User`s Manual CNPS 5X
Contents
1. 775 ZALMAN COM 3 Align the Clip Support to the motherboard and fasten with the Pushpins Clear off any particles or residue from the CPU s surface Then spread a thorough layer of Thermal Grease on the CPU and the base of the cooler ZALMAN COM Completely unfasten the 2 bolts already assembled on the clip and adjust the position to fit the Intel socket When reassembling the bolt be sure to assemble only half way of the total length Location of Intel Socket bolts Install the cooler on the Clip support as shown in the picture and connect the lug slot of the clip on to the lug on the clip support Then fasten the bolts on each side a few turns at a time a T Connect the cooler s 4 pin connector to the motherboard s CPU Fan header EN 0008 Gs Caution The PWM fan s operation will vary depending on the motherboard s BIOS settings ZALMAN COM 2 AMD Socket AM3 AM2 AM2 Installation Clear off any particles or residue from the CPU s surface Then spread a thorough layer of Thermal Grease on the CPU and the base of the cooler Completely unfasten the 2 bolts already assembled on the clip and adjust the position to fit the AMD socket When reassembling the bolt be sure to assemble only half way of the total length Location of AMD Socket bolts Install the cooler on the Clip support as shown in the picture and connect the lug s2. CNPS 5X Intel Socket 1155 1156 775 CPU Core i7 Core i5 Core i3 Core 2 Extreme Core 2 Quad Core 2 Duo Dual Core Pentium Pentium D Pentium 4 Celeron D AMD Socket AM3 AM2 AM2 CPU Phenom II Phenom Athlon II Athlon X2 Athlon FX Athlon Opteron Dual Core Opteron Sempron To ensure safe and easy installation please read the following precautions www ZALMAN com 1 1 Q 1 Precautions 1 2 8 10 Avoid inserting objects or hands into the fan while it is in operation to prevent product damage and injuries Do not ingest the Thermal Grease and avoid its contact with skin and eyes If contact is made with skin wash off with water If ingested or irritation persists seek medical attention To prevent possible injuries gloves must be worn while handling this product Excessive force exerted on the fan may cause damage to the fan and or system Use and keep product away from reach of children Check the components list and condition of the product before installation If any problem is found contact the retailer to obtain a replacement During transportation of the system the cooler must be removed Zalman is not responsible for any damages that occur during the transport of a system Product design and specifications may be revised to improve quality and performance Enable PWM function in BIOS settings after installation Disclaimer Zalman Tech Co Ltd is not responsible
3. for any damages due to external causes including but not limited to improper use problems with electrical power accident neglect alteration repair improper installation or improper testing Q 2 Specifications Sa a 127 L X 64 W X 134 H mm Noise Level 20 32dBA 15 Input Voltage Bearing Type Enter Bearing RPM 1 400 2 800rpm 10 PJ exe PWM Control Auto Restart J 3 Components Cooler Backplate Manual User s Manual Thermal Grease p 4 Installation Requirements 1 Space Requirements The cooler s installation requires an unobstructed space of 130mm width 65mn length and 135mm height with the CPU as a central reference point Please check if components such as ODDs and PSU protrude into the required space 2 Air Guide Removal Air guides on enclosures must be removed before the cooler s installation since they protrude into the cooler s required space ZALMAN COM 3 Cooler Orientation As shown in the diagram below it is recommended that the cooler be installed so that air flows from the cooler toward the enclosure s rear exhaust fan to be released X Recommended cooler orientation may differ according to the motherboard model Q 5 Installation 1 Intel Socket 1155 1156 775 Installation Install the Clip Support to the motherboard according to the socket type See diagram Socket 1155 1156 Socket
4. lot of the clip on to the lug on the clip support Then fasten the bolts on each side a few turns at a time ZALMAN COM Connect the cooler s 4 pin connector to the motherboard s CPU Fan header at eS o Caution The PWM fan s operation will vary depending on the motherboard s BIOS settings ZALMAN COM
Download Pdf Manuals
Related Search