슬라이드 1 - Speechi
Contents
1. UD Cum e User Manual OPS Computer Open Pluggable Specification Computer 5 echi solutions Overview Icon Descriptions The icons are used in the manual to serve as an indication of interest topics or important messages Below is a description of these icons NOTE This mark indicates that there is a note of interest and is something that you should pay special attention on while using the product WARNING This mark indicates that there is a caution or warning and it is something that could damage your property or product Copyright and Trademarks This document is copyrighted 2014 All rights are reserved The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of the original manufacturer Information provided in this manual is intended to be accurate and reliable However the original manufacturer assumes no responsibility for its use nor for any infringements upon the rights of third parties that may result from such use Version 1 0 Acknowledgement Intel Pentium and Celeron are registered trademarks of Intel Corp Microsoft Windows and MS DOS are registered trademarks of Microsoft Corp All other product names or trademarks are pro2. 18 19 C z3 CA 0 c Version 1 0 Line out Jack Line 1 1 LINE OUT 2 Me 4 IEARPHONEDET 2 2 6 1 GND O Microphone Jack MIC1 PN Sina 4 7 MICDET 6 GND High Definition Multimedia Interface HDMI1 19 177 135 133 8 9 7 5 3 1 18 12 10 8 6 4 2 PINNO Signal PINNO Signal 10 Version 1 0 Chapter 3 Gigabit Ethernet LAN1 Mini PCI Express with SIM Card Reader MPCIE1 PinNo Signal PINNO jJFastEthemet X Gigabit Ethernet IN NO ignal Signal __ S 1 5 TX MD0 2 Jn R MO Un S 6 B 10 T amp C 2 2 2 O E 9 7 10 50 10 10 10 100 1 dind AT O D ie OQ DISABLE Dual Stack USB 3 0 Type A Connector USB1 to 7 um un UJ T a OQ C a OQ ED WWAN s ED_WLAN ED WPAN EID Un gt 4 DB PD o9 G9 G9 IN ININ IN N O 00 60 OD IN O OV CO to x 3 3V PIN NO Signal NO 1 Juss vec ho 058 PIN No 2 jUsB iD 11 USB2 D 1 2 Normal Default Clear CMOS o USB1 TX 18 USB2 TX 11 Chapter 4 Chapter 4 Hardware Setup Preparing the Hardware Installation To access s
3. Chapter 3 Chapter 3 Board connector Connectors and Jumpers List The tables below list the function of each of the board connectors by labels shown in the above section The next section in this chapter gives pin definitions ub rnn Definition Ref Page Chapter 3 OPS Connector OPS1 Signal DDP 3P 20 20 20 ta lt lt lt DDP 2N DDP 2P MJ J AL IN IN O Un Un Cn Un JO Un Ae gt 4 OV Ur 4 Jw N N W XO OV 0 Ww N2 WIN C DDP GND 55 zo zs 50 x lt lt lt Addis 2 0 DDP ON YS FAN EN ART RX ART TX tda SSRX tda SSRX4 tda SSTX tda_SSTX SB_PN2 SB_PP2 SB_PN1 SB_PP1 SB_PNO SB_PPO AZ_LINEOUT_L 70 AZ_LINEOUT_R B DET S_ON WR_STATUS ND 2 DDP AUXP Win 2 MDS CLKN MDS CLKP Win Z MDSON MDSOP Cic Z MDS1N MDS1P GEIG MDS2N MDS2P CIC C l E 1 1 G G gJ 5 12 2 gt Z 21010 101210 gt 21010 gjo o o ojo S UJ zeel 2 o gt A 2 DATA TMDS _ rm MDS HPLUG us DC IN DC IN 79 79 DC IN DC IN DC IN DC IN DC IN C amp G G G G 212121212 O PIN E 4 E E 10 16
4. ING uie e E 8 Chapter 3 Board Connector 9 Connectors Jumpers Dst oa Gaeta tele e abu debis och 9 ee 10 Chapter 4 Hardware Setup 12 Preparing the Hardware Installation 12 SEN MENO 12 3G Wireless Module Installation sess 13 3G SIM Era Installaubblsseaascequ 13 Metalno The bate DISK so 13 Appendix A Terms and Conditions 14 Warant y POI eh 14 RMA 14 Version 1 0 Version 1 0 Chapter 1 Chapter 1 Introduction System Specification Thank you for choosing the AOPS 7080 The CPU Intel Core 15 4400 Processor Cache AOPS 7080 is an Open Pluggable Specification OPS for IWB and digital signage application BIOS AMI SPI BIOS The AOPS 7080 addresses IWB and digital signage market fragmentation and simplify device installation usage maintenance and upgrades System Memory DDR3L 1333 4GB 2GB x 2 System chipset Intel QM87 Express Chipset This OPS provides a rich I O capabilities via high I O bandwidth interfaces such as PCI Express 2 0 Storage 2 5 SDD 128GB Serial ATA 3 0 and Hi Speed USB 3 0 connectivity 2x USB 3 0 Type A in front panel USB 3x USB 2 0 and 1x USB 3 0 through JAE TX25 80 pin conn
5. allation Optional 1 Take out the Mini PCIe and SIM card compartment s cover by unscrewing the screws on the cover Align the wireless module s cutout with the Mini PCIe slot notch 3 Insert the wireless module into the connector diagonally 4 Push the other end of the wireless module and secure it in place with the screws 5 Install the Antenna to the module NO 3G SIM Card Installation Optional 1 Take out the Mini PCIe and SIM compartment s cover by unscrewing the screws on the cover 2 Unlock the SIM card tray by sliding it outward and open it Place the SIM card in the tray Make sure the ICs is in contact with the socket The angled corner of the SIM ensures that the card fits only the correct way in the tray 4 Close and lock the tray You should feel a click when the SIM card is locked securely in the socket UJ 4 Version 1 0 Installing the Hard Disk The system can accommodate one Serial ATA 2 5 disk Follow these steps to install a hard disk into the AOPS 7080 1 Take out the hard disk tray from the system Place hard disk on the hard disk tray and align the holes of the hard disk with the mounting holes on the tray Fix the hard disk on the hard disk tray by using 2 mounting screws 4 Push the hard disk into the hard disk slot and NO UJ secure it with a screw Drive Connector Power Connector Note The system only accommodates 2 5 SSD It support
6. ector Other I O capabilities include an HDMI port a MIC In and Line Out as well as an Intel 1210 Mini PCIe 1x mini PClexpress socket for mini card module Gigabit Ethernet Display Chipset Intel integrated HD 4600 Display HDMI Display port and TMDS through JAE TX25 Supported 80 pin connector Audio Interface Chipset Realtek ALC886 Mic in Line out Audio L R through JAE TX25 80 pin connector LAN Chip Intel amp i210 Gigabit Ethernet Ethernet 1x10 100 1000 Base Tx Gigabit Ethernet Warning Mechanical amp Environmental While using the OPS do not mle DC 12V 5A disconnect the power source Requirement It will be Cause fatal failure 5 C to 45 C 32 140 Storage 20 C to 75 C 4 158 Temperature 119mm D x 200mm W x 30mm H SS ONO Vise 20807 Certification CE FCC KCC Version 1 0 Chapter 1 Package Contents If any items are missing contact your dealer Your package contains the following items e AOPS 7080 OPS System installed Set e Drivers and User s Manual CD e Adaptor DC12V Version 1 0 Chapter 2 Chapter 2 System Components System Drawing Mechanical dimensions of the AOPS 7080 Unit mm n 2589 FERREA UE ODDO Chapter 2 Front Connectors Component F1 Hard Disk Slot F2 Antenna Hole Gigabit Ethernet LAN port The LAN port is pr
7. important occurred in normal Lipset nge g pu pair impo The price use performance u failure occurs of When the exchange is not possible rig When Defective goods occurrence Charged repair When the re fair is Repair for the same Defective but when Components within of fail 4ti Compo recurrence ilures 4 time Product exchange Duration of use based on the the retention period when the repair is not possible or The purchase price Refunds if consumer requesting repairs ces business lost it e ee ey MEINT incurred during installation Product exchange Due to negligence men epar is Charged repair Charged repair on the part of Possible After collecting the consumers ng performance failure When the refair is Performance functional failure or damage is amount paid to Our standard Subject to determined of functional possible not a defect in repair the exchange a separate Consumer 2 05 E spontaneous bed us refair is not d of the consumer if Can not be repaired Can not be repaired ecomposition e With regard to the product of the three defects in the compensation is not subject S e e C h www speechi net P 12 rue de weppes 59800 Lille France info speechi net
8. ome components and perform certain service procedures you must perform the following procedures first WARNING To reduce the risk of personal injury electric shock or damage to the equipment remove the power cord to remove power from the server Portions of the power supply and some internal circuitry remain active until power is removed 1 Unpowered the AOPS 7080 and make sure that the power source is removed 2 It is not required to remove the system s top cover for installing most parts of the system such as the memory 3G wireless module SIM card and the hard disk Version 1 0 Installing the System Memory The motherboard supports DDR3L memory that features data transfer rates of 1333 MHz to meet the higher bandwidth requirements of the latest operating system and Internet applications It comes with one Double Data Rate 3 Low Voltage DDR3L Small Outline Dual Inline Memory Module SO DIMM socket im 2 Put the device upside down Take off the cover of the memory compartment by unscrewing two screws from its cover Align the memory module s key with the SO DIMM socket s key Install the SO DIMM Install the cover back to the system Note 1 SO DIMMs installed should meet the required speed which is DDR3L 1333 MHz Do not install SO DIMM supporting different speeds 2 The motherboards can support up to 16 GB memory capacity in maximum 12 Chapter 4 3G and Wireless Module Inst
9. ovided by Intel i210 Ethernet LAN1 on page 11 LINK ACT F4 USB 3 0 type A ports R5 HDMI Port F7 Reset Button F8 Mic in Port Line out F9 HDD Green and Power LED Green External 2 5 hard drive bay for easy access and replacement of the data storage It sup ports SATA 3 0 specification Reserved hole for 3G Wi Fi module antenna controller which supports10 100 1000Mbps connection speeds and PXE Preboot eXecution Environment The LAN port LED indicator is described below LINK ACT Amber On Flashing The port is linking and active in data transmission Off The port is not linking SPEED Green Yellow Yellow The connection speed is 1000Mbps Green The connection speed is 100Mbps The connection speed is 10Mbps Two USB 3 0 type A ports USB1 on page if n HDMI port single link which is provided HDMI1 on page 10 by Intel integrated HD 4600 ATX power on button with LEDs stand by mode in red power on mode in green A hardware reset button Connect audio devices to these port MIC1 LINE1 on page 10 HDD Blinking data access activities Off no data access activities Power On The computer is on Off The computer is off Version 1 0 Version 1 0 Chapter 2 Rear Connectors Component Description Pin Definition Reference R1 TX 25 80 pin connector This connects to the docking board LEK IOB2 OPS1 on page 10 Version 1 0 Connectors and Jumpers List
10. perties of their respective owners Compliances and Certification CE Certification This product has passed the CE test for environmental specifications Test conditions for passing included the equipment being operated within an industrial enclosure In order to protect the product from being damaged by ESD Electrostatic Discharge and EMI leakage we strongly recommend the use of CE compliant industrial enclosure products FCC Class A Certification This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Contents Chapter 1 Introduction 4 System SSCA T ON 4 Package 5 Chapter 2 System Components 6 E E E T 6 FONU COM MCCIONS cT a Rear COM
11. s SATA 3 0 specification lt 13 Version 1 0 Appendix A Terms and Conditions Warranty Policy 1 All products are under warranty against defects in materials and workmanship for a period of one year from the date of purchase 1 Compensation standard of our products in accordance with the Ministry of Finance Notice legitimate consumer damage will be compensated Product Warranty Product Model Purchase a day ear month da Customer Name Phone Address Mutual agency Phone Address e When requesting repairs and the year of purchase date must be presented above Enough to receive service so please keep it e Major parts of the retention period is 2 years 1 Warranty for this product to ensure the information contained in the warranty benefits 2 The warranty period calculated from the date of purchase dated so please come Date of purchase If this should not check 6 months from date of manufacture from the date of the warranty period shall be added to 3 Not household products also operating activities unusual environments etc or industrial products If the warranty period of 6 months will apply Key parts 4 This warranty will not be reissued Compensation for consumers guide Product exchange when within 10 days of purchase repair important requiring or The purchase price Refunds when within 1 month of purchase repair important requiring When exchange goods within 1 month of purchase repair
Download Pdf Manuals
Related Search