Home

KTQM77/mITX – KTHM76/mITX Users Guide

1. Ee INN CLK SB3V3 ae e Ech 1 cso EIER ADDIN 10K EE ve NC ETSI IO VOS II ISOLATE t GND Description Serial Clock 3 3V Standby Voltage power line Normally output power but when Motherboard is turned off then the on board SPI Flash can be 3 3V power sourced via this pin CSO CSO Chip Select 0 active low ADDIN ADDIN input signal must be NC MOSI Master Output Slave Input The ISOLATE input active low is normally NC but must be connected to GND when ISOLATE loading SPI flash Power Supply to the Motherboard must be turned off when loading SPI flash The pull up resistor is connected via diode to 5VSB MISO Master Input Slave Output KTQM 77 KTHM76 Users Guide KTD NO850 F Page 56 Internal Connectors 6 14 XDP CPU Debug Port for CPU J32 The XDP CPU Intel Debug Port for CPU connector is not mounted and not supported XDP connector layout pads is located on the backside of PCB and is prepared for the Molex 52435 2671 or 52435 2672 Pin Signal Description Type Pull Up Down OBSFN_AO S OBSFN A1 GND A 5 6 GND PWR 7 NC NC 8 NC NC 9 GND PWR gt HOOK1 HOOK2 HOOK3 H
2. POST BIOS Beep Codes Number of Beeps 1 Memory refresh timer error Parity error in base memory first 64KB block Base memory read write test error Motherboard timer not operational Processor error 8042 Gate A20 test error cannot switch to protected mode General exception error processor exception interrupt error Display memory error system video adapter AMIBIOS ROM checksum error CMOS shutdown register read write error Cache memory test failed Description CO N o1 AION o Troubleshooting POST BIOS Beep Codes Number of Beeps 1 20r3 Reset the memory or replace with known good modules 4 7 9 11 Fatal error indicating a serious problem with the system Consult your system manufacturer Before declaring the motherboard beyond all hope eliminate the possibility of interference due to a malfunctioning add in card Remove all expansion cards except the video adapter If beep codes are generated when all other expansion cards are absent consult your system manufacturer s technical support If beep codes are not generated when all other expansion cards are absent one of the add in cards is causing the malfunction Insert the cards back into the system one at a time until the problem happens again This will reveal the malfunctioning card If the system video adapter is an add in card replace or reset the video adapter If the vide
3. name Pin Shows the pin numbers in the connector The graphical layout of the connector definition tables is made similar to the physical connectors Signal The mnemonic name of the signal at the current pin The notation XX states that the signal XX is active low Type Al Analogue Input AO Analogue Output I Input TTL compatible if nothing else stated lO Input Output TTL compatible if nothing else stated IOT Bi directional tristate IO pin IS Schmitt trigger input TTL compatible IOC Input open collector Output TTL compatible IOD Input Output CMOS level Schmitt triggered Open drain output NC Pin not connected O Output TTL compatible OC Output open collector or open drain TTL compatible OT Output with tri state capability TTL compatible LVDS Low Voltage Differential Signal PWR Power supply or ground reference pins loh Typical current in mA flowing out of an output pin through a grounded load while the output voltage is gt 2 4 V DC if nothing else stated lol Typical current in mA flowing into an output pin from a VCC connected load while the output voltage is lt 0 4 V DC if nothing else stated Pull U D On board pull up or pull down resistors on input pins or open collector output pins Note Special remarks concerning the signal The abbreviation TBD is used for specifications which are not available yet or which are not sufficiently specified by the c
4. KTD N0850 F BIOS Advanced 10 2 18 Advanced CPU PPM Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced CPU PPM Configuration Enable Disable Intel SpeedStep Turbo Mode Enabled CPU C3 Report Enabled CPU C6 Report Enabled CPU C7 Report Enabled Config TDP LOCK Disabled Long duration power limit 0 Long duration maintained 0 Short duration power limit 0 ACPI T State Disabled lt Select Screen Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Advanced Function Selection Description Disabled EIST Enabled Enable Disable Intel SpeedStep Turbo Mode Disabled Note1 Enabled Turbo Mode Disabl CPU C3 Report Sa Enable Disable CPU C3 ACPI C2 report to OS Enabled CPU C6 Report ee Enable Disable CPU C6 ACPI C3 report to OS Enabled CPU C7 Report Disabled Enable Disable CPU C7 ACPI C3 report to OS Enabled Disabled e Config TDP LOCK Enabled Lock the Config TDP Control register em Long duration power limit in Watts 0 means use Long duration power limit 0 255 Note2 factory default EL Time window which the long duration power is Long duration maintained 0 120 Note2 maihtalhicd A EM Short duration power limit in Watts 0 means
5. Ox20000000 Ox201FFFFF 200000 System board OxXE4000 OxXET7FFF 4000 BET bus 0xE0000 OxXE3FFF 4000 BET bus OxDC000 OxD8000 OxDFFFF OxDBFFF 4000 IC BEN bus bus 0xD4000 OXD7FFF P T bus 0xD0000 OxD3FFF PCI bus 0xA0000 KTQM 77 KTHM76 Users Guide OxXBFFFF Intel HD Graphics Family BET bus Ka o i L c o Ka o nc E o mn Ka gt We F N0850 KTD 9 3 Interrupt Usage 9ZIL 19H 8sn y 193U1 olpny UOnIUYSqj YBIH 03L IHOV VLVS AN I23U 9L3L v HOd 3003 319d ACHEN LAL Mod 3003 ECHTEN 1SOH IDHO b6EL IST VLAL 9 MOJ 1003 919d A IBIUI odeja uj ouIBuF pjuowobeuen BS TES UT OLAL L HOd J0O0Y 919d A IAU aza bI EE DIEU JOSS9IOJd Beeg IGOUounN esno N ZSd zza SNgnws ale SOIg ui uonosjes ENOD YIJEM JUIN JLI1 SOND wa sAS SOIg Ul uonoejes YNOD SOld ui uonosjes LWOJ SOIg ui uonoosjes ZWOJ pseoqAsy Z Sd Jeun W JS S KTD NO850 F System Resources 9 4 IO Map Address range hex Size hex Description OXOOOOFFFF Ox0000FFFF 1 Motherboard resources 0x0000F0DO 0x0000F0D7 8 Intel 7 port SATA AHCI 1E03 0x0000F0CO0 0x0000F0C3 4 Tatel e 7 port SATA ECH IROS 000007050 0x0000F0B7 8 Intel 7 port SATA
6. Hard Disk Driver Disabled Empty Unknown Enabled Disabled Disabled Hard Disk Driver lt Select Screen Change Opt F1 General Help Disabled Empty Unknown F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Spin Up Device Serial ATA Port 2 Software Preserve Port 2 Enabled Hot Plug Disabled External SATA Disabled Spin Up Device Disabled Version 2 15 1226 Copyright 2012 American Megatrends Inc Scroll indicator bar Note By scrolling down or up also settings for Serial ATA Port 3 5 can be accessed Selection Description Disabled Enabled IDE ACHI RAID Function SATA Controller s Enable or Disable SATA Device Determines how SATA controller s operate SES DISSI SENET RAID is supported by the KTQM77 mITX only Indicates the maximum speed the SATA controller can support SATA Controller Speed Note in the above BIOS menu the functions below the submenu Software Feature Mask Configuration will be described after the submenu description KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Advanced 10 2 5 1 Software Feature Mask Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced Enables or Disables RAIDO Enabled feature Enabled RAID1 RAID10 RAID5 Intel Rapid Recovery Technology OROM UI and BANNER HDD Unlock LED Locate IRRT Only on eSATA Smart Respo
7. 0x000000FF 10 Numeric data processor 0x000000E0 0x000000EF 10 Motherboard resources 0x000000C0 0x000000DF 20 Direct memory access controller 0x000000A2 0x000000BF Motherboard resources 0x000000A0 0x000000A1 Programmable interrupt controller 0x00000081 0x00000091 Direct memory access controller 0x00000072 0x00000080 Motherboard resources 0x00000070 0x00000077 System CMOS real time clock 0x00000067 0x00000067 Motherboard resources 0x00000065 0x00000064 0x00000065 0x00000064 Motherboard resources Standard PS 2 Keyboard 0x00000063 0x00000063 Motherboard resources 0x00000061 0x00000061 Motherboard resources 0x00000060 0x00000060 Standard PS 2 Keyboard 0x00000044 0x0000005F Motherboard resources 0x00000040 0x00000043 System Timer 0x00000022 0x00000022 0x0000003F 0x00000023 Motherboard resources Motherboard resources 0x00000020 0x00000021 Programmable interrupt controller 0x00000000 0x0000001F Direct memory access controller PCI bus KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Main 10 BIOS The BIOS Setup is used to view and configure BIOS settings for the board The BIOS Setup is accessed by pressing the Del key after the Power On Self Test POST memory test begins and before the operating system boot begins The BIOS settings will be lo
8. 2820QM SRO12 D2 100 45 418 1066 1333 6 2670QM SRO2N D2 100 45 4 8 1066 1333 1600 6 2720QM SRO14 D2 100 45 4 8 1066 1333 1600 6 2710QE SRO2T D2 100 45 418 1066 1333 6 2630QM SRO2Y D2 100 45 214 1333 1600 3 3380M SROX7 L1 105 35 2 4 1333 1600 3 3360M SROMV L1 105 35 214 1333 1600 3 3340M SROXA L1 105 35 2 4 1333 1600 3 3610ME SROQJ L1 105 35 214 1333 1600 3 3320M SROMX L1 105 35 2 4 1333 1600 3 3230M SROWY L1 105 35 2 4 1333 1600 3 3210M SROMZ L1 105 35 214 1066 1333 3 2540M SRO44 J1 100 35 2 4 1066 1333 3 2520M SRO48 J1 100 35 2 4 1066 1333 3 2510E SRO2U D2 100 35 2 4 1066 1333 3 2410M SRO4B J1 100 35 KTQM 77 KTHM76 Users Guide KTD N0850 F System Specification Thermal Design Power Processor Brand Core G 3 gen 1333 1600 1333 1600 1333 1600 1333 1600 1066 1333 1066 1333 1066 1333 1066 1333 1066 1333 1066 1333 1066 1333 1066 1333 1066 1333 SROQM 105 35 SRON2 90 35 NO DDO DO Mes Core i3 N Uw Www a GD OG G2 Oo CO 100 35 100 35 Celeron N AIAIAIAIAIAIAIA AAA RECA NINININININININ i oa Note Sufficient cooling must be applied to the CPU in order to remove the effect as listed in above table Thermal Guideline The sufficient cooling is also depending on the max
9. KTD NO850 F Page 128 BIOS Chipset 10 3 2 5 Memory Thermal Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc Memory Thermal Configuration Enable or disable Memory Thermal Management Disabled Disabled Disabled Disabled PECI Injected Temperature EXTTS via TS on Board EXTTS via TS on DIMM Virtual Temperature Sensor VTS lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description Memory Thermal Disabled Enable or disable Memory Thermal Management Enabled Management Enabled Enable or disable memory temperatures to be ELSE ESE TS alge sue Disabled injected to the processor via PECI Enabled Enable or disable routing TS on Board to be Disabled injected to EXTTS pins on the PCH Enabled Enable or disable routing TS on DIMM to be Disabled injected to pin on the PCH EXT TS via TS on Board EXTTS via TS on DIMM Virtual Temperature Enabled Enable or disable Virtual Temperature Sensor Sensor VTS Disabled VTS KTQM 77 KTHM76 Users Guide KTD N0850 F Page 129 BIOS Chipset 10 3 2 6 GT Power Management Control Aptio Setup Utility Copyright 2012 American Megatrends Inc GT Power Management Control
10. Memory e DDR3 SODIMM 204pin socket 2 sockets e Support single and dual ranks DDR3 1066 1333 1600MT s PC3 8500 PC3 10600 PC3 12800 e Support system memory from 256MB and up to 2x 8GB Notes Less than 4GB displayed in System Properties using 32bit OS Shared Video Memory PCI resources is subtracted e ECC not supported PGA processors do not support ECC Chipset Intel QM77 HM77 PCH Platform Controller Hub Intel amp VT d Virtualisation Technology for Directed UO Intel amp TXT Trusted Execution Technology Intel amp vPRO KTQM 7 only Intel amp AMT Active Management Technology version 8 0 KTQM 7 only Intel amp AT Anti Theft Technology Intel amp HD Audio Technology Intel amp RST Rapid Storage Technology Intel amp RRT Rapid Recover Technology SATA Serial ATA 6Gb s and 3Gb s USB revision 2 0 USB revision 3 0 PCI Express revision 2 0 ACPI 3 0b compliant Dual or Triple Display support Dual Triple Graphic Pipes depends on CPU Blue ray HD video playback Security e Intel Integrated TPM 1 2 support Management e Intel Active Management Technology Intel AMT 8 0 KTQM77 only Audio 7 1 Channel High Definition Audio Codec using the VIA VT1708S codec Line out Line in Surround output SIDE LFE CEN BACK and FRONT Microphone MIC1 and MIC2 CDROM in SPDIF electrical Interface only On board speaker Electromagnetic Sound Generator like Hycom HY O5LF KTQM 77 KTHM 6
11. Yes REZON 4x USB3 0 2 0 Use of this Users Guide implies a basic knowledge of PC AT hard and software This manual is focused on describing the KTQM77 board s special features and is not intended to be a standard PC AT textbook New users are recommended to study the short installation procedure stated in the following chapter before switching on the power All configuration and setup of the CPU board is either done automatically or manually by the user via the BIOS setup menus Only exception is the Load Default BIOS Settings Jumper KTQM 77 KTHM76 Users Guide KTD NO850 F Page 8 Installation procedure 1 Installation procedure 1 1 Installing the board To get the board running follow these steps If the board shipped from KONTRON has already components like RAM CPU and cooler mounted then relevant steps below can be skipped 1 Turn off the PSU Power Supply Unit Warning Turn off PSU Power Supply Unit completely no mains power connected to the PSU or leave the Power Connectors unconnected while configuring the board Otherwise components RAM LAN cards etc might get damaged If not using single 12V power input make sure PSU has 3 3V monitoring watchdog standard ATX PSU feature running the board without 3 3V will damage the board within minutes 2 Insert the DDR3 DIMM 204pin SODIMM module s Be careful to push it in the slot s before locking the tabs For a list of approved DDR3 SODIMMs cont
12. 10 2 7 Advanced AMT Configuration ener een en nennen nennen ner nennen enn 81 10 2 8 Advanced Acoustic Management Configuration ssssssssseseeneenenm nennen 83 10 2 9 Advanced USB ConfigUratlon i uuu iod et eren b e ep tree np dei sok deze ea erede epa aa ski kasab pk diss bade 84 10 2 10 Advanced SMART Settings eene ok pake d ok is ab ak kone sake eue dh eed a e dde FR d ed RR e 4 Rh d as ua 86 10 2 11 Advanced Super IO Confouraton nennen ener ener nennen nennt 87 10 2 12 Advanced Voltage Monitor nenne enne nerrnen nennen nennen nenne enn 93 10 2 13 Advanced Hardware Health Conbouraton eene een nennen 94 10 2 14 Advanced Displayblock SetuP iride aite tte k bd pw ad dak ak kisa kid e ke k an pad din Epl d Tu aida 96 10 2 15 Advanced LAN Configuration iiie pea ea kon ka nice tho sweet ni rev hdd a be d i dees ak e d ak kd 97 KTQM 77 KTHM76 Users Guide 10 2 16 Advanced Delay Startup ke pi aie e Eee iin eerte ea Ene teda de da po a paka pinn 99 10 2 17 Advanced Serial Port Console Redirection ooo tsseaooo ssasooooesesoonosssaoasonsaann 100 10 2 18 Advanced CPU PPM Configuration scie pl din n oo ak e n Coes kn in D TER pa tenes 104 DOUZ CMP E 106 10 3 1 PCH 10 Comfightation iuc ices pwa via ee cto ara ao k daso ip Eden ru dan pie Pay kidnap taa pi RE REES 107 10 3 2 System Agent SA Configuration eka kdk kan Don aki kaye kaa aia a n nb Le on ka ia gk dd a aded aka 113 UN
13. Control the PCI Express Root ASPM Support Disabled Port PME SCI Enabled PCIe Speed Auto lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Selection Description PCI Express Root Port 1 Disabled 4 6 8 Enabled Control the PCI Express Root Port dimus Set the ASPM Level Disabled Disabled ASPM ASEM UERR LOs Force all links to LOs State LOsL1 Auto BIOS auto configure Auto PME SCI Lush Enable or disable PCI Express PME SCI Enabled Auto PCle Speed Gen1 Select PCI Express port speed Gen2 KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Chipset 10 3 1 2 USB Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc USB Configuration Enable or disable XHCI Pre Boot Driver support xHCI Mode Smart Auto HS Port 1 Switchable Enabled HS Port 2 Switchable Enabled HS Port 3 Switchable Enabled HS Port 4 Switchable Enabled xHCI Streams Enabled ECHI1 Enabled ECHI2 Enabled lt Select Screen USB Ports Per Port Disable Control Disabled 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc KTQM 77
14. IO 2F8h IRQ 3 4 5 6 7 10 11 12 IO 3E8h IRQ 3 4 5 6 7 10 11 12 IO 2E8h IRQ 3 4 5 6 7 10 11 12 Standard Serial Port Mode IrDA 1 0 HP SIR Mode ASKIR Mode Note1 only if Serial Port Enabled KTQM 77 KTHM76 Users Guide Description Enable or Disable Serial Port COM Select an optimal setting for Super IO device Change the Serial Port mode Select lt High Speed gt or lt Normal mode gt mode KTD NO850 F Page 92 BIOS Advanced 10 2 11 5 Parallel Port Configuration Note Parallel Port is not available connector not mounted Aptio Setup Utility Copyright O 2012 American Megatrends Inc Advanced Parallel Port Configuration Enable or Disable Parallel Port LPT LPTE Device Settings IO 378h IRQ 5 Change Settings Auto Device Mode Standard Parallel lt Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description Disabled Enable or Disable Parallel Port Enabled LPT LPTE Auto 10 378h IRQ 5 IO 378h IRQ 7 10 11 12 IO 278h IRQ 5 6 7 10 11 12 Select an optimal setting for Super IO IO 3BCh IRQ 5 6 7 10 11 12 device 10 378h 10 278h IO 3BCh Standard Parsllel Port Mode EPP Mode ECP Mode EPP Mode amp ECP Mode Parallel Port Change Settin
15. It is required to use only HiSpeed USB cable specified in USB2 0 standard on Twisted Power Pair Polyvinyl Chloride PVC Jacket Red Vaus Black Power Ground Outer Shield gt 65 Interwoven Tinned Copper Braid Inner Shield Aluminum Metallized Polyester Twisted Signaling Pair White D Green D 28 AWG Tinned Copper Drain Wire 6 6 1 USB Connector 6 7 See Frontpanel Connector FRONTPNL description KTQM77 mlTX only 6 6 2 USB Connector 8 9 USB8 9 J10 USB Ports 8 and 9 are supplied on the internal USB8 9 pinrow connector J10 Note Type Signal PIN Signal Type Note 5V SB5V 5V SB5V PWR 1 1 USB8 3 USB9 USB8 f6 USB9 7 9 GND GND NC NC Signal Description USB8 USB8 USB9 USB9 Differential pair works as Data Address Command Bus DV supply for external devices SB5V is supplied during powerdown to allow 5V SB5V wakeup on USB device activity Protected by resettable 1A fuse covering both USB ports KTQM 77 KTHM76 Users Guide KTD N0850 F Page 44 Internal Connectors 6 6 3 USB Connector 10 11 USB10 11 J11 USB Ports 10 and 11 are supplied on the internal USB 10 11 pinrow connector J11 Note Type Signal 10 USB10 l0 USB10 PWR GND eee KEY Signal Description USB10 USB10 USB11 USB11 Differential pair works as Data Address Command Bus 5V supply for external devices SB5V is supplie
16. KTHM76 Users Guide KTD N0850 F BIOS Chipset Function Selection Description Enabled Enable or disable XHCI Pre Boot Driver XHCI Pre Boot Driver Disabled support Smart Auto Auto xHCI Mode Mode of operation of xHCI controller Enabled Disabled HS Port 1 Switchable GE for HS port switching between xHCI and HS Port 2 Switchable HS Disabled i a Port 3 Switchable HS Port Enabled EE If HS port is routed to xHCI the corresponfing 4 Switchable Note1 En Disabled Enable xHCI Maximum Primary Stream Array xHCI Streams Enabled Size ECHI1 Disabled Control the USB EHCI USB 2 0 functions Enabled One EHCI controller must always be enabled ECHI2 Disabled Control the USB EHCI USB 2 0 functions Enabled One EHCI controller must always be enabled USB Ports Per Port Disabled Control each of the USB ports 0 13 Disable Control Enabled disabling USB Port 0 13 Disabled Disabled Note2 Enabled Disabled USB port Note1 Not visible if xHC Mode is Disabled Note2 Only visible if USB Ports Per Port Disable Control is Enabled The USB6 and USB7 are not supported by the KTHM76 mITX KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Chipset 10 3 1 3 PCH Azalia Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc PCH Azalia Configuration Control Detection of the Azalia device Disabled Azalia will be Audio Jack Sensing Auto uncondition
17. Protected by resettable 2A fuse covering both USB ports KTQM 77 KTHM76 Users Guide KTD N0850 F Page 35 IO Area Connectors 5 3 2 USB Connector 2 3 USB2 3 USB Ports 2 and 3 are mounted together with DP1 port and supports USB3 0 USB2 0 Note Type Signal PIN Signal Type Note e LI EH USB3 7 men EE RX3 EOE 13 RX3 TX3 GND USB2 1 USB2 PWR ZE 1 2 3 4 RX2 BCEE Note 1 In order to meet the requirements of USB standard the 5V input supply must be at least 5 00V Description USB2 USB2 RX2 RX2 TX2 TX2 USB3 USB3 RX3 RX3 TX3 TX3 Differential pair works as Data Address Command Bus 5V supply for external devices SB5V is supplied during powerdown to allow 5V SB5V wakeup on USB device activity Protected by resettable 2A fuse covering both USB ports 5 3 3 USB Connector 4 5 USB4 5 USB Ports 4 and 5 are mounted together with ETH1 port and supports USB2 0 Note Type i i Type Note mus aerer ENKNENEN op PWA USB5 USB5 10 WR 5V SB5V KENNEN GND USB4 USB4 IO Note 1 In order to meet the requirements of USB standard the 5V input supply must be at least 5 00V Signal Description USB4 USB4 USB5 USB5 Differential pair works as Data Address Command Bus 5V supply for external devices SB5V is supplied during powerdown to allo
18. Short duration power limit 0 255 Note2 use factory default ACPI T State iere Enable Disable ACPI T State support Enabled Note1 Not present when using Intel Celeron B810 CPU or i3 Core CPU Note2 To enter number use digit keys KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Chipset 10 3 Chipset Aptio Setup Utility Copyright 2012 American Megatrends Inc W Chipset JE he PCH Parameters System Agent SA Configuration Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright O 2012 American Megatrends Inc KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Chipset 10 3 1 PCH IO Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc Intel PCH RC Version PCI Express Configuration Intel PCH SKU Name settings Intel PCH Rev ID gt USB Configuration PCH Azalia Configuration Restore AC Power Loss Power On Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Note Intel PCH SKU Name depends on the actual board type QM77 or HM76 Please fid description of the PC Express Configuration USB Configuration and PCH Azalia Conf
19. The KTOM77 mITX supports one PCle x1 Type Note 12V 12V GND SMB_CLK SMB_DATA GND 3V3 JTAG TEST Z 3V3 Dual WAKE ENS B12 A12 B13 A13 PCIE_CLK_P Ge SE B14 A14 PCIE_CLK_N PCIE_TXN B15 A15 GND GND PCIE_RXP CLK_REQ PCIE_RXN GND GND Note 1 10K ohm pull up to 3V3 Dual Note 2 4K7 ohm pull down to GND KTQM 77 KTHM76 Users Guide KTD N0850 F Page 63 Onboard mating connector 8 On board amp mating connector types The Mating connectors Cables are connectors or cable kits which are fitting the On board connector The highlighted cable kits are included in the KTQM67 Cable amp Driver Kit PN 826598 in different quantities depending on type of connector For example there is 4 x 821017 COM cables and 6 x 821035 SATA cables On board Connectors Mating Connectors Cables Connector Manufacturer Manufacturer FAN_CPU Foxconn HF2704E M1 1375820 4 4 pole FAN_SYS AMP 1470947 1 1375820 3 3 pole 22 23 2061 Molex 22 01 2065 KBDMSE Kontan KT 1046 3381 KT 1053 2384 CDROM Foxconn HF1104E Molex 50 57 9404 Molex 70543 0038 SATA Hon Hai LD1807V S52T Molex 67489 8005 Kontron KT 821035 cable kit ATXPWR Molex 44206 0002 Molex 5557 24R Don Connex C44 40BSB1 G Don Connex A32 40 C G B 1 Kontron KT 9
20. 0 5 Shield PWR 20 NC NC 21 NC NC 22 TMDS Clock Shield PWR 23 TMDS Clock Digital clock Link 1 LVDS OUT 24 TMDS Clock Digital clock Link 1 LVDS OUT C1 ANALOG RED Analog output carrying the red color signal O TSR C2 ANALOG GREEN Analog output carrying the green color signal O T5R C3 ANALOG BLUE Analog output carrying the blue color signal O T5R C4 ANALOG HSYNC CRT horizontal synchronization output O C5 ANALOG GND Ground reference for RED GREEN and BLUE PWR C6 ANALOG GND Ground reference for RED GREEN and BLUE PWR Note The 5V supply is fused by a 1 1A resettable fuse KTQM 77 KTHM76 Users Guide KTD N0850 F IO Area Connectors 5 1 2 DP Connectors DPO DP1 J40 J39 The DP DisplayPort connectors are based on standard DP type Foxconn 3VD51203 H7JJ 7H or similar Type Note LVDS PWR LVDS LVDS PWR LVDS LVDS PWR LVDS Pin Signal Description Lane 0 p GND Lane O0 n Lane 1 p GND Lane 1 n Lane 2 p GND Lane 2 n Lane 3 p GND Lane 3 n Internally pull down 1Mohm Aux channel on pin 15 17 selected as default when NC DDC channel on pin 15 17 If HDMI adapter used 3 3V Internally connected to GND AUX channel used by DP DDC CIk used by HDMI Aux or DDC selection Not used Aux Channel or DDC Clk Config1 Config2 Aux Ch p GND Aux Ch n Aux Channel or DDC Data AUX channel used by DP DDC Data used by HDMI Hot Plug Int
21. 1 5A resetable PTC fuse KTQM 77 KTHM76 Users Guide KTD N0850 F Internal Connectors Page 41 6 4 2 LVDS Flat Panel Connector LVDS J20 The LVDS connector is based on 40 pole connector type Don Connex C44 40BSB1 G Note PIN Note Type Signal Signal Type Max 0 5A PWR 12V 12V PWR Max 0 5A Max 0 5A PWR 12V 12V PWR Max 0 5A Max 0 5A PWR 12V GND PWR Max 0 5A Max 0 5A PWR 5V GND PWR Max 0 5A Max 0 5A PWR LCDVCC LCDVCC PWR Max 0 5A 2K20 3 3V DDC CLK DDC DATA OT 2K20 3 3V 3 3V level OT BKLTCTL EEEE VDD ENABLE OT 3 3Vlevel 3 3V level OT BKLTEN GND PWR Max 0 5A LVDS LVDS A0 LVDS A0 LVDS LVDS LVDS A1 LVDS A1 LVDS LVDS LVDS A2 LVDS A2 LVDS LVDS LVDS ACLK WEE LVDS ACLK LVDS LVDS LVDS A3 LVDS A3 LVDS Max 0 5A PWR GND GND PWR Max 0 5A LVDS LVDS B0 LVDS BO LVDS LVDS LVDS B1 LVDS B1 LVDS LVDS LVDS B2 LVDS B2 LVDS LVDS LVDS BCLK REI LVDS BCLK LVDS LVDS LVDS B3 ER LVDS B3 LVDS Max 0 5A PWR GND 39 40 GND PWR Max 0 5A Note The KTQM 77 on board LVDS connector supports single and dual channel 18 24bit SPWG panels up to the resolution 1600x1200 or 1920x1080 and with limi
22. 11 Lane 12 Lane 13 Lane 14 Lane 15 lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit OO OO OO OO OO OO OO OO OO OO OO OO OO OO d Version 2 15 1226 Copyright O 2012 American Megatrends Inc KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Chipset Aptio Setup Utility Copyright 2012 American Megatrends Inc PEG Gen3 Endpoint Preset Value each Lane Value for Lane 0 Lane 1 Lane 2 Lane 3 Lane 4 Lane 5 Lane 6 Lane 7 Lane 8 Lane 9 Lane 10 Lane 11 Lane 12 Lane 13 Lane 14 Lane 15 lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit cxx TE a li Sa ll cx Version 2 15 1226 Copyright 2012 American Megatrends Inc KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Chipset Aptio Setup Utility Copyright 2012 American Megatrends Inc PEG Gen3 Endpoint Hint Value each Lane Value for Lane 0 Lane 1 Lane 2 Lane 3 Lane 4 Lane 5 Lane 6 Lane 7 Lane 8 Lane 9 Lane 10 Lane 11 Lane 12 Lane 13 Lane 14 Lane 15 lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit ba bo b2 b2 b2 bO bO bO bO bO bO bO bO bO WD Versi
23. 5 6 7 10 11 12 IO 2ES8h IRQ 3 4 5 6 7 10 11 12 Note1 only if Serial Port Enabled KTQM 77 KTHM76 Users Guide KTD N0850 F Page 89 BIOS Advanced 10 2 11 2 Serial Port 2 Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced Serial Port 2 Configuration Enable or Disable Serial Port COM Device Settings IO 2F 8h IRQ 3 Change Settings Auto lt Select Screen Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description Serial Port Disabled Enable or Disable Serial Port Enabled COM Auto IO 2F8h IRQ 3 IO 3F8h IRQ 3 4 5 6 7 10 11 12 Select an optimal setting for Super IO 2F8h IRQ 3 4 5 6 7 10 11 12 IO device IO 3E8h IRQ 3 4 5 6 7 10 11 12 IO 2ES8h IRQ 3 4 5 6 7 10 11 12 Change Settings Note1 Note1 only if Serial Port Enabled KTQM 77 KTHM76 Users Guide KTD NO850 F Page 90 BIOS Advanced 10 2 11 3 Serial Port 3 Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced Serial Port 3 Configuration Enable or Disable Serial Port COM Device Settings IO 8E8h IRQ 7 Change Settings Auto Device Mode Standard Serial Po lt Select Screen Change Opt F1 General Help F2 Previous Value
24. 9 PEG TXN 9 GND GND PEG TXP 10 PEG TXN 10 GND GND PEG TXP 11 PEG TXN 11 GND GND PEG TXP 12 PEG TXN 12 GND GND PEG TXP 13 PEG TXN 13 GND GND PEG TXP 14 PEG TXN 14 GND GND PEG TXP 15 PEG TXN 15 GND CLKREQ NC B36 B37 B38 B39 B40 B41 B42 B43 B44 B45 B46 B47 B48 B49 B68 B69 Bo B71 B72 B73 B74 B75 B76 B77 B78 B79 B80 B81 B82 A36 A37 A38 A39 A40 A41 A42 A43 A44 A45 A46 A47 A48 PEG_RXNI4 GND GND PEG RXP 5 PEG RXN 5 GND GND PEG RXP 6 PEG RXN 6 GND GND PEG RXP 7 PEG RXN 7 GND NC GND PEG RXPI8 PEG RXN 8 GND GND PEG RXP 9 PEG RXN 9 GND GND PEG RXP 10 PEG RXN 10 GND GND PEG RXP 11 PEG RXN 11 GND GND PEG RXP 12 PEG RXN 12 GND GND PEG RXP 13 PEG RXN 13 PEG RXP 14 PEG RXN 14 GND GND PEG RXP 15 PEG RXN 15 GND KTQM 77 KTHM76 Users Guide KTD N0850 F Page 60 Slot Connectors 7 1 2 miniPCl Express mPCle0 J34 The miniPCI Express port mPCle0 is located on the backside Beside miniPCle cards the mPCleO also supports mSATA SSD cards SATA2 is used for mSATA signals Note no USB signals
25. F System Specification Hardware Smart Fan control system support Thermal and Speed cruise for two on board Monitor Fan connectors CPU Fan on board and System Fan on board Subsystem Smart Fan control system support Speed cruise for two off board Fans Fan3 Fan4 via Feature Connector Three thermal inputs CPU Die temperature precision 3 C System temperature precision 3 C and System Temperature External via Feature Connector precision 19C Voltage monitoring Intrusion Case Open detect input via Feature connector Sleep S5 Indication via Feature connector System Powergood Signal via Feature connector Power ATX BTX w ATX 12V PSU for full PCI PCle load Supply Unit Alternatively mITX version only 12V single supply via ATX 12V 4 pole connector but with limitation to power load especially 5V for USB Battery Exchangeable 3 0V Lithium battery for on board Real Time Clock and CMOS RAM Manufacturer Panasonic Part number CR 2032L BN CR2032N BN or CR 2032L BE Approximate 6 2 years retention Current draw is 4 1uA when PSU is disconnected and 0 pA in SO S5 CAUTION Danger of explosion if the battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions Kontron Technology AMI BIOS EFI core version Support for ACPI 3 0 Advanced Configuration an
26. Firmware and BIOS Support Intel Anti theft Technology Intel Gigabit LAN Connect Intel AMT 8 0 EN Optional Intel Small Business Advantage More detailed block diagram on next page KTQM 77 KTHM76 Users Guide KTD N0850 F 2x SODIMM DDR3 Sandy Bridge or Ivy Bridge Processor Embedded DisplayPort rPGA 2x DisplayPort L DVI I 4x USB3 0 USB2 0 QM77 mem or HM76 10x USB2 0 QM77 PCH 8x USB2 0 HM76 VIA Audio Codec SPI BIOS Flash _ TPM Infineon System Specification PCle x16 x16slot PCle x1 mPCle no USB mPCle mSATA no USB PCle to Firewire 2x IEEE 1394a 1x 10 100 Gbe 2x 10 100 Gbe QM77 2x SATA3 0 4x SATA2 0 mSATA SATA2 signals mPCle connector RAID 0 1 5 10 QM77 Feature connector SMBus I2C Nuvoton Embedded 1 GPIO DAC ADC PWM W83627DHG Controller GPIO expansion up to 152 ITE8516 Intruder COM3 8 COM4 COM1 8 COM2 2x Fan CPU System 6 pin PS 2 KTQM 77 KTHM76 Users Guide KTD N0850 F System Specification 2 3 Processor Support Table KTQM 7 is designed to support the following PGA 988 processors up to 55W power consumption 2 3 generation Intel Core i7 processor 2 13 generation Intel Core i5 processor 2 3 generation Intel Core i3 processor Intel Celeron processor In the following list you will find all CPU s supported by the chipset in accord
27. M SENSE 1 4K7 12V PWR d GND PWR L E Signal Description Tacho signal from the fan for supervision The signals shall be generated by an open collector transistor or similar On board is a pull up resistor 4K7 to 12V The signal has to be pulsed typically twice per rotation 12V supply for fan A maximum of 2000mA can be supplied from this pin Power Supply GND signal KTQM 77 KTHM76 Users Guide KTD NO850 F Page 39 Internal Connectors 6 3 PS 2 Keyboard and Mouse connector KBDMSE J27 Attachment of a PS 2 keyboard mouse can be done through the pinrow connector KBDMSE J27 Both interfaces utilize open drain signalling with on board pull up The PS 2 mouse and keyboard is supplied from SB5V when in standby mode in order to enable keyboard or mouse activity to bring the system out from power saving states The supply is provided through a 1 1A resettable fuse KBDCLK IOD A4mA 2K77 KBDDAT i IOD M4mA 2K7 MSCLK Op A4mA 27 T 4 MSDAT IOD 14mA i 2K7 5V SB5V PWR O GND PWR JL s Signal Description Keyboard 8 and mouse Connector KBDMSE Description MSCLK Bi directional clock signal used to strobe data commands from to the PS 2 mouse MSDAT Bi directional serial data line used to transfer data from or commands to the PS 2
28. Note1 Only visible if external temperature sensor like PN1053 4925 Cable Temperature Sensor 44P 400 mm is connected Note2 Only visible if external temperature sensor is connected and if System Temperature Ext Type is not Disabled Note3 C if Fan Cruise Control Thermal use either digit keys to enter value or keys to increase decrease value Don t use mix of digit keys and keys Note4 RPM if Fan Cruise Control Speed use either digit keys to enter value or keys to increase decrease value by 100 Don t use mix of digit keys and keys Note5 Only visible if external temperature sensor is connected and if System Fan Cruise Control is Thermal Note6 Use number keys to enter value Note7 Only visible if CPU Fan Cruise Control is Thermal Note8 Seconds use digit keys to enter value Value 0 means Watchdog is disabled Refer to KT API V2 User Manual to control the Watchdog via API or refer to KT API V2 User Manual DLL how to control Watchdog via Windows DLL KTQM 77 KTHM76 Users Guide KTD N0850 F Page 96 BIOS Advanced 10 2 14 Advanced Displayblock Setup Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced Displayblock Setup Backlight Signal Inversion Disabled lt Select Screen Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 Ame
29. RAID volume TRIM is for SSD data garbage handling SATA connector pinning SATAO J21 SATA1 J22 SATA2 J23 SATA3 J24 SATA4 J25 and SATA5 J26 loh lol GND SATA TX SATA TX GND SATA RX SATA RX GND Signal Description SATA RX Host transmitter differential signal pair SATA RX SATA TX Host receiver differential signal pair SATA TX specifies 0 1 2 3 4 5 depending on SATA port Available cable kit KTQM 77 KTHM76 Users Guide KTD NO850 F Page 43 Internal Connectors 6 6 USB Connectors USB The KTQM77 board contains two EHCI Enhanced Host Controller Interface host controllers EHCI1 and EHCI2 that support up to fourteen USB 2 0 ports allowing data transfers up to 480Mb s Legacy Keyboard Mouse and wakeup from sleep states are supported Over current detection on all fourteen USB ports is supported Note that four USB 3 0 ports are shared with four of the USB 2 0 ports USBO USB3 from the EHCI1 The following USB ports are available on Internal Pinrows USB Port 6 and 7 KTQM77 mITX only via EHCI1 are supplied on the USB6 7 internal pinrow FRONTPNL connector USB Port 8 and 9 via EHCI2 are supplied on the USB8 9 internal pinrow connector USB Port 10 and 11 via EHCI2 are supplied on the USB10 11 internal pinrow connector USB Port 12 and 13 via EHCI2 are supplied on the USB12 13 internal pinrow connector Note
30. Status NOT INSTALLED Enter Select HDD Master Pwd Status INSTALLED Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description Set HDD User Password Set User Password Create New Password Advisable to Power Cycle System after Setting Hard Disk Passwords KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Save amp Exit 10 6 Save amp Exit This Menu is special having no selections for each function or in other words the function is the same as the selection Aptio Setup Utility Copyright 2012 American Megatrends Inc Main Advanced Chipset Boot Security Save amp Exit Exit system setup after saving Discard Changes and Exit the changes Save Changes and Reset Discard Changes and Reset Save Options Save Changes Discard Changes Restore Defaults Save as User Defaults Restore User Defaults Boot Override Select Screen PO ST3120827AS Launch EFI Shell From filesystem device Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Description Save Changes and Exit Exit system setup after saving the changes Discard Changes and Exit Exit system setup without saving any changes Save Changes and Res
31. Technology Technology Enabled 2 Seconds 4 Seconds If enabled indicates the delay of the OROM UI SE 6 Seconds Splash Screen in normal status 8 Seconds KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Advanced Remaining SATA Configuration menu description Function Port 0 Selection Disabled Enabled Description Enable or Disable SATA Port Hot Plug Disabled Enabled Designates this port as Hot Pluggable External SATA Disabled Enabled External SATA Support SATA Device Type Spin Up Device Hard Disk Drive Solid State Drive Disabled Enabled Identify the SATA port is connected to Solid State Drive or Hard Disk Drive On an edge detect from 0 to 1 the PCH starts a COMRESET initialization sequence to the device Port 1 Disabled Enabled Enable or Disable SATA Port Hot Plug see same function above see same function above External SATA see same function above SATA Device Type see same function above see same function above Spin Up Device Hot Plug see same function above Disabled Enabled see same function above see same function above see same function above Enable or Disable SATA Port see same function above External SATA see same function above see same function above Spin Up Device Port 3 see same function above Disabled Enabled see same function abo
32. This has no effect if external graphics present Secondary boot display selection will EFP3 DP2 display appear based on your selection EFP2 DP1 default 2 VGA modes will be supported only on LFP2 primary display VBIOS Default 640x480 LVDS 800x600 LVDS 1024x768 LVDS1 1280x1024 LVDS 1400x1050 RB LVDS1 1400x1050 LVDS2 1600x1200 LVDS Select LCD panel used by Internal LCD Panel Type 1366x768 LVDS Graphics Device by selecting the 1680x1050 LVDS appropriate setup item 1920x1200 LVDS 1440x900 LVDS 1600x900 LVDS 1024x768 LVDS2 1280x800 LVDS 1920x1080 LVDS 2048x1536 LVDS VBIOS Default 1024x768 SDVO LFP Select SDVO panel used by Internal SDVO LFP Panel Type 1280x1024 SDVO LFP Graphics Device by selecting the 1400x1050 SDVO LFP appropriate setup item 1600x1200 SDVO LFP AU Select the LCD panel scaling option used Penal eel of by Internal CLE EEN i Force Scaling PWM Inverted PWM Normal Backlight Control GMBus Inverted GMBus Normal Backlight Control Setting Auto Disabled Level 1 Auto GMCH use VBT defaults BIA Level 2 Level n Enabled with n Level 3 ggressiveness Level Level 4 Level 5 Off Spread Spectrum clock Hardware Spread is controlled by chip Hardware Chip Software Spread is controlled by BIOS Software KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Chipset Function Selection Description VBIOS Default NTSC_M NTSC_M_J N
33. are available CLKREQ GND PCIE_mini CLK PCIE_mini CLK GND ORNMDOPOFN ANA ees NC NC GND W_Disable PCIE_RXN RST PCIE_RXP 3V3 Dual GND GND GND 1 5V PCIE_TXN SMB_CLK SMB_DATA PCIE TXP GND GND 3V3 Dual 3V3 Dual GND CLK_MPCIE DATA_MPCIE RST_MPCIE SEL_MSATA Note 1 10K ohm pull up to 3V3 Note 2 2K2 ohm pull up to 3V3 Dual Note 3 100K ohm pull up to 1V8 SO mode KTQM 77 KTHM76 Users Guide Slot Connectors KTD N0850 F Page 61 7 1 3 miniPCl Express mPCle1 J35 The miniPCI Express port mPCle1 is located on the backside Note no USB and no mSATA signals are available Note Type Signal WAKE 2 NC NC 4 NC NC 6 1 CLKREQ 8 PWR GND 10 PCIE_mini CLK 12 PCIE_mini CLK 14 PWR GND 16 NC NC NC NC W_Disable PWR GND RST PCIE_RXN 3V3 Dual PCIE RXP GND PWR GND 1 5V PWR GND SMB_CLK PCIE_TXN SMB_DATA PCIE TXP PWR NC NC NC NC NC NC NC NC Note 1 10K ohm pull up to 3V3 Dual Note 2 2K2 ohm pull up to 3V3 Dual KTQM 77 KTHM76 Users Guide KTD NO850 F Page 62 Slot Connectors 7 1 4 PCI Express x1 Connector PCle x1 J36
34. combined USB2 USB3 and DP1 connector USB Port 4 and 5 via EHCI1 are supplied on the combined ETH1 USB4 and USB5 connector Note For USB2 0 cabling it is required to use only HiSpeed USB cable specified in USB2 0 standard on Twisted Power Pair Polyvinyl Chloride PVC Jacket Red Vous Black Power Ground Outer Shield gt 65 Interwoven Tinned Copper Braid Inner Shield Aluminum Metallized Polyester Twisted Signaling Pair White D Green D 28 AWG Tinned Copper Drain Wire For USB3 0 cabling it is required to use only HiSpeed USB cable specified in USB3 0 standard UTP Signal Pair Filler SDP Signal Pair Jacket SDP Signal Pair Ground KTQM 77 KTHM76 Users Guide KTD N0850 F IO Area Connectors 5 3 1 USB Connector 0 1 USB0 1 USB Ports 0 and 1 are mounted together with DPO port and supports USB3 0 USB2 0 Note Type Signal PIN Signal Type Note po EM USB1 me PWR 5V SB5V WERNER ___RX1 ESE x 10 om Ll Pikes USBO USBO o svisbbv PRIS GND RXO 5 Note 1 In order to meet the requirements of USB standard the 5V input supply must be at least 5 00V Description USBO USBO RX0 RXO TX0 TXO USB1 USB1 RX1 RX1 TX1 TX1 Differential pair works as Data Address Command Bus 5V supply for external devices SB5V is supplied during powerdown to allow 5V SB5V wakeup on USB device activity
35. dB Configuring the De emphasis Control on PEG PEG Sampler Calibrate Auto Enabled Disabled Enable or disable PEG Sampler Calibrate Auto means Disabled for SNB MB DT Enabled for IVB AO BO Swing Control Gen3 Equalization Note1 Gen3 Eq Phase 2 Note1 Reduced Half Full Enabled Disabled Auto Enabled Disabled Perform PEG Swing Control on IVB CO and Later Perform PEG Gen3 Equalization steps Perform PEG Gen3 Equalization phase 2 Gen3 Eq Preset Search Note1 Enabled Disabled Perform PEG Gen3 Preset Search algorithm on IVB Co or Later PEG Link Disabled Enabled Disabled Enable or disable PCle link disable mechanism for additional power saving Fast PEG Init Enabled Disabled Enable or disable Fast PEG Init Some optimization if not PEG devices present in cold boot RxCEM Loop back Enabled Disabled Enable or disable RxCEM Loop back PCle Gen3 RxCTLEp Setting Note1 0 11 12 13 15 Note 1 Only present if Ivy Bridge CPU is used The range of the setting is 0 15 This setting has to be specified based on platform design and following the guideline KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Chipset Aptio Setup Utility Copyright 2012 American Megatrends Inc PEG Gen3 Root Port Preset Value for each Lane Value for Lane 0 Lane 1 Lane 2 Lane 3 Lane 4 Lane 5 Lane 6 Lane 7 Lane 8 Lane 9 Lane 10 Lane
36. i e the BI_DC pair In MDI crossover mode this pair acts as the BI DD pair MDI 3 MDI 3 In MDI mode this is the fourth pair in 1000Base T i e the BI DD pair In MDI crossover mode this pair acts as the BI DC pair Note MDI Media Dependent Interface Ethernet connector 1 ETH1 is mounted together with USB Ports 4 and 5 Ethernet connector 2 ETH2 is mounted together with and above Ethernet connector 3 ETH3 KTQM77 mITX only The pinout of the RJ45 connectors is as follows Type loh lol Note KTQM 77 KTHM76 Users Guide KTD N0850 F IO Area Connectors 5 3 USB Connectors IO Area The KTQM77 board contains two EHCI Enhanced Host Controller Interface and one XHCI Extensible Host Controller Interface The two EHCI controllers EHCI1 and EHCI2 supports up to fourteen USB 2 0 ports allowing data transfers up to 480Mb s The XHCI controller supports four USB 3 0 ports allowing data transfers up to 5Gb s The four USB 3 0 ports are shared with four of the USB 2 0 ports USBO USB3 from the EHCI1 Legacy Keyboard Mouse and wakeup from sleep states are supported Over current detection on all fourteen USB ports is supported The following USB connectors are available in the IO Area USB Port 0 and 1 via EHCI1 XHCI are supplied on the combined USBO USB1 and DPO connector USB Port 2 and 3 via EHCI1 XHCI are supplied on the
37. out of band OOB communication channel that operates below the OS level the channel is independent of the state of the OS present missing corrupted down The communication channel is also independent of the PC s power state however standby power required the presence of a management agent and the state of many hardware components such as hard disk drives and memory AMT is not intended to be used by itself it is intended to be used with a software management application based on 3rd party software If AMT is not required then KTHMG5 KTHM76 might be an alternative or AMT can be disabled in BIOS For more information search for AMT on Intel Homepage PClex2 is only supported on the PClex16 slot if using 3 Generation Core CPU s Ivy Bridge KTQM 77 KTHM76 Users Guide KTD N0850 F System Specification 2 4 System Memory support The KTQM 77 has two DDR3 SODIMM sockets The sockets support the following memory features e 1 5V only 204 pin DDR3 SODIMM with gold plated contacts e Single dual rank unbuffered DDR3 1333 1600MT s PC3 10600 PC3 12800 e From 256MB and up to 2x 8GB up to 2x4GB tested Notes Less than 4GB displayed in System Properties using 32bit OS Shared Video Memory PCI resources is subtracted e SPD timings supported e ECC not supported PGA processors do not support ECC The installed DDR3 SODIMM should support the Serial Presence Detect SPD data structure This allows the BIOS to read an
38. processor the Intel HD Graphics 3000 is supported and equipped with Intel Celeron Processor B810 the Intel HD Graphics is supported The KTQM77 mITX support eDP Embedded DisplayPort directly from processor and both KTQM77 mITX and KTHM76 mITX supports analogue VGA and digital display ports DVI 2x DP LVDS via the Mobile Intel Chipset QM77 or HM76 The Analogue VGA and DVI D are sharing the DVI I connector The PCH supports High bandwidth Digital Content Protection for high definition content playback over digital interfaces The PCH also integrates audio codecs for audio support over DP interfaces Up to three displays any of DPO DP1 DVI D or DVI A LVDS or eDP QM77 only can be activated at the same time and be used to implement independent or cloned display configuration PCle and PCI graphics cards can be used to replace on board graphics or in combination with on board graphics 2 5 1 Intel HD Graphics 4000 Features of the Intel HD Graphics 4000 build into the i3 ib and i7 processors includes e High quality graphics engine supporting o BDirectX11 and OpenGL 4 0 compliant Shader Model 5 0 support Intel amp Clear Video HD Technology Intel amp Quick Sync Video Technology Intel amp Flexible Display Interface Intel amp FDI Core frequency of 650 1150 Turbo MHz Memory Bandwidth up to 21 3 GB s 16 3D Execution Units 1 62 GP s and 2 7 GP S pixel rate eDP and DP outputs Hardware Acceleration CVT HD and QSV Dynamic
39. the Jumper The Jumper has 3 positions Pin 1 2 Pin2 3 default position and not mounted A BCE A Jumper in default position Warning KS Yi Don t leave the jumper in position 1 2 otherwise if power is disconnected the battery will fully deplete within a few weeks J37 pin 1 BIOS version 12 and above J37 Spel ae Description Don t use Board do not boot with jumper in this position Default position Load Default BIOS Settings and erase Password To Load Default BIOS Settings inclusive erasing password 1 Turn off power completely no SB5V Remove the Jumper completely from J37 Turn on power Motherboard beeps fast 20 times and turns off Turn off power Move the Jumper back to position 2 3 default position Turn on power use the Power On Button if required to boot Motherboard might automatically reboot a few times Wait until booting is completed NOahWN BIOS version below 12 Description Load Default BIOS Settings exclusive erasing Password Default position No function To Load Default BIOS Settings exclusive erasing Password and RTC Turn off power completely no SB5V Move the Jumper to pin 1 2 for 10 seconds Move the Jumper back to position 2 3 default position Turn on power use the Power On Button if required to boot Motherboard might automatically reboot a few times Wait until booting is completed Oo RONA KTQM 77 KTHM76 Users Guid
40. the KEK lt Select Screen gt Append an entry to KEK 1 Select Item Key Exchange Key Database DB NOT INSTALLED Enter Select Set DB from File Change Opt Get DB to File F1 General Help Delete the DB F2 Previous Values gt Append an entry to DB F3 Optimized Defaults Key Exchange Key Database DBX NOT INSTALLED F4 Save amp Exit Set DBX from File ESC Exit Get DBX to File Delete the DBX gt Append an entry to DBX Version 2 15 1226 Copyright O 2012 American Megatrends Inc Function Selection Description aem Disabled Force OEM default Secure Boot Keys if System Default Key Provisioning Enabled is in Setup Mode KTQM 77 KTHM76 Users Guide KTD NO850 F BIOS Security 10 5 3 HDD Security Configuration Only visible if entering a device listed below HDD Security Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc HDD Password Description Set HDD User Password Allows Access to set Modify and Clear Advisable to Power Cycle HardDisk User and Master Passwords System after Setting Hard User Password need to be installed for Disk Passwords Enabling Security Master Password can be modified only when successfully unlocked with Master Password in POST HDD PASSWORD CONFIGURATION Security Supported Yes Security Enabled No Security Locked No lt Select Screen Security Frozen No 1 Select Item HDD User Pwd
41. 012 American Megatrends Inc KTQM 77 KTHM76 Users Guide KTD N0850 F Function System Temperature Ext Type note1 Selection Disabled LM75 0x90 OneWire GPIO16 BIOS Advanced Description Fan Cruise Control System Fan Disabled Thermal Speed note2 Disabled Full speed Thermal Regulate according to specified C Speed Regulate according to specified RPM Fan Settings System Fan 30 90 note2 note3 1000 9999 note4 Fan Min limit System Fan 0 note6 Minimum PWM can be used to make sure fan is always active Make sure Min limit Max limit Fan Max limit Maximum PWM can be used to limit the fan System Fan note6 noise Make sure Min limit Max limit a Disabled Disabled Full speed Fan Cruise Control i A Ee CPU Fan Thermal Thermal Regulate according to specified C Speed Speed Regulate according to specified RPM Fan Settings 30 90 note3 CPU Fan 1000 9999 note4 n Minimum PWM can be used to make sure Fan Min limit 0 3 fan is al tive Mak Min limit lt M CPU Fan ssi note6 E always active Make sure Min limi ax Fan Max limit 100 Maximum PWM can be used to limit the fan CPU Fan note7 note6 noise Make sure Min limit Max limit 0 Disabled Watchdog Function 0 255 note8 Enter the service interval in seconds before system will reset Refer to manual how to reload the timer
42. 10000005 Kontron KT 821515 cable kit Kontron KT 821155 cable kit 61201020621 Molex 90635 1103 COM1 2 3 4 Kontron KT 821016 cable kit Kontron KT 821017 cable kit mo a Fines 512 90 10GBB2 Kontron KT 821401 cable kit USB6 7 FRONTPNL Kontron KT 821401 cable kit IEEE1394 0 1 Foxconn HS1105F RNP9 Kontron KT 821040 cable kit AUDIO HEAD Molex 87831 2620 Molex 51110 2651 Kontron KT 821043 cable kit FRONTPNL Pinrex 512 90 24GBB3 Molex 90635 1243 Kontron KT 821042 cable kit FEATURE Foxconn HS5422F Don Connex A05c 44 B G A 1 G USB6 USB7 is located in FRONTPNL connector Depending on application KT 821401 can be used Notes Only one connector will be mentioned for each type of on board connector even though several types with same fit form and function are approved and could be used as alternative Please also notice that standard connectors like DVI DP PCle miniPCle Audio Jack Ethernet and USB is not included in the list The KTHM76 mITX do not support EDP USB6 7 and IEEE1394 0 1 KTQM 77 KTHM76 Users Guide KTD N0850 F 9 System Resources 9 1 Memory Map Address hex System Resources Size hex Description Intel 82802 Firmware Hub Device OxFF000000 OxFFFFFFFF 1000000 MIL EE E E DID PE OxFEEO00000 OxFEEFFFFFE 100000 Motherboard resources OxFED90000 OxFED93FFFE 4000 Mothe
43. 4 J18 is as follows Note 1 The COM1 COM2 COM3 and COM4 5V supply is fused with common 1 1A resettable fuse DB9 adapter cables PN 821016 200mm long and 821017 100mm long are available for implementing standard COM ports on chassis Available cable kit DB9 adapter cables PN 821017 100 mm or PN 821016 200 mm KTQM 77 KTHM76 Users Guide KTD N0850 F Internal Connectors 6 9 Audio Connectors The on board Audio circuit implements 7 1 2 Channel High Definition Audio with UAA Universal Audio Architecture featuring five 24 bit stereo DACs and three 20 bit stereo ADCs The following Audio connectors are available as Internal connectors 6 9 1 CDROM Audio Input CDROM J3 CD ROM audio input may be connected to this connector or it can be used as secondary line in signal PIN Signal Type Note CD Left IA MET CD GND CD GND CD Right Note 1 The definition of which pins are used for the Left and Right channels is not a worldwide accepted standard Some CDROM cable kits expect reverse pin order Signal Description CD Left Left and right CD audio input lines or secondary Line in CD Right CD GND Analogue GND for Left and Right CD This analogue GND is not shorted to the general digital GND on the board 6 9 2 Line2 and Mic2 Line2 and Mic2 are accessible via Feature Connector see Featur
44. 76 Users Guide KTD N0850 F BIOS Chipset 10 3 2 2 DMI Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc DMI Configuration Enable or disable DMI Nei DMI X4 Gen2 DMI Vep Control DMI Vem Control DMI Link ASPM Control DMI Extended Synch Control DMI Gen 2 lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description DMI Vc1 Control Sen Enable or disable DMI Vc1 Disabled Enabled Disabled DMI Vem Control Enabled Enable or disable DMI Vcm Disabled Disabled LOs Enable or disable the control of Active State L1 Power Management on SA side of the DMI Link LOsL1 Enabled Disabled Auto Enable or disable DMI Gen 2 DMI Gen 2 Enabled Auto means Disabled for IVB A0 MB DT and Disabled IVB BO MB Enabled for other CPUs DMI Vcp Control Enable or disable DMI Vcp DMI Link ASPM Control DMI Extended Synch Control Enable DMI Extended Synchronization KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Chipset 10 3 2 3 NB PCle Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc NB PCle Configuration Configure PEGO B0 D1 FO PEGO Not Present Gen1 Gen3 PEGO ASPM Disabled PCIe PEG Bifurcation 1 x16 Enab
45. 76 Users Guide KTD N0850 F BIOS Advanced 10 2 Advanced Aptio Setup Utility Copyright 2012 American Megatrends Inc W Advanced UEC ee PCI PCI X and PCI Express ACPI Settings Settings gt Trusted Computing CPU Configuration SATA Configuration Intel TXT LT Configuration AMT Configuration gt Acoustic Management Configuration USB Configuration SMART Settings Super IO Configuration Voltage Monitor Hardware Health Configuration gt Displayblock Setup lt Select Screen LAN Configuration 1 Select Item Delay Startup Enter Select Serial Port Console Redirection Change Opt CPU PPM Configuration F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Note the submenus Intel TXT LT Configuration and AMT Configuration are only present when using KTQM77 mITX The Advanced main menu contains only submenu selections which will be described in more details on the following pages In order to make a selection of a submenu activated the 1 keys until the requested submenu becomes white color then activate the lt Enter gt KTQM 77 KTHM76 Users Guide KTD N0850 F Page 69 BIOS Advanced 10 2 1 Advanced PCI Subsystem Settings Aptio Setup Utility Copyright 2012 American Megatrends Inc MN Advanced PCI Bus Driv
46. AHCI 1E03 0x0000F0AO0 0x0000F0A3 4 Intel 7 port SATA AHCI 1E03 0x0000F060 0x0000F07F 20 Intel 7 port SATA AHCI 1EO3 0x0000F040 0x0000F05F 20 Intel SMBus 1E22 0x0000F000 0x0000F03F 40 Intel HD Graphics 4000 family 0x0000E000 0x0000EFFF Dm Capellen PCIe Ie joowe 3 EE 0x0000D000 0x0000DFFF 1000 Intel PCIe Root port 4 1E16 0x0000164E 0x0000164F 2 Motherboard resources 0x00001000 0x0000100F 10 Motherboard resources 0x00000F78 0x00000F7F 8 Motherboard resources 0x00000B78 0x00000B7F 8 Motherboard resources 0x00000A00 0x00000A2F 30 Motherboard resources 0x00000778 0x0000077F 8 Motherboard resources 0x00000680 0x0000069F 20 Motherboard resources 0x00000500 0x0000057F Motherboard resources 0x000004D0 0x000004D1 Programmable interrupt controller Motherboard resources 0x00000458 0x0000047F 28 Motherboard resources 0x00000454 0x00000457 4 Motherboard resources 0x00000400 0x00000453 54 Motherboard resources 0x000003F8 0x000003FF 8 COM1 0x000003E8 0x000003EF 0x000003C0 0x000003DF 20 Intel HD Graphics 4000 family 0x000003B0 0x000003BB C Intel HD Graphics 4000 family 0x00000378 0x0000037F 8 Printer port SI 0x000002F8 0x000002FF 3 OP 0x000002E8 0x000002EF 8 COM3 0x00000290 0x0000029F 10 Motherboard resources 0x0000020E 0x0000020F 2 Motherboard resources 0x000000F0
47. Aptio Setup Utility Copyright 2012 American Megatrends Inc Force Boot Setup 1st Boot Port 2nd Boot Device Name 3rd Boot 4th Boot Sata Port 1 This option controls if CSM will be launched Device Name USB N A ST3120827AS lt Select Screen Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Force Boot Selection Disabled Enabled Description 1st Boot 2nd Boot 3rd Boot 4th Boot N A USB SATA SATA Port Device Name Port 0 5 Device Name None ST3120827AS N A N A N A Note 1 1 Boot 2 Boot 3 Boot and 4 Boot have the same set of selections Note 2 Only shown if SATA Port is selected Note 3 Only shown if Device Name is selected Note 4 By key select requested port number Make sure only valid number 0 5 is selected KTQM 77 KTHM76 Users Guide KTD N0850 F i2 Oko wem Tero 10 4 2 CSM parameters Aptio Setup Utility Copyright 2012 American Megatrends Inc Boot option filter Launch PXE OpROM policy Launch Storage OpROM policy Legacy only Launch Video OpROM policy Other PCI device ROM priority UEFI and Legacy Do not launch This option controls if CSM will be launched Legacy only Legacy OpROM lt Select Scre
48. Aptio Setup Utility Copyright 2012 American Megatrends Inc System Agent Bridge Name IvyBridge Check to enable VT d function System Agent Bridge Name 1 5 0 0 on MCH VT d Capability Supported CHAP Device B0 D7 FO Disabled Thermal Device B0 D4 FO Disabled Enable NB CRID Disabled BDAT ACPI Table Support Disabled C State Pre Wake Enabled Graphics Configuration gt DMI Configuration gt NB PCle Configuration lt Select Screen Memory Configuration 1 Select Item Memory Thermal Configuration Enter Select GT Power Management Control Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description VT d Disabled Check to enable VT d function on MCH Enabled CHAP Device B0 D7 F0 pen a Enable or disable SA CHAP Device Thermal Device BO D4 F0 SEE 5 Enable or disable SA Thermal Device Enable NB CRID Enabled Enable or disable NB CRID Workaround Disabled Enabled Disabled BDAT ACPI Table Support Enables support for the BDAT ACPI Table C State Pre Wake Enabled Controls C State Pre Wake feature for ARAT in Note1 Disabled SSKPD 57 Note 1 Only present if Ivy Bridge CPU is used KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Chipset 10 3 2 1 Graphics Configuration Aptio Setup Utility Copyr
49. Assistance Process Note1 Disabled Enabled Trigger CIRA boot USB Configure Note1 Disabled Enabled Enable Disable USB Configure function PET Progress Note1 Disabled Enabled Users can Enable Disable PET Events progress to receive PET events or not AMT CIRA Timeout Note1 Note5 Note4 OEM defined timeout for MPS connection to be established 0 use the default timeout value of 60 seconds 255 MEBX waits until the connection succeeds Watchdog Note2 Disabled Enabled Enable Disable Watchdog Timer OS Timer Note3 0 65535 Note4 Set OS watchdog timer BIOS Timer Note3 0 65535 Note1 Only if Intel AMT Enabled Note4 Note2 This Watchdog function is unsupported Recommendation use Watchdog function present in Hardware Health Configuration menu Note3 Only if Watchdog Enabled Set BIOS Watchdog Timer Note4 To enter number use digit keys and or keys Note5 Only if Active Remote Assistance Process Enabled KTQM 77 KTHM76 Users Guide KTD N0850 F Page 83 BIOS Advanced 10 2 8 Advanced Acoustic Management Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced Acoustic Management Configuration Option to Enable or Disable Automatic Acoustic Management Sata Port 0 ST3120827AS Acoustic Mode Not Available lt Select Screen 1 Select Item
50. B Connector 6 7 EET 43 6 6 2 USB Connector 8 9 USB8 9 10 43 6 6 3 USB Connector 10 11 USB10 11 011 44 6 6 4 USB Connector 12 13 USB12 13 112 maie tinte het Lenta nea d Rau den nana nas 44 6 7 Firewire IEEE1394 connectors U13 J1A EE 45 6 7 1 IEEE1394 connector IEEE1394 0 J14 sssssssesseeeene eene nreen nennen nennen nnns 45 6 7 2 IEEE1394 connector IEEE1394 1 113 dices edic tace ebd c te kak eee bad cac MAL au ake uc edd duda 45 6 8 Serial COM1 COM4 Ports J15 J16 J17 218 enne 46 E Diss RDEIDERT 47 6 9 1 CDROM Audio Input CDROM J3 sssssseseseeeeneenennm nennen nnnm nnne nennen nennen nnns 47 SR ME AN ZAnd MICZ ote e kase taa 47 6 9 3 Audio Header Connector AUDIO HEAD UU 48 6 9 4 Front Panel Connector FRONTPNL J19 QLilLklllo ok koat taka eten aa aa esse eene nennen nennen nnne nnns 49 6 10 Feature Connector FEATURE J30 ssssssessssseeeneenene ooo asse aoatossaaootossaaootossessotossesoosoosesnn 50 6 11 Load Default BIOS Settings Jumper J37 tata ooo ssaaootessaaaosossesoosossesoasooseson 53 6 12 SPL Recover Jumper En E 54 6 13 SPIConnector SPD 153 nie N kof pa a D pa ob ecl ao sote ania 55 6 14 XDP CPU Debug Port for CPU 332 eiie ie aser taco tha cut ska doo sh c th n ha dd kde 56 6 15 XDP PCH Debug Port for Chipset 33 zesse eE E EANO EENE 57 7 Sl
51. C kontron KTQM77 mITX KTQM77 mITX KTHM76 mITX Users Guide KTD N0850 F KTD NO850 F Page 2 Document details Document revision history END XN Comment Jan 2 2014 CPU list revised BIOS part upgraded in according to BIOS Revision Release note KTQM7715 bin Added KTHM76 mITX Jun13th 2013 Minor corrections June 4 2013 Correction to AMT 8 0 Updated CPU list and RAM List Several corrections Added AMT short description Correction to eDP and LVDS text May 27 2013 BIOS Recover text upgraded Added note for PClex2 support BIOS information upgraded to BIOS 14 Page 67 corrected function name Added to BIOS section Mar 6 2013 System Temperature Ext Type and Fan limits Added cable kits Corrected PClex1 signals Note on OS installation via USB Removed 5V tolerance for some GPIO s Jumper J37 info changed 3 3V now 5 tolerance Improved 12V only description Updated CPU list Revision of BIOS section Completed System Resources July 10 2012 Preliminary version Feb 19 2013 Copyright Notice Copyright 2011 KONTRON Technology A S ALL RIGHTS RESERVED No part of this document may be reproduced or transmitted in any form or by any means electronically or mechanically for any purpose without the express written permission of KONTRON Technology A S Trademark Acknowledgement Brand and product names are trademarks or registered trademarks of their resp
52. Console Redirection Disabled lt Select Screen Console Redirection Settings COMA4 Pci Bus0 Dev0 Func0 Disabled Change Opt Console Redirection Port Is Disabled F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit Console Redirection Disabled ESC Exit Console Redirection Settings Serial Port for Out of Band Management Windows Emergency Management Services EMS Version 2 15 1226 Copyright 2012 American Megatrends Inc KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Advanced 10 2 17 1 Console Redirection Settings The Console Redirection Settings menu are only available if related Console Redirection is Enabled A different menu is available for Serial Port for Out of Band Management see next page Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced COMO Console Redirection Settings Bits per second Data Bits Parity Stop Bits Flow Control VT UTF8 Combo Key Support Recorder Mode Resolution 100x31 Legacy OS Redirection Resolution Putty Keypad Redirection After BIOS POST 115200 8 None 1 None Enabled Disabled Disabled 80x24 VT100 Always Enable Emulation ANSI Extended ASCII char set VT100 ASCII char set VT100 Extends VT100 to support color function keys etc VT UTF8 Uses UTF8 encoding to map Unicode chars onto 1 or more bytes lt Select Screen 1 Select
53. Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Selection Description Automatic Acoustic Enabled Option to Enable or Disable Automatic Acoustic Management Disabled Management Note Automatic acoustic management AAM is a method for reducing acoustic emanations in AT Attachment ATA mass storage devices such as ATA hard disk drives and ATAPI optical disc drives AAM is an optional feature set for ATA ATAPI devices when a device supports AAM the acoustic management parameters are adjustable through a software or firmware user interface The ATA ATAPI sub command for setting the level of AAM operation is an 8 bit value from 0 to 255 Most modern drives ship with the vendor defined value of 0x00 in the acoustic management setting This often translates to the max performance value of 254 stated in the standard Values between 128 and 254 0x80 OxFE enable the feature and select most quiet to most performance settings along that range Though hard drive manufacturers may support the whole range of values the settings are allowed to be banded so many values could provide the same acoustic performance KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Advanced 10 2 9 Advanced USB Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc USB Configurati
54. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description Enables or Disables BIOS support for Disabled security device O S will not show Security Enabled Device TCG EFI protocol and INT1A interface will not be available Disabled Enable Disable Security Device NOTE Your TPM State Enabled Computer will reboot during restart in order Hane to change State of the Device Security Device Support None Schedule an Operation for the Security Enable Take Ownership Device NOTE Your Computer will reboot Disable Take Ownership during restart in order to change State of the TPM Clear Device Pending operation Note TPM State and Pending operation are only visible if Security Device Support is Enabled followed by Save and Exit KTQM 77 KTHM76 Users Guide KTD N0850 F 10 2 4 Advanced CPU Configuration BIOS Advanced Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced CPU Configuration Intel Core 15 3610ME CPU Q CPU Signature Microcode Patch Max CPU Speed Min CPU Speed CPU Speed Processor Cores Intel HT Technology Intel VT x Technology Intel SMX Technology 64 bit L1 Data Cache L1 Code Cache L2 Cache L3 Cache Active Processor Cores Limit CPUID Maximum Execute Disable Bit Intel Virtualization Technology 2 70G
55. G Explosionsfara vid felaktigt batteribyte Anvand samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren Kassera anvant batteri enligt fabrikantens instruktion VORSICHT Explosionsgefahr bei unsachgemaRem Austausch der Batterie Ersatz nur durch den selben oder einen vom Hersteller empfohlenen gleichwertigen Typ Entsorgung gebrauchter Batterien nach Angaben des Herstellers ADVARSEL Eksplosjonsfare ved feilaktig skifte av batteri Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten Brukte batterier kasseres i henhold til fabrikantens instruksjoner VAROITUS Paristo voi rajahtaa jos se on virheellisesti asennettu Vaihda paristo ainoastaan laltevalmistajan suosittelemaan tyyppiin Havita kaytetty paristo valmistajan ohjeiden mukaisesti KTQM 77 KTHM76 Users Guide KTD NO850 F System Specification 2 System Specification 2 1 Component main data The table below summarizes the features of the KTQM77 mITX embedded motherboard Form factor KTOM77 mITX and KTHM76 mITX minilTX 170 18 mm by 170 18 mm Processor Support 2 and 3 Generation Intel Core Sandy Bridge M and Ivy Bridge M respectively and Intel amp Celeron amp processors via Socket G2 rPGA 988B ZIF Socket e Intel amp Core i7 e Intel Core i5 e Intel amp Core i3 e Intel Celeron B810 Up to 1333MHz system bus and 2 3 4 6MB internal cache
56. GT Info RC6 Deep RC6 GT Overclocking Support Check to enable render GT2 0x166 standby support Enabled Disabled lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function RC6 Render Standby Selection Enabled Disabled Description Check to enable render standby support RC6 Deep RC6 Enabled Disabled Check to enable Deep RC6 RC6 support GT Overclocking Support Enabled Disabled Enable or disable GT Overclocking Support KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Boot 10 4 Boot Aptio Setup Utility Copyright 2012 American Megatrends Inc Mam Advanced Chipset boot Security Save amp Exit Boot Configuration Number of seconds to wait for setup activation key Bootup NumLock State On 65535 OXFFFF means indefinite waiting Quit Boot Disabled Fast Boot Disabled CSM16 Module Version 07 69 GateA20 Active Upon Request Option ROM Message Force BIOS INT19 Trap Response Immediate Driver Option Priorities lt Select Screen 1 Select Item Boot Option Priorities Enter Select Boot Option 1 P1 ST3120827AS f Change Opt gt Force Boot Setup F1 General Help gt CSM parameters F2 Previous Values F3 Optimized Defaults F4 S
57. Hz 306a8 10 2700 MHz 1200 MHz 2700 MHz 2 Supported Supported Supported Supported 32 kB x2 32 kB x2 256 kB x 2 3072 kB All Disabled Enabled Disabled Enabled for Windows XP and Linux OS optimized for Hyper Threading Technology and Disabled for other OS OS not optimized for Hyper Threading Technology When Disabled only one thread per enabled core is enabled Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Hyper threading Note1 Selection Disabled Enabled Description Enabled for Windows XP and Linux OS optimized for Hyper Threading Technology and Disabled for other OS OS not optimized for Hyper Threading Technology When Disabled only one thread per enabled core is enabled Active Processor Cores All 1 Number of cores to enable in each processor package Limit CPUID Maximum Disabled Enabled Disabled for Windows XP Execute Disable Bit Disabled Enabled XD can prevent certain classes of malicious buffer overflow attacks when combined with supporting OS Windows Server 2003 SP1 Windows XP SP2 SuSE Linux 9 2 RedHat Enterprise 3 Update 3 Intel Virtualization Technology Disabled Enabled Note1 Not present when using Intel Celeron B810 When ena
58. I een ie ab ay koton e kodak eya Do bl koi ye AD dyak a a aa good ap on ka n As adan kan 130 10 4 1 Force Boot Setup ENNEN EEN EEN EEN 132 10 4 2 CSM parameters niiina aaa 133 10 5 Security EE 134 10 5 1 Image EX utiOniPOMEY atitid etos ine dee rai na aede ae 135 10 5 2 Key Management uk EEN 136 10 5 3 HDD Security Configuration ssssssessssseene nennen enne nennen nne n nennen nnne nnns 137 106 dap 138 11 AMEBIOS e 139 pagis go c 140 KTQM 77 KTHM76 Users Guide KTD N0850 F Introduction Introduction This manual describes the KTQM77 family consisting of the KTQM77 mITX and the KTHM76 mITX boards made by KONTRON Technology A S In this Users Guide the boards will in general also be denoted KTQM77 and KTHM76 and if a subject is not depending on exact board type then both types of board will be denoted KTQM77 The KTQM77 and KTHM76 boards are based on the QM77 and HM76 chipset respectively and support 3 generation Intel i7 i5 i3 2Core and 4Core mobile processors See Processor Support Table for more specific details The KTQMT77 family consist on members having same form factors and the same functionality except for the functions listed in the table below IEEE PCle x16 KTQM 77 variants LAN RAID AMT eDP r 1394a Bifurcation 4x USB3 0 2 0 KTQM77 mITX 0 1 5 10 AMT8 0
59. Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc KTQM 77 KTHM76 Users Guide KTD N0850 F Function Page 102 Selection BIOS Advanced Description VT100 Emulation ANSI Extended ASCII char set VT100 VT100 ASCII char set VT100 Extends Terminal Type VT UTF8 VT100 to support color function keys etc VT 3 UTF8 Uses UTF8 encoding to map Unicode ANSI chars onto 1 or more bytes 9600 19200 Select serial port transmission speed The Bits per second 38400 speed must be matched on the other side Long 57600 or noisy lines may require lower speeds 115200 Data Bits 7 8 Data Bits A parity bit can be sent with the data bits to detect some transmission errors None Even parity bit is O if the num of 1 s in the data Even bits is even Parity Odd Odd parity bit is O if the num of 1 s in the data Mark bits is odd Space Mark parity bit is always 1 Space parity bit is always O Mark Space do not allow error detection Stop bits indicate the end of a serial data 1 packet A start bit indicates the beginning Stop Bits 2 The standard setting is 1 stop bit Communication with slow devices may require more than 1 stop bit Flow control can prevent data loss from buffer overflow When sending data if the receiving None buffers are full a stop sign
60. OOK4 HOOK5 5V PWR FA HOOK6 ER HOOK7 500R 500R by 2x1K in parallel 19 GND PWR E TDO 51R PAN TRST 51R 22 TDI 51R 23 TMS 51R 24 NC NC R 25 GND PWR E 26 TCKO 51R KTQM 77 KTHM76 Users Guide KTD NO850 F Page 57 Internal Connectors 6 15 XDP PCH Debug Port for Chipset J33 The XDP PCH Intel Debug Port for Chipset connector is not mounted and not supported XDP PCH connector layout pads is located on the backside of PCB below J35 connector on mITX version and is prepared for the Molex 52435 267 1 or 52435 2672 Pin Signal Description Type Pull Up Down OMAN OO C0 h RSMRST Connected to HOOK6 HOOK1 PWRBTN HOOK2 HOOK3 HOOK4 HOOKS 5V Connected to HOOK1 RESET 500R 500R by 2x1K in parallel 210R 100R 210R 100R 210R 100R KTQM 77 KTHM76 Users Guide KTD NO850 F Page 58 Slot Connectors 7 Slot Connectors PCle miniPCle PCI 7 1 PCle Connectors All members of the KTQM77 family supports one x16 16 lane PCI Express port one x1 PCI Express port and two miniPCI Express ports The 16 lane x16 PCI Express PCle 2 0 and PCle 3 0 port can be used for external PCI Express cards inclusive graphics card It is located nearest the CPU Maximum theoretical bandwidth using 16 lanes is 16 GB s PCle x1 PCle x2 PCle x4 PCle x8 and PCle x16 are supported however PCle x2 is o
61. P 400 mm KTQM 77 KTHM76 Users Guide KTD N0850 F Internal Connectors GPIO in more details The GPIO s are controlled via the ITE IT8516F Embedded Controller Each GPIO has 100pF to ground clamping Diode to 3V3 and has multiplexed functionality Some pins can be DAC Digital to Analogue Converter output PWM Pulse Width Modulated signal output ADC Analogue to Digital Converter input TMRI Timer Counter Input WUI Wake Up Input RI Ring Indicator Input or some special function IT8516F pin name Description DACO GPJO AO IOS DAC1 GPJ1 AO IOS GPIO2 DAC2 GPJ2 AO IOS GPIO3 DAC3 GPJ3 AO IOS GPIO4 PWM2 GPA2 O8 10S GPIO5 PWM3 GPA3 O8 10S GPIO6 PWM4 GPA4 O8 10S GPIO7 PWM5 GPAS O8 IOS GPIO8 ADCO GPIO ANIS GPIO9 ADC1 GPI1 ANIS GPIO10 ADC2 GPI2 ANIS GPIO11 ADC3 GPI3 ANIS GPIO12 ADC4 WUI28 GP14 AI IS IS GPIO13 RITZ WUIO GPDO IS IS IOS GPIO14 RI2ZANUI GPD1 IS IS IOS GPIO15 TMRIO WUI2 GPC4 IS IS IOS GPIO16 TMRI1 WUI3 GPC6 IS IS IOS GPIO17 L80HLAT BAO WUI24 GPEO O4 O4 IS IOS Feature Break out board PN 820978 Feature BOB Break Out Board KTQM 77 KTHM76 Users Guide KTD NO850 F Page 53 Internal Connectors 6 11 Load Default BIOS Settings Jumper J37 The Load Default BIOS Settings Jumper J37 can be used to recover from incorrect BIOS settings As an example incorrect BIOS settings coursing no display to turn on can be erased by
62. TSC_433 PAL B PAL G PAL D PAL H PAL I PAL M PAL N SECAM L TV1 Standard SECAM B SUDO to configure a SECAM D SECAM G SECAM H SECAM K HDTV STD SMPTE 240M 1080159 HDTV STD SMPTE 240M 1080i60 HDTV STD SMPTE 295M 1080150 HDTV STD SMPTE 295M 1080p50 HDTV STD SMPTE 296M 720p50 HDTV STD SMPTE 296M 720p60 HDTV STD CEAEIA 7702A 480p60 HDTV STD CEAEIA 7702A 480i60 VBIOS Default NTSC M NTSC M J NTSC 433 PAL B PAL G PAL D PAL H PAL PAL M PAL N cce E Select the ability to configure a elec ea TV2 Standard SECAM B TV Minor Format SECAM D SECAM G SECAM H SECAM K HDTV STD SMPTE 240M 1080i59 HDTV STD SMPTE 240M 1080i60 HDTV STD SMPTE 295M 1080150 HDTV STD SMPTE 295M 1080p50 HDTV STD SMPTE 296M 720p50 HDTV STD SMPTE 296M 720p60 HDTV STD CEAEIA 7702A 480p60 HDTV STD CEAEIA 7702A 480160 KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Chipset Function Selection Description Valid only for ACPI Legacy ALS Support through the IGD INT10 ALS Support TE d function SCPI ALS support through an ACPI ALS driver Select the Active LFP Configuration No LVDS No LVDS VBIOS does not enable LVDS Int LVDS Int LVDS VBIOS enables LVDS driver by Geer SC Se eee VEER les LVDS driver b eDP Port A S enables driver by SEED SDVO encoder g on eDP Port A LFP driven by Internal DisplayPort encoder from Port A Panel Color Depth Select the LFP Panel Color Depth KTQM 77 KTHM
63. The KTQMT77 has an integrated SATA Host controller PCH in the QM77 chipset that supports independent DMA operation on six ports One device can be installed on each port for a maximum of six SATA devices A point to point interface SATA cable is used for host to device connections Data transfer rates of up to 6 0Gb s typically 600MB s on SATAO and SATA1 and 3 0Gb s typically 300MB s on SATA2 SATA3 SATA4 and SATA5 SATA2 is shared with mPCle0 Note Before installing OS on a SATA drive make sure the drive is not a former member of a RAID system If so some hidden data on the disk has to be erased To do this connect two SATA drives and select RAID in BIOS Save settings and select Ctrl I while booting to enter the RAID setup menu Now the hidden RAID data will be erased from the selected SATA drive The SATA controller supports RAID Redundant Array of Independent Drives based on a firmware system KTQM77 mITX only 2 to 6 drive RAID 0 data striping 2 drive RAID 1 data mirroring 3 to 6 drive RAID 5 block level striping with parity 4 drive RAID 10 data striping and mirroring 2 to 6 drive matrix RAID parts of a single drive can be assigned to different RAIDs AHCI Advanced Host Controller Interface NCQ Native Command Queuing NCQ is for faster data access Hot Swap Intel Rapid Recover Technology 2 256TB volume Data volumes only Capacity expansion TRIM in Windows 7 in AHCI and RAID mode for drives not part of a
64. Thermal Load 111W 111W Note Listed power consumptions are inclusive 15 25W for PSU HDD and DVD More detailed Static Power Consumption TBD On the following pages the power consumption of different boards in different configurations are listed For each configuration the power consumptions result are listed in 5 tables 1 DOS idle mean 2 Windows7 Running 3DMARK 2005 amp BiT 6 mean 3 SO mean 4 S3 mean 5 S5 mean Note some S5 measurements have been carried out in two sub modes M3 and Moff Only S5 M3 mode maintains power to the circuits used for AMT and waking up the system via LAN Keyboard and USB while both S5 M3 and S5 Moff maintain power to RTC Power Button In circuit and CMOS data KTQM 77 KTHM76 Users Guide KTD N0850 F System Specification The principal test system and test equipment used TBD 1 Tektronix TDS5104B 2 Tektronix TCPA300 3 Tektronix TCP312 ATX supplies 4 Fluke 289 Current 5 Fluke 179 Probe Tektronix TDS5104B 6 ATX rail switch Note Power consumption of PSU power loss Monitor and HDD are not included The following four configurations a d have been tested TBD a Low Power Setup KTQM77 mITX ATX 12V PSU b Low Power Setup KTQM77 mITX 12V only PSU Standard system configuration equipped with PClex1 card Internal graphics 2x SATA disks Intel i5 CPU 1x SODIMM 1GB Modules Monitor Keyboard amp Mouse 1x 1 4GB USB Stick 12V active c
65. Users Guide KTD NO850 F System Specification Intel i3 i5 amp i7 3 Generation Mobile processors support Intel HD Graphics 4000 Intel i3 ib amp i7 2 Generation Mobile processor supports Intel HD Graphics 3000 Intel Celeron Processor B810 supports Intel HD Graphics eDP Embedded DisplayPort directly from processor KTQM 7 only Analogue VGA and digital display ports DVI 2x DP LVDS via the Mobile Intel QM77 Chipset VGA analogue panel via DVI I sharing DVI I connector with DVI D DVI D sharing DVI I connector with analogue VGA 2x DP DisplayPorts comply with DisplayPort 1 2 specification LVDS panel support up to 24 bit 2 pixels clock and 1920x1200 HDMI panel support via DP to HDMI Adapter Converter Second VGA panel support via DP to VGA Adapter Converter Second DVI panel support via DP to DVI Adapter Converter Dual independent pipes for Mirror and Dual independent display support exception is combination LVDS and eDP Triple independent pipes Intel HD Graphics 4000 only for triple independent or cloned displays are supported from OS Any 3 displays via DPO DP1 DVI D or DVI A LVDS or eDP can be used but only active DP to DVI HDMI converters can be used UO Control Peripheral interfaces Via ITE IT8516E Embedded Controller and Nuvoton W83627DHG UO Controller both via LPC Bus interface Two USB 2 0 ports on I O area Four USB 3 0 USB 2 0 on I O area Eight USB 2 0 ports on internal pin
66. V3 19 LINE2 R AGND 21 AGND MIC2 L 23 MIC2 R Note 1 USB 6 7 only supported by KTQM77 mITX Description 5V supply for external devices SB5V is supplied during powerdown to allow wakeup on USB device activity Protected by resettable 1 1A fuse covering both USB ports USB6 USB6 Universal Serial Bus Port 6 Differentials Bus Data Address Command Bus USB7 USB7 Universal Serial Bus Port 7 Differentials Bus Data Address Command Bus 45V Maximum load is 1A or 2A per pin if using IDC connector flat cable or crimp terminals respectively SATA LED SATA Activity LED active low signal 3V3 output when passive SUS LED Suspend Mode LED active high signal Output 3 3V via 4700 Power Button In Toggle this signal low to start the ATX BTX PSU and boot the board USB6 7_5V PWRBTN_IN Reset Input When pulled low for a minimum 16ms the reset process will be initiated E The reset process continues even though the Reset Input is kept low LINE2 Line2 is second stereo Line signals MIC2 MIC2 is second stereo microphone input SB3V3 Standby 3 3V voltage Analogue Ground for Audio Note In order to meet the requirements of USB standard the 5V input supply must be at least 5 00V Available cable kit PN 821042 Cable Front Panel Open End 300 mm KTQM 77 KTHM76 Users Guide KTD NO850 F Pa
67. Video Memory Technology DVMT support up to 1720 MB Oo oo Oo Oo oo oO e eDP Embedded DisplayPort on QM77 Not in combination with LVDS e DPO and DP1 o 24 30 bit colours in WQXGA 2560x1600 pixels and HDCP o DisplayPort standard 1 2 2 5 2 Intel HD Graphics 3000 Features of the Intel HD Graphics 3000 build into the i3 ib and i7 processors includes e High quality graphics engine supporting o DirectX10 1 and OpenGL 3 0 compliant Shader Model 4 1 support Intel Clear Video HD Technology Intel Quick Sync Video Technology Intel amp Flexible Display Interface Intel FDI Core frequency of 350 1300 Turbo MHz Memory Bandwidth up to 21 3 GB s 12 3D Execution Units 1 62 GP s and 2 7 GP S pixel rate eDP and DP outputs Hardware Acceleration full MPEG2 full VC 1 and full AVC Dynamic Video Memory Technology DVMT support up to 1720 MB 0000000000 e eDP Embedded DisplayPort on QM77 Not in combination with LVDS e DPO and DP1 o 24 30 bit colours in WQXGA 2560x1600 pixels and HDCP o DisplayPort standard 1 1a KTQM 77 KTHM76 Users Guide KTD N0850 F System Specification 2 5 3 LVDS and DVI e LVDS panel Support optional 18 24 bit colours in up to WUXGA 1920x1200 60 Hz and SPWG VESA colour coding OpenLDI JEIDA colour coding is 18 bit with or without Dithering Not in combination with eDP QM77 only e DVI I Digital Visual Interface o Either DVI A or DVI D can be used via DVI I conn
68. act your Distributor or FAE See also chapter System Memory Support 3 Install the processor The CPU is keyed and will only mount in the CPU socket in one way Use suitable screwdriver to open close the CPU socket Refer to supported processor overview for details 4 Cooler Installation Use heat paste or adhesive pads between CPU and cooler and connect the Fan electrically to the FAN CPU connector 5 Connecting Interfaces Insert all external cables for hard disk keyboard etc A monitor must be connected in order to be able change BIOS settings 6 Connect and turn on PSU Connect PSU to the board by the ATX BTXPWR and the 4 pin ATX 12V connectors For the KTQM 77 mITX alternatively use only the 4 pin ATX 12V connector if single voltage operation 12V 5 is requested 7 Power Button Depending on BIOS setting the PWRBTN IN must be toggled to start the Power supply this is done by shorting pins 16 PWRBTN IN and pin 18 GND on the FRONTPNL connector see Connector description A normally open switch can be connected via the FRONTPNL connector 8 BIOS Setup Enter the BIOS setup by pressing the Del key during boot up Enter Exit Menu and Load Optimal Defaults Refer to the BIOS Configuration Setup section of this manual for details on BIOS setup 9 Mounting the board to chassis Warning When mounting the board to chassis etc please notice that the board contains components on both sides of the PCB which c
69. aded automatically when loading Restore Default see Save amp Exit menu In this Users Guide the default settings are indicated by bold Please notice that Restore User Defaults might have different set of default values 10 1 Main Aptio Setup Utility Copyright O 2012 American Megatrends Inc Advanced Chipset Boot Security Save amp Exit BIOS Information Set the Date Use Tab to BIOS Vendor American Megatrends switch between Date elements Core Version 4 6 5 3 Compliancy UEFI 2 3 PI 1 2 BIOS Version 15 Build Date and Time 12 19 2013 07 42 40 EC Firmware Version V1 21 07 05 18 Board Information Product Name KTQM77 mITX PCB ID 00 Serial 01092087 Part 64800000 Boot Count 452 lt Select Screen Mon 30 2013 T Select Item System Time Enter Select Change Opt Access Level imistrator F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Blue text for settings that can be changed White text for actual setting to be changed via the control keys Black text for settings that cannot be changed via control keys Note Product Name is KTHM76 mITX or KTQM77 mITX depending on actual board type The following table describes the changeable settings Feature Options Description System Date MM DD YYYY Set the system date System Time HH MM SS Set the system time KTQM 77 KTHM
70. al can be sent to Flow Control stop the data flow Once the buffers are empty Hardware RTS CTS a start signal can be sent to re start the flow Hardware flow control uses two wires to send start stop signals VT UTF8 Combo Key Disabled Enable VT UTF8 Combination Key Support for Support Enabled ANSI VT100 terminals Recordar Mede Disabled On this mode enabled only text will be send Enabled This is to capture Terminal data Disabled Enables or disables extended terminal Resolution 100x31 Enabled man Legacy OS Redirection 80x24 On Legacy OS the Number of Rows and Resolution 80x25 Columns supported redirection VT100 LINUX XTERMR Putty Keypad SCO 9 Select FunctionKey and KeyPad on Putty ESCN VT400 Redirection After BIOS POST Always Enable BootLoader The settings specify if BootLoader is selected than Legacy console redirection is disabled before booting to Legacy OS Default value is Always Enable which means Legacy console Redirection is enabled for Legacy OS KTQM 77 KTHM 6 Users Guide KTD N0850 F Page 103 BIOS Advanced When Serial Port for Out of Band Management Windows Emergency Management Services EMS gt Console Redirection is enabled Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced Terminal Type Bits per second Flow Control Data Bits Parity Stop Bits VT UTF8 115200 None 8 None 1 Microsoft Windows Emergency M
71. ally disabled Azalia Internal HDMI codec Enabled Enabled Azalia will be Azalia HDMI codec Port B Enabled unconditionally enabled Azalia HDMI codec Port C Enabled Auto Azalia will be enabled if Azalia HDMI codec Port D Enabled present disabled otherwise lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description Control Detection of the Azalia device Disabled Disabled Azalia unconditionally disabled Enabled Enabled Azalia unconditionally enabled Auto Auto Azalia enabled if present disabled otherwise Auto The insertions of audio jacks are auto Audio Jack Sensing Disabled determined Note1 Auto Disabled Driver assumes that all jacks are inserted useful when using the Audio pinrow Azalia Internal HDMI codec Disabled Enable or disable internal HDMI codec for Note1 Enabled Azalia Azalia HDMI codec PortB Azalia HDMI codec PortC Disabled Enable or disable internal HDMI codec for Azalia HDMI codec PortD Enabled Azalia Note2 Note1 Only visible if Azalia is not Disabled Note2 Only visible if Azalia is not Disabled and Azalia Internal HDMI codec is Enabled KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Chipset 10 3 2 System Agent SA Configuration
72. an easily be damaged if board is handled without reasonable care A damaged component can result in malfunction or no function at all When fixing the Motherboard on a chassis it is recommended using screws with integrated washer and having diameter of 7mm Note Do not use washers with teeth as they can damage the PCB and may cause short circuits KTQM 77 KTHM76 Users Guide KTD N0850 F Page 9 Installation procedure 1 2 Requirement according to IEC60950 Users of KTQM77 should take care when designing chassis interface connectors in order to fulfil the IEC60950 standard When an interface connector has a VCC or other power pin which is directly connected to a power plane like the VCC plane To protect the external power lines of the peripheral devices the customer has to take care about e That the wires have suitable rating to withstand the maximum available power e That the enclosure of the peripheral device fulfils the fire protecting requirements of IEC60950 Lithium Battery precautions CAUTION Danger of explosion if battery is incorrectly replaced Replace only with same or equivalent type recommended by manufacturer Dispose of used batteries according to the manufacturer s instructions ADVARSEL Lithiumbatteri Eksplosionsfare ved fejlagtig handtering Udskiftning ma kun ske med batteri af samme fabrikat og type Lev r det brugte batter tilbage til leveranderen VARNIN
73. anagement Services EMS allows for remote management of a Windows Server OS through a serial port lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Out of Band Mgmt Port Selection COMO COM1 COM2 COM3 COMA Pci Bus Dev Func0 Disabled Description Microsoft Windows Emergency Management Services EMS allows for remote management of a Windows Server OS through a serial port Terminal Type VT100 VT100 VT UTF8 ANSI VT UTF8 is the preferred terminal type for out of band management The next best choice is VT100 and then VT100 See above in Console Redirection Settings page for more Help with Terminal Type Emulation Bits per second 9600 19200 57600 115200 Select serial port transmission speed The speed must be matched on the other side Long or noisy lines may require lower speeds Flow Control None Hardware RTS CTS Software Xon Xoff Flow control can prevent data loss from buffer overflow When sending data if the receiving buffers are full a stop signal can be sent to stop the data flow Once the buffers are empty a start signal can be sent to re start the flow Hardware flow control uses two wires to send start stop signals KTQM 77 KTHM76 Users Guide
74. ards ATX BTX Power Connector J43 Note Type Signal PIN Signal Type Note PWR 3V3 12 24 GND PWR PWR 12V eS 5V PWR PWR 12V BP 5V PWR PWR SB5V BEERA 5V PWR l P_OK 20 5V PWR 1 PWR GND 7 19 GND PWR PWR 5V 6 18 GND PWR PWR GND 5b 17 GND PWR PWR 5V 16 PSON OC PWR GND 15 GND PWR PWR 3V3 12V PWR PWR 3V3 3V3 PWR Note 1 5V supply is not used on board See chapter Power Consumption regarding input tolerances on 3 3V 5V SB5V 12 and 12V also refer to ATX specification version 2 2 ATX 12V 4pin Power Connector J42 Note Type Signal PIN Signal Type Note PWR GND ER PWR GND MENE Note 1 Use of the 4 pin ATX 12V Power Connector is required for operation of KTQM77 Description P_OK is a power good signal and should be asserted high by the power supply to indicate that the 5VDC and 3 3VDC outputs are above the undervoltage thresholds of the power supply When this signal is asserted high there should be sufficient energy stored by the converter to guarantee continuous power operation within specification Conversely when the output voltages fall below the undervoltage threshold or when mains power has been removed for a time sufficiently long so that power supply operation is no longer guaranteed P_OK should be de asserted to a low state The recommended electrical and timing characteristics of th
75. ave amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Note When pressing lt F7 gt while booting it is possible manually to select boot device KTQM 77 KTHM 6 Users Guide KTD N0850 F Function Selection IONE Tero Description Number of seconds to wait for setup Setup Prompt Timeout 1 2 65535 Note activation key 65535 OxFFFF means indefinite waiting Bootup NumLock State oe Select the Keyboard Numlock state isabl Quit Boot ee Enables or disables Quiet Boot option Enabled Enables or disables boot with initialization of Feci Boa Disabled a minimal set of devices required to launch Enabled active boot option Has no effect for BBS boot options Upon Request GA20 can be disabled Upon Request using BIOS services GateA20 Active Always do not allow disabling GA20 this Always option is useful when any RT code is executed above 1MB Option ROM Message Force BIOS Keep Current Set display mode for Option ROM INT19 Trap Response Immediate Postponed BIOS reaction on INT19 trapping by Option ROM Immediate execute the trap right away Postponed execute the trap during legacy boot Boot Option 1 list of bootable devices Note To enter number use digit keys and or keys Sets the system boot order KTQM 77 KTHM76 Users Guide KTD N0850 F i2 Oko wem Tero 10 4 1 Force Boot Setup
76. bernation ACPI Sleep State Enabled Enables or Disables BIOS APCI Auto Configuration Both S1 and S3 ava lt Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Enable ACPI Auto Configuration Selection Disabled Enabled Description Enables or Disables BIOS APCI Auto Configuration Enable Hibernation Disabled Enabled Enables or Disables System ability to Hibernate OS S4 Sleep State This option may be not effective with some OS ACPI Sleep State Suspend Disabled 1 only CPU Stop Clock S3 only Suspend to RAM Both S1 and S3 available For OS to choose from Select ACPI sleep state the system will enter when the SUSPEND button is pressed KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Advanced 10 2 3 Advanced Trusted Computing Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced Configuration Enables or Disables BIOS support for security device O S TPM State Enabled will not show Security Device Pending operation None TCG EFI protocol and INT1A interface will not be available Current Status Information TPM Enabled Status Disabled TPM Active Status Deactivated TPM Owner Status Unowned lt Select Screen Change Opt
77. bled a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Advanced Notes Intel HT Technology Hyper Threading Technology is a performance feature which allows one core on the processor to appear like 2 cores to the operating system This doubles the execution resources available to the O S which potentially increases the performance of your overall system Intel VT x Technology Virtualization Technology Previously codenamed Vanderpool VT x represents Intel s technology for virtualization on the x86 platform In order to support Virtualization Technology the CPU must support VT x and the BIOS setting Intel Virtualization Technology must be enabled Intel SMX Technology Safer Mode Extensions Technology is a part of the Trusted Execution Technology KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Advanced 10 2 5 Advanced SATA Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced Enable or Disable SATA Device ACHI Gen3 SATA Mode Selection SATA Controller Speed gt Software Feature Mask Configuration Serial ATA Port 0 Software Preserve Port 0 Hot Plug External SATA SATA Device Type Spin Up Device Serial ATA Port 1 Software Preserve Port 1 Hot Plug External SATA SATA Device Type ST3120827AS 120 NOT SUPPORTED Enabled Disabled Disabled
78. boot To disable ETH1 ME Subsystem must be as well Enabled Enable or disable integrated LAN to wake the Wake on LAN Disabl system The Wake On LAN cannot be disabled isabled if ME is on at Sx state Disabled ETH2 Configuration Enabled Control of Ethernet Devices and PXE boot To Upper disable ETH2 ME Subsystem must be as well With PXE boot ETH fi i e Control of Eth t Devi d PXE boot T 3 Configuration Enabled ontrol o ernet Devices an oot To Lower disable ETH3 ME Subsystem must be as well With PXE boot KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Advanced 10 2 15 1 Network Stack Aptio Setup Utility Copyright O 2012 American Megatrends Inc NNA avan Wl Enable Disable UEFI network Ipv4 PXE Support Enable stack Ipv6 PXE Support Enable Ipv6 Delay Time 0 lt Select Screen Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description Di le Link Network stack lable Lin Enable Disable UEFI network stack Enabled Ipv4 PXE Support Enabled Enable Ipv4 PXE Boot Support If disabled IPV4 Note1 Disabled PXE boot option will not be created Ipv6 PXE Support Enabled Enable Ipv6 PXE Boot Support If disabled IPV6 Note1 Disabled PXE boot option will not be created p 0 15 Note2 Set Seconds of Delay B
79. cluding Electrical Business Equipment Product Category CCN NWGQ2 NWGQ8 File number E194252 Theoretical MTBF 269 335 132 342 hours 40 C 60 C for the KTQM77 mITX gt 269 335 gt 132 342 hours 40 C 60 C for the KTHM76 mITX Restriction of Hazardous Substances RoHS The KTQM77 mITX and KTHM76 mITX are RoHS compliant Capacitor utilization No Tantalum capacitors on board Only Japanese brand Solid capacitors rated for 100 C used on board KTQM 77 KTHM76 Users Guide KTD NO850 F System Specification 2 2 System overview The block diagram below shows the architecture and main components of the KTQM77 The key component on the board is the Intel QM77 Panther Point Mobile Express Chipset Some components PCI slots are optional depending on board type DDR3 3L up to 1600 MHz 1x16 lanes or 2x8 PCI Express 3 0 Graphics Intel Core processors DDR3 Processor 1x8 amp 1x4 lanes up to 1600 MHz Graphics PCI Express 3 0 1x4 lanes for Thunderbolt Intel High EDI i aiad Definition Audio 5 Gb s 8 PCI Express 2 0 each x1 up to BSR Reg n wn Intel QM77 6 Gb s Port Disable Express Intel Rapid Storage Chipset Technology w RAID 3 Independent Display Support 4xUSB 3 0 Ports 10xUSB 2 0 Ports Dual EHCI USB Port Disable Intel Integrated 10 100 1000 MAC Pde x1 sMBus Responsiveness Technologies SPI Intel ME 8 x
80. ct with a similar product Replacement Product or parts may include remanufactured or refurbished parts or components The warranty does not cover 1 Damage deterioration or malfunction resulting from Accident misuse neglect fire water lightning or other acts of nature unauthorized product modification or failure to follow instructions supplied with the product Repair or attempted repair by anyone not authorized by KONTRON Technology Causes external to the product such as electric power fluctuations or failure Normal wear and tear Any other causes which does not relate to a product defect 2 Removal installation and set up service charges gt moow Exclusion of damages KONTRON TECHNOLOGY LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT KONTRON TECHNOLOGY SHALL NOT BE LIABLE FOR 1 DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT DAMAGES BASED UPON INCONVENIENCE LOSS OF USE OF THE PRODUCT LOSS OF TIME LOSS OF PROFITS LOSS OF BUSINESS OPPORTUNITY LOSS OF GOODWILL INTERFERENCE WITH BUSINESS RELATIONSHIPS OR OTHER COMMERCIAL LOSS EVEN IF ADVISED OF THEIR POSSIBILITY OF SUCH DAMAGES 2 ANY OTHER DAMAGES WHETHER INCIDENTAL CONSEQUENTIAL OR OTHERWISE 3 ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY KTQM 77 KTHM76 Users Guide KTD N0850 F Page 4 Contents Contents li os en ee ee 7 1 Installation procedure cn
81. d Power Interface Plug amp Play o Suspend S1 mode o Suspend To Ram S3 mode o Suspend To Disk S4 mode Always On BIOS power setting RAID Support RAID modes 0 1 5 and 10 KTQM77 mITX only Operating Systems Support WinXP 32b 64b Vista 32b 64b Windows 7 32b 64b Linux VxWorks Windows Server 2003 r2 32b 64b Windows Server 2008 r2 32b 64b WES7 32b 64b Out Of The Box installation test only KTQM 77 KTHM76 Users Guide KTD NO850 F System Specification Environmental Operating Conditions 0 C 60 C operating temperature forced cooling It is the customer s responsibility to provide sufficient airflow around each of the components to keep them within allowed temperature range 10 90 relative humidity non condensing Storage 20 C 70 C lower limit of storage temperature is defined by specification restriction of on board CR2032 battery Board with battery has been verified for storage temperature down to 40 C by Kontron 5 95 relative humidity non condensing Electro Static Discharge ESD Radiated Emissions EMI All Peripheral interfaces intended for connection to external equipment are ESD EMI protected EN 61000 4 2 2000 ESD Immunity EN55022 1998 class B Generic Emission Standard Safety IEC 60950 1 2005 2 Edition UL 60950 1 CSA C22 2 No 60950 1 Product Category Information Technology Equipment In
82. d configure the memory controller for optimal performance If non SPD memory is used the BIOS will attempt to configure the memory settings but performance and reliability may be impacted Memory Operating Frequencies Regardless of the SODIMM type used the memory frequency will either be equal to or less than the processor system bus frequency For example if DDR3 1600 memory is used with a 1333 MHz system bus frequency processor the memory clock will operate at 666 MHz The table below lists the resulting operating memory frequencies based on the combination of SODIMMs and processors Processor A Memory Data system bus Resulting memory DIMM Type Module name transfers frequency clock frequency Mills MG Peak transfer rate DDR3 1333 PC3 10600 1333 1333 or more 666 DDR3 1600 PC3 12800 1600 1333 max 666 DDR3 1600 PC3 12800 1600 1600 800 Notes Kontron offers the following DDR3 204P SODIMM PN 1054 37801GB 1333MHZ PC3 10600 PN 1054 37761GB 1600MHZ PC3 12800 PN 1054 37812GB 1333MHZ PC3 10600 PN 1051 54032GB 1600MHZ PC3 12800 PN 1054 37824GB 1333MHZ PC3 10600 PN 1051 90574GB 1600MHZ PC3 12800 PN 1054 37838GB 1333MHZ PC3 10600 PN 1054 37758GB 1600MHZ PC3 12800 KTQM 77 KTHM 6 Users Guide KTD NO850 F System Specification 2 5 Graphics Subsystem The KTQM 77 equipped with Intel 3 Gen i3 i5 or i7 processor supports Intel HD Graphics 4000 equipped with Intel 2 Gen i3 i5 or i7
83. d during powerdown to allow 5V SB5V wakeup on USB device activity Protected by resettable 1A fuse covering both USB ports 6 6 4 USB Connector 12 13 USB12 13 J12 USB Ports 12 and 13 are supplied on the internal USB12 13 pinrow connector J12 Signal Description USB12 USB12 USB13 USB13 Differential pair works as Data Address Command Bus 5V supply for external devices SB5V is supplied during powerdown to allow 5V SB5V wakeup on USB device activity Protected by resettable 1A fuse covering both USB ports Note 1 In order to meet the requirements of USB standard the 5V input supply must be at least 5 00V Available cable kit e 0 0 GIZYO PN 821401 Bracket Dual USB Cable KTQM 77 KTHM76 Users Guide KTD NO850 F Page 45 Internal Connectors 6 7 Firewire IEEE1394 connectors J13 J14 The KTQM77 mITX only support two IEEE Std 1394a 2000 fully compliant ports at 100M bits s 200M bits s and 400M bits s 6 7 1 IEEE1394 connector IEEE1394 0 J14 Signal Type loh lol Pull Note 1 The 12V supply for the IEEE1394_0 devices is on board fused with a 1 25A reset able fuse Description TPA0 TPA0 Differential signal pair A TPBO TPBO Differential signal pair B 12V 12V supply 6 7 2 EEE1394 connector IEEE1394 1 J13 Pull U D PAO MA n GND PWR Por loh lol Type Sig
84. e KTD N0850 F Page 54 Internal Connectors 6 12 SPI Recover Jumper J4 The SPI Recover Jumper J4 is used to select BIOS Recovery Flash instead of BIOS Default Flash By default the J4 is not installed It is recommended that Jumper is plugged to J4 only in case the Default BIOS is corrupted so that board is malfunctioning and do not boot or the Recovery BIOS is requested to be upgraded in order to have sufficient or same support as the default BIOS In case Default BIOS seems corrupted then it is recommend to first trying to use the Load Default BIOS Settings Jumper see previous page When using customised BIOS it is recommended to upgrade both the Default BIOS and the Recovery BIOS with the Customised BIOS Recover corrupted Default BIOS procedure Turn off power Install SPI Recover Jumper J4 Reboot Remove SPI Recover Jumper Upgrade the BIOS fx execute Upd bat containing BF safewrite xxxxxx xxx When BIOS upgrade is completed then turn off power completely inclusive Standby 5V Wait minimum 10 seconds Turn on power System will automatically reboot 4 5 times within 1 minute ONOORWN Upgrade Recovery BIOS procedure Reboot Install SPI Recover Jumper J4 Upgrade the BIOS fx execute UpdRec bat containing BF safewrite xxxxxx xxx RECOVERY When BIOS upgrade is completed then turn off power completely inclusive Standby 5V Wait minimum 10 seconds Turn on
85. e P OK PWR OK signal are provided in the ATX12V Power SupplyDesign Guide It is strongly recommended to use an ATX or BTX supply in order to implement the supervision of the 5V and 3V3 supplies These supplies are not supervised on board Active low open drain signal from the board to the power supply to turn on the power supply outputs Signal must be pulled high by the power supply Warning Hot Plugging power supply is not supported Hot plugging might damage the board KTQM 77 KTHM76 Users Guide KTD NO850 F Page 38 Internal Connectors 6 2 Fan Connectors FAN CPU J28 and FAN SYS J29 The FAN CPU is used for the connection of the FAN for the CPU The FAN SYS can be used to power control and monitor a fan for chassis ventilation etc The 4pin header is recommended to be used for driving 4 wire type Fan in order to implement FAN speed control 3 wire Fan is also possible but no fan speed control is integrated 4 pin Mode CONTROL SENSE Description CONTROL PWM signal for FAN speed control Tacho signal from the fan for supervision The signals shall be generated by an open collector transistor or similar On board is a pull up resistor 4K7 to 12V The signal has to be pulsed typically twice per rotation 12V supply for fan A maximum of 2000mA can be supplied from this pin Power Supply GND signal 3 pin Mode m e O O 5 O TEE
86. e connector description KTQM 77 KTHM76 Users Guide KTD N0850 F Internal Connectors 6 9 3 Audio Header Connector AUDIO HEAD J31 Note Type Signal PIN Signal Type Note AAGND AAGND 1 FRONT OUT R 1 AAGND REAR OUT L AAGND 1 3 FRONT OUT L EE 7 9 REAR OUT R SIDE OUT L 11 SIDE OUT R AAGND MIC1 L 13 15 AAGND MIC1 R AAGND 17 AAGND LINE1 L NC 19 21 LINE1 R GND 23 SPDIF OUT 25 Note 1 Shared with Audio Stack connector Signal FRONT OUT L Description Front Speakers Speaker Out Left FRONT OUT R Front Speakers Speaker Out Right REAR OUT L Rear Speakers Surround Out Left REAR OUT R Rear Speakers Surround Out Right SIDE OUT L Side speakers Surround Out Left SIDE OUT R Side speakers Surround Out Right CEN OUT Center Speaker Center Out channel LFE OUT Subwoofer Speaker Low Freq Effect Out NC No connection MIC1 MIC Input 1 LINE1 Line 1 signals F SPDIF OUT S PDIF Output AAGND Audio Analogue ground Available cable kit PN 821043 Cable Audio Open End 300 mm KTQM 77 KTHM76 Users Guide KTD NO850 F Page 49 Internal Connectors 6 9 4 Front Panel Connector FRONTPNL J19 lol U D USB6 7 5V PWR USB7 USB7 GND GND NC LINE2 L 5V 5V SATA LED ME SUS LED GND 15 PWRBTN IN RSTIN 17 GND SB3
87. ective owners Disclaimer KONTRON Technology A S reserves the right to make changes without notice to any product including circuits and or software described or contained in this manual in order to improve design and or performance Specifications listed in this manual are subject to change without notice KONTRON Technology assumes no responsibility or liability for the use of the described product s conveys no license or title under any patent copyright or mask work rights to these products and makes no representations or warranties that these products are free from patent copyright or mask work right infringement unless otherwise specified Applications that are described in this manual are for illustration purposes only KONTRON Technology A S makes no representation or warranty that such application will be suitable for the specified use without further testing or modification Life Support Policy KONTRON Technology s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT EXPRESS WRITTEN APPROVAL OF THE GENERAL MANAGER OF KONTRON Technology A S As used herein Life support devices or systems are devices or systems which a are intended for surgical implant into body or b support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labelling can be reasonably expected to result in significant injury to the user A c
88. ector o DVI A Analogue Display CRT o 300 MHz Integrated 24 bit RAMDAC o Up to QXGA 2048x1536 pixels 75 Hz refresh o DVI D Digital Display up to WUXGA 1920x1200 pixels 260 Hz 2 5 4 Graphics Adapters Use of DP Adapter Converters can implement HDMI support or second VGA or DVI panel support The HDMI interface supports the HDMI 1 4a specification including audio codec However limitations to the resolution apply 2048x1536 VGA 1920x1200 HDMI and DVI ge 1051 7619 Cable DP Extender cable 200mm DP to VGA DP to HDMI DP to DVI D when using two DP converters PN 1045 5779 PN 1045 5781 PN 1045 5780 Notice that only the DP to VGA adapter is an active converter the HDMI and DVI converters are passive and cannot be used in a triple panel configuration KTQM 77 KTHM76 Users Guide KTD NO850 F System Specification 2 6 Power Consumption In order to ensure safe operation of the board the ATX12V power supply must monitor the supply voltage and shut down if the supplies are out of range refer to the hardware manual for the actual power supply specification Please note In order to keep the power consumption to a minimal level boards do not implement a guaranteed minimum load In some cases this can lead to compatibility problems with ATX power supplies which require a minimum load to stay in regulation The KTQMT7T7 mITX board is powered through the ATX 12V 4 pole connector and optionally also ATX BTX 24 p
89. efore IPv6 PXE Boot IPv6 Delay Time Note x T y Note1 Only if Network stack Enabled Note2 To enter number use digit keys and or keys KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Advanced 10 2 16 Advanced Delay Startup Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced Delay startup lt Select Screen Tl Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright O 2012 American Megatrends Inc Function Selection Description Delay Startup Note1 Delay startup value is in ms Note1 To enter number use digit keys and or keys The delay initiates if the value is different from 0 starts at the earliest possible point of the BIOS boot For some add on devices the BIOS boot is too fast for proper detection In other words the setting is meant as a possible fix to Add on device detection problems KTQM 77 KTHM76 Users Guide KTD N0850 F Page 100 BIOS Advanced 10 2 17 Advanced Serial Port Console Redirection Aptio Setup Utility Copyright O 2012 American Megatrends Inc Advanced COMO Console Redirection Enable or Disable Console Redirection Settings COMI Console Redirection Disabled Console Redirection Settings COM2 Console Redirection Disabled Console Redirection Settings COM3
90. emo E itkas GULF ODER pU 8 1 1 Installing the board uttter ten eni ree ee Peer por Eee ge e deter eeu ee trt 8 1 2 Requirement according to IEC60950 sse nn nennen nennen nnns nennen 9 MEE cuo ine po m 10 2 1 Component main data dc cid Pe E ue Tu deg kd ao S kad dan pik Tuta vi pie pk ei teeny san pi 10 22 MEENUNG Ee a ene EES EES EE pk pen pk oi ap aes 14 2 3 Processor Support Table at ccs erede bk aka a ea ok a pi ak deny eki dap oak bo ae pu pi gn 16 2 4 System Memory Supports acres ewa d ed o eH bete d age HERR kw n RR e w aah ak dot poke e 18 Sch Graphics SUbSYSTOM order an ak Eed aa 19 2 5 1 Intel HD Graphics 4000 ssssssssssseseseeeenen nennen ene nenrnnen nennen nennen nennen nennen eer nnne 19 2 5 2 Intel HB Graphics 3000 tao ie b fass pwal ote Lo EE E ah ELDER Eo aA dE du ep bidon dd ak d o aida 19 25 3 LVDS aid DVI RE 20 2 54 Graphics Adapters os ski ka ank p ae vei gedd EE Ey ER pp pa n ENEE Ed 20 2 6 Power Consumption 0 00 ee eeeeeeeeeeeeeeeeeeeeeeee cence ee eeaeeeeeceaeeeeeseaeeeeeceeeeeeseeeeeeeseeeaeeeceeeeeeeseeaeeeseeaeeeseenaees 21 3 Connector LOL ANONS e 27 CG HE E E 27 3 2 JO Bracket area aet e ee al ee ee dead kaa kad 28 KSC 28 4 Connector Def MUONS ek kiv t ik ko ki ian kk kk n ek ik k a ki n aa ki a a e k 29 5 gd ie pisan kk on ee ee eee 30 SL Display confiectors TOATA cuire euer ERE ke pa en kd pe ana kok aca pe a
91. en Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Selection Description Auto Launch CSM Always This option controls if CSM will be launched Never UEFI and Legacy i RS This option controls what devices system can Boot option filter Legacy only boot to UEFI only Do not launch Launch PXE OpROM Controls the execution of UEFI and Legacy PXE UEFI only policy OpROM Legacy only Do not launch Launch Storage OpROM UEFI oni Controls the execution of UEFI and Legacy policy y Storage OpROM Legacy only Launch Video OpROM Do not launch Controls the execution of UEFI and Legacy policy JER oniy Video OpROM Legacy only A For PCI devices other than Network Mass SEN PONCE Rou EE storage or Video defines which OpROM to priority Legacy OpROM EEN KTQM 77 KTHM76 Users Guide KTD NO850 F BIOS Security 10 5 Security Aptio Setup Utility Copyright 2012 American Megatrends Inc MERIT agasecurity EEGEN Password Description Set Administrator Password If ONLY the Administrator s password is set then this only limits access to Setup and is only asked for when entering Setup If ONLY the User s password is set then this is a power on password and must be entered to boot or enter Setup In Setup the User will have Administrator rights The password l
92. ength must be in the following range Minimum length Maximum length lt Select Screen User Password 11 Select Item Password on popup menu Enabled Enter Select Change Opt System Mode state Setup F1 General Help Secure Boot state Disabled F2 Previous Values F3 Optimized Defaults Secure Boot Enabled F4 Save amp Exit Secure Boot Mode Custom ESC Exit Image Execution Policy E Key Management HDD Security Configuration P1 ST3120827AS Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description See Password n Set Administrator Password description above Administrator Password See Password description above Disabled Enabled User Password Set User Password Password on popup menu Password on F7 popup boot menu A Secure Boot flow control Disabled Ni i Secure Boot Secure Boot is possible only if System runs in Enabled User Mode Secure Boot mode selector Standard Standard fixed Secure boot policy Custom Custom changeable Image Execution policy and Secure Boot Key databases Secure Boot Mode KTQM 77 KTHM76 Users Guide KTD NO850 F BIOS Security 10 5 1 Image Execution Policy Only visible if Secure Boot Mode Custom Aptio Setup Utility Copyright 2012 American Megatrends Inc Image Execution Policy on Option ROM Deny Execute Security Violation Image load Removable Media Deny Execute device
93. er Version V 2 05 02 Enables or Disables 64bit capable Devices to be Decoded PCI 64bit Resources Handling in Above 4G Address Space Only if System Supports 64 bit PCI Decoding gt PCI Express Settings gt PCI Express GEN 2 Settings lt Select Screen Tl Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright O 2012 American Megatrends Inc Function Selection Description Disabled Enables or Disables 64bit capable Devices to be Decoded in Above 4G Address Space Only Above 4G Decoding Enabled if System Supports 64 bit PCI Decoding Note The selection in bold is the default selection KTQM 77 KTHM 6 Users Guide KTD N0850 F BIOS Advanced 10 2 1 1 PCI Express Settings Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced PCI Express Link Register Settings Set the ASPM Level Force LOs Force all links to LOs State Auto BIOS auto configure WARNING Enabling ASPM may cause Disable Disabled ASPM Some PCI E devices to fail lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description Set the ASPM Level Force LOs Force all links to LOs Sta
94. ernally pull down 100Kohm Return Same as GND 3 3V Fused by 1 5A resetable PTC fuse common for DPO and DP1 KTQM 77 KTHM76 Users Guide KTD N0850 F IO Area Connectors 5 2 Ethernet Connectors The KTQM77 mITX supports three channels of 10 100 1000Mb Ethernet one ETH1 is based on Intel Lewisville 82579LM Gigabit PHY with AMT 8 0 support and the two other controllers ETHER2 amp ETHER3 are based on Intel Hartwell 82574L PCI Express controller The KTHM76 mITX support one channels of 10 100 1000Mb Ethernet ETH1 based on Intel Lewisville 82579LM Gigabit PHY AMT not supported In order to achieve the specified performance of the Ethernet port Category 5 twisted pair cables must be used with 10 100MB and Category 5E 6 or 6E with 1Gb LAN networks The signals for the Ethernet ports are as follows Description MDI 0 MDI O In MDI mode this is the first pair in 1000Base T i e the BI DA pair and is the transmit pair in 10Base T and 100Base TX In MDI crossover mode this pair acts as the BI DB pair and is the receive pair in 10Base T and 100Base TX MDI 1 MDI 1 In MDI mode this is the second pair in 1000Base T i e the BI DB pair and is the receive pair in 10Base T and 100Base TX In MDI crossover mode this pair acts as the BI_DA pair and is the transmit pair in 10Base T and 100Base TX MDI 2 MDI 2 In MDI mode this is the third pair in 1000Base T
95. et Reset the system after saving the changes Discard Changes and Reset Reset the system without saving any changes Save Changes Save Changes done so far to any of the setup options Discard Changes Discard Changes done so far to any of the setup options Restore Defaults Restore Load Default values for all the setup options Save as User Defaults Save the Changes done so far as User Defaults Restore User Defaults Restore the User Defaults to all the setup options Selection table of bootable devices When selected system will boot EE on selected device See note below Launch EFI Shell From Attempts to Launch EFI Shell application Shellx64 efi from one of the filesystem device available filesystem devices Note When pressing F7 while booting it is possible manually to select boot device KTQM 77 KTHM 6 Users Guide KTD NO850 F Page 139 BIOS Beep POST 11AMI BIOS Beep Codes Boot Block Beep Codes Number of ES Beeps Description Insert diskette in floppy drive A AMIBOOT ROM file not found in root directory of diskette in A Base Memory error Flash Programming successful Floppy read error Keyboard controller BAT command failed No Flash EPROM detected Floppy controller failure Boot Block BIOS checksum error Flash Erase error Flash Program error AMIBOOT ROM file size error BIOS ROM image mismatch file layout does not match image present in flash device
96. ge 50 Internal Connectors 6 10 Feature Connector FEATURE J30 loh lol CASE OPENZ 25I25mA O S5 25I25mA O PWR_OK O FAN3OUT PWR SB3V3 IOT GPIOO 1 IOT GPIO2 IOT GPIO4 GPIO5 IOT IOT GPIOG6 IAr GpPio7 IOT PWR GND EOR CND PWR 1 GPIO8 GPIO10 GPIO9 GPIO11 1 2 GPIO12 KR GPIO13 IOT IOT GPIO14 GPIO15 IOT 3 2 7 IOT GPIO16 29 30 GPIO17 IOT PWR GND 31 32 GND PWR 7 8 8mA O EGCLK ESER EGCS O 8 8mA 8 8mA EGAD TMAO O 12 6 2 8 8 PWR 12V 3 GND PWR FAN4OUT 39 40 FANAIN GND 41 42 GND 43 44 S3 25 25mA Notes 1 Pull up to 3V3Dual 3V3 or SB3V3 2 Pull up to on board Battery 3 Pull up to 3V3 Available cable kit PN 1052 5885 Cable Feature 44pol 1 to1 300mm KTQM 77 KTHM76 Users Guide KTD N0850 F Internal Connectors Signal Description CASE OPEN CASE OPEN used to detect if the system case has been opened This signal s status is readable so it may be used like a GPI when the Intruder switch is not required SMBC SMBus Clock signal SMBD SMBus Data signal S3 S3 sleep mode active low output optionally used to deactivate external system S5 S5 sleep mode active low output optionally
97. gs Note1 Device Mode Note1 Change the Printer Port mode Note1 only if Parallel Port Enabled KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Advanced 10 2 12 Advanced Voltage Monitor Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced Voltage Monitor VCore 1 05 lt Select Screen Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Advanced 10 2 13 Advanced Hardware Health Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced Hardware Health Configuration Disabled Full speed System Temperature 30 C 86 F Thermal does regulate fan System Temperature Ext 24 C 75 F speed according to specified CPU Temperature 49 10 C 120 F temperature System Fan Speed 1543 RPM Speed does regulate according to specified RPM Fan Cruise Control Thermal Fan Settings 35 Fan Min limit 0 Fan Max limit 100 CPU Fan Speed 1374 RPM lt Select Screen Fan Cruise Control Thermal T Select Item Fan Settings 50 Enter Select Fan Min limit 0 Change Opt Fan Max limit 100 F1 General Help F2 Previous Values Watchdog Function 0 F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2
98. ight 2012 American Megatrends Inc Graphics Configuration Graphics turbo IMON current IGFX VBIOS Version 2124 values supported 14 31 IGFX Frequency 350 MHz Primary Display Auto Internal Graphics Auto GTT Size 2MB Aperture Size 256MB DVMT Pre Allocated 64M DVMT Total Gfx Mem 256M Gfx Low Power Mode Enabled Graphics Performance Analyzers Disabled gt LCD Control lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc KTQM 77 KTHM76 Users Guide KTD N0850 F Function Graphics Turbo IMON Current Selection BIOS Chipset Description Graphics turbo IMON current values supported 14 31 Primary Display Internal Graphics GTT Size Aperture Size Auto Disabled Enabled 128MB 256MB 512MB Select which of IGFX PEG PCI Graphics device should be Primary Display Or select SG for Switchable Gfx Keep IGD enabled based on the setup options Select the GTT Size Select the Aperture Size DVMT Pre Allocated 32M 64M 96M 128M 160M 192M 224M 256M 288M 320M 352M 384M 416M 448M 480M 512M 1024M Select DVMT 5 0 Pre Allocated Fixed Graphics Memory size used by the Internal Graphics Device DVMT Total Gfx Mem 128M 256M MAX Select DVMT 5 0 Total Graphics Memory
99. iguration on the following pages Function Selection Description Power Off Restore AC Power Loss Power On Last State Select AC Power state when power is re applied after a power failure KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Chipset 10 3 1 1 PCI Express Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc PCI Express Configuration Enable or disable PCI Express Subtractive Decode Subtractive Decode Port PCI Express Root Port 1 PCI Express Root Port 2 PCI Express Root Port 3 PCI Express Root Port 4 PCI Express Root Port 6 PCI Express Root Port 7 PCI Express Root Port 8 lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description Disabled Enable or disable PCI Express Subtractive Enabled Decode Subtractive Decode Port 0 Select PCI Express Subtractive Decode Root Note1 Port User to ensure port availability Subtractive Decode Note1 Only visible if Subtractive Decode is Enabled Note2 To enter number use digit keys and or keys KTQM 77 KTHM76 Users Guide KTD NO850 F Page 109 BIOS Chipset 10 3 1 1 1PCI Express Root Port 1 4 6 8 Aptio Setup Utility Copyright 2012 American Megatrends Inc
100. imum worst case ambient operating temperature and the actual load of processor The Kontron PN 1044 9447 is Active Cooler for KTQM67 KTQM77 capable of being used for processors fully loaded having Thermal Guideline up to 45W 60 C ambient temperature MTBF is 70 000 hours 40 C The Kontron PN 1052 6345 Cooler Active KTQM67 35W 33mm longlife is capable of being used for processors fully loaded having Thermal Guideline up to 35W 60 C ambient temperature It support 1U and has long life MTBF is 200 000 hours 60 C All the processors in the list above inclusive the Celeron processor are supporting the Enhanced Intel SpeedStep which is improved SpeedStep technology for faster transition between voltage power saving states and frequency states with the result of improved power performance balance Intel Turbo Boost Technology 2 0 is supported by i5 and i7 as indicated in above list of processors and is enabling overclocking of all cores when operated within the limits of thermal design power temperature and current Intel vPro Technology is supported by some of the i5 and i7 not by Core i3 KTQM77 mITX only Intel AMT Active Management Technology supported by KTQM77 mITX only is a part of VPRO and is hardware and firmware technology that builds certain functionality into business PCs in order to remotely monitor maintain update upgrade and repair PCs Intel AMT relies on a hardware based
101. ing to Intel but also other CPU s if successfully tested Embedded CPU s are indicated by green text successfully tested CPU s are indicated by highlighted text successfully tested embedded CPU s are indicated by green and highlighted text and failed CPU s are indicated by red text Some processors in the list are distributed from Kontron those CPU s are marked by an asterisk However please notice that this marking is only guide line and maybe not fully updated 2 ET Processor Ka 5 sae Brand 818 5 gr c 8 MH 5 z a C W Core i7 2 4 1333 1600 4 3540M SROX6 L1 105 35 3 gen 2 4 1333 1600 4 3520M SROMU L1 105 35 4 8 1333 1600 8 3840QM SROUT E1 105 45 418 1333 1600 8 3820QM SROMK E1 105 45 418 1333 1600 6 3740QM SROUV E1 105 45 418 1333 1600 6 3720QM SROML E1 105 45 416 1333 1600 6 3630QM SROUX E1 105 45 418 1333 1600 6 3610QM SROMN E1 105 45 48 1333 1600 6 3610QE SRONP E1 105 45 418 1333 1600 6 3632QM SROVO E1 105 35 418 1333 1600 6 3612QM SROMQ E1 105 35 Core i7 2 4 1066 1333 4 2640M SRO3R J1 100 35 2 gen 214 1066 1333 4 2620M SRO3F J1 100 35 4 8 1066 1333 1600 8 2860QM SRO2X D2 100 45 4 8 1066 1333 1600 8 2920XM SRO2bE D2 100 55 4 8 1066 1333 1600 6 2760QM SRO2W D2 100 45 4 8 1066 1333 1600 8
102. ious Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc SMX Intel Secure Mode Extension instructions are enabled if supported by the CPU so no BIOS settings are present VT Intel Virtualization Technology is enabled disabled in the menu Advanced gt CPU Configuration VT d can be enabled disabled in the menu Chipset gt System Agent SA Configuration Function Selection Description Disabled Intel TXT support Enabled Enables or Disables Intel TXT LT support KTQM 77 KTHM 6 Users Guide KTD N0850 F BIOS Advanced 10 2 7 Advanced AMT Configuration AMT Configuration is only present when using KTQM77 mITX Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced Enable Disable Intel Active BIOS Hotkey Pressed Disabled Management Technology BIOS MEBx Selection Screen Disabled Extension Hide Un Configure ME Confirmation Disabled Note iAMT H W is always MEBx Debug Message Output Disabled enabled Un Configure ME Disabled This option just controls the AMT Wait Timer 0 BIOS Extension execution Disable ME Disabled If enabled this requires ASF Enabled additional firmware in the SPI Active Remote Assistance Process Disabled device USB Configure Enabled PET Progress Enabled AMT CIRA Timeout 0 Disabled lt Select Screen 1 Select Item Enter Select Cha
103. le PEG Auto Detect Non Compliance Device Disabled De emphasis Control 3 5 dB PEG Sampler Calibrate Swing Control Gen3 Equalization Gen3 Eq Phase 2 PEG Gen3 Root Port Preset Value for each Lane PEG Gen3 Endpoint Preset Value each Lane AE PEG Gen3 Endpoint Hint Value each Lane ez ki a e Gen Eq Preset Search Disabled PEG Link Disabled Disabled Change Opt Fast PEG Init Enabled F1 General Help RxCEM Loop back Disabled F2 Previous Values PCIe Gen3 RxCTLEp Setting 12 F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Note PCle PEG Bifurcation is only supported on KTQM77 mITX having PCB ID 01 or above KTQM 77 KTHM 6 Users Guide KTD N0850 F Function PEGO Gen X PEGO ASPM Selection Disabled Auto ASPM LOs ASPM L1 ASPM LOsL1 BIOS Chipset Description Configure PEGO B0 D1 FO Gen1 Gen3 Control ASPM support for the PEG Device 1 Function 0 This has no effect if PEG is not the currently active device PCle PEG Bifurcation 1x16 2x8 1 x8 2 x4 2 x8 and 1 x8 2 x4 need Riser Card with bifurcation functionality to work Only supported on KTQM77 mITX having PCB ID 01 or above Enable PEG Disabled Enabled Auto To enable or disable the PEG Detect Non Compliance Device Disabled Enabled Detect Non Compliance PCI Express Device in PEG De emphasis Control 6 dB 3 5
104. le continued BIOS Chipset Function Selection Description Dynamic 1 GB 1 25 GB 1 5 GB A 1 75 GB Maximum Value of TOLUD Dynamic assignment would adjust TOLUD Max TOLER a x GB automatically based on largest MMIO length of installed graphic controller 2 5 GB 2 75 GB 3 GB 3 25 GB Auto NMode Support 1N Mode Nmode Support Option 2N Mode Memory Scrambler pnan Enable or disable memory scrambler Disabled MRC Fast Boot End Enable or disable MRC Fast Boot Disabled Force cold reset or choose MRC cold reset EE Enabled mode when cold boot is required during MRC SO ees Disabled execution Note If ME 5 0MB is present Force cold reset is required Auto DIMM Exit Mode Slow Exit DIMM Exit Mode control Fast Exit No Power Down APD Power Down Mode PPD Power Down Mode control APD PPD S PETENS GES Control Memory Scrambler Seed Generation kile i Enable do not generate scrambler seed Generation Off Disabled Disable Generate scrambler seed always Enabled Memory Remap Disabled Enable or disable Memory Remap above 4G 1 Enabled Memory Alias Check Disabled Enable or disable Memory Alias Check Enable Both DIMMS Disable DIMMO Channel A DIMM Control Disable DIMM1 Enable or disable dims on channel A Channel B DIMM Control Disable Both DIMMS Enable Both DIMMS Disable DIMMO Disable DIMM1 Disable Both DIMMS Enable or disable dims on channel B KTQM 77 KTHM76 Users Guide
105. lity Copyright 2012 American Megatrends Inc Advanced Super IO Configuration Set Parameters of Serial Port 1 COMA Super IO Chip IT8516F gt Serial Port 2 Configuration Super IO Chip W83627H gt Serial Port 3 Configuration gt Serial Port 4 Configuration gt Parallel Port Configuration lt Select Screen Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Note Parallel Port is not available connector not mounted The 5 submenus are shown and described on the following pages KTQM 77 KTHM76 Users Guide KTD NO850 F Page 88 BIOS Advanced 10 2 11 1 Serial Port 1 Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced Serial Port 1 Configuration Enable or Disable Serial Port COM Device Settings IO 3F8h IRQ 4 Change Settings Auto lt Select Screen Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description Serial Port Disabled Enable or Disable Serial Port Enabled COM Auto IO 3F8h IRQ 4 Change Settings Note1 O 3F8h IRQ 3 4 5 6 7 10 11 12 Select an optimal setting for Super IO 2F8h IRQ 3 4 5 6 7 10 11 12 IO device IO 3E8h IRQ 3 4
106. mouse KDBCLK Bi directional clock signal used to strobe data commands from to the PC AT keyboard Bi directional serial data line used to transfer data from or commands to the PC AT keyboard KBDDAT Available cable kit PN 1053 2384 Bracket Cable 6 Pin to PS2 Kbd Mse KTQM 77 KTHM76 Users Guide KTD N0850 F Internal Connectors 6 4 Display connectors Internal The KTQM 7 provides internal display connectors one on board LVDS panel interface and one on board eDP Embedded DisplayPort KTQM77 mITX only LVDS and eDP and cannot be used at the same time For IO Area Display Connectors DVI I and two DP s see earlier section 6 4 1 eDP connector EDP J38 The eDP connector KTQM77 mITX only is based on single in line 40 pole connector type TYCO 5 20697 16 3 Pin Signal Description Type Note Fused by 1 5A resetable PTC fuse Backlight Voltage 12V in SO mode Back Light PWM Pulse Width Modulated To adjust Back Light intensity Back Light Enable To enable the Back Light Backlight GND HPD Hot Plug Detection LCD GND LCD GND LCD GND LCD GND NC LCD VCC LCD VCC LCD VCC LCD VCC GND Aux n Aux p GND Lane 0 p Lane 0 n GND Lane 1 p Lane 1 n GND Lane 2 p Lane 2 n GND Lane 3 p Lane 3 n GND NC Display panel GND Shared with LVDS connector Display panel voltage 3 3V or 5V selected in BIOS Fused by
107. nal PIN signal ILI 2 4 6 8 1 Note 1 The 12V supply for the IEEE1394_1 devices is on board fused with a 1 25A reset able fuse Description TPA1 TPA1 Differential signal pair A TPB1 TPB1 Differential signal pair B 12V 12V supply KTQM 77 KTHM76 Users Guide KTD N0850 F Page 46 Internal Connectors 6 8 Serial COM1 COMA Ports J15 J16 J17 J18 Four RS232 serial ports are available on the KTQMT77 The typical definition of the signals in the COM ports is as follows Description Transmitted Data sends data to the communications link The signal is set to the marking state 12V on hardware reset when the transmitter is empty or when loop mode operation is initiated Received Data receives data from the communications link Data Terminal Ready indicates to the modem etc that the on board UART is ready to establish a communication link Data Set Ready indicates that the modem etc is ready to establish a communications link Request To Send indicates to the modem etc that the on board UART is ready to exchange data Clear To Send indicates that the modem or data set is ready to exchange data Data Carrier Detect indicates that the modem or data set has detected the data carrier Ring Indicator indicates that the modem has received a ringing signal from the telephone line The pinout of Serial ports COM1 J15 COM2 J16 COM3 J17 and COM
108. nal load Supply Current draw Power consumption A eee A IW E PATE 0 099 Total S5 Mode Mean No external load Current draw Power consumption Supply W 12V P4 Total KTQM 77 KTHM76 Users Guide KTD NO850 F System Specification c High Power Setup KTQM77 mITX ATX 12V PSU TBD DOS Idle Mean No external load CSN A W 11 184 12V P4 13 224 5V 3V3 12V 5VSB Total Windows 7 mean 3DMARK2005 first scene amp BiT 6 A W 16 260 S0 Mode Mean No external load A W 6 828 5 820 2 100 3 812 0 588 0 035 18 6 Power consumption W S5 Mode Mean No external load Current draw Power consumption A W 0 219 KTQM 77 KTHM76 Users Guide KTD NO850 F System Specification d High Power Setup KTQM77 mITX 12V only PSU TBD DOS Idle Mean No external load Current draw Power consumption Supply A w 12V P4 2 499 Total Windows 7 mean 3DMARK2005 first scene amp BiT 6 Current draw Power consumption Suppl asa A W 12V P4 6 712 Total S0 Mode Mean No external load Current draw Power consumption SHBPly A w 12V P4 1 615 Total S3 Mode Mean No external load Supply Current draw Power consumption A M 12V P4 0 104 Total S5 Mode Mean No external load Current draw Power consumption Supply EET W 12V P4 1 212 t
109. nge Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Watchdog OS Timer 0 BIOS Timer 0 Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description Enable Disable Intel Active Management Technology BIOS Extension Note iAMT H W is always enabled Disabled ANT Intel AMT This option just controls the BIOS Extension Enabled execution If enabled this requires additional firmware in the SPI device BIOS Hotkey Pressed Disabled OEMFlag Bit 1 Note1 Enabled Enable Disabled BIOS hotkey press MEBx Selection Screen Disabled OEMFlag Bit 2 Note1 Enabled Enable Disabled BIOS MEBx Selection Screen EMFlag Bit 6 Hide Un Configure ME Disabled Se e e ME without T Contimer Note1 Enabled ide Un Configure without passwor Confirmation Prompt MEBx Debug Message Disabled OEMFlag Bit 14 Output Note1 Enabled Enable MEBx Debug Message Output Un Configure ME Note1 Disabled OEMFlag Bit 15 Enabled Un Configure ME without password KTQM 77 KTHM76 Users Guide KTD N0850 F Function AMT Wait Timer Note1 Selection 0 65535 Note4 BIOS Advanced Description Set timer to wait before sending ASF_GET_BOOT_OPTIONS Disable ME Note1 Disabled Enabled Set ME to Soft Temporary Disabled ASF Note1 Disabled Enabled Enable Disabled Alert Specification Format Active Remote
110. nly supported when using 3rd generation Intel Core processor Ivy Bridge The two miniPCle PCle 2 0 is located on the backside of the board The 1 lane x1 PCI Express PCle 2 0 can be used for any PClex1 cards inclusive Riser PClex1 to PCI Dual flexible card 7 1 1 PCI Express x16 Connector PCle x16 Note Type Signal 12V 12V 12V GND SMB_CLK SMB_DATA B9 A9 B10 A10 B11 A11 NC B12 A12 GND GND B13 A13 PCIE x16 CLK PEG TXP 0 B14 A14 PCIE x16 CLK PEG TXN 0 B15 A15 GND GND B16 A16 PEG RXP 0 CLKREQ B17 A17 PEG_RXN 0 GND B18 Aug GND PEG_TXP 1 B19 A19 NC PEG TXN 1 B20 A20 GND GND B21 A21 PEG RXPI1 GND B22 A22 PEG RXN 1 PEG TXP 2 B23 A23 GND PEG TXN 2 B24 A24 GND GND B25 A25 PEG RXPI2 GND B26 A26 PEG RXN 2 PEG TXP 3 B27 A27 GND PEG TXN 3 B28 A28 GND GND B29 A29 PEG RXP 3 NC B30 A30 PEG RXN 3 CLKREQ B31 A31 GND GND B32 A32 NC PEG TXP 4 B33 A33 NC PEG TXNI4 B34 A34 GND GND B35 A35 PEG BNP KTQM 77 KTHM76 Users Guide KTD N0850 F Slot Connectors GND PEG_TXP 5 PEG_TXN 5 GND GND PEG TXP 6 PEG TXN 6 GND GND PEG TXPI7 PEG TXN 7 GND CLKREQ GND PEG TXP 8 PEG TXN 8 GND GND PEG TXP
111. nse Technology OROM UI Delay Enabled Enabled Enabled 2 Seconds Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc KTQM 77 KTHM76 Users Guide KTD NO850 F Page 78 BIOS Advanced Submenu Software Feature Mask Configuration description Function Selection Description RAIDO Bes Enable or disable RAIDO feature Enabled RAID1 ee Enable or disable RAID1 feature Enabled RAID10 peewee Enable or disable RAID 10 feature Enabled RAID5 ege Enable or disable RAIDS feature Enabled Intel Rapid Recovery Disabled Enable or disable Intel Rapid Recovery Technology Enabled Technology If enabled then the OROM UI is shown Disabled Otherwise no OROM banner or information will El ee be displayed if all disks and RAID volumes are Normal Disabled If enabled indicates that the HDD password HIDD Unoa Enabled unlock in the OS is enabled Disabled If enabled indicates that the LED SGPIO LED Locate Enabled hardware is attached and ping to locate feature ase is enabled on the OS If enabled then only IRRT volumes can span Disabled internal and eSATA drives If disabled then any JSESU CE GN eoo Enabled RAID volume can span internal and eSATA drives EE Dod Enable or disable Smart Response
112. o adapter is an integrated part of the system board the board may be faulty Troubleshooting Action Note If Motherboard beeps fast for approximately two seconds 20 beeps and then turns off then Jumper J37 is missing meaning that Load Default BIOS Settings function is enabled until J37 is back in place KTQM 77 KTHM76 Users Guide KTD N0850 F OS Setup 120S Setup Use the Setup exe files for all relevant drivers The drivers can be found on KTQM 7 Driver CD or they can be downloaded from the homepage http www kontron com For some OS like Win7 when installing OS via USB DVD USB Keyboard Mouse please connect the USB DVD USB Keyboard Mouse to USB2 0 ports only or disable USB3 0 in BIOS KTQM 77 KTHM76 Users Guide
113. ole connector Single 12V supply When powered by 12V only via ATX 12V connector then limitations apply to 5V where 14x USB LVDS panel or eDP panel COM ports LPT port and Frontpanel connector shares 9 5A 4 pole connector power limitation is 145W maximum but if required more 12V power can be added via 12V and GND terminals in the 24 pin power connector It is allowed to use the 12V and 5V from the 24 pole connector in order to drive external devices but please notice that it is not allowed to use the SB5V POK and PSON signals ATX12V supply When powered as standard ATX12V then both ATX 12V connector and ATX BTX connector must be used in according to the ATX12V PSU standard Warning Hot Plugging power supply is not supported Hot plugging might damage the board The requirements to the supply voltages are as follows Supply Should be 5 for compliance with the ATX specification Should be 5 for compliance with the ATX specification Should be 5 0 to meet the USB standard Should be 5 for compliance with the ATX specification Should be 10 for compliance with the ATX specification Not required for the KTQM77 boards Should be 5 for compliance with the ATX specification Total System power example TBD CPU GHz GB Ram 1x xxxgb HDD 1x DVD ROM PSU Power Supplied via Operation 12V Only Windows 7 32bit Idle 33W 36W Windows 7 32bit 3Dmark 2003 7OW 88W 72W 96W Windows 7 32bit Intel
114. omponent vendors KTQM 77 KTHM76 Users Guide KTD N0850 F 5 IO Area Connectors IO Area Connectors 5 1 Display connectors IO Area The KTQM77 provides one on board DVI I port both digital and analogue two on board DP s DisplayPort one on board eDP Embedded DisplayPort and one on board LVDS panel interface Two graphic pipes are supported meaning that up to two independent displays can be implemented using any two of the above mentioned graphic ports 5 1 1 DVI Connector DVI I J41 The DVI I connector support DVI Digital output and DVI Analogue output eelas eI fe 9 1o Jr rs e r6 7 ve fre o2 22 23 24 Female socket front view Signal Description DVI Connector Description Type Pull U D 1 TMDS Data 2 Digital Red Link 1 LVDS OUT 2 TMDS Data 2 Digital Red Link 1 LVDS OUT 3 TMDS Data 2 4 Shield PWR 4 NC NC 5 NC NC 6 DDC Clock DDC Clock IO 2K2 7 DDC Data DDC Data IO 2K2 8 NC NC 9 TMDS Data 1 Digital Green Link 1 LVDS OUT 10 TMDS Data 1 Digital Green Link 1 LVDS OUT 11 TMDS Data 1 3 Shield PWR 12 NC NC 13 NC NC 14 5V Power for monitor when in standby PWR 15 GND PWR 16 Hot Plug Detect Hot Plug Detect 17 TMDS Data 0 Digital Blue Link 1 Digital sync LVDS OUT 18 TMDS Data 0 Digital Blue Link 1 Digital sync LVDS OUT 19 TMDS Data
115. on 2 15 1226 Copyright O 2012 American Megatrends Inc KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Chipset 10 3 2 4 Memory Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc Memory Information A that should be used Memory RC Version 1 5 0 0 Memory Frequency 1333 Mhz Total Memory 4096 MB DDR3 DIMM 0 4096 MB DDR3 DIMM 2 Not Present CAS Latency tCL 9 Minimum delay time CAS to RAS tRCDmin 9 Row Precharge tRPmin 9 Active to Precharge tRASmin 24 XMP Profile 1 Not Supported XMP Profile 1 Not Supported lt Select Screen 1 Select Item Enter Select Memory Frequency Limiter Auto Change Opt ECC Support Enabled F1 General Help Max TOLUD Dynamic F2 Previous Values NMode Support Auto F3 Optimized Defaults Memory Scrambler Enabled F4 Save amp Exit MRC Fast Boot Enabled ESC Exit Force Cold Reset Enabled DIMM Exit Mode Fast Exit Power Down Mode PPD Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description Default DIMM profile Custom Profile XMP Profile 1 XMP Profile 2 Auto 1067 1333 1600 Maximum Memory Frequency Selections in 1867 Mhz 2133 2400 2667 Disabled Enabled DIMM profile Select DIMM timing profile that should be used Memory Frequency Limiter ECC Support Enable or disable DDR Ecc Support KTQM 77 KTHM76 Users Guide KTD N0850 F Tab
116. on Enables Legacy USB support AUTO option disables legacy USB Module Version support if no USB devices are connected DISABLE option USB Devices will keep USB devices available 2 Hubs only for EFI applications USB3 0 Support Disabled XHCI Hand off Enabled EHCI Hand off Disabled USB Mass Storage Driver Support Enabled USB hardware delays and time outs lt Select Screen USB transfer time out 20 sec Device reset time out 20 sec Device power up delay Auto Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc KTQM 77 KTHM76 Users Guide KTD N0850 F Function Selection BIOS Advanced Description Enables Legacy USB support Enabled AUTO option disables legacy support if no USB Legacy USB Support Disabled devices are connected DISABLE option will Auto keep USB devices available only for EFI applications Enabled Enable Disable USB3 0 XHCI Controller USB3 0 Support Disabled support This is a workaround for OSes without XHCI Enabled hand off support AHE Pandor Disabled The XHCI ownership change should be claimed by XHCI driver This is a workaround for OSes without EHCI Enabled hand off support EE Disabled The EHCI ownership change should be claimed by EHCI driver USB Mass Storage Driver Enabled Enable disable USB Mass Storage Driver Support Disabled Suppor
117. ooler KT PSU Corsair 430W c High Power Setup KTQM77 mITX ATX 12V PSU d High Power Setup KTQM77 mITX 12V only PSU Standard system configuration equipped with PClex1 PClex16 miniPCle WLAN 4x SATA disks Intel i7 CPU 2x SODIMM 1GB Modules Monitor Keyboard 8 Mouse 4x 1 4GB USB Sticks 12V active cooler KT PSU Corsair 430W KTQM 77 KTHM76 Users Guide KTD NO850 F System Specification a Low Power Setup KTQM77 mITX ATX 12V PSU TBD DOS Idle Mean No external load Supply Current draw Power consumption A W 12V 12V P4 5V Windows 7 mean 3DMARK2005 first scene amp BiT 6 BET A W 1 980 12V P4 39 000 S0 Mode Mean No external load Current draw A 12V 12V P4 S3 Mode Mean No external load Current draw A 0 218 S5 Mode Mean No external load Current draw Power consumption A W KTQM 77 KTHM76 Users Guide KTD NO850 F System Specification b Low Power Setup KTQM77 mITX 12V only PSU TBD DOS Idle Mean No external load Supply Current draw Power consumption A W 12V P4 1 721 Total Windows 7 mean 3DMARK2005 first scene amp BiT 6 Supply Current draw Power consumption A IW 12V P4 3 940 Total 47 3 S0 Mode Mean No external load Current draw Power consumption vais A IW 12V P4 0 992 11 904 Total us o S3 Mode Mean No exter
118. ot Connectors PCle miniPCIe BELL usu etegeresegeusgs egseeuesgeseb rkCeugee 58 MM uarie fem 58 7 1 1 iPOL Express x16 Connector P IE XTO aza sizan ci pon tec O ke desk pedan ape da ay 58 7 1 2 miniPCI Express mPCIeO 34 60 1 4 3 mimPCI Express mPCIe4 D EE 61 7 1 4 PCI Express x1 Connector PCIex4 J36 1 5 dec tiene e akle enhance de sak he nie d Ee Ene ide 62 8 On board 8 mating connector types eene 63 9 System EE 64 HL Memo Map EMI 64 EC RU i gi SET Le 65 94 IO U 1 cad tice be e EL UT bb tik td i on Ra rera dete adt ere Leah E ak ka a ER rara Med aad 66 10 Bee n 67 NY DEENEN LTE 67 10 2 WUEDCE 68 10 2 1 Advanced PCI Subsystem Settings ka aaat nennen nennen nennen nnn nennen nennen 69 10 2 2 Advanced APCISettings sssssssssesesseeeeeenenen aaa ae tuun SEEE nennen nennen nennen nennen nenne ener 72 10 2 3 Advanced Trusted Computing i acciaio tee i beke kaa pad day dd wan pti ed e Ed dau pti abated don koi 73 10 2 4 Advanced CPU CONAQUAATI N was yota cid tinent dete a ai dap eda E A pi kan vy won pa 74 10 2 5 Advanced SATA Configuration 2 c c 0ccceciceectanceccssticeestanactecssnadeest ni v ede sta dees ak aske sia d v kd ud t da 76 10 2 6 Advanced Intel TXT LT Configuration nennen nenne nennen nennen enn 80
119. ote 000 2 KTQM 77 KTHM76 Users Guide Sata1 Sata4 Sata2 Sata0 Sata5 Sata3 see note below USB9 FEATURE USB8 ATX BTXPWR n DDR3 Slot 1 ede deae e dede e Ded hel be re Ne 11759 DEER Xm Oe Geng EI FRONTPNL 1 D DDR3 Slot 0 T 5 TI TI Pi oi o w c i IL 11692530300 COMS3 A E E NI Q Q O O N gt IEEE1394 1 IEEE1394 0 ate vee KBDMSE Q o AUDIO HEAD USB5 ETH2 USB1 USB3 DV Load Default USB4 ETH3 USBO USB2 LVDS BIOS Settings DPO DP1 Notes Sata0 Sata1support up to 6GB s and Sata2 Sata3 Sata4 Sata5 support up to 3GB S SATA2 is shared with mPCle0 USBO USB3 supports USB3 0 USB2 0 Not available connectors on KTHM76 mITX IEEE 1394 0 IEEE 1394 1 ETH2 ETH3 and EDP ETH2 ETH3 KTQM 7 only XDP CPU XDP PCH below mPCle1 pU 8104104500 R11 S N 6606000600000606060020606606000000606000060 GO e 000606000006000 o The XDP and LPT connectors are not supported and not mounted in volume production Kontron sub supplier number Please use the SN label on the PCle x16 slot which is the board SN matching the SN in BIOS KTD N0850 F Connector Definitions 4 Connector Definitions The following sections provide pin definitions and detailed description of all on board connectors The connector definitions follow the following notation Column Description
120. path Fixed Media Deny Execute lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Selection Description Image Execution Policy on Security Violation Internal FV Always Execute Image load device path Always Execute Always Deny Allow Execute Image Execution Policy on Security Violation ER Defer Execute Image load device path Deny Execute Query User Always Execute Always Deny Allow Execute Image Execution Policy on Security Violation Defer Execute Image load device path Deny Execute Query User Removable Media Always Execute Always Deny Fixed Media Allow Execute Image Execution Policy on Security Violation Defer Execute Image load device path Deny Execute Query User KTQM 77 KTHM76 Users Guide KTD NO850 F BIOS Security 10 5 2 Key Management Only visible if Secure Boot Mode Custom Aptio Setup Utility Copyright 2012 American Megatrends Inc Force OEM default Secure Boot Keys if System is in Setup Manage All Factory Keys PK KEK DB DBX Mode Install default Secure Boot keys Platform Key PK NOT INSTALLED gt Set PK from File Get PK to File gt Delete the PK Key Exchange Key Database KEK NOT INSTALLED Set KEK from File Get KEK to File Delete
121. power System will automatically reboot 4 5 times within 1 minute If boot succeed then remove SPI Recover Jumper NOORWN Upgrade first Default BIOS and then Recovery BIOS with Customised BIOS procedure Reboot Upgrade the BIOS fx execute Upd bat When BIOS upgrade is completed then turn off power completely inclusive Standby 5V Wait minimum 10 seconds Turn on power System will automatically reboot 4 5 times within 1 minute Install SPI Recover Jumper J4 Upgrade the BIOS fx execute UpdRec bat When BIOS upgrade is completed then turn off power completely inclusive Standby 5V Wait minimum 10 seconds 10 Turn on power System will automatically reboot 4 5 times within 1 minute 11 Remove SPI Recover Jumper Note It is not recommended to upgrade both Default BIOS and Recovery BIOS without rebooting and verification in between unless you are sure that BIOS and tools works correctly Otherwise there is a risk that both BIOS will be corrupted at the same time with the result that board cannot be recovered KTQM 77 KTHM76 Users Guide KTD NO850 F Page 55 Internal Connectors 6 13 SPI Connector SPI J5 The SPI Connector is normally not used If however a SPI BIOS is connected via the SPI Connector then the board will try to boot on it Note Pull U D loh lol Type Signal PIN Signal loh lol Pull U D Note
122. rboard resources OxFED45000 OXFED8FFFF 4B000 Motherboard resources OxFED40000 OxFEDAAFFFE 5000 System board OxFED20000 OXFED3FFFF 20000 Motherboard resources OxXFED1COOO OxFEDIFFFFE Motherboard resources OxFED19000 OXFEDIOFFF Motherboard resources OxFED18000 OXFEDI8FFF Motherboard resources OxFED10000 OXFEDI7FFF 8000 Motherboard resources OxFED0OO000 OxFEDOO3FF 400 High Precision Event Timer OxF8000000 OXFBFFFFFF 4000000 Motherboard resources OxF7F3B000 OxF7F3BOOF Intel Management Engine Interface OxF7F39000 OxF7F39FFF Intel 82579LM Gigabit Network OxF7F38000 OxF7F383FF Intel Chipset USB EHCI 1E2D OxF7F37000 OxF7F373FF Intel amp Chipset USB EHCI 1E26 OxF7F36000 OxF7F367FF 800 Intel Chipset 6 port SATA ACHI 1E03 OxF7F35000 OxF7F350FF 100 Intel Chipset SMBus Controller 1E22 OxF7F30000 OxF7F33FFF 4000 High Definition Audio Controller OxF7F00000 OxF7FIFFFF 20000 Intel 82579LM Gigabit Network OxF7E00000 OxF7EFFFFF 100000 Intel Chipset PCIe Root port 3 1E14 OxF7D00000 OxF7DFFFFF 100000 Intel Chipset PCIe Root port 4 1E16 OxF7C00000 OxF7CFFFFF 100000 Intel Chipset PCIe Root port 6 IELA OxF7800000 OXF7BFFFFF 400000 Intel HD Graphics 4000 Family 0xE0000000 OxXEFFFFFFF 10000000 Intel HD Graphics 4000 Family OxDFA00000 Ox40000000 OxDFAOOFFF OxX401FFFFF 1000 200000 Motherboard resources BET bus System board
123. rican Megatrends Inc Function Selection Description Set the LVDS Display Panel voltage to either LCDVCC Voltage 5V 3 3V or 5V Select Disabled if BKLTEN signal available in the LVDS connector shall behave normally active low to enable backlight Select Enabled if BKLTEN signal shall behave inversed active high to enable backlight Disabled Backlight Signal Inversion Enabled KTQM 77 KTHM76 Users Guide KTD N0850 F Page 97 BIOS Advanced 10 2 15 Advanced LAN Configuration Aptio Setup Utility Copyright 2012 American Megatrends Inc EN coooo Wl LAN Configuration Control of Ethernet Devices and System UUID f4af2da3 b59d 58a9 466cb11a02b0486f PXE boot To disable ETH1 ME Subsystem must be as well Wake on LAN Enabled MAC Address amp Link status OOEOF4288EA3 ETH2 Configuration Upper Enabled MAC Address amp Link status OOEOF4288EA4 ETHS Configuration Lower Enabled MAC Address amp Link status OOEOF4288EA5 Network Stack lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults Version 2 15 1226 Copyright 2012 American Megatrends Inc Note ETH2 Configuration Upper and ETH3 Configuration Lower are only present if using KTQM 77 mITX Selection Description Disabled ETH1 Configuration Left Enabled With PXE boot Control of Ethernet Devices and PXE
124. ritical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness KTQM 77 KTHM76 Users Guide KTD NO850 F Page 3 Document details KONTRON Technology Technical Support and Services If you have questions about installing or using your KONTRON Technology Product check this User s Manual first you will find answers to most questions here To obtain support please contact your local Distributor or Field Application Engineer FAE Before Contacting Support Please be prepared to provide as much information as possible e CPU Board 1 Type 2 Part Number find PN on label 3 Serial Number if available find SN on label e Configuration 1 CPU Type Clock speed 2 DRAM Type and Size 3 BIOS Revision Find the Version Info in the BIOS Setup 4 BIOS Settings different than Default Settings Refer to the BIOS Setup Section e System 1 O S Make and Version 2 Driver Version numbers Graphics Network and Audio 3 Attached Hardware Harddisks CD rom LCD Panels etc Warranty KONTRON Technology warrants its products to be free from defects in material and workmanship during the warranty period If a product proves to be defective in material or workmanship during the warranty period KONTRON Technology will at its sole option repair or replace the produ
125. rows KTQM77 only Six USB 2 0 ports on internal pinrows KTHM76 only Two IEEE 1394a 2000 up to 400M bits s on internal pinrows KTQM77 only Four Serial ports RS232 on internal pinrows Two Serial ATA 600 IDE interfaces Four Serial ATA 300 IDE interfaces RAID 0 1 5 10 support KTQM77 only mSATA via mPCle 0 connector PS 2 keyboard and mouse ports via pinrow Expansion Capabilities 1x 10 100 1000Mbits s LAN ETHER1 using Intel Lewisville 82579LM Gigabit PHY connected to QM77 supporting AMT 8 0 AMT only on KTQM77 2x 10 100 1000Mbits s LAN ETHER2 ETHER3 using Intel Hartwell 82574L PCI Express controllers KTQM77 only PXE Netboot supported Wake On LAN WOL supported PCI Express slot s o 1 slot PCle x16 PCle 2 0 and up to PCle 3 0 when using Ivy Bridge CPU o 1slot PCle x1 PCle 2 0 o 1 slot miniPCI Express PCI Express or mSATA signals no USB signals o 1 slot miniPCI Express PCI Express signals no mSATA or USB signals SMBus compatible with ACCES BUS and I2C BUS via Feature connector SPI bus routed to SPI connector DDC Bus routed to DVI I connector 18 x GPIOs General Purpose l Os via Feature connector DAC ADC PWM and TIMER Multiplexed via Feature connector WAKE UP Interrupt Inputs Multiplexed via Feature connector 3 Wire Bus for GPIO Expansion up to 152 GPIOs via Feature connector 8 bit Timer output via Feature connector KTQM 77 KTHM76 Users Guide KTD NO850
126. ry dama palais 30 5 1 1 DVI Connector DVI I 41 EE 30 5 1 2 DPConnectors DPO DP1 140 139 2 eitis de onsi dwe rta nane bak dd gne aed ea ind aka koi con addu Rada 31 5 2 Ethernet Connectors kel ssi ne e e a deett edebat ee du ke Hd ebat aea A p eb da edel nde 32 5 3 USB Connectors IO Area cierto o e to a ipse tob pd ed ka ason ia 33 5 3 1 USB Connector 0 1 USBO 1 isssssssesseeeneennen nennen nne ne rennen ener enitn en nennen 34 5 3 2 USB Conriector 2 3 USB2 3 tint t t ete rt ad eed ada e t agus Eed EES 35 5 3 3 USB Connector 4 5 USB4 5 iye ee vini avwan e vev reete enter EELER eva ga ER ARD eee Ra 35 5 4 Audio Connector I0 Area eri etre e rre b Ende Ln api da pi di aba CO RE Lege aa rx Ida Ea 36 6 Internal Connectors E 37 6 1 Power Connector ATX BTXPWR ecce tt etc etd tae at ien na eode eeu e 37 6 2 Fan Connectors FAN CPU J28 and FAN SYS J29 0 ecccceccccceeeceeececeeeeeceeeeeseaeeeceeeseeeeseaeeesnaeenenees 38 6 3 PS 2 Keyboard and Mouse connector KBDMSE U 7 memes 39 6 4 Display connectors Internal iiri te rr tir p err su DXX REIR ola ca an a an 40 6 4 1 eDP connector EDP 338 EE 40 6 4 2 LVDS Flat Panel Connector LVDS 90 41 KTQM 77 KTHM76 Users Guide KTD N0850 F Page 5 6 5 SATA Serial ATA Disk interface J21 J26 oo eee sse nnne ren enr en tenes 42 6 6 USBConnectors USB tete ade ere dat ere tn sere ea e ere bk AEN 43 6 6 1 US
127. s F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description Disabled Enable or Disable Serial Port Enabled COM Auto IO 3E8h IRQ 7 lO 3F 8h IRQ 3 4 5 6 7 10 11 12 Select an optimal setting for Super IO 2F8h IRQ 3 4 5 6 7 10 11 12 IO device IO 3E8h IRQ 3 4 5 6 7 10 11 12 IO 2E8h IRQ 3 4 5 6 7 10 11 12 Serial Port Change Settings Note1 Standard Serial Port Mode Change the Serial Port mode Device Mode Note1 IrDA 1 0 HP SIR Mode Select High Speed or Normal ASKIR Mode mode mode Note1 only if Serial Port Enabled KTQM 77 KTHM76 Users Guide KTD N0850 F 10 2 11 4 Serial Port 4 Configuration BIOS Advanced Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced Serial Port 4 Configuration Device Settings Change Settings Device Mode Function Serial Port Change Settings Device Mode IO 2E8h IRQ 10 Auto Standard Serial Po Enable or Disable Serial Port COM lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Note1 Note1 Selection Disabled Enabled Auto IO 2E8h IRQ 10 IO 3F8h IRQ 3 4 5 6 7 10 11 12
128. size used by the Internal Graphics Device Gfx Low Power Mode Enabled Disabled This option is applicable for SSF only Graphics Performance Analyzers Enabled Disabled Enable or disable Intel Graphics Performance Analyzers Counters KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Chipset 10 3 2 1 1 LCD Control Aptio Setup Utility Copyright O 2012 American Megatrends Inc LCD Control Select the Video Device which will be activated during POST This has no effect if external LCD Panel Type VBIOS Default graphics present SDVO LFP Panel Type VBIOS Default Secondary boot display Panel Scaling Auto selection will appear based on Backlight Control PWM Inverted your selection BIA Auto VGA modes will be supported Spread Spectrum clock Chip Off only on primary display TV1 Standard VBIOS Default TV2 Standard VBIOS Default ALS Support Disabled Active LFP No LVDS Panel Color Depth 18 Bit Select Screen Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc KTQM 77 KTHM76 Users Guide KTD N0850 F Function Primary IGFX Boot Display Selection VBIOS Default CRT DVI A default 1 EFP DVI D default 1 LFP LVDS display BIOS Chipset Description Select the Video Device which will be activated during POST
129. t 1 sec 5 sec The time out value for Control Bulk and USB transfer time out 10 sec Interrupt transfers 20 sec 10 sec Device reset tim tout 20 sec USB mass storage device Start Unit command SE gu 30 sec time out 40 sec Maximum time the device will take before it Auto properly reports itself to the Host Controller Device power up delay Nonnal Auto uses default value for a Root port it is 100 ms for a Hub port the delay is taken from Hub descriptor KTQM 77 KTHM76 Users Guide KTD N0850 F Page 86 BIOS Advanced 10 2 10 Advanced SMART Settings Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced SMART Settings Run SMART Self Test on all HDDs during POST Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description Disabled Run SMART Self Test on all HDDs during SMART Self Test Enabled POST Note S M A R T Self Monitoring Analysis and Reporting Technology often written as SMART is a monitoring system for computer hard disk drives to detect and report on various indicators of reliability in the hope of anticipating failures KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Advanced 10 2 11 Advanced Super IO Configuration Aptio Setup Uti
130. te Auto BIOS auto configure Disable Disabled ASPM Disabled ASPM Support Auto Force LOs KTQM 77 KTHM 6 Users Guide KTD N0850 F Page 71 BIOS Advanced 10 2 1 2 PCI Express GEN 2 Settings Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced PCI Express GEN2 Link Register Settings If supported by hardware and set to Force to 2 5GT s for Downstream Ports this sets an upper limit on Link operational speed by restricting the values advertised by the Upstream component in its training sequences Ehen Auto is selected HW initialized data will be used lt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 15 1226 Copyright 2012 American Megatrends Inc Function Selection Description If supported by hardware and set to Force to 2 5GT s for Downstream Ports this sets an Auto upper limit on Link operational speed by Target Link Speed Force to 2 5GT s restricting the values advertised by the Force to 5 0GT s Upstream component in its training sequences Ehen Auto is selected HW initialized data will be used KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Advanced 10 2 2 Advanced APCI Settings Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced ACPI Settings Enable Hi
131. ted frame rate some 1920x1200 Signal Description LVDS Flat Panel Connector Signal LVDS AO A3 Description LVDS A Channel data LVDS ACLK LVDS A Channel clock LVDS BO Bi LVDS B Channel data LVDS BCLK LVDS B Channel clock BKLTCTL Backlight control 1 PWM signal to implement voltage in the range 0 3 3V BKLTEN Backlight Enable signal active low 2 VDD ENABLE Output Display Enable LCDVCC VCC supply to the display Power on off sequencing depending on selected in BIOS setup display type 5V or 3 3V selected in BIOS setup LCDVCC is shared with eDP connector Maximum load is 1A at both voltages DDC CLK DDC Channel Clock Notes Windows API will be available to operate the BKLTCTL signal Some Inverters have a limited voltage range 0 2 5V for this signal If voltage is gt 2 5V the Inverter might latch up Some Inverters generates noise on the BKLTCTL signal resulting in making the LVDS transmission failing corrupted picture on the display By adding a 1Kohm resistor in series with this signal mounted in the Inverter end of the cable kit the noise is limited and the picture is stable If the Backlight Enable is required to be active high then check the following BIOS Chipset setting Backlight Signal Inversion Enabled KTQM 77 KTHM76 Users Guide KTD NO850 F Page 42 Internal Connectors 6 5 SATA Serial ATA Disk interface J21 J26
132. used to deactivate external system PWR OK PoWeR OK signal is high if no power failures are detected This is not the same as the P_OK signal generated by ATX PSU EXTernal BATtery option for connecting terminal of an external primary cell battery EXT_BAT 2 5 4 0 V terminal connected to GND The external battery is protected against charging and can be used with without the on board battery installed FAN30UT FAN 3 speed control OUTput 3 3V PWM signal can be used as Fan control voltage FANSIN FAN3 Input OV to 3V3 amplitude Fan 3 tachometer input FANAOUT FAN 4 speed control OUTput 3 3V PWM signal can be used as Fan control voltage FANAIN FANA Input OV to 3V3 amplitude Fan 3 tachometer input SB3V3 Max load is 0 75A 1 5A 1 sec SB5V StandBy 5V supply GPIOO 47 General Purpose Inputs Output These Signals may be controlled or monitored S through the use of the KT API V2 Application Programming Interface EGCLK Extend GPIO Clock signal EGAD Extend GPIO Address Data signal EGCS Extend GPIO Chip Select signal active low TMAO Timer Output 12V Max load is 0 75A 1 5A lt 1 sec Available Temperature Sensor cable kit for System Fan Temperature Cruise selected in BIOS Based on Maxim DS18B20 Accurate to 0 5 C over the range of 10 C to 85 C Feature connector 3 3V Pin 9 GND Pin 19 and GPIO16 Pin 29 PN1053 4925 Cable Temperature Sensor 44
133. ve Enable or Disable SATA Port Hot Plug see same function above see same function above External SATA see same function above see same function above Spin Up Device see same function above see same function above Port4 Disabled Enabled Enable or Disable SATA Port Hot Plug see same function above see same function above External SATA see same function above see same function above Spin Up Device Hot Plug see same function above Disabled Enabled see same function above see same function above Enable or Disable SATA Port see same function above External SATA see same function above see same function above Spin Up Device see same function above see same function above KTQM 77 KTHM76 Users Guide KTD N0850 F BIOS Advanced 10 2 6 Advanced Intel TXT LT Configuration Intel TXT LT Configuration is only present when using KTQM77 mITX Aptio Setup Utility Copyright 2012 American Megatrends Inc Advanced Intel Trusted Execution Technology Configuration Enables or Disables Intel TXT LT support Intel TXT support only can be enabled disabled if SMX is enabled VT and VT d support must also be enabled prior to TXT Secure Mode Extensions SMX Enabled lt Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Prev
134. w wakeup on USB device activity Protected by resettable 1A fuse covering both USB ports 5V SB5V KTQM 77 KTHM76 Users Guide KTD N0850 F IO Area Connectors 5 4 Audio Connector IO Area The on board Audio circuit implements 7 1 2 Channel High Definition Audio with UAA Universal Audio Architecture featuring five 24 bit stereo DACs and three 20 bit stereo ADCs The Following Audio connector is available in IO Area Audio Speakers Line in and Microphone are available in the stacked audiojack connector TIP LINEHL A RING LINER A SLEEVE GND Gr TIP FRONT OUT L OA RING J FRONT OUT R OA SLEEVE GND PWR MIC1 L WI MIC1 R A GND PWR Description FRONT OUT L Front Speakers Speaker Out Left FRONT OUT R Front Speakers Speaker Out Right MIC1 L Microphone 1 Left Shared with Audio Header MIC1 R Microphone 1 Right Shared with Audio Header LINE1 L Line 1 signal Left Shared with Audio Header LINE1 R Line 1 signal Right Shared with Audio Header KTQM 77 KTHM76 Users Guide KTD N0850 F Internal Connectors 6 Internal Connectors 6 1 Power Connector ATX BTXPWR The KTQM77 boards are designed to be supplied from a standard ATX or BTX power supply Alternatively supplied by single 12V 5 Use of BTX supply is not required for operation but may be required to drive high power PCle c

KTQM77/mITX – KTHM76/mITX Users Guide

Contents

Download Pdf Manuals

Related Search

Related Contents

KTQM77/mITX &ndash; KTHM76/mITX Users Guide

Contents

Download Pdf Manuals

Related Search

Related Contents

KTQM77/mITX – KTHM76/mITX Users Guide