WW Tone User Manual - Elation Professional
Contents
1. C 1 1 cp i FI FANS F OR GFF IAUEO HISH LO LO GFF HOLe AUEO to XM605 V1 0 NR FAIL lt FAIL gt DMX Fault Protection This function dictates how the fixture will operate in the event DMX signal is suddenly lost while operating in DMX mode The three fail safe modes are 1 OFF which will blackout all light output 2 HOLD which will hold the last DMX command or 3 AUTO which will put the fixture in sound active mode d SE lt DFSE gt Restore Default This function is used to restore the factory settings of the device All settings will be set back to the default values shaded Any edited scenes will be lost mL PUR Power on to preserve the MANL settings This function will preserve all the manual setting that are made in the MANL menu section If this function is not activated all manual settings will be lost once the fixture is tuned off Z ori FAS This function is used to change the functionality of the internal cooling fans Follow the procedure below to access the fan menu 1 Access the main menu Tap the UP or DOWN button until SPEC is displayed press ENTER Tap the UP or DOWN button until FANS is displayed press ENTER The display will show HIGH AUTO LOW Press UP or DOWN button to select HIGH AUTO2. or LOW Press ENTER to confirm Press MODE ESC to return to the main menu oe ee ow ee ae Te i lt VER gt Software Version This function will display the current firmware version HAIL MANL Manual Fixture Settings This function allows the each of the ten DMX channels to be controlled manually This will allow the fixture to be preset to a specific color or built in program without the use of a DMX console 1 Select MANL by pressing UP or DOWN button 2 Press ENTER the display shows WHIT STRB 1 0 XM605 V1 0 NR 3 Press UP or DOWN button to select WHIT STRB 4 Press ENTER to confirm or Press MODE ESC to return to the main menu J IIE TIME Operating Hours These functions will detail different time functions associated with the fixture EE UEE BOO0 9999 FigE IE038 CLFEJ ONZOFF LIFE lt LIFE gt 0000 9999 Hours This function tracks the running time of the fixture from the point it was last Where XXXX represents the total number of running hours This time is destructive and will remain in the fixtures memory indefinitely Use this time cleared none to track rentals or show durations CC dle lt CODE gt Clear run time access code This lock out code prevents the current run time from being erased accidently
3. salve DMX chain In Alone mode UAL This function will electronically display the current DMX value for any channel currently being adjusted The display will automatically detail the values as they are received from the controller This VALU Display the DMX 512 value of each channel that is changing DMX function is off by default ZI ID Fil FLIP This function will flip the display readout by 180 allowing for better visualization when the fixture is mounted in an inverted position d on avoid excessive light in situations that require an extremely dark environment This function will adjust the time delay the fixture will remain on before it turns off D ON The display is designed to turn off during normal operation to This function is disabled as default MTL LOLI LOCK This function allows you to lock the keys This function activates the automatic key lock command If this function is activated all menu keys will automatically lock whit in 15 seconds of the last temporarily deactivate the key lock function press and hold menu function To down the Mode Esc button for 3 seconds Lim EE SET Fixture Personality Settings These functions set specific running modes and operating parameters m oa X hin Fer oc rr
4. the device Avoid brute force when installing or operating the device While choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust Please don t project the beam onto combustible substances The minimum distance between light output from the projector and the illuminated surface must be more than 0 1 meter If you use the quick lock cam in hanging up the fixture please make sure the quick lock fasteners turned in the quick lock holes correctly Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation 2 c XM605 V1 0 NR Please use the original packaging if the device is to be transported For safety reasons please be aware that all modifications on the device are forbidden If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to short circuit burns electric shock lamp explosion crash etc INSTALLATION INSTRUCTIONS a Mounting the device CAUTION Please consider the GB7000 15 EN60598 2 17 and the other respective national norms during the installation The installation must only be carried out by a qualified person The applicable temperature for the lighting is between 25 C to
5. 45 C Do not use the lighting under or above the temperature The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate safety rope Never stand directly below the device when mounting removing or servicing the fixture The operator has to make sure the safety relating and machine technical installations are approved by an expert before taking the device into operation for the first time These installations have to be approved by a skilled person once a year Overhead mounting requires extensive experience including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury CAUTION The electric connection must only be carried out by a qualified electrician Before mounting make sure that the installation area can hold a minimum point load of 10 times the device s weight Connect the fixture to the mains with the power plug a aa XM605 V1 0 NR Installation via the Omega holders a Fixed the clamp on the bracket by tighten up the M12 screw on the bracket to the 13 hole in the middle of the bracket b Inse
6. ETATION PROFESSIONAL WW TONE Thank you for your patronage We are confident that our excellent products and service can satisfy you For your own safety please read this user manual carefully before installing the device In order to install operate and maintain the lighting safety and correctly We suggest that the installation and operation should be done by the verified technician and follow the instruction strictly CAUTION Keep this device away from rain and moisture CAUTION Unplug mains lead before opening the housing Every person involved with the installation operation and maintenance of this device has to be qualified follow carefully the instructions of this manual INTRODUCTION Thank you for having chosen this professional LED moving head You will see you have acquired a powerful and versatile device Unpack the device Inside the box you should find 1 One XLR connection cable 2 A power cable 3 One safety rope 4 Manual 5 Barn door 6 Frost filter Please check carefully that there is no damage caused by transportation Should there be any consult your dealer and don t install this device Features e LED type BXRA W3000 e Channel mode 2 channels Strobe effect with 1 13 flashes per second and pulse effect 4 digit LED display e Display Can be changed 180 reverse to fit for different installation position e Software upload by optional accessory via DMX line
7. Overview 1 Display 2 Mode Esc button 3 Up button 4 Down button 5 Enter button 6 Safety eyelet 7 Power output 8 Power inpot Fuse 9 3 Pin DMX in 10 3 Pin DMX out 11 Fixation screw 12 Floor stand SAFETY INSTRUCTIONS CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class I Therefore it is essential that the device be earthed The electric connection must carry out by qualified person Make sure that the available voltage is not higher than stated at the end of this manual 1 XM605 V1 0 NR Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by a
8. The access code is 038 CLEE lt CLFE gt clear Fixture Run Time This function resets the run time to zero Te c di Edit Internal Program Settings The fixture comes equipped with a built in DMX recorder that allows custom programs to be installed and recalled directly from the fixture s control board Programs can be created and stored using the fixture s control board or by using an external DMX controller For detailed instructions on how to complete this task please see Working with Built In Programs Section 11 Page 27 Select program This function allows the user to select one of ten of the user defined built in programs This program is then accessed in Function Mode under Program Run REC Auto save function Edit program This function allows the user to edit the built in programs XM605 V1 0 NR Edit Scenes This function allows the user to edit or define the actual scenes that previous are stored in the user defined built in programs that are accessed in the step CEDT Edit program using a external controller Editing procedure 1 Using the control board only ls 2 9 Access the main menu Tap the UP button until EDIT is displayed and press ENTER The display will show SC 01 this stands for the scene number For example SC 01 is displayed it means you will be editing scene 1 press ENTER You can cha
9. d condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakness of the lights due to accumulation of dust 2 Clean the fan each week 3 A detailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device except for the lamp Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer TECHNICAL SPECIFICATIONS Power supply AC 100V 240V 50Hz 60Hz Remark errors and omissions for every information given in this manual excepted All information is subject to change without prior notice 15 XM605 V1 0 NR
10. effect slow to fast 224 255 Led turn on 1 Instructions for installing the barn door and frost filter For this device the barn door and the frost filter can be installed separately or together 1 When only install the frost filter use the rotating clips on the lens cover to fix it 2 When only install the barn door loose the 4 M4 screws on the lens cover put on the bar door and tighten the screws 3 When install the barn door and frost filter together loose the 4 M4 screws put on the frost filter and the bar n door one by one then tighten the screws Loose 4 screws 14 XM605 V1 0 NR CLEANING AND MAINTENANCE The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed CAUTION Disconnect from mains before starting maintenance operation In order to make the lights in goo
11. erminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1209 2 3 1 PIN3 PIN 2 Projector DMX start address selection All fixtures should be given a DMX starting address when using a DMX signal so that the correct fixture responds to the correct control signals This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out from the DMX controller The allocation of this starting address is achieved by setting the correct number on the display located on the base of the device You can set the same starting address for all fixtures or a group of fixtures or make different address for each fixture individually If you set the same address all the units will start to listen to the same control signal from the same channel number In other words changing the settings of one channel will affect all the fixtures simultaneously If you set a different address each unit will start to listen to the channel number you have set based on the quantity of control channels of the unit That means changing the settings of one channel will affect only the selected fixture In the case of the move head which is a 2 channel fixture you should set the starting address of the first unit to 1 the second unit to 3 2 1 the th
12. ird to 5 2 3 and so on 50 XM605 V1 0 NR Note The modes of DMX 512 data are shown via the display orci HLL A OLI DMX OK NO DMX 1 After switching on the device will automatically detect whether DMX 512 data is received or not If the data is received the display will show A 001 with the actually set address If there is no data received at the DMX input the display will flash A001 with the actually set address This situation can occur if the 3 PIN XLR plug cable with DMX signal from controller is not connected with the input of the device the controller is switched off or defective if the cable or connector is defective or the signal wires are swap in the input connector It s necessary to insert the XLR termination plug with 120 Ohm in the last lighting in the link in order to ensure proper transmission on the DMX data link Control Board There are four keys on the control panel which could be used to set the address turn ON OFF operating the program and reset Mode Esc press this key to enter into edit mode Press this key under the edit mode if you want to return to previous menu it will exit from edit mode 60 seconds after the last keypress UP screen will flash when pressing this key in normal mode the adress value will increasing Keep pressing this key the address value will increase rapidly it will exit from flash 60 seconds after the last keypres
13. lly detail the changing DMX values as they are received from the controller Ci or SLAV Slave setting for Master Slave Operation With this function you can define the device as slave for operation in Master Slave mode Each slave setting will have a different function for a dynamic lightshow without a controller RDMX Address via DMX This function allows the DMX address to remotely be adjusted from a DMX console This setting requires special settings for both the controller and the fixture RDMX is on by default For operational instructions please see Section 9 Page 23 of this manual Remote DMX addressing cu lt RUN gt Internal Program Settings This function allows the internal programs to run in either stand alone or master salve mode In Master mode the fixture will send DMX data to other fixtures connect via the DMX chain In Alone mode the fixture will operate as a single fixture The program for this mode is selected in the Select program section of the control eo oF XM605 V1 0 NR menu You can set the number of steps under Edit program You can edit the individual scenes under Edit scenes With this function you can run the individual scenes either automatically i e with the adjusted Step Time IIC d ISP lt DISP gt Menu Display Settings This function allows the internal programs to run in either stand alone or master
14. lt CLFE gt ON OFF Clear machina running time lt STEP gt S 01 S 48 Select steps of program REC RE XX Auto Save Scene WHIT WXXX STRB SXXX EDIT lt SC01 gt FADE XXX Edit the internal scenes lt SC48 gt XX X 000 1S 999 9 TIME S CEDT ON OFF Edit program via controller Default settings shaded XM605 V1 0 NR Main Menu Functions HUE MODE Function Mode lt ADDR gt DMX address setting This function is used to set or adjust the fixture s starting DMX address Every device controlled by DMX has to have a unique starting address The addressing feature is what allows DMX to function properly The DMX address of a fixture is what allows it to communicate with a controller properly The DMX addressing also allows the fixture to ignore any DMX information coming from the controller that is not meant specifically for the fixture Because each fixture is connected in a daisy chain fashion it is imperative to assign a proper and unique starting DMX address to each and every fixture The DMX address is non destructive and will remain in the fixture s memory even when the power to the unit is switched off Memory is backed up and retain by an internal power source that should last about five years l ILII OAL VALU Display the DMX 512 value of each channel With this function you can display the DMX 512 value of each channel The display will automatica
15. n authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard CAUTION Never touch the device during operation The housing may heat up CAUTION Never look directly into the light source as sensitive persons may suffer an epileptic shock Please be aware that damages caused by manual modifications to the device are not subject to warranty Keep away from children and non professionals GENERAL GUIDELINES This device is a lighting effect for professional use on stages in discotheques theatres etc the device was designed for indoor use only This fixture is only allowed to be operated with the max alternating current which stated in the technical specifications in the last page of this manual Lighting effects are not designed for permanent operation Consistent operation breaks may ensure that the device will serve you for a long time without defects Do not shake
16. nge the scene number by tapping the UP button Press ENTER the display will show C 01 this represents the channel number If C 01 is displayed you will be editing the fixture s channel 1 value of the selected scene press ENTER You can change the channel number by tapping the UP button The display will show the DMX value for the channel that is being edited It will be displayed as 11XX it stands for Channel 11 of the editing scene the DMX value is XX Adjust the DMX value by tapping the UP button until you get the expected effect for this channel 7 Press ENTER to enter the editing of the other channels of the scene 8 Repeat steps 5 8 until you finish setting all the DMX values for all the channels of this scene each scene can have 16 channels maximum Once all the channels are completed the display will begin to flash TIME this indicates the time needed to run this scene 10 Press ENTER to edit the time needed the display shows TXXX XXX represents the time needed to run this scene For example T002 means scene 1 needs 0 4 seconds to run T 15 means this scene needs 3 0 seconds to run Note XX is always 0 2 seconds not one second 11 Adjust the time needed by tapping the UP button 12 Press ENTER to save the settings for the scene you are editing the display will change to the next scene automatically 13 Repeat steps 3 12 to edit other scene
17. rt the quick lock fasteners of the first Omega holder into the respective holes on the bottom of the device Tighten the quick lock fasteners fully clockwise c Install the second Omega holder d Pull the safety rope through the holes on the bottom of the base and over the trussing system or a Safe fixation spot Insert the end in the carabine and tighten the safety screw Notice this step is quite important to ensure that the fixture will not drop out by the damage of the clamp DMX 512 control connection Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below 4 XM605 V1 0 NR Address 1 Address 3 Address5 DMX output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket 1 Ground 2 Signal 3 Signal DMX controller X 120 Ohms j DMX512 gt DMX 512 connection with DMX terminator For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX t
18. s Press this key under edit mode you can choose the function you want from the buttom up in the menu DOWN screen will flash when pressing this key in normal mode the adress value will idecreasing Keep pressing this key the address value will decrease rapidly it will exit from flash 60 seconds after the last keypress Press this key under edit mode you can choose the function you want from the top down in the menu ENTER this key is functionless when in normal mode Press this key under the edit mode it will enter into next menu 6 XM605 V1 0 NR A001 A XXX VALU AXXX IDMX address setting lt ADDR gt SLAV ON OFF Set as Slave RDMX ON OFF Change address via DMX lt RUN gt IAUTO IALON MAST Run Auto program MODE VALU D XX D 00 DXXX Display DMX value FLIP ON OFF Flip display D ON ON OFF Delay shutting off LED display lt DISP gt Key lock Press the MENU button for 3 LOCK ON OFF seconds to activate lt FAIL gt OFF HOLD AUTO Status while there is no DMX lt DFSE gt ON OFF Default setting Power on to preserve the MANL SET lt POHO gt ON OFF settings lt FANS gt IAUTO HIGH LOW IFan s mode select lt VER gt V 1 0 V 9 9 Software version Manual adjust intensity Manual adjust lt WHIT MANL WXXX intensity STRB gt SXXX lt LIFE gt 0000 9999 HOURS Life time of machina running TIME KCODE gt CXXX IPassord of clear time 038
19. s you can edit and save 48 scenes 1 2 XM605 V1 0 NR maximum 14 Press MODE ESC to exit and save your edited scene into the fixtures internal memory The number of steps can be defined under EDIT and the scenes can be called up under Run To run the scenes see page 30 Editing procedure 2 Using an external controller 1 2 4 7 8 10 Ti 12 Call up the first scene in your controller now Select SC01 by pressing the UP or DOWN buttons Press MODE ESC the display shows SC01 Press MODE ESC the display shows C 01 ect CEDT by pressing the UP or DOWN buttons Press MODE ESC the display shows OFF Press UP the display will read ON Press MODE ESC the display shows SC02 You successfully Sel downloaded the first scene Adjust the Step time as described above Call up the second scene in your controller now Repeat steps 5 11 until all desired scenes are downloaded Press MODE ESC to exit The number of steps can be defined under STEP and the scenes can be called up under RUN 13 XM605 V1 0 NR INSTRUCTIONS ON USE DMX channel s functions and their values Channel Value Function 2CH White LED 0 255 White 0 Black 255 100 White Shutter strobe 0 31 Led trun off 32 63 Led turn on 64 95 Strobe effect slow to fast 2 96 127 Led turn on 128 159 Pulse effect in sequences 160 191 Led turn on 192 223 Random strobe
Download Pdf Manuals
Related Search