Voice Dialer - Seco-Larm
Contents
1. 000 and press the PROG button once PASSWORD will flash on the LCD 2 Press the ARM DISARM button to accept 3 Enter a new PIN number 3 6 digits followed by the ARM DISARM button to confirm 4 Press the DOWN or UP button to select other setup categories or press the PROG button until the programming icons disappear to exit the setup mode Note If the PIN number is forgotten press and hold the PROG button and use a pen or paper clip to press the RESET button located near the battery receptacle cover on the back of the unit and release The unit will return to the factory preset PIN number 000 All other user programmed settings except the date and time will be retained Setting Emergency Phone Numbers 1 Enter the PIN number and press the PROG button twice or until MEMORY flashes on the LCD screen 2 Press the ARM DISARM button to accept 3 Press the DOWN or UP button to select one of the number locations 1 5 Note The 5 number locations represent the order in which the numbers will be dialed in the case of an alarm 4 Enter the number to store including any area codes or dialing prefixes if needed up to 32 digits although only the last 16 digits can be shown on the LCD display using the keypad followed by the ARM DISARM button to accept and store the number Note If needed add a 4 second pause before a PBX extension number by pressing and holding the DEL2. HOME will appear on the Numeric Keypad LCD screen Microphone 2 After 60 seconds another chime indicates that the voice dialer is now in the Home mode 3 When a sensor is activated the voice dialer will chime twice LINE Jack 4 Ifthe panic button is pressed the voice dialer will sound a 30 second alarm and start the ree dialing sequence to the programmed emergency numbers Buzzer To deactivate the Home mode simply press the HOME button Terminal Block with Trigger 3 Jumper Note Arming the system deactivates the Home mode After disarming reactivate the po nehrae Home mode if desired Battery Receptacle Reset Button Low Battery LOW BATT Indicator When the charge level of the 9VDC backup battery not included is low the LOW BATT LED LCD Screen Layout will flash once every 1 5 seconds Replace the battery in order to continue providing functionality Home Mode Auto Dial Time Date during a temporary disruption in power Activated N Siren Alarm Call Back Rings Armed ol Note In order to avoid potential damage due to battery leakage do not leave a low battery in Alarm Triggered Disarmed the unit Also be sure to remove the battery if the unit is unused for a period of time PASSWORD MEMORY LEARN I Bee cycle entry View Function To view the last 5 sensor trigger events while in standby mode press the DOWN button 2 D L 5 D L D L L 2 T T To view stored emergen
3. Battery D Cover A 9VDC Battery not included Power Fig 2 a If the dialer is to be powered from the alarm control panel connect the alarm power outputs to the DC Plug to terminal block included and plug into the dialer s DC power jack see pg 3 gi b If using a 12VDC adapter not included plug the adapter into the dialer s DC power jack Connect one end of the included telephone cable to an existing Touch Tone line wall socket and the other end to the dialer s LINE jack The wall socket line must be connected to the dialer s LINE jack for proper operation Optionally connect an extension telephone using the telephone s cable not included to the TEL jack Fig 3 Reattach the cable cover Fig 3 lf an external alarm is desired connect according to the wiring diagram see pg 3 For wall installation place the unit over the heads of the screws installed in step 2 Fig 1 and slide down Check that the unit is firmly attached and tighten or loosen the screws as needed 10 Once all connections are made the dialer is ready to be programmed SECO LARM U S A Inc 5 ENFORCER Voice Dialer Programming the Voice Dialer The setup mode may only be accessed when the dialer is in standby mode If no key is pressed within 15 seconds the dialer will automatically exit the setup mode Setting and Changing the PIN Number 1 Enter the current PIN number factory preset PIN number is
4. the SECO LARM policy is one of continual development and improvement For this reason SECO LARM reserves the right to change specifications without notice SECO LARM is also not responsible for misprints or typographical errors Copyright 2014 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in part without the written permission of SECO LARM SECO LARM U S A Inc 16842 Millikan Avenue Irvine CA 92606 Website www seco larm com Phone 949 261 2999 800 662 0800 Email sales seco larm com oA PIHLKI MiE 921CPQ_141204 docx 16 SECO LARM U S A Inc ENFORCER Voice Dialer Manual 20 15 01 01 I 00 eee Models Available Certification E 921CPQ When triggered by an alarm system the ENFORCER Voice Dialer can call up to 5 numbers and deliver a user recorded 20 second voice message playing repeatedly for one minute Each number can contain up to 32 digits including tones and pauses The LCD shows the number being dialed at each stage of the dialing process The receiver can then listen in or broadcast a message to the room occupants or can disarm the system The same functions are available by remote call in as well as arming the system The dialer includes a home mode acting like a door chime when the owner is present and a panic button The 105dB built in siren alarm can be programmed on or off J SECO LARM S ENFORCER Voice Dia
5. Panic Button Use 1 When the PANIC button is pressed the siren will sound immediately and auto dialing will commence without delay If the siren has been programmed to SOUND OFF the siren will not sound but silent dialing will commence 2 Tocancel the alarm and stop auto dialing enter the PIN number and press the ARM DISARM button The dialer is now disarmed Remote Control by Telephone The system can be remotely controlled and monitored through any Touch Tone phone including mobile phones The user may either arm or disarm the system listen in on any activity in the room or broadcast a message to those in the room 1 REMOTE CONTROL WHEN ALARM IS ACTIVATED When an alarm has been activated and the voice dialer dials the pre programmed emergency numbers the person who answers the call will hear the pre recorded message and may press one of the following function codes at any time to control the system remotely Function Press key code End call The user should hear a beep in response If not enter the function code again 2 REMOTE CONTROL BY USER CALL IN CALL BACK A Using a mobile phone or any Touch Tone phone dial the phone number that the voice dialer is connected to The voice dialer will answer and beep once after the number of rings in the pre programmed call in ringer detect cycle 3 5 7 or 10 rings see pg 8 B Enter the PIN Number on the phone s keypad The dialer will beep tw
6. alarm after normal entry The factory default is 20 seconds but can be user programmed for 0 5 10 15 or 20 seconds 1 Enter the PIN number and press the PROG button eight times or until ENTRY flashes on the LCD screen Press the ARM DISARM button to accept Press the DOWN or UP button to select 0 5 10 15 or 20 seconds and press the ARM DISARM button to accept The dialer will beep once Press the DOWN or UP button to select other setup categories or press the PROG button until the programming icons disappear to exit the setup mode Setting the Date and Time Enter the PIN number and press the PROG button nine times or until the clock icon flashes on the LCD screen Press the ARM DISARM button to accept The date and time will appear on the LCD screen as 5 sets of numbers representing the year month date hour and minute respectively The first set of numbers year will be flashing indicating that this can now be changed Press the DOWN or UP button to select the correct number for the year and press the ARM DISARM button to accept and move to the next position Repeat for each position until complete Press the PROG button until the programming icons disappear to exit the setup mode Note Time is shown using a 24 hour clock Record and Play Back Emergency Message 1 2 SECO LARM U S A Inc 9 Enter the PIN number and press the REC PLAY butt
7. use of this product IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national state and local laws and statutes related to monitoring and recording audio and video signals SECO LARM will not be held responsible for the use of this product in violation of any current laws or Statutes WARRANTY This SECO LARM product is warranted against defects in material and workmanship while used in normal service for one 1 year from the date of sale to the original customer SECO LARM s obligation is limited to the repair or replacement of any defective part if the unit is returned transportation prepaid to SECO LARM This Warranty is void if damage is caused by or attributed to acts of God physical or electrical misuse or abuse neglect repair or alteration improper or abnormal usage or faulty installation or if for any other reason SECO LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship The sole obligation of SECO LARM and the purchaser s exclusive remedy shall be limited to the replacement or repair only at SECO LARM s option In no event shall SECO LARM be liable for any special collateral incidental or consequential personal or property damage of any kind to the purchaser or anyone else NOTICE The information and specifications printed in this manual are current at the time of publication However
8. 3 LQ gt lt 3 o D r D D L Current PIN PROG ARM DISARM New PIN ARM DISARN PROG x9 2 Setting Emergency Telephone Numbers see pgs 6 7 PROG x2 ARM DISARM DOWN or UP ARM DISARM PROG x8 3 PROG x2 ARM DISARM DOWN or UP DELETE PAUSE ARM DISARM PROG x8 W Lo Zg Q p Kk Y 4 gt yA wn h IS D o 5 Q Tl S D oO S S TAE on D D gt e 3 nae OZ on 4 gt 4 gt 5 KS LN PIN PROG x4 ARM DISARM DOWNJ or UP ARM DISARM PROG x6 5 Setting the Auto Dial Function see pg 8 PIN ARM DISARM DOWN or UP ARM DISARM 6 Setting the Number of Auto Dial Cycles see pg 8 PIN ARM DISARM DOWN or UP ARM DISARM 7 Setting the Number of Call in Rings see pg 8 PIN ARM DISARM DOWN or UP ARM DISARM 8 Setting the Entry Delay Time see pg 9 PIN ARM DISARM DOWN or UP ARM DISARM 9 Setting the Date Time see pg 9 PROG x9 ARM DISARM DOWN or UP ARM DISARM PROG x2 11 Playback Message see pg 9 12 Test Auto Dial Function see pg 10 In Standby Mode Press and Hold PROG DOWN or UP Check to see if number is dialed 14 Remote Control by Telephone see pgs 11 12 Receive Call Press Key Code on Telephone Keypad Dial Voice Dialer Number Press Key Code on Telephone Keypad 16 Activate Dea
9. ENFORCER Voice Dialer Troubleshooting e Try re entering the PIN number to ensure that you have entered it correctly e While pressing and holding the PROG button use a pen or paper clip to press the RESET button on the back of the dialer This sets the PIN number to the default 000 Then try to arm disarm again e Make sure that the telephone line is working e Make sure that you have programmed at least one telephone number into the unit and that the full number has been stored e Make sure that the system is in Auto Dial mode e Ensure that the line to the wall jack is plugged into the dialer s LINE jack and any phone extension connected to the dialer is plugged into the dialer s TEL jack Unit doesn t respond to a call Check to see if another unit fax or answering machine back could be answering the call and remove the other unit e Adjust the call in ring detect setting so the dialer will answer Difficulty in activating room e Try pressing the code key again monitor by telephone remote e Move to a quieter location as ambient noise may affect the control dialer s ability to detect the tone signal Dialer will not arm disarm Dialer will not dial out NOTE While the system can provide valuable protection to home and property when properly installed it cannot guarantee complete protection against intrusion SECO LARM is not responsible for any losses or damage which may occur during the
10. G button four times or until the alarm icon amp flashes on the LCD screen 2 Press the ARM DISARM button to accept The dialer will beep once 3 Press the DOWN or UP button to select either SOUND ON or SOUND OFF and press the ARM DISARM button to accept 4 Press the DOWN or UP button to select other setup categories or press the PROG button until the programming icons disappear to exit the setup mode SECO LARM U S A Inc 7 ENFORCER Voice Dialer Programming the Voice Dialer continued Setting the Auto Dial Function The user can choose whether or not the dialer will dial the emergency numbers when triggered The factory default is ON 1 Enter the PIN number and press the PROG button five times or until the phone icon 3 flashes on the LCD screen Press the ARM DISARM button to accept Press the DOWN or UP button to select either ON or OFF and press the ARM DISARM button to accept The dialer will beep once Press the DOWN or UP button to select other setup categories or press the PROG button until the programming icons disappear to exit the setup mode Note 1 When the dialer is in standby mode and the amp icon is ON the auto dial is disabled 2 When the dialer is in standby mode and the 3 icon is OFF the auto dial is enabled Setting the Number of Auto Dial Cycles This can be set from 1 5 cycles Th
11. M DISARM button Example 3 To store a local number 555 2858 After scrolling to the desired number location enter 5552858 and press the ARM DISARM button 5 Repeat for the other numbers to be stored up to 5 total 6 Press the DOWN or UP button to select other setup categories or press the PROG button until the programming icons disappear to exit the setup mode Note If the dialer is programmed to call a voice pager service which requires operator assistance the service should be notified in advance regarding the meaning of the message Consult local authorities concerning the permissibility of automatically dialing their emergency numbers before programming Deleting a Stored Phone Number 1 Enter the PIN number and press the PROG button twice or until MEMORY flashes on the LCD screen Press the ARM DISARM button to accept Press the DOWN or UP button to select the number you wish to delete Press the DEL PAUSE button to delete the number Press the DOWN or UP button to select other setup categories or press the PROG button until the programming icons disappear to exit the setup mode OF os ee NS Learn This function is unused Setting the Siren Function This setting allows the user to choose between an audible alarm when triggered or a silent alarm while dialing the emergency numbers The factory default is ON 1 Enter the PIN number and press the PRO
12. OS E EE AT E E E 13 Program PIAnnel cccccccccessecsessesseeeeeees 14 FOG Parn 00 tescicsscosaccocaransntesiarestnnianteanenncans 14 Summary Programming Operation Chart 15 Also Available from SECO LARM 15 Troubleshooting ccccccecesesesseesessreeeeeees 16 e Trigger activated alarm and dialer with user programmable 20 second alarm message e 16 Digit large display with date time and function icons e 3 Triggers 1 N C 2 NO NC for multiple zone security e Call in at any time to listen in to room broadcast to room arm and disarm dialer e Listen in broadcast messages to room and or disarm during dialer call out e Programmable PIN number and entry delay timing e 5 Programmable emergency telephone numbers up to 32 digits each e Programmable auto dialing cycle repeat times Home mode function acts as a door chime when user is at home Panic button Back lit keypad Touch Tone dialing e 9V battery backup battery not included Wall mountable Built in line seizure Built in flash memory to protect against system data loss in case of power failure Low battery indicator for backup battery battery not included DC power input jack power adapter not included Built in 105dB alarm with programmable alarm on off Built in auxiliary output for external alarm or siren SECO LARM U S A Inc ENFORCER Voice Dialer Summary Programming Operation Chart 1 W 12 S gt pel 5 Q
13. PAUSE button for 2 seconds until the letter F appears on the LCD screen and then continuing with the extension number as usual A or can also be entered by pressing and holding for two seconds the DOWN or UP buttons respectively The Sign shows as 1 and the sign shows as on the LCD screen Example 1 To store a number with area code 1 214 555 2858 and an office extension 205 where the PBX requires a 2 second pause before the extension After scrolling to the desired number location enter 12145552858 press the DEL PAUSE button for 2 seconds until the letter F appears on the LCD screen enter 205 and press the ARM DISARM button 6 SECO LARM U S A Inc ENFORCER Voice Dialer Operating the Voice Dialer continued Note When the siren has been programmed to SOUND OFF the siren will not sound and the dialing will commence silently after the delay time has passed When the call is answered the receiver will hear the user recorded 20 second emergency message Note If the voice dialer is not connected to a working telephone line the dialer will beep 4 times and the siren will begin to sound without attempting to continue dialing out this overrides the SOUND OFF setting 2 To disarm the system enter the PIN number and press the ARM DISARM button The dialer will sound a long beep and the word ARM will disappear from the LCD screen
14. and 2 Trigger 3 Auxiliary output current max Operating temperature 32 104 F 0 40 C Storage temperature Weight Dimensions 611 16 x411 16 x11 2 170x119x38 mm Trigger inputs Trigger input timer Wiring Diagram Back Connection Area Cover Removed eee Note For proper operation the telephone extension line and wall jack line must not be reversed eo Te Telephone Wall Jack E 964 D390Q Wil SM 206Q a Telephone Extension External Alarm Siren Q Power Adapter Not Included or CA 161T M E Sl DC Plug to Terminal Buzzer O P E Block Buzzer O P SM 200Q NO NC Trigger in 1 NO NC Trigger in 2 N C Trigger in 3 Trigger ground E 964 D390Q Photobeam Detectors SM 200Q Magnetic Sensors and SM 206Q Concealed Magnetic Sensors shown as examples only For other sensors and products available from SECO LARM please visit our website at www seco larm com SECO LARM U S A Inc 3 ENFORCER Voice Dialer ENFORCER Voice Dialer Overview Operating the Voice Dialer continued Front LCD Display Home Mode Use Speaker To turn off the alarm function and use the dialer as a door chime set the dialer to Home mode A REC PLAY LED chime will ring any time one of the sensors is triggered LOW BATT LED To activate the Home mode POWER LED 1 Press the HOME button once One chime will sound and the word
15. ctivate Home Mode see pg 13 In Standby Mode HOME 10 Record Emergency Message see pg 9 PIN REC PLAY Speak message up to 20 seconds REC PLAY 13 Arm Disarm System see pgs 10 11 PIN ARM DISARM 15 View see pg 13 Last 5 Sensor Trigger Records In Standby Mode 4 DOWN In Standby Mode Also Available from SECO LARME Auto Dialer E 921APQ Door Window Switches Magnetic Contacts etc LED Strobe Light SL 1301 BAQ 19 Shock Vibration Detector Photobeam Sensor SS 040Q E 931 S35RRQ sp For a complete listing of SECO LARM products please visit us online at www seco larm com SECO LARM U S A Inc 15 Tamper Switch SS 072Q ENFORCER Voice Dialer Program Planner Use these charts during setup to record phone numbers and sensor locations for future reference It is recommended that you use a pencil during setup and redo it in ink afterwards The user should keep in a safe easily accessible location and a copy should be retained by the installer Program Numbers Date NUMBER TELEPHONE NUMBER include area code and dialer prefix as needed add PBX PRIORITY pause and extension if applicable see p 6 7 FCC Part 68 This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA On the bottom of the device of this equipment is a label that contains among other information a product identifier in the format US 7M7TE02BE921CPQ an
16. cy telephone numbers while in standby mode press the UP button TRIGGER HOME ARM Note After 10 seconds of inactivity the voice dialer will automatically exit the view mode and return to standby Note For explanation of symbols please see Programming the Voice Dialer on pages 6 9 7 Ips Installing the Voice Dialer 1 Note You can program the telephone numbers and voice messages prior to connecting the power as long as the 9V battery is installed The standby battery should provide about 20 hours of operation 2 The voice dialer is only suitable for single phone lines It is not compatible with fax machines Make sure that the full telephone numbers have been stored as they would normally be dialed from a local phone Note The Voice Dialer uses EEPROM to retain memory in the event of a power loss 3 Set the number of Call in rings to be less than the voicemail or message answer point 4 SECO LARM U S A Inc SECO LARM U S A Inc 13 ENFORCER Voice Dialer Operating the Voice Dialer continued Remote Control by Telephone Remote Control by User Call in Call Back continued 12 C Press one of the following function codes to control the system remotely Function Press key code The user should hear a beep in response If not enter the function code again Note Should the user have difficulty activating functions remotely by telephone there may be too much ambient noise interference Try pressi
17. d REN 0 11B for this equipment This equipment uses the following USOC jacks RJ 11 RJ45 USB Power Jacks A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA A compliant telephone cord and modular plug is provided with this product It is designed to be connected to a compatible modular jack that is also compliant See installation instructions for details REN RINGER EQUIVALENT NUMBERS STATEMENT Notice The Ringer Equivalence Number REN assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5 If this equipment US 7M7TEO2BE921CPQ causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required But if advance notice isn t practical the telephone company will notify the customer as soon as possible Also you will be advised of your right to file a complaint with the FCC if you believe it is necessary The telephone company may make changes in its facilities equipment operations or procedures that could affect the operation of the equipment If this happens the telephone c
18. e factory default is 3 cycles meaning that the voice dialer will dial each programmed number 3 times 1 Enter the PIN number and press the PROG button six times or until CYCLE flashes on the LCD screen Press the ARM DISARM button to accept Press the DOWN or UP button to select your choice of 1 5 cycles and press the ARM DISARM button to accept The dialer will beep once Press the DOWN or UP button to select other setup categories or press the PROG button until the programming icons disappear to exit the setup mode Setting the Number of Call in Rings This sets the number of call in rings after which the voice dialer will answer The factory default is 5 rings but can be user programmed for 3 5 7 or 10 rings i Enter the PIN number and press the PROG button seven times or until the bell icon amp flashes on the LCD screen Press the ARM DISARM button to accept Press the DOWN or UP button to select 3 5 7 or 10 and press the ARM DISARM button to accept The dialer will beep once Press the DOWN or UP button to select other setup categories or press the PROG button until the programming icons disappear to exit the setup mode SECO LARM U S A Inc ENFORCER Voice Dialer Programming the Voice Dialer continued Setting the Entry Delay Time This allows the user to set the length of time before the alarm will sound to allow time to disable the
19. ice if the correct code has been entered If a wrong code is entered the dialer will disconnect automatically and the user must dial in again SECO LARM U S A Inc 11 ENFORCER Voice Dialer Testing the Auto Dial Function To test the auto dial function while in standby mode press and hold the PROG button for at least two seconds When you hear a beep tone enter the memory location 1 5 of the number you wish to test The voice dialer should then dial the chosen number Resetting the Voice Dialer To reset the Voice Dialer press and hold the PROG button and use a pen or paper clip to press the RESET button located near the battery receptacle cover on the back of the unit and release The unit will return to the factory preset PIN number 000 All other user programmed settings except the date and time will be retained Line Seizure lf the telephone line that the dialer is connected to is in use the dialer will seize the line disconnecting the current call to dial out This ensures that the dialer is able to dial emergency numbers promptly Note For proper operation the line to the wall jack must be connected to the LINE jack of the dialer A telephone extension if used may be connected only to the TEL jack of the dialer Operating the Voice Dialer Arming and Disarming the System if 10 To arm the system enter the PIN number and press the ARM DISARM button The dialer will s
20. ler Table of Contents FEATS sieniretki e a 2 EEE E ate tae E EN 3 Specifications ceseesesssssseesseesessersessesaeees 3 Wiring Diagram ccecesecsessesessecseeseeseeseerees 3 VOT VOW secetesc carts jisatinsndicedeayadctetecatedetens dadisceeeits 4 LCD Screen Layout cccccssesessseees 4 Installing the Voice Dialer 4 5 Programming the Voice Dialer 6 9 Setting and Changing the PIN Number 6 setting Emergency Phone Numbers 6 7 Deleting a Stored Phone Number 7 Setting the Siren Function T Setting the Auto Dial Function 0 8 setting the Number of Auto Dial Cycles 8 setting the Number of Call in Rings 8 setting the Entry Delay Time 08 9 Setting the Date and Time cccceeeee 9 Features Record and Play Back Emergency Message septs ccectaecitaieteautininssctscuartnendeisvetitonsest 9 Testing the Auto Dial Function 06 10 Resetting the Voice Dialer ccceeceee 10 Line Seizure conte sawicnaadeastnasingsaeeeotemiemant 10 Operating the Voice Dialer 0 10 13 Arming and Disarming the System 10 11 Panic Button USe cceceeeeeseeeeeeenees 11 Remote Control by Telephone 11 12 Home Mode US6 c cccccccsssseseeeees 13 Low Battery Indicator cccseeeseeeeeeeees 13 View FUNCTION ccccccccececeecseeseeseseeeeeees 13 NAN
21. ng the code key again or move to a quieter location as ambient noise above 68dB may affect the auto dialer s ability to detect the tone signal FUNCTION EXPLANATIONS LISTEN IN Pressing 1 allows a user to hear sound in the room for 50 seconds A beep will sound at 30 seconds to remind the user that the listen in time will soon end Pressing 1 again will reset the 50 second period and entering any other key code will end monitoring and perform the function If there is no other key press the call will disconnect at the end of the 50 seconds BROADCAST Pressing 2 allows a user to speak to the person in the room for 50 seconds A beep will sound at 30 seconds to remind the user that the time will soon end Pressing 2 again will reset the 50 second period and entering any other key code such as 1 Room Monitor will end broadcasting and perform the other related function If there is no other key press the call will disconnect at the end of the 50 seconds Note Alternating between Listen In and Broadcast may be useful for a conversation with the room occupant but a user cannot speak and listen at the same time END CALL Pressing 3 will end the call ARM SYSTEM Pressing 5 during a user callback will arm the system confirming with three short beeps and automatically hang up If there are 5 rapid beeps after three short beeps it means a door window is n
22. ompany will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service If trouble is experienced with this equipment US 7M7TEO2BE921CPQ for repair or warranty information please contact SmartRG Inc If the equipment is causing harm to the telephone network the telephone company may request that you disconnect the equipment until the problem is resolved Connection to party line service is subject to state tariffs Contact the state public utility commission public service commission or corporation commission for information If your home has specially wired alarm equipment connected to the telephone line ensure the installation of this US 7M7TEO2BE921CPQ does not disable your alarm equipment If you have questions about what will disable alarm equipment consult your telephone company or a qualified installer 14 SECO LARM U S A Inc ENFORCER Voice Dialer Parts List 1x Voice dialer unit 1x Telephone cable 1x Remote control instruction card 1x DC Plug to terminal block 3x Plastic wall anchors 3x Wall mount screws 1x Wall mounting template 1x User manual Specifications Speaker On Current draw Max at 12VDC 480mA Up to 20s rs 5 32 auto detected Emergency voice message length user recorded Programmable emergency phone numbers Maximum digits per telephone number Backup battery type life not included Alarm sound level at 12 30cm O O Oo Triggers 1
23. on Speak your message into the microphone of the voice dialer The maximum message length is 20 seconds When finished press REC PLAY again Note You may wish to include instructions for disarming the unit in your message since you may not remember how to do so at a later date when you receive a message that the alarm has been triggered A suggested message could be Your name s security alarm has been activated Please enter a command 1 to monitor the room 2 to broadcast a message to the room 3 to end this call or 6 to disarm the system To listen to a message press the REC PLAY button
24. ot closed The dialer will then give 5 seconds to disarm the system DISARM SYSTEM Pressing 6 will disarm the system and automatically hang up Note If the user enters an incorrect password or key code the voice dialer will sound 5 beeps and automatically hang up SECO LARM U S A Inc ENFORCER Voice Dialer Installing the Voice Dialer continued if select a location for the dialer near a standard electrical outlet if user supplied 12VDC adapter is to be used a telephone wall jack and the alarm control panel but out of sight The dialer should not be exposed to direct sunlight or rain and must not be mounted near heat sources such as radiators heating ducts or stoves For wall mount use the wall mounting template to pa drill holes and attach 3 screws into the wall at the aa desired location For convenience 5 6ft 1 5 2m 1 above the floor is recommended Fig 1 o 6ft 1 5 2m Remove the cable cover and battery cover from ale Lua el the back of the voice dialer Fig 2 4 Install a 9VDC backup battery not included Reattach the battery cover Connect the dialer to up to three detectors or groups of detectors in series using the connection terminals as shown in the wiring diagram see pg 3 The dialer can also be connected to three Cable separate alarm control panel outputs of a separate Cover alarm system When Trigger 3 is used the jumper connection to ground must be removed
25. ound three short beeps and the words ARM will appear on the LCD screen After 60 seconds there will be a single beep tone to indicate that exit delay time has passed and the alarm is now fully armed During the 60 second delay time after the system is armed if the system detects trigger 3 indicating an open door or window a beep tone sounds for 5 seconds the reminder CLOSE PLEASE appears on the LCD screen and the word TRIGGER flashes If after 60 seconds that door or window is not closed the alarm will sound and auto dialing will commence After the delay when the system is fully armed if a door or window connected to the alarm is opened the LCD screen will flash the word TRIGGER After the adjustable entry delay time has passed the siren will begin to sound 30 seconds on and 30 seconds off and auto dialing will commence according to the programmed sequence and cycle times SECO LARM U S A Inc ENFORCER Voice Dialer Programming the Voice Dialer continued Example 2 To store a number with area code 1 949 555 1234 and an office extension 200 where the PBX requires a 2 second pause before the extension After scrolling to the desired number location enter 19495551234 press the DEL PAUSE button for 2 seconds until the letter F appears on the LCD screen press the DOWN button for 2 seconds until the 1 appears on the LCD screen enter 200 and press the AR
Download Pdf Manuals
Related Search