Digital Terrestrial Receiver SRT 8010
Contents
1. Enter to the menu by pressing OK button If USB memory module inserted correctly then you can start update by pressing OK button In case files on USB memory module are correct the update will start You will see progress of update on screen A Warning Do not power off your receiver during update process This may damage your receiver 5 4 5 Factory Reset Use this function only in case of needs to return to the factory settings This function will erase all channels favourite lists and your personal preferences To activate factory reset you will need to enter PIN code After factory reset receiver will appear with first time installation wizard 6 0 DAILY OPERATIONS 6 1 Electronic Program Guide EPC Electronic Program Guide available from live view mode It displays program information if supported by broadcast To enter to Electronic Program Guide press EPG button on remote control In this menu screen divided to 3 parts at the left represented channel list at the right represented program schedule at the bottom displayed short details of selected program In the channel list select channel using buttons A V Use buttons lt P to switch between channel list and program schedule To display program schedule for following previous day use GREEN RED buttons To display details of selected program press OK or Info button Use buttons A V to scroll information in program details mode To setup Timer to selected program use YELLOW2. PART 1 s English STRONG DIGITAL TV Remote control Batteries are discharged or not Check correct installation of the batteries doesn t work correct installed Change batteries Message Antenna Short cut in cable between Disconnect receiver from main power Check circuit overload on antenna and receiver or the cable between receiver and antenna screen antenna is out of service Replace cable or and antenna A 2 SPECIFICATION Tuner Input connector Type IEC60169 2 female 75 Ohm Input freguency range VHF 174 MHz 230 MHz UHF 474 MHz 858 MHz Bandwidth 6 7 and 8 MHz Input signal level 82 20 dBm Signal spectrum COFDM transmition modes 2K 8K Antenna power 5 V DC max 50 mA short cut protected Demodulation Demodulation modes OSPK 16 QAM 64 QAM Guard interval 1 4 1 8 1 16 1 32 Error correction 1 2 2 3 3 4 5 6 7 8 Video decoder Profile H 264 AVC Main Profile and High Profile Level 3 for H 264 AVC and MPEG 2 Main Profile Main Level for MPEG 2 Input bit rate Max 90 Mbit s Aspect ratio 4 3 16 9 Pan amp Scan Letterbox Frame rate 25 Hz for PAL and SECAM 30 Hz for NTSC Resolution 720 x 576 for PAL and SECAM 720 x 480 for NTSC Audio decoder Audio compression modes MPEG 2 Low Complexity AAC LC AAC MPEG 4 High Efficiency AAC HE AAC MPEG 2 Layer II MPEG 1 Layer I MPEG 1 Layer II Audio modes Mono L R Stereo Dolby Digital dd Freguency response 20 Hz 20 k
3. Select Appearing order if broadcast in your country does not support logical channel numbering or select Operator defined if broadcast in your country supports logical channel numbering If you are not sure which option to select please consult to your dealer To store changes press GREEN Save button 13 www strong tv S 700NG PART 1 s English DIGITAL TV 5 3 Preferences In this menu you can setup preferred menu language audio and subtitles languages setup video output time settings and tune some options of OSD display 5 3 1 Language Select OSD language audio and subtitles languages To select language use buttons lt P or press OK to display list of available options and select language by A V buttons Press GREEN Save to store changes 5 3 2 TV Output To select value use buttons lt P or press OK to display list of available options and select value by AW buttons To store changes press GREEN Save button To discard changes press EXIT TV Standard setup accordingly to standard used by your TV set Please consult to the User Manual of your TV set Tips in case of picture disappears from screen and not appeared in 15 seconds press EXIT 7 2 times Such a problem may appear if your TV set do not supports selected standard Aspect ratio setup accordingly to aspect ratio of your TV set Conversion mode it is recommended to use Letter Box If broadcast include channels for different aspec
4. STRONG DIGITAL Digital Terrestrial Receiver SRT 8010 User Manual PART 1 o English A 7720NG DIGITAL TV TABLE OF CONTENTS 1 0 INTRODUCTION 2 1 1 Safety Instructions 2 1 2 Storage 2 1 3 Equipment Set up 3 1 4 Features amp Accessories 3 2 0 YOUR RECEIVER 4 2 1 Front panel 4 2 2 Rear panel 5 2 3 Remote control 6 3 0 CONNECTION 7 3 1 Connecting to terrestrial antenna 7 3 2 Connecting to TV set 7 3 3 Connecting to digital audio amplifier 8 3 4 Connecting of external USB memory device 8 4 0 FIRST TIME INSTALLATION 8 4 Language select 8 4 2 Terrestrial settings 8 4 3 Preferences 9 4 4 Adjust antenna 9 4 5 Channel setup 9 5 0 MAIN MENU 10 5 1 Channel organiser 10 5 2 Installation 12 5 3 Preferences 14 5 4 Setup 15 6 0 DAILY OPERATIONS 16 6 1 Electronic Program Guide EPG 16 6 2 Channel information 17 6 3 Channel list and view mode 17 A 1 TROUBLE SHOOTING 18 A 2 SPECIFICATION 19 HOTLINE EF 0180 500 75 43 0 14 Min from German wired line EE 0820 400 1507 0 12 Min from Austrian wired line per February 2008 www strong tv L lt S7RONG PART 1 English DIGITAL TV 1 0 INTRODUCTION 1 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER m ina closed or poorly ventilated cabinet directly on top of or under any another equipment on a surface which might obstruct the ventilation slots DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES m To direct sunlight or near any
5. button Timer setup described in part 5 4 1 of this manual To return from EPG mode to live view mode press EXIT 16 www strong tv PART 1 o English STRONG DIGITAL TV 6 2 Channel information Information banner displayed on screen every time when you zap channel in live view mode It displays information about channel type TV or Radio date and time information channel number and name start time and name of the present and following program on the channel As an icons displayed information about availability of subtitles Teletext audio mode and screen format of the current program Information banner can be invoked on screen by pressing to INFO button If you press INFO button 2 times then information banner will display technical parameters of the current channel and signal level and quality indicators 6 3 Channel list and view mode To display current channel list press OK button To select channel use buttons A V ED To zap to selected channel press OK button and to switch to full screen press OK button again 6 3 1 Fast alphabet filtering In channel list mode press RED Filter button to filter channels in alphabet order At the right side alphabet will be displayed Select first letter of the channel name that you need to find in the list and press OK 6 3 2 Favourite list selection To change to Favourite mode press FAV button from full screen view mode or channel list mode On screen will be displayed list
6. mode CR error correction Const modulation mode GI guard interval All parameters are detected automatically Below of the table with broadcast parameters displayed bars indicated signal level and guality of selected broadcast channel To start scan on all broadcast freguencies press GREEN Auto scan button To scan one or several broadcast freguencies select freguency using A Y buttons and press OK to select it Repeat this for all freguencies you wish to scan Press RED Scan selected button to start scan process At the end of scan process you can select one of the options described in part 5 2 1 5 2 4 Terrestrial Setting In the menu Terrestrial Setting you should setup parameters that allow receiver to function correctly in your area Use buttons lt P A V to navigate and selection of Country Antenna Power and Channel numbering Use button OK to display lists of available options Country Select country where receiver is installed Parameters of broadcast are different from country to country and this parameter is very important Change of country will delete all installed channels and you need to scan them again Antenna power Select Enabled if you do use active antenna with support of power injection through coaxial cable Make sure your antenna supplied by 5 V DC and earns not more than 50 mA If you use passive antenna or your antenna is powered by an external power select Disabled Channel numbering
7. At the right part of screen displayed list of favourite channels it is empty by default Header of this part displays name of favourite group and number of channels To select favourite group use FAV button To switch between all channels list and favourite list parts use buttons lt gt Add channel to the favourite group To select channel use A V buttons and press OK to confirm your choice Name of the selected channel will appear in favourite group Add in same way other channels to favourite groups To store changes press GREEN Save button www strong tv 11 9 720NG PART 1 English DIGITAL TV Remove channel from favourite group Use button FAV to select favourite group where you wish to remove channel Use button to move menu focus to the right part of screen favourite group content Use buttons A Wto select channel that you would like to remove and press OK to confirm To store changes press GREEN Save button 5 2 Installation Menu Installation consist of following submenus Auto Scan Manual Scan Advanced Scan and Terrestrial setting In first order make sure that all Terrestrial Settings are corresponds to broadcast parameters in your area 5 2 1 Auto Scan Select this item and press OK to start automatic scan of all channels broadcasted in your area During search process on screen will be displayed following information scanned frequency number of scanned frequencies total number of fr
8. Hz lt 2 dB 60 Hz 18 kHz lt 0 5 dB Sampling rate 32 44 1 48 kHz www strong tv 19 lt gt 7RONG PART 1 e English DIGITAL TV System and memory CPU Flash memory SDRAM memory Connectors Antenna input ANT IN LOOP through output TO TV STi5202 4 MByte 64 MByte TV SCART RGB CVBS audio left and right with volume control 3 RCA S PDIF optical USB General characteristics Input voltage range Power consumption Operating temperature Storage temperature Operating temperature range Size W x Dx H Weight Video Audio Left and Right 2 0 type A 100 240 AC 50 60 Hz max 12 W 5 40 C 20 70 C 10 85 RH non condensing 260 x 190 x 45 mm 1 2 kg Subject to alterations In consequence of continuous research and development technical specifications design and appearance of products may change All product names are trademarks or registered trademarks of their respective owners STRONG 2008 All rights reserved 11 2008 20 www strong tv Environmental Issues STRONG ENVIRONMENTAL ISSUES STRONG is committed to reducing the impact of its products on the environment To maximise the benefits of our design enhancements your co operation is required Electronic product recycling Do not dispose of this product with your domestic rubbish At the end of its useful life this product contains materials which when processed corr
9. Make sure that power cord is connected to the mains power Power on your receiver then turn on your TV set On TV screen will be displayed menu Select your language of the installation wizard The installation wizard will help you to quickly setup your receiver and start to watch programmes 4 1 Language select Use buttons A Y to select your language and press OK to continue 4 2 Terrestrial settings This menu allows you to setup settings specific for your country Use buttons A V to select options and buttons lt P to change values Country select country corresponded to place of installation If country is not in the list select Other Antenna power select Enabled if you do use active antenna with support of power injection through coaxial cable Make sure your antenna supplied by 5 V DC and earns not more than 50 mA If you use passive antenna or your antenna is powered by an external power select Disabled 8 www strong tv PART 1 o English STRONG DIGITAL TV Channel numbering select Appearing order if broadcast in your country does not support logical channel numbering or select Operator defined if broadcast in your country supports logical channel numbering If you are not sure which option to select please consult to your dealer To continue installation select Next and press OK 4 3 Preferences In this menu you can setup your preferences Use buttons A V to select option an
10. Settings Parental Control is Enabled To remove channel lock press OK button again on the group of channels and store changes by pressing GREEN Save button Operations under single channel To execute operations under single channel move menu focus to the right part of screen Channel list All operations under single channel are same as for groups of channels Difference is only in sort function Single channel can be moved to selected position in the list Channel move Select channel that you wish to move to new position and press YELLOW Sort button At the right side from channel name will appear symbol AW Use buttons A W to move channel to new position and press OK to confirm new position To store result press GREEN Save button Channel rename Select a channel you wish to rename and press BLUE Rename button On screen will be displayed alphabet Use buttons lt P AV to navigate between symbols and button OK to select add to the name To delete symbol from the name select character 4 and press OK To toggle between Latin and Cyrillic alphabet use RED Lat Cyr button To store changes press GREEN Save button to discard changes press EXIT 5 1 2 Favourite manager In this menu you can prepare favourite lists At the left side of screen displayed list of all channels Header of the list shows type of channels TV or Radio and number of the channels in the list To toggle between TV and Radio use TV R button
11. TV and All Radio will delete these channels from favourite groups as well Delete of all channels from favourite groups would not delete channels from groups All TV and All Radio A Warning after press to GREEN Save button all channels from selected group will be deleted It is not possible to undo this operation Save GREEN Pressing to this button will save changes made in the channel groups Sort YELLOW Use this button for automatic sorting channels in selected group Alphabet A Z channels will be sorted in alphabet order Frequency Low High channels will be sorted in frequency order first will be placed channels broadcasted on low freguencies then channels broadcasted on higher freguency First FTA Free To Air channels will be placed at first positions of the list scrambled channels will be placed at the end of the list First Scrambled Scrambled channels will be placed at first positions of the list FTA channels will be placed at the end of the list To store changes press GREEN Save button 10 www strong tv PART 1 o English STRONG DIGITAL TV O Tips Channels are sorted only in selected list Sorting of the channels in one list would not cause change of order in other lists To Lock access to all channels in selected group press OK and save changes by pressing GREEN Save Viewing of locked channels will require entering of the PIN code if option Service Lock in menu
12. d buttons lt P to change values Audio language and Subtitle language select accordingly to your preferences The receiver will automatically select preferred language if it is present in broadcast Aspect ratio setup accordingly to aspect ratio of your TV set Conversion mode it is recommended to use Letter Box If broadcast include channels for different aspect ratio then your TV set then receiver will convert video in such a way that complete video picture fits to screen In Pan Scan mode geometrical proportions of picture would not be changed however part of video will be truncated Summer time set to On during summer time day light save period or OFF during winter time To continue installation select Next and press OK 4 4 Adjust antenna This menu allows you to select best location and direction of your antenna especially when you use indoor antenna Channel select channel where available digital terrestrial broadcast at your location Please consult to your dealer for details Bandwidth digital terrestrial broadcast uses bandwidth 8 MHz for channels 21 69 Bandwidth 7 MHz used for channels 5 12 Adjust if necessary position and direction of your antenna to get maximum levels of signal level and quality To complete installation and start channel search process select Next and press OK 4 5 Channel setup Channel setup process will take few minutes Once it is completed the receiver will stor
13. des complete instructions for installing and using this receiver The following symbols will serve as follow Warning Indicates warning information Tips Indicates any other additional important or helpful information MENU Represents a button on the remote control or the receiver Move to Represents a menu item within a window 1 4 Features amp Accessories Features m For all digital Free To Air TV and Radio programmes with outdoor or indoor terrestrial antenna Support of MPEG 4 and MPEG 2 standards in standard definition DVB T compliant Digital UHF VHF Tuner with Loop through function Set up support for first time installation Quick and easy installation amp user friendly menu Multi lingual support on screen Menu Excellent Audio and Video quality Digital audio output through optical S PDIF Automatic and manual channel scan options Support of active antenna by 5 V output Support of channel numbering defined by broadcaster 500 channels memory capacity Favourite lists for TV and Radio Parental lock function for menu selectable per channel Electronic Program Guide EPG for present following event information and up to 7 days for on screen programme information 3 Operation Modes Digital TV Digital Radio Favourite Support of Teletext OSD amp VBI Multi lingual subtitling and audio track support Timer programmable via EPG Edit function for channel names Connections ANT IN antenna input TO TV Loop through ou
14. e found channels and switch to live view with channel number 1 Now installation is completed and you can enjoy digital TV and Radio www strong tv 9 S 7700NG PART 1 English DIGITAL TV 5 0 MAIN MENU All settings of the receiver can be done in Main Menu Main menu consist of Channel organiser Installation Preferences and Setup To access to the Main Menu press button MENU on the remote control 5 1 Channel organiser Using buttons lt P select item Channel organiser In this menu you can sort and edit channels as well as manage Favourites Use buttons A V to select submenu and press OK 5 1 1 Service Manager In this menu you can sort channels move channels to wished position delete lock or rename channels At the left part of screen displayed list of channel groups All TV channels All Radio channels and 8 Favourite groups At the right part displayed list of the channels included to relevant group To switch between parts of screen and as a result between operations under channel group and operations under single channels use buttons lt gt Operations under groups of channels Use buttons A Y to select group of channels Delete all To delete all channels included to selected group of channels press RED Del All button All channels included to selected group will be marked to delete Delete operation will be executed after pressing to GREEN Save button Delete of all channels from groups All
15. econds after switching off the receiver before you move the receiver or disconnect any equipment m Itis a necessity that you only use an approved extension and compatible wiring that is suitable for the electrical power consumption ofthe installed equipment Please ensure that the electrical power supply corresponds with the voltage on the electrical identification plate at the back of the receiver If the receiver does not operate normally even after strictly following the instructions in this user manual it is recommended to consult your dealer 1 2 Storage Your receiver and its accessories are stored and delivered in a packaging designed to protect against electric shocks and moisture When unpacking it make sure that all the parts are included and keep the packaging away from children When transporting the receiver from one place to another or if you are returning it under warranty make sure to repack the receiver in its original packaging with its accessories Failing to comply with such packaging procedures could void your warranty 2 www strong tv PART 1 s English STRONG DIGITAL TV 1 3 Equipment Set up We recommend you consult a professional installer to set up your equipment Otherwise please follow the instructions below m Refer to the user manual of your TV and your antenna m Make sure that the SCART cable and outdoor components are in a good condition and the SCART connections are well shielded This manual provi
16. ectly can be recovered and recycled By participating in the responsible recycling of this product you will be reducing the requirement for new raw materials and reducing the amount of material that would otherwise end up in landfill When you purchase a new similar product your retailer may offer to take this old one off you Alternatively you can take it to your local recycling centre Your retailer or local municipal authority will advise you of the collection facilities available for waste electronically products in your area User of this service will be free to you Within the scope of the European legislation on Waste Electrical and Electronic Equipment Directive 2002 96 EC valid as of August 2005 STRONG provides a recycling system free of charge for consumers to returning products after end of life For more information about STRONG s environmental policy to you www strong tv select About us and Environmental Policy from the submenu DIGITAL TV Packaging i A on When disposing of this st KA 2 product packaging please ensure that it is recycled Packaging material is to be depolluted in waste separation Power Saving To save power and money please put the product into standby mode when not in use We also recommend disconnection from mains supply when not in use for longer periods of time Batteries Do not dispose of the batteries AR from your handset with your domestic waste ut W
17. en Power ON and OFF This option not available if Action of timer set to Power On or Power Off Channel press button OK to display channel list In the channel list use navigation buttons to select channel and OK to confirm selection You can use button TV R to switch between TV and Radio channels To store settings of Timer press GREEN Save button To discard changes press EXIT 5 4 2 Parental control In this menu you can setup restriction of access to menu and Enable Disable lock of the channels that are marked as locked in the channel organizer Menu Lock Disabled by default If you wish to lock access to Menu then set this option to Enabled Service Lock Enabled by default Viewing of the channels marked as locked possible only after entering PIN code If you wish to disable lock of access to locked channels then set this option to Disabled Change Password In this menu you can change your password PIN code Select this option and press OK On the factory PIN code is set to 0000 If you forgot your PIN code call to service support www strong tv 15 A 720NG PART 1 English DIGITAL TV 5 4 3 System Info Select this item and press OK to get information about installed software version and hardware version in your receiver 5 4 4 Software update Before enter to this menu you need to insert USB memory module to USB port at the back of your receiver Files with new software should be copied to USB memory module
18. equencies number of found channels and their names At the end of scan process you will have possibility to select one of the options m Store found channels and switch to live view mode by pressing OK button m Store found channels and return to menu by pressing MENU button m Discard channel search result and return to menu by pressing EXIT button In case of no channels found the receiver will display corresponded message In such a case make sure that antenna is connected to the ANT IN connector Repeat auto scan after all connections are checked 5 2 2 Manual Scan This function can be used in case of broadcast is present on not standard frequency Select this item and press OK Manual Scan menu will be displayed on screen Frequency using buttons 0 9 enter frequency in KHz for example 474000 Bandwidth using buttons lt gt select channel bandwidth Make sure that signal level and quality are acceptable more than 50 and press GREEN Start Scan button At the end of scan process you can select one of the options described in part 5 2 1 12 www strong tv PART 1 s English STRONG DIGITAL TV 5 2 3 Advanced Scan This function can be used if necessary to find new channels on already installed frequencies or on one of the new frequencies of broadcast Select this item and press OK In Advanced Scan displayed information about broadcast channel MUX frequency in KHz and other technical parameters TX transmission
19. here they are available participate in your local municipal or retailer collection schemes for spent batteries Batteries discarded in landfill sites or incinerated increases the chances of pollutants being dispersed into the atmosphere Alternations reserved 12 2008 www strong tv lt gt 7RONG Environmental Issues DIGITAL TV www strong tv
20. menu or sub menu and cancels the progressing function if applicable 10 A Y For zapping to next previous channel in live view mode for navigation up down in Menu mode 11 4 gt S D For increasing decreasing volume level in live view mode for change selected option in Menu mode 12 OK Displays channel list in live view mode to confirm selection in Menu mode 13 RED RCL Switches back to to previous watched channel in live view mode content dependent function in Menu mode 14 GREEN Pause Freeze resume picture in live view mode content dependent function in Menu mode YELLOW Sub Displays list of available subtitles languages in live view mode content dependent function 1 Un in Menu mode 16 BLUE Text Switches to Teletext mode in live view mode content dependent function in Menu mode 6 www strong tv PART 1 s English A 7RONG DIGITAL TV 17 FAV Displays list of Favourite groups 18 TV R Toggles between TV and Radio modes 19 EPG Displays Electronic Program Guide 20 0 9 To select channel bv number in live view mode to enter values of parameters in Menu mode 21 LIST To displav channel list in live view mode 22 ZOOM To zoom in part of live video 3 0 CONNECTION Terrestrial Antenna 000 L AUDIO R p gt gt gt 1 Sant IN TOTV 3 1 Connecting to terrestrial antenna To receive the broadcast signal the te
21. of favourite groups Use buttons A V to select group and press OK to confirm To return to all channel list mode select group All from the list To switch between TV and Radio modes use TV R button 6 3 3 Audio track and mode selection To select alternate audio track press button AUDIO on remote control On screen will be displayed list of available audio tracks Use buttons A V to select audio track To select audio mode stereo left right press button B and use buttons A V to select mode Press OK to confirm 6 3 4 Teletext In live view mode press button Text BLUE If channel broadcasted with Teletext in several languages then select language and press OK 6 3 5 Subtitles In live view mode press button Sub YELLOW On screen will be displayed list of subtitles languages Select language of your choice and press OK If you wish to disable subtitles then select OFF from the list www strong tv 17 STRONG PART 1 e English DIGITAL TV 6 3 6 Zoom part of video In live view mode press button ZOOM On screen will be displayed rectangle which represents area of screen to be enlarged Use buttons A V and lt P to move Zoom area To change Zoom ratio press ZOOM button again To activate Zoom function press OK To return to normal view mode press EXIT 6 3 7 Pause Press PAUSE button to freeze video Press this button again to return to live video 6 3 8 Recall To recall previous watched channel press RCL butt
22. on A 1 TROUBLE SHOOTING There may be various reasons for the abnormal operation of the receiver Check the receiver according to the procedures shown below If the receiver does not work properly after checking it please contact the dealer Don t open the receiver cover This may cause a dangerous situation Indicator ON OFF on front panel do not light up Video or Audio absent Message No signal on screen Power cord is not plugged to the wall outlet Power switch on the back of the receiver is in OFF position Not correct connection of cables between receiver and TV set TV Set is switched to a different input than the connected Bad connection between receiver and antenna Incorrect settings in Terrestrial setting Incorrect direction of antenna Check connection of the receiver to the mains Make sure to turn power switch on the back of the receiver to ON position Unplug all cables from receiver and TV set Connect them back again carefully Increase volume level press V button on remote control of receiver Increase volume level on TV set Switch ON your TV set Select the input accordingly Check connection of cable between receiver and antenna Check settings in menu Installation Terrestrial Setting Possible you do use active antenna but antenna power switched OFF Check signal level and guality Correct direction of antenna if necessary 18 www strong tv
23. other equipment that generates heat to rain or intense moisture to intense vibration and to any shock which may cause permanent damage to your receiver or to any magnetic objects such as loudspeakers transformers etc m Do not use a damaged power cord It may cause a fire or an electrical shock Do not touch a power cord with wet hands It may cause an electric shock m Never open the cover It is dangerous to touch the inside of the receiver due to high voltage currents and possible electrical hazards Your warranty will be void if the receiver has been opened m When the receiver is not used for a long period of time you should unplug the power cord from the wall socket m Do not use alcohol or ammonia based liquids to clean the receiver If you wish you may clean your receiver with a soft lint free cloth slightly made damp with a mild soap solution only after disconnecting from the mains voltage supply Make sure no foreign objects fall through the ventilation slots because this could cause fire or an electric shock m Do not place any objects on top of the receiver because this might prevent proper cooling of the components inside SAFETY PRECAUTIONS m Do notopen the receiver cover as you will be exposed to a shock hazard It will also void your warranty Refer all maintenance or servicing to suitably qualified personnel m When you are connecting the cables be sure that the receiver is disconnected from the mains supply voltage Wait a few s
24. rrestrial antenna cable should be connected to the ANT IN connector at the back of the receiver 3 2 Connecting to TV set Connecting with SCART cable Connect one end of SCART cable to TV SCART connector on the back of receiver Connect another end of SCART cable to SCART connector on vour TV set www strong tv A 720NG PART 1 English DIGITAL TV Connecting with AV cable On the back of your receiver you will find the RCA connectors Audio Left amp Right red amp white Video yellow Install an audio video cable between the RCA connectors of the receiver and those of your TV set or amplifier Tips if you have only one audio input on your TV set then connect Left White audio output 7 of the receiver to audio input of your TV set 3 3 Connecting to digital audio amplifier Connect one end of optical cable to S PDIF output of the receiver Connect another end of cable to S PDIF input of digital audio amplifier 3 4 Connecting of external USB memory device Extrernal USB memory device should correspond to USB 2 0 standard and it s power consumption should be not more than 500 mA External USB memory device can be used for software update see part 5 4 4 of this manual for details New software versions are published on the web site www strong tv support gt download 4 0 FIRST TIME INSTALLATION Check correctness of all connections If you are not sure ask professional installer to install your equipment
25. sh STRONG DIGITAL TV 5 4 Setup In this menu you can setup Timer for switching receiver ON OFF according to schedule block access to the receiver settings and channels get information about software and hardware version of your receiver update software and return receiver to factory settings 5 4 1 Timer Setting up Timer make possible to switch receiver to channels automatically according to schedule Number To select timer number use buttons lt gt Status By default set to Disabled Set to Enabled in order to get access to other options of timer Action You can select one of the following actions m Power On receiver will be turned ON at defined date and time on selected channel m Interval receiver will be turned ON at defined date and time on selected channel At the end of interval the receiver will be turned to stand by mode m Power Off receiver will be turned OFF at defined date and time Cycle You can setup repeating cycle of the timer action The receiver will execute action once daily or weekly Date or Week day Press OK button to display calendar or list of week days In calendar use A V lt P buttons to select date P P to change month Press OK to confirm selection If timer cycle set to Everyday the date selection is not active If timer cycle set to Weekly you can select week day Time use buttons 0 9 to enter time in Hours Minutes format Duration use buttons 0 9 to enter interval betwe
26. t ratio then your TV set then receiver will convert video in such a way that complete video picture fits to screen In Pan Scan mode geometrical proportions of picture would not be changed however part of video will be truncated SCART mode allows you to select between RGB and Composite video output It is recommended to use RGB mode because it gives better guality of picture 5 3 3 Time Setting To select language use buttons lt P or press OK to display list of available options and select language by A Wbuttons Press GREEN Save to store changes or EXIT to cancel Offset select time offset from Greenwich Meridian Time Value Auto reguire support from broadcaster side In this mode Time offset sets automatically and Summer MWinter time managed automatically Summer Time set ON during summer time day light save period or OFF during winter time For your information current date and time are displayed on the bottom of screen 5 3 4 OSD Display To select language use buttons lt P or press OK to display list of available options and select language by A Wbuttons Press GREEN Save to store changes or EXIT to cancel Banner Show set to ON if you wish to display information banner when zapping between channels or OFF if you do not want to see banner on channel zapping Banner time out set duration of zapping banner display on screen Transparency set level of menu transparency 14 www strong tv PART 1 o Engli
27. t your receiver with your TV set using a SCART cable 5 S PDIF To connect your receiver to digital audio amplifier 6 VIDEO This connector has a constant video signal for connection to TV set without SCART connector or to VCR 7 AUDIO These connectors give you the possibility to connect the audio signal to an external amplifier or to the audio input of your TV 8 Main power switch Power OFF and ON your receiver 9 Power cord Your receiver requires a voltage of 100 240 V AC Auto selectable 50 60 Hz 5 96 Make sure to check the power specification before connecting your receiver to the wall outlet A Warning Make sure all connections are made in correct order before connecting your receiver to the mains power Always at first power on your receiver then TV set www strong tv 5 lt S7RONG PART 1 English DIGITAL TV 2 3 Remote control 1 MUTE Mutes audio outputs of the receiver 2 POWER Turns receiver On Stand by 3 V V Increase decrease volume level 4 AV toggles SCART output between TV and AV modes 5 AUDIO Shows list of available audio languages for the channel you are watching In addition it sets the current channel audio to stereo left mono or right mono 6 P P For zapping to next previous channel in live view mode and for Page up and down in menu lists 7 MENU Displays Main menu of the receiver 8 INFO Displays information about current channel 9 EXIT Exits from the
28. tput TV SCART with support of RGB and Composite video 3 RCA Video Audio Left Audio Right USB S PDIF optical power switch 1 Subject of local broadcast conditions www strong tv 3 A 720NG PART 1 s English DIGITAL TV Package content m 1x Receiver m 1x User manual m Ix Remote control m 2x batteries AAA type Tips The batteries should not be recharged disassembled electrically short circuited or be mixed or used with other types of batteries 2 0 YOUR RECEIVER 2 1 Front panel 2 SSIR ONG U Digital Terrestrial Receiver O 75010 p gr Qs us 5 1 4 3 1 STANDBY Switch your receiver ON and OFF 2 INFO Displays information banner program details 3 CHAY For channel zapping in live view mode navigation up and down in menu mode 4 Mode indicator Red color indicates stand by mode green color indicates active mode 4 www strong tv PART 1 s English STRONG DIGITAL TV 2 2 Rear panel 6 7 8 9 96 0Oe VIDEO L AUDIO R ON am OFF I opos ccs m 8 Fahir in jlo TV Supplied by STRONG CE Japan 1 2 3 4 5 1 ANT IN To connect a terrestrial antenna for receiving broadcasting signal 2 TO TV To connect a TV set to receive analogue channels or to connect an extra receiver 3 USB To connect an external USB memory device 4 TV SCART To connec
Download Pdf Manuals
Related Search