Source Four PAR
Contents
1. e Enterprise Square 9 Sheung Yuet Road Kowloon Bay Hong Kong e Tel 852 2799 1220 e Fax 852 2799 9325 World Wide Web http www etcconnect com Email mail etcconnect com Specifications subject to change Source Four PAR is protected by US patent numbers 5 268 613 US and International Patents Pending 70611001 Copyright 1998 Revised 11 982. lamp if it becomes damaged or deformed Verify that the HPL lamp you use is suitable for the voltage at your facility 115 120 230 and 240 volt HPL lamps are available fF HPL lamp Caution Operating lamps above their rated voltage reduces lamp life and can cause premature lamp failure 1 Disconnect the unit from power before installing the lamp Lamp brackets WARNING Let lamp cool before changing DIN 2 Loosen the knurled bolt on the back of the lamp housing and pull the housing UON straight out from the back of the fixture 3 Remove the HPL lamp from its box holding it by the base Knurled bolt 7 Note To avoid premature lamp failure do not touch the lamp glass with your fin gers If you touch the lamp during installation clean it carefully with rub bing alcohol and a clean lint free cloth before operation 4 Line up the flat sides of the lamp base with the brackets on either side of the socket Figure 1 5 Push down on the lamp base until the lamp is firmly seated Make sure that the lamp is fully seated with the bottom of the lamp heat sink flush to the lamp housing casting Caution Improperly installed lamps cause premature lamp failure and socket problems 6 To reinstall the lamp housing center it on the reflector and the bolt hole then tighten the knurled bolt to secure the lamp housing in place Lamp housing Figure 1 2 e Source Four PAR Lens identificatio
3. n Lenses for the Source Four PAR come in four versions The type or beam spread can be identified by the lens texture VNSP NSP Ol Q Very narrow spot Narrow spot Clear glass Stipple glass slight diffuse texture 15 Round beam shape 19 Round beam shape MFL WFL a E Changi W A j edium flood Wide flood Fewer facets sized 6 x 22mm Many facets sized 6 x 12mm 21 x 34 Oblong beam shape 30 x 51 Oblong beam shape ng Source Four PAR lenses Change lenses if they become cracked or badly scratched Re Caution Never operate the Source Four PAR without a lens in place moving a lens WARNING Unplug the fixture before attempting to remove or install a lens N OO A 8 Source Four PAR lenses get hot while the unit is in operation Let the fixture cool before handling the lens Place the fixture on a flat stable work surface Do not install or remove lenses with the unit hanging Position the lens rotation ring with the spring clip at the top of the unit directly below the retaining clip Tilt the front of the fixture down at least 45 degrees Press the spring clip with your finger to release the lens Figure 2 Allow the lens to dr
4. ng clip opens 2 Insert the color frame 3 Press the retaining clip down until it locks Note Use only color frames or top hats with 6 7 inch inside diameter Cleaning the reflector Figure 5 ETC offers the following recommendations when cleaning and inspecting lenses and reflectors Do not use glass and window cleaners on the reflector Chemicals in these cleaners will harm the reflective coating Do not use paper towels or harsh materials to wipe the reflector These materials can scratch the surface of the reflector WARNING Unplug the fixture before attempting to clean reflector 1 Remove the lens so you can access the reflector from the front of the fixture See Removing a lens on page 3 2 Remove dust with a blast of oil free air or wipe with a clean soft lint free cotton cloth If this is sufficient to remove dust go to step 5 Otherwise continue to step 3 3 Dampen a clean soft lint free cotton cloth with a mild soapy water solution and gently wipe the reflector 4 Remove any soapy water residue with a clean soft lint free cotton cloth dampened with water 5 Reinstall a lens before using the fixture Electronic Theatre Controls North America 3030 Laura Lane Middleton Wisconsin 53562 USA e Tel 1 608 831 4116 Fax 1 608 836 1736 Europe 5 Victoria Industrial Estate Victoria Road London W3 6UU e Tel 44 181 896 1000 Fax 44 181 896 2000 Asia Room 605 606 Tower Ill
5. op forward from under the clip When the lens drops remove your finger allowing the lens to slide forward until it rests on the lens catchers Figure 3 Carefully remove the lens from the fixture Installing a lens 1 Position the fixture with the front of the unit the lens side facing you and tilted slightly Figure 2 Position the lens rotation ring with the spring clip at the top of the fixture directly below the retaining clip Hold the lens by the edge and position it so the convex side faces the back of the fixture Figure 4 Note nstalling the lens with the convex side out will not impair the optics but it will make removing the lens difficult From the top of the fixture slide the lens behind the lens catchers and position its base behind the tabs on the bottom of the lens rotation ring Gently push the top of the lens inward until it snaps behind the spring clip Spring clip ss eo Tab WZ Retaining clip Figure 2 BY Lens catcher Figure 3 Retaining clip Spring clip Tab Figure 4 Source Four PAR e 3 Color frame retaining clip The color frame holder is equipped with a spring loaded retaining clip that prevents color frames and accessories from falling out WARNING Hang the Source Four PAR with the color frame retaining clip Retaining clip in in the locked position _ the locked position Q 1 Release the retaining clip by pushing it sideways The retaini
6. ource Four PAR Lens Color frame L Source Four PAR Please note the following safety warnings before use Do not mount the Source Four PAR on or near combustible surfaces Do not operate the Source Four PAR without a lens installed e Always hang the Source Four PAR with the color frame retaining clip in the locked position Accessories Color frame 75 in sq 6 7 in inside diameter 407CF Safety cable 31 in 400SC C clamp 400CC Very Narrow Spot lens 400 VNSP Narrow Spot lens 400 NSP Medium Flood lens 400 MFL Wide Flood lens 400 WFL Set of four Source Four PAR lenses VNSP NSP MFL WFL saute Source Four PAR 1 HPL lamps Use the HPL lamp only in Source Four and Source Four PAR fixtures manufactured and sold by Electronic Theatre Controls Inc Do not use lamps other than the HPL in Source Four PAR fixtures Lamp code Watts Volts Color temp Ave rated life HPL 375 115 375 15 3 250 K 300 hour HPL 375 115X 375 115 3 050 K 1 000 hour HPL 550 77 550 77 3 250 K 300 hour L550 77X 550 77 3 050 K 2 000 hour mIPIL iAeyAlile E575 15 3 250 K 300 hour HPL 575 115X 575 115 3 050 K 2 000 hour HPL 575 120 575 20 3 250 K 300 hour HPL 575 230 575 230 3 200 K 400 hour HPL 575 240 575 240 3 200 K 400 hour American I U Euro Installing the HPL lamp Always replace the
Download Pdf Manuals
Related Search