the User Manual here.
Contents
1. 0S8XC XScV OSOXCLEXSCV O SXCLEXSCY 13ubreu u1dep u1piM S AO1S 06 0 06 0 06 0 06 0 GU ease Dun eoH 1951 99 G8 991 0 G9 991 0 991 0 12 Rais O Tee Q Tee Wall Hung Q Tee Insert MA 1nd1no jeUIWON Specifications Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Installation Instructions The following pages give instructions for the safe and proper installation of this heatino appliance in the UK These instructions cover the basic principles of installation although detail may need slight modification to suit particular local site conditions In all cases the Installation must comply with current UK Building Regulations Local Authority Byelaws and other specifications or regulations as they affect the installation of the stove Please note that it is a legal requirement under England and Wales Building Regulations that the installation of the stove is either carried out under Local Authority Building Control approval or 15 installed by a Competent Person registered with a Government approved Competent Persons Scheme HETAS Ltd operate such a Scheme and a listing of their Reg istered Competent Persons can be found on their website at www hetas co uk It should be noted that the current Building Regulations requirements are given in Ap proved Document J These requirements may also be met by adopting the relevant recom mendations given in British Standards BS 8303 and BS EN2. ART WE OF FIRE INSTRUCTIONS FOR INSTALLATION USE AND MAINTENANCE RAIS Q TEE RAIS Q TEE WALL RAIS Q TEE INSERT IMPORTANT INFORMATION On first lighting the stove you must be careful not to touch the painted surfaces and it is MOST IMPORTANT that the door is kept slightly ajar in order for the door seal and sealant to cure This will prevent the door seal sticking to the painted body and becoming damaged Rais Q Tee Q Tee Wall Hung amp Q Tee Insert The oven is wrapped in packaging that is recyclable This must be disposed of according to national rules regarding the disposal of waste The glass can not be reused The glass should be discarded along with the residual waste from ceramics and porcelain Pyrex glass has a higher melting temperatur and therefore can not be reused We cannot be held responsible for any misprints Rais Q Tee Q Tee Wall Hung amp Q Tee Insert IWHIOIEBO Ini OO Iau EIS BOESCH INLD agp LON PRI Io ee pep oji DEA Mj gr PPT Ai appen muy paja kapas a pu maint PEAT reg c BE WW THI An enl prp and y get ura ae uv SVAN NAVIES Tt sil eum set eas Jam Llu KEE peu puy uama juges pe eiut UF yg au si Dwg mana og
3. Then remove the smoke chicane by pushing it backwards tipping it up On one side and turn slithtly tilted Caretully lift out the smoke chicane Remove dirt and dust and mount the parts in reverse order 38 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Problem Solving Smoke spillage around door Could be due to too low draught in the chimney lt 12Pa Check whether the flue or chimney is blocked check whether the extraction hood is switched on if it is switch it off and open a win dow door in the proximity of the stove for a short while Soot on glass Could be because the firewood is too wet make sure that the stove is heated properly when firing up prior to closing the door Could be because the damper regulation is too low A stove burning too strong could be caused by leak around the door seal chimney draught too large gt 22 Pa draught control regulator should be installed A stove burning too weakly could be caused by too little firewood too little air supply for room ventilation unclean smoke channels leaky chimney leakage between chimney and If your stove continues to malfunction we recommend that you contact your RAIS dis tributor or chimney sweep IMPORTANT To ensure sate burning there must be clear yellow flames or clear embers at all times The firewood should not be smouldering Therefore you should never completely cut off the air supply WARNING I In
4. Q un AE 28 o SE ab 9 C AS o YA O E Distance to non combustible plate min 800 mm nstallation height min 400 mm N Distance to Min 50 mm furniture Distance to non Min convection area 350 cm be min 650 mm combustible 0 mm low the stove may be distributed 10 mm is recommended Min 300 mm 30 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert For the Installer Finally before firing the stove for the first time a check should be made to ensure that the assembly and stove installation has been satisfactory and that there are no leaks in any seals in the appliance and appliance connections to the chimney Ensure that the appliance and chimney are functioning correctly before finally hand ing over to the user If necessary read the later parts of this manual for guidance on care required when first lighting Inform the user that the appliance has been commissioned and ready to use and give instruction on the safe operation of the stove These Instructions must be left with the user and the user should be instructed to keep them in a safe place Operating instructions Please note that HETAS Ltd Appliance Approval only covers the use of dry seasoned wood logs on this appliance HETAS Ltd Approval does not cover the use of other fuels either alone or mixed with the wood logs nor does it cover Instructions for the use of other fuels Fuel
5. The outlet from the chimney should be above the roof of the building in accordance with the provisions of Building Regulations Approved Document J If installation is into an existing chimney then it must be sound and have no cracks or other faults which might allow fumes into the house Older properties especially may have chimney faults or the cross section may be too large i e more than 230 mm x 230 mm Remedial action should be taken if required seeking expert advice if necessary If it is found necessary to line the chimney then a flue liner suitable for solid fuel must be used in accordance with Building Regulations Approved Document J Any existing chimney must be clear of obstruction and have been swept clean immedi ately before installation of the stove If the stove is fitted in place of an open fire then the chimney should be swept one month after installation to clear any soot falls which may have occurred due to the difference in combustion between the stove and the open fire If there is no existing chimney then either a prefabricated block chimney in accordance with Building Regulations Approved Document J or a twin walled insulated stainless steel flue to BS 4543 can be used These chimneys must be fitted in accordance with the manu facturer s instructions and Building Regulations 14 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert A single wall metal fluepipe is suitable for connecting the stove to the chimney but is not
6. When the last flames are extinguished and there is a nice layer of embers 6 add 2 3 pieces of wood Close the door and once the fire has a good hold closed door completely Damper see adjustment of air damper After approx 5 min or when the flames are clear and stable 7 close the damper gradually Note Keep an eye on the stove when lighting During operation the door should always remain shut 35 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Cleaning and care Glass Most woodstoves use a ceramic glass product which Is resistant to heat but requires clean ing to keep its appearance Soot or opaque marks can easily cleaned if the marks are fresh however If you leave the glass dirty for any length of time the acid from the wood can etch the surface of the glass permantley wet unseasoned wood soft wood such as used in the building industry pallet wood should be avoided Only clean when cold Use only stove glass cleaners to re move heavy tar soot deposits All other marks can normally be removed with a damp cloth then dry with a clean cloth or newspaper do not let the glass dry before applying a dry clean cloth With more stubborn marks i e Opaque areas frosting you need put a small amount of wood ash on a clean damp cloth If the opaque mark frosting doesn t come out contact your dealer for a special remover Paint finish The appliance has been coated with a high temperature paint which ca
7. about design and quality in your home To make the most of your wood burning stove it is important that you read the manual thoroughly before installing and using it In the case of warranty coverage and for general queries regarding your wood burning stove it is important that you know the stove s production number We therefore recom mend that you note down the number in the table below The production number is located on the back of the stove at the bottom Warranty Your RAIS wood burning stove comes with a 5 year warranty The warranty however does not cover heat insulating materials glass and seals Any alterations made to the stove will void the warranty Produced by RAIS A S Industrivej 20 9900 Frederikshavn Danmark Prod nf SJnOU u yey pun og p nous Huljjanjoy uoneJedo 95205 UO Do seb e ouus S O seb a OWS gUl N DUJ uiq 0 paunseauu 15 65 6 6S0 8S0 SN 01 228 sepinaeg 96 76 96 76 79 78 19 6 1oopsse 6 1oop 1s 1uBI AA 8 w leased 1ubneup vu oyeudn vin GZ XOJdde JO poom SL GI GI NI Jo 5 e z uo 5 67 UaYM POOM JO 1unouJe pepusuJlulO29MH O ZXOLZXLLE OLZXOLZXZLE OZZXOLZXZLE OLZXOLTZXZLE uu 1uBl u U1d p u1piA sogueu gt 9
8. amp HEF E di DEE 9 SISI LE ALD SIV Tiir sO a l E W SIM Rais Q Tee Q Tee Wall Hung amp Q Tee Insert These instructions together with those in the instruction booklet cover the basic principles to ensure the satisfactory installation of the stove although detail may need slight modification to suit particular local site conditions In all cases the installation must comply with current Building Regulations Local Authority Byelaws and other specifications or regulations as they affect the installation of the stove It should be noted that the Building Regulations requirements may be met by adopting the relevant recommendations given in British Standards BS 8303 BS EN 15287 1 2007 as an alternative means to achieve an equivalent level of performance to that obtained following the guidance given in Approved Document J Please note that it is a legal requirement under England and Wales Building Regulations that the installation of the stove is either carried out under Local Authority Building Control approval or is installed by a Competent Person registered with a Government approved Competent Persons Scheme HETAS Ltd operate such a Scheme and a listing of their Registered Competent Persons can be found on their website at www hetas co uk CO Alarms Building regulations reguire that when ever a new or replacement fixed solid fuel or wood biomass appliance is installed in a dwelling a carbon monoxide
9. 15287 1 WARNING Health and Safety Advice Notice The installation of this heating appliance is governed by the Health and Safety at Work Act 1974 It is the responsibility of the installer to ensure that all requirements of this Act are met during the installation works Attention is drawn in particular to the following Handling The appliance is a heavy item and adequate facilities must be available for loading unloading and site handling Fire Cement Some types of fire cement are caustic and should not be allowed to come into con tact with the skin Protective gloves should be worn when handling fire cement In case of contact with the skin wash immediately with plenty of water Asbestos This stove contains no asbestos If there is a possibility of disturbing any asbestos in the course of installation then please seek specialist guidance and use appropriate protective equipment Metal Parts When installing or servicing this stove care should be taken to avoid the possibility of personal injury Important Warning Preparatory Work and Safety Checks This stove must not be installed into a chimney that serves any other heating appli ance It s recommendet not have an extractor fan fitted in the same room as the stove as this can cause the stove to emit fumes into the room _ f this appliance is installed into an existing chimney the chimney must first be swept and examined for soundness and suitability before the a
10. Socket 15 1 837650490 Wall bracket flue 16 1 836140190 Standard front cover 17 1 836010190 Mantle Q Tee insert 18 1 8364101 Reflectorplate back side 41 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Position 2 Position 3 Position 1 Using the wood burning stove Spare parts ir S Rais Q Tee Q Tee Wall Hung amp Q Tee Insert ART 22 OF FIRE Assembly instruction Mounting the air box on O Tee stove O Tee 57 amp O Tee 65 1 Tilt the stove and lay it on its back Remove the front panel below the door O Tee 57 and O Tee 65 Remove the reflector plate O Tee 57 2 Remove the 3 M6 screws one by one and replace it with 3 M6 stand offs Do not remove the air damper 3 If air is provided to the stove from the floor remove the knock out plate on the air box Mount the connection piece with the 3 M4 screws 4 If air is provided to the stove from the back side mount the 3 srews in the holes at the knock out plate of the air box 43 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert ART 22 OF FIRE 5 Place the air box as shown on picture and hand tighten the 3 screws Note that the air box is fixed by 2 pins at the back of the stove 6 Atthe front of the air box the small plate is placed as shown in picture Mount it with 2 M5 screws If needed adjust the plate for easier movement of the air damper handle 7 If air is provided to the stov
11. case of chimney fire shut off all air supply on the wood burning stove contact the fire department never attempt to put out fire with water afterwards you should ask your chimney sweeper to check the stove and chimney If the firewood is only burning slowly without flames or is smoking and too little air is added unburned exhaust gasses are developed Exhaust gasses can be ignited and explode leading to damage to material and possibly personal injury Never close the air supply completely when lighting a fire in the stove 39 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Accessories Q Tee 8351790 Air box 835040190 Socket 836142590 Special front cover 40 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Spare parts If spare parts other than those recommended by RAIS are used the warranty is voided All replaceable parts can be bought as spare parts from your RAIS distributor See the following spare parts diagrams for the individual products Spare parts drawing Q Tee front of the user manual Pos Ref Ouantity Part no Description 1 1 835010390 Mantle Q Tee 65 2 1 835010290 Mantle Q Tee 57 3 1 8352090 Steel door 4 1 8351090 Glass door 5 1 835050490 Cover Q Tee 65 6 1 835052490 Cover 57 7 1 8352200 Fire brick set 8 1 8353800 Shaking grate 9 1 8354001 Ash pan 10 1 61 00 Flue collar 6 11 1 61 105 Flue collar 5 12 1 8350990 Air damper 13 1 8355500 Seal set 14 1 835040190
12. ensure that all appliance and flue installations are undertaken by a competent approved installer following the Rais installation guide and are to current We recommend that all dimensions are checked against the appliance on site TYPICAL INSTALLATIONS local Building Regulations MARCH 2011 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Rais Q Tee Wall Hung 50 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert 51 ART am OF FIRE RAIS A S Industrivej 20 DK 9900 Frederikshavn www rais dk U K Distributor Robeys Ltd Riverside Goods Road Belper Derbyshire England DE56 1UU Tel 01773 820940 Fax 01773 820477 E Mail info robeys co uk THE ORIGINAL June 2012
13. min B in front floor 300 mm 300 mm to the side floor 150 mm 150 mm D to the rear wall 350 mm 275 mm E to the side of the wall 275 mm 225mm Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Corner setting 45 fixed socket Uninsulated flue Insulated A Distance to furniture min 650 mm 650 mm Distance to flammable materials min B in front floor 300 mm 300 mm C to the side floor 150 mm 150 mm D to the rear wall 225 mm 175 mm E to the side of the wall 275 225 Installation distance in case of non combustible Using non insulated smoke pipe the minimum distance to combustible wall must 225 mm from smoke pipe We recommend a minimum distance to non combustible material of 50 mm F for cleaning considerations It should always be possible to access the access door 20 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Placement of Q Tee Wall Installation distance in case of non combustible back wall and combustible side wall If the stove is to be installed above a wooden floor it must be covered with a non com bustible material at a thickness and seize which is in accordance with UK Building Regula tions Normal set up corner setting Uninsulated flue Insulated flue A Distance to furniture min 650 mm 650 mm Distance to flammable materials min B in front floor 300 mm 300 mm to the side floor 150 mm 150 mm E to the side combustable side wall
14. presence of children aged and or infirm persons Installation It is prohibited to carry out unauthorised alterations to the stove There must be plenty of fresh air in the room where the stove is being installed in order to ensure proper combustion Note that any mechanical exhaust ventilation e g an extraction hood may reduce the air supply Any air grilles must be placed in such a manner that the air supply is not blocked Building Regulations Approved Document J gives specific guidance on the required permanent ventilation into the room for combustion air of solid fuel appliances The floor structure must be able to carry the weight of the wood burning stove as well as the weight of a chimney if necessary When you choose where to set up your RAIS wood burning stove you should consider the heat distribution to the other rooms This will enable you to get the best use out of your stove The stove should be set up at a safe distance from inflammable materials see the manufacturer s plate on the wood burning stove Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Produced at RAIS A S Industrivej 20 9900 Frederikshavn Danmark EN 13240 2001 A2 2004 11 EC NO 835 Q Tee 57 Q Tee 65 AFSTAND TIL BRAENDBART BAGV EG ABSTAND ZU BRENNBAREN BAUTEILEN HINTEN DISTANCE TO COMBUSTIBLE BACK WALL DIST ENTRE COMPOSANTS COMBUSTIBLES ARRIERE AFSTAND TIL BR ENDBART SIDEV EG ABSTAND ZU BRENNBAREN BAUTEILEN SEITE DE
15. suitable for using for the complete chimney The chimney and connecting fluepipe must have a minimum diameter of 150 mm and its dimension should be not less than the size of the outlet socket of the stove which is 150 mm in diameter Any bend in the chimney or connecting fluepipe should not exceed 45 90 bends should not be used Combustible material should not be located where the heat dissipating through the walls of fireplaces or flues could ignite it Therefore when installing the stove in the presence of combustible materials due account must be taken of the guidance on the separation of combustible material given in Building Regulations Approved Document J and also in these stove instructions If it is found that there is excessive draught in the chimney then either an adjustable flue damper or alternatively a draught stabiliser should be fitted The adjustable flue damper should not close off the flue entirely but should in its closed position leave a minimum continuous opening free area of at least 20 of the total cross sectional area of the flue or fluepipe Adequate provision e g easily accessible soot door or doors must be provided for sweep ing the chimney and connecting fluepipe You should also familiarise yourself with the draught conditions for chimneys with 2 flues The outlet spigot is eiter 150 mm 6 in diameter or 129 mm 5 in diameter For strong draughts the chimney or flue should be fitted with a draug
16. the cause of the fume emission has been iden tified and corrected If necessary seek expert advice IMPORTANT Warning Note Do not use an aerosol spray on or near the stove when it Is alight IMPORTANT Safety advice When using the stove in situations where children aged and or infirm persons are 5 ent a fireguard must be used to prevent accidental contact with the stove The fireguard should be manufactured in accordance with BS 8423 2002 Replaces BS 6539 34 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Lighting and fuelling TIPS before firing up Open a door or window close to the wood burning If there is a storm in the stove coming trom the chimney it is advisable to place a screwed up piece of newspaper be tween the upper baffle plate and the chimney set the paper on fire and wait until you hear a rumbling noise in the chimney This means that there definitely is a draught in the chimney and you avoid smoke in the room Top Down lighting Start by placing 3 4 pieces wood approx 15 2 kilogram in the bottom of the burning My 1 kilogram of dry firewood split into kindling sticks and a couple of alcohol briguettes or similar 1 2 Set the air damper to fully open position Light the fire and close the door 3 4 leaving the door ajar approximately 10 15 mm When the flames are clear after approx 10 15 min close the door completely 5 Damper see adjustment of air damper
17. 275 225mm to the ceiling 800 mm 800 mm 21 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Installation distance in case of non combustible wall We recommend a minimum distance to non combustible material of 50 mm P for cleaning considerations It should always be possible to access the access door 22 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Mounting wall bracket and installation of Q Tee Wall The stove can only be mounted on non combustible walls without cracks Contact the chimney sweep or building expert regarding the wall s suitability RAIS recommends that hanging and installation of RAIS Q TEE WALL should only be done by authorized dealers Remove the knock outs for the wall bracket 1 and chimney 2 at rear of the stove see section Change of chimney connection Remove he blanking plate and the packing and mount them on the stove top outlet please ensure that the gasket Is properly seated Parts are screwed together with 3 M6 bolts The wall bracket 3 is centered in relation to wall pipe in the wall or at the desired distance above the floor The holes are marked up through the holes in the bracket All holes are drilled a mini mum of 2 holes must be in a brick The bracket is mounted with screws suitable to the type of wall The bracket s upper edge should be horizontal Note that the screw head is not higher than 11mm Plastic plugs are not permitted Bolts and other fastenin
18. 275 mm SIEHE BEDIENUNGSANLEITUNG DISTANCE TO COMBUSTIBLE SIDE WALL UK 275 mm SEE USER MANUAL DISTANCE ENTRE COMPOSANTS COMBUSTIBLES COTE FR 275 mm CONSULTEZ LE GUIDE DE L UTILISATEUR AFSTAND TIL BRAENDBART MOBLERING DK 650 mm SE BRUGERVEJLEDNING ABSTAND VORNE ZU BRENNBAREN MOBELN DE 650 mm SIEHE BEDIENUNGSANLEITUNG DISTANCE TO FURNITURE AT THE FRONT UK 650 mm SEE USER MANUAL DISTANCE ENTRE COMPOSANTS COMBUSTIBLES DEVANT FR 650 mm CONSULTEZ LE GUIDE DE L UTILISATEUR CO EMISSION DK 0 196 CO EMISSION IN DEN VERBRENNUNGSPRODUKTEN DE 0 196 1250 mg nm3 EMISSION OF CO IN COMBUSTION PRODUCTS UK 0 196 EMISSION CO DANS LES PRODUITS COMBUSTIBLES FR 0 196 Raumheizer f r feste Brennstoffe Appliance fired by wood Po le pour combustibles solides DK 350 mm SE BRUGERVEJLEDNING DE 350 mm SIEHE BEDIENUNGSANLEITUNG UK 350 mm SEE USER MANUAL FR 350 mm CONSULTEZ LE GUIDE DE L UTILISATEUR DK 275 mm SE BRUGERVEJLEDNING ST V STAUB DK 20 mg Nm3 DE 20 mg Nm3 DUST POUSSIERES UK 20 mg Nm3 FR 20 mg Nm3 ROGGASTEMPERATUR ABGASTEMPERATUR DK 283 C DE 283 C FLUE GAS TEMPERATURE TEMPERATURE DES GAZ DE FUM E 283 C FR 283 C NOMINEL EFFEKT HEIZLEISTUNG DK 4 1 kW DE 4 1 kW THERMAL OUTPUT PUISSANCE CALORIFIQUE UK 4 7 kW FR 4 1 kW VIRKNINGSGRAD ENERGIEEFFIZIENZ DK 80 DE 80 ENERGY EFFIENCY EFFICACITE ENERGETIQUE UK 80 FR 80 DK Br ndsel Brug kun anbefalede br ndsler F lg instr
19. E BRUGERVEJLEDNING ABSTAND ZU BRENNBAREN BAUTEILEN SEITE DE SIEHE BEDIENUNG SANLEITUNG DISTANCE TO COMBUSTIBLE SIDE WALL UK SEE USER MANUAL DISTANCE ENTRE COMPOSANTS COMBUSTIBLES FR CONSULTEZ LE GUIDE DE L UTILISATEUR AFSTAND TIL BRAENDBART MOBLERING DK 650 mm SE BRUGERVEJLEDNING ABSTAND VORNE ZU BRENNBAREN M BELN DE 650 mm SIEHE BEDIENUNGSANLEITUNG DISTANCE TO FURNITURE AT THE FRONT UK 650 mm SEE USER MANUAL DISTANCE ENTRE COMPOSANTS COMBUSTIBLES DEVANT FR 650 mm CONSULTEZ LE GUIDE DE L UTILISATEUR CO EMISSION DK 0 196 CO EMISSION IN DEN VERBRENNUNGSPRODUKTEN DE 0 126 1250 mg nm3 EMISSION OF CO IN COMBUSTION PRODUCTS UK 0 196 EMISSION CO DANS LES PRODUITS COMBUSTIBLES FR 0 196 Raumheizer f r feste Brennstoffe Appliance fired by wood Po le pour combustibles solides STOV STAUB DK 20 mg Nm3 DE 20 mg Nm3 DUST POUSSIERES UK 20 mg Nm3 FR 20 mg Nm3 ROGGASTEMPERATUR ABGASTEMPERATUR DK 283 C DE 283 C FLUE GAS TEMPERATURE TEMPERATURE DES GAZ DE FUMEE UK 283 C FR 283 C NOMINEL EFFEKT HEIZLEISTUNG DK 4 1 kW DE 4 1 kW THERMAL OUTPUT PUISSANCE CALORIFIQUE UK 4 7 kW FR 4 1 kW VIRKNINGSGRAD ENERGIEEFFIZIENZ DK 80 DE 80 ENERGY EFFIENCY EFFICACITE ENERGETIQUE UK 80 80 DK Br ndsel Brug kun anbefalede br ndsler F lg instrukserne i brugermanualen DK BR NDE Anordningen er egnet til roggassamleledning og intervalfyring DE Hinweis Lesen un
20. The stove is designed and approved in accordance with EN 13240 and NS 3058 for stok ing split dried firewood The firewood must have a water content of 15 22 and its max length should be the length of the combustion chamber minus 50 60 mm Stoking with wet firewood causes both soot environmental pollution and bad fuel economy Freshly cut wood contains approx 50 70 water and 15 thoroughly unsuitable for stoking Count min 1 year of storage time for newly cut wood before using Wood with a diameter of more than 100 mm should be split Regardless of wood size it should always have at least one surface area Tree of bark We do not recommend stoking with painted laminated or impregnated wood wood with a synthetic surface painted refuse wood chipboard plywood domestic waste paper bri quettes and pit coal as this will produce malodorous smoke which could be poisonous When firing with the above mentioned items and amounts larger than those recommend ed the stove is subjected to a larger amount of heat which results in a higher chimney temperature and lower efficiency This can result in the stove and chimney becoming dam aged and would void the warranty The calorific value of the firewood is closely connected to the moisture level of the firewood Moist firewood has a low heat value The more water the wood contains the more energy it takes for this water to vaporise resulting in this energy being lost 31 Rais Q Tee Q Te
21. alarm must be fitted in the same room as the appliance Further guidance on the installation of the carbon monoxide alarm is available in BS EN 50292 2002 and from the alarm manufacturer s instructions Provision of an alarm must not be considered a substitute for either installing the appliance correctly or ensuring regular servicing and maintenance of the appli ance and chimney system HEALTH AND SAFETY PRECAUTIONS Special care must be taken when installing the stove such that the reguirements of the Health and Safety at Work Act are met Handling Adequate facilities must be available for loading unloading and site handling Fire Cement Some types of fire cement are caustic and should not be allowed to come into contact with the skin In case of contact wash immediately with plenty of water Asbestos This stove contains no asbestos If there is a possibility of disturbing any asbestos in the course of installation then please seek specialist guidance and use appropriate protective eguipment Metal Parts When installing or servicing this stove care should be taken to avoid the possibility of personal injury Rais Q Tee Q Tee Wall Hung amp Q Tee Insert STOVE PERFORMANCE In the UK the stove has been approved by HETAS Ltd as an intermittent operating appliance for burning wood logs only PREPARATORY WORK AND SAFETY CHECKS IMPORTANT WARNING This stove must not be installed into a chimney that serves any other heating applia
22. be carried out by a registered competent electrician and in accordance with the requirements of the latest issue of BS 7671 Carbon Monoxide Alarm A carbon monoxide alarm complying with BS EN 50292 must be fitted in the same room as the appliance It should be positioned on the ceiling at least 300mm from any wall or if it is located on a wall as high up as possible above any doors and windows but not within 150mm of the ceiling The alarm should also be between 1m and 3m horizontally from the appliance Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Commissioning and handover Ensure loose parts are fitted in accordance with the instructions given in the Instruction booklet On completion of the installation allow a suitable period of time for any fire cement and mortar to dry out when a small fire may be lit and checked to ensure the smoke and fumes are taken from the stove up the chimney and emitted safely to atmosphere Do not run at full output for at least 24 hours On completion of the installation and commissioning ensure that the operating Instructions for the stove are left with the customer Ensure to advise the customer on the correct use of the appliance with the fuels likely to be used on the stove and warn them to use only the recommended fuels for the stove Advise the user what to do should smoke or fumes be emitted from the stove The customer should be warned to use a fireguard to BS 8423 2002 Replaces BS 6539 in the
23. ce of 30 cm in front of the stove and 15 cm to each side measuring from the door of the combustion chamber Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Combustion air supply In order for the stove to perform efficiently and safely there should be an adequate air supply into the room in which the stove is installed to provide combustion air This is particularly necessary if the room is double glazed or a flue draught stabiliser is operat ing in the same room as the appliance It may be necessary to increase the air vent size in property with low air permeability lt 5 0 m h m The provision of air supply to the stove must be in accordance with current Building Regulations Approved Document J An opening window is not appropriate for this purpose IMPORTANT NOTE If applicable and the appliance is being fitted within an existing fireplace recess specialist advice should be sought before fitting any permanent ventilation within this area Connection to chimney Stoves may have a choice of either a rear or top flue gas connector that allows connection to either a masonry chimney or a prefabricated factory made insulated metal chimney in accordance with their instructions In some cases it may be necessary to fit an adaptor to increase the diameter of the flue to the minimum required 150 mm section of the chimney or liner Electrical Services The installation of any electrical services during the installation of this appliance must
24. clear of obstruction and have been swept clean immediately before installation of the stove If the stove is fitted in place of an open fire then the chimney should be swept one month after installation to clear any soot falls which may have occurred due to the difference in combustion between the stove and the open fire If there is no existing chimney then either a prefabricated block chimney in accordance with Building Regulations Approved Document J or a twin walled insulated stainless steel flue to BS 4543 can be used These chimneys must be fitted in accordance with the manufacturer s instructions and Building Regulations Rais Q Tee Q Tee Wall Hung amp Q Tee Insert A single wall metal fluepipe is suitable for connecting the stove to the chimney but is not suitable for using for the complete chimney The chimney and connecting fluepipe must have a minimum diameter of 125 mm and its dimension should be not less than the size of the outlet socket of the stove Any bend in the chimney or connecting fluepipe should not exceed 45 90 bends should not be used Combustible material should not be located where the heat dissipating through the walls of fireplaces or flues could ignite it Therefore when installing the stove in the presence of combustible materials due account must be taken of the guidance on the separation of combustible material given in Building Regulations Approved Document J and also in these stove instructions If it i
25. d befolgen Sie die Bedienungsanleitung F r mehrfach belegten Schornstein zugelassene Zeitbrandfeuerst tte Nur empfohlene Brennstoffe einsetzen DE HOLZ UK Fuel types only recommended Follow the installation and WOOD operating instruction manual Intermittent operation F Remargue Veillez lire et observer les instructions du mode d emploi Foyer a dur ede combustion limit e homologu pour chemin e connexions multiples Utiliser seulement les combustibles recommand s Hergestellt f r Produced for ATTIKA FEUER AG Brunnmatt 16 CH 6330 Cham RAIS A S Industrivej 20 DK 9900 Frederikshavn fj SINTEF 15a B VG SITAC xxx XXXXX Krav anslutande 350 C Certification Bauart 2 Besigtningsorgan DTI 110 xxxx TGxxxxx DIBt Tilverkningsnummer XXX Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Revision Date 20 June 2012 INTRODUCTION kaya ao WARRANTY c Ni eebe SPECIFICATION EE INSTALLATION INSTRUCTIONS CHANGING THE CHIMNEY INSTALLATION DISTANCE TO COMBUSTIBLE WALL PLACEMENT OF Q TEE FREESTANDING CORNER SETTING 45 eege gees INSTALLATION DISTANCE TO NON COMBUSTIBLE WALL PLACEMENT OF Q TEE WALL MOUNTING WALL BRACKET am
26. e Wall Hung amp Q Tee Insert ONLY USE RECOMMENDED FUELS The following table shows the calorific value of different types of wood which have been stored for 2 years and which have a residual moisture of 15 17 Wood Kg dry wood pr m compared to beech oak Hornbeam 640 110 Beech and oak 580 100 Ash 570 98 Maple 540 93 Birch aU 88 Mountain pine 480 83 Fir 390 67 Poplar 380 65 1 kg of wood yields the same heat energy irrespective of wood type 1 kg beech merely takes up less space than 1 kg of fir Drying and storage Drying wood takes time proper air drying takes approx 2 years Here are some tips Store the wood sawn split and stacked in an airy sunny place which is protected against rain the south side of the house is particularly suitable Store the firewood stacks at a hand s breadth apart as this ensures that the air flowing through takes the moisture with it Avoid covering the firewood stacks with plastic as this prevents the moisture trom escaping It is a good idea to bring the firewood into the house 2 3 days before you need it Regulating the combustion air All RAIS stoves are equipped with a one handed operating lever for regulating the damp er The stove specific regulating mechanisms can be seen on the diagrams Primary air is the combustion air added to the primary combustion zone i e the bed of glowing embers This air which is cold is only used in the lighting stage Secondary air is the ai
27. e from the back side remove the knock out plate at the back side of the stove Mount the connection piece with the 3 M4 screws shown in picture 44 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Q TEE Function of lock for door steel block The stove is delivered with the steel block in its locking position pushed to the left as shown in the picture below The screw is then tightened When the screw is loosened the steel block can slide to the right and then the door can be lifted from the stove Be sure to tighten the screw when the steel block is in its locking position Steel block in its locking position Larger hole makes it possible to slide the steel block to the right 45 ese a L S m d s ka Wii MA m 5 e D o Lit E E lt _ gt o cs LI a lt _ gt lt gt 2 9 E Ea o i TD ry r O O 5 C1 Lo U tU B EN 3 ee eee EE ee Emet dc EP e EE LE s TETE a wr T UM e b we KC y X e y sy a 1 A el 7 e gt 9 e Ze Ee G A Kei ae BE a 6s Py ASS ALLA A SS ART sm OF FIRE Robeys For guidance purposes only this in NOT a working drawing Please
28. e up This is because the paint and materi als need to harden The odour disappears quickly but you should check the ventilation ES draught if possible See also the IMPORTANT warning notice below about persistent umes During this process you must be careful not to touch the painted surfaces and it is mended that you regularly open and close the door to prevent the door seal from sticking The stove may also produce clicking noises during heating and cooling caused by the large temperature differences which the material is subjected to Never use any type of liquid fuel for kindling or maintaining the fire You could be at risk of explosion The stove gets very hot when in use always wear protective gloves when tending the stove 4 the stove has not been used for a while follow the steps as if you were using it for the irst time IMPORTANT Warning Note Properly installed operated and maintained this appliance will not emit fumes into the dwelling Occasional fumes from de ashing and re fuelling may occur However persistent fume emission is potentially dangerous and must not be tolerated If fume emission does persist the following immediate actions should be taken a Open doors and windows to ventilate room b Let the fire out or eject and safely dispose of fuel trom the appliance c Check for flue or chimney blockage and clean if required d Do not attempt to relight the fire until
29. ely and efficiently In accordance with current Building Regulations the installer may have fitted a permanent alr supply vent into the room in which the stove is installed to provide combustion air This air vent should not under any circumstances be shut off or sealed Using the wood burning stove Adjustment of the air damper the damper has 3 settings Position 1 The damper is almost closed meaning that there is a minimal air intake Position 2 Pull the lever until first click This position gives full secondary air During normal stoking the lever is set between position 1 and 2 When the flames are clear and yellow the damper is set correctly i e resulting in a slow optimal burning Position 3 Pull the lever until next click The air damper is completely open and gives full primary and secondary air The position is for the lighting stage and Is not used under normal operation Control If the ash is white and the walls in the combustion chamber soot free after the stove has been used the air regulation was set correctly and the wood was sufficiently dry 33 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert First usage A careful start pays off Start with a small fire so that the wood burning stove can get accustomed to the high temperature This gives the best start and any damage Is avoided Be aware that a strange but harmless odour and smoke concoction may emanate from the surface of the stove the first time you fir
30. ether the wall next to where the stove is going to be installed is flammable you should contact your building contractor or the local building authorities The hearth should be able to accommodate the weioht of the stove The chimney must be independently supported by wall brackets or a ceiling support plate The weight of the stove Is Indicated in the brochure The stove should always be installed on a non combustible hearth of a size and construc tion that is in accordance with the provisions of the current UK Building Regulations Ap proved Document J If the stove is to be installed on a wooden floor it must be covered with a non combusti ble material at least 12 mm thick in accordance with UK Building Regulations Approved Document J to at distance of 300 mm in front of the stove and 150 mm to each side measuring trom the door of the combustion chamber The clearance distances to combustible material beneath surrounding or upon the hearth and walls adjacent to the hearth should comply with the guidance on the separation of combustible material given in UK Building Regulations Approved Document J and also in these stove instructions Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Placement of Q Tee 57 Q Tee 65 85 free standing Installation distance in case of combustible wall Normal set up corner setting Uninsulated flue Insulated flue A Distance to furniture min 650 mm 650 mm Distance to flammable materials
31. g material are not included in the delivery from RAIS The flue 4 with the seal is mounted on the back of the stove with 3 M6 screws instead of the blanking plate 23 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert The stove is lifted up on the wall bracket and pushed against the wall until it falls in the notch 8 IExamine that the top plate of the stove is leveled If necessary lift the stove from the wall and adjust the wall bracket SS M4 thread for set screws lt J Ss The bottom wall bracket 5 is mounted beneath the stove with 2 M6 screws 6 The middle screw 6 adjusts the stove vertically The bracket can be fastened to the wall if desired however the screws are not to be tightened because downward expansion of the stoves during heating Finally 2 M4 screws 7 are screwed on each side of the bracket and locks the stove to the bracket See the top of the page Rais Q Tee Q Tee Wall Hung amp Q Tee Insert O Tee INSERT Overall dimensions mili i TT T 25 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Assembly Instructions In case of top outlet the knock out plate of the mantle is removed Door lock oosen the screw turn the lock clock wise e Remove the front cover 1 and door 2 from the combustion chamber 6 Note that the door lock is to be turned clockwise before the door can be removed e Remove the vertical cover 4 the hori
32. ht stabiliser In which case it is important to ensure that there is a free flow through area of minimum 20 cm when the regulating gate is shut Otherwise the fuel energy may not be used optimally If at any time you are unsure about the condition of the chimney you should contact a chimney sweep Remember that access to the access door should be kept clear Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Installation The stove can be free standing the floor or hung on a non combustible wall In addi tion it may be built into a wall see specifications When installing the wood burning stove there are some rules which MUST be followed The stove must be set up and installed in accordance with all current national and local rules and regulations Local authorities and a chimney specialist should be contacted prior to set up It is prohibited to carry out unauthorised alterations to the stove There must be plenty of fresh air in the room where the stove is being installed in order to ensure proper combustion Note that any mechanical exhaust ventilation e g an extraction hood may reduce the air supply Any air grates must be placed in such a man ner that the air supply is not blocked The floor structure must be able to carry the weight of the wood burning stove as well as the weight of a chimney if necessary The stove is placed on fireproof material for the freestanding model As for the wall mounted versi
33. n last for years Do not clean with a damp cloth or any cleaning products as they can cause rust or discol ouration Only clean when cold use a brush with soft bristles or dust with a lint free cloth Only re spray when necessary The wood burning stove and the chimney must be serviced by a chimney sweep twice a year During cleaning and care the stove must be cold Cleaning the combustion chamber Scrape shovel the ash out and store it in a non flammable container uniil it has cooled down You can dispose of ash with your normal household waste REMEMBER Never remove all the ashes from the combustion chamber the wood will burn at its best with a layer of ashes of approx 20 mm Prolonged period of non use If the stove is to be left unused for a prolonged period of time then it should be given thorough clean to remove ash and unburned fuel residues To enable a good flow of air through the appliance to reduce condensation and subseguent damage leave the air controls fully open Prior to a new heating season it should be checked that the chimney and smoke gas connector are not blocked 37 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Cleaning of flue way The flue ways are consist of a smoke converter plate and a smoke chicane Both parts are made of vermaculit Handle these parts carefully Remove the smoke converter plate by tilting it to one side and turning It a little slantwise Pull out the plate carefully
34. nce There must not be an extractor fan fitted in the same room as the stove as this can cause the stove to emit fumes into the room Chimney In order for the stove to perform satisfactorily the chimney height must be sufficient to ensure an adequate draught of approximately 15 Pa so as to clear the products of combustion and prevent smoke problems into the room NOTE A chimney height of not less than 4 5 metres measured vertically from the outlet of the stove to the top of the chimney should be satisfactory Alternatively the calculation procedure given in EN 13384 1 may be used as the basis for deciding whether a particular chimney design will provide sufficient draught Please Note this appliance has been tested by the manufacturers and works on a 3m straight flue The outlet from the chimney should be above the roof of the building in accordance with the provisions of Building Regulations Approved Document J If installation is into an existing chimney then it must be sound and have no cracks or other faults which might allow fumes into the house Older properties especially may have chimney faults or the cross section may be too large i e more than 230 mm x 230 mm Remedial action should be taken if required seeking expert advice if necessary If it is found necessary to line the chimney then a flue liner suitable for solid fuel must be used in accordance with Building Regulations Approved Document J Any existing chimney must be
35. on the wall must be non combustible and must support the weight of the oven as well as a possible chimney The wall bracket accessory Is fitted with suitable bolts When you choose where to set up your RAIS wood burning stove you should consider the heat distribution to the other rooms This will enable you to get the best use out of your stove The stove should be set up at a safe distance from inflammable materials See the manufacturer s plate on the wood burning stove NOTE RAIS A S recommends that the stove is installed by a qualified competent Rais dealer or a fireplace fitter recommended by an authorized RAIS dealer See www rais com for dealer list Upon receiving the stove must be inspected for defects Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Change of chimney connection The stove is delivered ready for top outlet but may be changed to back outlet in the fol lowing way Strike out the knock out plate at the rear of stove Remove the blankino plate and the packing and position them in the hovle at the top Ensure that the packing is positioned correctly Screw all elements together with the three M6 nuts Mount the flue collar supplied by the dealer and the clamp for the upper smoke conductor with three M6x20 cylinder screws and M6 nuts Mount the parts in reverse order Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Installation distance in case of combustible wall To find out wh
36. p INSTALLATION OF Q TEE WALL Q TEE INSERT DIMENSIONS ASSEMBLY INSTRUCTIONS vw RY GR IY et xiu wai nns FOR THE INSTAEEER EE OPERATING INSTRUCTIONS gil E DRYING AND STORAGE EE REGULATION OF COMBUSTION AIR ROOM VENTILATION AND STOVES USING THE WOOD BURNING STOVE HIR o Kee E LIGHTING AND FUELLING CLEANING AND CARE CLEANING OF THE FLUE WAYS PROBLEM SOLVING ee ACCESSORIES AND SPARE PARTS SPARE PART DIAGRAN FITTING THE DIRECT AIR BOX uuu uuu u aaa Eu eni Dre LOCK BLOCK FOR STEEL DOORS QUICK EE cd DIMENSION LR O AE Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Introduction YW Thank you for purchasing a RAIS wood burning stove vy These appliances have been approved by SCA HETAS Ltd as SVG amp intermittent operating appliances for burning wood logs only e 277 A RAIS wood burning stove is more than just a heat source it also shows that you care
37. ppliance is installed see also section headed Chimney 13 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Convection RAIS stoves are convection stoves This means that the stove s back and side panels are not over heated Convection means that there is a circulation of air which ensures that the heat Is distributed more evenly throughout the entire room The cold air is sucked in at the base of the stove up through the convection channel which runs along the stoves combustion chamber The heated air pours out at the top of the stove which ensures a circulation of warm air throughout the room The stoves are equipped with a cold lever RAIS special feature which means you could almost do away with gloves Be aware however that all exterior surfaces become hot during use so take extreme care Chimney The chimney is the driving force which makes the stove function In order for the stove to perform satisfactorily the chimney height must be sufficient to ensure the correct draught of 14 to 18 Pa so as to clear the products of combustion and prevent problems of smoke emanating into the room when firing NOTE A chimney height of not less than 4 5 metres measured vertically from the outlet of the stove to the top of the chimney should be satistactory Alternatively the calcula tion procedure given in BS 5854 1980 may be used as the basis for deciding whether a particular chimney design will provide sufficient draught
38. r which is added in the gas combustion zone i e air which contrib utes to the combustion of the pyrolysis gasses preheated air which is used for the cleaner glass system and combustion This air is sucked through the damper under the combus tion chamber and is pre heated through the side channels and then emitted as hot scav enging air onto the glass The hot air rinses the glass and keeps it soot free The tertiary channel which can be seen at the top of the combustion chamber towards the back serves to combust the final gas residues 32 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert By setting the interval between position 1 and 2 the energy content in the firewood is used optimally as there is oxygen for combustion and for the burning of the pyrolysis gasses When the flames are a clear yellow the damper has been set correctly Finding the correct position comes with time after you have used for stove for a while It is not recommended that you turn it down completely A mistake commonly made is DEM the damper too early because it feels too hot This results in dark smoke ema nating from the chimney and in the calorific value of the firewood not being used to its fullest Room ventilation and stoves There must not be an extractor fan fitted in the same room as the stove as this can cause the stove to emit smoke and fumes into the room The stove requires a permanent and adequate air supply in order for it to operate saf
39. s found that there is excessive draught in the chimney then a draught stabiliser should be fitted Fitting of a draught stabiliser will affect the requirement for the permanent air supply into the room in which the stove is fitted in accordance with Approved Document J see also combustion air supply Adequate provision e g easily accessible soot door or doors must be provided for sweeping the chimney and connecting fluepipe where it is not intended for the chimney to be swept through the appliance also to permit visual checks on the integrity of the flue when the appliance is serviced Hearth The hearth should be able to accommodate the weight of the stove and its chimney if the chimney is not independently supported The weight of the stove is indicated in the brochure The stove should always be installed on a non combustible hearth of a size and construction that is in accordance with the provisions of the current Building Regulations Approved Document J The clearance distances to combustible material beneath surrounding or upon the hearth and walls adjacent to the hearth should comply with the guidance on the separation of combustible material given in Building Regulations Approved Document J and also in these stove instructions If the stove is to be installed on a combustible floor surface it must be covered with a non combustible material at least 12mm thick in accordance with Building Regulations Approved Document J to a distan
40. ss in m divided by the wall s lambda value Consult with your installer Chimney Sweep Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Installation distance in case of non combustible panels Min convection area 600 above To guide the hot air out of the convection outlets RAIS recom the stove may be distributed mends to mount a non combustible plate above the outlets A A A Distance to combustible material min 300 mm Distance to non combustible plate min 800 mm hl y Ja octal deng to the flue i y a LLL BLL LLL Cem mmmn eS oa o Do Asma mamam um mmm mmm Wamm ysam sm emm mmm mms wm mam mes mmm pm _____ ____ ____ mmm mmm mm m wm mem s ces RRG i Oo ee c E SS 1 Se ZE Min 100 mm A Distance to Min convection area 350 cm below furniture the stove may be distributed min 650 mm Min 150 mm Min 150 mm Distance to combustible Distance to combustible material material min 200 mm min 200 mm f ex door frame side wall Min 300 mm 29 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Installation distance in case of brick wall fire wall Min convection area 600 above To guide the hot air out of the convection outlets RAIS recom the stove may be distributed mends to mount a non combustible plate above the outlets A A E Ei
41. the sake of adjustment options for set screws level foundation be min 5 mm below the horizontal edge in front If an air system is fitted make sure that the stove damper is supplied with fresh air from the outside either through the back or bottom side of the stove Air system For correct function of the air system no negative pressure must occur in the housing 27 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Placement of Q Tee INSERT Convection RAIS stoves are convection stoves Convection means that there is a circulation of air which ensures that the heat Is distributed more evenly throughout the entire room The cold air is sucked in at the base of the stove up through the convection channel which runs along the stove s combustion chamber The heated air pours out at the top of the stove which ensures a circulation of warm air throughout the room Ventilation use the insert optimally Consider the placement of convection and outlet holes Ensure that the area requirements are respected and that the holes are not blocked from the outside There may be disco loration of the wall above the stove doors and above the convection outlet holes This is due to the ascending hot air RAIS accepts no liability for installation or consequential damages Material selection Choose materials for panels bricks with a thermal resistance greater than 0 03 m xK W Thermal resistance is defined as the thickne
42. ukserne i brugermanualen DK BR NDE Anordningen er egnet til reggassamleledning og intervalfyring DE Hinweis Lesen und befolgen Sie die Bedienungsanleitung F r mehrfach belegten Schornstein zugelassene Zeitbr andfeuerst tte Nur empfohlene Brennstoffe einsetzen DE HOLZ UK Fuel types only recommended Follow the installation and UK WOOD operating instruction manual Intermittent operation F Remarque Veillez lire et observer les instructions du mode d emploi FR Foyer dur ede combustion limit e homologu pour chemin e connexions multiples Utiliser seulement les combustibles recommand s Hergestellt f r Produced for ATTIKA FEUER AG Brunnmatt 16 CH 6330 Cham RAIS A S Industrivej 20 DK 9900 Frederikshavn f SINTEF 15a B VG SITAC xxx xx im DN XXXXX Krav anslutande r kkanal 350 C Certification Bauart 2 Besigtningsorgan DTI 110 0368 TG20195 DIBt x xx xx xx Tilverkningsnummer XXX Produced at RAIS A S Industrivej 20 9900 Frederikshavn Danmark EN 13229 2001 A2 2004 12 EC NO 836 Q Tee Insert Anordningen ma kun installeres i forbindelse med ubraendbart materiale AFSTAND BRAENDBART BAGV EG DK SE BRUGERVEJLEDNING ABSTAND ZU BRENNBAREN BAUTEILEN HINTEN DE SIEHE BEDIENUNGSANLEITUNG DISTANCE TO COMBUSTIBLE BACK WALL x UK SEE USER MANUAL DIST ENTRE COMPOSANTS COMBUSTIBLES ARRIERE FR CONSULTEZ LE GUIDE DE L UTILISATEUR AFSTAND TIL BRAENDBART SIDEV EG DK S
43. zontal stop for ashes 3 and remove 2x M6 hex screws 5 between the combustion chamber and the bracket 7 The nuts 11 for the bracket 12 must only be loosened and the bracket can be removed e The burning chamber is removed from the mantle e The reflector plate 9 can be removed if the installation is with a rear brick wall otherwise it is recommended in other installations e Place the mantle 8 in the wall opening adjustment is done using the 4 set screws Be aware that the mantle must be leveled and adjusted vertically and can be fastened to the side wall using angle brackets or frame screws e The remainder of the stove is assembled in reverse order e Check that the cover is parallel to the wall and flush with the steel door frame steel door or with the door glass list glass doors in the closed position if necessary adjust the stove forward or backward It desired the cover can be provided in special outer dimensions Contact your RAIS dealer This can be ordered with the stove 26 Rais Q Tee Q Tee Wall Hung amp Q Tee Insert Built in dimensions wall opening The wall opening is min 613mm x 473mm height x width The depth is min 475 mm non combustible panel and min 425mm brick A fireplace insert must never be built in tightly as steel expands during heating Brick TT 221250222 Z 22 e 22722 2222222222 2222224222 2 Z lt For
Download Pdf Manuals
Related Search