Home

User Manual: 21-slot cPCI Crate

image

Contents

1. 2 2 _ Site Considerations The CC121 is designed to be used either in a 19 inch instrument rack or in a bench top configuration It is delivered in the bench top configuration with four feet screwed into the holes provided on the bottom of the crate NOTE With the feet in the bench top configuration the crate height is slightly more than the standard 9U In order to use the crate in a 19 inch instrument rack the user must unscrew the feet and to avoid losing them screw them back into the stocking holes provided in the lower part of the rear panel CAUTION Keep other equipment a minimum of 75mm 3in away from the air inlets and outlets 2 3 Mains Power 2 3 1 Connecting to AC Mains Power CAUTION Make sure that the main power switch is in the 0 position OFF before connecting the power cord to AC mains power The power supply is universal which means that the crate can connect to all standard worldwide input voltages Attach input power through the rear panel AC Line inlet using the appropriate power cord supplied Refer to the paragraph 7 Packaging and Handling for the power cord specification 2 3 2 Fuses WARNING The value of the F1 and F2 power line fuses depend of the AC power input voltage For safety reasons please follow the instructions shown in the table below Disconnect the power cord before replacing the fuses The F1 and F2 power line fuse holders are located on the rear panel 85
2. Before connecting the crate to a power source read th N WARNING Main Power Switch Modules and Power Supply Cooling Air Inlets E X o D E S 9 o gw ur aN 22 xc lt o N o 0 g Q 2 c 29 Lo Four Removable Feet Front view of the CC121 1 igure Conductive Surface odule Cooling Air Outlets F1 Fuse Holder F2 Fuse Holder 4 Universal AC Input IEC320 C14 Inlet Terminal Quauaadaaaaaaaaaaaaauaaaa e ii lt A ajajaja jajajajaja majaan amaa ma n o arw ya aya aaye a a a ayaan CIMA LEY CAMYAPARWOADYOGHOOODXOBEAMMAPADDXOmO _ OCHDYAULXGCWATYATADYOYOGOUVAMAOYDMAVACACWAVAUCADICOYNAVAUAAUMO Removable Feet Storage Four Hole M4 Size Y poem CAO Power Supply Cooling Air Outlets Conductive Surface Rear view of the CC121 Figure 2 Page 8 of 19 Agilent Acqiris 21 slot cPCI Crate User Manual gt
3. 230V AC 900W 115VAC 3 3 0 1V 5 1 0 1V 12 15 0 15 12 15 0 15V Output Voltages 120A 400W 120A 600W 50A 600W 25A 300W RMS Ripple 0 1 or whichever is greater 20MHz bandwidth Peak to Peak Noise 1 or 50mV whichever is greater 20MHz bandwidth Dynamic Response lt 2 or 100mV 25 load step Maximum Output Currents Recovery Time To within 1 in lt 0 3msec All outputs are protected from short circuit and overload Automatic recovery 3 3V and 5V 122 134 12V and 12V 110 120 Turn OFF the crate to reset the Over Voltage Protection Over Current Protection Over Voltage Protection All outputs disabled when the power supply internal temperature exceeds safe operating range Automatic recovery Each output individually protected Turn OFF the crate to reset the Individual Protection Warning signal FAL 5msec before shutdown Thermal Protection 3 3 Slot Specifications Height 6U Width 20 32mm 0 8 in System Slot 20 Peripheral Slots Forced air circulation separated from the power supply cooling The airflow direction is from the front to the rear of the crate Slot airflow direction from the bottom to top of the modules Three 50 1 5 106 cfm axial fans Module Cooling System Typical 6 1 5 12 7 cfm Airflow per Slot Velocity 2 4 m s 480 lfm 70 cross section aperture Separated from the power supply thermal protection All power
4. 132 VAC 5x20mm slow blow fuse T 16A H 250V Acqiris PN EF011160A 190 264 VAC 5x20mm slow blow fuse T 8A H 250V Acqiris PN EF010800A For continued protection against fire hazard replace only with a fuse of the same type and correct rating 2 4 Installing CompactPCI Modules CAUTION Turn off the crate power before installing or removing CompactPCI modules NOTE The crate controller must be placed in the System Slot slot 1 located at the left of the crate The System Slot is identified with the number 1 surrounded with a triangle All other modules are to be placed in the Peripheral Slots that are identified with their respective number surrounded with a circle NOTE If you want the driver to automatically recognize the crate as a CCI21 you should put at least one Acqiris acquisition module into one of the last 7 slots If you do not do this you can use the Geographical Mapper application discussed in the User Manual to create an AqGeo map file NOTE If you want to chain other CC121 crates to this one please put the additional Acqiris ICxxx or MXI 3 18335 modules in slots 2 4 of this upstream crate NOTE The 21 crate accepts PXI modules but does not provide PXI specific features Local Bus Trigger Bus System Reference Clock 2 4 1 Installing 6U modules Install a module into the crate slot by first placing the module s card edges into the front module guides top and bottom Place both injector ejecto
5. 3 5 Environmental 3 5 1 Environmental Specifications Operating Temperature 0 to 45 C Storage Temperature 40 to 85 C Operating Relative Humidity 5 to 95 non condensing Operating Altitude 3000 m 3 5 2 Safety In accordance with Council Directive 73 23 EEC Low Voltage Safety IEC 61010 1 2001 EN61010 1 2001 in accordance with the European Council Low Voltage Directive 2006 95 EC Conformity Canada CSA C22 2 No 61010 1 2004 USA UL 61010 1 2004 Installation Category II Pollution Degree 2 safety Class 1 3 5 3 EMC Immunity amp Emissions Complies with European EMC Directive 2004 108 EC e IEC EN 61326 2 1 e CISPR Pub 11 Group 1 class A e AS NZS CISPR 11 ICES NMB 001 This ISM device complies with Canadian ICES 001 Cet appareil ISM est conforme la norme NMB 001 du Canada CISPR 11 2003 EN 55011 2007 Class A Groupl IEC 61000 4 2 2001 EN 61000 4 2 4 4 kV contact air IEC 61000 4 3 2002 EN 61000 4 3 3 V m 80 2000 MHz 1 V m 2 2 7 GHz IEC 61000 4 4 2004 EN 61000 4 4 0 5 kV signal lines 1 kV power lines IEC 61000 4 5 2001 EN 61000 4 5 0 5 kV line line 1 kV line ground IEC 61000 4 6 2003 EN 61000 4 6 3 0 15 80 MHz 10096 dip 1 cycle 6096 dip 10 cycles 3096 dip CeCe een guerre ee aah 25 cycles 100 interruption 250 cycles The product was tested in a typical configuration with Agilent Technologies test systems User Manual Agilent Acqiris 21 slot cPCI Crate Pag
6. 9 219 duo RC 9 2 9 1 Xonnecting to AC Mans POWOL seno ooo vete eM 9 Dis EMITIR 9 2 4 Installing CompactPCl Modules vx 9 2 41 installing gU modules e d p t tiva e d lu edenda At de 9 21 2 AMS TAM iaceo eb on s benda 10 245 PIOS MY c dete vise eoe 10 3 SPECIFICATIONS c 11 3 CALE CS EN EE 11 3 2 ROWSE SUDDEP sl Mu tu 11 Izl Input specications oe cee aus 11 92 2 DC OUIDUIS SDecIHCatloNisun ete edebat te Dr Quare oi dep 12 Bo Slot Spec Canons RT TT OE 12 3 4 BACK ANC REN A E a NS 13 Scl Backplane Specilications i ceo treni Gr biet De Qe cede eri ive e EDO e Eds 13 DADs UPOWOLSUDDIV 14 Connector 15 3 5 Environmettal s S S E 16 33 1 Epvronmental Speci cation Seest dale ose EN Met 16 SO EA 16 93 3 Immunity L EMISSIONS rie ect 16 3 6 E 17 3 5 1 Mechanical SpecttiCallOBls aeneus ti rod tubo E Mi ed 17 90 2 3DITHEDSTODS Sopas Us p etd tas Adde mute 17 4 APPENDICE
7. it from moving in the shipping container Styrene pellets can also cause equipment damage by generating static electricity or by lodging in fan motors 1 12 Maintenance The CC121 crates do not require any maintenance There are no user serviceable parts inside 1 13 Cleaning WARNING Always power off the crate and disconnect the power cord before cleaning the crate Cleaning procedures consist only of exterior cleaning Clean the exterior surfaces of the crate with a dry lint free cloth or a soft bristle brush If any dirt remains wipe with a cloth moistened in a mild soap solution Remove any soap residue by wiping with a cloth moistened with clear water Do not use abrasive compounds on any part of the crate CAUTION Avoid getting moisture inside the crate during exterior cleaning Use just enough moisture to dampen the cloth Do not wash the connector and switch Cover these components while cleaning the crate Do not use chemical cleaning agents they may damage the crate Avoid chemicals that contain benzene toluene xylene acetone or similar solvents 1 14 Disposal and Recycling Electronic equipment should be properly disposed of Acqiris Digitizers and their accessories must not be thrown out as normal waste Separate collection is appropriate and may be required by law User Manual Agilent Acqiris 21 slot cPCI Crate Page 7 of 19 INSTALLATION 2 Configuration 2 1 hapter and the paragraph 1 5 IS
8. supply outputs are shutdown when the slot environment exceeds safe operating temperature 60 C Warning signal FAL lt 4msec after the beginning of the shutdown Slots Thermal Protection Automatic recovery Per Slot Current Capacity See paragraph 3 4 1 Working Currents Maximum Module Weight 1 5 kg 3 3 Ib User Manual Agilent Acqiris 21 slot cPCI Crate Page 12 of 19 Slot Numbering Convention 4 11 18 s 3 4 Backplane 3 4 1 Backplane Specifications CompactPCI PICMG 2 0 R3 0 Conformity UL recognized 2 Slots 1 System Slot to left 20 Peripheral Slots Three segments of seven slots linked with two Configuration transparent bridges plugged on the rear of the backplane the slots are available for the application with complete access from the front side Coding Keys 5V coding key assembled brilliant blue Connectors P1 Module A and P2 Conforms to IEC917 and IEC 1076 4 101 Module B UL 94VO rated 1 5 25 max per contact 1 2A 9 50 C Power supply contacts per slot connectors P1 and P2 3 3V 10 contacts 5V Pl 8 contacts 12V Pl 1 contact 12V Pl 1 contact V I O Pl 5 contacts P2 6 contacts GND Pl 14 contacts P2 18 contacts Working Currents User Manual Agilent Acqiris 21 slot cPCI Crate Page 13 of 19 3 4 2 Power Supply Status The Derating DEG and Supply Fail FAL are implemented only for the System Slot Levels TTL levels require pull up resisto
9. the box lists optional equipment you can order from us and describes the warranty and repair return procedure Chapter 2 INSTALLATION describes how to prepare and operate your CC121 crate Chapter 3 SPECIFICATIONS gives complete technical specifications of your CC121 crate Chapter 4 APPENDICES gives specifications and assembly instructions supplied with the optional equipments 1 4 Conventions Used in This Manual The following conventions are used in this manual This icon to the left of text warns that an important point must be observed WARNING Denotes a warning which advises you of precautions to take to avoid being electrically shocked CAUTION Denotes a caution which advises you of precautions to take to avoid electrical mechanical or operational damages NOTE Denotes a note which alerts you to important information Italic Italic text denotes a warning caution or note Bold Italic Bold italicized text is used to emphasize an important point in the text or a note 1 5 Disclaimer and Safety WARNING The CC121 crate contains voltage hazardous to human life and safety and is capable of inflicting personal injury For your safety before undertaking any troubleshooting or maintenance procedure read carefully the WARNING and CAUTION notices Crate Grounding The 121 crate requires a connection from the premises wire safety ground to the CC121 chassis ground to minimize shock hazard This crate is designed with a
10. three position IEC320 C14 plug that connects the earth safety ground line to the chassis ground A power cord with protective safety ground conductor must be used The earth safety ground line must be always connected during use of this equipment To minimize shock hazard make sure your electrical power outlet has an appropriate earth safety ground that is connected whenever you power up the crate Live Circuits Operating personnel must not remove protective covers when operating or servicing the CC121 crate Adjustments and service to internal components must be undertaken by qualified personnel During service of this User Manual Agilent Acqiris 21 slot cPCI Crate Page 4 of 19 product the mains connector to the premise wiring must be disconnected Dangerous voltages may be present under certain conditions use extreme caution Explosive Atmosphere Do not operate the crate in conditions where flammable gases are present Under such conditions this crate is unsafe and may ignite the gases or gas fumes Part Replacement Only service this crate with parts that are exact replacements both electrically and mechanically Installation of parts that are not exact replacements may cause harm to personnel operating the crate Furthermore damage or fire may occur if replacement parts are unsuitable Lifting and Carrying An empty U1091AC21 CC121 crate weighs 21 7 kg 47 6 Ib A fully loaded crate could weigh up to 53 kg 117 16 Thus it is n
11. 0000000000000000000000000E6800080000000000 GS 086056 500800800 506506506 56 566 S66 506 50655 S66 S86 505865668668 EEEEOSEBEBEEBEPEBEEEBEEBEECDEEEBEEDBBHEOEDBEEEDOEEBEDEEBOBPBEBEBBEEBBBBEDBEBEEDEBEFEEECIEEEEGEEBEEGEEDECEEEC EE mjm Iw I CN Y 40 40 ru Bi A A Four Screwed Removable Feet M4 Size IT User Manual Agilent Acqiris 21 slot cPCI Crate Page 17 of 19 4 APPENDICES 4 1 U1092A C01 U1056A A10 XC100 6U to 3U Slot Adapter Specifications and Assembly Instructions SPECIFICATIONS The XC100 6U to 3U slot adapters are specially designed for use with Acqiris CompactPCI crates The XC100 allows the use of 3U CompactPCI modules in any vacant 6U slot CAUTION The XC100 6U to 3U slot adapter must be installed prior to inserting any 3U CompactPCI module into any Acqiris CompactPCI crate The XC100 assures proper mechanical alignment when inserting a 3U module and protects the crate s backplane connectors from damage In addition the XC100 provides the function of a blanking panel to completely close the vacant slot This function is essential to guarantee EMC shielding and adequate cooling ASSEMBLY INSTRUCTIONS 1 Insert the XC100 into the left part of the chosen 6U slo
12. 19 1 11 To package the instrument for shipping Transport amp Shipping Step 1 Place the instrument in its original packaging materials 2 Surround the instrument with at least 3 to 4 inches 8 to 10 cm of its original packing material or bubble pack to prevent the instrument from moving in its shipping container 3 After wrapping it with packing material place the instrument in its original shipping container or a strong shipping container that is made of double walled corrugated cardboard with 159 kg 350 Ib bursting Notes f the original packaging materials are not available use a professional packaging service Contact your Agilent Service Center for more information The shipping container must be large and strong enough to accommodate your instrument and allow at least 3 to 4 inches 8 to 10 cm on all sides for packing material strength 4 Seal the shipping container securely with strong nylon adhesive tape 5 Mark the shipping container FRAGILE HANDLE WITH CARE to help ensure careful handling 6 Use the address obtained from your Agilent Technologies Service Center 7 Retain copies of all shipping papers CAUTION Damage can result if the original packaging materials are not used Packaging materials should be anti static and cushion the instrument on all sides NEVER USE STYRENE PELLETS IN ANY SHAPE AS PACKAGING MATERIALS They do not adequately cushion the instrument or prevent
13. I DI DI Q Z Q 63 GND 5 1 0 C BE QIQ QI 4 ND ND ND ND 5V REQ64 ENUM ND 4 GND 1 V I O ACK64 ND GND 10 BRSVP2B4 7 2 2 a 2 33v ADA ADDB 2 ND 2 GND GND 33V ADI ND 33V ADIS M 6EN ND 20 AD I2 0 10 ND 3 3V AD 15 AD 14 GND AD 13 GND SERR GND 3 3V SDONE SBO PERR P1 C Z 4 GND REQ4 CLK2 CLK3 SYSEN GNT2 Q Q 1 J Q Z J J m 3 3 V Q Z Q Z 216 lt 0 5 3 2 Z Q J Nn Q Z J J Q JU Z 9 GND IDSEL GND ADI 2 GND 8 GND GND vao ADDS 04 GND 5 GND 33V GND BRSVPIA4 INTA a T QIQ Z J Q INTB INTC INTD 5V 12V TRST Q TCK 5V GND Notes 1 All pins are medium length level 2 except on the connector P1 pin C16 which is long level 3 and D15 which is short level 1 2 The following positions of connector P2 are implemented only on the System Slot A1 3 A19 21 B2 B19 21 C1 3 C15 17 D1 3 D15 D17 E1 3 E15 E17 3 Connector P2 pin C2 is connected to GND at the System Slot only User Manual Agilent Acqiris 21 slot cPCI Crate Page 15 of 19
14. S wen 18 4 1 U1092A CO01 U1056A A10 XC100 6U to 3U Slot 18 4 2 U1092A C02 U1056A A11 XC200 6U Filler 1 19 User Manual Agilent Acqiris 21 slot cPCI Crate Page 3 of 19 1 OUT OF THE BOX 1 1 Message to the User Congratulations on having purchased an Agilent Technologies Acqiris product U1091AC21 CC121 21 slot 6U crates use the highest quality components and high output power supplies in order to maximize system performance and reliability These universally applicable CompactPCI crates are carefully designed to yield high performance test systems for bench lab and manufacturing test applications 1 2 Before Using Your Crate This User Manual describes the features of the CC121 crate and contains information for your safety about configuring the crate installing the modules and operating the system CAUTION The AC power input line is fully protected by two fuses the value of which depends on the AC input voltage For safety reasons the user must check that those values comply with the input voltage used before connecting the crate to the AC mains power For further information please refer to the paragraph 2 3 2 Fuses 1 3 Organization of This Manual This manual is organized as follows Chapter 1 OUT OF THE BOX gives information you must know prior to using CC121 crates lists the contents of
15. UsER MANUAL AGILENT ACOIRIS 21 sLoT CPCI CRATE GE Agilent Technologies Manual Part Number U1092 90019 Edition D RevB June 2010 The information in this document is subject to change without notice and may not be construed in any way as a commitment by Agilent Technologies Inc While Agilent makes every effort to ensure the accuracy and contents of the document it assumes no responsibility for any errors that may appear All software described in the document is furnished under license The software may only be used and copied in accordance with the terms of license Instrumentation firmware is thoroughly tested and thought to be functional but it is supplied as is with no warranty for specified performance No responsibility is assumed for the use or the reliability of software firmware or any equipment that is not supplied by Agilent or its affiliated companies You can download the latest version of this manual from http www agilent com by clicking on Manuals in the Technical Support section and then entering a model number You can also visit our web site at http www agilent com find acqiris At Agilent we appreciate and encourage customer input If you have suggestion related to the content of this manual or the presentation of information please contact your local Agilent Acqiris product line representative or the dedicated Agilent Acqiris Technical Support SUPPORT agilent com Acqiris Product Line Informa
16. and Repair Return Procedure Assistance and Support Agilent acquired Acqiris SA and its product lines in December 2006 Please contact your nearest Agilent Service Center before returning any product for repair You can find information about technical and professional services product support and equipment repair and service on the Web see http www agilent com find service or http www agilent com and after selecting your country click on Contact Us The service center will ask for your name company phone number and address the model and serial numbers of the unit to be repaired and a brief description of the problem Before issuing a Service Order the service center may ask you to communicate with us by phone or eMail so that we can learn as much as needed about the problems observed If a unit returned under guarantee is found to be working normally and this procedure was not followed we reserve the right to charge you for the work done For your nearest customer support center please contact Acqiris Technical Support ACQIRIS_SUPPORT agilent com or come visit our web site at http www agilent com find acgiris Alternatively contact Acqiris at 1 800 829 4444 in the USA 41 22 884 32 90 in Europe or 61 3 9210 2890 in the Asia Pacific region The Agilent Support Centers can also help redirect you for any questions concerning the installation and operation of your equipment User Manual Agilent Acqiris 21 slot cPCI Crate Page 6 of
17. e 16 of 19 3 6 Mechanical 3 6 1 Mechanical Specifications Overall Dimensions Enclosure Material and Finish Handles Bus Bars Card Guides 3 6 2 Dimensions 19inch 483 483mm 19 in 440mm 17 32 in including the handles 399mm 15 71 in 9U 411mm 16 18 in including the feet Steel sheet Zinc plated Outward painted Aluminum extrusion Clear chromated Aluminum sheet Clear chromated Outward painted Aluminum Black anodized Copper Nickel plated Molded plastic UL 94V0 rated 360 B p pose Slot D D Peripheral Slots eo OG O O 6 O O O O O O o O o o O O O0 e o o o o e ec D ki J cud a DO ANDI BST D0 os jal OBO OOOOG00000 O0 oo a It q OQOOODO0 80 OOO MO0000 CICD CS CIC CS ORR OU CCS QOOOO000 000000000 DODD GDR OO00
18. ecessary to remove the modules before moving or carrying the mainframe and either two persons using two handles each or a mechanical lift are needed to manipulate the empty crate WARNING If an instrument handle is damaged you should replace it immediately Damaged handles can break while you are moving or lifting the instrument and cause personal injury or damage to the instrument Modification Do not modify any part of the crate from its original condition Unsuitable modifications may result in safety hazards 1 6 Warning Regarding Medical Use The CC121 crates are not designed with components and testing intended to ensure a level of reliability suitable for use in treatment and diagnosis of humans Applications of these crates involving medical or clinical treatment can create a potential for accidental injury caused by product failure or by errors on the part of the user These crates are not intended to be a substitute for any form of established process or equipment used to monitor or safeguard human health and safety in medical treatment WARNING The modules discussed in this manual have not been designed for making direct measurements on the human body Users who connect an Acqiris module to a human body do so at their own risk 1 7 Packaging and Handling After carefully unpacking all items inspect each to ensure there are no signs of visible damage Check to make sure that all hardware and the switch are undamaged Inspect
19. handles into place 3 Tighten both scews to lock the XC200 into place and insure proper grounding of the frame QU 0 Segoe ae 2 di BAT VA gU TU E i E ite Ur P A E eiii 5 0 User Manual Agilent Acqiris 21 5101 cPCI Crate Page 19 of 19
20. ing screws to lock the module into place and insure proper grounding of the frame 2 4 3 Installing Filler Plug in CAUTION The CCI21 crate should not be used without closing all unused or empty slots To guarantee EMC performance and adequate cooling install an optional XC200 Filler Plug in or other filler panels conform to IEEE1101 10 into all unused slots Tighten both captive mounting screws to lock the panel into place and insure proper grounding of the frame NOTE Refer to the appendix 4 2 U1092A C02 U1056A A11 XC200 6U Filler Plug in Specifications and Assembly Instructions User Manual Agilent Acqiris 21 slot cPCI Crate Page 10 of 19 3 SPECIFICATIONS 3 1 Main Features The main features of the CC121 CompactPCI crate include 19 inch rack mount crate 9U high 21 vertical slots with System Slot at the left and 20 Peripheral Slots CompactPCI PICMG 2 0 R3 0 6U and 3U module compatibility The Backplane has three segments of seven slots linked with two CompactPCI bridge modules These bridges are plugged on the rear of the backplane and all the slots are available for the application with complete access from the front side The Backplane is equipped with P1 and P2 connectors with V I O to 3 3 V and 3 3 V coding keys assembled A CompactPCI module must be used with the optional XC100 Slot Adapter The crate accepts PXI modules but does not provide PXI specific features Optimized cross flow air circulation P
21. ower supply and module slots are cooled separately and fully protected against over temperature Meets the IEEE 1101 10 standard for EMC compatibility and optimized cooling Front panel Power Switch Quality power supply with universal AC input power factor correction auto voltage and auto frequency ranging It is capable of delivering 1200W 230V AC or 900W 115VAC Derating DEG and Supply Fall FAL signals provided from the power supply to backplane System Slot P2 connector Handles on the front and rear sides for easy handling Removable feet for bench top applications and in rack mount applications four M4 size holes are provided on the rear panel for their storage 3 2 Power Supply 3 2 1 AC Input Specifications AC Input Voltage Range Universal Input 110 120 220 240 V Input Frequency Range Auto Frequency Ranging 50 60 Hz Maximum Input Power 1900W 30msec minimum full load Holdover Storage Independent of AC input voltage F1 and F2 located on the rear panel AC Input Fuses 85 132V Slow Blow T 16A 250V 5x20mm 190 264V Slow Blow T 8A 250V 5x20mm AC Input Inlet IEC320 C14 Internal Input Fuse F1 Type KLK25 25A 600V manufactured by Littelfuse Three internal DC Fans The airflow direction is from the Power Supply Cooling front to the rear of the crate User Manual Agilent Acqiris 21 slot cPCI Crate Page 11 of 19 3 2 2 DC Outputs Specifications Maximum Usable Power 1200W
22. r handles in the open position and slide the module to the rear of the crate When User Manual Agilent Acqiris 21 slot cPCI Crate Page 9 of 19 you begin to feel resistance push simultaneously both injector ejector handles towards the center to plug the module into the backplane connectors of the crate Secure it by clipping the handles into place Tighten both front panel mounting screws to lock the module into place and insure proper grounding of the frame 2 4 2 Installing 3U modules CAUTION The XC100 6U to 3U Slot Adapter must be installed prior to inserting any module into the CC121 crate The XC100 is necessary to guide the 3U module and avoid damaging backplane connectors Insert the XC100 into the module guide of the top part of the 6U slot Turn the front panel knob in the clockwise direction to fasten the slot adapter into place Tighten its front panel screw to insure proper grounding of the frame NOTE Refer to the appendix 4 1 U1092A C01 U1056A A10 6U to 3U Slot Adapter Specifications and Assembly Instructions Install a 3U module into the crate slot by first placing the module s card edges into the top and bottom guides Place the injector ejector handle in the open position and slide the module to the rear of the crate When you begin to feel resistance raise the handle to plug the module into the backplane connectors of the crate Secure it by clipping the handle into place Tighten both front panel mount
23. r to 5V ZkOhm on the System Controller Board Indicate that the power supply is beginning to derate its power outputs 1 Mains AC is accurate 0 to 1 2msec minimum after the DC outputs are accurate to 0 20msec minimum before FAL and DC outputs are shutdown DEG Mains AC accurate signal Indicate that a DC output from the power supply has a failure All DC outputs are accurate to 1 Imsec maximum before the DC outputs are accurate to 0 4msec maximum after the start of the DC output shutdown FAL Global DC outputs accurate signal User Manual Agilent Acqiris 21 slot cPCI Crate Page 14 of 19 3 4 3 Connector Pinouts C Connector a B C 2 GND GA4 GAI CLK6 RSV 2 CLKS GND GND RSV BRSVP2A18 GND BRSVP2A17 REQ6 BRSVP2A16 GND BRSVP2A15 REQS ADI35 GND P2 ADI 2 45 44 AD 52 ADISI ADIS6 7 ADI GND GND GND 5V 0 AD 4 GND AD 6 AD 9 GND DI AR GAO RSV RSV ND RSV ND BRSVP2E18 ND GNT6 ND BRSVP2E16 ND GNT5 ND AD 32 ND AD 36 ND AD 39 ND AD 43 ND 46 ND AD 50 ND AD 53 ND ADI 57 ND AD 60 ND PAR64 6 GNT4 REQ3 REQ2 Q Q Z J ND Q Z u Q J i QIQ Z JU G Q 37 z Q 2 J 38 42 D GND QIQ JU GND AD 49 GND Q i Q DI DI DI AD DI GND ADIS9 ADISS DI D
24. riate cooling 1 8 2 Filler Plug in An optional U1056A A11 XC200 Filler Plug in is available from Acqiris This 6U CompactPCI plug in width 1 slot meets the IEEE 1011 10 standard and implements the function of a filler panel that completely closes the front of the unused slots and reduces the cross flow air circulation This function is essential to guarantee EMC performance and appropriate cooling 1 9 Warranty All Agilent Acqiris Digitizer products are warranted to operate within specification assuming normal use for a period of at least one year from the date of shipment Units sold before April 2008 had three year warranties as do some more recent ones in case of doubt examine your invoice It is recommended that yearly calibration be made in order to verify product performance repairs replacement and spare parts are warranted for a period of 3 months Warranty extensions are available as an option In exercising this warranty Agilent will repair or replace any product returned to the Agilent service center within the warranty period The warranty covers all defects that are a result of workmanship or materials This excludes defects that are caused by accident misuse neglect or abnormal operation The purchaser is responsible for returning the goods to the nearest Agilent service center This includes transportation costs and insurance Agilent will return all warranty repairs with transportation prepaid 1 10 Warranty
25. rogram for the AC SC Analyzer products o the AcgirisLive application a demonstration program for our digitizer and averager products o the SSR Demo application a demonstration program for the Acqiris AP235 AP240 Analyzers User Manual Agilent Acqiris 21 slot cPCI Crate Page 5 of 19 o the Demo application a demonstration program for the Acqiris AP101 AP201 Analyzers o the TC Demo application a demonstration program for the Acqiris TC840 TC842 TC890 Time to Digital Converters o full installation procedures for use with Microsoft Windows National Instruments LabVIEW RT Wind River VxWorks IVI COM C and Linux software e For many products a declaration of conformity is still included However in an increasing number of cases the Declaration can be viewed at http www agilent pra com Optional equipment See the enclosed packing list 1 8 Optional Equipment 1 8 1 CompactPCI 6U to 3U Slot Adapter The optional U1056A A10 XC100 Slot Adapter is specially designed for use with Acqiris CompactPCI crates This CompactPCI slot adapter allows the use of modules in any vacant 6U slots The XC100 assures proper mechanical alignment when inserting a 3U module and protects the crate s backplane connectors from damage In addition the XC100 meets the IEEE 1011 10 standard and provides the function of a filler panel to completely close the half vacant slot This function is essential to guarantee EMC performance and approp
26. t 2 Turn knob in the clockwise direction to fasten the unit into place 3 Fasten screw to insure proper grounding of the frame AE UE 20 g d 0 B p g EA e al 10 AE ENNEN T SE TBBL AAAs ASE AXE SN NEN SENE YARN ATA N AN x VEXE TAX WAR RARARE Gs B f SEN SENSA RS TA NES BREE ES SES TAREE NENNEN EEA ATEN A User Manual Agilent Acqiris 21 slot cPCI Crate Page 18 of 19 4 2 U1092A C02 U1056A A11 XC200 6U Filler Plug in Specifications and Assembly Instructions SPECIFICATIONS The XC200 filler plug in is used to close vacant slots in Acqiris GU CompactPCI Crates CAUTION The XC200 filler panel is required to guarantee EMC shielding and adequate cooling Crates should not be used without closing all vacant front panel slots ASSEMBLY INSTRUCTIONS 1 Insert the XC200 in the chosen slot by holding the handles on each side 2 Gently push the XC200 into the slot and secure it by clipping the
27. the inner chassis for any possible damage debris or detached components If damage appears to have been caused in shipment file a claim with the carrier Also check that all the components received match those listed on the enclosed packing list Agilent cannot accept responsibility for missing items unless we are notified promptly of any discrepancies If any items are found to be missing or are received in a damaged condition please contact the Agilent service center or your local supplier immediately Retain the box and packing materials for possible inspection and or reshipment Verify that you have received the following items with your CC121 crate e Power cord Universal Europa 250V 10A CEE7 sht IEC320 C13 125V 15A NEMA 5 15 IEC320 C13 United Kingdom 250V 10A BS1363A IEC320 C13 250V 10A CIE 23 16 IEC320 250V 10A SEV1011 IEC320 e User Manual Agilent Acqiris 21 slot cPCI Crate e Acompact disc in an Agilent Technologies paper CD envelope that includes o 10 product User Manuals in electronic form 8 bit Digitizers 10 bit Digitizers 12 bit Digitizers Averagers Analyzers Signal Analyzers Streamer Analyzers Time to Digital Converters 3 5 and 8 slot CompactPCI Crates and the 21 slot CompactPCI Crate o l Programmer s Guide and 1 Programmer s Reference Manual o device drivers with sample software for different operating systems environments and languages o the Analyzer Demo application a demonstration p
28. tion USA 800 829 4444 Asia Pacific 61 3 9210 2890 Europe 41 22 884 32 90 Copyright Agilent 2010 User Manual Agilent Acqiris 21 slot cPCI Crate Page 2 of 19 CONTENTS 1 THE BOX erm 4 1 1 Message tothe ies dal esau taeda E 4 1 2 Betore Dsinp Y OUPE Pale ood sete etos erat ode aded eto ote 4 1 Organizationor dThis Manual dote tae Ua es rd Cu 4 1 4 Conventions Used in This Manual b Een a i a ape 4 1 5 Diselamier andis dfe studet 4 1 6 Warming Regarding Medical die esse teet hene e ia ve er que 5 1 7 Packaging and Handlime ancen A bu tu Hoa DR eut 5 1 8 Obuonal EquipHte HE 9 569 5 E tu totus E 6 1 8 1 to 3U Slot Adapter orent e tee err rtr eet eve 6 5 2 Fier PIUS tdeo ee 6 1 9 ON 6 1 10 Warranty and Repair Return Procedure Assistance and Support 6 I Eran PORE ooo rude Go acute pado 7 Weal Mamenn E cath me e i uM ade ena 7 137 EIC ODD Heo Hr EE 7 I1 Disposal ane RECY CHINO erare A E A S 7 2 INSTALLA ION 8 21 osos tute tats e 8 2 25 Site Consider das rca

Download Pdf Manuals

image

Related Search

Related Contents

poudre d`acide borique pressurisée  Phonix IP6PBCW mobile phone case  T5 Manual EU.book  HP Color Laserjet CP3525 Service Manual pages - service  ROUTER-B CARD FOR AM3440 USER`S MANUAL  Samsung MWR-WE10 manual de utilizador  adrenalina vet  Instruments - Freightliner Trucks  manuale utente modello 7420-7820  PDF形式(11.4 KB)  

Copyright © All rights reserved.
Failed to retrieve file