Product User Manual
Contents
1. THE INSTALLER IMPORTANT All operations requiring the opening of the casing such as installation programming and repair etc must be carried out by skilled staff only The fixing of power supply leads and connection cables must be secured through the use of cable clamps Rev 1 2 03 07 STATEUROP hereby declares that the product below MR4 Single channel Receiver complies with the require ments of Directive R amp TTE 99 5 EC 1 Rev 1 2 03 072. conditions of the area The receiver is fitted with an antenna consisting of a rigid wire section Should you wish to increase the device sensitivity you can connect a tuned antenna using a RG58 50 OHM coaxial cable The antenna should be placed on the exterior in a visible position away from any metallic structures The installation of two receivers placed less than 5 metres from one an other is not possible OPERATION WITH RADIO CONTROLS AND OR TRANSPONDERS The receiver can be combined with MOTORLINE radio controls and or transponders and is designed to store up to 500 different users We therefore recommend you make a note of the memory position user name correspondence in the form provided For use with radio con trols the receiver is fitted with an incorporated receiver PROGRAMMING RADIO CONTROLS AND OR TRANSPONDERS The programming of radio controls and or transponders is self learning as follows Use the UP or DOWN keys to go to the desired memory position viewed on the display from 001 to 500 paying attention to the TRANSMITTER and TRANSPONDER LEDS as one of them turning on means the location is busy Press the SEL key the TRANSMITTER and TRANSPONDER LEDS will begin to flash and meanwhile send the code with the radio control or bring the transponder closer to the ML3 proximity reader the display will indicate STO stored the TRANSMITTER or TRANSPONDER LED will go from off to on and pro gramming is
3. thus complete To delete a radio control or transponder stored previously use the UP or DOWN keys to go to the memory location that is busy press the SEL key the TRANSMITTER or TRANSPONDER LED will begin to flash press the SET key the display will indicate DEL deleted the LED will go from on to off and delete is thus complete During normal operation the display panel indicates the memory loca tion of the device stored previously currently in use Rapip PROGRAMMING OF RADIO CONTROLS AND OR TRANSPONDERS The rapid programming of radio controls and or transponders is only al lowed when all the receiver memory is free To make sure that all the memory is free follow the Reset procedure Rapid programming means you do not have to select a new memory location for another radio control and or transponder every time but starting from position 001 the control unit automatically increases the memory location and remains on standby for 10 seconds from the in put of a new radio control and or transponder to store ASSWORD Once you have finished programming the radio controls and or transponders you can store a password in the PAS position to disable and enable receiver programming as follows Use the UP or DOWN keys to go to the PAS memory position press the SEL key the TRANSMITTER and TRANSPONDER LEDS will be gin to flash and meanwhile use the UP or DOWN key to select a num ber between 001 and 500 press the SET key the dis
4. MR4 SINGLE CHANNEL RECEIVER The MR4 radio receiver is designed for the remote operation of electric al and electronic equipment in conjunction with one or more MOTOR LINE radio controls and or transponders MB1 MB2 Mod MR4 433 92 MHz TECHNICAL DATA Power supply 12 24VAC DC Max consumption 4 5 W Op radio controls Op transponders 12 18 Bit or Rolling Code Card or Key ring Stored codes 500 Max 1 one command relay 30VDC 1A Working temperature 10 C 55 C 110x121x47 mm ABS UL94V 0 IP54 30 70 metres Dimensions Container Protection degree Radio control range in open spaces e le SEL SET UP gO pown TRANSMITTER TRANSPONDER CONNECTION OF TERMINAL BOARDS CN1 24 VAC DC power supply input 0 V power supply input 12 VAC DC power supply input Clean command contact output Clean command contact output Earth input Antenna hot pole input NOOR WOM CN2 Connection for Transponder 1 Reader ML3 CN3 Connection for Transponder 2 Reader ML3 CN4 Connection for PC SW 2189 interface CN5 Normally open or closed command contact selection RECEIVER INSTALLATION For the optimal operation between transmitter and receiver we recom mend you choose the point of installation carefully The range is not merely linked to the technical features of the device itself but it actually varies according to the radioelectric
5. play will indicate CLO closed and the TRANSMITTER and TRANSPONDER LEDS will go from off to on To re enable programming use the UP or DOWN keys to go to the PAS memory position press the SEL key the TRANSMITTER and TRANSPONDER LEDS will begin to flash meanwhile use the UP or DOWN keys to select the key number selected previously press the SET key the display will indicate OPE open To delete a password operation only allowed if the system is open OPE use the UP or DOWN keys to go to the PAS memory position press the SEL key the TRANSMITTER and TRANSPONDER LEDS will begin to flash and meanwhile press the SET key the display will in dicate DEL deleted the TRANSMITTER and TRANSPONDER LEDS will go from on to off N B if you enter an incorrect password you will have to wait 5 minutes to repeat the operation and if you enter another incorrect password you will have to wait 1 hour ESET If it is appropriate for the factory configuration to be restored operation only allowed if the system is open OPE press the SEL and SET keys simultaneously and the LEDS will turn off and the display will indicate the PAS position N B the display is turned off after one minute of inactivity to save en ergy FURTHER Functions Via PC ConneEcTION The receiver can be connected to a Personal Computer through the use of a SW 2189 package supplied as an optional thanks to which you may access further functions FOR
Download Pdf Manuals
Related Search