User`s Guide - Ballicom.co.uk
Contents
1. Status LEDs 3 With the contacts on the bottom and the arrow pointing toward the LEDs place a battery into one of the bays 4 Slide the battery towards the LEDs The battery snaps into place If the battery is not charged the Status LED for that bay turns red The Status LED turns green when the battery is charged PB3 Mobile Printer User s Guide Battery Safety Information Follow these tips for maintaining the PB3 battery Be sure to fully charge the battery before long printing sessions such as printing receipts with many bar codes and graphics For maximum battery life Intermec recommends charging the battery at 25 C 77 F Remove the battery from the printer before storing the printer for long periods of time The battery storage temperature is 20 C to 40 C 4 F to 104 F Do not store a fully charged battery at temperatures greater than 40 C 104 F for long periods of time the battery may permanently lose charge capacity Dispose of battery according to local regulations Do not throw in trash Do not disassemble short circuit heat above 80 C 176 F or incinerate The battery may explode For more information see the PB2 and PB3 Battery Instructions Loading Paper To prevent possible damage to the print mechanism use only receipt paper rolls that are not fastened to the inside core in any Caution way Otherwise the core will be pulled into the mechanism causing jamming and possib2. compartment first The contact end drops into place Be sure you insert the battery correctly or you may damage the battery contacts in the printer Caution 4 Close the battery door and slide the latch away from the belt loop knob to lock the latch 4 PB3 Mobile Printer User s Guide To remove the battery Unlock and open the battery door and tip the printer to one side to remove the battery To charge the battery with the AC adapter charger 1 2 UJ e Plug the AC adapter into the power connector Install the appropriate AC plug on the adapter The adapter comes with four different plugs suitable for most regions worldwide Make sure the printer is off and connect the adapter to AC power The Battery LED turns on indicating that the battery is charging Note If the other LEDs turn on press the Power button to turn the printer off After about three hours the Battery LED turns off The battery is fully charged Note The wall mounted charger is Class II equipment Multiple plug configurations comply with most international standards The wall mounted charger is not supplied with plugs for use in Korea PB3 Mobile Printer User s Guide Using the 2 Bay Battery Charger Use the 2 bay battery charger to charge the batteries To use the 2 bay charger 1 Plug the AC adapter into the 2 bay charger 2 Connect the adapter to AC power The Status LEDs turn green indicating that the charger is ready to use
3. Battery Door Latch The printer features are described in the next table PB3 Feature Descriptions Feature Description Power button Press once to turn the printer on or off Feed button Press to feed paper out of the printer You can also press Feed to print a configuration test page For help see Printing a Configuration Test Page on page 10 Paper door handle Pull to open the paper compartment door For help see Loading Paper on page 7 Power connector Connects the printer to the AC adapter battery charger For more information see the next section Serial port Connects the printer to a host computer Use cable P N 5892RJD9 1 Battery door latch Slide to lock or unlock the battery door For help see the next section Belt loop knob Attaches the printer to the included belt loop For help see Using the Belt Loop on page 9 PB3 Mobile Printer User s Guide Understanding the LEDs PB3 LED State Descriptions LED Communications Battery Data and Status PB3 Mobile Printer User s Guide State Flashing Green Steady Green Flashing Blue Steady Blue Steady Red Off Steady Amber Off Steady Green Flashing Red Steady Red Battery LED Communications LED Data and Status LED Description Power is on PB3 is in RS 232 mode PB3 is communicating with host in RS 232 mode Power is on PB3 is in Bluetooth or 802 11 mode PB3 is communicating via Bluetooth or 802 11 radio
4. Low battery charge Battery fully charged when printer is connected to AC power Battery is charging Card was read successfully or card cannot be read for optional magnetic stripe reader Card reader is ready to accept data for optional magnetic stripe reader Printhead is too hot Printing is paused until printhead reaches normal operating temperature One of three conditions Printer is out of paper The paper door is open Card reader error for optional magnetic stripe reader Using the Battery and AC Adapter Charger Use Intermec battery model 318 040 001 only Use of another battery may present a risk of fire or explosion Caution The battery used in this device may present a fire or chemical burn hazard if mistreated Do not disassemble heat above 80 C 176 F or incinerate capacity To cycle a battery fully charge it and then allow a full discharge through normal use To ensure a full charge do not operate the printer while charging the battery Note The battery must be cycled several times to achieve maximum To install the battery 1 Slide the battery door latch toward the belt loop knob to unlock the battery door and open the battery door to an angle of about 90 degrees Do not force the door all the way open N Orient the battery so the arrow points toward the battery contacts in the battery compartment UJ Insert the end of the battery without contacts into the battery
5. PB3 Mobile Printer User s Guide Installing Printer Firmware When you install printer firmware you also need to configure your printer hardware Before getting started make sure that your printer is set to serial mode all DIP switches are off the paper roll is properly seated on your printer your printer is connected to your host PC with a serial cable LED 1 is on green you have the Tera Term application installed on your host PC Tera Term is a free open source terminal emulator program available from the Internet you have the Tera Term macro ConfigurationHardwareInformationTTMacro ttl installed on your PC You can download the macro from the PB3 downloads page from the Intermec web site at www intermec com To install firmware and configure printer hardware i Use only firmware files provided by Intermec Caution e 1 Print a configuration test page For help see Printing a Configuration Test Page on page 10 Configure the printer for a serial connection and connect it to the host computer with a serial cable For help see Setting Up Serial Communications on page 13 Open a communications program such as HyperTerminal or Tera Term The printer turns on when the program connects to the printer Note If the printer does not turn on you need to cycle power to the printer Remove and install the battery or unplug and connect the AC power connector As soon as you see the text boot loader v1 xx
6. Version Number Date Description of Change 002 06 2009 Clarified DIP switch settings updated software and programming information and added part numbers for the 2 bay battery charger and VBA accessories PB3 Mobile Printer User s Guide iii PB3 Mobile Printer User s Guide Contents Contents Before you Begin ted bak dod EE ub bos RR EE vii Safety Informations ves bck ies header ages eee IEEE EXP de SE eg vil Global Services and Support vil Warranty Information vii Web Supports Losses dave a UV E C eR PER DO du viii Telephone S ppoft urs euer vn eet ek e E viii Service Location Support Vill Who Should Read This Manual ix Related Documents gere AE oes Robe de Rh Awe ed Od ara ix Learning About the PB3 Mobile Prnrter esee 1 Understanding the Printer Features 1 Understanding the LEDs ieoi drina A R A E ARARE 3 Using the Battery and AC Adapter Charger soret xro a arkir eee eee 4 Using the 2 Bay Battery Charger rers are Enan esee 6 Loading Paper oer eto ads aa EROT al gel gee ORY obed i Tearing Papers eve wee sce dan dears wales E 9 Usinethe BeltLo0pucsc c ese date ce Ee pia bi teehee dt 9 Printing a Configuration Test Page 10 Communicating With a Host isses m 11 Setting Up Bluetooth or 802 11 Communications 4 12 Setting Up Serial Communications 13 Changing Printer Connection Settings 13 Using the Magnetic Stripe Reader 16 Maintaining the Printer ie dog met RE
7. knob out of the slot Note Do not try to remove the printer from the belt loop without O pressing both latches Printing a Configuration Test Page Once the battery is charged and paper is loaded you can print a configuration test page Use this information for reference when installing the PB3 and to verify correct printer operation If you cannot print the test page see Troubleshooting on page 18 printer will not print unless a battery is installed Note If you are using the AC adapter charger as a power source the To print a test page 1 Make sure the printer is off before you begin 2 Press and hold the Feed button 3 Press the Power button once to turn on the printer When the printer starts printing the test page release the Feed button 4 To stop or cancel printing the test page press either the Power or Feed button 10 PB3 Mobile Printer User s Guide Model Number PBXAO21E Serial Number 312R0800001 Device Address si 0012F305F6AA H III Intermec Sample Configuration Test Page Communicating With a Host Depending on the configuration you ordered the PB3 supports either a Bluetooth or 802 11g wireless network connection to a host computer that will send data for the printer to print You can also configure the PB3 to use a serial connection instead For more information on configuring serial connections see Changing Printer Connection Settings on pag
8. press Backspace This message appears Erase user code PB3 Mobile Printer User s Guide 21 Press Y This message appears Erasing Erased Internal Bank O0 Erased External Flash Chip Send a Hex File Send the firmware file to the printer The printer loads the new firmware which takes 4 to 5 minutes When the firmware is loaded the printer responds with Done Start the Tera Term application From the Setup menu select Serial port 9 Configure the serial port settings as shown 10 11 12 13 14 15 22 x Port M Baud rate uszo Data Jet v Cancel Parity noe zl Stop En d Help Flow control xonjxoff Transmit delay 0 msec char 0 msecjline HAE Click OK Select Control gt Macro Browse to the location of the ConfigurationHardwareInformationTTMacro ttl file Select and open the file In the Enter Printer MODEL Number field enter the printer model number from the configuration test page and click OK In the Enter Printer SERIAL Number field enter the printer serial number from the configuration test page and click OK PB3 Mobile Printer User s Guide 16 In the Enter Wireless DEVICE Address field enter the wireless device address from the configuration test page and click OK When the hardware configuration process is done the Flash load message and bootloader message appear w Tera Term COM1 VT i sl o x File Edit Setup Control Win
9. select Printers and Media 4 In the Product Family field select Mobile Printers 5 In the Product field select PB2 PB3 Commercial Mobile Receipt Click Submit n 7 From the list of available downloads select the Easy Configuration Utility and follow the prompts to download the application 12 PB3 Mobile Printer User s Guide Setting Up Serial Communications For a serial connection to the host computer you need to e configure the PB3 for a serial connection For help see the next section e connect the PB3 to the host using the optional serial cable P N 5892RJD9 1 For pinouts see Accessories on page 25 To host computer Serial cable PB3 With Serial Cable Changing Printer Connection Settings Connection settings are changed by the DIP switches located inside the battery compartment Follow the next procedure to change DIP switch settings Use caution when changing DIP switch settings Carefully use a Pointer on the dip switch to toggle its position Do not use a screwdriver and do not apply excessive force aution PB3 Mobile Printer User s Guide 13 To change printer settings with the DIP switches 1 Open the battery door and remove the battery The DIP switches are located inside the battery compartment DIP switches Or r1 y The DIP switches are numbered 1 to 8 from left to right By default all DIP switches are off toggled away from the configuration la
10. EUR Ue Ee ded 16 Troubleshooting s ted sene rb pe XR viari 18 Problems and Sol tions u a e d ooh beatae ne clea Bowes dE URSI 18 Calling Product Support soirs s oie pr AE BEE la n eck bee Gs 19 Software and Programming Intormmaron reire eea EEE E E Ta EA 20 Downloading Printer Software 20 Installing Printer Firmware 2000000000000 en ees 21 Specificationis o 6 cit aedvnd Peleus ide epp DOM e ebe 24 AGCESSOLIES s e Noahs Vm RE RR E VN CAR OUR Peu RU ES 25 PinoutDiagtam ende ERR ROREM I Oben IMPO he dpe wens ees 25 PB3 Mobile Printer User s Guide v Contents vi PB3 Mobile Printer User s Guide Before You Begin Before You Begin This section provides you with safety information technical support information and sources for additional product information Safety Information Your safety is extremely important Read and follow all warnings and cautions in this document before handling and operating Intermec eguipment You can be seriously injured and eguipment and data can be damaged if you do not follow the safety warnings and cautions This section explains how to identify and understand warnings cautions and notes that are in this document A caution alerts you to an operating procedure practice condition or statement that must be strictly observed to prevent eguipment damage or destruction or corruption or loss of data aution condition or statement that must be strictly observed to avo
11. al 937 014 xxx ESC P Programmer s Reference Manual 937 010 xxx The Intermec web site at www intermec com contains our documents as PDF files that you can download for free To download documents 1 Visit the Intermec web site at www intermec com 2 Click Support Manuals 3 Use the Product Category field the Product Family field and the Product field to help you locate the product whose documentation you want to download PB3 Mobile Printer User s Guide ix Before You Begin x PB3 Mobile Printer User s Guide Learning About the PB3 Mobile Printer The PB3 Mobile Printer is a full featured portable receipt printer designed for a variety of job environments where point of service receipts are required The package contains e PB3 Mobile Printer AC adapter charger e Battery e Belt loop e Roll of 3 inch receipt paper already loaded in the printer Printhead cleaning pen e Product documentation Quick Start Guide Compliance Inserts Battery Instructions and Warranty Card For a list of PB3 accessories see Accessories on page 25 Understanding the Printer Features The next illustrations show the PB3 controls and ports Power button if C C 2 Feed amp button 5 Power Ba connector P Te 7 Paper door handle PB3 Controls and Power Connector PB3 Mobile Printer User s Guide Belt loop knob Battery door latch Serial port PB3 Serial Port Belt Loop Knob and
12. atus as described in Understanding the LEDs on page 3 Cleaning cards for the magnetic stripe reader are available from Intermec For information contact your local Intermec distributor Maintaining the Printer 16 To clean the exterior of the printer use a soft cloth and mild cleaner Do not use abrasive cleaner chemicals or scouring pads as these will damage the finish PB3 Mobile Printer User s Guide When you load a new roll of paper or when voids in the printout are apparent clean the printhead and platen roller as described next Do not use sharp objects to clean the printhead This may damage the printer and reguire service or repair Caution To clean the printhead and platen roller 1 Remove the paper from the printer For help see Loading Paper on page 7 Printhead Black mark sensor Platen roller Tear bar 2 Clean the printhead with the included cleaning pen or with a cotton swab moistened with isopropyl alcohol 3 Remove buildup from the black mark sensor and tear bar with a cotton swab moistened with isopropyl alcohol 4 Turn the platen roller with your finger and run a dry cloth small brush or cotton swab moistened with isopropyl alcohol across the roller Ensure that the roller is clean all the way around Note Dust build up may occur depending on the environment K and the quality of the paper supply used Use a can of compressed air to blow dust and paper debris out of the printe
13. bel inside the battery compartment except for switch 2 PB3 Mobile Printer User s Guide 2 Change DIP switch settings by carefully pressing a pointer into the switch and sliding it to the other side For more information see the next table DIP Switch Settings Turn These DIP Switches On To Set This Parameter 1 2 34 5 6 7 8 Enable serial connection Enable 802 11 connection X X Enable Bluetooth connection X Set baud rate 115200 57600 X 38400 X 19200 X X 14400 X 9600 X X 2400 X X 1200 X X X Parity Bit Enabled X Disabled no parity Odd Even Parity Bit Even X must be Enabled Odd Auto Power Save Enabled X Disabled Note If you are configuring the PB3 for a Bluetooth or 802 11 O connection make sure DIP switches 3 4 and 5 are off 3 Install the battery in the printer and close the battery door The printer is now configured for your connection PB3 Mobile Printer User s Guide 15 Using the Magnetic Stripe Reader e If your PB3 includes the optional magnetic stripe reader follow the next procedure to read cards Note You need an application running on the host computer to read data from the card For more information see the XSim Programmers Reference Manual PB3 Magnetic Stripe Reader Slot To use the magnetic stripe reader 1 Position the card so the magnetic stripe faces the paper door 2 Quickly swipe the card through the reader in either direction The Data and Status LED indicates card reading st
14. dow Help bootloader v1 32 Entering user s code FiLoadSize 8000D X0 bootloader v1 32 Entering user s code Tera Term Would you like to configure another printer Cw 17 Print a configuration test page For help see Printing a Configuration Test Page on page 10 18 Make sure that the Model Number Serial Number and Device Address on the test page you printed in Step 17 matches the information on the test page you printed in Step 1 PB3 Mobile Printer User s Guide 23 Specifications PB3 Mobile Printer Specifications Specification Height Width Length Weight with battery and paper Power Operating temperature Storage temperature Operating humidity Storage humidity Printhead Print method Print speed Character sets Supported bar codes Memory Charge time Communications Print ratio 24 Description 57 mm 2 25 in 120 mm 4 75 in 152 mm 6 in 0 58 kg 1 3 Ib 7 4 V Li ion battery 2200 mAH 10 C to 509C 14 F to 122 F 20 C to 60 C 4 F to 140 F 20 to 85 non condensing 5 to 95 non condensing 80 mm 3 in wide 203 dpi 8 dots mm Direct thermal Up to 5 6 cm sec 2 in sec Standard English Latin Optional Arabic Simplified Chinese Traditional Chinese Cyrillic Greek Hebrew Polish Codabar Code 39 UCC EAN 128 EAN UPC Interleaved 2 of 5 Code 128 PDF417 1 MB RAM 4 MB program flash Approximately 180 min Serial RS 232 Blueto
15. e 13 PB3 Mobile Printer User s Guide 11 Setting Up Bluetooth or 802 11 Communications If your PB3 includes the optional Bluetooth module the printer is configured by default for Bluetooth connections at a baud rate of 115200 The PB3 cannot initiate a Bluetooth connection You must connect to the PB3 from a host such as a handheld computer See the documentation for your computer for more information on connecting to Bluetooth devices communications the printer stays on all the time unless you have enabled the automatic power save feature When power save is enabled the printer turns off if no communications are received from the host for 99 seconds To enable automatic power save see Changing Printer Connection Settings on page 13 Note When the printer is set for Bluetooth or 802 11 The unigue Bluetooth Device Address BDA for the printer is printed on the battery door certification label If your PB3 includes the optional 802 11g radio module the printer is configured by default for an 802 11g wireless network connection The unigue MAC address for the printer is printed on the battery door certification label Use the PB2 amp PB3 Easy Configuration Utility to configure Bluetooth and 802 11 settings For more information see the utility online help To download the Easy Configuration Utility 1 Go to the Intermec web site at www intermec com 2 Select Support Downloads 3 In the Product Category field
16. fatermec PB3 Mobile Printer Intermec Technologies Corporation Worldwide Headguarters 6001 36th Ave W Everett WA 98203 U S A www intermec com The information contained herein is provided solely for the purpose of allowing customers to operate and service Intermec manufactured equipment and is not to be released reproduced or used for any other purpose without written permission of Intermec Technologies Corporation Information and specifications contained in this document are subject to change without prior notice and do not represent a commitment on the part of Intermec Technologies Corporation 2008 2009 by Intermec Technologies Corporation All rights reserved The word Intermec the Intermec logo Norand ArciTech Beverage Routebook CrossBar dcBrowser Duratherm EasyADC EasyCoder EasySet Fingerprint i gistics INCA under license Intellitag Intellitag Gen2 JANUS LabelShop MobileLAN Picolink Ready to Work RoutePower Sabre ScanPlus ShopScan Smart Mobile Computing SmartSystems TE 2000 Trakker Antares and Vista Powered are either trademarks or registered trademarks of Intermec Technologies Corporation There are U S and foreign patents as well as U S and foreign patents pending Bluetooth is a trademark of Bluetooth SIG Inc U S A ii PB3 Mobile Printer User s Guide Document Change Record This page records changes to this document The document was originally released as Revision 001
17. hot and printer has automatically paused the current print job Check the AC adapter output with a multimeter Output should be 10 VDC f AC output is OK there is a problem with the battery or battery charge circuit IFAC output is not OK replace the adapter PB3 Mobile Printer User s Guide PB3 Problems and Solutions continued Problem Solution Battery life is short aftera Replace the battery full charge In Bluetooth mode Move the printer closer to the host printer does not print data Make sure the host has established a connection from host with the printer Calling Product Support Ifyou cannot find the answer to your problem at Knowledge Central or in the PB3 Problems and Solutions table you may need to call Intermec Product Support To talk to a Product Support representative in North America or Canada call 1 800 755 5505 Outside the U S A and Canada go to www intermec com and click Contact to find your local Intermec representative Before you call Intermec Product Support make sure you have the following information ready Serial number e Firmware version Bluetooth or serial communication settings such as baud rate Some printer settings are included on the configuration test page For help see Printing a Configuration Test Page on page 10 Visit the Intermec technical knowledge base Knowledge Central at www intermec com and click Support Knowledge Central to review technica
18. id I A warning alerts you of an operating procedure practice death or serious injury to the persons working on the equipment Warning Note Notes either provide extra information about a topic or contain O special instructions for handling a particular condition or set of circumstances Global Services and Support Warranty Information To understand the warranty for your Intermec product visit the Intermec web site at www intermec com and click Support gt Returns and Repairs gt Warranty PB3 Mobile Printer User s Guide vii Before You Begin viii Disclaimer of warranties The sample code included in this document is presented for reference only The code does not necessarily represent complete tested programs The code is provided as is with all faults All warranties are expressly disclaimed including the implied warranties of merchantability and fitness for a particular purpose Web Support Visit the Intermec web site at www intermec com to download our current manuals in PDF To order printed versions of the Intermec manuals contact your local Intermec representative or distributor Visit the Intermec technical knowledge base Knowledge Central at www intermec com and click Support Knowledge Central to review technical information or to request technical support for your Intermec product Telephone Support In the U S A and Canada call 1 800 755 5505 Outside the U S A and Canada contact your l
19. l information or to request technical support for your Intermec product PB3 Mobile Printer User s Guide 19 Software and Programming Information Intermec offers a variety of printer software such as applications utilities and periodic firmware updates Downloading Printer Software 20 You can download printer software from the Intermec web site To download printer software 1 Go to the Intermec web site at www intermec com 2 Select Support gt Downloads 3 In the Product Category field select Printers and Media 4 In the Product Family field select Mobile Printers 5 In the Product field select PB2 PB3 Commercial Mobile Receipt Click Submit 7 From thelist of available downloads select a file name and follow the prompts to download the file n The PB3 is compatible with the XSim printer language as well as with a subset of ESC P commands For more information see one of these manuals e XSim Programmer s Reference Manual ESC P Programmer s Reference Manual Intermec s Printing Resource Kit provides tools for developing mobile printing solutions for the PB3 For more information visit www intermec com and choose Products gt Applications amp Software gt Developer Library gt Developer Resource Kits Note You can also download SDKs from www fieldsoftware com to help develop mobile printing solutions for certain language sets e PrinterCE SDK es PrinterCE NetCF SDK e PocketHTMLprint SDK
20. le gear damage To load paper PB3 Mobile Printer User s Guide 1 Lift the paper door handle and pull it gently to open the door 2 Place the 3 inch paper roll into the printer as shown in the next illustration The paper supply should unwind from the bottom 3 Unroll about 3 inches of paper from the roll and position it between the printhead guides Printhead guide Printhead 4 Close the paper door The door clicks when completely closed 5 Fold the door handle flush with the printer PB3 Mobile Printer User s Guide 6 Press the Power button to turn the printer on 7 Press and hold the Feed button to verify that the paper advances correctly Tearing Paper Note Using the tear bar is the only way to tear the paper Pulling up o and pulling sideways without using the tear bar can cause a paper jam The paper door acts as a tear bar Pull one edge of the paper against the tear bar and then tear down and across against the tear bar to tear the paper The tear bar has sharp edges Be careful when tearing paper or A when handling the paper door Warning Using the Belt Loop 1 Place the belt loop over your belt and snap it to secure it PB3 Mobile Printer User s Guide 2 Insert the belt loop knob into the connector slot on the belt loop and slide the printer down until the knob clicks into place 3 To disconnect the printer from the belt loop press both of the connector latches and slide the belt loop
21. ocal Intermec representative To search for your local representative from the Intermec web site click About Us gt Contact Us Service Location Support For the most current listing of service locations go to www intermec com and click Support gt Returns and Repairs gt Repair Locations For technical support in South Korea use the after service locations listed below AWOO Systems 102 1304 SK Ventium 522 Dangjung dong Gunpo si Gyeonggi do Korea South 435 776 Contact Mr Sinbum Kang Telephone 82 31 436 1191 E mail mjyun awoo co kr PB3 Mobile Printer User s Guide Before You Begin IN Information System PTD LTD 6th Floor Daegu Venture Center Bldg 95 Shinchun 3 Dong Donggu Daegu City Korea E mail jmyou idif co kr or korlim gw idif co kr Who Should Read This Manual This document is for the person who is responsible for installing configuring and maintaining the PB3 Mobile Printer This document provides you with information about the features of the PB3 and how to install configure operate maintain and troubleshoot it Before you work with the PB3 you should be familiar with your network and general networking terms such as IP address Related Documents This table contains a list of related Intermec documents and their part numbers Document Title Part Number PB3 Mobile Printer Quick Start Guide 930 217 xxx PB2 and PB3 Battery Instructions 943 217 xxx XSim Programmers Reference Manu
22. oth 802 11g IrDA 25 black max sq in PB3 Mobile Printer User s Guide Accessories These accessories sold and ordered separately are available from Intermec Battery P N 318 040 001 AC Adapter Charger P N 157261 Charges the battery and runs the printer on AC power battery must be installed or printer will not print Shoulder Strap P N 757351 Printhead Cleaning Pen P N 757150 Magnetic Stripe Reader MSR Cleaning Cards P N 757160 Serial Cable P N 5892RJD9 1 3 inch Receipt Paper P N E24789 Belt loop P N 756998 2 2 Bay Battery Charger P N 767400 Vehicle Battery Adapter VBA cigarette lighter charger P N 852 043 004 Pinout Diaeram mr Pin1 Serial Port Pin Assignments Pin Signal Description 1 5 COM Logic common 2 3 4 6 TXD RS 232 from printer output RXD RS 232 from host input CTS Clear to send from printer output RTS Reguest to send from host input PB3 Mobile Printer User s Guide 25 26 PB3 Mobile Printer User s Guide Intermec Worldwide Headquarters 6001 36th Avenue West Everett Washington 98203 U S A tel 425 348 2600 fax 425 355 9551 www intermec com 2009 Intermec Technologies Corporation All rights reserved PB3 Mobile Printer User s Guide P N 934 043 002
23. r PB3 Mobile Printer User s Guide 17 Troubleshooting This section contains information about troubleshooting common problems and contacting Product Support Problems and Solutions Most printer operation print guality or printer communication problems can be fixed easily The next table includes some common printer problems and possible solutions 18 PB3 Problems and Solutions Problem Printer does not feed paper correctly Printer does not print Print guality is too light Voids appear in print Data and Status LED is steady red Data and Status LED is flashing red Battery LED does not turn on when printer is connected to AC adapter but printer will not turn on Solution Remove jammed paper and reload paper supply Make sure the paper supply is loaded correctly Install a battery The printer will not print unless a battery is installed even if you are using the AC adapter charger as a power source If you are unable to print from a host computer try printing a test page Verify that the communication settings from the test page are correct for your connection For help see Printing a Configuration Test Page on page 10 Check the battery and recharge it if necessary Adjust print contrast through the print application Clean the printhead Check the paper supply and make sure the paper door is closed properly Read error Try reading the card again Printhead may be too
Download Pdf Manuals
Related Search