Home

Multi-Loader menus - Schneider Electric

1. BBV48778 06 2014 23 Multi Loader menus Parameter settings Batteries The diagram below shows the Parameters Battery menu accessible from Main menu Parameters Battery Charge level This menu displays the Multi Loader charge level Battery Alarm level This menu is used to set message activation at a particular charge level It warns the user about the battery charge status according to the value set see message fault detected on page 25 Battery Set battery type This menu is used to select the type of battery used by the Multi Loader normal batteries or rechargeable batteries Users must ensure that the correct battery type is selected so that the Multi Loader can accurately display the charge level This also affects message activation Parameters lt Battery Battery Battery gt Battery K Charge level gt Alarm level gt m v Set battery type Charge level MAA O78 Press and hold the up or down arrow key to define this level value more quickly Value between O and 50 Alarm level Set battery type 20 MOS Alarm level NN Save this level Normal o L Set battery type Rechargeable Save the battery type 24 BBV48778 06 2014 Multi Loader menus
2. BBV48778 06 2014 31 Downloads SoMove software SoMove allows you to prepare the configurations to be loaded onto a device It is freeware available for downloading from www schneider electric com Device update file Contact your local Schneider Electric Customer Support Center for all device firmware updates Multi Loader updated file To request Multi Loader update files contact your local Schneider Electric Customer Support Center or download it directly from the Schneider Electric website www schneider electric com 32 BBV48778 06 2014 Lists of faults codes A DANGER UNINTENDED EQUIPMENT OPERATION DUE TO TRANSFER INTERRUPTION If an interruption occurs during the transfer of configuration to the device e Identify and correct the cause of interruption e Repeat the transfer Failure to follow these instructions will result in death or serious injury General Specific application FW Flash FW Wrong memory write detected Flash FW Wrong communication detected FAULT 0x01 FAULT 0x21 0x31 Flash FW Wrong check at the end of the upgrade Flash FW Wrong reference detected FAULT 0x02 detected FAULT 0x22 0x32 Flash FW Interruption connection detected or wrong Flash FW Wrong communication detected baud FAULT 0x11 file FAULT 0x23 0x33 rate Flash FW Missing file on the SD card Flash FW Wrong prog
3. Parameter settings Diagnostics The diagram below shows the Parameters Diagnostic menu accessible from Main menu Parameters Diagnostic Fault History This menu accesses the detected fault history Diagnostic Clear Faults This menu is used to clear the detected fault history o y Parameters Diagnostic ia o Diagnostic Diagnostic a Fault Hi ah faul t History A Do C aults Tu Fault History Eso Are you sure to Eso List of cleared fault 1 clear faults faults codes y em Zus D _ yv Fault History See the table of fault 2 faults codes below u i y y Fault History Esc Clear faults fault 3 History done A DANGER UNINTENDED EQUIPMENT OPERATION DUE TO TRANSFER INTERRUPTION If an interruption occurs during the transfer of configuration to the device e Identify and correct the cause of interruption e Repeat the transfer Failure to follow these instructions will result in death or serious injury Make sure you have a set of replacement batteries to hand as the current set have little life left Remains not enough time of use The battery charge is low The appearance of this message depends on the charge level defined by the user See setting the detection page 24 Alert Low Battery Level Switch off The battery char
4. Wrong The password is incorrect Enter the password correctly the default password password is 000 SD card The cadis not recoanized Check that the SD card is inserted correctly fault 9 j Check that the SD card is formatted correctly FLSH MSD Check that the SD card is inserted correctly Eror Incomplete or incorrect Multi Loader update Check the version files for updating Multi Loader See page 31 26 BBV48778 06 2014 Multi Loader menus Parameter settings Password Parameters Password FW The diagram below shows the Parameters Password FW menu accessible from Main menu Parameters Parameters Password FW This code helps protect the device from accidental firmware updating No Parameters Password FW 0 Is there a Wrong password No password Yes Old password 000 X Old password NNN Press and hold the up or down arrow key to define the password more quickly 1 Is the password correct Yes Y New password 000 DG Y New password NNN 9 Password saved firmware updating protected Value between 000 and 999 Default value 000 Press and hold the up or down arrow key to define the password more quickly BBV48778 06 2014 27 Multi Loader menus Parameter settings Display The dia
5. The user downloads the device s specific update file update file 2 The user transfers the device s firmware update file from the PC y Z E to the Multi Loader s SD card See Connection to a PC on page 13 ZS oA 3 The user selects and then transfers the product s firmware update file from the Multi Loader to the drive See the procedure on page 30 2 Transfer the update file 4 Transfer via Quick Store 4 Once the initial transfer is completed the user can use Quick Store mode which allows the Multi Loader to load the same updated file on several devices All representations of the ATV12 drive throughout this document are given by way of example only to symbolize a device Please refer to the device compatibility tables on pages 15 and 29 All bold blue text in the manual e g Main menu Action corresponds to the messages displayed on the Multi Loader screen 8 BBV48778 06 2014 Receipt of the Multi Loader Product reference Check that the product reference printed on the label is the same as that on the delivery note This should also correspond with the number on the purchase order Contents of the Multi Loader box VW3A8121 Check that the Multi Loader box contains the following e 1x Multi Loader e 4x LR6 AA batteries e 1x SD card 1 x standard USB type A to Mini B cable e 1x RJ45 RJ45 RJ45 cable e 1x RJ45 female female adapter VW3A1 105 e 1xcarry case e 1 x simplified manual Engl
6. Configuration suitable for your application Failure to follow these instructions will result in death or serious injury This procedure allows the user to select the configuration file to be transferred to the device and use the Quick Store function see page 22 to duplicate configurations The user must already have Loaded the device configuration file cfg onto the Multi Loader see page 16 Or Generated the configuration file using SoMove and loaded this file onto the Multi Loader filename1 filename 2 etc Main menu Action a Action Config m MLD gt Device Store config Successful Store config dl g an 2 E T T T gt Y MLD gt Device MLD gt Device N MLD gt Device Store config Filenamel Filename2 FilenameN Successful Device 3 pe e Store config Successful Device 4 Y FilenameX gt gt gt gt y Store config A Y Successful Device n FilenameX gt gt gt gt gt gt gt gt 3 Y 4 FilenameX em gt gt gt gt gt gt gt gt gt gt gt UA Turn the Multi Loader on using the ON OFF button F see page 11 e Connect the Multi Loader to the device using the RJ45 cable see page 14 Press ENT when the screen displays Main menu Action Press ENT when the screen displays Action Config MLD gt Device Select the file to be transferred using th
7. display Schneider lectric Status Bar section 1 Multi Loader is PC connected to PC Multi Loader is en connected to USB Power supply Status Bar section 1 Status Bar section 2 Ts Multi Loader is Y sending 5VDC to device Multi Loader is 10y sending 10VDC to device Multi Loader is po getting 10V input from device Status Status Bar section 3 Bar section 4 Status Bar section 3 3 Multi Loader is BATT running on Battery power Multi Loader is ee running on USB power Multi Loader is running on RJ45 14 bower 3 Oo 8 8 g Fear Fise fus m mu m m Ir Status Bar section 4 Battery full Battery 75 Battery 50 Battery 25 Battery low less then 20 BBV48778 06 2014 Connecting the Multi Loader This section describes the various ways of connecting the Multi Loader Connection to a PC There are Or two ways of storing files on the SD card Insert the SD card in the Multi Loader and connect the Multi Loader to the PC with the standard USB type A to Mini B cable see Figure 3 below The Multi Loader is power supply by the PC Insert the SD card in the SD card reader on the PC see Figure 4 below A USB type A connector B USB Mini B type connector SD card reader Figure 3 Figure 4 For both these methods the SD card is recognized as an external storage device no driver is required The SD card operates in Windows Explo
8. serious injury BBV48778 06 2014 a Documentation structure The following Multi Loader documents are also available on www schneider electric com Simplified manual This manual is a simplified version of the user manual It is delivered with the Multi Loader User manual This manual describes how to connect configure and update the Multi Loader 6 BBV48778 06 2014 Setup procedure 1 Receive and inspect the Multi Loader Check that the reference printed on the label is the same as that on the purchase order Remove the Multi Loader from its packaging and check that it has not been damaged in transit 2 Connect the Multi Loader see page 13 uToaPC o To a device 3 Duplicate device configurations see page 16 and 17 O Load a configuration onto the Multi Loader o Transfer a configuration to a device o Transfer a configuration to several devices Quick Store 4 Multi Loader menus see page 18 BBV48778 06 2014 7 Introduction The Multi Loader is a standalone tool for transferring configuration files to devices with their power on or off The Multi Loader is used to set device parameters by loading a configuration file onto the device s Devices must have the same reference A consistency check is performed before the data transfer On some devices the parameters can be set with them still in their box or before they are powered up This portable tool has been designe
9. sibility is assumed by Schneider Electric for any consequences arising out of the use of this product 2013 Schneider Electric All Rights Reserved BBV48778 06 2014 Before you begin Read and understand these instructions before performing any procedure with this product A DANGER UNINTENDED EQUIPMENT OPERATION e Read and understand this manual before installing or operating the Multi loader Any changes made to a device using the Multi loader must be performed by qualified personnel Read and understand the device manuals before you load or duplicate the Configuration from one device to another device e Ensure that you select the Configuration suitable for your application e Before you load a new product firmware read and understand the procedure transferring the device update file described on page 30 Failure to follow these instructions will result in death or serious injury da A DANGER HAZARD OF ELECTRIC SHOCK EXPLOSION OR ARC FLASH Only appropriately trained persons who are familiar with and understand the contents of this manual and all other pertinent product documentation and who have received safety training to recognize and avoid hazards involved are authorized to work on and with this product system Installation adjustment repair and maintenance must be performed by qualified personnel The system integrator is responsible for compliance with all local and national electrical code requi
10. APP FW e APPADDR BIN e APPDATA BIN MLDMSD FW e MSDADDR BIN e MSDDATA BIN New format 2 V3 08 To upgrade Firmware for Multi Loader from versions V3 08 following two files need to be copied to SD card e MLDAPP mld e MLDMSD mid Update procedure e Check that the SD card is inserted correctly in the e Insert the SD card in the SD card reader on the PC 4 Multi Loader 4 see page 13 Turn the Multi Loader on using button F see page 11 The SD card is recognized as an external storage device e Connect the Mini B connector to the Multi Loader Drag and drop the unzip files into the root directory and the type A connector to the PC see page 13 on the SD card by the PC 2 2 The Multi Loader is recognized as an external storage Wait until the files have loaded device Drag and drop the unzip files into the root directory on e Once the files have loaded successfully remove 3 the SD card by the PC 3 the SD card from the PC Wait until the files have loaded 4 Once the files have loaded successfully remove the 4 Insert the SD card in the Multi Loader USB cable from the PC and the Multi Loader Turn the Multi Loader off using button F see e Turn the Multi Loader on using button F see 5 page 11 5 page 11 Turn the Multi Loader on using button F see page 11 6 The Multi Loader launches the update automatically 6 The Multi Loader launches the update automatically
11. BBV48778 Multi Loader User manual VW3 A8 121 06 2014 Selyider www schneider electric com Contents Important information 4 Before you begin 5 Documentation structure 6 Setup procedure 7 Introduction 8 Receipt of the Multi Loader 9 Presentation 10 Description of the HMI 11 Description of the status Bar 12 Connecting the Multi Loader 13 Connection to aPC 13 Connection to a drive 14 Connection to the graphic terminal VW3A1101 15 Compatibility 15 Configuration transfers 16 Loading a configuration from a device and more 16 Transferring the configuration to a device and more use Quick Store 17 Multi Loader menus 18 Multi Loader main menu 18 Action Store configuration from Multi Loader to device 19 Action Load configuration from device to Multi Loader 20 Action Update device using Multi Loader 21 Quick Store mode 22 Supervision 23 Parameter settings Batteries 24 Parameter settings Diagnostics 25 Parameter settings Password 27 Parameter settings Display 28 Updating device application 29 Compatibility 29 Transferring the device update file 30 Updating the Multi Loader tool 31 Downloads 32 SoMove software 32 Device update file 32 Multi Loader updated file 32 Lists of faults codes 33 BBV48778 06 2014 3 Important information NOTICE Read these instructions carefully and look at the equip
12. d to load up to fifty devices a day and has a battery life of six days However this depends on the transfer time the size of the configuration files and other parameters associated with the settings for the Multi Loader and the connected devices It can configure ten drives in less than five minutes The Multi Loader can provide the power supply for certain devices if they are turned off during the transfer e The Multi Loader is also a firmware update tool The Password FW mode can be used to help protect against incorrect operation by means of a password See the Password FW menu on page 27 Duplicating or generating configuration files A Configuration duplicated E 1 Transfer to one device a SoMove 2 Transfer to several devices using Quick Store B Configuration generated A The device s configuration file is copied to the Multi Loader s SD card See the procedure on page 16 B The configuration file is generated by SoMove then transferred to the Multi Loader s SD card See the procedure on page 16 1 The user selects and then transfers the configuration file from the Multi Loader to the device See the procedure on page 17 Step 1 to 3 2 Once the initial transfer is complete the user can use Quick Store mode which allows the Multi Loader to load the same update file on several devices in succession See page 17 Step 1 to 4 Updating device firmware 1 Download the device s firmware nan E 1
13. d using the arrow keys and press ENT to start the transfer If no device is connected a message No device connected appears on the screen see page 25 Connect the Multi Loader to the next device then press the Quick Store key Flash FW Successful The firmware update file has been loaded successfully onto the The firmware update file has been loaded successfully onto the device disconnect the RJ45 cable from the device Pressing ENT returns the user to the Action 3 Config menu if no other devices require device disconnect the RJ45 cable from the updating device This action can be carried out as many times as necessary 30 BBV48778 06 2014 Updating the Multi Loader tool There are two methods for updating the Multi Loader The user connects the Multi Loader to the PC with the SD card in the Multi Loader and transfer the file for updated application device to the card SD The Multi Loader is then updated as soon as it is turned on Or The user copies the update file to the SD card with the SD card in the PC then inserts the SD card into the Multi Loader the Multi Loader is then updated as soon as it is turned on To download the files required for updating the Multi Loader tool see Downloads on page 32 OLD format S V3 08 To upgrade Firmware for Multi Loader from versions between V1 10 and V3 08 following six files need to be copied to SD card e MLD
14. e arrow keys and press ENT to start the transfer If no device is connected a message No device connected appears on the screen see page 25 The configuration has been transferred successfully from the Multi Loader disconnectthe RJ45 cable from the device Pressing ENT returns the user to the Action Config MLD gt Device menu or see STEP 4 for the Quick store e Connect the Multi Loader to the next device then press the Quick Store key Store Config Successful The configuration has been loaded successfully onto the second device remove the RJ45 cable from the device This action can be carried out as many times as necessary Note Storing a configuration to an ATV61 71 device with option board could generate a short time the display of Incorrect config CFF fault on the device during the operation BBV48778 06 2014 17 Multi Loader menus Multi Loader main menu On power up the Multi Loader Version x x menu is displayed on the screen The diagram below shows the various menus that can be accessed from the Multi Loader main menu Main menu Action accesses the following functions Load from Multi Loader to device Load from device to Multi Loader update software of device Main menu Device accesses the following information Device type Device version Main menu Parameters accesses Battery parameters Diagnostic parameters Password parame
15. etween Language 0 and 100 1 and 60 min Espanol Y Save language 28 BBV48778 06 2014 Updating device application Compatibility A DANGER UNINTENDED EQUIPMENT OPERATION e Read and understand this manual before installing or operating the Multi Loader e Any changes made to a device using the Multi Loader must be performed by qualified personnel Before you load a new product firmware read and understand the procedure transferring the device update file describes page 30 Ensure that you select the Firmware suitable for your application Failure to follow these instructions will result in death or serious injury The Multi Loader can be used to update a device s firmware fw file via the RJ45 cable provided in the box The table below shows the devices that are compatible with the Multi Loader It shows which type of file can be transferred depending on the state of the device BE Graphic terminal VW3A1101 x ATV303 o ATV12 o ATV32 o Lexium 32 o Lexium 32S o e Device compatible with the Multi Loader tool Note 1 The update file must be compatible with the device Any incompatibility will prompt a message Wrong reference Fault and the transfer operation will not be done See table on page 25 Note 2 When updating device firmware you must ensure that all downloaded files are copied to the Multi Loader s SD card fw file and e
16. ge is too low The Multi Loader will Replace the batteries immediately No more Low battery turn off transfers can be made Check the RJ45 cable and both of its N Incomplete or incorrect transfer to the device conrectors Mel sure ine coungelouils config fault P secure for the duration of the transfer Restart the transfer operation Bad transfer to the device the configuration file Check that the configuration file is compatible Wrong reference E E AR e Fault selected is not compatible with the destination with the device to be configured device BBV48778 06 2014 25 Multi Loader menus Parameter settings Diagnostics Load Incomplete or incorrect transfer from the Multi Check the RJ45 cable and both of its config fault Loader to the device connectors Restart the transfer operation Check the RJ45 cable and both of its Flash FW incomplete onincorrect device update connectors Make sure the connection is Fault p P secure for the duration of the transfer Restart the transfer operation Check the RJ45 cable and both of its No device The device is not connected or is incorrectly connectors Make sure the connection is connected connected secure for the duration of the transfer Connect the RJ45 cable No file No configuration file is selected o tenei e Follow the procedure for loading configuration selected There is no file present on the SD card A files described on page 16
17. gram below shows the Parameters Display menu accessible from Main menu Parameters Display Contrast This menu is used to set the display screen contrast Display Backlight This menu is used to set the display screen backlight Display Sleep mode This menu is used to set the Multi Loader s sleep mode Display Language This menu accesses the language selection for the Multi Loader interface J Parameters Display es s s o s Display Display 4 Display Display gt Contrast Backlight gt Sleep mode gt Language z J gt y Y m ee _ ENT Esc Set contrast Set backlight Set sleep mode Language ut 50 ON 05 min English DE o 3 De De x y e z S Set contrast Set backlight Set sleep mode _ Language gt NN OFF NN min Ara 9 0 9 DO Saves the Saves the Saves the sleep ENT y Esc contrast value backlight value mode value ee DS ak Yy ae Press and hold the Press and hold the Y Language S up or down arrow up or down arrow Italiano k define the i ey to key to define the DO contrast value more sleep mode value Z y quickly more quickly O Ese Deutch E De y Value between Value b
18. gt Device This menu accesses the transfer function for loading configurations from the Multi Loader to the device Main oi Action Config menu gt MLD gt Device No device connected No SD card Fault Page 22 A y 6 evice connected SD card readable MLD gt Device Filename1 gt MLD gt Device Filename2 MLD gt Device FilenameN o The file is saved for Quick Store mode Transfer in progress Y FilenameX Quick gt gt gt lt 0 Store Y FilenameX gt gt gt gt gt gt gt gt Y FilenameX gt gt gt gt gt gt gt gt gt gt gt Y Transfer complete Two types of error message Store config Successful Yes Quick Store No Incomplete or incorrect transfer Incorrect configuration file for this device Y Y Store config fault Wrong reference fault mode BBV48778 06 2014 19 Multi Loader menus Action Load configuration from device to Multi Loader The diagram below shows the Action Config Device gt MLD menu accessible from Main menu Action Action Config Device gt MLD This menu accesses the transfer function for loading configurati
19. gt Device or Action Flash Firmware menus sath EA ey i an Mo connected ___ a ie Fo selected Yes Configuration file s Two file types la E Yes SD card No gt gt readable Yes No No device connected SD card Fault FW file y Page 21 pan Y No file selected e y Exit Quick Store mode Note 1 If the Multi Loader is already loading a file the Quick Store key is inactive Note 2 Quick Store mode can only be used after an initial transfer to a device has been completed 1 Files can only be transferred between devices with the same reference 22 BBV48778 06 2014 Multi Loader menus Supervision The diagram below shows the device main menu accessible from Main menu Device This supervisory menu is used to check the reference and version of the device connected to the Multi Loader Device Type This menu accesses the reference of the connected device Device SW version This menu accesses the software version of the connected device Main menu e Device je Device m gt Type Device lt connected Range ATVXXXXXXXX No Device SW Version 4 e Device connected es Y SW Version VXX XX Y No device connected En
20. ish and French e 1x impact resistant cover Available as an option e Multi Loader Cordset VW3A8126 not compatible for ATV32 and LXM32 BBV48778 06 2014 9 Receipt of the Multi Loader 65 mm 2 6 In Schneider 181 51 mm 7 26 In Figure 1 Presentation 27 4 mm 1 09 In Weight 250 grams including batteries Data storage One SD card is supplied with the Multi Loader Any standard SD card is compatible with the tool not SDHC card except the model delivered with the Multi Loader Language All menus are in English French German Italian Spanish Chinese and Japanese Power supplies Two options are available for powering the Multi Loader 1 With internal power supply 4x LR6 AA alkaline batteries batteries included NiMh rechargeable batteries batteries and charger not included 2 With external power supply e USB type A to Mini B cable direct on the PC power supply Battery life Depending on the type of batteries used the Multi Loader can transfer up to 300 configuration files Power save feature To prolong battery life a standby function is activated within a programmable time delay the Multi Loader is reactivated by pressing the ON OFF button See the display parameters menu on page 28 Connection to a powered up PC or device can also help conserve battery power as the power supply from the connected device ta
21. isplays Main menu Action Select the Action Config Device gt MLD menu using the arrow keys and press ENT Device gt MLD LoadFromDevice appears on the screen Press ENT until the transfer starts Load Config Successful The configuration has been loaded successfully onto the Multi Loader disconnect the RJ45 cable from the device The device configuration file file cfg is now loaded onto the Multi Loader s SD card Pressing ENT returns the user to the Action Config menu e For another loading configuration into the Multi Loader repeat the step 1 and step 2 Ee Note 1 The file will be stored in a folder folder name is the first 5 letters of the device ID kept in a directory called LoadFrmDev located at root Ee Note 2 Loading a configuration from an ATV61 71 device with option board could generate a short time the display of Incorrect config CFF fault on the device during the operation 16 BBV48778 06 2014 Configuration transfers Transferring the configuration to a device and more use Quick Store A DANGER UNINTENDED EQUIPMENT OPERATION e Read and understand this manual before installing or operating the Multi Loader e Any changes made to a device using the Multi Loader must be performed by qualified personnel e Read and understand the device manuals before you load or duplicate the Configuration from one device to another device e Ensure that you select the
22. kes over from the batteries BBV48778 06 2014 Receipt of the Multi Loader Description of the HMI Figure 2 A Mini B USB connector The connection between the Multi Loader USB Mini B type and the PC USB type A is via a 1 m 3 28 feet USB type A to Mini B cable B RJ 45 connector The connection between the Multi Loader and the device is via a RJ45 cable to load and transfer configuration files or updated application C RJ11 connector with label cover This connector is reserved for Schneider Electric product support D SD card slot The SD card receives and stores the files One SD card is supplied with the Multi Loader Battery compartment The Multi Loader can take normal batteries or rechargeable batteries ON OFF button Press for 2 seconds to turn the tool on or off G Quick Store key Press this key to transfer data from the Multi Loader to the device after an initial transfer H Screen The screen comprises 2 lines of 16 characters see page 12 l ESC key Returns to the previous screen J ENT key Confirms the parameter selection or cancels messages K Up arrow key fy For menu navigation L Down arrow key Sy For menu navigation BBV48778 06 2014 11 Receipt of the Multi Loader Description of the status Bar The drawings below show names and functions of main parts
23. ly Main gt Action Flash x menu Firmware Device No device em connected connected pe Yes Yes Update authorized No Press and hold the y up or down arrow Enter password Re key to define the 000 password more quickly t gt Enter password gt NNN Value between En 000 and 999 en 1 Default value 000 password Yes Y Update authorized SD card No SD card En readable Fault Yes i a 3 p e Flash FW Flash FW Glock oe E Filename 1 Filename 2 FilenameN oe Je 2 y Quick q gt Replace Store Firmware The file is Y saved for Filenamex Quick Store 3 mode N In FilenameX gt gt gt gt gt gt gt gt Transfer in progress Py FilenameX gt gt gt gt gt gt gt gt gt gt gt Transfer complete Yes Flash FW Flash FW Page 22 Successful Fault 0X en En 7 an Yes Quick Store No mode BBV48778 06 2014 21 Multi Loader menus Quick Store mode This mode is used to transfer the latest configuration file page 17 or latest device firmware updated file page 30 1 The diagram below shows the Quick Store mode which can be accessed after using either ofthe Action Config MLD
24. ment to become familiar with the device before trying to install operate or maintain it The following special messages may appear throughout this documentation or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure The addition of this symbol to a Danger or Warning safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided can result in death serious injury or equipment damage A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided can result in injury or equipment damage NOTICE NOTICE indicates a potentially hazardous situation which if not avoided can result in equipment damage PLEASE NOTE The word drive as used in this manual refers to the controller portion of the adjustable speed drive as defined by NEC Electrical equipment should be installed operated serviced and maintained only by qualified personnel No respon
25. n page 16 and Configuration transfers on page 17 If the configuration file is generated by SoMove software it must then be transferred to the Multi Loader s SD card See Downloads on page 32 and Connection to a PC above BBV48778 06 2014 13 Connecting the Multi Loader Connection to a drive There are three ways of transferring configuration files The drive is in its packaging When the drive is off the Multi Loader is powered Note When the drive is in its box the Multi Loader Cordset option can be used for quicker and easier in box connection no locking tab on the connector thus speeding up the transfer and keeping the packaging intact The drive is mounted wired and powered up or the drive is power on When the drive is on the Multi Loader is powered by the drive via the RJ45 cable A A DANGER HAZARD OF ELECTRIC SHOCK EXPLOSION OR ARC FLASH EXPOSURE TO ENERGIZED PARTS e Adhere to NFPA 70E guidelines when using the Multi Loader e The Multi Loader is to be used only by qualified personnel as defined in NFPA 70E e Read and understand the manuals for the applicative drive before accessing the communication port of the drive e Ensure that the RJ45 cable is not damaged Failure to follow these instructions will result in death or serious injury Schneider Electric recommends that all power from the drive and enclosures housing the drive is disconnected before performing this pr
26. ocedure If you choose not to follow this recommendation you must adhere to NFPA 70E guidelines 1 Remove all power from the drive and all enclosures housing the drive and wait 15 minutes to allow the DC bus of the drive to discharge 2 Insert the Multi Loader s communication cable into the drive s RJ45 communication port Refer to the drive s installation manual for more information about how to perform this task 3 Install and close all covers and doors before applying power to the drive The drive must be powered on before performing an upload or download 4 Perform the desired transfer 5 Upon completing the transfer remove all power from the drive and the enclosures housing the drive and wait 15 minutes to allow the DC bus of the drive to discharge 6 Remove the Multi Loader communication cable from the drive 7 Install and close all covers and doors before reapplying power to the drive 8 Confirm that the correct program is in the drive 14 BBV48778 06 2014 Connecting the Multi Loader Connection to the graphic terminal VW3A1101 The Multi Loader can be connected to the graphic terminal via its RJ45 female female adapter VW3A1105 This adapter is needed for updating the graphic terminal Configuration transfers Compatibility The table below shows the devices that are compatible with the Multi Loader It shows which type of file can be transferred depending on the state of the device The Mul
27. ons from the device to the Multi Loader Action Config Device gt MLD Device connected SD card readable Device gt MLD LoadFromDevice No device connected SD card Fault amp Are there more 99 files in the card Replace LoadFrmDxx 0 LoadFrmDxx lt lt lt lt Y Transfer in progress LoadFrmDxx BEGGS Y LoadFrmDxx See Transfer complete Load config Successful Load config fault gt gt Note1 The file will be stored in a folder folder name is the first 5 letters of the device ID kept in a directory called LoadFrmDev located at root Note 2 The maximun number of configurations for each range are 99 20 BBV48778 06 2014 Multi Loader menus Action Update device using Multi Loader The diagram below shows the Action Flash Firmware menu accessible from Main menu Action Action Flash Firmware This menu accesses the transfer function for loading the software update file onto the device It is possible to protect the firmware update transfer See the Parameters Password FW menu on page 27 An RJ45 cable is required for updating the device firmware see the compatibility table on page 29 If a device is updated without being turned on the Multi Loader provides the power supp
28. ram erase detected FAULT 0x12 Path too long FAULT 0x24 0x34 Flash FW File in a wrong format Drives Flash FW Wrong program download detected FAULT 0x13 FAULT 0x25 0x35 Flash FW File in a wrong format Graphic keypad FAULT 0x14 Specific graphic keypad Specific motor control FW Flash FW Wrong file detected Flash FW Wrong download detected FAULT 0x9a FAULT Ox4a Flash FW Fonts file download failed Flash FW Flashing Motor Control is not allowed when FAULT 0x9b FAULT 0x40 the drive is Power On Flash FW Labels file download failed Flash FW Wrong communication detected FAULT 0x9c FAULT 0x41 Flash FW Bitmaps file download failed Flash FW Inquiry device failed FAULT 0x9d FAULT 0x42 Flash FW Internal Error Flash FW Selection device failed FAULT 0x91 FAULT 0x43 Flash FW Wrong file detected Flash FW Inquiry of clock modes failed FAULT 0x92 FAULT 0x44 Flash FW Internal Error2 Flash FW Selection of clock modes failed FAULT 0x93 Unable to open the file FAULT 0x45 Flash FW Wrong communication detected Flash FW Inquiry of write line size failed FAULT 0x94 FAULT 0x46 Flash FW Syntax error of the configuration file Flash FW Wrong communication detected baud FAULT 0x95 FAULT 0x47 rate Flash FW Wrong file detected Flash FW End setting data failed FAULT 0x96 FAULT 0x48 Flash FW Wrong file detected Flash FW Wrong memory write detected FAULT 0x97 FAULT 0x49 Flash FW Wrong configuration format file detec
29. rements as well as all other applicable regulations with respect to grounding of all equipment Many components of the product including the printed circuit boards operate with mains voltage Do not touch Use only electrically insulated tools Do not touch unshielded components or terminals with voltage present Motors can generate voltage when the shaft is rotated Prior to performing any type of work on the product system block the motor shaft to prevent rotation e AC voltage can couple voltage to unused conductors in the motor cable Insulate both ends of unused conductors of the motor cable Do not short across the DC bus terminals or the DC bus capacitors or the braking resistor terminals e Before performing work on the product system Disconnect all power including external control power that may be present Place a Do Not Turn On label on all power switches Lock all power switches in the open position Wait 15 minutes to allow the DC bus capacitors to discharge The DC bus LED is not an indicator of the absence of DC bus voltage that can exceed 800 Vdc Measure the voltage on the DC bus between the DC bus terminals using a properly rated voltmeter to verify that the voltage is lt 42 Vdc If the DC bus capacitors do not discharge properly contact your local Schneider Electric representative Install and close all covers before applying voltage Failure to follow these instructions will result in death or
30. rer using the same copy paste actions as any standard external storage medium Note The PC must be on and operational before connecting the Multi Loader to avoid an incorrect start up of the PC The SD card must not be removed when the Multi Loader is on and a transfer is in progress Otherwise data on the SD card may be lost The file name can have 32 characters and the special characters are forbidden e The following priority rules come into play when the Multi Loader is connected to a PC If no transfer is in progress between the Multi Loader and the drive the connection to the drive is ignored and the Multi Loader is detected by the PC If a transfer is in progress between the Multi Loader and the drive the user has to wait until the transfer is complete The Multi Loader should be reconnect to the pc for can be detected If the Multi Loader is connected to the PC without a SD card it is necessary to disconnect the Multi Loader before inserting SD card to be recognized by the PC as an external storage device If the Multi Loader is connected to the PC without a SD card it is power supply by the PC Insert the SD card to be recognized by the Multi Loader you can transfer configuration file Source of configuration files There are two ways of managing configuration files If a device s configuration is to be duplicated it is copied to another device via the Multi Loader See Loading a configuration from device o
31. ted FAULT 0x98 Flash FW No keypad connected FAULT 0x99 Wrong update labels of keypad detected BBV48778 06 2014 Lists of faults codes A DANGER UNINTENDED EQUIPMENT OPERATION DUE TO TRANSFER INTERRUPTION If an interruption occurs during the transfer of configuration to the device e Identify and correct the cause of interruption e Repeat the transfer Failure to follow these instructions will result in death or serious injury Specific Lexium 32 Flash FW Wrong compatilibity detected FAULT 0x81 Flash FW Product not available for upgrade FAULT 0x82 Flash FW Wrong Flash mode set FAULT 0x83 Flash FW Wrong downloader upgrade application FAULT 0x84 Flash FW Wrong program erase detected FAULT 0x85 Flash FW Wrong program download detected FAULT 0x86 Flash FW Wrong exit update detected FAULT 0x87 Flash FW Wrong exit verification detected FAULT 0x88 BBV48778 06 2014 Notes BBV48778 06 2014 35 36 BBV48778 06 2014 Multi_Loader_user_manual_EN_BBV48778_ 05 BBV48778 06 2014
32. ters Display parameters Main menu About MLD accesses Multi Loader version information The Quick Store key G see page 11 allows the user to transfer the most recent configuration file or update the device see page 22 ON Page 22 Quick Store eer Aa Multiloader Version X X 2s af 2 it Main menu Main menu Main menu Main menu fo ne Action D Device a Parameters DO About MLD T e 0 1 D y E SIE Action Config P 19 Page 23 Parameters Build AB CD MLD gt Device 6 age 19 o Battery A Page 24 dd mm yy hh mm A Bi Ke ae A ENT ee Ly a oO Kur T Esc 2 Y Esc Action Config Parameters Device gt MID N Page 20 Diagnostic ra Page 25 A E ENT I IE A Du UDS 2 r 2 Y Action Flash Banks Firmware m M T Page 21 Password FW LE ug Page 27 a ent En vV OA Y en g Y Parameters Display Page 28 A y A N Ee Note Quick Store mode is disabled when the Multi Loader is loading files 18 BBV48778 06 2014 Multi Loader menus Action Store configuration from Multi Loader to device The diagram below shows the Action Config MLD gt Device menu accessible from Main menu Action Action Config MLD
33. ti Loader can be used to Transfer configuration cfg files via the RJ45 cable supplied with the Multi Loader ESP on e ATV303 o ATV12 ATV212 ATV32 ATV312 LXM 32 LXM 32S ATV31 ATV71 ATV61 e Device compatible with the Multi Loader tool Note When transferring files devices must have the same reference Any incompatibility will prompt an message Wrong reference Fault and the transfer operation will not be done See the table of detected fault on page 25 BBV48778 06 2014 15 Configuration transfers Loading a configuration from a device and more This procedure allows the user to retrieve a configuration file file cfg from a device and load it onto the Multi Loader s SD card E gt U e Action e Action Config MLD gt Device v gt Y Action Config Device gt MID 9 Device gt MID LoadFrmDxx y 69 Are there more 99 files on the card am Yes No Y Replace LoadFrmDxx A 10 LoadFrmDxx lt lt lt lt Y LoadFrmDxx lt lt lt lt lt lt lt lt y LoadFrmDxx lt lt lt lt lt lt lt lt lt lt lt Turn the Multi Loader on using the ON OFF button F see page 11 Connect the Multi Loader to the device using the RJ45 cable see page 14 Press ENT when the screen d
34. xecutable file Note 3 Ensure that you update the product device label and the keypad label after updating device application BBV48778 06 2014 29 Procedure Transferring the device update file This procedure describes how to select the device update file The user can then use Quick Store mode for the rest of the operation see page 22 The user must already have Downloaded the update file from www schneider electric com see page 31 AND Transferred the file to the Multi Loader see page 13 Connection to a PC ML Action en a E Action Config gt I MLD gt Device Y Action Flash Firmware Flash FW Successful Device 1 2 Flash FW Flash FW lt Flash FW Flash FW Filename 1 Filename 2 Filename N Successful Device 2 wa Ta e l Flash FW Successful Device n Y FilenameX gt gt gt gt A y A FilenameX gt gt gt gt gt gt gt gt 3 Y 3 FilenameX em gt gt gt gt gt gt gt gt gt gt gt ud Flash FW Successful gt Turn the Multi Loader on using the ON OFF button F see page 11 e Connect the Multi Loader to the device using the RJ45 cable see page 14 Press ENT when the screen displays Main menu Action Select the Action Flash Firmware menu using the arrow keys and press ENT Select the file to be transferre

Multi-Loader menus - Schneider Electric

Contents

Download Pdf Manuals

Related Search

Related Contents