Winner4 OSD Manual - 2 Geek Tech Support Services
Contents
1. Vandal Proof Camera Strong points High Resolution IP 66 Certified Vandal resistant FC rai Full 3 axis bracket built in RoHS j compliant CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance This equipment has been tested and found to comply with limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which cas2. HLC Enable a user to select a mask colour of highlight area from a picture HLC SETUP P MASK COLOR livin Press SET to Return 4GO e Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen optimize the installation angle for the best HLC performance e When dark the HLC is only activated when a bright light exceeding a specific size e The HLC is not activated in day light or when bright light is not present at night COLOUR DOME CAMERA 8 User s Manual This function reduces the background noise in a low luminance environment You can display pictures in colour or black and white 1 When the SUP menu screen is displayed select SSNR by using the Function 1 When the SETUP menu screen is displayed select DAY NIGHT by using the Setup switch so that the arrow indicates SSNR Function Setup switch so that the arrow indicates DAY NIGHT Pm 5 SSNR 2 Select a desired mode using the Function Setup switch OFF Deactivates SSNR Noise is not reduced ON Activates SSNR so that noise is reduced 2 Select a desired mode using the Function Setup switch according to the picture display you want 3 Set the SSNR mode to ON and press the Function Setup switch Then you can pany adjust the noise reduction level COLOUR The picture is always displayed in colour i B W The picture is always displayed in black and E ESETE
3. OFF no title will be displayed on the monitor screen gt 1 CAM TITLE even if you enter one e Only English is available in this mode 3 Press the Function Setup switch 4 Use the Function Setup switch to move to a desired letter and select the letter by pressing the Function Setup switch Repeat this to enter multiple letters You can enter up to 15 letters e f you move the cursor to CLR and press the Function Setup switch all the letters are deleted To edit a letter change the cursor to the bottom left arrow and press the Function Setup switch Move the cursor over the letter to be edited move the cursor to the letter to be inserted and then press the Function Setup switch 5 Enter a title move the cursor to POS and press the Function Setup switch The entered title FRONT DOOR _ f appears on the screen Select the position to display the title on the screen by using the Function Setup switch and press When the position is determined select END and press the Function Setup switch to return to the SPECIAL menu Operating Your Camera SYNC In areas where the supply is at 60Hz you can synchronize the output phase of multiple cameras SYNC using the power synchronization function Line er oi 2n Lock without using a synchronization signal Mode OFF generator INT Internal Synchronization Type Press SET to Return L L Power Synchronization Type Line lock e Pre
4. to less than 46 level KO a ee ers COLOUR DOME CAMERA 16 User s Manual Operating Your Camera COMM ADJ Communication Adjustment This function sets up the camera communication status when controlling the camera through an external control device When the SPECIAL menu screen is displayed press the Function Setup switch so that the arrow indicates COMM ADJ 2 Set up the mode using the Function Setup switch COMMUNICATION SETUP 2 BAUD RAET 3 UART MODE 4 RET PKT 5 DISP CAM ID Press SET to Return CAM ID Determines the camera s identification number between 0 and 255 BAUD RATE You can select 2400 4800 9600 19200 38400 57600 bps UART MODE You can select NONE EVEN or ODD for the parity bits RET PKT Determines whether to send a command back to the controller device when a communication control command is sent to the camera DISP CAM ID Display camera title on top left corner of the screen Initial value of communication adjustment Item BAUD RATE UART MODE PET PKT Initial value 1 9600 8 NONE 1 ENABLE LANGUAGE You can select the menu language according to your requirements RESET Resets the camera settings to the factory defaults The communication status and language are not reset RETURN Select this to save the SPECIAL menu settings and return to the MAIN SETUP menu EXIT Press the Function Setup switch in the EXIT menu to save t
5. P menu The screen flickers continually X Check that direction of camera turns toward the Sun RS 485 communication fails X Check the polarity between RS 485 Control Port and RS 485 cable 485 Control Board Connection Port RS 485 Control Port CONNECTION TERMINAL TRX 485 CONNECTION TERMINAL TRX 485 X Check the RS 485 Communication establishment initial value RS 485 Communication establishment initial value Item BAUD RATE UART MODE RET PKT Initial value 1 9600 8NONE1 ENABLE X We recommend that you make ground connect between camera and controller in order to maintain safety communication control COLOUR DOME CAMERA 18 User s Manual
6. e the user will be required to correct the interference at his own expense Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment To prevent electric shock and risk of fire hazards X Do NOT use power sources other than that specified X Do NOT expose this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes COLOUR DOME CAMERA 2 User s Manual Q Getting Started o Quick installation Open the box and check the contents View angle adjustment lever Rotate 360 Focus 5 Tilt 90 adjustment E lever w Pan 360 ps pews ae oma 2UASSY SCREW UPENCHOR TAPPING 3UOPENING 40LWRENCH TOOL 5U TEMPLATE 60RUBBER PAD Connecting the power and video 1 Open the dome 2 You can change the pipe hole Extra Video output Video output 1 2 y D C COLOUR DOME CAMERA 3 User s Manual gt Use the Function Switch switch on the main body of the camera Function Setup switch 1 Press the Function Setup switch e Main setup menu is displayed on the monitor screen Select the function by 1 LENS DG hange the status by moving up or down direction noving right or left direction of function setup switch of function setup switch 2 Select a desired function using the Function Setup switch e Place the cursor over a desired it
7. em 3 Set up a selected item by using the Function Setup switch 4 To finish the setting select EXIT and press the Function Setup switch e An item with the icon also has sub menus To select a sub menu select an item with the icon and press the Function Setup switch e An item with the icon is unavailable due to function settings Using this function you can control screen brightness 1 When the SETUP menu screen is displayed select LENS by using the Function Setup switch so that the arrow indicates LENS gt 1 LENS DG DC Select Auto Iris Lens e When DC is selected you can control screen brightness The range of brightness control is between 1 and 70 Adjust the brightness appropriately for optimal screen brightness Press SET to Return LENS P BRIGHTNESS mm umm 25 p gt 2 EXPOSURE lt 1 1 When the SETUP menu screen is displayed select EXPOSURE by using the Function Setup switch so that the arrow indicates EXPOSURE ec HIGH 3 SENS UP OFF 2 Select a desired mode using the Function Setup switch 4 RETURN EXPOSURE SETUP SHUTTER Because of using built in dc lens shutter speed is fixed at 1 60 1 50 basically A FLK Select this when you experience picture flicker which can happen when there is a clash with the frequency of the installed lighting Operating Your Camera AGC AUTO GAIN CONTROL The higher the gain level the bright
8. enu screen is displayed select IMAGE ADJ by using the Function Setup switch so that the arrow indicates IMAGE ADJ p gt 7 IMAGE ADJ 2 Select a desired mode using the Function Setup switch 11 gt 1 V REV V REV You can flip the picture vertically on the y screen D ZOOM H REV You can flip the picture horizontally on gt LEVEL the screen D ZOOM You can use a digital zoom of x2 x10 _ SHARPNESS As you increase this value the picture outline becomes stronger and clearer Adjust this value appropriately depending on the sharpness of the picture Press SET to Return RETURN Select this to save the settings for the IMAGE ADJ menu and to return to the SETUP menu e When the V REV or H REV mode is enabled the text on the screen does not flip e f you increase the SHARPNESS level too high the picture may become distorted or noise may appear 1 When the SETUP menu screen is displayed select SPECIAL by using the Function Setup switch so that the arrow indicates SPECIAL Pm SSPECIAL lt 1 2 Select a desired mode using the Function Setup switch p gt 1 CAM TITLE CAMTITLE If you enter a title the title will appear on the monitor If the SPECIAL menu screen is displayed use the Function Setup switch so that the arrow indicates CAM TITLE 2 Set it to ON by using the Function Setup switch 13 e When the CAM TITLE menu is
9. er the screen but the higher the noise OFF Deactivates the AGC function LOW Allows automatic gain control from 5 3dB to 30cB HIGH Allows automatic gain control from 5 3dB to 42dB SENS UP When it is night or dark the camera automatically detects the light level and maintains a clear picture if this mode is activated OFF Deactivates the SENS UP function AUTO Activates the SENS UP function LIMIT gt AUTO X2 Press SET to Return RETURN Select this to save the changes in the EXPOSURE menu and return to the SETUP menu e f you press the Function Setup switch in AUTO mode You can adjust brightness by increasing or decreasing the shutter speed x2 x256 e Note that the higher the zoom level the brighter the screen but the more likely it is that an after image will appear e Although Noise Spots and Whitish symptoms may occur in SENS UP operation when the zoom level is increased this is normal White Balance White Bal Use the White Balance function to adjust the screen colour 1 When the SETUP menu screen is displayed select White Bal by using the Function Setup switch so that the arrow indicates White Bal 2 Select a desired mode using the Function Setup switch COLOUR DOME CAMERA 59 User s Manual MAIN SETUP 1 LENS Deal 2 EXPOSURE 4 gt 3 WHITE BAL ATW 4 BACKLIGHT OFF gt Select one of the following 5 modes as appropriate f
10. he current settings and exit the MAIN SETUP menu COLOUR DOME CAMERA 17 User s Manual Q Troubleshooting Refer to the following table if you are experiencing trouble with your camera Contact an authorized technician if the table does not provide you with a solution to the trouble Nothing appears on the screen X Check that the power cord and line connection between the camera and monitor are connected properly X Check that you have properly connected VIDEO cable to the camera VIDEO output jack The image on the screen is dim X Is lens stained with dirt Clean your lens with soft clean cloth X Set the monitor to proper condition X If the camera is exposed to too strong light change the camera position The image on the screen is dark X Adjust the contrast feature of the monitor X Ifyou have an intermediate device set the 750 Hi z properly The camera is not working properly and the surface of the camera is hot X Check that you have properly connected the camera to an appropriate power source The DAY NIGHT menu does not work K Check that AGC of EXPOSURE SETUP menu is OFF The SENS UP function does not work X Check that AGC of EXPOSURE SETUP menu is OFF X Check that SHUTTER of EXPOSURE SETUP menu is A FLK The Motion Detection function does not work X Check that MOTION DEF of SPECIAL SETUP menu is OFF Colour is not correct K Check the setting of WHITE BAL SETU
11. ike conventional cameras by adopting a proprietary W 4 DSP chip 1 When the SETUP menu screen is displayed select BACKLIGHT by using the LENS sets DG Function Setup switch so that the arrow gt EXPOSURE M indicates BACKLIGHT l l 3 WHITE BAL ATW 2 Select a desired mode using the Function a BACKLIGHT OFF Setup switch depending on the camera 5 SSNR ON purpose BLC Enables a user to directly select a desired area from a picture and to view the area more clearly iii e Select BLC to adjust the area to be enhanced and enhancement level Press SET to Return HLC High Light Compensation If the scene contains extremely brightly light areas such as car headlights the light can mask out much of the on screen detail Use Samsung Techwin s HLC feature to remove these exceptionally brightly light areas to allow detail such as car number plates to become visible DAY In normal daylight conditions the HLC is not active NIGHT If a bright light exceeding a specific size is present on screen it will be removed masked out to display the vehicle number plates clearly COLOUR DOME CAMERA 7 User s Manual OFF Not being used 3 Select a desired mode using the Left and Right buttons and press the SET button BLC SETUP Select BLC to adjust the area to be enhanced and PTOP y enhancement level LERT LEVEL Press SET to Return
12. or your purpose ATW Select this when the colour temperature is between 1 800 K and 10 500 K INDOOR Select this when the colour temperature is between 4 500 K and 8 500 K OUTDOOR Select this when the colour temperature is between 1 800 K and 10 500 K sodium light inclusion AWCW SET To find the optimal setting for the current luminance environment in this mode set the point the camera towards a sheet of white paper and press the Function Setup switch If the environment changes readjust it MANUAL Select this to fine tune White Balance manually Set White Balance first by using the ATW or AWC mode After that switch to PRED ween 100 MANUAL mode fine tune the White Balance and then press the Function Setup switch ee e White Balance may not work properly under the following conditions In this case select the AWC mode When the colour temperature of theenvironment surrounding the subject is out of the control range e g clear sky or sunset 2 When the ambient illumination of the subject is dim 3 If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically the White Balance operation may become unstable COLOUR DOME CAMERA 6 User s Manual Operating Your Camera BACKLIGHT This camera is designed so that it delivers a distinctive subject and background at the same time even when the subject is in backlight unl
13. ss the Function Setup switch e You can select a desired phase from 0 to 359 when select phase e You can decide the synchronization between luminance and signal when select the Mode to TRACE e When using AC power at 60Hz frequency you can use the L L type synchronization e When the power is DC 12V the SYNC menu is fixed to the INT mode MOTION DET You can monitor activity more efficiently because a signal is generated by the camera whenever motion is detected MOTION DET SENSITIVITY AREAL ADU PWD When the SPECIAL menu screen is displayed press the Function Setup switch so that the arrow indicates MOTION DET 2 Set up the mode using the Function Setup switch SENSITIVITY You can select up to 8 MD areas When SENSITIVITY number is high motion detection sensitivity is increased to recognize even small movement AREA MODE Determines whether to use the MD area selected in SENSITIVITY SEL POS Determines which of the 4 vertices of each MD area is to be used YPOS Determines the coordinate of the vertical axis for SEL POS XPOS Determines the coordinate of the horizontal axis for SEL POS FILL SET Fills in a selected MD area Fills in a selected MD area The of filling is sequentially selected as brown orange blue cyan yellowish green yellow and red RETURN Select this to save the MOTION DET menu settings and return to the SPECIAL men
14. u COLOUR DOME CAMERA 15 User s Manual e MD areas show only MOTION DET menu Therefore MD areas don t display on the monitor screen e When motion is detected MOTION DETECTION expression is displayed on the screen PRIVACY Hide an area you want to hide on the screen PRIVACY When the SPECIAL menu screen is displayed P 2L AREA WDE ON UPWDY FE press the Function Setup switch so that the TEMES osm 0 arrow indicates PRIVACY ie 2 Setup the mode using the Function Setup switch AREA SEL You can select up to 8 PRIVACY areas AREA SETUP AREA MODE Determines whether to use the area gt rto J selected in the AREA SEL the size rr and position of the area Press SET to Return MASK Determine area colour You can select Gray Green Red Blue Black White TRANSP Determine the transparency of the selected area adjust the level between 0 and 3 RETURN Select this to save the PRIVACY menu settings and return to the SPECIAL menu DIS Digital Image Stabilizer This function mitigates any picture movement due to external factors such as wind e t is possible that the quality of resolution may decrease as the DIS function uses the digital zoom e DIS doesn t operate when background illumination is too low e DIS doesn t operate when object pattern is monotonic as like sky or white wall e If DIS is enabled the digital zoom is not configured
15. white Please press Function Setup switch to ae on turn on or off the burst signal on B W mode AUTO The mode is switched to Colour in anormal f Press set to Return environment but switches to B W mode _ when ambient illumination is low To set up the switching time or speed for AUTO mode press the Function Setup switch gt DWELL TIME 10 SEC e You cannot set the SSNR to ON or OFF when the AGC mode of the EXPOSURE DWELLTIME You can select the duration time about MA 3 menu is OFF changing the day night mode Press SET to Return e When adjusting the noise reduction level in the SSNR mode remember that the X 5s 7s 10s 15s 20s 30s 40s 60s higher the level set the more the noise level will be reduced as will the brightness ie er srk image DURATION You can select the brightness switching point between Fast and Slow Press SET to Return AUTO SETUP Colour X BW BW Colour Fast 25lux 4 lux Slow 0 8 lux 6 lux Light levels are often site dependant e You cannot control the DAY NIGHT menu when AGC in the EXPOSURE menu is OFF At this time the exchange between DAY mode and NIGHT mode operates as like selecting COLOUR mode e The OSD key does not work for 3 seconds when switching to Colour or B W to ensure stable camera operation e The camera may focus less well under infrared illumination than under normal illumination 1 When the SETUP m
Download Pdf Manuals
Related Search