USER MANUAL - Flash
Contents
1. USER MANUAL LED BEAM MOVING HEAD 108 Professional Entertainment Technology www flash butrym pl Strona 1 TABLE OF CONTENTS Safety Instruction 2 Technical Specification 3 How To Set The Unit 4 How To Control The Unit 5 Troubleshooting 6 Fixture Cleaning Please read carefully the instruction which includes important infor mation about the installation usage and maintenance WARNING Please keep this User Guide for future consultation If you sell the unit to another us er be sure that they also receive this instruction booklet Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit Its important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Disconnect main power before replacement or servicing Make sure there is no flammable materials close to the unit while operating as it is fire hazard Use safety cable when fixes this unit Don t handle the unit by taking its head only But always by taking its base Maximum ambient temperature is ta 40 C Don t operate it where the temperature is higher than this www flas2. ar electrical appliances Part 1 General requirements www flash butrym pl Strona 9
3. c strobe with variable speed 0 20hz or the result of random PAN 6300 TILT 2400 Speed control PAN TILT DMX CONTROL AND PROGRAMMING Control of the market definition PAN and TILT 8bit or 16bit DMX512 9 12 or 16 channels Sound control master slave Setting and addressing LCD with back light OPTICS Viewing angle 5 Light power LUX 66 000 2m 16 500 4 5 m CREE 3W LED s 28xR 28xG 26xB 26xW EXECUTION Aluminum construction with plastic www flash butrym pl Strona 4 Two side handles for transportation Degree of protection IP20 INSTALLATION Two handles for screw hooks Indoor use only Mounting head in any position Minimum distance to illuminated surfaces 1 mouth Keep a minimum distance from the surrounding area of the head 0 5 m CONNECTORS Power connector IN Neuritic Power Con Power connector OUT Neuritic Power Con DMX512 signal connector 3 pin XLR IN OUT ELECTRICAL Power supply AC 110V 240V 50 60Hz Maximum power consumption 320W Protection T6 3A ACCESSORIES INCLUDED IN Power Con power cable blue connector Brackets for attaching the head to the structure 1pc Filter Wash 25 User manual USEFUL INFORMATION FOR ORDERING Packaging 1unit 410x390x285mm Gross Weight 9 8 kg 3 How To Set The Unit 3 1 Control Panel Display www flash butrym pl Strona 5 To show the various menus and the selected functions Led DMX On DMX
4. d to set DMX address from 1 to 512 so that the units can receive DMX signal Press the MENU button up to when the DMX Address is showing on the display Pressing ENTER www flash butrym pl Strona 7 button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode Please refer to the following diagram to address your DMX512 channel for the first 4 units Channel mode Unit 1 Unit 2 Unit 3 Address Address Address Unit 4 Address 9 channels h 10 19 08 12 channels N 13 25 37 16 channels fit 17 33 49 4 4 DMX 512 Configuration 9 Channel Mode Channel List Value Function CH1 000 255 Pan 0 630 CH2 000 255 Tilt 0 240 CH3 000 255 Strobe CH4 000 255 Red 0 100 CH5 000 255 Green 0 100 CH6 000 255 Blue 0 100 CH7 000 255 White 0 100 CH8 000 255 Dimmer 0 100 CH9 240 255 Reset 240 255 Sound 12 Channel Mode Channel List Value Function CH1 000 255 Strobe Effect CH2 000 255 Dimmer 0 100 CH3 000 255 Pan 0 630 CH4 000 255 Pan Fine Least significant bit CH5 000 255 Tilt 0 240 CH6 000 255 Tilt Fine Least s
5. h butrym pl Strona 2 Unit surface temperature may reach up to 85 C Dont touch the housing bare hand during its operation Turn off the power and allow about 15 minutes for the unit to cool down before replacing or serving In the event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type Spare parts Warning To prevent or reduce the risk of electrical shock or fire do not expose the unit the rain or moisture Do not open the unit within five minutes after switching off The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service Please contact your nearest dealer Installation The unit should be mounted via its screw holes on the bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping white operating And make sure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit s weight Also always use a safety cable hold 12 times of the weight of the unit when installing the fixture The equipment must be fixed by professional
6. ignificant bit CH7 000 249 Reset 250 255 Sound Activat CH8 000 255 Ko CH9 000 255 Red 0 100 CH10 000 255 Green 0 100 CH11 000 255 Blue 0 100 CH12 000 255 White 0 100 16 Channel Mode Channel List Value Function CH1 000 255 Pan 0 630 CH2 000 255 Pan Fine Least significant bit CH3 000 255 Tilt 0 240 CH4 000 255 Tilt Fine Least significant bit CH5 000 255 Pan amp Tilt Speed CH6 000 255 Pan amp Tilt Auto Run CH7 000 255 Auto Run Speed CH8 000 240 Reset 240 255 Aoto run color CH9 000 255 Dimmer 0 100 7 www flash butrym pl Strona 8 CH10 000 255 Strobe CH 11 000 255 Red 0 100 CH12 000 255 Green 0 100 CH13 000 255 Blue 0 100 CH14 000 255 White 0 100 CH15 000 255 Color Auto Run CH16 000 255 Color Auto Run Speed Reset Press the MENU button up to when the Reset is blinking on the display Pressing ENTER button and all channels of the unit will return to their standard position EC Declaration of Conformity We declare that our products lighting equipment comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55014 2 1997A1 2001 EN61000 4 2 1995 EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 amp Harmonized Standard EN60598 1 2000 ALL 2000 A12 2002 Safety of household and simil
7. input Present MASTER On Master Mode Slave On Slave Mode Sound Flashing Sound activation Button MENU To select the programming functions DOWN To go backward in the selected functions UP To go forward in the selected functions ENTER To confirm the selected functions DMX Address 001 512 9CH Channel Set Show Mode 12CH 16CH SHOW1 SHOW2 Slave Set SHOW3 SHOW4 SLAVE1 Black Out SLAVE2 YES Sound Mode NO ON Sound Sense OFF MENU Pan Inverse 100 YES Tilt Inverse NO YES www flash butrym pl Strona 6 NO White Balance RED 125 GREEN BLUE 255 PAN TILT RED 0 BLUE 255 DIMMER Temp 31 C NO Pro Defaults Defaults YES Auto Defaults Fixture Reset NO YES COMMON DMX DMX INPUT 3 DMX OUTPUT Termination reduces signal errors and avoids signal tranmission problems and interference It is always E Y advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX jand pin3 DMX of the last fixture DMX Controller By using a universal DMX Controller to control the units you will nee
8. s And it must be fixed at a place where is out of the touch of people and has no one pass by or under it Fixture Cleaning The cleaning of internal and external optical lens and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the units optics Clean with soft cloth using normal glass cleaning fluid Always dry the parts carefully Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days www flash butrym pl Strona 3 Another new edition of Led Moving Head 108 x 3W RGBW well know has Strong but this time it came with CREE LED s and it very attractive light And it have 108 high quality LED Red Green Blue White that make it to provides a very good light and bright in which make it have a strong and very concentrated light beam The view Angle 5 and You also get a complete additional filter that will turn wider the wash angle to 25 FEATURES High quality CREE LED s in four basic colors RGBW Angle 5 25 additional filter color Balance Extremely fast and very good precise movement Ultra compact design light The device weight 8 4 kg PHYSICAL Height 390 mm Width 370 mm Depth 265 mm Weight 8 4 kg DYNAMIC EFFECTS RGBW color mixing Liquid electronic dimmer 0 100 Electroni
Download Pdf Manuals
Related Search