar 2 psi Temperature 2 C Operating voltage 3V DC temperature 1 4 years or approx 50 000 km Dimensions Diameter 20 5 mm X Height 20 mm Weight 10 g 1 Specifications of display unit Frequency 433 92 MHz Reserve voltage 3V DC 1 2 years or approx 25 000 km Operating 20 C 85 C temperature Dimensions Width 75 mm X Height 91 mm X Depth 22 mm Weight 100 g 34 23 02 2011 TireMoni manual v2 09 TireMoni TM 100 Tyre pressure monitoring system Important safety instructions Before starting the tyre pressure monitoring system for your own safety please imperatively read and observe these important safety instructions Monitor installation e Attach the LCD monitor display unit at a place not interfering with the driver s field of vision e Make sure to position the LCD monitor in such a way that it cannot fall down during the ride e Mind your driving safety when reading the pressure temperature values from the LCD monitor e Do not attempt to disassemble or repair any parts of the system by yourself Any failure to comply will immediately and irrevocably result in losing the manufacturer warranty Sensor installation e Road traffic regulations require that no parts protrude beyond the rim contour For this reason please assemble the sensors on short valves in such way only that the sensor stays within the rim contour For safety reasons it is prohibited to run th2. As shown by research findings already when driving at an air pressure lower than 20 below the set value the tyre life is reduced by up to 50 For an optimum utilisation of the available tyre life the correct tyre pressure thus represents a precondition please observe your vehicle manufacturer s requirements to determine the correct tyre pressure e Increases profitability The result of all the advantages given is Monitoring the tyre pressure using the TireMoni tyre pressure monitoring system offers more benefits to you than you may expect at first glance Properties of TireMoni Checkair TireMoni WTPMS Wireless Tire Pressure Monitoring System is an effective tool for achieving maximum service life and improved operational safety the new WTPMS standard TireMoni tyre pressure control Technologically TireMoni is the leading solution in the field of radio tyre pressure monitoring for light to and heavy commercial vehicles and recreation vehicles By constantly enhancing the design and manufacturing technologies TireMoni helps improving safe driving while reducing operational cost as a secondary effect the environment gets relieved due to reduced fuel and tyre consumption The most important milestone when developing TireMoni WTPMS was introducing the highly integrated valve cap sensor This extremely low weight and compact sensor was especially designed as to allowing a simple and quick installation This means Neglecting tyre
3. The manufacturer is not liable for indirect consequences and damages The warranty period is not extended or renewed by any possible repairs Claims under this warranty are only accepted if the instrument is returned complete and free of charge to the dealer distributor or manufacturer WEEE Disposing of Elecirical Instruments household waste You are obliged to dispose of such electronic instruments separately Please consult your local authority about the possibilities of suitable disposal With the separate disposal you are returning obsolete devices to a suitable form of recycling This way you are helping to avoid potentially hazardous substances to contaminate our environment Ki Instruments that are marked with the marking shown must not be disposed of in Tiremoni manual v2 09 23 02 2011 35 TireMoni TM 100 Tyre pressure monitoring system Specifications TM 100 Sensor specification Frequency 433 92 MHz Measuring range 0 4 bar 0 60 psi Precision Pressure 0 07 bar 1 psi Temperature 2 C Operating voltage 3V DC Operating 40 CT 85 C temperature Reserve energy 1 4 years or approx 50 000 km Dimensions Diameter 20 5 mm X Height 20 mm Weight 10 g 1 Specifications of display unit 433 92 MHz 3V DC 1 2 years or approx 25 000 km temperature Width 75 mm X Height 91 mm X Depth 22 mm 100 g Specifications TM 210 Sensor specification 433 92 MHz 0 11 bar 0 160 psi Pressure 0
4. TireMoni TM 100 Tyre presure control system Supplier tpm systems AG Romanshornerstr 117 CH 8280 Kreuzlingen Switzerland Fon 41 71 698 6480 Fax 41 71 698 6481 HRA Thurgau CH 170 3 028 628 4 Distributor tpm UG haftungsbeschrankt Gewerbepark 26 D 86687 Kaisheim Fon 49 9099 966 4966 Fax 49 9099 966 4969 email support tiremoni com TireMoni Checkair TM 100 and TM 210 Tyre pressure monitoring system Tire Moni Checkaif m oo At one glance fully informed a good feeling Revision v2 09 2011 Table of contents TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS PREVENTIVE MEASURES MAIN FUNCTIONS OF TIREMONI CHECKAIR PROPERTIES OF TIREMONI CHECKAIR 1 Installation 2 Operational concept 3 Reliable and robust OPERATING ELEMENTS OF DISPLAY UNIT DESCRIPTION OF THE GRAPHICAL USER INTERFACE STARTING UP System diagram Installation __ Installation instructions __Installing the display unit __Installation of the pressure sensors __ Inserting batteries into the sensor __ Anti theft protection for sensor optional __Installing the display unit at the front screen or dashboard INSTRUCTIONS FOR USE 1 Basic display unit functions _ Position of operating elements 2 Screen content and basic functions 3 Advanced settings SYSTEM OPERATION 1 initialisation 2 Main screen 3 Power save mode sleep mode 4 Abnormal tyre pressure or temperature __ Tyre pressure below lower warning threshold __Ty
5. a warning every time the pressure rises by another 0 1 bars These warnings will stop as soon as the pressure i e by venting air is again below the set warning threshold Attention If the warning is given you should first assess the situation to ensure safe stopping only then you should check the tyres as quickly as possible Tyre temperature above upper temperature warning threshold When the temperature rises above the set upper warning threshold default setting 70 C the display unit beeps ten times showing the alert HiT at the wheel position concerned This is shown in the figure to follow The temperature of the wheel rear left is too high Flashing In this example Rear Left R L H the temperature continues to rise the display unit gives a warning every time the temperature rises by another 1 C The warning stops as soon as the temperature falls again below the set warning threshold Attention If the warning is given you should first assess the situation to ensure safe stopping only then you should check the tyre thoroughly Tiremoni manual v2 09 23 02 2011 27 TireMoni TM 100 Tyre pressure monitoring system 3 Power save mode sleep mode For an optimum utilisation of the battery capacity the system display unit and sensors has an intelligent energy management the display and sensors automatically pass into the sleep mode when no activity is detected for more than 10 minutes In this mode the display is sw
6. ar left R L Rear right R R 8 23 02 2011 TireMoni manual v2 09 TireMoni TM 100 Tyre pressure monitoring system 5 Description of alerts and displays Status 1 Switching on Advising that the system is A beep and switching on the now switched on backlight 2 Pressure below the To serve as warning that the Three beeps ten time ina lower warning threshold pressure is too low row and switching on the backlight during three seconds 3 Pressure continues to When the pressure is below Three beeps ten time in a fall by 0 1 bars the lower warning threshold row and switching on the there will be a new warning backlight during three per 0 1 bars as a reminder seconds Pressure is above the To serve as a warning thatthe Three beeps ten timein a upper warning threshold pressure is too high 4 row and switching on the backlight during three seconds 5 Pressure keeps on When the pressure is above Three beeps ten time Ina rising by 0 1 bar above the upper warning threshold row and switching on the a the warning threshold there will be a new warning backlight during three per 0 1 bars as a reminder seconds When the temperature To serve as a warning that the Three beeps ten time Ina is above the warning temperature is too high row and switching on the a threshold backlight during three seconds Main screen displayed System starting sequence One beep and switching on completed the backlight during one second Back from t
7. ars Adjustable Upper and lower warning thresholds for pressure and upper threshold for temperature can be adjusted by the user Warnings Any abnormal tyre condition pressure or temperature can be easily read from the large 3 5 LED monitor and gets signaled by beeps Reliable and robust Anti theft protection for the sensor The pressure sensors can be protected against unscrewing using a fixing stop In any case of loss or damaging replacement sensors are available so that the down times for the system stay minimal Safe radio communication ensured due to specific signal processing Strict live tests proving its reliability The sensors have a pressure measuring range of 4 bar 60 psi TM 100 or 12 bar 160 psi TM 210 Corrosion protection The sensor housing has a rust proofing coating which is used for extending the sensor operating time We additionally recommend mounting using a suitable installation spray 23 02 2011 TireMoni manual v2 09 TireMoni TM 100 Tyre pressure monitoring system gt Make sure that the display unit can receive signals from the sensor The distance between the display unit and the sensor may be up to 20 meters however the actual range of coverage may be lower due to interferences Make sure that the relays are fitted with batteries Make sure that the batteries have been inserted with the correct polarity Please check whether the battery is discharged The battery may be dead aft
8. e mechanism to avoid any interference from other signal sources 9th The tyre temperature may vary either upwards or downwards depending on the many different influence factors i e ambient temperature travelling speed solar radiation rising temperatures cause an increased tyre pressure whereas the pressure will fall when the temperature is falling Adhesive plate 10th The tyre pressure is getting lower over the years due to diffusion this phenomenon is not due to but merely displayed by TireMoni In any case TireMoni only shows the tyre pressure which is actually available 11th Should you have any questions or issues with reference to your TireMoni product which are not being responded to in this manual please contact your nearest TireMoni distributor or check out our website www tiremoni com FAQ html Main functions of TireMoni Checkair Cigarette lighter cable The tyre pressure control system RDKS or TPMS is an efficient and cost effective response to many current safety issues related to motor vehicles Using a tyre pressure monitoring system avoids driving with too little air pressure available in the tyre and helps reducing fuel consumption These are your benefits e Improved ride qualities and enhanced handling The air pressure represents an essential element influencing the road performance of your vehicle e Reduces the risk of blowouts Selecting the appropriate tyre pressure is critical to safe driving especially dur
9. e mounting frame A Adhesive plate B Mounting frame w vacuum cup Attaching the mounting frame at the display unit A First hook in the mounting frame at the display unit Tiremoni manual v2 09 23 02 2011 17 TireMoni TM 100 Tyre pressure monitoring system TireMoni TM 100 Tyre pressure monitoring system B Then firmly tighten the screw Note e Do not spill any liquids across the display unit For attaching the device a flat and clean is surface is required When cleaning please avoid touching the screen surface Hold the display unit at its housing only The display unit should be mounted in an upright position A position pointing upwards may cause failures Optional Cigarette lighter cable Another operating option is using the cigarette lighter cable terminal in this case no batteries are required A Cigarette lighter cable terminal in the display unit VW aa DI B Plug cigarette lighter cable D Attach the display unit at the front screen or dashboard TireMoni manual v2 09 Tiremoni manual v2 09 23 02 2011 23 02 2011
10. e signals from the sensors The display unit beeps once and shows the last received before the sleep mode pressure values The figure to follow shows the condition available after starting up Tiremoni manual v2 09 23 02 2011 11 TireMoni TM 100 Tyre pressure monitoring system Note 1 When the batteries are becoming exhausted the charging condition is displayed as described further down 2 Before taking the next step the display unit needs to be switched on 3 Please observe the correct polarity when inserting the batteries 4 The system was designed to allow easy handling There is no need for switching off the display unit It is even recommended to always keep the display unit switched on If not used the device automatically passes into a sleep mode for saving electricity Installation of the pressure sensors The sensors are consecutively numbered and each sensor has its respective position it needs to be mounted to Depending on the number of wheels monitored every single sensor number corresponds to another wheel position When inserting the batteries please make sure not to confuse the sensor caps The relays sensor allocation table informs you at what wheel position the different sensors are to be mounted Please find the allocation table below FR R R F L R L F L stands for Front Left F R stands for Front Right R L stands for Rear Left R R stands for Rear Right Note When inserting the bat
11. e system with the sensors protruding from the rim contour Disregarding of this provision will automatically void your operating license e It is recommended to install sensors on suitable metal valves which are screwed in place Suitable length so that the sensor does not protrude from the rim and suitable valve type so that the forces are held by the valve case and not the gasket e g Valve series ASC made by Alligator see htip shop tiremoni com e tis recommended to have the first time installation done by a professional e Check the tightness of the sensors after installation by pouring some water across the valves and then checking for any discharge of air bubbles e It is recommended to install sensors using a suitable anti corrosion spray or copper paste to prevent corrosion from moist and salt e tis recommended to rebalance the tyres subsequent to sensor installation e When the LCD monitor is not operated please immediately remove the sensors In case the sensors remain installed while the LCD monitor is out of operation you are compromising your own safety and the system function can no longer be guaranteed International Deutsch TireMoni TM 100 TM 210 User Handbuch www tiremoni de Downloads html English TireMoni TM 100 TM 210 User Manual www tiremoni eu Downloads html Francais TireMoni TM 100 TM 210 Manuel d Utilisation www tiremoni fr Downloads html Italiano TireMoni TM 100 TM 210 Istruzione d Uso www t
12. east 10 seconds before re inserting the battery Otherwise the sensor may not start properly Tiremoni manual v2 09 23 02 2011 13 TireMoni TM 100 Tyre pressure monitoring system TireMoni TM 100 Tyre pressure monitoring system C Screw the sensor cap back on e Temperature After pressing the Temperature button all tyre temperatures are displayed during three seconds Afterwards the display returns to the main screen Qu fueren 4 Consult the allocation table p 12 to check whether each sensor is mounted at its proper wheel and please make sure not to confuse the sensor caps Both the sensor cap and the sensor itself are labelled with the position marking Backlight Sensor position Front Left F L For reading the device in the dark the backlight can be switched on using this button The backlight is turned off automatically after three seconds Anti theft protection for sensor optional With our anti theft protection the sensors cannot be screwed off The user can decide whether to have this feature installed or not 23 TireMoni manual v2 09 Tiremoni manual v2 09 23 02 2011 23 02 2011 TireMoni TM 100 Tyre pressure monitoring system TireMoni TM 100 Tyre pressure monitoring system Slide the anti theft protection onto the valve B Press longer than 5 seconds When pressing this button longer than 5 seconds the device passes into the mode for adjusting the measuring units and warni
13. elated have gone instead is displayed 30 23 02 2011 TireMoni manual v2 09 TireMoni TM 100 Tyre pressure monitoring system LCD display Front view Description of construction frame Tiremoni manual v2 09 Mute Temperature Backlight SZ Threading receving On off eS the construction frame switch Fixing hook slot Battery cover Terminal for cigarette lighter cable Rear view Fixing screw Mounting frame Angle adjustment Tilt mount Mounting plate Mounting frame 23 02 2011 7 TireMoni TM 100 Tyre pressure monitoring system Sensor description The sensor consists of two parts sensor cap and sensor housing The execution as a valve cap allows quick and easy installation without requiring any technical knowledge Battery cap sensor Threading to be screwed on the valve Sensor status X Status updated Without icon Status not update Temperature unit C Celsius I F Farenheit Battery display Without icon Battery OK Battery empty Battery condition Without icon Battery OK HU Battery empty Mute without icon Sound on p Device mute Status not flashing Device is starting Pressure unit flashing normal operation KPA PSI Pressure Temperature display bars Value for pressure or temperature 2 LaF Pressure too low kg cm H H Pressure too high Wheel position Front left F L H E Temp too low Front right F R Re
14. er a longer service life and we recommend you to replace it Please make sure that you did not confuse your sensor with another system Each sensor has its own ID number and the display unit can only detect and receive the sensors it is associated with and will not accept any other ID numbers F Please remove the sensor battery and put it back in place after a short while approx 30 seconds this will restart the sensor and sign it on in the system G Incase the present information should not provide further assistance to you please contact your TireMoni distributor or our TireMoni support team www tiremoni com FAQ html DOW m Display unit will not quit beeping When the display unit has been operated using almost discharged batteries over a longer period it is possible that the device gets into an undefined state and will not quit beeping In this case please replace the batteries switch off the device and switch it on again after a short while It should then function normally again Display becoming dark When the temperature i e by solar radiation rises above 85 C it is normal for the LCD display to become dark black When the temperature is falling the display gets back to its normal condition When the temperature falls below 25 C the response time of the indicators may increase and the display will respond at a slower rate as usually Display unit in sleep mode When the vehicle is parked or run vibrat
15. he Advising that the system is One beep electricity saving mode now enabled settings now completed the backlight sensor has now been taught in 11 Back to main screen Advising that the settings now One beep after completing the have been completed adjustment mode Tiremoni manual v2 09 23 02 2011 29 TireMoni TM 100 Tyre pressure monitoring system Display unit Battery becoming exhausted The battery in the sensor is consumed by daily use When the capacity falls below a certain value this condition becomes displayed to inform that new batteries shall be used The symbol is given in the figure below ZS Please replace the battery in the display unit once the corresponding message appears to make sure that the system is functioning properly Sensor Battery becoming exhausted The battery in the sensor is consumed by daily use When the capacity falls below a certain value this condition becomes displayed to inform that new batteries shall be used The symbol is given in the figure below In this example Rear Left R L Please change the battery in the sensor as soon this becomes displayed to make sure that the system is functioning properly 28 23 02 2011 TireMoni manual v2 09 TireMoni TM 100 Tyre pressure monitoring system System diagram Optional TireMoni Checkair Installation The display unit can either be operated using batteries or the cigarette lighter cable In the following we will first de
16. ing passenger accommodation or when carrying hazardous material e No more need for manually checking the tyre pressure With multi wheel vehicles much time is required for carrying out the manual tyre pressure control Monitoring the tyre pressure during the ride manually is not possible at all At anytime TireMoni provides you with a unambigous image of the current tyre condition 4 23 02 2011 TireMoni manual v2 09 Tiremoni manual v2 09 23 02 2011 33 TireMoni TM 100 Tyre pressure monitoring system TireMoni display unit Checkair pressure sensor O Ir l Tuy pe 1 pc 4 pc 4 pc pc 4 pc pc CR1632 Lithium battery AAA 1 5V battery 2 1 pc Anti theft Socket wrench 1 pc protection Anti theft rings a 32 23 02 2011 TireMoni manual v2 09 TireMoni TM 100 Tyre pressure monitoring system e Avoids high running cost Due to the consistent radio design and the external sensors only little expenditure is required for installation The running costs are minimised by using replaceable batteries e Reduced down times The real time monitoring continuously delivers the values for tyre pressure and temperature this helps avoiding unexpected break downs due to defective tyre pressures and temperatures e Reduces fuel consumption Per each pressure drop of 0 2 bars the fuel consumption is increased by 1 which makes the tyre pressure an essential factor in terms of fuel consumption e Extends the tyre life
17. ion free over a longer period of time the display unit may pass into the sleep mode in order to save electricity When touching the device or pressing any control knob it will be re enabled immediately Please make sure that the front screen is clean and flat at the very location you wish to mount the display unit otherwise the vacuum cup may not adhere properly and cause the device to come off The tyre pressure varies depending on different influencing factors The tyre temperature is one of the main factors Per 10 C temperature rise the pressure rises by approx 0 25 bars based upon a room temperature of 25 C Tiremoni manual v2 09 23 02 2011 31 TireMoni TM 100 Tyre pressure monitoring system Under normal conditions the sensor batteries can be used for approx 1 2 years the operating time may be reduced due to high driving performances When the battery capacity is getting low this information is displayed on the screen Please replace the battery with a new CR1632 lithium battery Notes about the battery e Please store any batteries beyond children s reach In case of swallowing a battery please consult a physician as quickly as possible Clean the batteries before inserting them using a dry cloth to ensure a good contact Please observe the correct polarity when inserting the batteries away from the sensor towards the sensor e Do not hold the battery with metallic tweezers or tongs this may produce short circu
18. iremoni it Downloads html Nederlandse TireMoni TM 100 TM 210 Gebruikers Handboek www tiremoni nl Downloads html Tiremoni manual v2 09 23 02 2011 3 TireMoni TM 100 Tyre pressure monitoring system TireMoni TM 100 Tyre pressure monitoring system Display mounting frame ist Please select the position of the display unit during installation in such way not to affect the driver in any way istt Make sure that the display unit is firmly attached at the front screen or dashboard 1st2 When reading the display unit please remember not to neglect safe driving 2nd Make sure that the display unit can receive signals from all the tyre pressure sensors 3rd TireMoni WTPMS comes with a unique anti theft protection its sensors may be installed with or without this feature optional 4th Make sure to mount the sensors hermetically sealed If necessary please check the tightness by pouring some water across the valve check for bubbling 5th Install sensors using anti corrosion installation spray or copper paste to prevent corrosion from moist and salt Plate with vacuum 6th In any case of pressure drop please stop immediately and determine the cause of error Cup 7th The display unit automatically establishes connections in the entire system as soon as the vehicle gets started It is normal that the individual pressure values are not immediately updated when the pressure inside the respectivetyres has not changed 8th TireMoni WTPMS possesses som
19. itched off to save electricity When any kind of movement becomes available i e by opening a door or pressing a button the display unit is immediately re enabled The display then looks like below since the measuring values have not been updated yet When there is no activity for more than 10 minutes 4 Abnormal tyre pressure or temperature Tyre pressure below lower warning threshold When the tyre pressure is below the lower warning threshold default setting 3 1 bars the display unit beeps ten times and the related tyre symbol shows Lob alternately with the pressure value to indicate the low pressure value This is represented in the figure to follow The tyre pressure of the wheel rear left is too low In this example Rear Left R L If the pressure continues to fall the display unit gives a warning every time the pressure falls by another 0 1 bars The warnings will stop as soon as the pressure i e by refilling is again above the set warning threshold Attention If the warning is given you should first assess the situation to ensure safe stopping only then you should check the tyres as quickly as possible 26 23 02 2011 TireMoni manual v2 09 TireMoni TM 100 Tyre pressure monitoring system D Close the compartment Press the compartment to the device until it engages E Switch on the display unit Put the switch to the On position as shown in the figure The display unit gets started and receives th
20. its and destroy the battery The battery may explode when handled improperly Do not recharge disassemble or burn batteries Instructions in case of error The checklist to follow should help you identifying and resolving any possible problems arising Please review the installation and operating guidelines before turning to this checklist 1 Displays disappear from are not shown in the display Make sure that the device is switched on Make sure that batteries have been inserted Make sure that the battery capacity is sufficiently high Make sure that the batteries have been inserted with correct polarity When using the cigarette lighter cable please make sure that it has been plugged Please check whether the battery is discharged The battery may be dead after a longer service life and we recommend replacing it Please check whether the system is in sleep mode the system automatically passes into the sleep mode for electricity saving reasons if no activity has been detected for more than 10 minutes However you can re enable the system by slightly striking against or pressing one of the control knobs In case the present information should not provide further assistance to you please contact your TireMoni distributor or our TireMoni support team www tiremoni com FAQ html 1moow Q 2 No connection between the sensors and the display unit The status is displayed as shown below and the respective pressure values r
21. maintenance to the detriment of safety is now a thing of the past Using radio technology the tyre pressure can be read from the user friendly full graphic LCD anytime you like TireMoni WTPMS is available in different configurations which cover all the combinations of commercial vehicles such as transporters motor homes caravan trailers buses agricultural commercial vehicles etc Tiremoni manual v2 09 23 02 2011 5 TireMoni TM 100 Tyre pressure monitoring system Installation Do it yourself D I Y TireMoni can be installed in a very short time It is recommended to have the first time installation done by a professional Please note Sensors should be installed on metal valves of suitable length Sensors must not protrude from the rim contour Wireless Design Installation without laying cables The radio communication between the sensors relays and the display unit makes installation fast and easy Battery operated The display unit the relays and the sensors are run by batteries The charging condition of all the batteries can be read from the display unit Low weight and compact sensor The sensors are very small and low weight and they have specific highly integrated electronics Operational concept Graphical user interface Plain full graphic display providing you with a quick capture of the tyre condition Real time High precision monitoring of the pressure and temperature in real time precision better than 0 1 b
22. needs to be replaced with a replacement sensor only replacement sensors can be taught using this procedure this will not work with original sensors Replacement sensors are available with your distributor or directly at www tiremoni com Before switching on the display unit please press the button and then keeping pressing the button switch on the device This causes the device to pass into the learning mode and to display LEN Please now insert the battery into the replacement sensor At completion of the learning procedure the display unit will again beep Note This function requires a teachable replacement sensor the procedure will not work with an original sensor Should you attempt this using an original sensor all that would happen is hearing three beeps for 30 seconds 24 23 02 2011 TireMoni manual v2 09 TireMoni TM 100 Tyre pressure monitoring system Inserting batteries into the sensor A Unscrew sensor caps S d om i B Insert lithium battery and observe correct polarity see figure The display unit now receives signals of the related sensor and then indicates the pressure value After inserting the battery first 0 00 becomes displayed since the sensor has not been mounted yet The display content is as represented below Flashing In this example the sensor is shown R L Rear Left Note After removing the battery please allow the sensor to be battery free for at l
23. ng thresholds This is described hereinafter The symbols are used to select the measuring units and to increase or decrease the values for the A warning thresholds Pressing the Mute button will take you to the next adjustment point respectively After completing all settings the display unit passes into normal operation by emitting a short beep The available measuring units for the pressure are PSI gt KPA BAR gt kg cm The available measuring units for the temperature are degrees Celsius C and Fahrenheit F C D E SEE Un E Adjust pressure display Adjust temperature display units units Ge D D SEE HP R Adjust lower warning 45 m f theshold RA Q24 wl Adjust warning threshold for Adjust upper pressure een a EECH In this example Rear Left R L 22 23 02 2011 TireMoni manual v2 09 Tiremoni manual v2 09 23 02 2011 15 TireMoni TM 100 Tyre pressure monitoring system TireMoni TM 100 Tyre pressure monitoring system B Please arrange the anti theft protection in such way that the ring is engaging in the Mute press shortly once sensor bottom ng Measuring units and warning thresholds press long A Press shortly When the tyre pressure or the temperature comes into an abnormal state the driver hears beeps When pressing the Mute button the acoustic warning is switched off and only the warnings in the display are visible When pressing the Mute button once mo
24. re the beeps are re enabled C Screw the socket screw onto the threading to be used for attaching the anti theft protection The sensor is now protected against screwing off Do not over tighten to avoid any valve damage D After installing all four sensors please use some water to check for any leakage in the sensors and valves by pouring some water across the valve and checking for air bubbling E Itis up to the user whether to have the anti theft protection installed or not In the negative case the steps A C and D can be skipped 16 23 02 2011 TireMoni manual v2 09 Tiremoni manual v2 09 23 02 2011 21 TireMoni TM 100 Tyre pressure monitoring system Instructions for use 1 Basic display unit functions Position of operating elements Mute Set measuring units Set warning thresholds Temperature Antenna Backlight LCD display 2 Power Switch Switch on the display unit as indicated above The device gets started and will display the last measured values before receiving data from the sensors Main screen This is an example the actual pressure values and configuration may differ 20 23 02 2011 TireMoni manual v2 09 TireMoni TM 100 Tyre pressure monitoring system Installing the display unit at the front screen or dashboard Installing the mounting frame The package comes with two mounting frame holders Please select the option which best suits your needs and screw it onto th
25. re pressure above upper warning threshold __Tyre temperature above upper temperature warning threshold __ Display unit Battery becoming exhausted __ Sensor Battery becoming exhausted 5 Description of alerts and displays ADDITIONAL INFORMATION INSTRUCTIONS IN CASE OF ERROR PACKAGE CONTENTS SPECIFICATIONS TM 100 SPECIFICATIONS TM 210 DECLARATION OF CONFORMITY CONDITIONS OF WARRANTY WEEE DISPOSING OF ELECTRICAL INSTRUMENTS 2 23 02 2011 Oo O OO OO OD JO OO OO oF P P Go ND WWWOWWODNNMDNNMNNNNNNNNNNONONNH ch ch ch Or PM OO oO Oo OO JJ Oo Oo OO Om OO P OO OO OO Jk Go h 35 35 TireMoni manual v2 09 TireMoni TM 100 Tyre pressure monitoring system Declaration of Conformity This product is in its construction and in its operating characteristic conforming to the applicable European directives as well as additional national requirements The conformity has been proven The declaration of conformity can be obtained with tom UG Gewerbepark 26 D 86687 Kaisheim or with the responsible importer Conditions of Warranty In accordance with legal rules this instrument is subject to a warranty period of 24 months from date of order A copy of the sales slip is sufficient proof of purchase in case of a complaint under warranty Damages that can be ascribed to wear transport overloading neclecting the operating manual or inappropriate handling will not be covered under this warranty The same holds for expendables e g batteries
26. scribe the battery operation option Please observe the following steps for starting the relays display unit and sensors Installation instructions 1 Insert the batteries into the display unit 2 Switch on the display unit 3 Insert the batteries into the sensors 4 Screw the sensors instead of the valve caps onto the corresponding wheels Installing the display unit Battery operation A Unpack the batteries provided i AAA I AAA Tiremoni manual v2 09 23 02 2011 9 TireMoni TM 100 Tyre pressure monitoring system B Open the battery compartment To do so please press the lock downwards as shown in the figure and open the compartment C Insert the batteries Insert the batteries with their negative pole pointing at the resort and then gently press the battery into position until it is fully contained in the compartment Note When inserting please observe the correct polarity 10 23 02 2011 TireMoni manual v2 09 TireMoni TM 100 Tyre pressure monitoring system Tyre pressure above upper warning threshold lf the tyre pressure rises above the set upper warning threshold default setting 5 2 bars the display unit beeps ten times and switches on the backlight during three seconds The pressure value and HiP appear alternately This is represented in the figure to follow The pressure of the wheel rear left is too high In this example Rear Left R L H the pressure continues to rise the display unit gives
27. teries please observe the correct polarity Do not confuse the sensors sensor caps As soon as the batteries are becoming dead the battery condition gets displayed 12 23 02 2011 TireMoni manual v2 09 TireMoni TM 100 Tyre pressure monitoring system System operation 1 Initialisation During the initialisation phase the display unit first establishes the contact to the sensors and then displays information after starting up 2 Main screen After starting up the system displays the main screen Most of the time your system will stay in this display mode and show the most recent values for tyre pressure and temperature A beep tells the driver that the system is in operation Main screen Tiremoni manual v2 09 23 02 2011 25 TireMoni TM 100 Tyre pressure monitoring system 3 Advanced settings e Resetting to factory settings At times it is necessary to reset the device to factory settings This function allows setting all warning thresholds to default settings Before switching on the display please press the temperature button and switch it on while keeping the button pressed The reset is acknowledged by the system through two beeps e Learning mode If one of the sensors in the system needs to be replaced with a replacement sensor this function is required Each original sensor has its own ID number and no setting is required at this point However if the original sensor is lost or broken it
Download Pdf Manuals
Related Search