ltm-6000d all format transcoder
Contents
1. Environmental Conditions A cool ventilated operating environment must be provided for the LTM 6000D It is advised that the unit not be sandwiched between two heat generating pieces of equipment It would be wise to allow a 1RU space above and below the unit Do not place the LTM 6000D directly above a VTR Some VTRs emit a high level of RF from the head amplifier and this can be picked up by the LTM 6000D and cause interference It is advisable that the unit be at least 4RU away from any such device High level of RF in the environment such as certain medical or radio towers can cause interference It is recommended that in such environments proper shielding be provided for the unit Extreme heat and cold can also cause the unit to malfunction Be certain that the unit is not exposed to harsh temperature changes outside the specifications listed in this manual Dirt and ash can cause damage to any piece of precision equipment Keep the unit in a clean moisture and smoke free location Follow the hazard warnings provided at the end of this manual Power Up Procedures It is recommended that you have all devices properly wired before any power up is performed Based on the nature of DV and DV devices the proper sequence must be followed Power up the LTM 6000D first and make sure it settles in its default mode DV DECODE Setup the LTM 6000D for the operation you require and then power up the other DV device Computer based DV devices such as No2. or Y C or Y Pb Pr Y U V or SD SMPTE259M C Page 9 800 898 0759 e 845 339 9555 e 2000 Sterling Road Mount Marion NY 12456 e www lairdtelemedia com m NExT To ENTER Video 20 EG UP DOWN UP DOWN NTSC DV DV CAM or or PAL DVC Pro 25 DECODE Next ENTER NExT ENTER Audio Input UP DOWN UP DOWN Balanced 48kHz 16 bit or or AES EBU 32kHz 12 bit ENCODE NEXT TO ENTER S DOWN Genlock Audio a EN lt DOWN w LTM GOOOD ALL FORMAT TRANSCODER NExT ENTER 40 40 UP DOWN On or Off Next ENTER 100 la Audio DOWN UP DOWN OdB to 63dB UP gt lt DOWN Page 10 lt DOWN This option appears only when Studio Genlock is ON NExT ENTER Phase UP M ie Ph 255 Next TO ENTER Video System UP DOWN NTSC or PAL 800 898 0759 e 845 339 9555 e 2000 Sterling Road Mount Marion NY 12456 e www lairdtelemedia com AGI LTM 6000D EDTA ALL FORMAT TRANSCODER TELE GC These options appear This option appears only when Studio only when Output Genlock is ON Timecode is ON NExT To ENTER NExT TO ENTER TO ENTER NExT ENTER Horizontal Vertical Offset Output VITC PN Offset Pixel lt DOWN Lines lt DOWN Timecode l
3. 6000D as a Phillips DV Device or Camcorder This verifies that the LTM 6000D and the OHCI FireWire card are working properly and Windows is recognizing the connection properly This does not mean that your software will auto matically work Some software requires that certain templates be loaded before the DV device is online Study your software manual and follow any instructions provided for such operations Using The LTM 6000D with Apple Macintosh For Apple Mac based systems the LTM 6000D will be recognized as a DV DECK or VTR DV Decks and Camcorders To interface with standard DV IEEE1394 FireWire decks such as SONY DSR series Panasonic DVCPRO and any other such device simply select the proper DV MODE OS in the menu setups Select DV DECK for interface requirements between analog equipment amp DV VTRs Other DV Transcoders If there is a need to interface the LTM 6000D with another DV transcoding device always choose the DV DECK mode for this operation The LTM 6000D was tested with several of the most popular DV transcoders for operation If you should encounter a device that does not inter face properly please contact customer service Studio and Facility Integration For system integration into larger facilities it may be required to GENLOCK the LTM 6000D to provide system phasing to HOUSE REFERENCE The LTM 6000D can be GENLOCKED to standard CVBS video BLACKBURST Once this feature has been activated the LTM 6000D ca
4. in multi format signal transcoding and conversion Designed to fit seamlessly into any profes sional broadcast or post production media facility the LTM 6000D will provide high quality performance and operation for years to come The product is designed as an integrated system to handle the demanding media environment where a variety of signal conversion and transcoding requirements exist The LTM 6000D also provides a bridge between analog and digital equipment to create a hybrid solution to a fast moving evolution of signals from analog to digital The simple block diagram below is but a very basic representation of the technology operations that the LTM 6000D can perform The unit is built around the latest powerful IEEE1394 DV CODEC One of the most common functions of the LTM 6000D is to provide the easy bi directional conversion of analog to DV 1394 The LTM 6000D is the final result of many years of research and provides a flexible solution as a signal bridge and beyond The LTM 6000D can also provide basic signal transcoding conversion between any standard analog and digital format signal Thus as a stand alone unit it can serve as a signal format transcoder and provide a very wide variety of daily operations Software is the key to the smooth integration of the LTM 6000D It is self diagnosing and will perform a complete system check every time you power up the unit The Operating System provides seamless navigation through the very flexibl
5. DOWN Time Code lt DOWN Code Type UP DOWN UP DOWN UP DOWN V0 0 Yes LTC NExT TO ENTER to or or VITC V0 7 No VITC 94 006 Type ENCODE 2 RS 422 UP DOWN CVBS or or Y UN or External Page 12 800 898 0759 e 845 339 9555 e 2000 Sterling Road Mount Marion NY 12456 e www lairdtelemedia com 222 LTM D A RD 6000 EDTA ALL FORMAT TRANSCODER WARNING ALL USER SETTINGS WILL BE LOST NExT TO ENTER TO ENTER LCD Factory ee oe gt 0 UP DOWN ARE You SURE On Press any button other ot than NEXT to Exit Of To Slait sono eneeeaE c E REPE DECODE of Menu lt 1 These options appear WARNING ALL USER SETTINGS aaa WILL BE LOST NExT TO ENTER NExT TO ENTER NExT To ENTER ENTER Time LCD Factory jj Offset 107 Code Display UP a Backlight DOWN DOWN DOWN UP DOWN UP DOWN UP DOWN ARE You SunE Offset 4 DISPLAYS THE CURRENT On Press any button other to Time CODE than NEXT to Exit Offset 4 ON THE LCD Off ENCODE Page 13 800 898 0759 e 845 339 9555 e 2000 Sterling Road Mount Marion NY 12456 e www lairdtelemedia com LTM GOOOD AIRD ALL FORMAT TRANSCODER SYSTEM APPLICATION DRAWINGS a 6 TIT 00 s ER 1 1 SS E i Ba
6. Model LTM GOOOD User Manual 4 WORLD S MOST ADVANCED TRANSCODER MULTIFORMAT SIGNAL TRANSCODER with DV SDI amp TIMECODE INSERTION 2006 Laird Telemedia CE AGI LTM 6000D ALL FORMAT TRANSCODEH TABLE CONTENTS Package Contents amp Warranty Information 1 Product 1 2 The Laird Quality 2 Front amp Rear Panel Controls amp Connections 3 4 LTM 6000D 5 Hookup amp Powering 6 Apple amp Windows User 10168 1 Deck Control RS232 RS422 Time 8 Using as a Stand Alone 8 Menu Controls amp Operation 9 13 System Applications Typical Hook Up Diagrams 14 Avid Xpress DV 4 6 amp Final Cut User Notes 15 Safety P BCHU HOS 16 800 898 0759 845 339 9555 2000 Sterling Road Mount Marion NY 12456 www lairdtelemedia com AGI LTM 6000D ALL FORMAT TRANSCODER TELE GC Warranty Information Laird warrants your product to be free from malfunctions and defects in both materials and workmanship for one year from the date of pur chase Please see the enclosed warranty card for full details or your lo
7. NEXT button the second time after the DOWN UP buttons will result in the function not being saved and FTT TA you will be advanced to the next level of functions 5 2 DOWN UP Used in conjunction with the NEXT button this button will advance your menu choices down eatin ub the tree of functions for the main function selected by the NEXT button If you pass a selection simply press VELIE CM BINE TTA 6 EH C the UP button to move back to that function that was selected previously This manual provides a MENU graphic which shows in detail the entire menu entries and selections It has been designed to make it easy to understand the flexibility of the LTM 6000D Study this graphic with the unit powered up and try the functions You will soon see how easy it is to use LTM 6000D Page 8 800 898 0759 845 339 9555 2000 Sterling Road Mount Marion NY 12456 www lairdtelemedia com AGI LTM 6000D ALL FORMAT TRANSCODEH DECODE NExT TO ENTER pessoas UP gt Analog Audio UP gt MODE MENU DOWN UP DOWN 048 to 63dB NExT ENTER LTM 6000D eee 4 L End Press Back Next BACK NEXT Mode gt of Menu UP DOWN Decode or Encode NEXT TO ENTER ENCODE DOWN Video MODE MENU L UP gt Input Z 400WN UP DOWN CVDS
8. U you must use a 110 75Q adapter such as the Connectronics AES EBU1 AES EBU2 It is important to properly match the impedance of your signals Component YUV video signals should be wired with high grade RG 59U shield cable using high grade BNC connectors Be certain to use exact equal lengths for R Y V B Y U and Y signals It would be advisable to use color coded cables for easy identification during cabling The LTM 6000D can be used as a desktop device or in a EIA Rack mounted system The only limitation is that the front panel LCD display must be viewed for certain setup functions For applications where the unit must be rack mounted away from operators RS232 Remote Control Software that runs in Windows can be used The software also has signal processing functions that are only available by using this software package The RS 232 remote software does have some operational limitations that will be covered later in this manual The control software is available from the LAIRD TELEMEDIA website www lairdtelemedia com Power Options The LTM 6000D was designed to be powered by a high grade in line switching power supply with a regulat ed output of 12Volts DC 4 AMPS Maximum The unit may be powered by any such quality power supply or 12 Volt Battery The power entry is a standard 4pin XLR Male with pin 1 GROUND and Pin 4 POSITIVE HOT Using any other source of power is not recommend as it may damage the unit or cause it to mal function
9. ates an efficient and uncluttered design The LTM 6000D also features a powerful menu operating system The use of high speed digital logic and dedicated audio video semiconductor technology allows the fast configuration of setups and equipment integration which performs well in broadcast facilities The audio and video signals are all buffered in and out to provide proper line drive and cable coupling High quality A V connectors are used for all input and output hardware connections MEDIA DERT ENU 3 ERES DIM Lx 1 LCD Status Display 6 Channel 1 LED Level Meter 2 Menu Back Button 1 Channel 2 LED Level Meter 3 Menu Next Button 8 Channel 1 Level Adjustment BALANCED INPUT 4 Menu Down Button 9 Channel 2 Level Adjustment BALANCED INPUT 5 Menu Up Button 10 Power On Off Switch Page 3 800 898 0759 845 339 9555 2000 Sterling Road Mount Marion NY 12456 www lairdtelemedia com LAIRD TELE EDIA GC ALL FORMAT TRANSCODEH REAR PANEL FEATURES 1 Composite Video Input 2 YC Video Input 3 Component Y Input 4 Component B Y Input 5 Component R Y Input 6 501 Signal Input 7 LTC Timecode Input 8 Timecode Input 9 Balanced Audio Input Ch1 10 Balanced Audio Input Ch2 11 AES EBU Audio Input 12 IEEE1394 DV Firewire 1 0 POWER UP PROCEDURES 27 LTC Timecode Output VITC Timecode Output SDI Signal Ou
10. cal dealer or Distributor for questions concerning the warranty Technical Support Laird maintains a free user support web site to help with all of your technical support needs Visit www laird support com Getting Started We recommend that you Unpack the equipment carefully and save the original box and packaging materials for possible future shipments Wi Review the contents of this instruction manual In addition to the unit itself the package should also contain AC Adaptor 12 V 4 Pin XLR 9 Pin 5422 Control Cable 4 Non Slip Feet Warranty Card Power Line Cable USA 9 Pin RS232 Control Cable This Manual SPECIFICATIONS VIDEO INPUTS OUTPUTS DV 1394 I O DV25 8 bits IEEE1394a Full Duplex Isochronous AV 400Mbps DV25 DV DV CAM DVC Pro DV DVCAM NTSC 4 1 1 PAL 4 2 0 DVCPRO NTSC PAL 4 1 1 SMPTE259M SDI Digital Video SDI 75 ohm 10 bit resolution 270 MBit sec Inputs 1 SMPTE level digital Outputs 2 BNC SMPTE level digital Composite Video Inputs 1 BNC 1 0V p p into 75 ohms Outputs 2 BNC 1 0V p p into 75 ohms S Video Inputs 1 4 Pin Mini DIN 75 ohms Y 1 0V p p C 627mV p p Outputs 2 4 Pin Mini DIN 75 ohms Y 1 0V p p C 627mV p p Component Inputs 1 Set BNC x 3 75 ohms Y R Y B Y SMPTE level Outputs 2 Sets BNC x 3 75 ohms Y R Y B Y SMPTE level AUDIO INPUTS OUTPUTS AES EBU Input XLR 2 7 V p p across a 110 Ohm load 2 Channel 48 Khz 16 b
11. e IEEE1394 FireWire bidirectional conversion in addition to all digital and analog for mat conversion functions Menu Navigation Now that you are familiar with all the features and operational scenarios that are possible with the LTM 6000D it is time to study and learn to navigate the MENU Power up your product and first study and use the menu to get familiar with its operation It not required that you connect any equipment to the prod uct in order to practice the menus The Menu Buttons The four buttons located below the LCD menu display are used to navigate through the menu and adjust the settings of the LTM 6000D This system has been designed to work very similar to a computer style menu Before trying the menu buttons it is advisable that you carefully study the MENU TREE pages in this man ual It is important to know all the very various settings that the 6000D allows the user operator to control in the setup of the LTM 6000D into a system BACK Used to Back Out of a selection This button will return you back to the previous level If you have decided to not engage a function this button will back you out of it NEXT Used to advance to the next menu function level The UP and DOWN buttons are used in conjunc tion with this button and act as a cursor to navigate the menu choices Once you have arrived at a menu function choice the NEXT button must be pressed again to SAVE the selected choice Failure to press the mes
12. e set up and then goes one step further to use adaptive firmware to work with all computers and NLEs Settings are available for Windows 2000 NT XP and Macintosh systems The LTM 6000D can also be configured to connect directly to any DV VTR or Camcorder Firmware allows the unit to perfectly match any DV device so that a no compromise operation is provided Carefully read and study this operations manual It will guide you through the many features and performance settings of the LTM 6000D SDI SDI SMPTE259M C Component R Y B Y Y YUV SMPTE259M C Component R Y B Y Y YUV IRE TERTIA lt amp E 75 m ANY DIRECTION ANY TIME AES EBU IEEE1394 FireWire DV LTC VITC TIMECODE AES EBU IEEE1394 FireWire DV LTCNITC RS422 TIMECODE Page 5 800 898 0759 845 339 9555 2000 Sterling Road Mount Marion NY 12456 www lairdtelemedia com pU LTM 6000D EDTA ALL FORMAT TRANSCODER TELE GC Cables and Wiring Guidelines It is strongly recommended that you use only quality analog and digital cables for your connections to the LTM 6000D The SDI on the LTM 6000D is stan dard SMPTE 259M C and should be connected to digital coax for any distance over 6 feet Use high quality true 75 2 BNC connectors and try to avoid using adapters of any kind The AES EBU is provided via an XLR connector and is a transformer coupled 110Q driver To adapt this to a BNC AES EB
13. ing when using Final Cut Pro Version 3 x TECHNICAL SUPPORT For current support issues and answers to common questions please visit the Laird support website at http www laird support com or call 800 898 0759 Page 15 800 898 0759 845 339 9555 2000 Sterling Road Mount Marion NY 12456 www lairdtelemedia com pU LTM 6000D ALL FORMAT TRANSCODEH TELE E D GC N Safety Precautions To prevent fire or shock hazard do not expose this equipment to the environment of Humidity and or dust Do not use this equipment in an unprotected outdoor installation or any area classi fied as a wet area The operating temperature of this product must be kept between 40 C and 95 C Direct sun light or an intense source of heat direct or ambient must not be introduced to the product either by induction or contact Always keep the product on a stable and secure base or enclosure Do not drop the product or subject it to sudden heavy impact Provide adequate ventilation so that thermal characteristics do not cause an increase in product temperature to resulting in overheating Do not clean the unit by using electrically conductive or corrosive chemicals Always be certain to unplug the unit from AC wall power before any major cleaning Use a damp cloth only for cleaning Do not subject the product to electrical mains power over voltage The product must be used at the rated supply voltages indicated on the product rea
14. it or 32 Khz 12 bit Output XLR 2 7 V p p across a 110 Ohm load 2 Channel 48 Khz 16 bit or 32 Khz 12 bit Analog Inputs 1x 2 Channel Balanced XLR 0dBu nominal into 600 ohms Outputs 2x 2 Channel Balanced XLR 0dBu nominal into 600 ohms Page 1 800 898 0759 845 339 9555 2000 Sterling Road Mount Marion NY 12456 www lairdtelemedia com TELE GC E TIME CODE VIDEO CONTROL DATA POWER ENVIRONMENTAL AGI LTM 6000D ALL FORMAT TRANSCODER SPECIFICATIONS Standard operation LTC VITC over IEEE1394 RS422 Input locked to Reference Video BNC connector SMPTE LTC VITC Time Code Encode Decoded to IEEE1394 LTC In Out BNC RS422 In RS422 Standard Sony Machine Control VITC In BNC external or over Composite YC or Component inputs VITC Out BNC 1 0V p p into 75ohms Line selection of 13 15 16 18 or 20 22 Analog Decoder Analog Composite Component Y C to Digital Video Analog Encoder Digital ITU R 656 to Analog Output Composite Component Y C 525i 959 94 60Hz 625 50Hz SDI Decoder Equalizer Descrambler Deserializer SMPTE 259 10 bit 4 2 2 Digital Video to 656 parallel output 270Mbits Embedded audio in SDI stream EDH SDI control SDI Encoder Scrambler serializer from 656 to SDI SMPTE 259 10 bit 4 2 2 SDI Cable driver for SDI cable Internal Digital Video Buses 656 Input Buses 656 Output Bus DV 25Mbps over 1394 converted to 656 to video outputs Genlock Looping Gen
15. lanced Audio CH 1 Balanced Audio CH 2 Component YUV Video TimeCode 6 DV CONNECTIONS LAIRD il MERTA gt n fT JMRD AA i Balanced Audio CH 1 Balanced Audio CH 2 Component YUV Video Studio Reference CVBS The LTM 6000D provides a professional transcoding interface for the demanding multimedia environment of modern telecommunications facilities Indicated below are a few application diagrams which display the flexible and cost effec tive use of the LTM 6000D with other Laird products and various studio and production equipment UsinG MULTIPLE SOURCES WITH THE LTM 6000D oM o gt fre YUV Video m Studio Reference CVBS Page 14 800 898 0759 845 339 9555 2000 Sterling Road Mount Marion NY 12456 www lairdtelemedia com AGI LTM 6000D ALL FORMAT TRANSCODEH Using The LTM 6000D with Avid Xpress DV 3 5 4 Note Please be aware that this list has been compiled based on lab testing and user Feedback It is not a docu ment created by AVID or any official channel related to AVID TECHNOLOGIES 1 Before starting the AVID application the LTM 6000D should be set to its working settings like Encode Decode Mode or DVCam DVCPro 25 2 Switching the LTM 6000D On and Off while the AVID XPress DV application is running should be avoided as this can corrupt the d
16. lock input using composite video or Blackburst 1Vp p into 75bohms Horizontal Phase Adjust Range 128 Pixels Subcarrier Phase Adjust Range 360 256 Vertical Offset Adjust Range 0 7 Lines Compatibility Firmware DVCAM DVCPRO WIN98 ME 2000 XP FINAL CUT PRO AVID XPRESS PROAVID NEWS CUTTER Machine Control Standard Sony Machine RS422 control protocol Bi directional over Firewire IEEE1394 6pin DB9Female using standard RS422 9pin cables System Upgrades Firmware upgrades via RS232 serial port DB9Male Front Panel Control Push Button Switches and LCD select Main Menu Functions for all operations BACK NEXT DOWN UP Audio Level Control Front panel vary audio encode level with VU meter display Power Requirements 12Volt DC 4A provided with product via 4PIN connector Pin 1 Ground Pin 4 Hot 1 Non Captive UL CE Linecords are provided with unit for 110 220 Volt AC Operation Certifications Converter FCC CE External Power Unit UL CSA Dimensions Weight 3 5 H 2RU x 11 D x 19 W EIA Rackmount 8 5 Lbs Less Shipping Carton Operating Temp 32 F to 110 F 0 C to 43 C Operating Humidity 10 to 85 Non Condensing Storage Temperature 40 F to 150 F 40 C to 65 C Page 2 800 898 0759 845 339 9555 2000 Sterling Road Mount Marion NY 12456 www lairdtelemedia com pU LTM 6000D ALL FORMAT TRANSCODEH FRONT PANEL FEATURES You will notice that for such a powerful device the front panel incorpor
17. n Linear Editors NLEs have to see a live DV DEVICE in order to properly initialize the software The LTM 6000D will be identified as a PHILLIPS DV DEVICE depending on your operating system and software DO NOT HOT CON NECT IEEE1394 FireWire devices This can cause damage to your device and the LTM 6000D Be certain that the device is turned off before inserting or removing connections In the case of computer based NLEs it is advisable that the operating software such as edit software be offline or exited before any connections are made Page 6 800 898 0759 845 339 9555 2000 Sterling Road Mount Marion NY 12456 www lairdtelemedia com AGI LTM 6000D ALL FORMAT TRANSCODER TELE 4 Using The LTM 6000D with WINDOWS Your DV equipment such as a PC may be equipped with an compatible FireWire card Assuming all connections are proper the PC will recognize the LTM 6000D as new hardware as soon as it is initialized The LTM 6000D will be listed as a PHILLIPS DV Device Make certain that you have entered the proper Windows system compatibility selection from your Menu for Windows 98 2000 NT and XP To verify that your LTM 6000D is operating as a basic DV conversion device you can connect a video and audio analog signal to the LTM 6000D and follow the setup for DV ENCODE Converting Analog to DV from your Windows 2000 or XP desktop double click on MY COMPUTER The window will open and you should see the LTM
18. n be hor izontally and Subcarrier timed for perfect house lock There is an additional provision for vertical offset compensation which is a typical prob lem found in digital processing equipment DV Systems The LTM 6000D is a industry standard IEEE1394 system which operates in DV DVCAM for NTSC and DVCPro25 for PAL RS422 Machine Control A 9 Pin D Sub machine control port is provided for NLE machine control via FireWire IEEE1394 This system will provide standard SONY RS422 control protocol without the need for any external equipment This control system is a pass through protocol and simply passes the commands that are on the FireWire port and converts them to RS422 serial The standard list of RS422 commands which are translated are listed below SLOW FORWARD 2X CUE SLOW BACKWARD 2X STEP FORWARD FAST FORWARD 10X STEP BACKWARD FAST REWIND 10X RECORD EDIT RECORD PAUSE Page 7 800 898 0759 845 339 9555 2000 Sterling Road Mount Marion NY 12456 www lairdtelemedia com pU LTM 6000D EDTA ALL FORMAT TRANSCODER TELE GC Time Code The LTM 6000D will read and decode the time code stream from the RS422 data Both LTC and VITC time code can be read as well as interpolated between both formats An asterisk will display on the lower right corner of the LCD panel that confirms that Time Code is being read and processed RS232 Commands A 9pin D Sub port is provided for two functions The first is the p
19. r panel only Do not plug the product into an overloaded electrical outlet This may result in fire or electrical shock Object Ingress and Liquid Entry Never insert or push sharp metal objects into the product or use such devices for an attempt at opening or servicing the product Servicing should be referred to a trained and qualified technician only Do not allow liquid of any type to enter the unit Do not allow the unit to be submersed in water as this may cause a shock hazard A trained qualified technician should perform all servicing of the unit There are no serviceable components within the unit for user access CE All Laird Products are Manufactured in the USA by Laird Telemedia Mount Marion NY FireWire Apple and G4 are registered Trademarks of Apple Computer Inc Page 16 800 898 0759 845 339 9555 2000 Sterling Road Mount Marion NY 12456 www lairdtelemedia com AGI LTM 6000D ALL FORMAT TRANSCODER TELE lt 17 800 898 0759 e 845 339 9555 e 2000 Sterling Road Mount Marion NY 12456 e www lairdtelemedia com PP LAIRD TELE EDIA GC 2000 Sterling Road Box 720 Mount Marion NY 12456 800 898 0759 5 845 339 0231 wwwWw lairdtelemedia com
20. river and the connection integrity may be compromised 3 Do Not switch between DVCam and DVCPro in Pal while the Xpress DV application is open 4 Digital Cut AVID XPress DV does not allow mixed clips coming from DVCam or DVCPro in one project it comes up with an error message 5 When controlling a VTR through RS 422 directly from AVID via a serial cable connected to the PC MAC the Firewire Control in the Deck Configuration MUST be disabled deleting the Deck on the Firewire OHCI chan nel The Conversion direction must be set manually directly at the converter This must also be done when using no deck control Failure to do this will result in AVID changing the DECODE and ENCODE mode on the LTM 6000D 6 During digital cut or previewing clips in the bin the record Window must be closed Otherwise AVID XPress DV tries to switch the device on the firewire port that is not available this causes a delay from up to 5 seconds before the playback starts 7 The desktop play delay should be set to 13 15 frames for Pal depending on the speed of the computer 8 Be certain to check in the Audio Tools of AVID XPress DV the direction of the Audio channels During Record there must be an input and during Preview or Digital Cut there must be an output Using The LTM 6000D with Final Cut Pro HD Version 4 5 When using the LTM 6000D with Final Cut Pro HD Version 4 x you must set the LTM 6000 OS setting to WINXP 98 rather than the instructed DV Deck sett
21. rovision for system upgrades and firmware debugging The LTM 6000D is designed with the very latest in on board programmable software technology that allows updates changes and re programming via the RS232 port without having to open the device This gives the product high field reliability and serviceability by reducing the need to return the unit to the manufacturer for compatibility upgrades and improvements The 5232 port is also used to remotely control the LTM 6000D and provide signal processing PROC AMP features The RS232 port uses standard 9pin computer serial cables and can be operated up to 100 feet with proper shielded serial cable The control software runs in Windows and can be downloaded free of charge from the LAIRD website Stand Along Signal Transcoding Operations The LTM 6000D is designed around a highly advanced signal processing block of technology Utilizing the latest in firmware based semi conductors the LTM 6000D is built to perform as a stand alone signal processor and converter for analog and digital signals There is no need to connect a DV signal or device to convert between SDI AES and analog The product is designed to output all formats once a particular format has been selected as the input signal We refer to this as FULL TIME CONVERSION For example If you choose to convert SDI and AES EBU signals to component then the LTM 6000D will also output Composite YC and Balanced Audio as well The LTM 6000D will provid
22. t DOWN Line Number UP DOWN UP DOWN UP DOWN UP DOWN 127 V0 0 On 13 15 to to or or HO 128 V0 7 Off 16 18 or 20 22 DECODE These options appear only when Studio Genlock is ON NExT ENTER NExT To ENTER NExT TO ENTER NEXT TO ENTER DV Studio Subcarrier Horizontal sms LOWE lt DOWN System DOWN Genlock DOWN Phase Offset lt DOWN Offset Pixel UP DOWN UP DOWN UP DOWN UP DOWN DV DV CAM On Ph 0 H0 127 or or to to DVC Pro 25 Off Ph 255 HO 128 ENCODE Page 11 800 898 0759 e 845 339 9555 e 2000 Sterling Road Mount Marion NY 12456 e www lairdtelemedia com NExT ENTER LTM GOOOD ALL FORMAT TRANSCODER These options appear only when Output H ONLY Timecode is ON NEXT TO ENTER Next TO ENTER s Frame Time Code E Screen UP Offset UP gt Display UP gt E UP gt DOWN gt 1020 DOWN DOWNJ UP DOWN DISPLAYS THE UP DOWN UP DOWN Offset 4 CURRENT Yes Yes to Time CODE or or Offset 4 ON THE LCD No No DECODE This option appears This option appears only when Studio only when Input Genlock is ON Timecode is ON Next TO ENTER Next TO ENTER Next TO ENTER Vertical Offset Input Time UP gt UP gt lt DOWN Lines lt
23. tput A B Composite Video Output A B YC Video Output A B Component Y Output A B Component B Y Output A B Component R Y Output A B Looping Genlock Input AES EBU Audio Output Balanced Audio Output Ch1 A B Balanced Audio Output Ch2 A B RS232 Remote Control and Update Port RS422 Machine Control 12V DC Power Input To familiarize yourself with the menu functions it is advisable that you simply plug in the power supply and power up the unit without any devices connected The LCD display will illuminate and then cycle through its internal diagnostic functions After this is complete the factory default mode setting of DV DECODE will be displayed on the LCD By pressing the NEXT button you will begin the function select operations The LCD will display each function as you advance through the menu Study the menu tree on the next page to familiarize yourself with the LTM 6000D functions There are a few functions that merit special attention PAL and NTSC have some special selections that are unique to each other This is outlined in the menu tree In GENLOCK ON there are selections for three related operations Horizontal Phase Subcarrier and Vertical Offset Page 4 800 898 0759 845 339 9555 2000 Sterling Road Mount Marion NY 12456 www lairdtelemedia com pU LTM 6000D EDTA ALL FORMAT TRANSCODER TELE GC FAMILIARIZING YOURSELF WITH THE LAIRD LTM 6000D The LAIRD LTM 6000D represents the finest
Download Pdf Manuals
Related Search