User Guide - Asus
Contents
1. Mve a OT Bit e Brightness The adjusting range is from 0 to 100 The 4 4 button is also a hot key to activate this function e Contrast The adjusting range is from O to 100 e Saturation The adjusting range is from O to 100 e Hue Shift the image color between green and purple e Color Temp Contain four color modes 9300K 6500K 5500K and 5000K ff The DDC CI tool installed at your PC will display User 1 instead of the 5500K color temperature you selected for this monitor e Gamma Set the color mode to 2 2 or 1 8 e Advanced Setting Adjust the gain levels for R G B e Adjust the black level offset values for R G B e Color Reset Current mode color reset Reset the color settings of current color mode to the factory default value e All modes color reset Reset the color settings of all color modes to the factory default value 3 4 Chapter 3 General Instruction 3 Image You can adjust the image Sharpness Trace Free Aspect Control ASCR Position VGA only and Focus VGA only from this main function 8 Splendid Sharpness 50 gt amp Color Trace Free 60 gt CD Sound Input Select Position gt X System Setup Focus gt AUTO Adjust gt A A w Move Menu s Exit e Sharpness Adjust the picture sharpness The adjusting range is from 0 to 100 e Trace Free Speed up the response time by Over Drive technology The adjusting range is from lower 02. COMMITMENT BY ASUS ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Notices Federal Communications Commission Statement This device complies with Part 15 ofthe FCC Rules Operation is subject to the following two conditions This device may not cause harmful interference and This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with manufacturer s instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user
3. components when trying to complete a task IMPORTANT Information that you MUST follow to complete a task Z NOTE Tips and additional information to aid in completing a task vi Where to find more information Refer to the following sources for additional information and for product and software updates 1 ASUS websites The ASUS websites worldwide provide updated information on ASUS hardware and software products Refer to http www asus com 2 Optional documentation Your product package may include optional documentation that may have been added by your dealer These documents are not part of the standard package 1 1 Welcome Thank you for purchasing the ASUS PB278Q Series LCD monitor The latest widescreen LCD monitor from ASUS provides a crisper broader and brighter display plus a host of features that enhance your viewing experience With these features you can enjoy the convenience and delightful visual experience that the PB278Q Series brings you 1 2 Package contents Check your PB278Q Series LCD monitor package for the following items LCD monitor Power Cord VGA Cable DVI Cable Dual link DisplayPort Cable HDMI Cable Audio Cable Quick Start Guide Warranty Card ROR SO A If any of the above items is damaged or missing contact your retailer A immediately ASUS LCD Monitor PB278Q Series 1 1 1 2 1 3 Assembling the monitor To assemble the monitor 1 Place the display flat
4. on a cloth on the table assemble the base according to the drawing and use a coin to turn the screw tight 2 Put the cable clip inset the hole of stand and adjust the monitor to the angle that is most comfortable for you Chapter 1 Product Introduction 1 4 Monitor introduction 1 4 1 Front ofthe LCD monitor 1 Power Button Power Indicator Press this button to turn the monitor on off 8 The color definition of the power indicator is shown below Status Description Blue ON Amber Standby mode OFF OFF 2 Input Select Button e Press this button to select input source 3 X A Button Press this button to increase values or to move your selection right up e Brightness hotkey 4 MENU Button Press this button to turn on the OSD menu or to enact the selected OSD menu item ASUS LCD Monitor PB278Q Series 1 3 1 4 e Press this button to exit the hotkey OSD menu 4 V Button Press this button to decrease values or to move your selection left down e Volume hotkey QuickFit button Press this button to activate the QuickFit function designed for alignment The QuickFit function contains 9 pages of common grid patterns paper sizes and photo sizes Please refer to 1 3 3 QuickFit Function B B Button Press this button to select a desired preset mode Press
5. 6 25kHz 1920x1080P 59 94 60Hz 67 433 67 5kHz The modes not listed in the above tables may not be supported For optimal resolution we recommend that you choose a mode listed in the above tables ASUS LCD Monitor PB278Q Series 3 11
6. Scenery Mode gt Sound Theater Mode gt Input Select User Mode gt x System Setup gt Move Ezg Menu Ls Exit Standard Mode This is the best choice for document editing with SPLENDID Video Intelligence sRGB Mode Compatible with sRGB color space SRGB mode is the best choice for document editing Color White Point Primaries Space Xw Yw Xr Yr Xi Y Xb Yb sRGB 0 3127 0 329 0 64 0 33 0 3 0 6 0 15 0 06 ool 00 ai 1 03 of 05 08 or OB z Scenery Mode This is the best choice for scenery photo displaying with SPLENDID Video Intelligence Theater Mode This is the best choice for movie watching with SPLENDID Video Intelligence Chapter 3 General Instruction User Mode More items are adjustable in the Color menu Function Standard sRGB Scenery Theater User Mode Mode Mode Mode Mode Brightness Yes Yes Yes Yes Yes Contrast Yes No Yes Yes Yes Saturation No No Yes Yes Yes Hue No No No No Yes Color Temperature Yes No Yes Yes Yes Gamma Yes No No No Yes Advanced Gain No No No No Yes Setting Offset No No No No Yes ASUS LCD Monitor PB278Q Series 2 Color Select the image color you like from this function ASUS PB278 8 Splendid Brightness 100 gt Contrast 80 gt Image Sound Input Select Color Temp 6500k gt X System Setup Gamma 22 gt Color Reset gt
7. al La PB278Q Series LCD Monitor User Guide Table of contents Notices Safety NfOrMmatiOn asecccacccceciacseds stecccecteccesacstesccasseactscrseecaneseesnetacas crucescesvaraeas iv Care amp Clam iMG iiiececccccsecensictexcesteccterccdeerer ne enternarceteat erento ntnenataiteewiees v 1 1 Welcome iscccistscarssscsscasssstecssceseepsesissensarsdscassteronseasapsonersvasscntsansenioa 1 1 1 2 Package contents nunnsensnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnannnnnnnanennn 1 1 1 3 Assembling the monitor uusnssnenennsnnnonnnnnnnnnnnnnnnnnnnnnnnnannnnnnnnannn 1 2 1 4 Monitor introduction ursseensnrnnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnnnnnnnnannnn 1 3 1 4 1 Front of the LCD monitor ennnnennnnnnenenn 1 3 1 4 2 Rear of the LCD monitor nenneenennnnnnnnnn 1 5 1 4 3 QUICKFit FUNCTION esssesnsennsnsennnnnnnnnnnnnnnnnnnnnnnnns 1 6 2 1 Detaching the arm stand for VESA wall mo Nt 20 snsnnannnnnnennnnnanuneneteen 2 2 Adjusting the monitor usesesnssnenennnnnnnnnnnnnnennnnsnnnnnnnnnnnnnnnnnnann 2 3 Connecting the cables 3 1 OSD On Screen Display menu 3 1 1 Howtorreconfigure ana wal anes 3 1 2 OSD Function Introduction 3 2 3 2 Specifications sce scccscsais seed scan acccseay seceseassctsatdecsecgeepien evesasectccsastces 3 8 3 3 Troubleshooting FAQ scsssssese senses esses 3 9 3 4 Supported Timing List sssssssssseseseessteesserstesseesneer
8. ault mode ASUS LCD Monitor PB278Q Series 3 7 3 2 Specifications Model PB278Q 1920x1080 VGA 2560 x 1440 DVI HDMI Max Resolution DP Brightness Typ Intrinsic Contrast Ratio Typ ET O Display Colors Response Time Satellite Speaker 3W x 2 stereo Sound from HDMI HDMI input D Sub input Yes Yes Yes Audio Line in Power ON Consumption lt 60W Tit Swivel angle Pivot angle direction 90 clockwise Height Adjustment mm VESA Wall Mounting Phys Dimension WxHxD Box Dimension WxHxD Net Weight Esti Gross Weight Esti Voltage Rating AC 100 240V Built in Specifications are subject to change without notice Chapter 3 General Instruction 3 3 Troubleshooting FAQ Problem Power LED is not ON The power LED lights amber and there is no screen image Screen image is too light or dark Screen image is not centered or sized properly Screen image bounces or a wave pattern is present in the image Screen image has color defects white does not look white Screen image is blurry or fuzzy No sound or sound is low HDMI cannot support WQHD ASUS LCD Monitor PB278Q Series Possible Solution Press the button to check if the monitor is in the ON mode Check if the power cord is properly connected to the monitor and the power outlet Check if the monitor and the computer are in the ON mode Make sure the signal cable is properly connected the monitor a
9. d feel Alignment Grid 2 Paper size QuickFit provides numerous commonly used standard paper sizes for users to view their documents in real size on the screen Pott emer Chapter 1 Product Introduction 3 Photo size The various real photo sizes displayed in the QuickFit function provides photographers and other users to accurately view and edit their photos in real size on the screen Photo 4x6 3x5 2x2 Photo 8x10 5x7 ASUS LCD Monitor PB278Q Series 1 7 2 1 Detaching the arm stand for VESA wall mount The detachable stand of this monitor is specially designed for VESA wall mount To detach the arm stand 1 Disconnect power and signal cables Carefully put the front of the monitor face down on a clean table 2 Use a screwdriver to remove the four screws on the arm Figure 1 and then detach the arm stand from the monitor Figure 2 prevent damage to the monitor Hold the stand of the monitor while removing the screws AN We recommend that you cover the table surface with soft cloth to e Figure 1 Figure 2 ff The VESA wall mount kit 100 x 100 mm is purchased separately Use only the UL Listed Wall Mount Bracket with minimum weight load 28 8 kg Screw size 4x 10 mm 2 1 Chapter 2 Setup 2 2 Adjusting the monitor For optimal viewing we recommend that you look at the full face of the monitor then adjust the monitor to the angle that is most comfortable f
10. e e Source Adjust audio source to Line In or HDMI only available for HDMI input Adjust audio source to Line In or DisplayPort only available for DisplayPort input 5 Input Select Select the input source from VGA DVI HDMI or DisplayPort ASUS PB278 E splendid VGA gt amp Color DVI gt Image HDMI gt Sound DisplayPort gt CO 8 System Setup gt Move peg Menu Ls Exit 3 6 Chapter 3 General Instruction 6 System Setup Adjusts the system configuration splendid amp Color Image Sound Input Select Splendid Demo Mode OSD Setup Information Language Power Indicator All Reset Menu LS Exit OFF gt gt gt English gt ON gt gt e Splendid Demo Mode Split the screen into two for Splendid modes comparison Scenery mode Theater mode only e OSD Setup Adjust the horizontal position H Position vertical position V Position OSD Timeout DDC CI and Transparency of the OSD screen e Information Display the monitor information e Language Select OSD language The selections are English French German Spanish Italian Dutch Russian Traditional Chinese Simplified Chinese Japanese Persian Thai Indonesian Poland Turkey Portugal Czech Croatia Hungary Romania Korean e Power Indicator Turn the power LED indicator on off e All Reset Set to Yes to revert all settings to the factory def
11. e cables and power cord Follow the correct lifting techniques when positioning the monitor When lifting or carrying the monitor grasp the edges of the monitor Do not lift the display by the stand or the cord Cleaning Turn your monitor off and unplug the power cord Clean the monitor surface with a lint free non abrasive cloth Stubborn stains may be removed with a cloth dampened with mild cleaner Avoid using a cleaner containing alcohol or acetone Use a cleaner intended for use with the LED Never spray cleaner directly on the screen as it may drip inside the monitor and cause an electric shock The following symptoms are normal with the monitor The screen may flicker during the initial use due to the nature of the fluorescent light Turn off the Power Switch and turn it on again to make sure that the flicker disappears You may find slightly uneven brightness on the screen depending on the desktop pattern you use When the same image is displayed for hours an afterimage of the previous screen may remain after switching the image The screen will recover slowly or you can turn off the Power Switch for hours When the screen becomes black or flashes or cannot work anymore contact your dealer or service center to fix it Do not repair the screen by yourself Conventions used in this guide A WARNING Information to prevent injury to yourself when trying to complete a task N CAUTION Information to prevent damage to the
12. io Port e To use the earphone Connect the end with plug type to the monitor s earphone jack when an HDMI or DisplayPort signal is fed ff When these cables are connected you can choose the desired signal from the Input Select item in the OSD menu Chapter 2 Setup 3 1 OSD On Screen Display menu 3 1 1 How to reconfigure ASUS PB278 Standard Mode gt amp Color sRGB Mode gt Pr Image Scenery Mode gt Sound Theater Mode gt Input Select User Mode gt x System Setup gt a 7 v Move E Menu B Exit 1 Press the MENU button to activate the OSD menu 2 Press W and t A to navigate through the functions Highlight and activate the desired function by pressing the MENU button If the function selected has a sub menu press W and Xt amp again to navigate through the sub menu functions Highlight and activate the desired sub menu function by pressing the MENU button 3 Press Wand 3 A to change the settings of the selected function 4 To exit the OSD menu press the amp B button Repeat step 2 and step 3 to adjust any other function ASUS LCD Monitor PB278Q Series 3 1 3 1 2 OSD Function Introduction 1 3 2 Splendid This function contains five sub functions that you can select for your preference Each mode has the Reset selection allowing you to maintain your setting or return to the preset mode Standard Mode gt amp Color sRGB Mode gt Image
13. is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help ca As an Energy Star Partner our company has determined that this product meets the Energy Star guidelines for Ag energy efficiency ENERGY STAR Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications This class B digital apparatus complies with Canadian ICES 003 Safety information Before setting up the monitor carefully read all the documentation that came with the package To prevent fire or shock hazard never expose the monitor to rain or moisture Never try to open the monitor cabinet The dangerous high voltages inside the monitor may result in serious physical injury If the power supply is broken do not try to fix it by yourself Contact a qualified service technician or your retailer Before using the product make sure all cables are correctly connected and the power cables are not damaged If you detect any damage contact your dealer immedia
14. mary Timing Resolution Refresh Rate Horizontal Frequency 1152x864 75Hz 67 5kHz 1280x1024 1440x900 1440x900 1680x1050 1920x1080 IBM Modes Factory Preset Timing D SUB DVI D HDMI inputs Resolution Refresh Rate Horizontal Frequency MAC Modes Factory Preset Timing Resolution 640x480 832x624 Resolution 848x480 1280x720 RB 1280x720 1280x720 1280x768 RB 1280x800 RB Refresh Rate Horizontal Frequency 35kHz 49 725kHz VESA Modes User Available Timing Refresh Rate Horizontal Frequency Chapter 3 General Instruction 1280x800 60Hz 49 702kHz 1280x800 75Hz 62 795kHz 1366x768 60Hz 47 712kHz 1440x900 RB 55 469kHz 1440x900 70 635kHz 1680x1050 RB 64 674kHz 1920x1080 66 587kHz WQHD Mode DVI dual link HDMI and DP only 2560x1440 88 787kHz While the PB278Q supports up to 2560 x 1440 WQHD resolutions including DVI dual link HDMI and DisplayPort some graphics cards only support up to 1920 x 1200 resolution content transmission via HDMI Please check with your local distributor or retailer on the hardware limitations of your laptop or desktop SD HD Timings HDMI input only HDMI 1 3 CEA 861B nn SD HD Supported Primary Resolution Refresh Rate Horizontal Frequency 1920x1080i 50Hz 28 125kHz HDMI 1 3 CEA 861B Sroa SD HD Supported Optional Resolution Refresh Rate Horizontal Frequency 1440x480P 59 94 60Hz 31 469 31 5kHz 1440x576P 31 25kHz 1920x1080P 5
15. nd the computer Inspect the signal cable and make sure none of the pins are bent Connect the computer with another available monitor to check if the computer is properly working Adjust the Contrast and Brightness settings via OSD Press the B 6 button for two seconds to automatically adjust the image Adjust the H Position or V Position settings via OSD Make sure the signal cable is properly connected to the monitor and the computer Move electrical devices that may cause electrical interference Inspect the signal cable and make sure that none of the pins are bent Perform Reset via OSD Adjust the R G B color settings or select the Color Temperature via OSD Press the amp button for two seconds to automatically adjust the image for VGA mode only Adjust the Phase and Clock settings via OSD Ensure that the audio cable is properly connected to the monitor and the computer Adjust the volume settings of both your monitor and computer Ensure that the computer sound card driver is properly installed and activated While the PB278Q supports up to 2560 x 1440 WQHD resolutions including DVI dual link HDMI and DisplayPort some graphics cards only support up to 1920 x 1200 resolution content transmission via HDMI Please check with your local distributor or retailer on the hardware limitations of your laptop or desktop 3 10 3 4 Supported Timing List PC Supported Pri
16. or you Hold the stand to prevent the monitor from falling when you change its angle You can adjust the monitor s angle from 20 to 5 and it allows 60 swivel adjustment from either left or right You can also adjust the monitor s height within 12cm 5 20 60 Ey 60 12cm Pivoting the monitor 1 Lift the monitor to the highest position 2 Tilt the monitor to its maximum angle 3 Pivot the monitor clockwise to the angle you need Sr y4 It is normal that the monitor slightly shakes while you adjust the viewing angle ASUS LCD Monitor PB278Q Series 2 2 2 3 Connecting the cables Connect the cables as the following instructions e To connect the power cord Connect one end of the power cord securely to the monitor s AC input port the other end to a power outlet e To connect the VGA HDMI DVI DisplayPort cable a Plug one end of the VGA HDMI DVI DisplayPort cable to the monitor s VGA HDMI DVI DisplayPort jack b Connect the other end of the VGA HDMI DVI DisplayPort cable to your computer s VGA HDMI DVI DisplayPort jack c Tighten the two screws to secure the VGA DVI connector e To connect the audio cable Plug one end of the audio cable to the monitor s Audio Line in Port Connect the other end of the audio cable to your computer s aud
17. steeaneeeaeees 3 10 Copyright 2012 ASUSTeK COMPUTER INC All Rights Reserved No part of this manual including the products and software described in it may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form or by any means except documentation kept by the purchaser for backup purposes without the express written permission of ASUSTeK COMPUTER INC ASUS Product warranty or service will not be extended if 1 the product is repaired modified or altered unless such repair modification of alteration is authorized in writing by ASUS or 2 the serial number of the product is defaced or missing ASUS PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT SHALL ASUS ITS DIRECTORS OFFICERS EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING DAMAGES FOR LOSS OF PROFITS LOSS OF BUSINESS LOSS OF USE OR DATA INTERRUPTION OF BUSINESS AND THE LIKE EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE AND SHOULD NOT BE CONSTRUED AS A
18. tely Slots and openings on the back or top of the cabinet are provided for ventilation Do not block these slots Never place this product near or over a radiator or heat source unless proper ventilation is provided The monitor should be operated only from the type of power source indicated on the label If you are not sure of the type of power supply to your home consult your dealer or local power company Use the appropriate power plug which complies with your local power standard Do not overload power strips and extention cords Overloading can result in fire or electric shock Avoid dust humidity and temperature extremes Do not place the monitor in any area where it may become wet Place the monitor on a stable surface Unplug the unit during a lightning storm or if it will not be used for a long period of time This will protect the monitor from damage due to power surges Never push objects or spill liquid of any kind into the slots on the monitor cabinet To ensure satisfactory operation in case use at a PC then it should use the monitor only with computers which have appropriate configured receptacles marked between 100 240V AC If you encounter technical problems with the monitor contact a qualified service technician or your retailer The wall socket shall be installed near the equipment and shall be easily accessible Care amp Cleaning Before you lift or reposition your monitor it is better to disconnect th
19. this button to exit the OSD menu or to go back to the previous menu when the OSD menu is active Press this button for 2 4 seconds to automatically adjust the image to its optimized position clock and phase for VGA mode only Chapter 1 Product Introduction 1 4 2 Rear of the LCD monitor SUS Rear connectors 1 Kensington lock slot 2 AC IN port This port connects the power cord 3 DisplayPort This port is for connection with a DisplayPort compatible device 4 VGA port This 15 pin port is for PC VGA connection DVI port This 24 pin port is for PC Personal Computer DVI D digital signal connection 6 HDMI port This port is for connection with an HDMI compatible device V While the PB278Q supports up to 2560 x 1440 WQHD resolutions including DVI dual link HDMI and DisplayPort some graphics cards only support up to 1920 x 1200 resolution content transmission via HDMI Please check with your local distributor or retailer on the hardware limitations of your laptop or desktop 7 Audio Line in Port 8 Earphone jack ASUS LCD Monitor PB278Q Series 1 5 1 6 1 4 3 QuickFit Function The QuickFit function contains three patterns 1 Grid 2 Paper size 3 Photo size 1 Grid patterns The grid patterns facilitate designers and users to organize content and layout on a page and achieve a consistent look an
20. to faster 100 e Aspect Control Adjust the aspect ratio to Full 4 3 1 1 or Over Scan The 4 3 ratio is only for 4 3 or 5 4 image source The Over Scan ratio is only available for HDMI input e ASCR Turn on or off the ASCR ASUS Smart Contrast Ratio function Only available at Scenery Mode and Theater Mode e Position Adjust the horizontal position H Position and the vertical position V Position of the image The adjusting range is from 0 to 100 only available for VGA input e Focus Reduce Horizontal line noise and Vertical line noise of the image by adjusting Phase and Clock separately The adjusting range is from 0 to 100 only available for VGA input e AUTO Adjust Automatically adjust the image to its optimized position clock and phase Only available for VGA input V Phase adjusts the phase of the pixel clock signal With a wrong phase adjustment the screen shows horizontal disturbances Clock pixel frequency controls the number of pixels scanned by one horizontal sweep If the frequency is not correct the screen shows vertical stripes and the image is not proportional ASUS LCD Monitor PB278Q Series 3 5 4 Sound Adjust the sound settings to your preference ASUS PB278 8 Splendid Volume 50 gt amp Color Mute OFF gt Pf Image Input Select x System Setup e Volume Adjust the output volume level e Mute Mute the output volum
Download Pdf Manuals
Related Search