YG-200 Swing Gate Opener Owners Manual
Contents
1. 10 3 Safe guard Infrared device or Photocell 20 11 Advanced Control Wiring eeen 21 11 1 Visual Guide for Wiring nnen ennenenenn 23 13 Auto close function 23 14 Additional Features sas eere terrre 25 15 Operation Notes on the Gate Opener System 26 16 Maintenance amp Troubleshooting 27 17 Gatekeeper Ltd Limited Warranty 20 This Page Intentionally Left Blank li MEMNO PART NUMBER lI A B ACTUATOR HOUSINC PLAN AARYBASE J a MOIOR J DG MOI SCALE Dip GATE KEEPER LTD DYR s bla 7 COMPLETE ASSY A3 scab za This Page Intentionally Left Blank 1 Safety Precautions Installing the YG 5602 1 Gate Opener requires installation of standard 110V or 230V electrical wiring This work should only be performed by a trained technician Mis wiring could cause personal injury or DEATH To prevent the risk of electrocution be sure to turn off all power to the YG 5602 1 until installation is complete e Please keep hands fingers and loose clothing away from moving parts as they may be dragged into moving parts e The gate may move at any time Ensure all persons are clear of the gate when it is moving to avoid the risk of injury Do not touch the gate while it is in operation Do not attempt to go through the gate while it2. Pin 1 2 3 Fastener Screw 1 2 4 L Mounting Bracket 2 4 5 Bar Mounting Bracket 1 2 6 Nut for Bolt 2 4 7 Bolt 2 4 8 Release Key 1 2 9 Bolt 6 12 10 Cotter Pin 1 2 11 T Mounting Bracket 1 2 12 Front Clevis Pin 1 2 5e Actuator Specifications and Measurements 1 Actuator Maximum Direct Force 1400N 315 Ibs 2 Actuator Maximum Power Consumption 12V at 6A 72W 3 Duty Cycle 5096 1218mm 47 95 gt 365mm 14 3 B v E e E a S o p E E i e 2 E i 13 Actuator 150mm 5 9 16mm 62 NY i E gt e A 30mm 30mm YA 18mm18mm 1 27 1 2 1 2 qu E a Bar Mounting Bracket 30mm 1 2 150mm 5 9 15mm 59 8mm 31 late N Y io Yl 9 o m NL A E E EE SA l 20mm 20mm 20mm 20mm S T en 78 78 78 78 O T Mounting Bracket 58mm 26mm 1 BA TY WIE 3 ya 10mm 39 Elel E E SY sS E E lp Y 4 10mm 39 4mm 15 L Mounting Bracket Figure 1 6 Gate Arm Actuator Installation Before proceeding to the installation make sure you read through the following Gate Size and Weight Limitations The YG 5602 1 Swing Gate Opener will handle gates weighing up to 300Kg 6611b and up to 3 6m 12 ft per leaf if the proper installation procedures have been followed The YG 5602 gate operator operates by forcing a worm gear to extend inside each actuator pu
3. When the gate is moving at opening phase the photo sensor can be selected as active or inactive ON If photo sensor covered by the obstacle during the gate opening Phase the gate system will stop immediately OFF If photo sensor covered by the obstacle during the gate opening phase the gate system will not be affected by photo sensor 25 DIP SWITCH SLOW DOWN SPEED The final speed can be set of mn dm when the gate is moving at slow down speed ON The final speed 5576 normal speed OFF The final speed 7076 normal speed SLOW DOWN SPEED Pedestrian Start Feature The System can open only one side of the gate for pedestrian traffic For a dual gate connect the motor cables for both terminals J1 amp J2 Press the green button of the transmitter to activate Pedestrian Start For single gate connect the motor cable for terminal J1 only Press the black button of transmitter to activate Pedestrian Start 15 Operation Notes on the Gate Opener System When the gate is travelling at normal speed if the motor encounters an over current condition because of obstruction the gate will stop immediately in opening phase but for the closing phase the gate will stop and reverse back for approx 2 sec If any command transmitter keypad or photocell or other abnormal case interrupts the leaf s motion before it moves to the end of travel the gate can only be operated with slow down speed for the rest of the cycl
4. already and verify that you have completed the remote programming exercise and self learning When properly adjusted the gate should close and stop when it hits the stop block without overly forcing the gate and reverse if it strikes an object before it reaches its stop An alarm should sound if it activates the auto reverse Use a screw driver to rotate the Over Current Adj knob Rotating clockwise will increase the resistance needed to trip the safety reverse function Rotating counter clockwise will decrease the resistance If the gate does not move when activated or auto reverses without striking an obstacle then the resistance setting may be too little If the gate does not stop when an obstruction is placed in its path then the setting may be too high Start with just above the minimum value and tune it to use the minimum setting for which the gate will function WARNING Do not attempt to tune the gate by placing your hand arm or other body part in the path of the gate This could result in serious injury Also placing a heavy immovable object in the path to test with could cause damage to the gate opener motors Instead place a light object in the path preferably something like a chair or trash can which will be pushed out of the way if the setting is still too high without causing damage to the gate motors Note this auto reverse function should be regularly inspected and adjusted if necessary Once this step is complete replac
5. in the YG 5602 in the electrical section The YG 5602 requires at least a 15A service Make sure your electrician takes into account the voltage drop involved in running many feet of wire to your installation location If an insufficient gauge of wire is used there will be insufficient power at the site to operate the opener 5b Solar Power If you plan to use solar panels to power your gate verify that you have sufficient solar power to charge the battery and provide power for the number of openings and closings you plan to need Different areas of the planet receive varying amounts of sunlight and that amount varies on the time of the year Make sure you account for all this in any solar installation If insufficient power is available the opener battery can be permanently damaged and this is not covered under the warranty 5c Equipment Check Swinging Gate Actuator T Mounting Bracket Flashing light Through beam type infra red photo sensor Electric Latch with Keylock Mounting bracket Antenna Control box Cotter Pin 10 Clevis Pin 11 Keys and manual key lock CP ONATR YN 12 Remote key Not shown in picture 1 Stop Block 3 Bar Mounting bracket 2 L Mounting bracket 4 Assorted bolts and nuts 5d Parts for Gate Arm Installation You need the following parts to connect an actuator to your gate No Description EID I 1 Actuator 1 2 2 Nest
6. is still in motion This opener is intended for vehicular use only e Donotallow children or pets near your gate Keep the remote controls away from children Place controls where they cannot be accessed by reaching through the gate e To avoid electric shock unplug unit before opening case e Make sure the battery inside the opener is charged fully before using e Before installation the clutch should be unlocked e The auto reverse function must be checked during installation to ensure that the gate can auto reverse in the event of obstruction and it should be inspected regularly e The automatic gate opener must be grounded e Install the gate opener on the inside of the property DO NOT install it on the outside of the property where the public has access to it e Additional safety equipment such as photoelectric sensors safety edges roller guards and warning signs must be installed to prevent injury e Inthe event of power failure an emergency release key allows you to operate the gate manually e Please erase and reset the code after installing the opener e The gate opener should be installed by a qualified technician otherwise serious personal injury or property damage may occur For service call an experienced technician Do not in any way modify the components of the automated system otherwise serious personal injury or property damage may occur We do not accept responsibility for damage or injury resultin
7. leaf s travel Transmitter or Push button or other abnormal stop the System Self Learning Process will not be successful and the System Self Learning Process must be repeated again from the beginning In case of the absence of a power supply the stored learning memory will be lost and the systems should execute the System Self Learning Process again 17 9 Using the RF Remote Control BUTTON 1 Main button Opens both gates Used for registering control BUTTON 2 Pedestrian button Opens single gate if enabled Fig 8 WARNING Notify the users that the gate is never to be operated unless it is in full view How to add an additional remote control Please press button SW2 the L4 LED for code learning will be turned on and the receiver module will be changed to the RF Remote Learning Mode for 30 seconds During the RF Remote Learning Mode period press the main button one black one on the left of the transmitter it will then be memorized up to 15 different transmitters can be memorized After the LED light is turned off the receiver module will go back to the normal mode and the system can be operated normally Up to 15 remote controls may be used Additional RF Remote controls can be obtained through your dealer To find a dealer go to www gatekeeperltd com dealers How to erase remote controls To erase existing remote controls the memory can be cleared completely if the SW2 code lea
8. 2VDC Max current 3A Ja Terminal block 7 amp 8 Connect to the flashing light 12VDC Max power 15W J4 Terminal block 13 ve amp 12 ve Connect to the external receiver board for the 12 V DC Positive and Gnd Negative J4 Terminal block 10 Connect to the push button or external receiver board for the dual gate operation J4 Terminal block 11 Connect to the push button or external receiver board for the single gate operation J4 Terminal block 12 to 15 e If using the photo sensor connect the two one is transmitter and other is receiver photo sensors VDC to 13 and GND to 12 e Connect the N C to 14 and COM to 15 e If NOT using the photo sensor make a jumper between 14 and 15 Otherwise the systems can t operate J5 Terminal block 16 Connect Aerial cable J6 Terminal block J6 Connect to the Reset Switch SW2 This button is used for code learning VR1 Over current limit can be adjusted from min 3 5Amp to Max 7 5Amp VR2 Close delay can be adjusted from min 0 second to Max 8 second 22 11 1 Visual Guide for Wiring J1 Block J2Block J3 Block J4 Block Aerial M 1 M2 Latch Light 12V PB2 PB1 GND 12V PHOTO ANT PHT GND L9 10 11 2 o E z Slave Gate 23 12 Auto reverse function It is very important that you tune the safety reverse function on your gate opener Power the control box if it is not
9. GRAM om Ground Live Neutral AC input J7 DC input J8 Green Hot White Battery Earth Black Blue inside he EE n 8 1 Connecting the AC Power The control box should be equipped with a single phase breaker 15A Make sure that the power is OFF before making any electrical connections Remove the cover of the control box perform the wiring and replace the cover again Wire your AC line into the AC IN terminal at the top of the control box near the transformer e Wire the ground usually green to the terminal on the left e Wire the hot usually black wire to the middle terminal e Wire the neutral usually white wire to the terminal on the right Verify that all electrical connections are waterproof by installing electrical outlets into exterior grade boxes with waterproof covers Make sure that whenever an electrical connecter enters or exits a box it is sealed If using solar verify that all connections are waterproof Please Note the system cannot execute the learning mode remote control by battery power only Once your breaker is activated the LED should light 15 8 2 Wiring the Battery see Fig 7b Inside the control box connect the red battery lead to BAT terminal of control board and black battery lead to BAT Use terminal J8 for the battery pe uus i a i Battery Da RED WIRE TO POSITIVE RE feces B PES m wo AS BLACK WIRE TO POSITIVE EN L e M Figure 7b D
10. GatekeeperLtd www gatekeeperltd com mm TR TIR JI saat 3 63 63 3E36363 E LL Guard Your Yard YG 5602 1U E SWINGING GATE OPENER OWNER S MANUAL Ce 2012 Gatekeeper Ltd P O Box 752 Lacey s Spring AL 35754 http www gatekeeperltd com Table of Contents ls Safety PrecatttOllS soes nevens 3 PM EL 4 3 Specifications aiw LE AEO WOS 4 4 Necessary Tools and Equipment 5 SWOI Prepar Oieee RR 5 AES CE UR PONTO estaca ariano 5 DOL DOSE ai O AAA AWATA 5 SC Equipment CHECK nanne a 6 5d Parts for Gate Arm Installation e 7 5e Actuator Specifications and Measurements 8 6 Gate Arm Actuator Installation 9 6a Determine Gate Open Direction asana 10 6b Pull to Open Ui Ward severe tinte es Ma Cr ve ao Pa CA 11 6c Push to Open Outward nerede setes 12 7 Stopper and Latch Installation 13 5 Electrical Installation IA 15 8 1 Connecting the AC POWOE eiecit ro aetate heus 15 8 2 Wiring the Battery see Fig 7b nnee eeen 16 8 3 Wiring the Actuators eeeeseeeeeeeeeeene nnn 16 8 4 First Time Activation Test eese 17 9 Using the RF Remote Control 17 IO External Interfaces nanasan eneen 19 10 1 Keypads Button Switch ieu ater EEG 19 10 2 Loop Gee EOD icd set O p dota Dads 19
11. d 15 Attach the normally closed wire to 14 and the other common normally closed wire to 15 COM Attach the 12VDC power for the photocell to 13 and the DC power to 15 The signal wires are not polarized so they can be interchanged without issue but the power wires must be wired correctly to prevent damage Consult your device manufacturer s documentation for details In the closing phase if an obstacle breaks the infrared beam of the photocell then the gate will stop and reverse after approx 3 seconds In the opening phase the function of the photo sensor can be selected between active or passive If the photo sensor is set for the active mode and the infrared beam is broken then the system will stop and wait for a new command The infrared device is included in your kit additional devices can be obtained through your dealer To find a dealer go to www gatekeeperltd com dealers 20 11 Advanced Control Wiring J7 AC 12 V J8 DC 12 V VR1 Over Current DIP INPUT Battery INPUT VR2 Close Delay Switches F1 amp F2 J6 9 to 15 Fuses 182 3 amp 4 UY J4 L Reset J1 J2 Electric Lock Additional Aerial SW2 Master Slave Flashing Light Functions antenna CodeL F1 fuse maximum 0 54 PCB F2 fuse maximum 15A Over current JI 1 amp 2 MMI Master gate J2 3 amp 4 SM2 Slave gate J3 5 amp 6 Electric lock 12VDC Max current 5A J3 7 amp 8 Flashing light 12VDC Max powe
12. e The function is guaranteed for the maximum safety during the operation Kickback extra push This is usually employed to help the electric lock insertion and release during bad weather conditions wind ice etc Open Closing delay SM2 slave motor delay at opening System is designed for a fixed time delay about 3 seconds between the first gate MM1 and the second gate SM2 during the gate opening phase MMI Master motor delay at closing Delay time can be adjusted from Min Osec to 15sec Automatic mode At the end of pause period the gate will close automatically but if a new command transmitter keypad photo sensor or over current is supplied before the end of travel this new command will cause the gate to reverse its motion Stop Reset If the reset switch is off the gate systems will not work 26 16 Maintenance amp Troubleshooting Battery overheating Check the wiring of the battery and make sure that it is well connected and using the correct polarity The gate doesn t work after pressing remote control 1 Check if the LED used for SLOW DOWN POWER is lighted Check if the voltage of the battery is less than 10 5 VDC Check the LED used for push button is lighted Turn the power off disconncect J7 J8 for 30 seconds then turn it back on and repeat the learning process 4 Check to see if the fuse is burned out Motor speed is slower than exp
13. e the cover and install the rubber caps over the screws e OVER CURRENT SENSITIVITY OVER CURRENT SENSITIVITY The limit of Over Current can be adjusted from Min 3 5Amp to Max 7 Amp for gate closing can be adjusted from Min 0 second to Max 8 second 9 CLOSE DELAY The time for the SM2 slave leaf start delay CLOSE DELAY 24 13 Auto close function This feature can be selected to make the gate stay open for some time before it automatically closes The auto close time can be adjusted to 12 25 or 50 seconds DIP SWITCH4 ON AUTO CLOSE DIP SWITCHS AUTO CLOSE2 AUTO CLOSE1 The function of auto close or without auto close can be selected AUTO CLOSE2 The function of auto close or without auto close can be selected DIP4 Auto close1 DIP5 Auto close2 Function OFF OFF Without auto close function OFF ON Auto close On waiting time 50 seconds ON OFF Auto close On waiting time 25 seconds ON ON Auto close On waiting time 12 seconds Cancel auto close function Move the fourth and fifth DIP switches to the off position in order to disable the auto close feature 14 Additional Features DIP SWITCH1 LIGHT DELAY DIP SWITCH2 OPENING PHOTO LIGHT DELAY Flashing light delay on or off ON The flashing light starts 5 seconds ahead of gate moving OFF The flashing light starts and gate starts moving at same time OPENING PHOTO
14. ected Check to see if the gate stopped because of the push button photo sensor or over current obstruction Check to make sure that the battery and transformer J7 J8 is well connected The gate stopped during the operation opening or closing Check to make sure that the Reset switch is on and that the reset switch is well connected with terminal J6 Adjust the VR1 Re set the over current limit at the proper position 3 Check the wiring of the motor is well connected Check that the jumper for the photocell is in place or that the IR Photo Safety Sensor is in place and functioning Check to see if the fuse is burned out The gate doesn t work or the gate works only in one direction Check to make sure that the Reset switch is on and that the reset switch is well connected with the terminal J6 Check that the wiring of the motor is well connected Check that the jumper for the photocell is in place or that the IR Photo Safety Sensor is in place and functioning 27 Gate auto close function works like auto open 1 The first operation should be defined as gate closing during the learning mode no matter what the method of installation is 2 If the gate executes the contrary action please swap the wiring of the motor to the opposite polarity Gate doesn t stop immediately when it reaches the end of travel 1 Adjust the VR1 t
15. efinition of flashing light codes Quick flashing light Systems operation is at slow down speed or the system is in learning mode kickback extra push phase Normal flashing light System is operating at the full speed Slow flashing light Gate is waiting for auto close execution Lamp fixed light 7 sec Gate is in a waiting mode since the photocell has been covered without gate movement by obstacle during the gate closing or opening 8 3 Wiring the Actuators Connect the wires from the master or number one gate actuator to the MM1 terminals 1 amp 2 on the control board Connect the wires from the slave or number 2 gate actuator into the SM2 terminals 3 amp 4 on the control board If using a single gate only then connect the single actuator to MM1 only Make sure that the actuators are mounted so that when activated they will close i e mount the actuators so that the gate is open actuators are retracted 16 8 4 First Time Activation Test Two Gate Operation Press the button for channel 1 button 1 on the remote control on some remote controls the black button and the programming systems will enter into system self learning mode The lamp will start quick flashing and the motors one by one will start moving through the following steps Slave Gate will Close actuator extending gt Master Gate will Close actuator extending Master Gate will Open actuator retracting Slave Ga
16. g from the installation of this opener 2 Features Class I A vehicular gate opener or system intended solely for use in a single family home or an associated garage or parking area ADDITIONAL FEATURES Supports single or dual gate operation Adjustable auto reverse function for safety purposes Built in battery backup in the event of power loss Auto close feature with 3 wait times 12 25 50 selectable by dip switch Battery low voltage detection to avoid battery damage Automatic slow down feature to decrease noisy closing Keypad single button interface Infrared safety beam interface Supports up to 15 RF remotes 2 included User programmable and user erasable remote codes RF hopping code technology prevents thieves from guessing your remote code Manual key release design for emergency purposes Supports Keypad interface and Magnetic Loop Detectors simultaneously 3 Specifications Power Supply U Model 110V AC 60Hz E Model 230V AC 50Hz Backup Battery 12VDC 4AH Maximum Number of Remote Controls 15 2 Included Maximum Gate Weight 300 KG 661 Ibs Maximum Gate Width 3 6 meters 12 feet per leaf Duty Cycle 50 Working Temperature Range 20 C 55 C 4 F 131 F Power Consumption AT 5W Standby Power Supply of the Motor 12VDC 8A 96W MAX Power Supply of the Lamp 12VDC 21W MAX Power Supply of the Electric Loc
17. k 12VDC 60W Max Power Supply of the Receiver 12VDC 2W Max Power Supply of the Accessories 12VDC 3W Max Over current protection 3 5A 7 5A Pause Time Programmable 0 sec 50 sec 2rd Leaf Closing Delay Programmable 0 sec 8sec 300 x 245 x 90 mm 4 6kgs Wawa eRe a 11 8 x9 65 x3 5 10 1 Ibs 4 Necessary Tools and Equipment The following tools may be necessary to install the YG 5602 1 Gate opener e Standard and Philips screw drivers e Electric drill e Wire cutters e Wire stripper e Socket set e Welder 5 Site Preparation Before you begin the opener installation check the following 1 The gate should be mounted and moving freely with little resistance in movement 2 The gate and post must be suitable for being automated Check that the structure is sufficiently strong and rigid and that its dimensions and weights conform to those listed in the specifications table of this document page 5 3 Make sure that the gate is plumb and level The fence posts must be mounted in concrete 5a Standard Power The YG 5602 is normally powered by U E standard power U model 110V 60Hz AC E model 240V 50Hz AC power If you have not already done so wire a waterproof outlet near the gate following proper safety standards for your area If you are not experienced with this type of wiring or if your area requires it hire a professional electrician to perform this as well as wire
18. ntrol board Magnetic loops usually require DC power using the and DC terminals Connect the 12V to 9 and the V DC to 12 They provide a normally open momentary switch interface to the control board and its ground or common interface Wire the magnetic loop s normally open trigger wire to terminal 10 and the normally open ground or common to GND 12 both on block JA Consult your device manufacturer s documentation for details See Figure 4 for a diagram of external interface connections The Loop Detector device can be obtained through your dealer To find a dealer go to www gatekeeperltd com dealers 19 10 3 Safe guard Infrared device or Photocell It is recommended that the installer install the included infrared photocell for additional safety Photocells work by inhibiting the movement of the gate if the beam is broken Infrared safety devices may be required by law in some areas If the infrared beam is broken during closing the gates will reverse and open immediately During opening the beeper will ring Infrared photocells come in active and passive varieties Active photocells require power on both sides of the driveway whereas passive photocells employ a reflector plate so that power is only required on one side of the driveway Most photocells will provide DC power input wires and and 2 normally closed switch wires To install the photocell remove the short circuit wire between Terminals 14 an
19. o decrease the over current limit Flashing light doesn t work Check the wiring of the flashing light to make sure that it is well connected and using the correct polarity Check that 18V AC is present on the output side of the transformer Check that 14VDC is present on the terminals of the battery when the unit is plugged into AC and that at least 12V DC is present when it is not plugged into AC but after charging 28 17 Gatekeeper Ltd Limited Warranty Gatekeeper Ltd warrants the YG 5602U E Swinging Gate Opener to be free of defects in materials and workmanship for a period of 1 year from the date of purchase subject to certain limitations This warranty shall not apply in the following circumstances misuse vandalism accident neglect unauthorized repair or modification acts of God lightning flood insect damage etc power surge corrosive environments incorrect installation or application damage to mechanism due to wrong type of gate incorrect weight and gate not operating freely or not on level ground etc The warranty set forth here shall be entirely exclusive and no other warranty either written or oral is expressed or implied Gatekeeper Ltd specifically disclaims any and all implied warranties of merchantability or fitness for a particular purpose It is the purchaser s sole and exclusive responsibility to determine whether or not the equipment will be suitable for a particular purp
20. ose In no event shall Gatekeeper Ltd be held liable for direct indirect incidental special or consequential damages or loss of profits whether based on contract tort or any other legal theory during the course of the warranty or at any time thereafter The installer purchaser and or end user do agree to assume all responsibility for all liability in use of this product releasing Gatekeeper Ltd of all liability For service under this warranty please contact your dealer All parts accessories service and support for Gatekeeper products is supplied through our network of dealers Dealer information can be obtained at www gatekeeperltd com dealers 29 Gatekeeper Ltd P O Box 752 Lacey s Spring AL 35754 info gatekeeperltd com For updated versions of the manual see http www gatekeeperltd com For Additional Remotes Infrared Photo Cells or Parts please contact your dealer To locate a dealer please visit us at www gatekeeperltd com dealers 2005 2012 GatekeeperLtd All Rights Reserved
21. r 21W J4 9 Positive Supply 12V DC J4 10 use with 12 Keypad Pushbutton for the dual gate operation J4 11 use with 12 Keypad Pushbutton for the single gate operation J4 12 Logical and Power Ground for external devices J4 13 Positive Supply 12V DC J4 14 amp 15 Photo sensor contacts must be shorted together if no photocell J5 16 Aerial Antenna cable Connect to Aerial for increased range J6 Reset Switch SW2 This button is used for code learning VR1 Over current limit can be adjusted from min 3 5Amp to Max 7 5Amp VR2 Close delay can be adjusted from min 0 second to Max 8 second 21 See the table on the next page for more information regarding each terminal F1 F1 fuse maximum 0 5A The fuse protects the electronic control board in case of short circuit from receiver or photo sensor F2 F2 fuse maximum 15A This fuse is part of the Safety design for the over current protection during the system operation JA MMI Terminal block 1 amp 2 Connect the cable to the MMI for the master gate In gate opening operation the master gate should be opened first Important connect only this interface if only using the single gate J2 SM2 Terminal block 3 amp 4 Connect the cable to the MM2 for the slave gate In gate closing operation slave gate moves ahead of master gate with a few second of close delay J3 Terminal block 5 amp 6 Connect to the electric lock 1
22. re Failure to do so may cause opening and closing problems 12 7 Stopper and Latch Installation WITHOUT Electrical Latch 1 Install Stopper 1 stops gate in closed position 2 Install Stoppers 2 stops gate in maximum opened position STOPPER 2 Ck do E d NSTOPPER 2 STOPPER 1 ER Figure 6a With Electrical Latch OPTIONAL 3 Install the Electrical Latch and the Slave Gate Stop on the gate as shown in the diagram 4 Install the L Bar on the opposite gate 5 Install Stopper 1 stops gate in closed position 6 Install Stoppers 2 stops gate in maximum opened position SLAVE GATE STOP pageone LATCH ue Tes STOPPER 2 NL BAR A maa d NSTOPPER 2 STOPPER 1 ax e SEES Figure 6b See YG Series Lock Installation Cross Section on the next page to understand how the Electrical Latch functions 13 YG Series Lock Installation Cross Section View Release here LOCK 8 10 Measurements in CM To install the base plate of the lock fix the plate to the ground with 3 screws and make sure that the lockpin can fit tightly in the hole in the plate ELECTRIC LOCK BASE PLATE Figure 6c Mechanical Maintenance Regularly verify that the gate swings freely Add grease to the gate as directed by the manufacturer of the gate Check that wiring and other electrical parts are weather proof Keep opener clean at all times 14 8 Electrical Installation CONTROL BOX DIA
23. rning is pressed continuously for 10 seconds 18 10 External Interfaces 10 1 Keypad Button Switch The YG 5602 is equipped with an interface for an external switch or keypad The interface type is a NO Normally Open momentary switch to ground To activate the opener the keypad or other device must short the GND 12 and Push Button 2 10 terminals momentarily on Box J4 This type of switch is very common To install the device attach one lead of your keypad to the Push Button 10 terminal and the other to the GND 12 terminal If your keypad requires 12Volts DC then you can connect the 12V to 9 and the V DC to 12 The keypad will function in single channel mode just like the RF remote If the gate is closed then activating the keypad will open the gate If the gate is open then activating the keypad will close the gate If the gate is moving then activating the keypad will stop the gate Consult your device manufacturer s documentation for details The keypad device can be obtained through your dealer To find a dealer go to www gatekeeperltd com dealers 10 2 Loop detector A magnetic loop detector detects vehicles that are within proximity to the gate A magnetic loop detector can be used to open the gate when a car pulls up either from the inside or the outside depending on which side of the gate you install it A magnetic loop is usually buried under the ground and the wires run to the gate opener co
24. roperly installed Open Inward actuator 10 6b Pull to Open Inward Mount the actuators on the included brackets according to the figure below The gate is mounted on one face of the mounting post and the opener is mounted on the face 90 degrees from it The actuator mechanism should always be inside the property so that it cannot be tampered with from the outside Initially mount the actuators on the gate so that the gate is open Figure 4 Opening Acm Ainch Bem Binch Ccm Cinch Dem D inch Angle 90 17 5 6 88 145 5 7 117 8 46 38 6 5 2 56 110 18 7 08 9 5 3 74 118 3 46 57 6 5 2 56 The installation should meet the specifications shown in the figure Failure to do so may cause opening and closing problems 11 6c Push to Open Outward Mount the actuators on the included brackets according to the figure below The gate is mounted on one face of the mounting post and the opener is mounted on the face 90 degrees from it The actuator mechanism should always be inside the property so that it cannot be tampered with from the outside Initially mount the actuators on the gate so that the gate is open Figure 5 Opening Acm Ainch Bcm Binch Ccm Cinch Dem D inch Angle 90 8 5 3 34 13 5 12 97 38 12 6 5 2 56 110 125 4 92 11 4 33 859 33 82 6 5 2 56 The installation should meet the specifications shown in the figu
25. shing or pulling the gate open Gate preparation Be sure the gate is properly installed and swings smoothly before installing the YG 5602 swinging gate opener The gate must be plumb level and move freely More detailed instructions on page 6 Sec 5 Site Preparation Conduit In order to protect the wires use PVC conduit for wires It may be necessary to preset the conduit into the concrete when it is poured Wires within the conduit shall be located or protected so that no damage can result from contact with any rough or sharp part More detailed instructions on page 6 Sec 5a Standard Power amp 5b Solar Power PVC Conduits are usually pipes but are also available as flexible tubes Once the gate is mounted adequately and electrical power is available you are ready to proceed with the YG 5602 installation 6a Determine Gate Open Direction Begin with both openers unlocked Next identify if this will be a push to open or a pull to open installation In either configuration the gate is mounted on one face of the mounting post and the opener is mounted on the face 90 degrees from it Below are schematics of both push to open and pull to open configurations A PULL TO OPEN INWARD Use this setup to make your gate open inward toward your property Figure 2 B PUSH TO OPEN OUTWARD Use this setup to make your gate open outward away from your property Figure 3 A p
26. te will Open actuator retracting gt Slave Gate will Close actuator extending gt Master Gate Will Close actuator extending Single Gate Operation For the single gate when the system receives a signal from channel 2 the lamp will start quick flashing but the system will execute learning motion after 75 sec The learning mode will execute as the following step Master Gate Close actuator extending gt Master Gate will Open actuator retracting gt Master Gate Will Close actuator extending Verify open direction If the gate does not move in the desired direction then you will need to reverse the motor operating direction No matter which method of installation is used pull to open or push to open the first operation should be defined as gate closing phase during the procedure for learning If the system executes the opposite motion during the learning mode please swap the wires of the motor to the correct polarity Determine if Adjustment is Required During the system learning mode there are two situations that need to be adjusted for using the VR1 over current sensitivity obstruction sensor e If one leaf stops before arriving at the end of travel e If one leaf stops at end of travel but the other leaf is not moving and the lamp is still quick flashing After adjusting the VR1 repeat the self learning system from the beginning Important During the System Self Learning Process if any command interrupts the
Download Pdf Manuals
Related Search