CHAPTER I CHAPTER II
Contents
1. for Cap Adjustment 2 pcs Screws for Mount 2 pcs Screws for Mount with Spacer 9 Spacer 10 Knob Switch 11 Screw Adjustment 2 pcs 12 Knob Torque on Mount QRP2 13 Lens Cover Bikini 14 Allen Wrench for screws pos 6 and 7 15 Anti Reflection Device ARD CHAPTER II OPERATION UNDER NORMAL CONDITIONS 2 1 ASSEMBLY AND PREPARATION FOR USE WARNING Ensure the weapon is unloaded and the safety selector is in the safe position before attempting to install remove or perform maintenance on the sight 2 1 1 Installing Battery a Remove Cap Battery 4 by turning it counter clockwise b Insert a AA size battery with negative end toward cap Caution while replacing battery not necessary when the sight is new Before installing Cap Battery inspect that the O ring is present and not damaged Failure to do so could result in water leakage into the battery compartment c Install Cap Battery by turning clockwise until snug Hand tighten only Using tools could damage equipment d Verify that red dot is present by turning the Knob Switch 10 clockwise 2 1 2 Installing Sight on the weapon The CompM4s Sight is designed for installation on most types of weapons which have a MIL Std 1913 Picatinny Rail Depending on type of weapon the optical line of sight the centre of the lens system may have different optimal height over the mounting rail The height of the optical axis of the Sight alone2. CHAPTER 1 1 PRESENTATION Aimpoint CompM4s Reflex Sight is a rugged precision red dot Sight developed mainly for military and law enforcement applications Aimpoint red dot sights are designed for the two eyes open method of sighting which greatly enhances situational awareness and target acquisition speed Thanks to the parallax free design the dot follows the movement of the user s eye while remaining fixed on the target eliminating any need for center ing Further the Sight allows for unlimited eye relief and is compatible with st 2nd and 3rd generation night vision devices The CompM4s Sight is using a AA size battery which together with the ex tremely low power consumption gives an unequalled battery life The CompM4s combines the superior accuracy and ease of use of the well known CompM2 model with significantly longer battery life and increased ruggedness through reinforced design The Sight is provided with a torque knob Quick Release QRP2 mount The Sight has a Spacer system that gives optimal height of the line of sight optical axis on different weapons 1 2 SPECIFICATION Extruded high strength aluminum Surface finish Hard Anodized black to dark graphite grey matte Material lens covers Rubber black Optical magnification 1X Eye relief Unlimited no centering required Optical coating Anti Reflex coating all surfaces Multi layer coating for reflection of red light 650 nm Band Pass c
3. d position Normally this means that only small adjustments are necessary providing that the weapon rail Picatinny Rail or carrying handle is properly aligned CAUTION Do not continue to adjust windage and elevation mechanisms if you encounter resistance The elevation adjustment screw is located on top of the sight while the windage screw is located on the right side a Open remove front and rear Lens Covers 13 b Turn the Knob Switch 10 clockwise until the red dot has a sufficient intensity to contrast against the target c Remove the the Caps Adjustment 1 for windage and elevation NOTE Each click of the Screw Adjustment 11 corresponds to a 16 mm movement of the point of impact at 100 meters 4 mm at 25 meters and 32 mm at 200 meters or 12 at 80 yds d Insert adjustment tool coin screwdriver knife or cartridge casing in adjustment screw slot and turn as follows e To move the point of impact to the right turn windage adjustment screw counter clockwise e To move the point of impact to the left turn windage adjustment screw clockwise e To move the point of impact up turn elevation adjustment screw counter clockwise e To move the point of impact down turn elevation adjustment screw clockwise e Confirm zeroing by firing at least three shots at a zeroing target Check points of impact on zeroing target to confirm accuracy and repeat above procedure if required f After initial firing ensure tha
4. oating for NVD compatibility Material housing Dot size 2 MOA Switch dot brightness 16 positions 7 NVD 8 daylight and 1 Extra Bright Battery One AA size battery rechargeable 1 2V alkaline lithium 1 5V or lithium 3 3 7V acceptable voltage 1 2 5 0 V Battery life Length Width Height Weight Adjustment Mounting Height of optical axis Max temperature range Water resistance NVD MOA Minute Of Angle Over 8 years of continuous day and night use at pos 12 of 16 and over 3 years at pos 13 of 16 at room temperature and with a quality battery Typically 500 000 h at NVD setting 135mm 5 3 75mm 3 61mm 2 4 with Spacer 70mm 2 8 370g 13 1 oz with Spacer 395g 14 oz Range 2 m at 100 meters 2 yds at 100 yds in windage and elevation 1 click 4 mm at 25 meters 16 mm at 100 meters 1 2 at 80 yards On a MIL Std 1913 Picatinny Rail A Spacer is available for optimal height 30 mm 1 2 with QRP2 mount 39 mm 1 5 with QRP2 mount and Spacer 45 C to 70 C 50 F to 160 F in storage and operation Submersible to 45 m 150 ft Night Vision Device 1MOA 30 mm at 100 meters or 1 at 100 yards Over top surface of Picatinny Rail 1 3 LOCATION AND DESCRIPTION OF MAJOR COMPONENTS See figure next page Cap Adjustment 2 pcs Battery AA size Cap Battery Strap for Cap Battery Soa SS 2 pcs Mount QRP2 o Strap
5. r 4 2 IMPOSSIBLE TO ZERO Adjustment screw is at its limit Check alignment of rail or carry handle to barrel Impact point is moving Check Mount and weapon rail or carry handle stability CHAPTER V MAINTENANCE a This Sight does not require any particular maintenance while used under normal conditions b Under severe weather conditions please refer to chapter III c Keep Lens Covers closed whenever the sight is not in use d Warehouse storage Remove battery and allow lens surfaces to dry completely if wet before closing the lens covers e To clean lenses refer to CAUTION in chapter III gt Aimpoinr SE 213 75 Malmo Sweden Phone 46 0 40 671 50 20 Fax 46 0 40 21 92 38 e mail info aimpoint se www aimpoint com 2007 Contents property of Aimpoint All rights reserved Art No 12171 Operator and Maintenance Manual for Aimpoint CompM4s including QRP2 Spacer amp killFlash Aimpoint AB Aimpoint Inc Jagershillgatan 15 14103 Mariah Court Chantilly VA 20151 2113 USA Phone 1 703 263 9795 Fax 1 703 263 9463 e mail info aimpoint com www aimpoint com THE FUTURE IN SIGHT
6. t the Mount and Sight are secure g Turn Knob Switch 10 to OFF position counter clockwise h Close front and rear Lens Covers CHAPTER IlI OPERATION UNDER EXTREME CONDITIONS a Extreme heat moist or dry No special procedures required b Extreme cold Extreme cold might shorten battery life c Salt air No special procedures required d Sea spray water mud and snow Ensure that Cap Battery 4 and the two Caps Adjustment 1 are tightened before exposing the sight to sea spray mud snow or before immersing the sight in water Hand tighten only Keep Lens Covers closed when sight is not being used Clean lenses with lens paper cloth and wipe the sight dry as soon as possible after exposure to water sea spray mud or snow e Dust storms and sand storms Keep Lens Covers closed when sight is not being used f High altitudes No special procedures required CAUTION The lenses shall never be cleaned with fingers but with lens paper cloth If no lens paper cloth available To clear away debris sand grass etc blow away the dirt To clean lenses mist up the lenses and clean them with a soft piece of cloth CHAPTER IV TROUBLE SHOOTING PROCEDURES 4 1 RED DOT DOES NOT APPEAR Discharged battery Replace battery Battery installed incorrectly Remove and reinstall battery with toward cap Battery is not making contact Clean contact surfaces and reinstall battery Defective Knob Switch Notify dealer armoure
7. without Spacer is 30 mm 1 2 With the Spacer 9 mounted the height of the optical axis is increased by 9 mm 0 30 a Assemble the Sight with the Mount QRP2 8 by means of the two short screws 6 and the Allen Wrench 14 Tighten firmly Some thread glue e g a light Loctite could be used on the screw threads See Fig A below or aa Assemble the Sight with the Mount QRP2 8 and the Spacer 9 by means of the two long screws 7 and the Allen Wrench 14 Tighten firmly Some thread glue e g a light Loctite could be used on the screw threads See Fig B below b Install the Sight to the weapon rail by using the Knob Torque 12 e gt Ensure that the Sight is correctly positioned and that the recoil stop fits into a groove on the Picatinny Rail To ensure that Sight is secure tighten Knob Torque 12 until it snaps twice c When using Lens Covers ensure that they are correctly positioned and can easily be opened removed d Finally make sure that the Knob Torque 12 is firmly tightened around the weapon rail e Complete zeroing according to 2 2 1 gt Fig A without spacer Fig B with spacer 2 1 3 Lens Covers In order to preclude the loss of the Lens Covers when removed from the optical path of the Sight the Lens Covers should be removed downwards The rubber string will then attach around the Sight and mount 2 2 OPERATING PROCEDURES 2 2 1 Zeroing The Sight is delivered in a centere
Download Pdf Manuals
Related Search