IK Multimedia T-RackS 3 Deluxe
Contents
1. the standalone version of T RackS adds some T RackS project handling capabilities and audio hardware interface settings These are mostly what you d expect i e the ability to load and save projects and select audio drivers and control some important settings such as buffer size One area that warrants special consideration though is setting up the T RackS project properties These involve choosing the audio format WAV AIFF CAF resolution 16 bit 24 bit 32 bit integer 32 bit float 64 bit float sample rate 44 1 kHz 48 kHz 88 2 kHz 96 kHz 176 4 kHz 192 kHz whether dithering is on or off and whether or not to link specific audio files to the audio processor chain such that when different files are loaded the chain of processors gets switched With the exception of the file processing chain linking option these settings apply to the target master file not the files you are loading which can be in any supported input format T RackS deals with the details of handling multiple input file formats so you don t need to worry about it Originally published on CakewalkNet com March 6 2008 Page 15 Playing Around Over the course of the roughly 7 weeks I had T RackS 3 Deluxe while working on this review I used it in a number of contexts including mastering and processing individual tracks For the most part things went well and I have really enjoyed the T RackS metering and processors It s always risky to try to deduce from2. 11 was really it for visual feedback on the audio results Note that there was also an EQ curve display but that was based on EQ settings not on the frequency spectrum of the actual audio being processed T RackS 3 starts by enhancing the output level peak meters then delivers a host of new meters to let you view what you are hearing from several different angles Let s take a look The peak meters which provide separate meters for the left and right channels include both instantaneous audio peak monitoring and temporary peak hold metering New to T RackS 3 are aver indicators for each channel to show when the output level has exceeded 0 dBFS Another new feature is the ability to configure the peak meters display to show any of three different audio scales The default scale which will generally be most useful for normal mastering purposes shows 60 dB to 0 dB with a zoom such that the upper half of the meters displays the 8 dB to 0 dB range thus making it easier to keep an eye on available headroom Other options include 90 dB to 0 dB with a zoom from 30 dB upward for monitoring the full range of the signal and 50 dB to 5 dB with a zoom from 10 dB up for looking into what is going on when overs occur Just below the peak meters are perceived loudness and RMS root mean square or average audio power meters Both of these combine left and right channels on a single meter RMS meters are fairly common for
3. My old solution was the clear winner due to better transparency especially in areas relating to the stereo field and front to back soundstage perception While it is always possible that learning curve considerations came into play with T RackS Ihave also seen similar results in the past when comparing results using a 32 bit data path or a 64 bit overall data path but constrained by a few strategically placed 32 bit plug ins to results with a full 64 bit data path up until the final downsampling and bit rate conversion Not all current DAWs support 64 bit data paths so this won t be a concern for some DAW users However SONAR has supported these for awhile now so it is at least a consideration for those SONAR users using 64 bit data paths which I d guess would be a majority of users of recent versions of SONAR When using T RackS 3 as a plug in at the track level in 44 1 kHz projects running with SONAR s 64 bit audio engine I occasionally encountered some issues with softsynths not playing notes that they were supposed to play Sometimes this was during playback only and not when rendering Other times it was when rendering only at certain ASIO latencies and changing the latency could affect whether there were problems in the render or not Sometimes the workaround was to set the latency higher and sometimes it was to set the latency lower In other words the behavior appeared to be unpredictable Note that the issue was the presence of th
4. a relatively short period especially one interrupted by the holiday season and a variety of other unrelated projects how one s long term use of a product will evolve once it gets past the learning curve and honeymoon phases However I do feel it s safe to say that I am likely to use T Rack 3 Deluxe processors in a number of individual track processing scenarios as I get more used to how those processors behave and how they compare to other processors I ve used to this point T also think it s likely I will at least consider using T RackS on mastering projects However whether it will win out for any given mastering project will depend on the project and there is at least one significant limitation which I get to shortly that I feel may hurt T RackS odds of being chosen in more critical cases The net is my overall experience with T RackS has been quite positive However I would be remiss if I did not mention a number of issues Iran into in the course of my use of both the standalone and plug in versions of the product The nature of some of these is such that it is hard to tell where the line between T RackS itself and the interaction between a plug in a plug in s system demands and the plug in host comes into play In other cases there seem to be some clear if difficult to pin down bugs in T RackS The first consideration I came across which I fel impacts T RackS suitability as a mastering plug in within SONAR and possibly
5. some but not all other DAWs is that the plug in version only has 32 bit data paths between it and the plug in host SONAR s audio engine has the capability of running at 64 bit floating point and many plug ins have now been updated to take advantage of that at both the track and mastering plug in levels It seems a shame to have all the extra resolution saved up through the entre mix cycle then immediately lop off 32 bits of resolution when going into a mastering plug in incidentally before it gets upsampled for T RackS internal processing This consideration also affects the decision as to whether to use T RackS as a component in an audio signal chain that includes other processors that have 64 bit data paths It is not however a big issue if T RackS is the first processor in line after an audio track that is starting at 16 bits or 24 bits of resolution Rather it is only a concern if the T ack plug in is coming after additional higher resolution processing has occurred which would almost always be the case at the end of chain mastering spot in a SONAR projects signal chain Tn my first real mastering project after getting T RackS I held a shootout between T RackS 3 Deluxe and my typical mastering chain a combination of PSP MasterPack plug ins and SONAR s Linear Phase Multiband Compressor all of which have 64 bit data paths throughout The mastering process was being carried out at 64 bit 96 KHz for a CD quality 16 bit 44 1 KHz result
6. the output level will suffice This makes for a nice tradeoff between simplicity and flexibility Brickwall Limiter T Rack 3 Deluxe introduces a new intelligent multi algorithm Brickwall Limiter This module is intended as the last module in T RackS chain and can be used for increasing the apparent loudness of the signal while ensuring the end result does not go beyond 0 BFS Starting at the left of the module s interface we see a control for linked stereo operation or for separately setting controls for the left and right channels When using separate controls the relevant knobs will be used to adjust Whichever channel is currently selected Most of the remaining controls will look familiar to those readers who are familiar with loudness maximizers There are gain reduction and output level LEDs an Input level knob with a range of 15 dB an Attack Time knob with a range of 0 05 ms to 10 ms a Release Time knob with a range of 0 1 ms to 1 second and an Output Ceiling knob with a range from 15 dB to 0 dB All of these knobs are subject to separate left right control if that is engaged The remaining control which is not subject to separate left right control is the Style control which sits at the top center of the module s interface This control selects the module s limiting algorithm from choices including Clean four Advanced styles 3 Saturation styles and Clipping Clean is the most transparent algorithm while Cli
7. with extreme settings just like the original Pultec model is reputed to do It seems to me to be one of those processors that has the potential to make just about anything passed through it sound better That may be especially true when the source material has originated in the digital realm Classic T RackS Equalizer The classic T RackS Equalizer is not new though it has been enhanced for T RackS 3 It is an analog modeled six band parametric equalizer While it was designed for the mastering environment it also works nicely at the track level and IK provides a number of presets geared toward its use on individual tracks Starting at the left of the module s interface you will find the by now familiar L R and M S mode and channel selection controls While these are familiar based on their having been covered above for the Linear Phase EQ and the Vintage Equalizer EQP 1A they are new to the T RackS Equalizer Moving to the right the top portion of the screen is dedicated to providing a graphic view of the EQ curve in use by the module While the graphic view is not new the ability to manipulate gain and frequency settings directly from the graph is new in T RackS 3 Below the graph are the standard knob based controls for the six filters included in this equalizer All filter bands can be enabled and disabled via a toggle button just under the main knob control for each band The outermost bands provide high pass and low pass filters whic
8. If you don t need all three bands you can effectively configure the module to have a lesser number of bands by setting the low mid crossover to 30 Hz and or the mid high crossover to 20 4 kHz To the right of the band configuration controls are the Release Time 80 ms to 1 5 seconds Overload 45 3 dB and Input Drive 9 dB to 16 dB controls The Input Drive control drives more signal through the input to the module Because there is a fixed threshold at which limiting is engaged it also controls the relative number of peaks that will be limited The Overload knob controls the way peaks are limited At lower levels there will be more frequent pure gain reduction whereas at higher levels there will be more frequent clipping To put it another way it is in essence a knee control with a softer knee at lower values and a harder knee at higher values The Multiband Limiter is rounded out by an analog style VU meter that displays average gain reduction across the three bands and an output level knob with a range of 18 dB Now that its bands are configurable the classic T RackS Multiband Limiter lends itself to a variety of special applications like de essing in addition to just helping you make things louder by separately processing three bands of the frequency spectrum For those who just want the older function simply resetting the unit to default values then adjusting the Release Time Overload and Input Drive knobs and possibly also
9. Review IK Multimedia T RackS 3 Deluxe by Rick Paul 6th March 2009 Mastering is one of those black arts generally thought of as best being left to professionals The wizards behind that art tend to bring years of experience and golden ears along with specially treated rooms high end monitoring systems and equipment beyond the reach of most of us mere mortals to the table Furthermore there is the benefit of bringing in a second often more experienced set of ears to offer a fresh perspective on recordings we may have been slaving away at for days weeks or even longer However not everyone can afford professional mastering and even those who may not be able to afford it for every project This is where mastering for the rest of us products come into play IK Multimedia was one of the pioneers in bringing user friendly software based mastering tools into the home and project studio arenas Their original T RackS mastering tool which was introduced back in 1999 provided a standalone rack of audio processors geared toward making mastering accessible enough for beginners while offering a fair degree of flexibility for more advanced users on a budget Almost a decade later T RackS has proven to be a popular product which is now entering its third generation with the introduction of T RackS 3 Deluxe which provides both standalone processing and operation as a plug in for use in most popular DAW hosts Let s take a look at this l
10. ackS easily accessible to new users On the minus side this interface provided limited flexibility with the key options being whether a module was engaged or not and whether the compressor was routed before or after the equalizer While T RackS 3 maintains elements of a hardware rack look what you see is decidedly not what you get There is a lot more behind the scenes including up to eleven additional rack modules only one is visible at a time more flexible and sophisticated module routing possibilities automation capabilities under DAW control and additional capabilities for configuring what is visible Where earlier versions of T RackS had one multi segment LED style stereo meter plus analog style VU meters for some of its modules T RackS 3 augments any module specific meters with a rich assortment of helpful meters that greatly aid the user in providing visual insights into what the ears are hearing While these new capabilities greatly expand T RackS power and flexibility T RackS 3 does come with a somewhat steeper learning curve and requires a bit of extra effort to maneuver its interface That is a small price to pay for the new functionality and a necessity when the needs of this new functionality are traded off against screen real estate considerations Let s take a quick look at how to get around T RackS new interface Looking at the plug in version of T RackS 3 there are four main interface areas A
11. an remove the assignment If you assigned it to the wrong parameter you can also move assignments up or down within the automatable parameter list Once you ve made all your assignments you simply say OK to the automation assignment screen and you re in business Originally published on CakewalkNet com March 6 2008 Poge 13 It probably goes without saying that this scheme has pros and cons The main benefit is that it keeps automation manageable whereas a huge number of automatable parameters can overwhelm a DAW on the performance front and or overwhelm the DAW user in trying to find the right parameters to automate Whether sixteen automatable parameters is enough for any given situation could come down either way but I suspect it is likely to suffice in most practical circumstances There are three key areas though where this scheme could prove unwieldy Fist there is the necessity of setting up the automation links between real parameters and automatable parameters visible to the DAW While itis simple and straightforward it doesn t come for free and does take awhile to set up each time you want to change something Second the assignments are slot and module dependent Thus for example to go back to the case of the Linear Phase EQ gain parameter automation you would not be able to use the same automation setup to automate that EQ in slot 1A if you d placed the EQ in slot 1B or 2A or any other slot Nor would that setup work for
12. and attenuation filters have different spans While in theory one might want to boost or cut not both in practice doing both has a unique effect due to the different EQ curves It can reduce muddiness by creating a bit of a scoop in the low mid range thus Tending to the musicality of this EQ Moving to the right the next two controls on the lower level and the remaining three controls on the upper level of the interface are for the high end filters Where the low end filters are both shelving filters the high end filters include a bell shaped boost filter and a shelving attenuation filter A Bandwidth knob narrows or widens the span of frequencies covered by the bell shaped high frequency boost filter The boost and attenuation knobs work similarly to the corresponding knobs for the low end filters A high frequency selector switch allows choosing between five possible center frequencies 3 4 5 8 10 12 16 kHz for the high end boost filter In the top right hand comer an Attenuator Select switch similarly provides a choice of three corner frequencies 5 10 20 kHz for the high end attenuator shelving filter An output level knob with a range of 15 dB sits in the lower right hand corner of the EQP 1A s interface Having never had access to a real Pultec EQP 1A I can t vouch for the accuracy of IK s modeling of that equalizer here What I can say is that the T RackS Vintage Equalizer EQP 1A does indeed provide highly musical results even
13. atest incarnation Background IK Multimedia s T Rack 3 Deluxe is an analog modeled mastering solution provided in both standalone and plug in form Either way it provides an all in one processing chain as opposed to individual plug in modules intended for routing at the DAW level T RackS also provides significant routing flexibility within itself for mixing and matching its modules in serial and or parallel signal chains Since you can include as many or as few modules as you like within an instance of T RackS and use multiple instances of the T RackS plug in in your DAW you can also mix and match T RackS modules with other processing modules at the DAW level IK bills T RackS 3 as a modular high end mastering mixing suite of Originally published on CakewalkNet com March 6 2008 Paget dynamics and EQ processors including 9 processors comprised of 3 new analog and vintage emulations including models based on the Fairchild 610 and the Pultec EQP 1A 2 new digital processors as well the 4 classic award winning T RackS processors New configurable mastering mixing chain run up to 12 parallel series processors New complete built in metering section with Peak Perceived Loudness Phase and RMS meters plus a Spectrum analyzer with Peak RMS and Averaging indicators New standalone and plug in versions available in the same package for use in all the most popular native DAWs New high fidelity oversampling w
14. cach with multiple automatable controls T RackS could potentially have an overwhelming number of automatable parameters Add to that the notion that neither T RackS nor your DAW software can predict which T RackS module will be in use at any given time no less which parameters a given user will want to automate and this creates a dilemma How can T RackS provide for automatable parameters without making for a highly messy situation T RackS 3 addresses this dilemma through a decided compromise but a compromise that seems reasonable given the considerations mentioned and the practical nature of what users are likely to want to do It presents a list of up to sixteen automation parameters to your DAW while letting you tie each of those sixteen parameters to a specified control of a specified module and slot in your T RackS configuration For example perhaps you might want to tie the first six automatable parameters to the gain controls for the six bands of the Linear Phase EQ in Slot 1A of your configuration so you can make EQ level adjustments over the course of the song When setting up the parameters you would first select Slot 1A then the Linear Phase EQ and then the specific band of Gain you want to tie to a given automatable parameter After selecting the band of gain and the Parameter it will be assigned to you simply click the Add button in the automation assignment screen to make the assignment If you made a mistake you c
15. ce analog flavored EQ for use at the track level In fact it has frequently found its way onto my lead vocal tracks where I find it to enhance the frequency oriented processing in much the same way a mild diffusion filter can enhance a portrait ie by ever so slightly softening the edges of the part Opto Compressor T RackS 3 s new Opto Compressor is based on analog modeling of high end optical compressors Optical compressors have special characteristics due to the inherent physics of the way their components work These include source dependent time lags in the attack and release times that yield musically pleasing results While the Opto Compressor imparts an analog flavor it is also the least colored compressor available in the T RackS 3 Deluxe suite of processors Starting on the left hand side of the module s interface you will find the familiar mode switch for linked or unlinked LR or M S operation To the right of that along the top of the interface are four knobs An input level knob provides 24 dB of gain The compression ratio knob allows setting the ratio from 1 0 or no compression to 30 1 which is for most practical purposes limiting An attack knob ranging from 0 to 50 ms follows then a release knob ranging from 30 ms to 5 seconds Below the attack and release knobs is a large Compression knob which sets the amount of compression applied to the signal from no compression to full compression Next up to th
16. dules directly as separate plug ins rather than having to insert the full T Racks plug in then insert a single processing module in that For example there are certainly times where I would only want to use the Vintage Compressor Model 670 or Vintage Equalizer EQP LA in a chain with processors from other vendors Or perhaps Td like to use both of those modules with another non IK module in between them In such cases having to have the whole T RackS module including all those meters is cumbersome not to mention likely a fair amount of extra CPU overhead Additionally looking quickly at a plug in chain that has an entry Iabeled T RackS 3 when all that is included in it is the Opto Compressor for example is not as helpful as looking at that same plug in chain and seeing Opto Compressor or T RackS Opto Compressor This is especially true if there are multiple instances of T RackS within that chain e g separated by a third party plug in I admit to being spoiled by the old T RackS EQ which was indeed available as a separate processor and became a frequently used plug in in my track level signal chains Besides wanting the audio modules available as separate plug ins Td also love to have the meter section available as a separate plug in for those cases where it might be nice to use those while not using the rest of T RackS It isn t just the extra CPU overhead I d be concerned about in that case but also the extra screen real estate Thi
17. e T RackS plug in in the project not necessarily in the track that was being affected I might also note that T RackS has a lower latency setting intended for issues like this where quality of the result is reduced in exchange for real time performance However setting that option did not help in at least some of the cases I have not yet gotten to the bottom of these issues to know if there is a bug somewhere if there are tuning parameters that can be set for more consistent results or what the ultimate cause and resolution may be I might add that it isn t purely a CPU consumption issue as CPU usage Originally published on CakewalkNet com March 6 2008 Page 16 could be low with very little going on in the face of these issues and the difference in whether things worked properly or not was if T RackS was inserted and active This is not to say there is necessarily a bug in T RackS e g it could be a problem in SONAR 8 0 2 s plug in latency compensation or some other performance and or rendering oriented aspect of SONAR However it decidedly did present a practical problem in actual use of T RackS within SONAR for some of my projects Ultimately when I found a combination that worked I just had to freeze the relevant tracks to capture the results to audio while the going was good Speaking of using T RackS as a plug in at the track level I would really have liked to have had the possibility of using T RackS individual processing mo
18. e right are analog style VU meters These are triple duty meters that can measure gain reduction the default or the input levels to or output levels from the module The output level knob which is located in the lower right hand comer of the module provides 424 dB of gain T have to say that this is a really nice compressor While it has an analog flavor it is also very transparent when set appropriately At first I found it a bit disconcerting that there was no traditional threshold setting since pretty much all the compressors I regularly use have those However as I used it more I started feeling this design difference became a benefit forcing me to use my ears rather than my eyes and some calculations Also when I revisited a few of the compressors I ve used more regularly which do have threshold controls I found myself having to do more work to figure out the settings to use as the T RackS Opto Compressor ultimately feels easier to use for getting desirable results Vintage Compressor Model 670 T RackS 3 Deluxe s Vintage Compressor Model 670 models the venerable Fairchild 670 Limiting Amplifier which could function as either a compressor or limiter depending on settings That unit is sometimes called the holy grail of compressors due to its rarity its expense on the vintage equipment market and the difficulty in maintaining it Thankfully IK s recreation of this unit in T Rack 3 Deluxe can be found at many music sto
19. ed to do so for that matter Meanwhile the problem has been a serious hindrance to my use of the standalone version of T RackS 3 because my attempts at file rendering tend to result in silent WAV files on the order of a quarter of the time IK responds that there are thousands of T RackS 3 standalone users that are not getting silence when they process Originally published on CakewalkNet com March 6 2008 Page 17 Closing Notes The net is I have mixed feelings on T RackS 3 Deluxe On the one hand I absolutely love the processors and metering capabilities and would like to be able to use those more extensively in my work both for mastering and for track level processing I also anticipate I will use the product more over time both as product bugs get fixed and as I come to grips with how to work around the bugs and or other issues that don t get sorted out On the other hand T have ended up needing to work around a number of issues in several distinct areas I m not talking about obscure things that only come into play a small percentage of the time but rather things I ve encountered quite frequently over the course of using the product The exposure I ve had to IK s support thus far also doesn t give me the warm fuzzies that they even recognize that there is an actual problem in the area I d raised to them I have not raised the other issues to IK as yet because I can t document them to the point of having any recipe or even knowin
20. eft hand comer of the audio window help in zeroing in on trim and fade points There is also a looping capability with draggable start and stop points to make it easy to repeatedly loop over any desired section of audio while trying to determine trim and fade points or adjusting processing settings While the standalone version of T RackS 3 does not provide continuous automation it does provide a snapshot facility via the audio window You can take up to nine snapshots of various states of the T RackS module configurations and settings then switch among them instantaneously on playback These instantaneous switches can g0 beyond just automatic parameters For example the actual modules in the chain could be different in different snapshots The time for starting each snapshot can then be adjusted by dragging the marker associated with the snapshot around the audio window Snapshots can also be copied if for example you would like to apply the same snapshot to every chorus in a song while using other snapshots for the remaining song sections In this case you would copy the snapshot you are using for the chorus and just drag the new copy to the second chorus then repeat the process again if there is a third chorus Of course you do need to beware of the potential for making extreme changes in audio processing if two consecutive snapshots have very different settings At the bottom left of the audio window is the transport with stop and
21. er time The new SCC Sonic Character Cloning technology analyzes the actual behavior of analog processors then models that behavior erratic elements and all mathematically with the goal of modeling what the equipment actually does do versus what an analysis of the schematic might suggest it should do Let take a look at the processors available in T RackS 3 Deluxe Since CakewalkNet has not reviewed earlier versions of T RackS we will include the original classic T RackS processors as well as the five new processors introduced with T RackS 3 Deluxe Originally published on CakewalkNet com March 6 2008 Pages Linear Phase EQ The new T RackS Linear Phase Equalizer is a six band equalizer that offers optional linear phase coherency engaged via a button in the lower right hand comer of the module s interface Linear phase coherency means that the timing of the various bands of the frequency spectrum are kept in phase with each other despite the frequency spectrum processing that is going on This results in a more transparent sound than a traditional equalizer which can slightly smear timing aspects between bands Even when not operating in linear phase mode the T RackS Linear Phase EQ will impart a minimal level of phase distortion to its output signal Each of the six bands of EQ which can individually be enabled or disabled can be configured for low or high pass low or high shelf or band pass band cut operat
22. ess the mechanism gets the job done and with a minimal amount of screen real estate which is helpful since T RackS 3 already consumes a fair amount of vertical space Over in the top right hand corner there is a Show Chain button which makes a graphic display of the processor chain and its contents fill the space normally occupied by the currently selected processing module sce below in the Chain Chain Chain section Just below that there is a Compare button to engage T RackS Compare function which allows quickly A B ing the processed version of the signal against the unprocessed version of the signal Below the Compare button itself are two related controls An On Off bution toggles back and forth between comparing the processed signal On and the unprocessed signal Off when Compare mode is engaged To the right of that is a volume control which is used to set the volume of the processed or unprocessed signal depending on whether the On Off button isin the On or Off state respectively This allows setting similar volume levels for each signal so the level difference between the two signals does not unduly cloud your judgment as to which version of the signal sounds better Once you ve set the respective volumes you can just toggle the On Off button back and forth to compare the processed and unprocessed signals Originally published on CakewalkNet com March 6 2008 Pages BRT 2012 hoe eft core of the pl
23. example SONAR s meters can be configured to display RMS instead of or in addition to peaks The perceived loudness meters however while not unique to T RackS 3 are fairly uncommon and highly useful Where the RMS uses a flat frequency response in its measurements the perceived loudness meter combines averaging and frequency weighting to display the sense of loudness a listener would get from the audio signal IK adds to this by providing 27 loudness suggestions based on common musical genres For any given loudness suggestion a green area and a red area will appear underneath the perceived loudness meter The idea is that the green area represents where most loud areas within that genre should be peaking while the red area represents where the most extreme loud passages should peak for that genre I have to say I found some of the loudness suggestions curious For example the loudness suggestion for hip hop rap was considerably lower than that for pop rock The one for hip hop rap felt fairly reasonable to me while the one for pop rack resulted in your basic square wave masters that are a common result of the so called loudness wars that plague modern recordings That made me wonder what recordings were used for determining these suggestions and whether those recordings were representative of good taste in mastering or just the current state of the industry or perhaps even just some arbitrary pick from a particular set of recordings Of co
24. figured the automation for that project unless that is you change your mind later about what modules will be in which slots Standalone Extras SONAR users and users of other DAWs have the option of using T RackS 3 as a plug in or as a standalone application Unlike in the case with standalone software instruments where DAW users will almost always prefer to use the plug in version there are a number of situations where using the standalone version of T RackS may be preferable to using the plug in Since mastering is for a number of reasons generally best considered as a process separate from mixing if T RackS modules will comprise your total mastering chain there is no inherent advantage in using T RackS as a plug in over using it as a standalone processor Of course if you are combining the mixing and mastering stages it is likely to be easiest to simply put T RackS at the end of your SONAR signal chain and be done with it Since T RackS can also be used for processing individual tracks and submix buses there are also other cases where it will make the most sense to use T RackS as a plug in However once you have individual audio mix files for mastering the verdict on whether to start one or more new SONAR projects for mastering or whether to simply use T RackS in its standalone form will come down to your needs and preferences A particular scenario where I d expect using the standalone version might he the course of least resistance
25. g if they are truly IK issues Cakewalk issues or in between the two I also do think having the T RackS plug in support full 64 bit data paths is important for SONAR users and is especially limiting in the area of using T RackS for mastering within SONAR believe the positive aspects of T RackS 3 Deluxe will ultimately outbalance the negatives but there are a boatload of mastering plug ins out there in the market at all price points When significant workflow problems arise it is all too easy to find something that also sounds good but doesn t have the same hassle factor I sincerely hope IK will get those sorts of issues worked out so users can simply enjoy what is otherwise an excellent set of processors Rick Paul is a singer songwriter living in Southern California You can contact him at http www RickPaul info Originally published on CakewalkNet com March 6 2008 Page 18
26. h have neither Q nor gain controls Thus the top and only knob control for those bands is simply a cutoff frequency control The top knobs for all other filter bands are gain knobs supplying 15 dB of gain The next outermost bands are low and high end shelving filters and provide a corer frequency control in addition to their gain cut knobs The two innermost bands are standard peaking filters which provide center frequency and Q controls in addition to their gain knobs Unlike the Linear Phase EQ where any filter band can be set to any frequency the classic T RackS Equalizer s bands have frequency ranges that are limited to subsets of the overall range according to their left to right corresponding to Originally published on CakewalkNet com March 6 2008 Page ow to high frequency order in the module s interface While this may not provide quite as much flexibility this in conjunction with the fixed functions of the various bands does tend to make keeping track of which band is doing what more intuitive Over on the far right hand side of the module is an output level control that provides 18 dB of gain The classic T RackS Equalizer sits in territory somewhere between the Linear Phase EQ and the Vintage Equalizer EQP 1A Itis not as transparent as the Linear Phase EQ but has much more detailed control over the EQ curve than docs the EQP 1A Having used the earlier version of the T RackS EQ plug in I have found it to be a ni
27. hter values for the momentary readings ala the phase scopes in iZotope Ozone 3 or PSP StereoAnalyser However the different speeds do at least provide some options and using a slow speed is a reasonable compromise for the lack of this capability Originally published on CakewalkNet com March 6 2008 Page 12 The phase correlation meter shows the phase correlation between the left and right channels of the stereo signal on a scale from 1 to 1 When signals are in phase the meter should be reading a value between O and 1 with a fully mono signal showing 1 and a fully out of phase signal showing 1 This reading can give an indication of how successfully a signal can be collapsed to mono with higher numbers being more mono compatible and negative numbers likely to yields significantly weaker mono signals because their being out of phase results in one channel s subtracting level from the other when collapsed to mono To the right of the phase meters is a 1 6 octave FFT spectrum analyzer The spectrum analyzer is also highly configurable to suit user preferences and analysis of specific issues The meter displays multiple bar graphs by default but it can also be configured to be a segmented line graph The audio level range is configurable to either 90 dB to 0 dB or 60 dB to 0 dB The bars can display peak RMS or average values If average is selected there will be a delay in getting to an initial reading after which the display sh
28. ion and is fully sweepable over the range from 10 Hz to 20 kHz The Gain Res knob for each band provides 15 dB of gain for all filter styles except low pass and high pass where it operates as a resonance control The Q knob provides settings from 0 2 to 20 for the peaking i e band pass band cut filters and serves as a slope control with resonance with a range of 0 2 to 3 in shelf mode It is disabled in low pass and high pass modes Besides using the knob controls to adjust frequency and gain for the filter bands there is also a graphic display that allows direct manipulation of nodes on the graph The graph does not provide Q manipulation however Over on the left hand side of the module s interface are controls to set the mode of operation of the EQ It operates in Left Right L R mode by default with left and right channels linked such that changes made to the EQ curve affect both stereo channels However it also provides separate control over left and right channels by pressing an or R button respectively then tweaking a green or red curve Mid Side M S operation is also supported When this mode is engaged the controls that were previously labeled L and R are relabeled M and S respectively Pressing these then tweaking the EQ curve allows setting separate equalization curves for the center and side signals The Linear Phase EQ also provides a peak meter that displays the level of the module s o
29. ion process is a simple matter utilizing the standard conventions of the applicable system such as a Setup program under Windows Software protection uses an on line authorization system based on the product serial number a digital ID generated by the software for your hardware and an authorization code supplied as part of the on line authorization process There are also offline possibilities available via fax or snail mail and the product will run for 10 days after installation without authorization to provide some grace period in the event of authorization delays Suggested list price for T RackS 3 Deluxe is 499 99 379 99 There is also a crossgrade to T RackS 3 Deluxe from most other IK Multimedia products for a list price of 299 99 229 99 For those users looking for a lower budget option T RackS 3 Standard which includes only the original four T RackS processors plus updated metering lists for 199 99 149 99 It probably goes without saying that street prices can be significantly lower and IK also has periodic promotions such as two for one deals that can make the ultimate product price paid even lower for customers who want multiple IK products For example at the time of this writing the lowest street price I found for the full shebang which was of the too low to print variety that required adding the product to a shopping cart to see it was 310 63 That itself would represent a pretty good savings but there wa
30. ith crystal clear transparency for high quality audio processing throughout the entire signal path New SCC technology coupled with IKs unique DSM technology provides the most realistic software emulation of vintage gear to date Extremely easy to use with style based presets full chain visualization one click single module or chain bypass compare function multiple audio processing in standalone mode and much more Well be looking much more closely at the processors metering and more below System requirements and plug in formats for the various platforms supported are as follows Power PC based Macintosh Minimal 866 MHz G4 processor 512 MB of RAM Mac OS X 10 4 or later Suggested dual 1 25 GHz G4 or G5 processor 1 GB of RAM Mac OS X 10 4 or later Supported Plug in formats AU VST RTAS Intel based Macintosh Minimal 1 5 GHz Intel Core Solo processor 512 MB of RAM Mac OS X 10 4 4 or later Suggested 1 66 GHz Intel Core Duo processor 1 GB of RAM Mac OS X 10 4 4 or later Supported Plug in formats AU VST RTAS Windows Minimal Pentium 1GHz Athlon XP 1 33 GHz 512 MB of RAM Windows XP Vista or later Suggested Pentium 2 4 GHz Athlon XP 2 4 GHz 1 GB of RAM Windows XP Vista or later Supported Plug in formats VST RTAS In addition to the software the product includes an 86 page user manual and a 12 page installation and authorization manual The installat
31. ld control so the amount of compression is determined by the strength of the input signal Above and slightly to the right of the Input Drive knob is the Stereo Enhancement knob which provides 5 dB of stereo width enhancement Negative values lower the apparent width while positive values increase the width Further to the right still are an analog style VU meter that measures gain reduction and an output level knob with a 18 dB range Originally published on CakewalkNet com March 6 2008 Pages Like the Vintage Compressor Model 670 the classic T RackS Compressor provides color in addition to doing its dynamics processing job That color is different than that of the Model 670 While I tend to prefer the Model 670 for color and the Opto Compressor for more transparent uses it s always nice to have additional flavors Classic T RackS Multiband Limiter The classic T RackS Multiband Limiter isa three band peak limiter with a decidedly analog flavor It sports eight new knobs compared sy to the version of this module in T RackS 2 0 All of these new controls serve one key purpose though they make the individual bands of this module configurable Each band has a 12 dB threshold control and a 12 dB level control The other two controls set the crossover frequencies between the three bands with a range of 30 Hz to 1 9 kHz for the divider between the low and mid bands and a range of 1 kHz to 20 4 kHz between the mid and high bands
32. minated then click on the current preset name and choose a preset from the pop up menu of IK provided and user created presets To pick a preset for the current hardware module make sure the Module button is illuminated then pick a preset for the module you want Note that doing this will change the module loaded in the current slot if you choose a preset for a module other than the one that is currently loaded in that slot You can also scroll between Global or Module presets using arrow controls save your changes to a preset including saving it with a different name and delete presets A separate Preset button also allows loading a preset from a location other than the default location used by T RackS e g if you are sharing presets with another T RackS user While advanced users may prefer to create their processing chains and device settings based on the needs of a given project new users will likely appreciate the meaningfully named starting points provided by IK in the presets Even experienced users will likely appreciate the ability to create and recall their own presets for loading commonly used processing chains and for use in any batch projects with similar processing requirements The middle top section of the T RackS 3 interface is occupied by a block of controls that allow manipulating and accessing the chain of processors and which partially depict its contents There are eight squarish blocks of controls The fir
33. n acoustic instruments I tried it on a bluegrass style piece and it did indeed work magic It can also be quite useful on individual instruments or vocals I tried one of the vocal presets on the lead vocal for a quick piano vocal work demo and it was just what the doctor ordered Classic T RackS Compressor The classic T RackS Compressor emulates classic high end tube compressors used in mastering While it does not provide mid side Sir processing like the other modules we ve covered thus far it does bring a few extra tricks along with its classic compressor functions S Starting off in the upper left hand comer of the module is a Sidechain HPF high pass filter control As the word sidechain implies this filter doesn t act directly on the Processed sound but rather filters what is fed to the compressor s detection circuitry Its range is 32 Hz to 218 Hz and the idea is to control the amount of influence lows and low mids have on the compressor s action For example this can help prevent or reduce the pumping effect that occurs when a bass part is exerting too much influence on the compressor s action This is a new feature in T RackS 3 Next up to the right are standard attack time 12 ms to 82 ms and release time 29 ms to 1 4 seconds controls with ratio control 1 5 1 to 4 68 1 underneath the attack control A large Input Drive knob 15 dB sits to the right of the ratio control The T RackS compressor doesn t have a thresho
34. nd can thus be one of the aspects of a particular model that contributes to subjective preferences for one model or another Classic T RackS Soft Clipper The classic T RackS Soft Clipper provides another end of chain loudness maximizing option geared primarily toward analog style saturation It enhances the clipper function of T RackS 2 0 by providing separate lefUright controls Le via the same linked operation or left right select buttons as used in other modules such as the Brickwall Limiter instead of a left right balance control and by providing gain reduction and output level meters The output level meters are particularly interesting as they start from the outside and rise Le in level toward the common center of the vertically oriented meter Beyond the meters and linked leftright buttons there are three knob controls A Gain knob provides 15 dB of input gain to drive the saturation and clipping A Slope control provides continuously variable control of the knee of the clipper from soft saturation starting at 12 dB to hard clipping at 0 dB An Output level knob provides control over the output level from 60 dB to 6 dB There is also a Saturation indicator light which lights when the signal is saturating and left and right overload lights to show when the signal has exceeded 0 dBFS meaning itis time to turn the Output level knob down Its interesting that the Brickwall Limiter and the Soft Clipper have similar functio
35. ns both providing saturation and clipping but yet have some decidedly different design choices While the Brickwall Limiter gives a choice of multiple algorithms but does not provide continuous control of those algorithms the Soft Clipper picks one algorithm but provides continuous control over it The output level metering is also quite different and the LED style indicators for saturation and channel level clipping on the Soft Clipper also provide a bit of extra information find it somewhat curious that IK didn t simply incorporate the continuous saturation slope control and extra indicators in the Brickwall Limiter then choose whether they preferred the more standard output level meter or the outside to center style meter and go with that Of course the Soft Clipper is the only clipper choice in the Standard version of T RackS 3 so there is the additional model to keep separate for packaging purposes Nevertheless it seems like the extra functionality in the Sofi Clipper could also have been useful in the context of the Brickwall Limiter Metering Without minimizing all the excellent new processing modules and enhancements to existing modules I think it is fair to say the most immediately apparent area of enhancement in T RackS 3 is its metering T RackS 2 provided multi segment LED style output level meters and analog style VU meters in each of the dynamics modules but that Originally published on CakewalkNet com March 6 2008 Poge
36. or limiter Fully counter clockwise is the softest knee and fully clockwise is the hardest knee To the right of the AGC control and DC Threshold controls are the Lefi Lat and Right Vert Time Constant switches These switches which are tied together in Link mode set the attack and release time combinations of the compressor The first four positions which go from fastest to slowest use fixed release times while positions 5 and six use two program dependent release times Next up to the right are the Input Gain knobs for Left Lat and Right Vert These knobs are not linked in Link mode Just to the right of the Input Gain knobs are the Treshold knobs which are linked in Link mode Further to the right are a pair of triple duty analog style VU meters with input output and gain reduction modes as on the Opto Compressor and an output level adjustment knob with a 15 dB range The Vintage Compressor Model 670 is one of those modules that impart some color just by being in the signal chain It can impart a little color or a lot of color depending on its settings What I particularly like about this compressor is the way it can glue a mix together while enhancing the detail that comes through from the individual elements That almost feels like a contradiction but maybe that is the magic I ve heard mentioned in many descriptions of the Fairchild 670 IK also provides a preset called 1dB 670 Magic I find this compressor to be especially nice o
37. ould stabilize to give a fairly steady reading of the signal s frequency spectrum curve A tilt value can be set to make the curve rise with frequency Readings can be taken from either the left plus right signals the default or from either individual channel Peak mode fall time for the bars and the resolution of the analyzer can also be configured and peak hold indicators can be enabled or disabled The analyzer can be turned off to save on CPU cycles The combination of meters provided by T RackS 3 is extremely useful for getting a visual sense of what is going on with your audio While one might argue that mastering should be done primarily by ear those of us with less than golden ears and or less than optimal acoustical environments often need the sanity check that meters provide to help augment what we are hearing and provide some clues to what we may not be hearing I also find the perceived loudness meter to be a very nice and fairly unusual touch to help get a handle on one of the more difficult areas of mastering multiple tracks for an album i e keeping the perceived loudness of tracks relatively consistent when the types of tracks vary significantly While there are plenty of other options out there for metering that is useful in mastering T RackS 3 goes a step beyond most solutions by putting all of the most useful visual indicators together Automation With up to twelve modules potentially in use at any given time
38. play buttons a time counter and the loop enable button To the right of those controls as of T RackS 3 0 1 there is an ARC button to enable integration with Ik s ARC Advanced Room Correction System If ARC is installed and enabled T RackS output will be processed by the ARC system to correct for room deficiencies for more accurate monitoring assuming of course the ARC system has been configured properly for your room and setup If the ARC system is not installed this button will simply bring you to the IK web page for information on ARC Once you have everything the way you want it itis time to render your files This is done via a Process button in the lower right hand comer of the screen This will bring up a dialog box to allow you to select the output format WAY AIFF or CAF whether to only process the currently selected file or all files in the list and some file name oriented information Inthe case of processing just the current file the file name information would be the location and name of the file itself Ifyou were processing all files then it would be the directory for the files and an extension for T RackS to append to the mix file s name to get the master file Note that options such as bit depth for the mix and whether dithering is on or off are not supplied here Rather they are specified in the properties of the T RackS project Speaking of which Besides the audio file handling controls we ve covered to this point
39. pping simply does hard clipping at 0 dBFS or whatever level is set on the Output Ceiling knob The three Saturation Originally published on CakewalkNet com March 6 2008 Page 10 styles use various saturation algorithms to gradually taper off the signal prior to the point at which it would clip The four Advanced styles use a blend of saturation and digital limiting Note that only Clean and the four Advanced styles will show any gain reduction on the Gain Reduction meter At various times in the past I ve been known to set up shootouts between different loudness maximizers to see which sounds best on a particular recording One of the cool things about the T RackS Brickwall Limiter is that its nine styles of brickwall limiting are similar in practice to being able to set up such a shootout between nine different maximizers by changing the value of a single control Of course if you ve got other loudness maximizer modules you may still find other flavors to try outside of this module but for those who don t it is nice having multiple favors within a single module One thing worth noting here is that while the standalone version of T RackS 3 includes optional dithering the plug in version does not This is no big deal if you like the dithering provided by your DAW For example SONAR Producer Edition s POW R 3 dithering is top flight stuff However dithering and noise shaping are frequently found in loudness maximizer modules a
40. res won t set you back anywhere near as much and has no transformers or tubes to go bad Let s take a look at IK s model Originally published on CakewalkNet com March 6 2008 Pages If you noted the key common point for all the modules we ve covered to this point one thing you ll notice quickly when looking at the controls for the Model 670 is it doesn t have the standard L R and M S mode controls we ve seen on other units It does do mid side processing but the controls not only look different but they are also labeled differently Where we ve thus far seen M S the Model 670 uses Lat Vert for Lateral Vertical with Lat quite unintuitively in my opinion but hey they re being true to the original hardware labels and people pay big bucks for that hardware being Mid and Vert being Side The mode switch labeled AGC Automatic Gain Control here is a three position toggle with Left Right Link and Lat Vert positions Where the modules we ve discussed thus far use a channel selection switch to allow other controls to do double duty the Model 670 has separate controls for left and right and or lateral and vertical When Link mode is engaged some of the controls will also be linked in their motion while others still offer independent operation Just below the mode selection switch are the DC Threshold switches for Left Lat and Right Vert DC threshold It turns out this is actually the control for the knee of the compress
41. s also a Buy 1 Get 1 Free sale going on at the time That promotion allowed choosing a second IK product the list of possibilities for purchasers of T RackS 3 Deluxe included SampleTank 2 5 XL AmpliTube 2 Classic Studio Reverb and many Originally published on CakewalkNet com March 6 2008 Page more for free download upon registering That deal will likely be over by the time this review is published but it s always worth checking IK Multimedia s web site for the latest promotions T tested T Rack 3 Deluxe on a custom built system with an Intel Care 2 Duo E6600 CPU with 4 GB of RAM and Windows XP SP3 fully patched to latest Windows Update levels The audio interface was the E MU 1820M running v2 0 DAS drivers and PatchMix software The plug in version was tested under Cakewalk s SONAR 8 0 2 Producer Edition Quick Tour Those familiar with earlier versions of T RackS will recall a user interface that looked very much like a rack of hardware mastering processors In fact the name T RackS would seem to be a play on words combining T Rex Gie Tyrannosaurus Rex which still appears in the T RackS logo and the notion of a rack of gear While there were a few minor departures from the hardware rack module interface the controls were by and large sitting there staring at you in one multi unit rack There were pros and cons to that approach On the plus side almost all functionality was instantly available and visible making T R
42. s is also true when wanting to use just individual processing modules where I might not want the meters Finally while attempting to use the standalone version of T RackS 3 Deluxe Iran into a recurring problem where processing my files resulted in master WAV files that were the right length but contained total silence or in one Case an initial burst of noise followed by total silence I reported this problem to IK s technical support including providing step by step details of what I did including noting times when the same steps yielded different results It is the kind of issue that seems to recur frequently but which is difficult if not impossible to replicate with one simple recipe that always fails in the same way In particular the issue seemed to center around making name changes in the relevant files For example after doing a Save As with the T RackS project e g to be able to return to past settings if the new one didn t work out I would run the Process command to render the audio file then change the name of the rendered file ie so as to not overwrite the results of an earlier render before letting it render Sometimes T d get the proper result and other times I d get the silent WAV file treatment When the render wasn t going to work properly it became evident right away because the graph indicating the status of the rendering operation would move very slowly compared to when it was going to work properly Unfor
43. st four blocks represent two four slot processor chains running in parallel paths labeled A IA 2A 3A 4A and B 1B 2B 3B 4B An abbreviated processor name for either the A chain or the B chain appears in the largest area within each block with which one is shown at any given point depending on whether a yellow light illuminates the A e g 1A 2A etc selector or the B e g 1B 2B etc selector e g as in the 1B 2B 3B and 4A slots in the above screen shot A litte red triangle in the lower left corner of the slot selector is used to show that a processor is present in any blocks that are not selected e g in the 1A and 2A blocks in the above screen shot The remaining flour blocks represent a single processor chain which occurs after the parallel four slot chain in the signal flow Any processors in those slots are always displayed in abbreviated form within those blocks At the bottom of each of the eight blocks is a pull down menu to select the processor that will be in the selected slot of the processor chain Clicking on the processor s abbreviated name will alternately bypass and reconnect the processor in that slot It takes a little while to get used to reading and using this interface This is especially true in the case of the parallel processor chains in the first four slots where one slot can represent two different processors and the processors visible at any given time may not actually be in the same chain Neverthel
44. t the top of the screen is a set of general controls including a mini representation of the virtual rack in use at any given time Well look at those Controls in more detail shortly Just below the general controls is the rack module area This view shows one module at a time as selected by the general controls Alternately it can depict a graphic representation of the entire signal processing chain We will go into much more depth on the processing modules and signal chain later in this review Below the module area are the meters which we will also cover in depth in a later section of the review Finally down at the bottom of the plug in s interface is another set of buttons providing access to various information and setup screens and access to snapshots of settings The standalone version of T RackS adds a number of file handling and transport functions below its interface elements that correspond to the plug in version We will also look at those in more depth later in the review For now let s take a closer look at the general controls at the top and bottom of the plug in interface Originally published on CakewalkNet com March 6 2008 Pages Up in the top left hand comer are a variety of controls for dealing with presets T RackS 3 ships with a rich set of presets for both the entire processing chain and the various individual processing modules To select a preset for the entire processing chain make sure the Global button is illu
45. tine looking vintage EQ On the far left hand side of the EQP 1A are the processing mode controls for L R or M S operation as described above for the Linear Phase EQ While the Linear Phase EQ has a visible EQ curve that keeps both of its potentially Originally published on CakewalkNet com March 6 2008 Pages independent curves visible at all times i e other than when in linked mode your only clue that left and right or mid and side may have different settings on the EQP 1A will be the status of the mode and channel selection buttons For example if one of the channel modes buttons i e L or R or M or S is pressed it is a clue that there may be different settings To check though you will need to press the opposite channel s button to see if the knobs move Moving toward the right the first three controls encountered are the boost control for the low end shelving filter a multi position switch to set the comer frequency for the bass shelving filters to one of four fixed values i e 20 40 60 100 Hz and an attenuation control for a low end shelving filter It might seem counter intuitive to have two shelving filters one to boost and one to attenuate at the same frequency after all wouldn t any boost be canceled out by any attenuation thus making it more sensible to have a single control that covers the desire range of cut or boost However the design of the Pultec EQ that is modeled here was such that the boost
46. tunately if my interactions with IK s technical support on this matter were representative I would have to consider their support to bbe a decided weakness First it took more than a day and a half for them to get back to me at all i e beyond the instant automated response to indicate the receipt of my support query When they did respond the response seemed to have ignored important details of my original problem report rather putting up a red herring related to one of those details that should have been answered by my initial report In particular the response keyed in on my mix file s having been a 64 bit 96 KH file rather than 16 bit 44 1 kHz like the intended master format It suggested I try to process the file at the same bitetc that you bounced it at and let me know This is after my original problem report had indicated that my first attempt at mastering the same mix file had succeeded and it was only after changing some processing settings and renaming the project and master file and render file that the problems started I eventually did recreate the problem using a 44 1 kHz mix too just to ensure that consideration Could be taken totally off the table even if it never should have been on the table in the first place The net is that after several correspondences elapsed over the period of a week I still don t know one way or another if IK has logged this problem as a bug or been able to recreate it on their end or even tri
47. ug in interfaco hero are series of utility buttons The Lock button on the left provides access to registration functions or registration information depending on whether your copy of T RackS 3 is already authorized The Info button provides typical Help About type information such as the software version number To the right of that is the Pref Preferences button which allows setting three important plug in level parameters In particular it allows choosing between lowest latency operation e g when needed for semi real time monitoring oversampling for higher quality processing but also higher latency or oversampling plus linear phase coherency for best processing quality but at the expense of even higher latency this option is required for use of the Linear Phase Equalizer It also allows choosing whether or not to provide D A Distortion detection which is only available in the two Oversampling modes and which prevents implied i e based on signal slopes overloads that would appear between samples and whether or not to use hard clipping to clip the output signal to OdB i e even if the processing chain prior to that point would result in a higher level signal Inthe lower right hand comer are a series of snapshot controls ES TTI When the Copy To button is pressed it makes a copy of the current settings of all the processors in the signal chain and their position in the signal chain There are four lettered buttons A thro
48. ugh D which will then flash Clicking one of those buttons then associates the copied settings with that button so they are available for instant recall when that button is pushed later This makes it easy to A B or even AJBIC D multiple sets of process chain and processor settings Note though that these settings aren t stored in any saved presets or in the plug in context saved by the DAW Thus they are only useful for comparing tweaks made to settings in the course of a single session with your project Chain Chain Chain The heart of T RackS is its signal processing chain and the equalization and dynamics processing modules that occupy the slots in the chain Either a selected module in the chain or a graphic view of the processor chain itself will be depicted just below the controls at the top of the T RackS plug in The graphic view which is engaged via the Show Chain button makes it easy to see at a glance the layout of the parallel and serial portions of the signal chain as well as which modules are in each slot within the chain Clicking on any module brings it to the foreground for tweaking Before diving into the details of those individual modules it is worth mentioning that IK s orientation with T RackS is toward analog modeled processors They use two proprietary technologies to do this DSM Dynamic Saturation Modeling models the way analog circuits respond to a signal based on the content of the signal itself ov
49. urse this is also highly subjective The bottom line is this perceived loudness meter is quite valuable The notion of the loudness suggestions also seems quite valuable though your mileage may vary on the usefulness of the specific suggestions for your musical genre To the right of the peak perceived loudness and RMS meters are two meters aimed at monitoring stereo field information A phase scope is up on top with a phase correlation meter underneath With the phase scope either dots or lines are displayed on an X Y scope Signals present on only one channel of the stereo spectrum would display as 45 degree tilted lines with left tilting downwards i e from left to right and right tilting upwards A mono signal would appear as a vertical line while a signal that is 180 degrees out of phase would show up as a horizontal line Besides being able to configure whether lines or dots are used for the display you can also configure how long the readings stay on the scope Values range from persistent i e the values stay on the scope indefinitely to lightning Le the values are extremely momentary You can also configure whether the readings are normalized i e so even low level signals show up as full scale readings or not I might have preferred if there were an option for displaying persistent values and displaying momentary values at the same time for example using fainter readings for the persistent values and brig
50. utput and an output level knob to adjust the overall level of the EQ Both are located on the right side of the module The short of it is that the Linear Phase EQ is intended for making surgical modifications to the signal it is processing while keeping the effects of the filtering as transparent as possible It does that well If there is a downside it is the impact using the linear phase function of this module has on plug in latency However that is par for the course with a linear phase equalizer not unique to T RackS The bottom line is that while you could pretty much count on T Rack flavoring your sound with earlier versions of T RackS the Linear Phase EQ is the first of several new T RackS modules that provides the option for transparent mastering Vintage Equalizer EQP 1A Transparent mastering may well be possible in T RackS 3 Deluxe but that doesn t mean you have to go down that route or that all new modules lean in that direction Also new on T RackS 3 Deluxe s plate of EQ offerings is the Vintage Equalizer EQP LA T RackS EQP 1A module is modeled on the classic Pultec EQP 1A program equalizer which is known not only for its musically pleasing sound but also for imparting its own flavor even when EQ settings are left flat IK injected a bit of humar in their modeling by making the visual look of this vintage EQ include physical defects akin to what a unit that had been bumped around might have Never trust a pris
51. would be when mastering a whole bunch of audio files that are likely to need identical processing for example perhaps instrumental cue mixes in a similar style Let s take a look at the additional facilities the standalone version of T RackS brings to the table When T RackS is launched as a standalone application there is an additional screen area down at the bottom of the user interface as compared with the plug in version This additional area provides access to a number of file Originally published on CakewalkNet com March 6 2008 Page 14 handling functions as well as a few audio processing functions that would normally be handled by the DAW when using T RackS as a plug in Over in the bottom left hand corner are the audio file handling functions These include a file list and buttons to add Load and remove files from the list T RackS 3 allows loading WAV AIFF CAF SD2 and MP3 files Once you ve added your files to the file list clicking on any file within the list selects that file for processing and loads it into the audio wave window that consumes the right hand side of the pane The audio wave window allows setting heads and tails trimming points fade regions i e the end of a fade in and the beginning of a fade out and the type of fade curve to be applied There are four types of fade in curves and three types of fade out curves available Zoom capabilities provided by small plus and minus signs in the lower l
52. you if you d used the Classic T RackS EQ in Slot 1A and wanted to automate its gain parameters Third and perhaps most significantly the Automation setup is T RackS wide not tied to a T RackS level preset Thus if you set up an automation configuration for a particular preset you will use over and over and save the preset then create another preset with different modules in spaces you d automated in the earlier preset and create automation settings for that Your automation assignments from the first preset will have been lost SONAR s VST plug in support does provide a workaround for this because it does save the T RackS wide parameters including automation mappings in its VST plug in level presets I would expect other DAWs may provide similar capabilities It is worth noting too that automation assignment changes you make within a given SONAR project will be preserved across sessions of the project so this concern is specific to using the same T RackS level preset in different projects The bottom line is it would seem a lot more logical to me if T Racks directly provided the ability to save automation setups with its own presets Their being tied to slots and modules within those slots means a whole lot of extra setup each time you change presets or change modules within slots and saving these values at the preset level could at least minimize that somewhat However this setup shouldn t adversely affect any given project once you have con
Download Pdf Manuals
Related Search