DX 33HML manual
Contents
1. a location that is convenient for operation and does not interfere with the driver or passengers in the vehicles In automobiles the transceiver is usually mounted below the dash panel with the microphone bracket beside it MOUNTING THE CONNECTION Your transceiver is supplied with a universal mounting bracket When mounting the bracket and radio to your car make sure it is mechanically strong Also provide a good electrical connection to the chassis of the vehicle Proceed as follows to mount the transceiver 1 After you have determined the most convenient location in your vehicle hold the transceiver with mounting bracket in the exact location desired If nothing will interfere with mounting it in the desired position remove the mounting bolts Before drilling the holes make sure nothing will interfere with the installation of the mounting bolts 2 Connect the antenna cable plug to the standard receptacle on the rear panel Most antennas are terminated with a type PL 259 plug and mate with the receptacle 3 Connect the red DC power input wire with the fuse to 13 8V DC This wire extends from the rear panel In automatic installation 13 8V DC is usually obtained from the accessory contact on the ignition switch This prevents the set being left on accidentally when the driver leaves the car and also permits operating the unit without the engine running Locate the accessory contact on most ignition switches by tracing the power wir2. completion of the microphone plug wiring connect and secure the microphone plug in the transceiver 14 nw gt Fig 2 Microphone plug wiring Remove the retaining screw Unscrew the housing from the pin receptacle body Loosen the two cable clamp retainer screws Feed the microphone cable through the housing knurled ring and washer as shown Fig 2 The wires must now be soldered to the pins as indicated in the above wiring tables If a vise or clamping tool is available it should be used to hold the pin receptacle body during the soldering operation so that both hands are free to perform the soldering If a vise or clamping tool is not available the pin receptacle body can be held in a stationary position by inserting it into the microphone jack of the front panel The numbers of the pins of the microphone plug are shown in Fig 3 as viewed from the back of the plug Before soldering the wire to the pins pre tin the wire receptacle of each pin of the plug 13 Specifications GENERAL Frequency Range Frequency Control Frequency Tolerance Frequency Stability Operating Temperature Range Microphone Input Voltage Size Weight Antenna Connector Meter TRANSMITTER Power output Modulation Spurious Emissions Frequency Response Output Impedance Output Indicators 28 065 to 28 505 MHz Phase Lock Loop PLL synthesizer 0 005 0 001 30 C to 50 C Plug in dynamic with push to talk swit
3. hold the microphone two inches from the mouth and speak clearly in a normal voice The radios come complete with low impedance 500 ohm dynamic microphone For installation instruction on other microphones see next section ALTERNATE MICROPHONES AND INSTALLATION OPERATING PROCEDURE TO RECEIVE 1 Be sure that power source microphone and antenna are connected to the proper connectors before going to the next step Turn unit on by tuning VOL control clockwise on your transceiver Set the VOLUME for a comfortable listening level Set the MODE switch to the desire mode Listen to the background noise from the speaker Turn the SQUELCH control slowly clockwise until the noise JUST disappears no signal should be present Leave the control at this setting The SQUELCH is now properly adjusted The receive will remain quiet until a signal is actually received Do not advance the control too far or some of the weaker signals will not be heard Set CHANNEL selector switch to the desired channel Set the RF gain control fully clockwise for maximum RF gain Aw Rw oN OPERATING PROCEDURE TO TRANSMIT Select the desired channel of transmission 2 Set the MIC GAIN control fully clockwise 3 Ifthe channel is clear depress the push to talk switch on the microphone and speak in a normal voice ll Installation LOCATION Plan the location of the transceiver and microphone bracket before starting the installation Select
4. ES AND INSTALLATION For best results the user should select a low impedance dynamic type microphone or a transistorized microphone Transistorized type microphones have a low output impedance characteristic The microphones must be provided with a four lead cable The audio conductor and its shielded lead comprise two of the leads The fourth lead is for receive control and the third is for transmit control The microphone should provide the functions shown in schematic below 4 WIRE MIC CABLE Pin Number Mic Cable Lead 1 Audio shield 2 Audio Lead 3 Transmit control 4 Receive Control Fig 1 Your transceiver microphone schematic If the microphone to be used is provided with pre cut leads they must be revised as follows 1 Cut leads so that they extend 7 16 beyond the plastic insulating jacket of the microphone cable 2 All leads should be cut to the same length Strip the ends of each wire 1 8 and tin the exposed wire Before beginning the actual wiring read carefully the circuit and wiring information provided with the microphone you select Use the minimum head required in soldering the connections Keep the exposed wire lengths to a minimum to avoid shorting when the microphone plug is reassembled 12 PRESS TO TALK MICROPHONE The receiver and transmitter are controlled by the press to talk switch on the microphone Press the switch and the transmitter is activated release switch to receive When transmitting
5. WARRANTY This radio is covered by a two year limited parts and labor warranty Limited means that we will repair problems caused by factory defects or normal use at no charge Before returning a radio to us for warranty service please call our Service Department for a Repair Authorization Number RAN This RAN must be written below your return address on the outside of the shipping box Boxes which arrive without a RAN will be refused and the shipping company will return the unopened box to you Be sure to have a pen and paper ready along with the serial number of your radio before calling We will give you the RAN and our shipping address over the phone The telephone number of the Service Department is 760 480 8800 and we suggest calling between 10 00 AM and 4 00 PM Pacific Time Please include a note with a detailed description of the symptoms This is important because it will help the technician who works on your radio to locate your problem Intermittent problems are easily overlooked so be sure to give as much detail as possible in your note Also please include your telephone number in case our technicians have any additional questions Do not send your power cord or microphone unless we ask for these items during our telephone conversation You are responsible for getting the radio safely to us We suggest using United Parcel Service You must pay to ship the radio to us and we will pay to ship the radio back
6. ch and coiled cord 13 8V DC nominal 15 9V max 11 7V min Positive or negative ground Transmit AM full mod 2 2A Receiver Squelched 0 3A Maximum Audio output 0 7A 2 3 8 H x 7 7 8 W x 9 1 4 D 5 Ibs UHF S0239 Illuminated indicates relative output power received signal strength AM FM High 7 watts Low 3 5 watts High and low level Class B Amplitude Modulation AM Variable capacitance Frequency Modulation FM 60 dB AM and FM 450 to 2500 Hz 50 ohms unbalanced Meter shows relative RF output power and SWR Transmit LED glows red when transmitter is in operation RECEIVER Sensitivity Selectivity Image Rejection IF Frequency Adjacent Channel Rejection RF Gain Control Automatic Gain Control AGC Squelch ANL Noise Blanker Audio Output Power Frequency Response Built in Speaker External Speaker Not Supplied AM 0 5 uV for 10 dB S N N at greater than Y watt of audio output FM 1 0 uV for 20 dB S N N at greater than watt of audio output AM FM 6 dB 3 KHz 50 dB 9 KHz More than 65 dB AM FM 10 695 MHz 1 IF 455 KHz 2 IF 60 dB AM 45 dB adjustable for optimum signal reception Less than 10 dB change in audio output for inputs from 10 to 100 000 microvolts Adjustable threshold less than 0 5 uV Switchable RF type 4 watts into 8 ohms 300 to 2800 Hz 8 ohms round 8 ohms disables internal speaker when connected ATERNATE MICROPHON
7. e from the AM broadcast receiver in the car 4 Connect the black lead to 13 8V DC This is usually the chassis of the car Any convenient location with good electrical contact remove paint may be used 5 Mount the microphone bracket on the right side of the transceiver or near the transceiver using two screws supplied When mounting in an automobile place the bracket under the dash so the microphone is readily accessible IGNITION NOISE INTERFERENCE Use of a mobile receiver at low signal levels is normally limited by the presence of electrical noise The primary source of noise in automobile installations is from the generator and ignition system in the vehicle Under most operating conditions when signal level is adequate the background noise does not present a serious problem Also when extremely low level signals are being received the transceiver may be operated with vehicle engine turned off The unit requires very little current and therefore will not significantly discharge the vehicle battery Even though the transceiver has ANL and NB controls in same installations ignition interference may be high enough to make good communications impossible The electrical noise may come from several sources Many possibilities exist and variations between vehicles require different solutions to reduce the noise ANTENNA A vertically polarized quarter wavelength whip antenna provides the most reliable operation and greatest range S
8. ed to this jack the built in speaker is automatically disconnected PA SP Used to connect a PA speaker 8 ohm 4W for PA operation Before operating PA you must first connect a PA speaker to this jack ANTENNA Accepts 50 ohm coaxial cable with a type PL 259 plug to be connected F C This socket is optional for the accessories FREQUENCY COUNTER model FC 347 to indicate the value of the frequency ranges used 10 10 11 12 13 14 15 16 MODE PA FM AM SWITCH This switch is used to select PA FM AM mode of operation The AM or FM mode is normally but when you set to PA position the transceiver acts as a public address amplifier Before operating PA you must first connect an external PA speaker 8 ohm more than 2W to the PA Speaker jack on the unit rear panel BAND SELECTOR This switch selects A B C D E or F band of operation ECHO This control is used to echo effect TIME This control is used to intervals of echo sound CHANNEL SELECTOR This switch selects any one of the forty channels desired The selected channel appears on the LED readout directly above the Channel Selector knob METER This meter indicates received signal strength transmitter RF output power RF POWER This switch is used to select transmitting power In the HI position the transceiver operates in 7 watts RF output power In the MED position the transceiver operates 4 watts RF output power In the LO position t
9. he transceiver operates in 1 watts RF output power OFF ANL NB When the switch is placed in the ANL NB position the RF Noise Blanker also is activated The RF Noise Blanker is very effective for repetitive impulse noise such as ignition interference BAND SWITCH HI LOW This switch is used to select High band and or Low band Frequency Range OFF ECHO SWITCH This switch is used to add an echo effect to your transmitting voice when to ECHO position RECIEVER TRANSMIT INDICATOR The receiver transmit LED indicator is located next to the channel indicator When in receive the LED will be green When in transmit the LED will be red CHANNEL INDICATOR Numbered LED indicates the selected channel you wish to operate on LED indicates 9 when CH 9 is switched on TUNNING THE ANTENNA FOR OPTIMUM SWR Since there is such a wide variety of base and mobile antennas this section will strictly concern itself to the various types of mobile adjustable antennas Because the antenna length is directly related to the channel frequency it must be tuned to resonate optimally all 40 channels of the transceiver Channel 1 requires a longer antenna than Channel 40 because it is lower in frequency Due to the various methods of adjusting antennas for proper SWR we have chosen what we think is the optimum method A 1 Antennas with adjustment screws set screws Start with the antenna extended and tightens the set screw lightly enough s
10. horter loaded type whip antennas are more attractive compact and adequate for applications where the maximum possible distance is not required Also the loaded whips do not present the problems of height imposed by a full quarter wavelength whip Mobile whip antennas utilize the metal body of the vehicle as a ground plane When mounted at a corner of the vehicle they are slightly directional in the direction of the body of the vehicle For all practical purpose however the radiation pattern is nondirectional The slight directional characteristic will be observed only at extreme distance A standard antenna connector type SO239 is provided on the transceiver for easy connection to a standard PL 259 cable termination If the transceiver is not mounted on a metal surface it is necessary to run a separate ground wire from the unit to a good metal electrical ground in the vehicle When installed in a boat the transceiver will not operate at maximum efficiency without a ground plate unless the vessel has a steel hull Before installing the transceiver in a boat consult your dealer for information regarding an adequate grounding system and prevention of electrolysis between fittings in the hull and water REAR PANEL F 17 18 19 20 21 POWER Accepts 13 8V DC power cable with built in fuse 4 amp to be connected EXT SP Accepts 4 to 8 ohms 5 watt external speaker to be connected When external speaker is connect
11. le routing it may be pinched when routed into the car D Try a different location on your car keeping in mind the radiation pattern you wish Is the antenna perfectly vertical F Try a different location in your neighborhood Stay away from large metal objects when adjusting metal telephone or light posts fences etc NOTE The transceiver will operate into an SWR of 2 to 1 indefinitely and sustain an SWR of 20 1 for a maximum of 5 minutes at rated operating conditions EXTERNAL SPEAKER The external speaker jack EXT SPK on the rear panel is used for remote receiver monitoring The external speaker should have 8 ohms impedance and be able to handle at least 4 watts When the external speaker is plugged in the internal speaker is disconnected Operation CONTROL FUNCTIONS There are thirteen controls and three indicators on the front panel of your transceiver FRONT PANEL 1 OFF ON VOLUME inner dual concentric Turn clockwise to apply power to the unit and to set the desired listening level During normal operation the VOLUME control is used to adjust the output level obtained either at the transceiver speaker or the external speaker if used SQUELCH outer dual concentric This control is used to cut off or eliminate receiver background noise in the absence of an incoming signal For maximum receiver sensitivity it is desired that the control be adjusted only to the point where the receiver background noi
12. o that the antenna can be lightly tapped with your finger for easy adjustment Set your transceiver to Channel 21 Low band D or Hi band A Press the PTT push to talk switch and tap the antenna making it shorter The SWR meter will show a lower reading each time the antenna is tapped By continuing to shorten the antenna you will notice the SWR reading will reach a low print and then start riding again This means that you have passed the optimum point for Channel 21 Extend the antenna a short distance and again follow the procedure above When the lowest point has been reached switch to Channel 1 Low band A or Hi band A and then to Channel 40 Low band D or Hi band D and compare SWR readings They should be almost equal Antennas which must be cut to proper length Follow the same procedure as above but adjust the length by cutting in 1 8 increments until a good match is obtained Be very careful not to cut too much at one time as one it is cut it can no longer be lengthed The whip is easily cut by filing a notch all the way around and breaking the piece off with pliers NOTE THE PROPER SETTING IS ACHIEVED WHEN THE SWR IS 1 5 OR BELOW AND WHEN IT HAS THE SAME READING FOR CHANNELS LOW BAND A1 AND HI BAND D40 If you are having difficulties in adjusting your antenna check the following A All doors must be closed when adjusting the antenna B Make sure the antenna base is grounded C Check your coaxial cab
13. o solder If the washer is not captive to the pin receptacle body make sure that it is placed on the threaded portion of the pin receptacle body before soldering If the microphone jack is used to hold the pin receptacle during the soldering operation best results are obtained when the connections to pins 1 and 3 are made first and then the connections to pins 2 and 4 Use a minimum amount of solder and be careful to prevent excessive solder accumulation on pins which could cause a short between the pin and the microphone plug housing When all soldering connections to the pins of the microphone plug are complete push the knurled ring and the housing forward and screw the housing onto the threaded portion of the pin receptacle body Note the location of the screw clearance hole in the plug housing with respect to the threaded hole in the pin receptacle body When the housing is completely threaded into the pin receptacle body a final fraction of a turn either clockwise or counterclockwise may be required to align the screw hole with the threaded hole in the pin receptacle body When these are aligned the retaining screw is then screwed into the place to secure the housing to the pin receptacle body The two cable clamp retainer screws should now be tightened to secure the housing to the microphone cord If the cutting directions have been carefully followed the cable clamp should secure to the insulating jacket of the microphone cable Upon
14. se or ambient backgrounds noise is eliminated Turn fully counterclockwise then slowly clockwise until the receiver noise disappears Any signal to be received must now be slightly stronger than the average received noise Further clockwise rotation will increase the threshold level which a signal must overcome in order to be heard Only strong signals will be heard at a maximum clockwise setting MIC GAIN inner dual concentric Adjust the microphone gain in the transmit and PA modes This controls the gain to the extent that full talk power is available several inches away from the microphone RF GAIN CONTROL outer dual concentric Use to reduce the gain of the RF amplifier under strong signal conditions 8
15. to you Since we use UPS and they do not ship to Post Offices boxes please provide us with a street address for the return of your radio We will repair and return your radio as soon as we can We appreciate your choosing a Galaxy radio and we want you to be on the air as much as possible Be sure to visit our web site at www GalaxyRadios com Printed In Malaysia AT3601014H PD000802 axXY DX 33HML Full Channel AM FM Mobile Transceiver OWNER S MANUAL TABLE OF CONTENTS Specification s enseri Ree ee OAS ERE SES be ees Installation LOCaON se soap ep ke repan RO d wating uae a nai Mounting the Connection 00 eee ee Ignition Noise Interference 05 AMICNN A o 5 c oats ae pele eae his he gine ese ated Tuning the Antenna for Optimum SWR External Speaker 0 0 22 eee eee eee ee Operation Control Functions 0 c eee eee eee eee A Front Panel 3 2 ods ei4 ekdte cat pimeni einne B Rear Panel 3 4 0c50 e25s bbs beh bei Cw eA Press To Talk Microphone 2 005 Operating Procedure to Receive Operating Procedure to Transmit Alternate Microphones and Installation Page 10 11 11 11 12 fe nA SoN Aa Fig 3 Microphone plug pin numbers viewed from rear of pin receptacle Be sure that the housing and the knurled ring of Fig 2 are pushed back onto the microphone cable before starting t
Download Pdf Manuals
Related Search