PWS Summit Series User Manual
Contents
1. ADJUSTING THE SEAR There are two set screws on the bottom of the trigger that control sear adjustment To increase sear engagement you must first loosen the rear screw followed by tightening of the front screw Decreasing sear engagement and reducing take up is accomplished by loosening the front screw and then tightening the rear screw It is very important to not that these set screws only need to be moved a fraction of a turn for noticeable results Use the window to watch your progress and snug both screws when finished 18 ASSEMBLING AND DISASSEMBLING THE BARRELED ACTION ASSEMBLING BARRELED ACTION Place the designated spacer shims on the barrel Fig 1 Place the barrel into the action aligning the V Block with the notch on the barrel Push the barrel in as far as it will go Using a hand torch heat up the action while applying downward pressure on the barrel until it falls into place Fig 2 Tighten the V Block screws until the barrel is firmly held in place TR REMOVING THE BARREL 1 Remove the two V Block screws 2 Hold the barreled action upright with the action facing down 3 Using a dead blow hammer grip the barrel firmly and strike down on the action until the barrel comes free It may be necessary to use the blow torch to heat up the action before using the deadblow hammer Fig 3 Fig 1 Fig 2 Fig 3 19 MAGAZINE INSPECTION AND CARE MAGAZINE INSPECTION AND CARE Check the magazine frequentl2. The use of a locking device or safety lock is only one aspect of responsible firearms storage For increased safety firearms should be stored unloaded and locked in a location that is both separate from their ammunition and inaccessible to children and other unauthorized persons North Carolina It is unlawful to store or leave a firearm that can be discharged in a manner that a reasonable person should know is accessible to a minor Texas It is unlawful to store transport or abandon an unsecured firearm in a place where children are likely to be and can obtain access to the firearm Wisconsin If you leave a loaded firearm within the reach or easy access of a child you may be fined or imprisoned or both if the child improperly discharges possesses or exhibits the firearm PLEASE CHECK WITH YOUR LICENSED RETAILER OR STATE POLICE FOR ADDITIONAL WARNINGS WHICH MAY BE REQUIRED BY LOCAL LAW OR REGULATION SUCH REGULATIONS CHANGE CONSTANTLY AND LOCAL AUTHORITIES ARE IN THE BEST POSITION TO ADVISE YOU ON SUCH LEGAL MATTERS LOCKING DEVICE INSTALLATION INSTRUCTIONS USE OF LOCKING DEVICES 1 Always keep your firearm pointed in a safe direction including when you are installing or removing your locking device 2 Always verify that your firearm is completely unloaded before installing your locking device 3 Do not install locking devices in the trigger guard always keep your fingers and locking device outside the trigger gu
3. Barrel Mounting Bolts Ruger Part pf Barrel Block E E A Barrel Shims S E M A O B SummitTension Barrel ta Summit Barrel Thread Protector OOOO p15 St Mounting Screw Ruger Part p16 Ruger t0 22Magazine Ruger Part 17 Rear Lever Bushing Tension Washer OO 38 ever Bushing E E pea ever Bushing Screw o o o 20 Bolt Removal BufferPin oo o o A Hammer Spring O p22 Hammer Pin LB Firing Pin Retaining Pin A ge Group Mounting Pin OOOO 21 EXPLODED VIEWS AND PART NUMBERS continued DISCRIPTION PART NUMBER O 5 Hammer O S p26 Trigger e 27 SearEngagement Screw gt gt gt A SearSpring Buffer a Over TravelandSafetyScrews E eee O A SearBushing O A E O A ET A O E p35 EAT O p86 ETT O A E O E A O Ll 39 RugerTriggle Group Complete RugerPart Ll do Summit Extended Magazine Release 22222 A TT O o THIS PAGE INTENTIONALLY LEFT BLANK 29 WARRANTY INFORMATION PWS LIMITED WARRANTY This product is warranted to be free of defects in material and workmanship for a period of 2 years from the date of purchase At Primary Weapons Systems option the defective product will be repaired replaced or substituted with a product of equal value For warranty service call Primary Weapons Systems at 208 344 5217 extension 8 PRIMARY WEAPONS SYSTEMS INC SHALL IN NO EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES Some states do not allow the exclusion or limitation of incidental or consequential damages s
4. STANDARD OR REMANUFACTURED OR HAND LOADED RELOADED AMMUNITION OR OF CARTRIDGES OTHER THAN THOSE FOR WHICH THE FIREARM WAS ORIGINAL CHAMBERED 11 MAGAZINE LOADING THE MAGAZINE To load the magazine press the rim of the cartridge against the magazine rotor at the widest section of the magazine throat until the car tridge enters far enough to be pushed to the rear end of the magazine Each succeeding cartridge is pressed against the body of the top cartridge and slid to the rear of the magazine until a maximum of ten 10 22 LR cartridges are in the magazine LOAD AND FIRE WITH MAGAZINE 1 2 3 a 12 Keep the muzzle pointed in a safe direction Pull the bolt handle rearward Check the chamber to be certain it is empty Engage the safety Remove the magazine by using your index finger to push forward on the magazine release and at the same time grasp the magazine between thumb and forefinger of the other hand to draw it out of the magazine well Load the magazine with the appropriate amount of cartridges Insert magazine into the firearm with bullet end of the cartridges toward the muzzle Load a cartridge into the chamber by cycling the action DO NOT TOUCH THE TRIGGER If a cartridge does not readily chamber eject it from the rifle and remove the magazine The rifle is now fully loaded IF THE RIFLE IS NOT TO BE FIRED IMMEDIATELY THE SAFETY SHOULD REMAIN ON The action needs to be manually cycled after each s
5. THE SAFETY FULLY TO ITS INTENDED POSITION AND CHECK IT THE SAFETY IS NOT ON UNLESS IT IS COMPLETELY ON NEVER DEPEND ON A SAFETY MECHANISM OR ANY OTHER MECHANICAL DEVICE TO JUSTIFY CARELESS HANDLING OR PERMITTING THE RIFLE TO POINT IN AN UNSAFE DIRECTION THE ONLY SAFE RIFLE IS ONE IN WHICH THE BOLT IS OPEN THE CHAMBER EMPTY AND THERE IS NO MAGAZINE IN THE GUN 10 AMMUNITION WARNING AMMUNITION DISCHARGING FIREARMS IN POORLY VENTILATED AREAS CLEANING FIREARMS OR HANDLING AMMUNITION MAY RESULT IN EXPOSURE TO LEAD AND OTHER SUBSTANCES KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS REPRODUCTIVE HARM AND OTHER SERIOUS PHYSICAL INJURY HAVE ADEQUATE VENTILATION AT ALL TIMES WASH HANDS THOROUGHLY AFTER EXPOSURE AMMUNITION The PWS Summit 10 22 rifles are chambered for and designed to properly function with only the 22 caliber Long Rifle rimfire cartridge stan dard high velocity manufactured to U S industry standards Do not use 22 short 22 long 22 shot or 22 cartridges loaded with blunt nosed sharp shouldered or explosive bullets They will not func tion reliably and may jam the mechanism or discharge before being fully chambered Use only ammunition that functions correctly in your rifle AMMUNITION CARTIRDGES NOTICE WE SPECIFICALLY DISCLAIM RESPONSIBILITY FOR ANY DAMAGE OR INJURY WHATSOEVER OCCURRING IN CONNECTION WITH OR AS A RESULT OF THE USE IN ANY PWS FIREARMS OF FAULTY OR NON
6. muzzle is pointed in a safe direction and the safety is on If possible first remove the magazine It may be necessary to manually remove a jammed cartridge which has only partially been stripped from the magazine If so use extreme care Pull the bolt handle rearward Drawing the bolt fully to the rear may bring the jammed cartridge along When attempting to clear a jam use only wood tools so that a cartridge will not be ignited if you strike a primer and so that the chamber and magazine will not be damaged A 3 16 wood dowel rod with a point on one end is useful Visually check to make sure all cartridges have been removed from the rifle Safely dispose of any cartridges involved in a malfunction incident Do not use damaged ammunition in any firearm MINIMIZING MALFUNCTIONS MINIMIZING MALFUNCTIONS Most malfunctions are caused by improper or damaged magazines incorrect ammunition or poor maintenance 1 If it appears that the gun and magazine are not at fault and that the jam was caused by the type of cartridge being used then try an other type 2 If changing to another type or brand of cartridges does not at once eliminate malfunctioning then the following steps should be taken a b N Make certain the gun and the magazine are unloaded and that the safety is on Thoroughly clean the magazine and bolt mechanism paying particular attention to removing accumulated grease Use a bristle brush and solvent
7. pin indents the cartridge case rim and ignites the priming compound inside the rim This ignites the powder in the cartridge case and a great volume of gas is instantly generated which acts on the interior of the cartridge case in all directions Because the bullet offers the least resistance it moves out of the cartridge case and exits the muzzle The bolt then moves rearward automatically extracting and ejecting the fired cartridge case and at the same time cocking the hammer and compressing the recoil spring etc as described above Once the trigger is released the rifle is ready to fire again Each time the trigger is pulled and released the same cycle is repeated until there are no more cartridges in the magazine or in the chamber WARNING THE RIFLE WILL FIRE IF THERE IS A CARTRIDGE IN THE CHAMBER AND THE TRIGGER IS PULLED WHETHER OR NOT THERE IS A MAGAZINE IN PLACE REMOVING THE MAGAZINE DOES NOT UNLOAD THE RIFLE NEVER ASSUME THE RIFLE IS UNLOADED VISUALLY INSPECT THE CHAMBER AND THE MAGAZINE EACH TIME THE RIFLE IS HANDLED TO BE CERTAIN THERE ARE NO CARTRIDGES IN EITHER CONTROLS AND KEY COMPONENTS Summit 10 22 Rifle Receiver ger ne ousing Barrel CONTROLS AND KEY COMPONENTS CONTINUED Summit 10 22 Rifle Bolt Handle SafetySwitch Trigger Summit Magazine Release Magazine Take Down Screw OPERATION OF SAFETY OPERATION OF SAFETY The PWS Summit rifles have a cross button safety which is located in the forw
8. to remove grease and fouling from the bolt face the extractor the chamber and the feed ramp Check to see that the magazine rotor spring tension is adequate Check the magazine throat to be certain they are free of nicks and burrs and are not deformed Remove excess oil and solvent from all cleaned components load the magazine and try the firearm again If the above procedures do not result in a smooth and reliably functioning firearm do not use the gun please contact Primary Weapons Systems for servicing WARNING MALFUNCTIONS THE 22 LONG RIFLE RIMFIRE CARTRIDGES FIRE WHEN THE FIRING PIN IMPACTS THE RELATIVELY SOFT CARTRIDGE CASE RIM AND ALSO CAN BE DISCHARGED BEFORE IT IS CHAMBERED IF ITS RIM RECEIVES A SHARP BLOW IF A CARTRIDGE HANGS UP JAMS OR BINDS WHEN BEING CHAMBERED OR WHEN BEING FED FROM THE MAGAZINE INTO THE CHAMBER DO NOT ATTEMPT TO FORCE IT INTO THE CHAMBER BY PUSHING OR STRIKING THE BOLT 15 DISASSEMBLY DISASSEMBLING THE RIFLE 1 Loosen don t remove the takedown screw Fig 1 2 Position the safety so an equal amount of the button is exposed on each side If the safety is not in the middle when the barrel receiver assembly is lifted out of the stock the stock will be damaged Fig 2 3 Swing the barrel receiver assembly upward away from the forearm of the stock Be careful the two receiver cross pins and bolt stop pin do not fall out Fig 3 4 Remove the trigger guard by simply drifting out the
9. two receiver pins It is recommended that the components of the trigger guard as sembly not be disassembled from the trigger guard Fig 4 This is the extent of disassembly required for routing inspection cleaning and lubrication If it is desired to thoroughly clean the inside of the receiver by removing the bolt be aware that although removing and installing the bolt along with the bolt handle recoil spring assembly is simple it must be done correctly For instructions on removing the bolt please see the next page Fig 1 Fig 2 Fig 3 Fig 4 16 REMOVING THE BOLT REMOVING THE BOLT 1 Disassemble rifle using steps 1 4 on the previous page 2 Remove the buffer tube Fig 1 3 Pull the bolt rearwards Fig 2 4 Turn the action upside down allowing the bolt to gently fall out Fig 3 Fig 2 Fig 3 17 REMOVING THE FIRING PIN AND ADJUSTING THE SEAR REMOVING THE FIRING PIN 1 Remove the cross pin from the rear of the bolt Fig 1 2 Slide firing pin out keeping careful track of the tapered spring that slides over the pin Fig 2 INSERTING THE FIRING PIN Inserting the firing pin is accomplished by revering the order of the previous steps Make careful note when putting the tapered spring back on the firing pin that the small end is against the pin Fig 3 If you have removed the secondary extractor make sure to insert the spring and plunger before reattatching the extractor Fig 4 Fig 1 Fig 2 Fig 3 Fig 4
10. ASE OR ANY OTHER MATERIAL EVEN PARTIALLY OBSTRUCTING THE BORE MAY RESULT IN DAMAGE TO THE RIFLE AND SERIOUS INJURY TO THE SHOOTER AND THOSE NEARBY DO NOT SPRAY OR APPLY LUBRICANTS DIRECTLY ON AMMUNITION 21 STAINLESS STEEL OVERVIEW OVERVIEW Firearms and components made of stainless steel are relatively more resistant to corrosion than those of blued steel However in the interest of proper operation and long life of a stainless steel firearm inspect it frequently and clean lubricate and apply an appropriate rust preventative Sometimes discoloration occurs from perspiration or from contact with some types of gun cases Rusting may occur as a result of the firearm being exposed to moisture salt air or chemicals Minor discoloration can usually be removed by rubbing the stainless area with an abrasive ink eraser crocus cloth or a metal polishing com pound When using any of these abrasives proceed with care and use light pressure to achieve a blending of color with those areas that are not discolored Do NOT use abrasives on the clear coated of the aluminum alloy receiver and trigger housing External Surfaces most subject to rusting from handling or from exposure to the elements should be cleaned and wiped dry after use or af ter exposure to adverse conditions If the rifle is to be stored coat it with a light film of oil or preservative Where the rifle is in continuing use and the presence of oil or grease would be objec
11. NG Children can operate firearms which may cause death or serious injury It is a crime to store or leave a loaded firearm in any location where an individual knew or should have known that an unsupervised minor would gain access to the firearm Store your firearm responsibly STATE BY STATE WARNINGS CONTINUED Massachusetts This handgun is not equipped with a device that fully blocks use by unauthorized users More than 2000 000 firearms like this one are stolen from their owners every year in the United States IN addition there are more than a thousand suicides each year by younger children and teenagers who get access to firearms Hundreds more die from accidental discharge It is likely that many more children sustain serious wounds or inflict such wounds accidentally on others In order to limit the chance of such misuse it is imperative that you keep this weapon locked in a secure place and take other steps necessary to limit the possibility of theft or accident Failure to take reasonable preventative steps may result in innocent lives being lost and in some circumstances may result in your liability for those deaths It is unlawful to store or keep a firearm rifle shotgun or machine gun in any place unless that weapon is equipped with a tamper resistant safety device or is stored or kept in a securely locked container New Jersey It is a criminal offense to leave a loaded firearm within easy access of a minor New York City
12. ON 20 CARE AND CLEANING CLEANING THE RIFLE Cleanliness is important to the function of this firearm Use commercially available bore cleaning solution and a brass brush followed by dry ing with a cloth patch to remove any powder residue 1 Disassemble the rifle to the extent described on page 16 2 Using a cleaning rod run a solvent wetted patch through the bore several times then attach a solvent wetted bristle brush to the road and run it back and fort the full length of the bore as many times as necessary to remove grease and dirt from the bore and chamber Clean the bore with dry patches and examine Bore fouling can contribute to reduced accuracy and grease accumulation in the chamber can interfere with proper feeding of the cartridges 3 Using powder solvent on a clean patch or bristle brush remove powder residue from all components of the mechanism After clean ing run a dry patch through the bore then follow with a patch that is very lightly oiled Wipe all surfaces clean with cloth then wipe all surfaces clean with a cloth then wipe all surfaces with a patch or cloth that has been very lightly oiled Only a light application of oil is needed to provide adequate lubrication of moving parts and to prevent rust Excess accumulations of oil tend to attract particles of dust and dirt and may congeal in gold weather which can interfere with the safe and reliable functioning of the rifle WARNING FIRING A RIFLE WITH OIL GRE
13. PWS Summit Series User Manual ver 100110 TM 9 PWS SS STATE BY STATE WARNINGS STATE BY STATE WARNINGS Certain states require by law that their own specified warning notices be conspicuously included by the manufacturer distributor or retail dealer with firearms sold in that state Primary Weapons Systems sells its products in compliance with applicable laws and regulations Because our products may be sold in these states we include the following California Children are attracted to and can operate firearms that can cause severe injuries or death Prevent child access by always keeping guns locked away and unloaded when not in use If you keep a loaded firearm where a child obtains and improperly uses it you may be fined or sent to prison Connecticut Unlawful storage of a loaded firearm may result in imprisonment or fine Florida It is unlawful and punishable by imprisonment and fine for any adult to store or leave a firearm in any place within the reach or easy access of a minor under 18 years of age or to knowingly sell or otherwise transfer ownership or possession of a firearm to a minor or a person of unsound mind Maine Endangering the welfare of a child is a crime If you leave a firearm and ammunition within easy access of a child you may be subject to fine imprisonment or both Keep firearms and am munition separate Keep firearms and ammunition locked up Use trigger locks Maryland WARNI
14. ard during device installation and removal 4 Store firearms ammunition and keys separately and securely away from children and careless adults do not store your firearm with the keys in the locking device 5 Do not attempt to work the action of your firearm with the locking device in place this may damage your firearm 6 While locking devices are an important aid to security measures they are not a substitute for safe firearm handling and proper storage Remember that any mechanical device can be bypassed with enough time knowledge determination and equipment WARNING FIREARMS SAFETY YOUR RESPONSIBILITY Safety must be the first and constant consideration of every person who handles firearms and ammunition This Instruction Manual is designed to assist you in learning how to use and care for your PWS Summit 10 22 rifles properly Please contact us if you have any questions about it Only when you are certain you fully understand the Manual and can properly carry out its instructions should you practice loading etc with live ammunition If you have any doubts about your ability to handle or use a particular type of gun safely then you should seek supervised instruction Such personalized instruction is often available from gun dealers gun clubs or police departments If none of these sources can help you write to the National Rifle Association 11250 Waples Mill Road Fairfax VA 22030 7400 They will assist you The person poss
15. ard portion of the trigger guard The safety can only be oper ated when the hammer is cocked The safety is on when it protrudes fully from the right side the bolt handle side of the trigger guard assembly In this position the sear is blocked and the gun cannot be fired from a normal pull on the trigger THE SAFETY SHOULD ALWAYS BE IN THE ON SAFE POSITION EXCEPT WHEN THE SHOOTER IS ACTUALLY FIRING THE GUN THE SAFETY SHOULD BE MOVED TO THE ON POSITION WHENEVER THE SHOOTER CEASES FIRING EVEN TEMPORARILY The safety is off fire when it protrudes from the left side of the trigger guard assembly When the safety is off the red band shows on the safety button Do not totally rely on the appearance of the red band to indicate that the safety is off In poor light or if dirt is present the red band may not be visible IF THE SAFETY IS OFF AND THE TRIGGER IS PULLED THE RIFLE WILL FIRE The safety is held in its on or off position by a plunger that is under spring tension When the safety is moved to either the on or off posi tion a distinct click should be heard Frequently check the position of the safety to be certain the safety has not been inadvertently moved If the safety seems to move too easily or if the click is not heard when the safety is moved stop using the rifle and contact Primary Weapons Systems for repair WARNING KEEP THE SAFETY ON UNLESS ACTUALLY FIRING ALWAYS MOVE
16. essing a gun has a full time job You cannot guess you cannot forget You must know how to use your firearm safely DO NOT USE ANY FIREARM WITHOUT HAVING A COMPLETE UNDERSTANDING OF ITS PARTICULAR CHARACTERISTICS AND SAFE USE Remember There is no such thing as a foolproof gun TABLE OF CONTENTS INTRODUCTION State By State Warnings 2 Use of Locking Devices 4 Installing the Locking Device 4 Firearms Safety 5 Table Of Contents 2 6 6 4 20 6 sde 8 0 ae OS 6 General Information 7 CONTROLS AND KEY COMPONENTS Summit Series Controls and Key Components 8 SAFETY Operation of Safety 10 AMMUNIION 4 ton 25 ae PAYEE ADS RSLS oR oo 11 Loading the Magazine 12 LOADING UNLOADING Load and Fire with magazine 12 Load and Fire without magazine 13 Unloading esa sen arte oo eo Se 13 EXTRACTING AND EJECTING Extracting and Ejecting a Chambered Cartridge 14 Clearing a Malfunction 14 Minimizing Malfunctions 15 DO NOT OPERATE YOUR PWS RIFLE PRIOR TO READING THIS MANUAL DISASSEMBLY REASSEMBLY Disassembling the Rifle 16 Removing the Bolt 17 Removing the Firin
17. g Pin and Adjusting the Sear 18 Assembling a Barreled Action 19 Removing the Barrel 19 CLEANING AND INSPECTION Magazine Inspection and Cleaning 20 Cleaning the Rifle 21 MAINTENANCE OF STAINLESS STEEL RIFLES Overview 22 BASIC RULES OF SAFE FIREARMS HANDLING Basic Rules of Safe Firearms Handling 23 NATIONAL FIREARMS ACT WARNING ALL NFA Rules Apply 25 The National Firearms Act 25 Criminal Penalties for NFA Violations 25 EXPLODED VIEW AND PART NUMBERS Exploded View and Part Numbers 26 WARRANTY Warranty Information 30 Warranty Return Procedures 31 GENERAL INFORMATION amp MECHANICAL CHARACTERISTICS GENERAL INFORMATION The PWS Summit 10 22 rifles are toggle action rifles Retracting the bolt handle cocks the internal hammer and compresses the recoil spring When the bolt is manually released it moves forward driven by the recoil spring trips a cartridge from the magazine if a loaded magazine is in place and chambers the cartridge The bolt is held against the chambered cartridge by the recoil spring When the trigger is pulled the hammer is released and strikes the firing pin The firing
18. hot to load the next round until the magazine is empty or you are done firing The safety should be moved to the on position as soon as firing is completed and it should be on at all times except when the rifle is on target and being fired WARNING FIRING KEEP FACE AND HANDS AWAY FROM THE BOLT HOT BRASS IS EJECTED QUICKLY AND CAN BURN YOU LOADING UNLOADING LOAD AND FIRE WITHOUT MAGAZINE The rifle can be used as a single shot rifle in the absence of a magazine or for safety or training purposes To do so follow step 1 p 13 Then load a cartridge into the chamber and follow steps 6 and 7 p 13 disregarding the magazine Engage the safety between shots WARNING UNLOADING SO THAT THE RIFLE CAN BE USED AS A SINGLE LOADER IT WILL FIRE WHETHER OR NOT A MAGAZINE IS IN THE GUN IF A CARTRIDGE IS CHAMBERED REMOVING THE MAGAZINE DOES NOT UNLOAD THE RIFLE THE SAFETY SHOULD ALWAYS BE IN THE ON SAFE POSITION WHEN LOADING OR UNLOADING THE RIFLE UNLOADING 1 Keep the muzzle pointed in a safe direction 2 Remove the magazine 3 Retract the bolt to its open position This should eject any cartridge in the chamber 4 Cartridges can be removed from the magazine by simply pushing them lightly downward and forward with the thumb forefinger or the rubber eraser end of a pencil against the rim of the top cartridge 5 With the muzzle pointed in a safe direction push the safety to the off position and pull the t
19. if the return was covered under warranty Remove any accessories scope scope mount sling sights bipods cleaning equipment etc that do not pertain to your problems before you send the firearm in PWS will not be responsible for lost or damaged accessories sent with returned rifles or uppers If you have any functional problem with the firearm do send the magazines with it Firearms that you wish to return for warranty or out of warranty repair may be returned directly to PWS Non warranty repairs will be billed at PWS shop rates as will work on firearms submitted with no warranty problem existing 31 PWS 800 E Citation Court Suite A Boise ID 83716 208 344 5217 www primaryweapons com
20. ise tax on the manufacture and transfer of certain firearms and mandates the registration of those firearms The Act was passed shortly after the repeal of Prohibition The NFA is also referred to as Title II of the federal firearms laws The Gun Control Act of 1968 GCA is Title I All transfers of ownership of registered NFA firearms must be done through the federal NFA registry The NFA also requires that transport of NFA firearms across state lines by the owner must be reported to the ATF CRIMINAL PENALTIES VIOLATIONS Violations of the Act are punishable by up to 10 years in federal prison and forfeiture of all devices or firearms in violation and the individual s right to own or possess firearms in the future The Act provides for a penalty of 10 000 for certain violations A willful attempt to evade or defeat a tax imposed by the Act is a felony punishable by up to five years in prison and a 100 000 fine 500 000 in the case of a corporation or trust under the general tax evasion statute For an individual the felony fine of 100 000 for tax evasion could also be imposed 25 EXPLODED VIEWS AND PART NUMBERS 26 EXPLODED VIEWS AND PART NUMBERS continued DISCRIPTION PART NUMBER 01 Bolt Guide Rail Mounting Screws S S S 02 Summit ReceiverHousing ooo o S y kn o VE A E E pS O E o p06 Front ever O e p07 Weak SideExtractorSpring 08 Weak side Extractor Detent ooo o e A Weak Side Extractor O i 10
21. o the above exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which may vary from state to state Primary Weapons Systems Inc will not be responsible for damage of your firearm caused by Failure to provide proper care and maintenance Accidents abuse or misuse Barrel obstruction Hand loaded reloaded or improper ammunition Unauthorized adjustments repairs or modifications Use of ammo that does not fall within the parameters set by SAAMI Normal wear and tear Before seeking warranty service please refer to the troubleshooting guide in this manual to attempt to solve the problem Perform all instructed maintenance and assure that ammunition and magazines are correct and in good condition Shop rates plus the cost of return shipping will be applied if no covered defect is found 30 WARRANTY RETURN PROCEDURES Returns for any reason will NOT be accepted without a Return Merchandise Authorization RMA number issued by PWS Please call 208 344 5217 extension 8 to receive your RMA number After you receive your RMA number print it on the outside of the box and include a copy of the RMA paperwork that you receive from PWS Send your item and completed RMA request to PWS Attn Warranty Service 800 E Citation Court Suite A Boise ID 83716 Shipping to and from PWS is the owner s responsibility except that PWS will return the firearm to the customer shipping prepaid
22. otectors when shooting Exposure to shooting noise can dam age hearing and adequate eye protection when shooting is essential 8 NEVER CLIMB A TREE OR FENCE WITH A LOADED FIREARM Put the firearm down carefully before climbing a fence and unload it before climbing or descending a tree or jumping over a ditch or other obstructions Never pull or push a loaded firearm toward yourself or others 9 NEVER TRANSPORT A LOADED FIREARM Firearms should always be unloaded before being placed in a vehicle A suitable carrying case should be used to transport your firearm 10 AVOID ALCOHOLIC BEVERAGE WHEN SHOOTING Don t drink until the day s shooting is over Handling firearms while under the influence of alcohol or medications that could affect your judgement or coordination constitutes a criminal disregard for the safety of others Do not handle or use firearms while taking any drugs or medication which may impair your ability to act safely 24 NATIONAL FIREARMS ACT WARNINGS ALL NFA RULES APPLY Regarding ownership of any firearm the buyer has complete responsibility to ensure he she is in full compliance with all applicable local state and federal laws regarding possession of said firearm s THE NATIONAL FIREARMS ACT The National Firearms Act NFA 73rd Congress Sess 2 ch 757 48 Stat 1236 enacted on 26 June 1934 currently codified and amended as 26 U S C ch 53 is an Act of Congress that in general imposes a statutory exc
23. rigger to de cock it The rifle can be dry fired for practice as long as it is empty and pointed in a safe direction 6 Push the empty unloaded magazine into the rifle until the catch locks it in place ALWAYS VISUALLY DOUBLE CHECK THE CHAMBER TO BE CERTAIN IT IS EMPTY THE ONLY SAFE RIFLE IS ONE IN WHICH THE BOLT IS OPEN AND THE CHAMBER AND MAGAZINE ARE EMPTY 13 EXTRACTING AND EJECTING EXTRACTING AND EJECTING A CHAMBERED CARTRIDGE When the bolt is operated by hand there can be a failure to extract the cartridge from the chamber or a failure to eject the cartridge clear of the rifle These failures usually are the result of the bolt not being pulled rearward vigorously coupled with an accumulation of bullet lubri cant in the chamber From the foregoing it is clear that the gun user must 1 Always visually check the chamber after opening the bolt to eject achambered cartridge If the bolt is not vigorously retracted when be ing operated by hand the extracted cartridge can be ejected into the magazine area instead of outside the rifle Thoroughly clean the chamber and the extractor as often as necessary to prevent the accumulation of grease and dirt If an empty magazine is in the rifle when the bolt is being hand retracted to extract a cartridge the cartridge may drop on top of the magazine Then when the bolt goes forward the cartridge will be chambered again CLEARING MALFUNCTION 14 Be certain the
24. s racks or cabinets or by using the locking device supplied with the firearm when not in use Ammunition should be safely stored separate from your firearms Store your firearms out of sight of visitors and children It is the gun owner s responsibil ity to be certain that children and persons unfamiliar with firearms cannot gain access to firearms ammunition or components 4 BE SURE THE BARREL IS CLEAR OF OBSTRUCTIONS BEFORE SHOOTING Even a bit of mud snow or excess lubricated oil or grease in the bore may cause the barrel to bulge or even burst on firing and can cause serious injury to the shooter and bystanders Be sure that you are using ammunition of the proper caliber and loading for the gun you are using 5 DON T SHOOT AT A HARD SURFACE OR AT WATER Bullets can glance of many surfaces like rocks or the surface of water and travel in unpredictable directions with considerable velocity 23 BASIC RULES OF SAFE FIREARMS HANDLING continued 6 BE SURE OF YOUR TARGET BEFORE YOU SHOOT Don t shoot unless you know exactly where your bullet is going to strike Be sure of the bullet stop behind your target even when dry firing with an unloaded gun If you are in the field hunting do not fire at a movement or noise Take the time to be absolutely certain of your target before you pull the trigger 7 WEAR SHOOTING GLASSES AND HEARING PROTECTORS WHEN YOU SHOOT All shooters should wear protective shooting glasses and adequate hearing pr
25. tionable then the external surfaces can be coated after cleaning and drying with a paste wax formulated for use on metals Apply the wax sparingly allow time for it to dry hard then buff lighting with a soft cloth When applying the wax take care that it does not get into the mechanism or on the functioning parts or in the bore 22 BASIC RULES OF SAFE FIREARMS HANDLING 1 LEARN THE MECHANICAL AND HANDLING CHARACTERISTICS OF THE FIREARM YOU ARE USING Not all firearms are the same The method of carrying and handling firearms varies in accordance with the mechanical provisions for avoiding accidental discharge and the various proper procedures for loading and unloading No person should handle any firearm without first having thoroughly familiarized himself with the particular type of firearm he is using and with safe gun handling in general 2 ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION Be sure of the bullet stop behind your target even when dry firing Never let the muzzle of a firearm point at any part of your body or at another person This is particularly important when loading or unloading a firearm In the vent of an accidental discharge no injury can occur as long as the muzzle is pointing in a safe direction 3 FIREARMS SHOULD BE UNLOADED WHEN NOT IN USE Firearms should be loaded only when you are in the field or on a target range or shooting area ready to shoot Firearms and ammunition should be securely locked in safe
26. y The rotor must move freely and have adequate tension so that each cartridge is quickly raised to the feed ing position At the time of manufacture proper rotor tension is set by rotation the magazine cap nut until the rotor stops turning The nut is then turned an addition 1 1 4 turns beyond the stop position To test the rotor tension load one cartridge into the magazine and then firmly press against the side of the cartridge case Remove your finger quickly The cartridge should instantly and fully move in to the feeding position If it does not the magazine should be cleaned IF CLEANING DOES NOT RESTORE PROPER ROTOR TENSION DO NOT USE THE MAGAZINE When cleaning is necessary use a solvent that will not rust the metal components or adversely affect the plastic magazine box After the magazine has been soaked in solvent to loosen foreign matter be certain to shake it vigorously with the loading opened away from you to remove solvent or residue from within the magazine After cleaning always check to be certain that the rotor movement and tension are correct and that no solvent or debris remain Do not disassemble the magazine Improper reassembly of improper tensioning of the rotor spring can cause a potentially dangerous malfunction If you experience a problem with the magazine don t use it Get a new one WARNING DAMAGED NON STANDARD OR IMPROPERLY ASSEMBLED MAGAZINES SHOULD NOT BE USED THEY CAN CAUSE THE RIFLE TO MALFUNCTI
Download Pdf Manuals
Related Search