Table of Contents І. Summary 1. Basic function of the alarm host
Contents
1. control mobile phone or telephone numbers to call the telephone which connect to the alarm host when it has reached the setting ring times alarm host will automatically connect Input the password when there is a voice prompt ask to input password and end up with key There is voice prompt when the password is correct Press 1 for arm Press 2 for disarm Press 5 for listen in press 6 for unlock please press for dismiss the alarm Hang up to quit If password is wrong voice prompt with Password is not correct please input again When the Password is correct Enter 1 for arm the host enter 2 to disarm the host Attention In HOME ARM state the detector will alarm when choosed the HOME type to code In AWAY type when code will not alarm In AWAY ARM no matter in HOME or AWAY type when code the detectors will alarm 5 Alarm trigger action Method one In ARM state alarm host will trigger alarm by all kind of detectors Method two In any state belong to emergency alarm detector type will trigger to alarm such as smoke detector gas detector panic button and so on Method three In any state Press the emergency button on the wireless remote controller will trigger to alarm already registered with the alarm host Method four In any state the lock which work with the alarm host has forced to open will alarm Display screen will show as follow i wa 38 13805243195 G2. mode when registered the detectors will alarm II Setting and usage of the alarm host 1 Alarm host basic setting Alarm host must do some necessary settings before use then the system can work in a normal working condition When start to set In lock state must input the password to unlock the keyboard the initial password is 1234 like the following figure left one is standby mode there is a lock icon show in the upper left corner the right one is unlock mode tay 24 45 32 244 32 1G 28 18 28 Keyboard will automatically locked when there is no any operations on the keyboard for 15 seconds 1 In unlock state When press the PROGRAM key voice prompt with System is in registration state can input instruction for corresponding settings on the keyboard When one instruction has completed The cursor in the middle of a line on the left will blink in the LCD display No need to quit the program state can move to next instruction setting If do not want to save during setting or setting has completed Directly press BACK key to quit the setting state Voice prompt with System is quitting registration state when quit Example when setting telephone number LCD display as follow upper left corner is serial Numbers telephone number is in the middle BEISA HF eh Detailed instructions and setting as follows Attention All instructions must operate in programming stat
3. setting 9 Wireless siren learning code and usage 1 Learning code between the wireless siren and alarm host First the host in the program state please input 19 instruction to launch wireless signal Plug in the wireless siren power supply One beep sound means the wireless siren is ready to work then plug off the power supply then plug in again at this time siren with no any sound plug off the power supply then plug in again then the wireless siren will make beep beep beep prompt sound this mean siren register complete Simple steps as follows Power on beep power off then power on no beep power off then power on beep beep beep code successfully Every step time interval is 1 2 seconds 2 Wireless siren usage When the siren has registered complete power on the siren will make beep beep two sound when arm or disarm the alarm host when alarm host alarming the siren will make a continuous sound Thanks for reading our manual any questions please contact our after sales service
4. state The zone on the LCD display will show 01 Can change the zone by press the number on the panel Press HOME ARM or AWAY ARM to choose alarm type then trigger the detector to alarm The alarm host will voice prompt Registered complete after receive the signal from the detectors or remote controllers Then if press the BACK key or CODE key means exit the code state If need code other detectors no need to exit according to the above method directly input the zone number then choose the alarm type to learning code until the code is completed then press the BACK key or CODE key to exit the code state Add detectors code If need add detectors or remote controllers and do not want to delete the exiting detectors or remote controllers code can add code by learning code as follows First click the CODE key then press it again for 2 3 seconds the alarm host will voice prompt System is in registration state Then use the first time code way to choose zone and alarm type to learning code Clear the code System need initialization to clear the code Attention In HOME ARM state the detector will alarm when choosed the HOME type to code In AWAY type when code will not alarm In AWAY ARM o matter in HOME or AWAY type when code the detectors will alarm 3 The learning code of intelligent lock and alarm host In the premise of work with intelligent lock T
5. the intelligent lock and alarm host together must insert the USB which belong to the door to register with the alarm host After the register has complete put the USB back to intelligent lock to use UNE IN LUNE OUT POWER PORT SIREN USBPORT SWITCH O c ON OFF CONNECT WITH TELEPHONE THE NETWORK EJ MODEM 9V300mA DC POWER WIRE SIREN 4 Wireless detectors device installation 1 Magnetic door window installation The principle of magnetic door detector is induction the distance between the magnetron and magnet when the gap of magnet and magnetron is increased to a certain distance the detector can induction it then launch the signal to alarm Fix it on the door or window can detect the open or close of the door or window Separately install the magnet and emitter on the door and doorframe use adhesive tape and screw to fixe it The door detector has low power voice prompt function belong to new generation detectors 2 Infrared detector installation Passive infrared detector using infrared wavelengths to sense the temperature change to make sure the human activities Detection range from 5 to 8 M detection angle is level 110 vertical 60 Fix the infrared on the wall 2 2 2 meters away from the ground adjust the angle face the area which need to detect Attention Infrared detector has installed appropriate or not directly affect the accuracy of the alarm Please inquiry the supply before install in o
6. Table of Contents I Summary 1 Basic function of the alarm 2 Main technical sp cificatioNa Tenenio ani 2 3 Alarm system basic config rationisgssnsni niii 3 4 Optional configuration 45 0750 urnsdnainniean i 3 II Structure and installation of the alarm host 1 Installation of the alarm 1 2 Telephone line and power cord CONMECHON soisissa 5 2 wireless detector installation ccccesccsccecececeeececereeeee 6 MI Setting and usage of the alarm host 1 The basic setting of the alarm host 7 2 Coding between main host and wireless GOLECLOR niiin 14 3 Coding between main host and intelligent LOCK tedaitamedesgaue nne 14 4 To arm the alarm host cccsccsscsseeeeeseceeceeeenee 14 5 Trigger to alarm sccacs cede atviensrinerteraaieiocans erase 15 6 Alarm center Opera thon iassciisss ses einai av shpcanieanneays 16 7 Remote control OPSralOnca Misswenstasalacaesa nied ised 17 Ov OY Stell LEBEL ain ea E 17 9 Setting and usage of the wireless I Summary Thank you for purchasing our alarm system in order to enable you to use this products correctly and quickly please read this manual carefully before to use Our alarm system belong to a new generation of intelligent alarm system has made a dramatic improvement on the basis of the previous alarm system according to the users complaints Contrast as follows 1 The battery of Original infrared detector can only use 6 12 mon
7. center number 3 groups of long range control numbers 2 groups of detector low battery prompt numbers 7 Can control the alarm host arm disarm listen in by calling the alarm host number 8 Has voice prompt function when alarming or operating from long distance 9 Alarm host has the priority to make alarm phone calls when the telephone is being using And telephone line fault detection function 10 Using the learning code to add wireless detector easy to register 11 Wireless detector has low power prompt function 12 Wire detector support open circuit alarm and short circuit alarm 13 Wire detector malfunction has prompt function 14 Alarm host has build in siren and wireless transmitter module optional also support external wire or wireless siren optional 15 Arm or disarm with alarm tone 16 Anti tamper function 17 Auto arm and disarm function 18 Build in battery Automatic switching when power off 19 Can query recently 20 PCS history 2 Technical Parameters 1 2 3 4 5 6 7 8 9 Power supply DC9V 300mAh Backup battery 7 2V 1 2V x6 Ni MH rechargeable battery Work current Daily duties 20mA alarm communication 300mA Build in siren Open the wireless siren Wireless frequency Receive 315MHz emission 433 MHz Wireless encoding ASK Wireless receive sensitivity 105dBm 12dB SINAD Wireless zone number 95 Wire zone number 4 alarm number
8. d the setting time the alarm host will automatically enter into disarm state gt Unlock test instruction Operation instruction 18 Alarm host will enter into unlock state after input this instruction Press BACK key to exit program state gt Wireless siren code instruction Operation instruction 19 The alarm host will launch the wireless alarm signal to register after input this instruction Press BACK key to exit program state gt Query History Operation instruction 04 After input this instruction can press or key to query latest 20 PCS system records As shown below 16 21 34 intrude 0u 28 This alarm content says Third times alarm Zone 35 Alarm type is intrude Alarm time is at 16 27 34 PM on December 28 In addition arm or disarm operations will also be recorded Arm records has no zone number and alarm type the home arm or away arm indicator lights will be on at the same time If away arm indicator lights on means away arm record Disarm record has no zone number and alarm type the home arm or away arm indicator light will not on at the same time 2 The learning code of wireless detector and remote controller In standby mode by pressing the top of the host coding key for learning code to wireless remote controller and wireless detectors 2 First time to code Press the CODE key for 2 3 seconds the alarm host will voice prompt System is in registration
9. dle of the LCD zone Press will delete then press PROGRAM to save Then press BACK key to quit If only need to change the number Then input a new number after delete or directly input the new number gt Setting system password Operation instruction O5 LCD will display original 4 digit password default 1234 after input the instruction Re enter 4 digit password Press the PROGRAM key to save after input has completed System will back to program state Input other instructions can carry out other settings gt Setting user ID Host ID or User ID Alarm host connect with alarm center When send alarm information to alarm center need identify the user code or host ID user ID Operation instruction O7 LCD will display 4 digit user code default 0001 after input the instruction Re enter 4 digit code press PROGRAM key for save after input has completed System will back to program state Input other instruction for carry out other setting gt Setting remote control answering ring times Operation instruction 08 In the middle of the LCD region will show original ring times after input the instruction Input a new number for ring times then press PROGRAM key for save System will back to program state Input other instructions for carry out other settings Attention Most of the telecom network operator support 8 times ring Please don t set the times more than network operator times De
10. e gt Setting alarm center number This number will automatically dial when there is an alarm to inform alarm center if the user didn t connect with the networking system platform please do not set this number otherwise will continuously to call this number affect the speed of user to dial the other numbers Operation instruction O1 The upper right number will flashing after input this instruction Input 1 or 2 input telephone number Press PROGRAM key to save after input has completed System will back to grogram state Input other instructions to carry out other settings Description 1 or 2 means the first alarm center number or the second alarm center number gt Setting user alarm number Alarm host will automatically dial this number to inform the user when there is an alarm Operation instruction 02 The upper right number will flashing after input this instruction input 1 2 or 3 then input telephone numbers Press PROGRAM key to save after input has completed System will back to program state Input other instructions to carry out other settings Description 1 2 or 3 means the first the second and the third telephone numbers gt Setting detector low battery prompt numbers In the case when the detectors have low battery alarm host will automatically dial the number to inform the user Operation instruction 024 The upper right number will flashing after i
11. fault is 6 times Because this host has recognized number to control So no need to worry about other incoming calls will automatically connected gt Setting time of siren Operation instruction 094 In the middle of the LCD region will show the original time default is 06 after input the instruction Re enter two digit time then input PROGRAM key for save System will back to program state Input other instructions for carry out other settings gt Setting telephone line detect disconnection function ON or OFF This function on when the telephone line is off or line has failed the upper left of the LCD will show Failure the siren will make sound at the same time Operation instruction 10 In the middle of the LCD region will show ON or OFF after input this instruction Input 1 for on show on Input 0 for off Press PROGRAM key for save after input has completed System will back to program state Input other instructions for carry out other settings gt Setting siren ON or OFF when there is a emergency alarm This function can set the siren ON or OFF when use the panic button or remote controller for emergency alarm Operation instruction 11 In the middle of the LCD region will how ON or OFF Default is ON after input this instruction Input 1 for ON Show ON Input 0 for OFF Press PROGRAM key for save after input has completed System will back to program state Input other instructi
12. his alarm host can work with our intelligent lock Before use need code the host and intelligent lock As follows Remove the USB key which for receiving from intelligent lock Insert the USB hole on the left of the alarm host USB key indicator light will flash quickly the indicator light will on after the code has completed take down the USB key then inset back to the intelligent lock Attention this operation no need press the CODE key Only insert the lock USB key to alarm USB hole to code A alarm system can only work with one intelligent lock 4 ARM alarm host AWAY ARM and HOME ARM mode Method one ARM by host panel A AWAY ARM Input system password then press AWAY ARM host will voice prompt AWAY ARM AWAY indicator light will flash After 30 seconds the light will on means system has enter into away arm state HOME ARM Input system password then press HOME ARM key host will voice prompt HOME ARM HOME indicator light will flash After 30 seconds the light will on means system has enter into home arm state Method two ARM by wireless remote controller Please refer to the former usage of wireless remote controller Method three ARM by phone from remote Using remote control the host must has remote control telephone numbers remote unlock totally three groups The phone must has calls display function at the same time 3 As follows using presetting remote
13. ith corresponding zone number prompt the user must solve the malfunction first then get into arm state Wire port order as below From right to left 12V GND Siren Siren Input Example shown A is close state open circuit alarm detector connection end of line resistor series connection with signal line B is open state closed circuit short circuit detector connection end of line resistor parallel connection with detector output port Note 1 Using wire detector must turn the corresponding switch to ON state switch which is next to the alarm host wire port please do not switch to OFF state Attention ON and OFF are not switch identification but the circuit board identification 2 The siren output port can connect with the 626 siren which sell in the market but have to pay attention to the positive and negative lines The wireless siren is optional 3 12V power output can provide power for wire detector need configure with 12 500ma DC 2 Telephone line and power connection There are two telephone line interface on the telephone host the top one is incoming line port another one is out line port incoming line port connect with outside telephone lines out line port connect with telephone Attention if the telephone connect with the network MODEM then the MODEM must connect with outlet port otherwise will affect the alarm host dial alarm numbers As shown below USB Hole Before using
14. nput this instruction input 5 or 6 then input telephone numbers Press PROGRAM key to save the system will back to program state Input other instructions to carry out other settings Description 5 or 6 means the first and the second detector low battery prompt telephone numbers gt Setting remote unlock remote control number This number use for when the user is not at home remote control this alarm host or unlock the intelligent lock the telephone which connect to the alarm host must has calls display function Only setted alarm phone number can control other number can t not control Operation instruction O3 The upper right series number flashing after input this instruction input 1 2 or 3 then input the telephone number Press PROGRAM key to save after input has completed System will back to program state Input other instruction to carry out other settings Description 1 2 or 3 mean the first the second or the third unlock number Telephone remote control functions 1 for arm 2 for disarm 5 for listen in 6 for unlcok gt Delete or change of the phone numbers When need delete or change the alarm center number user phone number and remote control unlock number operation instruction is same like setting instruction As follow The numbers will flashing when input the corresponding instruction If the phone number has already setted The number will show in the mid
15. nter has completed System will back to program state Input other instructions for carry out other settings gt Setting system time Operation instruction 15 After input this instruction month will flashing after input the month date will flashing complete the time setting according to the cursor move order the seconds can t change Press PROGRAM for save after enter has completed System will back to program state Input other instructions for carry out other settings The alarm host has build in lithium battery when the alarm electricity has off the system will keep setting history no need reset after re boot gt Setting alarm host auto arm time Operation instruction 16 Time will flash after input this instruction In turn enter the new time seconds can t set Press PROGRAM for save after enter has completed System will back to program state Input other instructions for carry out other settings When the auto arm function has open When the time has reached the setting time the alarm host will automatically enter into arm state gt Setting alarm host auto arm time Operation instruction 17 Time will flash after input this instruction In turn enter the new time seconds can t set Press PROGRAM for save after enter has completed System will back to program state Input other instructions for carry out other settings When the auto arm function has open When the time has reache
16. ons for carry out other settings gt Setting siren with voice prompt ON or OFF when use remote controller to arm or disarm This function can set for remote controller to am or disarm the voice prompt ON or OFF Operation instruction 12 In middle of LCD region will show ON or OFF after input this instruction input 1 for ON Show ON Input 0 for OFF Press PROGRAM for save after enter has completed System will back to program state Input other instructions for carry out other settings Attention When open the voice prompt alarm host which has build in or wire connected siren will have no voice prompt Only wireless siren has voice prompt gt Setting wireless siren function ON or OFF On the premise that the alarm host work with our factory wireless siren Can control the wireless siren ON or OFF by this setting Operation instruction 13 In middle of LCD region will show ON or OFF after input this instruction input 1 for ON Show ON Input 0 for OFF Press PROGRAM for save after enter has completed System will back to program state Input other instructions for carry out other settings gt Setting alarm host automatically arm or disarm ON or OFF This alarm host can set to automatically arm or disarm Operation instruction 14 In middle of LCD region will show ON or OFF after input this instruction input 1 for ON Show ON Input 0 for OFF Press PROGRAM for save after e
17. rder to avoid misstatement and omission The infrared detector using intelligent discriminant way can effectively prevent misstatement also has low power alarm and anti tamper function belong to new generation detectors 3 Wireless remote controller usage The remote controller has four buttons Away arm button Home arm button Disarm button Panic button ll 1 Press AWAY ARM button Alarm host with voice prompt away armed Execute delay arm away indicator light flashing for 30 seconds then light on Enter arm state 2 Press AWAY ARM button PANIC BUTTON enter into arm state away indicator light on 3 Press HOME ARM button Voice prompt home armed Execute delay arm home indicator oD light flash for 30 seconds then the light on enter into home arm state 4 Press HOME ARM button PANIC BUTTON 1 Enter inter arm state immediately home indicator light on 5 When press the PANIC BUTTON ll no matter what state the alarm host in arm or disarm the alarm host will alarm the alarm indicator light will on at the same time 6 Press DISARM button will disarm the alarm host immediately terminate ongoing alarm operation Attention In home arm state the detector in home mode when registered will alarm in away mode when registered will not alarm In away arm state no matter in home or away
18. s 7 group Include 2 groups of center number 3 groups of alarm number 2 groups of detector low battery prompt numbers 10 External alarm volume 2110dBspl 10 11 Working temperature 15 C 55 C Relative humidity lt 90 3 Alarm system Basic configuration 1 Alarm host with back up battery inside 1 PC 2 Wireless door sensor 1PC 3 Wireless remote controller 2 PCS 4 Wireless infrared detector 1 PC 5 Wire siren 1PC 6 English User manual 1 PC 7 Power supply 1PC 8 Telephone line 1 PC 9 Warranty Card 1 PC 10 2 2K carbon resister 4 PCS 4 Optional configuration 1 Wireless intelligent infrared detector 2 Wireless smoke detector wireless gas detector etc 3 Wireless siren 4 wired or wireless infrared fence and beam detector 5 Intelligent locks 6 Invisible security network II Installation of the alarm host 1 Alarm host installation CEGE 3805243195 d eode Few oe inanar 1D Bon j E OT AMM OR Meuget 2 O B AAAA O 9 N o QO Alarm host appearance Alarm host appearance 1 Wire detector connection according to different configuration some alarm host has no this function This alarm system has four wire detector input ports can choose open circuit alarm or short circuit alarm wire detector trigger alarm in away arm or home arm mode in disarm state when the detector has malfunction the alarm host can t enter into arm state the screen will flash w
19. ths now the new infrared detector battery can use for 3 years at the most 2 When the original detector has low battery the owner do not know initiative now the new infrared detector can dial the owner number to inform when there is alow battery and through the voice message to inform which detector need to change the battery in time 3 The original infrared detector is signal trigger alarm new infrared detector adopts human behavior identification make sure it s human then alarm effectively reduce the misstatement happens 4 The original wireless alarm system without timing arm or disarm function New alarm host have added this function 5 The original alarm host only support small wire siren New alarm host support small wire siren 626 big siren and wireless siren 6 Real Time clock the system will not lose the time setting when electricity has off 7 Remote control number identification only the owner can control from remote 1 Detailed basic function of the alarm host 1 Big LCD screen display Can display the date time alarm zone alarm type and other informations 2 Keyboard operation easy and applicable 3 Voice prompt function arm disarm or keyboard programming has voice prompt 4 Password operation Make sure the system is safe 5 Can connect with our company receiving alarm platform achieve networking management 6 Can presetting 3 groups of alarm phone number and 2 groups of alarm
20. u eB Handset icon means it is dialing alarm phone number the digits in the middle means the phone number being called the date in the left corner means alarm type 6 Alarm operation 1 Alarm call setting When the alarm host is alarming it will dial the setting alarm phone number in order when the alarm call has been connected The alarm host will play the voice prompt and inform the alarm type User can input the corresponding number to operation there is 6 voice prompt but press 6 will not unlock Press 1 for arm Press 2 for disarm Press 5 for listen in Press for hang up end up this alarm means dismiss this alarm But the host state will not change Do not enter any numbers and directly hang up Alarm host will dial next alarm phone number Attention When connected to the alarm host If no any operations for 30 seconds the alarm host will hang up automatically and dial the next alarm phone number 2 Disarm by remote controller Press the disarm button on the remote controller when dialing the alarm phone number will terminate the current alarm operation 3 Disarm by alarm panel Input the password to unlock the keyboard Then press the BACK DISARM key mean disarm 4 Alarm timeout automatically exit If the alarm host has dialed all of the alarm phone numbers for 5 times in a row still no effective alarm or disarm The alarm host will not dial any alarm phone n
21. umber exit the alarm and enter the standby mode 7 Remote control remote unlock function operation Using the phone number which has used or setting for remote control remote unlock to dial the connected phone alarm host will connect automatically phone display screen will show the incoming call number the alarm host will voice prompt to enter the password and doing corresponding operations Users have to enter the password first then end up with enter into function setting operation after the password is correct Pressing the follow keys can do the corresponding operations ARM 2 DISARM 5 LISENIN 6 REMOTE CONTROL After the alarm host has received the signal host will automatically unlock in 1 minute Hang up after operation Exit Attention Doing the above operations If the host voice prompt wrong password please input again should re enter the password again 8 System reset When need to restore the system to factory settings can use the system reset function reset as follow 1 Turn off the alarm host first then press the PROGRAM key to start Release the key when the host buzzer make beep beep beep tone for three times Press again then the host will voice prompt System Initialization complete means reset complete Special note Please do not use the system reset function in no special circumstances otherwise all of the parameters will reset to factory
Download Pdf Manuals
Related Search