MIDI Solutions F8
Contents
1. Connect the footswitches or any contact closures from tip to sleeve of a 1 4 phone jack to the F8 s footswitch inputs Fsw1 Fsw8 Connect the MIDI Out or Thru of the sending device to the MIDI In of the F8 The F8 draws power from the device that is connected to its MIDI input so even if the F8 does not need to receive MIDI messages from this device this connection is still required in order for the F8 to draw power the F8 s Echo parameter can be programmed to OFF to prevent any unwanted incoming MIDI messages from being echoed to the F8 s MIDI Out Connect the MIDI Out of the F8 to the MIDI In of the receiving MIDI device It is recommended that the number of MIDI Solutions products powered by a single MIDI Out or Thru be limited to four PROGRAMMING The F8 is programmed by sending it MIDI System Exclusive programming commands from a computer with a MIDI interface These commands are described on the MIDI Solutions website however the Programming Tools software creates these commands automatically see www midisolutions com support htm Upon receipt of a programming command the F8 s MIDI indicator LED flashes rapidly for about one second to indicate that the setting has been stored Ensure that the LED completes its flashing after receiving a programming command before sending another programming command the Programming Tools software automatically inserts these delays Settings are retained after power is removed and the unit ca2. where FO F7 is the System Exclusive message the F8 is being programmed to send max 20 byes All bytes must be in Hexadecimal format see hexadecimal conversion table at end ii Footswitch Input 00 for Fsw1 07 for Fsw8 To program the F8 to send out a System Exclusive message when a footswitch is released send it the following System Exclusive Programming commands gt FO 00 00 50 24 06 ii 00 F7 followed by FO F7 where FO F7 is the System Exclusive message the F8 is being programmed to send max 20 byes All bytes must be in Hexadecimal format see hexadecimal conversion table at end ii Footswitch Input 00 for Fsw1 07 for Fsw8 Example To program the F8 to send out the MIDI Machine Control Play command FO 7F 7F 06 02 F7 when Fsw4 is depressed and the MIDI Machine Control Stop command FO 7F 7F 06 01 F7 when Fswd is released send the F8 the following System Exclusive Programming commands FO 00 00 50 24 06 03 01 F7 followed by FO 7F 7F 06 02 F7 FO 00 00 50 24 06 03 00 F7 followed by FO 7F 7F 06 01 F7 NOTE ON FILTER To program the F8 to filter Note On messages on a selected MIDI channel when a footswitch is depressed send it the following System Exclusive programming command gt FO 00 00 50 24 OC ii cc aa F7 ii Footswitch Input 00 for Fsw1 07 for Fsw8 cc MIDI channel see MIDI channel table at end aa 01 Send All Notes Off on depression of footswitch aa 00 do not send All Notes Off on
3. Note Off if aa 01 or Control Change of value zero if aa 02 is sent on release of the footswitch To program the F8 to operate in Tap Tempo mode and also respond to a Note or Control Change message of value gt 0 as a tap send it the following System Exclusive programming command gt F0 00 00 50 24 OB ii aa nn cc F7 All bytes must be in Hexadecimal format see hexadecimal conversion table at end ii Footswitch Input 00 for Fsw1 07 for Fsw8 aa 11 for Note 12 for Control Change nn Note number if aa 11 Control Change number if aa 12 cc MIDI channel of incoming Note or Control Change message see MIDI channel table at end To program the F8 to operate in Tap Tempo mode and also to respond to a Note to specify the exact tempo in bpm send it the following System Exclusive programming command gt FO 00 00 50 24 OB ii 21 bb cc F7 All bytes must be in Hexadecimal format see hexadecimal conversion table at end ii Footswitch Input 00 for Fsw1 07 for Fsw8 bb offset added to Note number to obtain tempo cc MIDI channel of incoming Note message see MIDI channel table at end To program the F8 to operate in Tap Tempo mode and also to respond to a Control Change message to specify the exact tempo in bpm send it the following System Exclusive programming command gt FO 00 00 50 24 OB ii 22 nn bb cc F7 All bytes must be in Hexadecimal format see hexadecimal conversion table at end ii Footswitch Input 00 f
4. 1 47 Sound Controller 2 default Timbre Harmonic Content 72 48 Sound Controller 3 default Release Time 73 49 Sound Controller 4 default Attack Time 74 4A Sound Controller 5 default Brightness 75 79 4B 4F Sound Controllers 6 10 no defaults 80 83 50 53 General Purpose Controllers s 5 8 84 54 Portamento Control 85 90 55 5A Undefined 91 5B Effects 1 Depth formerly External Effects Depth 92 5C Effects 2 Depth formerly Tremolo Depth 93 5D Effects 3 Depth formerly Chorus Depth 94 5E Effects 4 Depth formerly Celeste Detune Depth 95 5F Effects 5 Depth formerly Phaser Depth 96 97 60 61 Data increment Data decrement 98 99 62 63 Non Registered Parameter Number LSB MSB 100 101 64 65 Registered Parameter Number LSB MSB 102 119 66 77 Undefined 120 127 78 7F Reserved for Channel Mode Messages HEXADECIMAL CONVERSION TABLE WARRANTY MIDI Solutions Inc warrants this product to be free from defects in material and workmanship for a period of one 1 year from date of purchase This warranty is void if the product has been damaged by accident misuse alteration unauthorized repairs or other causes not arising out of defects in material or workmanship Under no circumstances will MIDI Solutions be liable for any loss of profits benefits time interrupted operation commercial loss or consequential damages arising out of the use or inability to use the product MIDI Solutions specifically disclaims any implied war
5. E FOOTSWITCH CLOSURE To cause the F8 to simulate the action of any footswitch without physically depressing or releasing the footswitch send it the following following System Exclusive message gt FO 00 00 50 24 10 ii aa F7 all values in Hexadecimal ii Footswitch input 00 for Fsw1 through to 07 for Fsw8 aa 00 Simulate RELEASE aa 01 Simulate DEPRESSION Example To cause the F8 to simulate the release operation of Fsw5 send it the following System Exclusive message FO 00 00 50 24 10 04 00 F7 13 MIDI CHANNEL TABLE The value cc in the programming commands is assigned according to the following table mocme e s e 7 8 s w ne ew s AL ee 00 01 02 os os o o o7 o 09 oa os oc op o oF 7F MIDI CONTROL CHANGE TABLE Decimal Hexadecimal Control Function 0 00 Bank Select 1 01 Modulation wheel or lever 2 02 Breath Controller 3 03 Undefined 4 04 Foot controller 5 05 Portamento time 6 06 Data entry MSB 7 07 Channel Volume 8 08 Balance 9 09 Undefined 10 OA Pan 11 0B Expression Controller 12 13 0C 0D Effect Controls 1 2 14 15 0E 0F Undefined 16 19 10 13 General Purpose Controllers s 1 4 20 31 14 1F Undefined 32 63 20 3F LSB values for 0 31 64 40 Damper pedal sustain 65 41 Portamento On Off 66 42 Sostenuto 67 43 Soft pedal 68 44 Legato Fsw vv 00 3F Normal 40 7F Legato 69 45 Hold 2 70 46 Sound Controller 1 default Sound Variation 7
6. MIDI Solutions PROFESSIONAL SERIES FS 8 INPUT MIDI FOOTSWITCH CONTROLLER OPERATING INSTRUCTIONS MIDI Solutions F8 Operating Instructions M424 100 2012 MIDI Solutions Inc All rights reserved MIDI Solutions Inc PO Box 3010 Vancouver BC Canada V6B 3X5 www midisolutions com INTRODUCTION Thank you for purchasing the MIDI Solutions F8 8 input MIDI Footswitch Controller The MIDI Solutions F8 can be programmed to generate a variety of MIDI messages in response to contact closures between the tip and sleeve of its eight 1 4 phone jack inputs It is also possible to program the footswitch inputs to perform a variety of other functions such as Rechannelize Transpose and Tap Tempo All programmed settings are retained even after power is removed from the unit The MIDI Solutions F8 is MIDI powered and requires no batteries or power supply to operate In Power Le om wu MIDI Out or Thru Sending Device MIDI In Receiving Device _ or contact closure el or contact closure or contact closure u or contact closure T or contact closure rer or contact closure _ or contact closure re or contact closure CONNECTIONS To program the F8 connect the MIDI Out from your MIDI interface to the MIDI In of the F8 The MIDI Out and footswitch inputs can be left disconnected during programming Once the F8 has been programmed it can be inserted wherever it is required in your MIDI setup
7. Program Change 0 on all MIDI channels when Fsw2 is depressed and nothing when the footswitch is released set ii 01 Fsw2 pp 00 Program Change 0 cc 7F 7F specifies all MIDI channels omit qq nothing sent on release bb bb 03 06 Bank Select MSB 3 Bank Select LSB 6 and omit dd dd nothing sent on release This results in the following System Exclusive programming command FO 00 00 50 24 04 01 00 7F 03 06 F7 PROGRAM CHANGE CAPTURE To program the F8 to capture the Program Change and Bank Select messages it receives while a footswitch is depressed send it the following System Exclusive programming command gt F0 00 00 50 24 OD ii F7 ii Footswitch Input 00 for Fsw1 07 for Fsw8 Once the Program Change and Bank Select data has been captured tapping the footswitch causes the F8 to resend the captured data Captured data is retained even after power is removed from the F8 PROGRAM CHANGE INC DEC Any two inputs of the F8 may be programmed to provide an increment decrement Program Change function The inputs are programmed as follows gt INC input FO 00 00 50 24 07 ii 01 cc xx yy F7 xx yy is optional gt DEC input FO 00 00 50 24 07 ii 00 cc xx yy F7 xx yy is optional All bytes must be in Hexadecimal format see hexadecimal conversion table at end ii Footswitch Input 00 for Fsw1 07 for Fsw8 cc MIDI channel see MIDI channel table at end xx yy is optional xx minimum value yy maximum v
8. alue Example To program the F8 to increment the Program number on MIDI channel 16 when Fsw5 is depressed and decrement it when Fsw6 is depressed send the F8 to following System Exclusive programming commands FO 00 00 50 24 07 04 01 OF F7 FO 00 00 50 24 07 05 00 OF F7 PROGRAM CHANGE ENTER AND SELECT To program the F8 to allow a keyboard to be used as a numeric keypad to enter program numbers or notes from a keyboard to select specific programs numbers send the F8 the following System Exclusive programming command gt FO 00 00 50 24 14 ii mm cc F7 All bytes must be in Hexadecimal format see hexadecimal conversion table at end ii Footswitch Input 00 for Fsw1 07 for Fsw8 mm specifies the mode of operation as follows 00 Keyboard is used as a numeric keypad to enter the program number 0 127 while footswitch is depressed with middle C representing 0 to A above middle C representing 9 gt 0 Keyboard is used to select a specific program number 0 127 while footswitch is depressed starting from note mm for program 0 Pressing the note twice adds 64 to the program value the Program Change message is sent on release of the footswitch cc MIDI channel see MIDI channel table at end 10 SYSTEM EXCLUSIVE To program the F8 to send out a System Exclusive message when a footswitch is depressed send it the following System Exclusive Programming commands gt FO 00 00 50 24 06 ii 01 F7 followed by FO F7
9. ble at end tt Debounce time in ms 00 is optional if included the above debounce time tt is doubled The clear settings command resets the debounce time to 50 ms Examples To program the F8 to echo incoming MIDI messages to the MIDI output and send nothing on power up send it the following System Exclusive programming command FO 00 00 50 24 00 01 01 F7 To program the toggle parameter of Fsw8 to ON and force the polarity to NORMALLY OPEN send the F8 the following System Exclusive programming command FO 00 00 50 24 00 02 07 01 00 00 F7 To program the footswitch debounce time to 100 ms send the F8 the following System Exclusive programming command FO 00 00 50 24 00 03 64 F7 INDIVIDUAL FOOTSWITCH FUNCTIONS Each footswitch input of the F8 can be programmed with one of the functions on the following pages NOTE ON To program the F8 to send out up to eight Note On messages when a footswitch is depressed send it the following System Exclusive programming command gt FO 00 00 50 24 aa ii tt nn vv cc nn vv F7 tt and nn wv are optional All bytes must be in Hexadecimal format see hexadecimal conversion table at end aa specifies mode of transmission as follows 01 Send Note On s on depression of footswitch Note Off s on release 11 Send Note On s on depression of footswitch nothing on release 21 Send Note On s on depression of footswitch Note Off s after the duration specified by tt see below 31 Send Note On s on depr
10. depression To start filtering Note On messages depress the footswitch the All Notes Off message is sent out at this time to stop filtering release the footswitch RECHANNELIZE To program the F8 to rechannelize an incoming MIDI channel to a selected outgoing MIDI channel when a footswitch is depressed send it the following System Exclusive Programming command gt FO 00 00 50 24 09 ii 10 cc pp 00 F7 10 pp and 00 are optional All bytes must be in Hexadecimal format see hexadecimal conversion table at end ii Footswitch Input 00 for Fsw1 07 for Fsw8 10 is optional if included then the 16 notes from middle C up are used to select the channel If omitted then the number of notes played while the footswitch is depressed is used to select the channel cc Incoming MIDI channel to rechannelize see MIDI channel table at end pp is optional specifies preset outgoing MIDI channel see MIDI channel table at end 00 is optional if included then incoming notes are ignored while footswitch is depressed To rechannelize an incoming MIDI channel depress the footswitch the All Notes Off message is sent out at this time select the channel by playing notes on the keyboard these notes are not echoed to MIDI Out and release the footswitch If no notes are received by the F8 during this period the outgoing MIDI channel is set to the preset pp To program the F8 to ignore incoming notes and change directly to the preset MIDI channel pp w
11. depression of footswitch nothing on release ii 04 Fsw5 nn 07 volume is CC 7 vv 7F 7F is the hexadecimal value for 127 the maximum value and cc 7F 7F specifies all MIDI channels These values result in the following System Exclusive programming command FO 00 00 50 24 12 04 07 7F 7F F7 START STOP To program the F8 to send MIDI Start and Stop messages send it the following System Exclusive programming command gt F000 00 50 24 05 ii ss F7 ss is optional ii Footswitch Input 00 for Fsw1 07 for Fsw8 ss specifies the mode of transmission as follows 00 Send Stop on depression of footswitch nothing on release 01 Send Start on depression of footswitch nothing on release ss omitted Send Start on depression of footswitch Stop on release Note that the F8 can be programmed to toggle between Start and Stop each time the footswitch is depressed by setting the Footswitch Toggle parameter to Toggle ON see Device Parameters PITCH BEND To program the F8 to send out a Pitch Bend message when a footswitch is depressed send it the following System Exclusive programming command gt F000 00 50 24 aa ii Il mm cc F7 All bytes must be in Hexadecimal format see hexadecimal conversion table at end aa specifies the mode of transmission as follows 03 Send II mm value on depression of footswitch reset pitch to zero on release 13 Send II mm value on depression of footswitch nothing on release ii Footswitch In
12. ession of footswitch Note Off s when the footswitch is released after the minimum duration tt see below 41 Send Note On s on depression of footswitch Note Off s when the footswitch is released up to the maximum duration tt see below 51 Cycle through each Note On on depression of footswitch send the corresponding Note Off on release 61 Cycle through each Note On on depression of footswitch send nothing on release ii Footswitch Input 00 for Fsw1 07 for Fsw8 tt Duration in 8 ms increments or 1 s increments if preceded by 00 ttis only included if aa 21 31 or 41 nn Note number vv Note On velocity cc MIDI channel see MIDI channel table at end nn vv Additional notes and velocities up to eight notes total Example To program the F8 to send out a middle C of velocity of 64 on MIDI channel 5 when Fsw 6 is depressed and send the corresponding Note Off after 7 seconds set aa 21 Send Note On on depression of footswitch Note Off after the duration specified by tt ii 05 Fsw6 tt 00 07 insert 00 prior to 07 to specify 1s increments nn 3C middle C is Note number 60 3C is the hexadecimal value for 60 vv 40 40 is the hexadecimal value for 64 and cc 04 04 specifies MIDI channel 5 These values result in the following System Exclusive programming command FO 00 00 50 24 21 05 00 07 3C 40 04 F7 CONTROL CHANGE To program the F8 to send out up to eight Control Change CC messages when a footswi
13. hen the footswitch is depressed insert 00 in the above command as shown Example Setting To program the F8 to accept rechannelize selection for incoming MIDI channel 1 when Fsw1 is depressed send it the following System Exclusive programming command FO 00 00 50 24 09 00 00 F7 Example Operation with Above Setting To rechannelize from MIDI channel 1 to MIDI channel 2 depress Fsw1 play any two notes and release the footswitch All MIDI channel 1 messages will now be rechannelized to MIDI channel 2 Continuing to tap the footswitch will cause the F8 to toggle between the original and selected channels TRANSPOSE To program the F8 to transpose incoming note messages by a selected interval by depressing a footswitch send it the following System Exclusive Programming command gt FO 00 00 50 24 OA ii cc pp 00 F7 pp and 00 are optional All bytes must be in Hexadecimal format see hexadecimal conversion table at end ii Footswitch Input 00 for Fsw1 07 for Fsw8 cc Incoming MIDI channel to transpose see MIDI channel table at end pp is optional specifies preset transpose interval 40 zero transpose 00 is optional if included then incoming notes are ignored while footswitch is depressed To specify a transpose interval depress the footswitch the All Notes Off message is sent out at this time play the note above or below middle C corresponding to the transpose interval this note is not echoed to MIDI Out and release
14. n then be inserted wherever it is required in your MIDI setup OPERATION Ensure that the footswitches are connected to the F8 before it is powered up as their polarities are stored at this time if auto polarity is selected The F8 s MIDI Indicator LED will light as soon as the sending device is turned on and flashes whenever MIDI data passes through the unit Depressing the footswitches causes the F8 to perform its programmed functions PROGRAMMING COMMANDS CLEAR SETTINGS To clear all of the F8 s settings send it the following System Exclusive programming command gt FO 00 00 50 24 00 00 F7 all values in Hexadecimal It is recommended to send the Clear Settings command to the F8 prior to programming the unit to ensure that all previous settings are cleared DEVICE PARAMETERS The following Device Parameters are in effect regardless of the functions that each of the footswitch inputs have been programmed to perform Echo When Echo is ON all incoming MIDI messages received by the F8 are echoed to its MIDI output When Echo is OFF only the messages generated by the F8 are sent to its MIDI output Send State on Power up The F8 can be programmed to send the state of all footswitch inputs on power up Toggle When the Toggle parameter is OFF for a particular footswitch the footswitch performs the depress operation when it is depressed and the release operation when it is released When Toggle is ON the footswitch toggles bet
15. or Fsw1 07 for Fsw8 nn Control Change number bb offset added to Control Change value to obtain tempo cc MIDI channel of incoming Control Change message see MIDI channel table at end SONG SELECT To program the F8 to send out a Song Select message when a footswitch is depressed send it the following System Exclusive programming command gt FO 00 00 50 24 OE ii ss tt F7 all values in Hexadecimal ii Footswitch input 00 for Fsw1 through to 07 for Fsw8 ss Song Select sent on depression of footswitch tt is optional specifies Song Select sent on release of footswitch Example To program the F8 to send out Song Select 5 when Fsw1 is depressed send it the following System Exclusive programming command FO 00 00 50 24 OE 00 04 F7 SONG SELECT INC DEC Any two inputs of the F8 may be programmed to provide an increment decrement Song Select function The inputs are programmed as follows gt INC input FO 00 00 50 24 OF ii 01 xx yy F7 all values in Hex gt DEC input FO 00 00 50 24 OF ii 00 xx yy F7 all values in Hex xx yy is optional xx minimum value yy maximum value ii Footswitch input 00 for Fsw1 through to 07 for Fsw8 Example To program the F8 to increment the Song Select number when Fsw8 is depressed and decrement the Song Select number when Fsw7 is depressed send the F8 the following System Exclusive programming commands FO 00 00 50 24 OF 07 01 F7 FO 00 00 50 24 OF 06 00 F7 SIMULAT
16. put 00 for Fsw1 07 for Fsw8 Il LSB pitch value mm MSB pitch value cc MIDI channel see MIDI channel table at end Example To program the F8 to send out a pitch bend message of 1 semitone to a device that is set to a full octave pitch bend range on channel 12 when Fsw1 is depressed set aa 03 send value on depression reset pitch to zero on release ii 00 Fsw1 Il mm 2B 45 2B 45 is the value for 1 semitone bend in a full octave range and cc 0B 0B specifies MIDI channel 12 These values result in the following System Exclusive programming command FO 00 00 50 24 03 00 2B 45 0B F7 PROGRAM CHANGE To program the F8 to send out a Program Change message when a footswitch is depressed send it the following System Exclusive programming command gt FO 00 00 50 24 04 ii pp cc qq bb bb dd dd F7 qq bb bb and dd dd are optional All bytes must be in Hexadecimal format see hexadecimal conversion table at end ii Footswitch Input 00 for Fsw1 07 for Fsw8 pp Program number sent on depression of footswitch cc MIDI channel see MIDI channel table at end qq is optional specifies Program number sent on release of footswitch bb bb is optional specifies Bank Select MSB and LSB values to precede pp on depression of footswitch dd dd is optional specifies Bank Select MSB and LSB values to precede qq on release of footswitch Example To program the F8 to send out Bank Select MSB 3 Bank Select LSB 6
17. ranties of merchantability and fitness for a particular purpose If the product requires service a Return Merchandise Authorization RMA number must be obtained from MIDI Solutions and the product must be shipped prepaid to a specified Service Center MIDI Solutions will repair or replace the product at our discretion and will pay return shipping fees The customer is responsible for any damage or loss sustained during shipment in any direction 15
18. tch is depressed send it the following System Exclusive programming command gt FO 00 00 50 24 aa ii tt nn vv cc nn vv F7 tt and nn wv are optional All bytes must be in Hexadecimal format see hexadecimal conversion table at end aa specifies mode of transmission as follows 02 Send CC s 12 Send CC s on depression of footswitch nothing on release 22 Send CC s on depression of footswitch CC s of value 0 after the duration specified by tt see below 32 Send CC s on depression of footswitch CC s of value 0 when the footswitch is released after the on depression of footswitch CC s of value 0 on release minimum duration tt see below 42 Send CC s on depression of footswitch CC s of value 0 when the footswitch is released up to the maximum duration tt see below 52 Cycle through each CC on depression of footswitch send the corresponding CC of value 0 on release 62 Cycle through each CC on depression of footswitch send nothing on release ii Footswitch Input 00 for Fsw1 07 for Fsw8 tt Duration in 8 ms increments or 1 s increments if preceded by 00 ttis only included if aa 22 32 or 42 nn Control Change number vv Control Change value sent on depression of footswitch cc MIDI channel see MIDI channel table at end nn vv Additional CC numbers and values up to eight CCs total Example To program the F8 to send maximum volume on all MIDI channels when Fsw5 is depressed set aa 12 Send CC on
19. the footswitch If no notes are received by the F8 during this period the transpose interval is set to the preset transpose interval pp To program the F8 to ignore incoming notes and change directly to the preset transpose interval pp when the footswitch is depressed insert a 00 after the pp in the above programming command 11 12 TAP TEMPO To program the F8 to operate in Tap Tempo mode sending MIDI timing clocks at a tempo corresponding to the taps of one of its footswitch inputs send it the following System Exclusive programming command gt FO 00 00 50 24 OB ii F7 All bytes must be in Hexadecimal format see hexadecimal conversion table at end ii Footswitch Input 00 for Fsw1 07 for Fsw8 To program the F8 to operate in Tap Tempo mode and also send a Note or Control Change message along with each tap of the footswitch send it the following System Exclusive programming command gt FO 00 00 50 24 OB ii aa nn vv cc 00 F7 00 is optional All bytes must be in Hexadecimal format see hexadecimal conversion table at end ii Footswitch Input 00 for Fsw1 07 for Fsw8 aa 01 to send Note 02 to send Control Change nn Note number if aa 01 Control Change number if aa 02 vv Note velocity if aa 01 Control Change value if aa 02 cc MIDI channel of outgoing Note or Control Change message see MIDI channel table at end 00 is optional If inserted nothing is sent on release of the footswitch If not inserted then a
20. ween the depress operation and the release operation each time the footswitch is depressed nothing is done on release of the footswitch Footswitch Polarity When Auto Polarity is ON for a footswitch the F8 determines the polarity of the footswitch based on its power up state When Auto Polarity is OFF the polarity is forced according to the Polarity settings Wait for Next Bar The F8 can wait until the beginning of the next bar to perform the footswitch action Debounce Time The Debounce Time specifies the length of time after a footswitch changes state before a new change of state is allowed to occur To program these parameters send the F8 the following System Exclusive programming commands gt F000 00 50 24 00 01 aa bb F7 bb is optional ii Footswitch Input 00 for Fsw1 07 for Fsw8 aa 00 Echo OFF aa 01 Echo ON bb is optional If bb 01 the F8 will send the state of each footswitch on power up gt FO 00 00 50 24 00 02 ii bb cc dd ee F7 ee is optional ii Footswitch Input 00 for Fsw1 07 for Fsw8 bb 00 Toggle OFF bb 01 Toggle ON cc 00 Auto Polarity OFF cc 01 Auto Polarity ON dd 00 Normally OPEN polarity dd 01 Normally CLOSED polarity dd is ignored if cc 01 ee is optional If ee 7F the F8 waits for the beginning of the next bar to perform the footswitch action gt FO 00 00 50 24 00 03 00 tt F7 00 is optional All bytes must be in Hexadecimal format see hexadecimal conversion ta
Download Pdf Manuals
Related Search