Manual - EPA Systemy
Contents
1. USER MANUAL C S 64A Read this guide thoroughly and follow the installation and operation procedures carefully in order to prevent any damage to the unit and or any devices that connect to it This package contains 1 CS 64A Four Port Petite KVM Switch with Attached Cables 1 User Manual 1 Quick Start Guide If anything is damaged or missing contact your dealer Copyright 2003 ATEN International Co Ltd Manual Part No PAPE 1235 1AT Printed in Taiwan 08 2003 All brand names and trademarks are the registered property of their respective owners 2003 08 26 Note This eguipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This eguipment generates uses and can radiate radio freguency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this eguipment does cause harmful interference to radio or television reception which can be determined by turning the eguipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increa2. 2 Keyboard COMPUTERS The following eguipment must be installed on each computer that is to be connected to the system A VGA SVGA or Multisync video card A 6 pin mini DIN PS 2 style mouse port A 6 pin mini DIN PS 2 Style keyboard port CABLES For optimum signal integrity and to simplify the layout four high quality 4 in 1 CS Custom KVM cables have been designed into the CS 64A There is no need for a separate cable purchase Note The KVM cables have PS 2 style keyboard and mouse connectors The CS 64a does not support AT keyboards or serial mice 2003 08 26 FRONT VIEW 1 KVM Cables These 4 in 1 cables connect to the keyboard video mouse and audio ports on the computers you are installing see the Installation diagram on p 6 2 Port LEDs A LED lights to indicate its corresponding port is the one that has the KVM focus Depending on the port s status the LED may flash according to a specific pattern see the LED Display Table p 10 for details 3 Speaker Jack The cable from your speakers optional plugs in here 4 Console Ports Your keyboard monitor and mouse plug in here see the Installation diagram on p 6 Each port is marked with an appropriate icon to indicate itself 2003 08 26 INSTALLATION 1 Before you begin make sure that power to all the devices you will be connecting up have been turned off You must unplug the power cords of any c
3. HE PRICE PAID FOR THE PRODUCT FROM THE DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT DISK OR ITS DOCUMENTATION The direct vendor makes no warranty or representation expressed implied or statutory with respect to the contents or use of this documentation and specially disclaims its quality performance merchantability or fitness for any particular purpose The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions or update For further inquires please contact your direct vendor 14 2003 08 26
4. begin by invoking Hotkey Mode Invoking Hotkey Mode takes three steps 1 Press and hold down the Num Lock key 2 While Num Lock is down press and release the asterisk key or the minus key 3 Release the Num Lock key Num Lock or Num Lock Note The asterisk or minus key must be released within one half second otherwise Hotkey invocation is canceled When Hotkey Mode is active The keyboard Caps Lock and Scroll Lock LEDs flash in succession They stop flashing and revert to normal status when you exit Hotkey Mode Ordinary keyboard and mouse functions are suspended only Hotkey compliant keystrokes and mouse clicks described in the sections that follow can be input Pressing Esc or Spacebar exits Hotkey Mode 2003 08 26 SELECTING THE ACTIVE PORT Each CPU port is assigned a numeric Port ID 1 4 You can give the KVM focus directly to any computer on the installation with a Hotkey combination that specifies the ID of the port it is attached to The steps involved are 1 Invoke Hotkey Mode see p 7 2 Press and release the appropriate Port ID number 1 2 3 or 4 After you press the number the KVM focus switches to the designated computer and you automatically exit Hotkey Mode AUTO SCAN MODE The CS 64a s Auto Scan feature automatically cycles through the four ports at regular 5 second intervals This allows you to monitor the computer activity without havin
5. g to take the trouble of switching from port to port manually To start Auto Scan Mode 1 Invoke Hotkey Mode see p 7 2 Press and release A Once scanning begins it continues until you press Esc or Spacebar to exit Auto Scan Mode The Port that is active at the time scanning stops remains active Note 1 Auto Scan only scans ports that are powered on It passes over any powered off ports 2 While Auto Scan Mode is in effect ordinary keyboard and mouse functions are suspended You must exit Auto Scan Mode by pressing Esc or Spacebar in order to regain normal control of their use 3 Pressing Esc or Spacebar exits both Auto Scan Mode and Hotkey Mode 2003 08 26 SKIP MODE This feature allows you to skip from the currently active Port to the Previous or Next one with a single keystroke In contrast to Auto Scan Mode which switches Ports at a fixed interval you can dwell on a particular port for as long or as little as you like To activate Skip Mode 1 Invoke Hotkey Mode see p 7 2 Press lt to skip from the current port to the port that comes before it 3 to 2 2 to 1 etc 3 Press to skip from the current port to the port that comes after it 1 to 2 2 to 3 etc Note 1 Skip Mode remains in effect until you exit it You can use and gt as often as you like Ordinary keyboard and mouse functions are suspended only lt and gt can be input You m
6. omputers that have the Keyboard Power On function Otherwise the switch will receive power from the computer 2 To prevent damage to your equipment make sure that all devices you will be connecting up are properly grounded Refer to the Installation diagram on the next page as you perform the following steps 1 Plug your keyboard monitor mouse into the appropriate Console ports on the CS 64a Each port is labeled with an appropriate icon to indicate itself 2 Optional Plug your speakers into the CS 64a s speaker jack 3 Plug the attached KVM cables keyboard monitor mouse and speaker connectors into their respective ports on the computers you are installing After you have finished cabling up turn on the power to the computers Note The CS 64a s Power On default is to link to the first computer you turn on 2003 08 26 o J ENL JE wzm a I O TO EB ie 6 2003 08 26 OPERATION Accessing all of your computers from a single console could not be easier The CS 64a uses Hotkey combinations to give the KVM focus to the computer of your choice The CS 64A provides the following Hotkey features Selecting the Active Port Auto Scan Mode Skip Mode INVOKING HOTKEY MODE All Hotkey operations
7. se ports Serial mouse ports with adapters cannot be used Mouse needs to be reset Unplug the mouse from the Console Mouse Port then plug it back in Table continues on the next page 12 2003 08 26 Symptom Possible Cause Action Mouse Not Switch needs to be Turn off the computers and unplug the Detected or reset KVM cables Wait five seconds then Does Not plug the cables back in and turn the Respond computers on Correctly Mouse set to Serial Some mice can be set to act as either Mode a PS 2 or serial mouse Make sure the mouse is set to PS 2 mode Incorrect Mouse Check your Device Manager to be sure Driver that the correct driver for your mouse obtained from the manufacturer or supplied by the operating system has been installed Video Resolution and or Select a lower resolution and or Problems Bandwidth set too bandwidth high 1 The unit is designed to work with PS 2 keyboards XT 84 key and AT keyboards will not work 2 Some Notebooks notably the IBM Thinkpad and Toshiba Tecra have trouble when their mouse and keyboard ports are used simultaneously To avoid this only connect the mouse port or the keyboard port If you connect the mouse port you will need to use the notebook s keyboard when the notebook becomes the active computer 135 2003 08 26 LIMITED WARRANTY IN NO EVENT SHALL THE DIRECT VENDOR S LIABILITY EXCEED T
8. se the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that which the receiver is connected Consult the dealer or an experienced radio television technician for help Fe CE 2003 08 26 OVERVIEW The CS 64a Petite KVM Switch is a control unit that allows access to four computers from a single console keyboard monitor and mouse Before the development of the CS 64a the only way to control multiple computer configurations from a single console was through a complex and costly network system Now with a CS 64a Petite KVM Switch installation you can easily access four computers in a cost effective manner The CS 644 improves on previous models with a 50 smaller footprint and attached custom KVM cables The result is a neat and tidy workspace and trouble free installation Recognizing the increased importance of sound the CS 64a is speaker enabled You can listen to the audio output of all the computers one at a time on a single set of speakers Setup is fast and easy plugging cables into their appropriate ports is all that is entailed Simple Hotkey combinations control which computer has the KVM focus There is no software to configure no installation routines and no incompatibility problems Since the CS 64a intercepts keyboard input directly it works on any hardware platform and with all operating systems There is no better way
9. t Operating Temperature 0 50 C Storage Temperature 20 60 C Humidity 0 80 RH Noncondensing Housing Plastic Weight 0 9 kg Dimensions L x W x H 8 95 x 7 19 x 2 6 cm 11 2003 08 26 TROUBLESHOOTING Symptom Possible Cause Action Keyboard Not Responding Loose cables Check all keyboard cable connections to make sure they are completely seated in their sockets Keyboard needs to be reset Unplug the keyboard from the Console Keyboard Port then plug it back in Switch needs to be reset Turn off the computers Unplug the KVM cables Wait five seconds then plug the cables back in and turn the computers on Switch is in Auto Scan Mode Press the Spacebar to exit Auto Scan Mode Pressing Hot Keys Gets No Selected port connects to a Resend the Hotkey command selecting a port that has a powered On Response powered Off computer computer attached Hotkey seguence Resend the Hotkey command press input incorrectly and release each key in the seguence individually Switch is in Auto Scan Press the Spacebar to exit Auto Scan Mode Mode Mouse Not Loose cables Check all mouse cable connections to Detected or make sure they are completely seated Does Not in their sockets Respond r i i Correctly Use of Mouse Port This unit is designed to only work with Adapters PS 2 mice and computers with PS 2 type mou
10. to save time and money than with a CS 64 lt installation By allowing a single console to manage all of the computers the CS 64A eliminates the expense of purchasing a separate keyboard monitor and mouse for each Additionally it saves the extra space they would take up and eliminates the inconvenience and wasted effort involved in constantly having to move from one computer to the other 2003 08 26 FEATURES One console controls four computers Compact design features four attached 4 in 1 KVM keyboard video mouse and speaker cables Speaker enabled Easy to install no software required connecting cables to the computers is all it takes Easy to operate computer selection via Hotkeys Auto Scan function to monitor computer operation Hot pluggable add or remove computers for maintenance without powering down the switch LED display for easy status monitoring Keyboard and mouse emulation for error free computer booting Supports Microsoft IntelliMouse and the scrolling wheel on most mice Caps Lock Num Lock and Scroll Lock states are saved and restored when switching Superior video quality up to 2048 x 1536 DDC2B Compatible with all operating platforms Non powered 2003 08 26 HARDWARE REGUIREMENTS CONSOLE A VGA SVGA or Multisync monitor capable of the highest resolution that you will be using on any computer in the installation APS 2 Style Mouse A PS
11. ust exit Skip Mode in order to regain normal control of the console 2 Pressing Esc or Spacebar exits both Skip Mode and Hotkey Mode 2003 08 26 HOTKEY SUMMARY TABLE Combination Function Num Lock Port ID Switches access to the computer that or corresponds to that Port ID Num Lock A Invokes Auto Scan Mode e Switches access from the current port to the previous port gt Switches access from the current port to the next port Esc or Exits Hotkey Auto Scan and Skip Spacebar Modes LED DISPLAY TABLE Activity Indication Off Port is not selected On Steady Port is connected to an active computer Flashing On and Off equal Port is connected to an active computer and is being accessed in Auto Scan mode 10 2003 08 26 SPECIFICATIONS Function Specification Computer Connections 4 Port Selection Hot Keys LEDs Selected 4 Console Ports Keyboard 1 x 6 pin mini DIN female purple Mouse 1 x 6 pin mini DIN female green Video 1 x HDB 15 female blue Audio 1 x Earphone Jack speaker CPU Connectors Keyboard 4x 6 pin mini DIN male purple Mouse 4 x 6 pin mini DIN male green Video 4 x HDB 15 male blue Audio 4 x Earphone plug speaker Scan Interval 5 Seconds Video Resolution 2048 x 1536 DDC2B Environmen
Download Pdf Manuals
Related Search