English booklet version - Salus Controls
Contents
1. gives you specific legal rights and you may also have other rights that vary from jurisdiction to jurisdiction If you have any questions regarding this warranty please write Salus at 123 Townsend St Level LL2 San Francisco CA 94107 SALUS WARRANTY Salus Controls Inc Salus warrants that for a period of two 2 years Warranty Period from the date of purchase by the consumer Customer this device excluding batteries Product shall be free of defects in materials and workmanship under normal use and service in accordance with all supplied instructions During the warranty period Salus shall at its option repair or replace any defective Products at no charge for the device Any replacement and or repaired devices are warranted for the remainder of the original Warranty Period or ninety 90 days whichever is longer This warranty does not cover removal or reinstallation costs This warranty does not apply to any Product i which has been modified repaired or altered except by Salus or an authorized Salus representative ii which has not been maintained in accordance with any handling or operating instructions supplied by Salus or iii which has been subjected to unusual physical or electrical stress misuses abuse negligence or accidents This warranty is the only express warranty Salus makes for the Product Any implied warranties including warranties of merchantability or fitness for a partic2. OSALU S OPTIMA ZigBee Thermostat OSALU S Salus Controls Inc Quick Start Guide 123 Townsend St Level LL2 San Francisco CA 94107 eerste For other language versions please visit www salusinc com LET S GET STARTED Make sure you have the following items rely Thermostat with Trim plate Screws and Anchors Mounting Plate Heat Pum Gas or Electric HP Non HP CSD C Wiring label Wiring label SALUS R R RC RC cc RH RH L L c c a 23 OPTIMA ZigBee Thermostat Y1 Y1 Y1 Y1 Y2 Y2 Y2 Y2 wi wi wi wi O B i OIB w2 i w2 Quick Start Guide G G G G Wire Labels 2 x AA alkaline User s Manual Quick Start Guide batteries FCC and Industry Canada RF Radiation Exposure statement This equipment complies with FCC and Industry Canada RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20 centimeters between the antenna and all persons Industry Canada Under Industry Canada regulations this radio transmitter may only operate using an antenna of type and maximum or lesser gain approved for the transmitter by Industry Canada To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that necessary for successful communication This device complies with Indu
3. and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Turn off the heating and or cooling Turn OFF the breakers or remove the fuses to the heating and or cooling systems at the electrical panel In some regions there may be a switch located near the furnace Determine wiring configuration Heat Pump Gas or Electric HP Non HP e Remove the old thermostat to expose Wiring label Wiring label the wiring terminals R R RC RC e Take a picture of the wiring for future C c RH RH reference ae BE Y1 Y1 Y1 Y1 e Note the terminals attached to each Y2 Y2 Ta Y2 wire and attach the matching label to n ore re the ends of the wires Use the following O B O B w2 w2 table as a reference G G G G A jumper connects RC and RH as mos
4. ermostat The thermostat can now be used as a basic local thermostat To enable the enhanced features additional settings need to be configured such as pairing with a connected home system See the Configuring the Thermostat section in the User s Manual for more details
5. nto the back of the thermostat Make sure the polarity of the batteries is correct After inserting the batteries the display will flash all the segments followed by the version number of the firmware then display ua LH witha blinking wu Initial Configuration When configuring the thermostat press the or button or use the slider ring to cause the desired value to blink then press MODE to select the value Using the table at right select the country then the type of system After this configuration the thermostat will display the Home Screen and be ready for attachment to the Mounting Plate United States Configures thermostat for use in the US CA Canada Configures thermostat for use in Canada Heat Pump Non Heat Pump Gas electric or oil heat O Heat Pump with O reverse valve B Heat Pump with B reverse valve Attach Thermostat To Mounting Plate Attach the thermostat to the Mounting Plate by aligning the connector pins and the plastic retention posts and pushing the thermostat onto the Mounting Plate 3 Sooo Make sure the connector pins are not bent and that the thermostat is fully seated on the Mounting Plate Vaa eisa aana o ofo o o Turn Power Back On To The HVAC System Go to the electrical service panel or furnace switch and turn the HVAC system back on Configure Th
6. stry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Le pr sent appareil est conforme aux CNR d industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement 10 FCC Statements WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed
7. t combination heat and cooling systems use a single transformer For systems where separate transformers are used remove the a in place across the RC and RH terminals duration of implied warranties of merchantability or fitness so these exclusions or limitations may not apply to you No oral or written information or advice given by Salus or a Salus authorized representative shall modify or extend this warranty If any term is held to be illegal or unenforceable the legality or enforceability of the remaining terms shall not be affected or impaired Customer s sole and exclusive remedy under this limited warranty is product repair or replacement as provided herein If a Product under warranty is defective the Customer may e contact the party Seller from which the Customer purchased the Product to obtain an equivalent replacement product after the Seller has determined that the Product is defective and the Customer is eligible for a replacement or e contact Salus Service at 4700 Duke Drive Suite 200 Mason OH 45040 to determine whether the device qualifies for a replacement If a replacement is warranted and is shipped prior to the return of the device under warranty a credit card is required and a hold may be placed on the Customer s credit card for the value of the replacement until the returned device is verified as eligible for replacement in which case the Customer s credit card will not be charged This warranty
8. ular purpose are limited to the Warranty Period or the shortest period allowed by law SALUS SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND INCLUDING ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING DIRECTLY OR INDIRECTLY FROM ANY BREACH OF ANY WARRANTY EXPRESS OR IMPLIED OR ANY OTHER FAILURE OF THIS PRODUCT Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages or limitation on the TIP Wrap the wire ends Remove old thermostat terminals Remove the old thermostat wiring terminals from the wall taking care not to allow the wiring to fall inside the wall around a long stick such as a pencil to keep the wires from falling into the wall Install Mounting Plate Remove the Mounting Plate from the back of the Optima thermostat Use the included wall anchors and screws to attach the Mounting Plate to the wall making sure the wires run through the center opening Use the Trim Plate vertically or horizontally if desired Attach Wiring Before attaching the wires match the wire using the labels to its corresponding terminal Refer to the picture of the wiring taken earlier if necessary e Open the terminal by lifting the latch up e Push each wire into the hole of the terminal and push the latch down to secure the wire Install Batteries Insert the alkaline batteries i
Download Pdf Manuals
Related Search