EV-DW4955 Mini Door Sensor
Contents
1. The EV DW4955 requires one Renata CR2450N lithium battery To replace the battery remove the cover as indicated in Figure A Once cover is removed the battery will be visible To remove battery insert a flathead screwdriver under the battery and gently twist please refer to Figure D for details Wait 90 seconds then install the new battery placing positive side up WARNING cad may explode if mistreated Do not recharge disassemble or dispose of in fire PAGE 3 This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment FIGURE D EV DW4955 with back cover off Tamper location Insert screwdriver here gently twist Battery side up PC Board Federal Communications Commission FCC Statement This equipment has been tested to FCC requirements and has been found acceptable for use The FCC requires the following donei our information This sual ed generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause rea ane to radio and television reception It has bee2. Unauthorized el or modifications could void the user s authority to operate the equipment PAGE 4
3. Technical Support 866 908 TECH EV DW4955 Wireless Mini Door Window Contact USER MANUAL Powering the EV DW4955 For your added convenience the EV DW4955 comes with the battery pre installed To activate hold the EV DW4955 firmly in one hand and pull the plastic tab in the direction indicated Locate Transmitter Select the location where the EV DW4955 is to be mounted NOTE RF signals can be affected by metal objects including metal doors or large mirrors Such locations should be avoided as they can interfere with proper operation Enrolling Programming and Placement Enroll the EV DW4955 by programming the 6 digit serial number located on the EV DW4955 into the receiver Once the EV DW4955 is enrolled you must perform a Module Placement test to ensure the location you have chosen is suitable Please refer to your receiver Installation Manual for details Mounting the EV DW4955 and Magnet Once you have determined the proper location see Enrolling Programming and Placement the EV DW4955 can be permanently mounted NOTE It is the responsibility of the installer to ensure that the EV DW4955 is securely mounted in the intended location PAGE 1 Using Provided Screws Remove the back from the transmitter Figure A Mount the back housing of the EV DW4955 using the screws supplied to the desired location To remove cover insert screwdriver here and gently twist FIGURE A Using Adhesive Tape E
4. n type tested and found to comply with the limits for a Class B computing Het in accordance with the specifications in Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interferences to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference By one or more of the following measures e If using an indoor antenna have a quiy outdoor antenna installed e Reorient the receiving antenna until interterence is reduced or eliminated Move the receiver away from the control communicator Move the antenna leads away from any wire runs to the control communicator e Plug the control communicator into a different outlet so that it and the receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user or installer may find the following booklets prepared by the Federal Communications Commission helpful Interference Handbook This booklet is available from the U S Government Printin office Washington DC 20402 The user shall not make any changes or modifications fo the equipment unless authorized by the installation instructions or User s Manual
5. nsure that the surface is clean and dry Apply the tape to the back of the EV DW4955 press and hold firmly in the desired location for approximately 10 15s It can take up to 24h for the tape to reach maximum bonding strength Align the magnet with the notched arrow on the EV DW4955 housing see Figure B Mount the magnet q maximum of 5 8 1 8cm from the EV DW4955 by using the Aided tape or screws If necessary use the spacers provided Once the EV DW4955 and magnet are mounted open and close the window door to ensure that none of the parts interfere with this movement Only one magnet can be used for each EV DW4955 NOTE The adhesive tape is not to be used in UL Installations 5 8 space max 1 8cm A Reed switch on Symbol on side of underside of PC the case indicates Board in unit location of reed switch PAGE 2 Tamper Switch Out of the box the EV DW4955 comes equipped with case tamper detection If the case is removed the EV DW4955 will report a zone tamper to the control panel For added security the EV DW4955 was designed fo provide wall tamper monitoring as well Simply replace the short rubber actuator see Figure C with the longer one that is included With this option if the case is opened or if the EV DW4955 is removed from it s location a tamper will be sent to the control panel It is strongly recommended that mounting screws be used when using the wall tamper option FIGURE C Replacing the Batter
Download Pdf Manuals
Related Search