DVDplay User Manual
Contents
1. But frame searching must still be enabled in order to set a frame number as the ending point on the disc Some software such as DVD Studio Pro must have a special parameter enabled in order to allow frames to be used as the end point 19 BAUD Rate The BAUD rate is the speed of the serial port on the DVD player that the DVDplay communicates with This needs to be set the same in both the DVDplay and in the player If they are not set the same nothing will work It is recommended that you set both of them to 9600 BAUD since this is the fastest speed which the DVDplay can communicate with the player Since Pioneer s players ship from the factory set at 4800 BAUD you must either remember to change it s setting or program the DVDplay for 4800 BAUD We highly recom mend setting them both at 9600 BAUD Do not set some channels at 4800 and others at 9600 since this will cause the channels to synchro nize at slightly different times This is because the commands take longer to get to the player at 4800 BAUD and the player then takes longer to react to them Synchronize In order for two or more channels of the DVDplay to synchronize with each other this option must be enabled in each of those channels Turn this off to disable a channel Squelch This is normally turned on If it is turned off then the player will display a still frame of the last frame in the loop while it is preparing to cycle back to the beginning then it will disp2. Many people prefer to see a black background during the rewind time Others might prefer white or some other color Here is how to change the background color of the Pioneer players 1 Turn off the synchronizer unplug the power cable if it is a non rack box and has no power switch 2 Turn on the player and stop the disc from playing 35 3 On the remote control is a button for Setup Simply press and release this button Do not hold it down since that might take you to the Advanced setup menu You want the Basic setup menu 4 Using the Right Arrow button on the remote control move across the various menu tabs until you get to the Video tab 5 Then use the down arrow button to get to Background Color 6 Hit Right arrow button and the screen should switch to the background color menu page 7 Now use the up and down arrows to select a color and use the left and right arrows to change the strength of that color With the various levels of Red Green and Blue you can set virtually any color that is possible on the screen 8 When you have the color you want hit the Enter button to accept the new background color 9 Now hit the Setup button Until you do this the new color has not been stored in the player If you were to turn off the player without hitting the setup button again the new color would be lost CHANGING BETWEEN NTSC AND PAL If you ordered your synchronizer with the
3. Wait another 2 seconds and then click the Load From Synchronizer button on the screen and go back to step 10 in these instructions 14 When you are done programming the synchronizer simply disconnect the cable and click on the Cancel button on the screen Then select Exit from the File menu to close the program Programming under DOS 1 Connect the DVDplay programming cable to a serial port on an IBM style PC computer If the computer only has one or two serial ports it doesn t matter which port you use If it has more than 2 then you must find out which ones are COM1 or COM2 PC type computers have serial ports with either 9 pin connectors or 25 pin connectors The DVDplay programming cable has a 9 pin serial connector If your computer is an old model with a 25 pin serial port you will need to get a 25 pin to 9 pin serial adapter They are available at most computer and electronic parts stores 23 2 Turn on the computer The DVDCUST software is a DOS program so if the computer comes up in Windows 3 x you need to close Windows by double clicking on the box in the upper left corner of program manager and answering yes when it asks if you want to end Windows You should not run a DOS shell under Windows 3 you should quit Windows If the computer comes up in Windows 98 and you plan to use the DOS program you need to restart in MS DOS mode Click on the Start button in the lower left corner of the task bar then select Shut Down t
4. When this option is installed it is done with a BNC connector on the back panel labelled B B Out or Sync Out depending on the case style Network Connector This can be used to connect multiple DVDplay synchronizers to each other to make a larger synchronizer It can also be used as a way to externally start the playback loop As long as this connector is shorted with a normally closed switch or a set of contact closures from a relay the synchronizer will not start playing it s loop Once the contacts are opened the synchronizer will start it s playback loop It will continue to play the loop even if the contacts are closed again but will not start the next loop if the contacts are closed by the time the synchronizer is ready to play the next loop The Network Connector is an RCA phono connector on the back panel 10 PART NUMBERS Option 1 B black burst out DVDplay _ IN _ Number of Channels Model 1 through 32 channels can fit in a single enclosure Option 2 N network I O external R rackmount for 2 or 3 trigger and expansion channels only 4 channels Note this used to be an and up come standard in option It is now standard rackmount boxes and do not on all models The N have the R in the model must appear in all model number numbers Examples DVDplay 2N eee basic 2 channel DVD synchronizer DVDplay 3N eee basic 3 channel DVD synchronizer DVDpla
5. soon as the software starts looking for the synchronizer One final possibility is that you are not using the correct programming cable Our programming cables are special cables with special connections There is no standard cable that matches this so you must use one made by us or made to match our specifications e Problem The program finds the synchronizer and starts to load the data from the synchronizer but it freezes and the program no longer responds Possible Cause This may be caused by an incompatablity between the operating system the computer s BIOS and the serial port hardware in the computer Some laptops such as the Dell Inspiron seem to do this a lot though we have seen it in various brands and even a small number of desktop computers In most cases you can still use the same computer by using our DOS software With Windows 98 you must restart the computer in MS DOS mode With Windows NT 2000 ME or XP you can open a Command Prompt window Start gt Programs gt Accesso ries gt Command Prompt and run the DOS software in that window The DOS software can set all of the same parameters as the Windows software It just uses a simpler text based interface e Problem When trying to load the data from the synchronizer into the program you get an error that says something like Bad Data in Synchronizer Possible Cause There are several possibilities The same problem as described in the previous prob
6. synchronizer you must tell the synchronizer that the channel is not to be used with other channels This is a simple process All you have to do is run the pro gramming software on the channel and disable the Synchronize parameter Using the Windows Software Run the windows software and connect the computer s serial port to the channel that you wish to disable Load the channel into the software the same as if you were changing the start or end points for that channel Find the checkbox on the screen labelled Synchronize and remove the check mark from it This sets that channel to work on it s own without synchronizing with the other channels After that this channel will not prevent the other channels from starting Effectively it is disabled Using the DOS Software Run the DOS software the same as if you were going to program the start or end points for that channel Use the arrow keys to move down to the parameter labelled Synchronize Hit the Enter key on the keyboard to change it from Enabled to Disabled Once it is 33 set as Disabled then that channel will no longer keep other channels from starting It will loop on it s own if you still use it but it won t be synchronized to the other channels If you ever need to use that channel again as one of the synchronizerd channels do not forget to re enable the Synchronize parameter You will be able to program a disabled channel at
7. this takes about 5 seconds 24 10 About 2 seconds after the lights change to orange hit the Enter key on the keyboard This runs the software It will now try to find the correct serial port and the DVDplay connected to it 11 If everything has been done correctly you should now see a list of the parameters programmed into the DVDplay as well as the list of commands available to you If instead you see some error messages or were returned to the DOS prompt check the cable connections and try again or see the troubleshooting chapter at the end of this manual 12 When you first start the program the first parameter in the list will be highlighted Use the up and down arrow keys on the keyboard to move the highlight from parameter to parameter until you get to the one you want to change See the Parameters To Change section before this section in this manual 13 When you have highlighted the parameter you wish to change hit the enter key on the keyboard For BAUD rate Synchro nize Squelch and the Start and End modes this will toggle between each of the choices For the number or text items this will then let you enter that parameter For number and text items simply hit the enter key again when done to accept the new data 14 Once you have set the parameters that you wish to change you must hit the S key on the keyboard to save the new parameters into the DVDplay Until you hit the S key the new parameters have not
8. allows you the most precise control over where to start the loop though searching on a frame number may take longer than searching on a title or a chapter This means that the pause between the end of a loop and the start of the next loop will be a second or two longer In order to use frames as a start point on the synchronizer your discs must be authored with frame searching enabled If you are able to use the remote control to search manually to a specific frame then the synchronizer can also be programmed to start on a specific frame End Mode You can end the playback loop on a specific Title Chapter Timecode if the disc has it or Frame Number Use the End Mode to specify which of these you will use Like with the start mode 18 you can only define an end mode if that item exists on the disc So if the disc does not allow chapter searches you can not use chapters The same holds true for using time code or frames as the end mode End Title Since a DVD disc can contain several titles you can use this to tell the DVDplay to play up to the specific title This is useful if you want to play several titles in a row within your loop This param eter is only used if the End Mode is set to Title and there is an additional title on the disc after the one used in the start title End Chapter Since each title on a DVD disc can contain several chapters you can use this to define an ending point at a specific chapter This is
9. before it is used This can be done by us if you request it while ordering or you can follow the instructions in this booklet to program it yourself The software is currently only available for PC computers An RS 232 port is required to do the programming and Mac computers have not had an RS 232 port for a number of years There are two pieces of software included with the DVDplay synchronizers and available for download on our web site One is meant to be run under Windows operating systems such as Windows 95 Windows 2000 Windows XP etc The other is meant for MS DOS computers However the DOS version of the software also works in a command prompt window in Windows 2000 ME and XP It can also be used in a Windows 95 or 98 system by restarting the computer in MS DOS mode So if there are any problems getting the Windows software to work you can always try the DOS version of the software It has all of the same features It just has a text based interface rather than the mouse oriented GUI of the Windows version If you downloaded the software from our web site there were two choices for the Windows software You can download the Pro gram Only or the Full Install You have the same choices with the disk that is supplied with the synchronizer You can install just the program itself which lets you run the software to program a synchro nizer but it doesn t place the program in your Start gt Programs list Wi
10. multiple DVDplay synchronizers together to act as one large one connect them together using standard audio RCA phono cables between the Network connectors on the back of each synchronizer If you are connecting 2 units simply run a single cable between the Network Connector on each unit If you are connecting more than 2 you need to use RCA Phono Y adapters to split the cables so they can loop through each Network Connector connecting all of them together 7 Turn on the power for the synchronizer and all of the players 8 That s all About seven seconds after the DVDplay has been turned on it will take over control of the DVD players and the cycle will begin If there are no discs in the DVD players the DVDplay will open the drawers and wait for you to insert them If you power up the DVD players slowly or if you have to insert the discs into the players after powering up you may have to hit the reset switch on the DVDplay after the players have gotten up to speed If you do this there will be a 7 second pause and then the players will reset and a cycle will begin 9 When you are done for the day there are two ways to shut down The best way is probably to hold the reset switch down on the DVDplay while hitting the stop buttons on the players When they have all stopped then turn their power off The other way and the only way if you have locked out the front panel is to simply hit the power switches on the front of each
11. player It is not recommended that you simply turn off the power strip or throw the circuit breaker while discs are playing as this does not allow the player to shut down correctly We know of a number of people who simply turn the power off at the end of the day and they have had no problems but this is not the way Pioneer recommends they be turned off Be aware that the player s head might be over your disc and any movement of the player could damage your disc See the previous section on setting up the player to 31 read about the Weekly Timer that is built into the player It can be used to safely and automatically turn the players on and off at specific times each day If you use that you can simply leave the synchronizer on all the time it won t hurt it and the synchronizer will take control of the players as soon as they power themselves up 32 Chapter 5 Miscellaneous INTRODUCTION This chapter covers various subjects about using the synchro nizer in special ways Everybody has a slightly different idea of what they want to do with synchronized video The synchronizer was designed to fit as many of these different uses as possible DISABLING A CHANNEL There are times when you might not want to use all of the channels in a synchronizer Normally an unused channel will prevent other channels from starting since the synchronizer assumes that the player just has not yet become available To disable a channel on the
12. put the disk in your floppy drive double click on My Computer then double click on 3 1 2 Floppy then double click on the DVDsynce folder and finally double click on the DVDsync exe icon 6 Once DVDsync opens go to the Synchronizer menu and select Find Synchronizer 7 You must select the serial port that you have connected the programming cable to 22 8 Click on the Find Now button and hit the reset switch on the front of the DVDplay The software will test your serial ports and try to locate the synchronizer If you get an error message check the cable or look at the chapter on troubleshooting for other suggestions 9 If it finds your synchronizer it will load the parameters that are currently programmed into it and it will display them in a window that will let you change them 10 Read the section of this manual called Parameters To Change in order to understand the various parameters Change them on this window to what you want 11 Once you have set all of the parameters the way you want hit the Save To Synchronizer button Until you do this the parameters have only changed on the screen not inside the synchronizer 12 If you want to change more channels on the synchronizer move the programming cable to the next channel otherwise skip over the next step and go to step number 14 13 Hit the reset switch on the front of the synchronizer and wait for the LED to change from red to orange This takes about 5 seconds
13. start playing their loop over again as soon as they are done without waiting for the rest of the channels There is a small delay between the end of the loop and the start of playing the loop again This delay is dependant on the search speed of the player and the disc used and whether you programmed it to start on a title chapter timecode or a frame number Searching on a title or chapter is faster than searching on a timecode or frame number but only by a second or two BEFORE USING THE DVDPLAY Before a DVDplay synchronizer can be used it must be programmed with the specific information for your discs and players This programming can be done for you by us using information that you supply or you can do it yourself using the supplied software and programming cable You can also reprogram it at any time yourself even if we did it for you the first time The synchronizer is programmed using an IBM style PC computer It does not have to be an IBM brand computer any compat ible PC computer will work The synchronizer comes with a 3 1 2 inch floppy disk or CD on special request that contains programs that are used to set parameters in the synchronizer Once it is programmed the synchronizer does not require an external computer to operate since it has it s own onboard computers that control the players A number of parameters must be programmed into the synchronizer for it to operate correctly These include the starting frame numbe
14. the disc e All channels go from red to out and they all stay out A switch or controller is shorting the Network connector e Each channel goes from out to green and plays normally but they don t all turn green at exactly the same time One or more channels do not have the Synchronize check mark checked in their programming PROBLEMS VISIBLE ON THE MONITOR e Problem The discs synchronize but while playing the video seems to be a sequence of still frames like step motion video Possible Cause There is a bug in the Pioneer players when a specific setting in the advanced setup menu is used It does not affect playback without the synchronizer but causes this symptom when any device controls the player via it s serial control port You can fix this by going into the Advanced Setup menu of the player and setting the REV STEP REV PLAY setting to VOBU e Problem Squelch is disabled to freeze the last frame of the video during rewind but the synchronizer starts in the wrong title the next time it loops Possible Cause The Pioneer player will slip a couple of frames when it reaches the end of a playback sequence When Squelch is disabled the synchronizer might slip past the end of the current title if the end point you program into the synchronizer is too close to the end of the title and there is more than one title on the disc When having Squelch disabled you must pick an end point that is at least 6 f
15. the factory default is 4800 It must match the settings in the synchronizer which are best left at their default of 9600 There are a few other settings that are important and some that are set based on how you use the synchro nizer We have listed all of the ones in the current version of the Advanced Setup Menu Pioneer sometimes changes these as firmware changes in the players The ones shown with an in front of them are important to set Others may be changed if you want to Please refer to the User Manual that came with the player for detailed information about each setting Parameter Suggested Comments page 1 Setting Weekly Timer OFF Turn this on if you want the players to automatically power themselves on and off at specific times each day 28 Parameter page 1 con t Power On Start Title Play Mode x Repeat Mode x BAUD Rate Tray Lock Blackboard Lock Stack Mode OSD x Rev Step Rev Play page 2 Player Control Panel Setup Lock mouse External Option SW Sync Out during SQ 29 Suggested Setting ON ALL OFF 9600 OFF OFF OFF VOBU Selectable ON Standard OFF Comments This brings the player out of standby auto matically when the power is applied Allows you to play all titles on the disc Important Important Not critical Not critical Not critical Important Not critical Not critical Not critical Important if disabling squelch in the sy
16. title Start Timecode Some DVD discs contain timecode This is not SMPTE timecode that may have been on your video while editing it This is a special DVD time code which defines the playback time on the disc in minutes and seconds If your disc has it and you specify Timecode as the Start Mode then you need to define the timecode that the playback loop will start at The DVDplay does not know what discs you will be using so it is possible to set this option and then use a disc without timecode If you do that the disc will not play You must be sure that your disc has timecode if you select timecode as your Start Mode The time is specified as an integer that is a combination of minutes and seconds This is Pioneer s special format The lowest two digits are the number of seconds The rest of the numbers are the number of minutes There is no hours as part of the number Hours are defined as so many minutes So for example the number 100 means 1 minute 0 seconds The number 12345 would mean 123 minutes 45 seconds which is 2 hours 3 minutes and 45 seconds You must be careful not to specify an illegal number For example the number 13579 is not valid because it specifies 79 seconds as the last two digits The last two digits must be within the range of 00 to 59 Start Frame When using Frame Number as your Start Mode you must define the starting frame number of the playback loop This mode
17. useful if you want to play up to the end a certain chapter or to play several chapters It is possible to create a dummy chapter at the end of a title containing a single frame and then use this to play to the end of the title However we suggest that you make that chapter be at least 5 seconds long If there is no chapter mark after the start point of the disc then you can not use a chapter as an ending point You can not set the same chapter number as both the start and the end point The ending chapter must be a chapter that is different and after the point where the synchronizer starts playing End Timecode Some DVD discs contain timecode If your disc has it and you specify Timecode as the End Mode then you need to define the timecode that the playback loop will end at The DVDplay does not know what discs you will be using so it is possible to set this option and then use a disc without timecode If you do that the disc will not play You must be sure that your disc has timecode if you select timecode as your End Mode See Start Timecode above for an explanation of the numbers that can be set for timecode End Frame When using Frame Number as your End Mode you must define the ending frame number of the playback loop This mode allows you the most precise control over where to end the loop Unlike starting the loop on a frame number ending the loop on a frame number has no effect on the pause at the end of the loop
18. B option which adds a black burst generator to the synchronizer then you have the choice of using it set for either NTSC or PAL video standards The setting must match the video standard of the discs you are playing If you did not order the B option then no special settings are required or available To change between NTSC and PAL black burst you must move a jumper on the black burst board which is inside To access the jumper you will need a small Philips head screwdriver and a small flat blade slotted screwdriver Be sure to unplug the power cable from the synchronizer before opening it Otherwise there are deadly voltages inside the box 36 CHAPTER 5 MISCELLANEOUS If you have the rackmount version then you simply have to remove the 4 screws on top of the box and remove the top cover If you have the non rackmount version then you must first remove the 2 screws holding the front panel on Then slowly pull the front panel out part way being careful not to pull too hard It has small wires connecting it to the boards inside so as you remove the front panel you will feel those wires as they tighten and prevent the front panel from going out any further from the box Put the front panel down on a table while holding the rest of the box an inch or so above the table and slide the top cover forward until it comes off Next locate the black burst board It is the smaller of the 2 circuit boards mounted to the bot
19. Dave Jones Design PFDs DVDplay User Manual Programming and installation instructions for using DVDplay synchronizers Dave Jones Design 34 Lake St Owego NY 13827 USA phone 607 687 5740 fax 607 687 5898 e mail contact djdesign com web www djdesign com DVDplayUser Manual Contents Introduction to DVDplay Synchronizers 0000008 L Overview of this Mantial wsc escesscccssesessceassncavized satdesseevteasveecsetereneees 1 Introduction to the DVDplay eee eee ceseeseceseeseceseeeeenseees 1 Syne VS Synchronization sa bc3s cele eesdsidee eeosbei diestiegsinus aided 2 A Typical SSO aeria eaea E AEREE R 3 HOW it WOPKS esemototikese toe eoon e REEE ERRE 4 Before Using the DVDplay cceceeesecssercesesseeetseeeceteeeeeeneens 5 Models ieee eeii eae e eee eee eee la keene 5 Optional EX tas scsi osjecas iEn E E E A E antes 6 PIAY CS eiea a E ATE E concen ERA ER AT E 6 DAS E SE EE T T E E 7 Electricity es i te edhccecea sks oeiee eia e E AEE EEE 7 SPECI MOGEIS mesdren n ae E EEEE 7 Connectors and Controls vss iesiesceschevecescehesevlsarteieia neces 8 Part NUM DEES eere rere Neee rE RERE REE E ETENE 11 DV Dplay Specifications isi ncaietiiein uitienn ens 12 SOLU WIE sosishsvessssadeaveciscnssadiassavsisvouesesateoassessensssasssertesaeesve LO IntrOGUCt Om DSA vecvescerseti T 13 Installing the SoftWare ecni eatoni orseson gisi eai 14 In Wind WS eneon ei hea tees reeds eee ween dee 14 Insta
20. any time and it will control a player connected to it but it will not be synchro nized to any other channel if the Synchronize parameter is not enabled FREEZING THE LAST FRAME DURING REWIND The synchronizer can be set to display either the player s background color while the discs are rewinding back to their start point or it can be set to freeze the last frame and hold it while the disc is rewinding Once the synchronizer reaches the start point the image will switch to the first frame until playback begins There are two things that must be programmed into the channel using the program ming software There is also a setting in the player that must be in the right setting 1 Turn off the squelch for that channel This is done by removing the check mark next to Squelch in the programming software In the DOS software you set Squelch to Disabled 2 Add 1 VD to the end of Init String 1 using the programming software 3 In the player s Advanced Setup Menu make sure that SYNC OUT DURING SQ is set to OFF To get to the Advanced Setup Menu on the Pioneer DVD V7300D or DVD V7400 hold down the Setup button on the remote control for a couple of seconds For the older DVD V7200 players you hold the Menu button on the remote for at least 3 seconds 34 EXTERNAL TRIGGERING If you ordered your DVDplay with the optional Network Connector you can use it as an external trigger to star
21. been sent to the DVDplay 15 If you are finished programming all of the channels that you plan to change you can skip steps 16 through 19 Disconnect the programming cable from the DVDplay and then hit the escape or ESC key on the keyboard If you can t find this key then hit the X key You can now turn off the computer and disconnect the other end of the programming cable 16 If you have more channels to program you should now move the programming cable to a different channel on the DVDplay 17 Hit the reset switch on the front of the DVDplay and wait for the lights to change from red to orange 25 18 About two seconds after the lights change from red to orange hit the L key on the keyboard and the program will read the current data from the new channel and display it on the screen If there is a problem reading the new channel you will see an error message If this happens try steps 17 and 18 again 19 Repeat steps 12 through 18 for each channel on the DVDplay that you want to program 26 Chapter 4 Installation INTRODUCTION Before the synchronizer can be used the Pioneer DVD players must have at least one setting changed on them You may also need to change some other settings in the players depending on the options you have in your synchronizer and how you plan to use it The BAUD rate of the player is the most important setting and is the cause of most problems with the players The factory setting f
22. d Green or Blue and use the left and right arrows to change the color A small box 27 on the right will preview the color you have mixed When you are happy with the color hit the Enter button to accept the change Once you are back to the General tab then hit the Setup button to store this new Setting in the player s memory Until you hit setup the new color is not stored in the player and would be lost after power down To get to the Advanced Setup Menu hold down the Setup button on the remote control for a couple of seconds Once the menu shows up then release the button The Advanced Setup Menu is a text menu not a graphical menu There are two pages of settings listed You use the up and down arrows to move between the parameters and also between the pages In most cases you use the Right arrow button to change the setting In some cases you are taken to another menu for additional information such as the Weekly Timer But most of the settings are multiple choice so you simply hit the right arrow several times to cycle through the choices As with the basic setup menu the changes you made are not saved until you hit the setup button again and exit the menu If you were to simply turn off the power while in this menu your changes would be forgotten The most important parameter to set is the BAUD rate If this is not set correctly the synchronizer can not control the player We strongly suggest that this be set to 9600 BAUD
23. e Drawer figure 3 DVDplay 3 back panel same as LasrPlay 3 Voltage Selector This is a rotary switch that can be changed by inserting a small screwdriver in the slot and turning The voltage selector chooses between 100 125 volts and 220 240 volts The voltage does not have to be precise the switch just selects the voltage range Power Inlet The power cord gets plugged in here The fuse is also inside this part The fuse can only be removed when the power cord is not plugged into the power inlet The fuse is inside a small drawer that can be opened with small screwdriver The fuse is a 5x20mm 0 315 amp slow blow type of fuse When running only on 220 240 volts this can be a 0 15 amp fuse The synchronizers have internal surge protectors that will cause this fuse to blow if the input voltage goes above 130 volts when set for 110 or above 260 volts when set for 220 The power cord is a standard international IEC type power cord Replacements are available at most computer stores around the world Power Switch gt Status LEDs Reset Switch figure 4 DVDplay 7 front panel same as LasrPlay 7 DVD Connectors Power Inlet Voltage Selector Fuse figure 5 DVDplay 7 back panel same as LasrPlay 7 Black Burst Out optional This is an optional video reference signal output that is fed to the ext sync input on certain Pioneer players to ensure that the video outputs are locked at the vertical interval
24. ecial purposes Start Mode You can start the playback loop on a specific Title Chapter Timecode if the disc has it or Frame Number Use the Start Mode to specify which of these you will use Your choices for Start Mode and End Mode may be limited by the way that your discs were authored In order to use frames the disc must allow searching by frames In order to use timecode the disc must contain the DVD time code This is not SMPTE timecode like you may have used when editing the video It is a special time code that is on some DVD discs It defines the current position on the disc in minutes and seconds It does not include hours of frames like SMPTE timecode Hours are simply counted in minutes so 123 minutes is the same as 2 hours and 3 minutes Start Title Since a DVD disc can contain several titles you need to specify which title to start playback in If you select Title for the Start Mode this is the only parameter required to define the start of the playback loop Otherwise you use this parameter to define which title the start of the loop is in and one of the following parameters to define the precise starting point 17 Start Chapter Each title on a DVD disc can contain several chapters If you select Chapter as the Start Mode you need to specify which chapter to start the playback loop at Most DVD authoring programs create a default chapter called Chapter 1 which is the start of the title frame 1 of the
25. hen Restart the computer in MS DOS mode Some customers have had problems programming on machines with specific Local Area Network cards If you experience this see the special note in the troubleshooting chapter at the end of this manual 3 If your DVDplay is in a rackmount box make sure that the power switch on the front is off Plug the power cord into the back of the DVDplay and plug it into the wall 4 Connect the DVDplay programming cable to the DVDplay channel to be programmed each channel must be programmed sepa rately For multi channel synchronizers you should just start with the first channel and repeat this process for all channels 5 If you installed the software on your computer change to the drive it is installed on by entering the drive letter followed by a colon and then hit Enter If you didn t install the software on your computer put the disk into the floppy and type in A or B if that is your floppy and hit enter 6 Now change to the directory the software is in by typing CD DVDCUST and hitting Enter 7 If your DVDplay is a rackmount version push the power switch Smaller DVDplays will already be on at this point 8 Enter DVDCUST followed by a space and the number of the serial port for example DVDCUST 1 for COM1 or DVDCUST 2 for COM2 Do not hit the Enter key yet 9 Hit the reset switch on the front of the DVDplay Wait for the lights on the front of the DVDplay to change from red to orange
26. lack burst will work but it is often easier and cheaper to have this built into the same box as the DVDplay The synchronizers can also be made with an option known as a network connector which is used to tie together two or more synchronizers to make them act like one large synchronizer Even though this is called a network connector it is not a standard computer network It is an extension of the proprietary internal network that channels use to synchronize with each other It can also be used to keep the channels from starting a playback loop By connecting this to a switch or contact closure that shorts the pins together you tell the synchronizer to not start Once the switch is pushed or contacts opened playback starts PLAYERS The DVDplay is compatible only with Pioneer industrial DVD players The DVDplay supports Pioneer s DVD V7200 7300 and 7400 The 7200 was the original model which was discontinued in January 2000 The 7300 is sold in regions that use PAL and 220 240 volts AC such as Europe while the 7400 is sold in regions that use NTSC and 100 120 volts AC such as North America DISCS The DVDplay is designed to work with DVD Video discs whether they are mass produced or DVD R custom recordings It is not designed to work with Video CD which the industrial players will also play Video CD is an old non DVD format used primarily in Japan with MPEG 1 DVD Video is the DVD format that uses MPEG 2 They a
27. lay a still frame of the first frame of the loop until all channels are ready to start Do not turn this off if you are ending your loop on a Title number When turning off squelch and using a remote start button add 1 VD to the end of the first init string Init Strings The four init strings hold all of the initialization com mands for the DVD player These commands are sent from the DVDplay to the player during start up These are pre programmed with the most common initialization commands and most people never have to change them There are a number of commands available here but you should only change them if you understand Pioneer s command language Sending an invalid command will cause other commands after it to be ignored The commands each consist of a number followed by letters The various commands are strung together into strings of 3 or 4 commands Be careful when you change these strings because if you eliminate one of the default strings your player will revert back to it s own default settings which may not be what you want 20 The default init string in a DVDplay is init string 1 OKLODS The init string shown above contains 2 commands that set the DVD player to enable the front panel OKL and don t display title chapter timecode or frame numbers on top of the video ODS Some of the more common options are OKL player s front panel enabled 1KL player s front panel disabled locked out ODS d
28. lem could be the cause If so running the DOS software will probably solve the issue It is also possible that you forgot to hit the Reset button on the front of the synchronizer before trying to load from the synchronizer It is important to always hit the Reset button and wait for the lights to change from Red to Orange before hitting the Load From Synchronizer button We have also found that some people hit the button a bit too fast Try waiting a couple of seconds after the lights turn Orange before hitting the Load From Synchronizer button 40 Another possibility is that the serial port you selected is not actually the correct one or is dissabled Sometimes the software will be fooled by something else in the system that responds as the serial port and the software will think it has found a synchro nizer But when it tries to load or save data between the computer and the synchronizer it is not able to do so Be sure that the serial port you selected is the correct one If this problem happens when trying to save data to the synchronizer it is possible that you didn t first load the data that was in the synchronizer into the program You must always load from the synchronizer then modify the data then save it back to the synchronizer You can not simply move the cable and hit Save to Synchronizer to try and save the same settings to more than one channel The correct sequence is 1 Hit the Reset button 2 Wait for the lights
29. like Can t save to synchronizer or Bad data in synchronizer or Can t find synchronizer when trying to load or save data between the computer and the synchronizer Possible Cause If it happens when trying to load from the synchronizer using the L key it is probably because you did not hit the Reset button on the synchronizer and wait for the lights to change to Orange You should also wait 2 seconds after the lights change to Orange before hitting the L key If it happens when trying to save data to the synchronizer using the S key then it is possible that you did not first load the data from that channel You can not simply move the cable to anew channel and hit the S key to save the same data to several channels You must first load the data from the synchro nizer into the software then edit it then save it back to the synchronizer PROBLEMS WHILE USING THE SYNCHRONIZER Most problems when using the synchronizer can be figured out with the help of the colored lights on the front of the synchronizer Each channel has a colored light that has four possible states The basic meaning of these colors is RED Initializing after power up or after an error ORANGE No player such as when computer is connected OUT When channel is ready to start or rewinding GREEN Channel is playing By watching the sequence of these colors you can tell a lot about what the channel is doing For example
30. lling on the Desktop e cc eeeeeseeceneeeneeeeeeeeeeeeeneeeees 14 Pull Tins ta ati ths ecss ccecs cesetzsecesseeia sivas cxscseasesessstuzecxereeeees 15 ig BO Senees ee etre peer eer treerer E etree reer reece tre tree 15 WO AUCTION sissiscssessstscepeesis seep tab hivae bbsuchsastsonatecesevyassnsnertonsousnatey 17 Parameters to CRAan Ge 2 siesccceeseve cblavtve svsdacsesuscescesvevoanuocansotneees 17 Programming the DV Dplay ecceecceesceeeneeseeceeeeceteecsaeeeneeenees 21 Programming under Windows ecceeeseeereeeseceeeeceeeeeneeeenees 22 Programming under DOSis tor sorsrorei cireni 23 ii Tinstallationiscccccccccsssssccisccscccssissascsscieccccstesscecscssocdsssesacesssesa DT WintHO GUC TONE eiia TE E EER E Ge 27 Installing the ID VD play cssccic cesteciavtastesceesbissensincs A 30 Miscellaneous ss ciaccessasensccesnccndecasnctiecinisvessiantasetananesetauante JJ IMOMUCHON ssis EE E 33 Disabling a Channel essrcorniisisersrccurrpe tetesi tere ss serseri rssi 33 Using the Windows Software eeeeseeeeeeeeeseeeerrrrererreerrreen 33 Using the DOS Software 3 c ci isessescscestsssnesstaespsets cat tetsctassens 33 Freezing the Last Frame During Rewind eee eee eres 34 Extetmall Triggering ssa scsescdivsiesestesdsiatcssesbesasssvassssvscaseeeanesbipceseacty 35 Changing the Background Color cee eeeeeeceeseeeeeeeeeeeeeenes 35 Changing Between NTSC and PAL oe eee eee eeeeeeereeeeeeees 36 Troubleshooting
31. lso do not work with DVD RAM or other computer formats ELECTRICITY The DVDplay runs off of 100 125 or 220 240 volts which is switchable on the back with a small screwdriver All of our synchro nizers are supplied with a detachable American standard power cable for 110 volt use They use the standard international IEC power connector on the back of each unit so a local power cable can be purchased in almost any country in the world These are the same power cables used by most computers and many other electronic devices SPECIFIC MODELS There are a lot of different models of DVDplay synchronizer 1 2 and 3 channel synchronizers come in small boxes that are about twice as thick as an external modem The larger models come in rackmount boxes that fit in standard 19 inch equipment racks though they can have the rack mounting brackets removed if you simply want them in a box to place on top of other machines Synchronizers with 4 through 7 channels come in 1RU one rack unit boxes which are 1 3 4 inches tall Synchronizers with more channels come in taller rackmount boxes The smaller synchronizers can also be ordered in rackmount boxes for an additional cost The 1 2 and 3 channel models don t have a power switch because they use a fraction of a watt of power and in most installations they are plugged into a power strip along with the players so all devices get turned on and off from the strip When you plug them in the ligh
32. n probably use the DOS softwae For Windows 98 you need to restart the computer in MS DOS mode For Windows ME NT 2000 and XP you can open a Command Prompt Start gt Programs gt Acces sories gt Command Prompt and run the DOS software in that The DOS software can set all of the same parameters it just uses a simpler text based interface 1 Connect the DVDplay programming cable to a serial port on an IBM style PC computer PC type computers have serial ports with either 9 pin connectors or 25 pin connectors on some old ones Most newer ones just have 9 pins The DVDplay programming cable has a 9 pin serial connector If your computer is an old model with a 25 pin serial port you will need to get a 25 pin to 9 pin serial adapter They are available at most computer and electronic parts stores 2 Turn on the computer and let Windows boot 3 Plug the power cord into the back of the DVDplay and plug it into the wall If it is a rackmount version turn on the power switch 4 Connect the DVDplay programming cable to the DVDplay channel to be programmed each channel must be programmed sepa rately For multi channel synchronizers you should just start with the first channel and repeat this process for all channels 5 If you installed your software on your desktop double click it now If you did a full installation click the Start button then Programs Dave Jones Design and select DVDsync If you didn t install the software
33. nchro nizer to freeze the last frame of video during rewind Parameter Suggested Comments page 2 con t Setting x External Sync OFF Important Set this off if you are not using black burst NTSC Set this to NTSC if using NTSC black burst and discs PAL Set this to PAL if using PAL black burst and discs x AV Sync Compensate OFF Important INSTALLING THE DVDPLAY 1 Follow the instructions in the previous section to set up the players 2 Plug the power cord into the back of the DVDplay and plug it into the wall or the power strip used by the Pioneer DVD player s that you are using If you are using one of the smaller DVDplays that doesn t have a power switch you can leave the DVDplay plugged in and turned on all the time it uses ten times less power than a night light 3 Connect the 15 pin cables from each channel of the DVDplay to each of the DVD players 4 Connect all of the video and audio cables to the DVD players 5 If your DVDplay has the optional black burst reference out connect it to the Ext Sync input of the first DVD player Now connect another cable from the sync loopthru output of that player to the ext 30 sync input of the next player Continue to chain all of the DVD players together this same way Make sure that the termination switch on all of the players except the last one in the chain are set to HI Z The last one in the chain should be set to 75 ohms 6 If you are connecting
34. neers like them because they are so easy to program and install and curators like them because all they have to do is turn the power on in the morning and the exhibition starts automatically The DVDplay uses the same hardware design as the LasrPlay but has new firmware for controlling Pioneer s industrial DVD players SYNC VS SYNCHRONIZATION Let s take a moment here to understand that there are two different types of synchronization happening in some DVDplay systems and it is important to understand the difference The DVDplay is a synchronizer in the sense that they play sections of several discs so that a specific frame of video on one disc starts playing at the same time as a specific frame of video on another disc or several other discs This is something you can see visually on several monitors playing those channels of video The other type of synchronization is invisible to the naked eye and requires test equipment to see it though it can affect the accuracy of the first type If you understand how video works you know that the image is scanned onto the monitor starting at the top left corner of the screen and scans across to the right side over and over again each time a little lower on the screen The part of the video signal that tells the monitor to start scanning at the top of the screen is known as vertical sync The part of the video signal that tells the monitor to start scanning each scan line on the left side
35. of the screen is known as horizontal sync There are a lot of horizontal sync pulses one per scan line for every vertical sync pulse Certain video devices can be fed an external sync signal to force their video signals to start vertically and sometimes horizontally at the same time You can t see this with your eyes but if the video signals go 2 into a switcher it may require this type of synchronization Pioneer s industrial DVD players accept a black burst signal to force it s video output to start scanning in sync with other players that also have this signal going into them Black burst carries vertical and horizontal sync information to the player and allows the player to put out video that is synchronized to the vertical and horizontal sync of the black burst Black burst also carries color reference information but the Pioneer players do not accurately lock to this information The DVDplay is available with an optional black burst output By feeding this signal to the players you are locking the internal electronics of the players so that the video outputs scan at the same time and the players internal computers are communicating with external devices at the same time By using this option you are increasing the accuracy of communication and therefore the accuracy of the start of the playback loops on the players Without this option the playback will still appear to start at exactly the same time but in realit
36. on t display text overrides RA 1DS display text see RA IRA display frame numbers must be used with 1DS 2RA display title and chapter numbers use with 1DS Other ones include settings for selecting subtitles audio tracks multilingual aspect ratio and camera angle Comment This is an optional text string and can be anything you want It is usually used to remind you of what this DVDplay was programmed to do such as the name of an installation or performance or the channel number of a multichannel display PROGRAMMING THE DVDPLAY You only need to program the DVDplay if it was not done for you when you ordered it or if you want to adjust some of the param eters If you have problems with the software be sure to check the support page of our web site www djdesign com for updated soft ware The DVDplay comes with programs for MS DOS and for Windows Most newer PC s are running Windows while most older PC s are running DOS or Windows 3 If your machine is using Win dows 3 then you must exit Windows and use the DOS program Do not shell to DOS from Windows 3 or 98 as this will not let the software find your serial port Be very careful in choosing the modes and other parameters that you program into the DVDplay If you use modes or parameters that don t match your DVD disc that channel will fail to work 21 Programming under Windows If you have any problems with the Windows based software you ca
37. or the BAUD rate is 4800 BAUD While the synchronizer can be programmed to match this it reduces the accuracy of synchronization We strongly recommend that both the player and the synchronizer are set to 9600 BAUD This is the fastest setting that the player supports and allows for the synchronizer to be frame accurate when used with black burst There are two setup menus in the players The basic setup menu is used for setting the background color the type of audio used and other typical user settings The advanced setup menu is for more technical settings and is the one where most of what we need to set is located It is best to turn off or unplug the synchronizer and to stop your discs from playing before trying to change the setup in the player Some discs will prevent these settings from changing if the disc is playing To get to the basic setup menu simply hit the button on the remote control labelled Setup Do not hold the button down Simply press it and release it The basic menu is a graphical menu with tabs across the top The only one we need to set is in the General tab Use the right arrow on the remote to move the highlight from tab to tab until the General tab is shown Then use the down arrow to go down to the Background Color Then hit the right arrow to move over to the box on the right and finally hit the Enter button to bring up the Background Color screen Now use the up and down arrows to select Re
38. ou should now be at a DOS prompt like C WINDOWS gt 2 Insert the floppy disk containing your DVDplay programming software into your floppy drive 3 If you only have one hard drive your prompt should now start with C If you have more than one hard drive change to the hard drive you wish to install the software on by typing in D or any other drive letter you wish to install the software onto and hitting the Enter key Your prompt should now have changed to the appropriate drive letter 15 4 To create a sub directory to hold your software type in MD DVDCUST and hit the Enter key 5 Type in COPY A DVDCUST DVDCUST EXE DVDCUST and hit the Enter key use B if your floppy drive is B Your software is now installed 16 Chapter 3 Programming INTRODUCTION The DVDplay synchronizer must be programmed to match the content of the DVD discs that you plan to use with it By default when synchronizers are first shipped they are pre programmed to start each channel at Title 1 and Chapter 1 of each disc and to play until they reach Chapter 2 If you do not have a Chapter 2 on the discs or wish to start and end at other points on the discs then the synchronizer will need to be reprogrammed with the parameters that meet your needs PARAMETERS TO CHANGE There are a number of parameters that can be programmed into a DVDplay Some of them are required for the DVDplay to work while others are options that are used for sp
39. r Installing on the Desktop 1 Insert the floppy disc containing the programming software into your floppy drive 2 Double click on My Computer 3 Double click on 3 1 2 Floppy 4 Double click on the DVDsynce folder 5 Drag the icon for DVDsync exe over to your desktop 6 It is now ready to use by simply double clicking the icon on the desktop 14 Full Installation 1 Insert the floppy disk containing the programming software into your floppy drive 2 Shut down all open programs and if you have a virus protection program disable it 3 Click on the taskbar s Start button then click Run 4 In the window that opens click in the text box and type in A Setup exe or B Setup exe if B is your floppy 5 Click OK 6 Follow the on screen instructions that the installer gives you It gives you several options but most people should simply keep clicking the Next button until it is done In DOS or problems with the Windows version 1 If you are running Windows3 x and you are simply installing the software now you can run a DOS shell to do this If you are planning on also using the software now then you must actually close Windows first not run a DOS shell To run a dos shell to install the software double click on the MS DOS icon To actually close Windows you must double click in the box in the upper left corner of Program Manager When it says that this will end your Windows session click YES or OK Y
40. r the ending frame number and the speed of the serial port in the player Several optional modes and settings can also be pro grammed into the synchronizer These include locking out the front panel controls to prevent tampering with the system as well as other options Refer to the programming chapter for step by step instructions on programming MODELS There are many models in the LasrPlay and DVDplay series but it is easy to remember the different model names Just add the number of channels after the name This means for example that the DVDplay 2 is a 2 channel DVD synchronizer while the LasrPlay 2 is the same thing for laserdisc players There is no limit to the number of 5 channels that can be built into a LasrPlay or DVDplay unit because every channel has it s own computer so a DVDplay 25 would have 25 channels In addition to the number there may be letters at the end of the model number to define options that were ordered See the table at the end of this chapter for exact model numbers OPTIONAL EXTRAS There are a couple of optional features that can be built into a synchronizer Most installations do not require these options As mentioned earlier the DVDplays can be made with an optional Black Burst output This option allows more accurate synchronization as well as locking the images to the vertical interval which is useful when the images are going into a video switcher Any standard sync generator that puts out b
41. rames before the end of the title We suggest it be even further away from the end of the title You also can not use a title as the ending mark when you have Squelch disabled You must end on a chapter time or frame 44 e Problem You have black burst going to all the players and the players going to a video switcher but the video from the players does not seem to be locked to each other Possible Cause The Pioneer players only lock to the external black burst when they go into play mode After that they will not attempt to lock to the black burst It is important that the black burst generator be powered up at the same time as the players or at least before the players start playing their discs Also even when the Pioneer players are locked to the black burst there is no guarantee that the color portion of their sync is locked together Pioneer does not guarantee this It only guarnatees locking at the vertical and horizontal intervals If you need to feed color video into a switcher such as an SEG you may need to timebase correct the outputs of the players NOTES Model Serial Number Settings 45
42. rom Dave Jones Design This series of devices is very similar to our LasrPlay series with a few differences Most of what is in this manual holds true for both the LasrPlay series and the DVDplay series except that the DVDplay series works with Pioneer s industrial DVD players and the LasrPlay series works with Pioneer s industrial laserdisc players Contact Dave Jones Design for specific information about the LasrPlay series The DVDplay synchronizers are intelligent programmable controllers for use with Pioneer brand industrial DVD players Their function is to play a section of a disc or multiple discs in a continuous loop In systems with multiple channels of video each channel can be programmed to start playing at the same time as the rest of the chan nels or be set to play in a loop by itself This synchronization of 1 multiple images is extremely accurate and can be used to make several channels of video look like parts of a single larger image These are not general purpose controllers that work with a computer to script a complex show Their sole purpose is to play a single loop over and over again with the channels synchronized to each other The LasrPlay and later the DVDplay synchronizers were developed for use in optical disc based video art exhibitions and they are installed in museums around the world Their ease of use and high reliability have been praised by many artists curators and installers Artists and engi
43. ry to help identify the most common of these though there is no way we can identify all possible sources of trouble here ERRORS WHILE PROGRAMMING When having problems using the software to program a synchronizer be sure to go to our web site www djdesign com and check our support page for updated versions of the software Errors with the Windows Software e Problem The software does not find the synchronizer Possible Cause The serial port you selected may not be the correct one or may not be enabled Just because you have a serial port connec tor on the computer does not mean that it is enabled or that it is COM1 Many laptops and some desktops are set up with the serial port connector disabled because the serial port is being used for something else The serial port might be configured in the BIOS to be an Infra Red port or an internal modem or some other device You may need to get into the computer s BIOS to check this Many desktop computers have two serial ports Try the second one If you have Palm Sync software installed for use with the Palm Pilot it is possible that it has taken over the serial port and will not allow other software to use it Try disabling the Palm Sync software and try the synchronizer again A third possibility is that you forgot to hit the Reset button on the front of the synchronizer after telling the software to find the synchronizer It is important that you hit the reset button as 39
44. s 5 small fast computers in it to control the 5 players Because each computer only has to control a single player and all of the computers talk to each other over an internal network the control and synchronization is very fast and accurate On power up the synchronizer channel will take control of the player through it s serial port and if there is a disc inside it will spin up to speed Once the disc is up to speed the synchronizer will seek out the starting frame number of the loop to play When the starting frame has been reached it waits at that frame while the channel checks an internal network to see if every other channel is ready to play If not the channel waits for the rest of the channels to get ready Once all synchronizer channels have reached their starting frames they all start playing at the same time When the playback loop is started all channels start at exactly the same time Once they start they will stay synchronized for the duration of the playback When each disc reaches their ending frame number of the loop the picture and sound are blanked out and they once again seek out the starting frame number and re synchronize for the next playback loop If the channels are programmed to play different length segments on each disc each player will go blank at the end of their particular loop and then wait for the rest of the players to finish If any of the channels have been programmed not to synchro nize they will
45. sssssisssssssssssistsssscssssscssesssscsssssssassssvsssessess OF WO GUC HON esee ricorse oeae or ERE PEKEE E NEE ATE EEEE 39 Errors while Programming sssini eesis 39 Errors with the Windows Software ccceeeeeseeeeeeeeeeees 39 Errors with the DOS Software 0 0 seseeseeseeseesseeneeseeens 41 Problems while Using the Synchronizer 0 eee eee 42 Symptoms Based on the Channel LEDs eee 43 Problems Visible on the Monitor eeeeeeseeeeeseeeeeeeeeeeees 44 iii Chapter 1 Introduction to DVDplay Synchronizers OVERVIEW OF THIS MANUAL Whether you have used the DVDplay synchronizers before or not we suggest that you at least read this overview before jumping into the other chapters It is important that you follow the step by step instructions in the programming and installation chapters Skipping steps such as hitting the reset button at the correct time will cause problems with the programming If this is the first time that you have used a DVDplay we suggest that you read this entire manual first The steps involved in using the DVDplay synchronizer typically include 1 Analyzing your discs optional if you understand the way they were made 2 Programming the Synchronizer to match the discs 3 Setting parameters in the player s setup menus 4 Connecting the synchronizer and players 5 Debug any problems INTRODUCTION TO THE DVDPLAY This chapter describes in detail the DVDplay series of synchronizers f
46. t your synchronizer s playback loop To do this you will need a special switch or a controller with a programmable set of contact closures The Network Connector is an RCA also called a Phono connector When it s center pin is connected to it s outer shell the synchronizer will not start playing it s playback loop Once the connec tion is opened playback starts To do it with a switch you need a push button switch with normally closed contacts This means that the switch s contacts are connected together until you push it The more common type is the normally open type so be sure that you get a normally closed type or a Single pole double throw switch that has both normally open and normally closed contacts Simply connect the common and normally closed contacts of the switch to the center and outside of an RCA plug and plug it into the Network Connector When you push the button the contacts are opened and playback starts CHANGING THE BACKGROUND COLOR When the synchronizer finishes playing the content of your discs it rewinds back to the start of your content re synchronizes and then starts playing again During that rewind time if you have Squelch enabled in the synchronizer the output of the players will switch to the player s background color You can change this back ground color to any color you want By default the Pioneers ship with the background color set to Blue
47. th this type of installation the program is simply sitting on your desktop and you run it by double clicking the icon there That type of installation is called Installing on the desktop below The other type of install called the Full Install or Full Installation will install the program for you in the Program Files folder of your hard drive and will create shortcuts for you like most other Windows programs You can then run the program from your Start gt Programs list like most other Windows programs This type of 13 install uses the standard Windows InstallShield installer which leads you through the installation process If you just need to program the synchronizer once and don t plan to use this same computer in the future to program synchronizers again we suggest that you do the simpler install and just install the program on the desktop Or an even simpler method is to simply run the software directly from the floppy disk The DOS version of the software does not have an installer You are simply copying the program to your hard drive and using it from there INSTALLING THE SOFTWARE There are programs to run under MS DOS or Windows If you are using Windows3 x follow the instructions for MS DOS In Windows You can either install the software directly onto your desktop or do a full installation which creates an entry in your Start menu and installs an uninstaller to remove the software late
48. the normal sequence of 42 colors after hitting the Reset button is 1 Red initializing 2 Out ready to start 3 Green playing Then each time the loop plays after that the lights will go out rewinding and ready then green playing This repeats over and over If any of the channels do not follow this sequence of colors then there is probably some kind of problem Use the following to try and find the source of the problem Symptoms Based on the Channel LEDs e No lights on synchronizer gt Fuse is blown Bad power cable Power switch off rack versions only A channel light goes from red to orange and stays orange Channel not connected to player Player turned off e A channel light stays red on the synchronizer lights don t change on player Player BAUD rate not set to 9600 A channel light stays red on synchronizer Keylock light blinks on player gt DVD Disc is wrong format Synchronizer Start point does not exist on the DVD disc e A channel light goes from red to out to red again and repeats Start point or End point of synchronizer does not exist on the DVD disc e A channel light goes from red to out then blinks green and then back to red gt End point of synchronizer does not exist on the DVD disc 43 A channel light goes from red to out to green then goes out fairly quickly The difference between the Start and End points is very short on
49. to turn orange 3 Wait another 2 seconds 4 Load the data from the synchronizer 5 Edit the data in the software 6 Save the data to the synchronizer e Problem After programming the synchronizer you check the pro gramming and the settings you thought you edited did not get saved to the synchronizer Possible Cause You probably did not remember to save the data to the synchronizer While you are editing the data on the screen of the computer that data is just in the computer The synchronizer is not updated until you click the Save To Synchronizer button on the software Errors with the DOS Software e Problem You get an error that says something like Can t Find a Synchronizer when you first run the software Possible Cause The DOS software does a simple test for the programming cable and then tries to read the synchronizer It is possible for it to be fooled by a network card or other device that is using the 4 serial port Be sure that you have specified the correct serial port when you run the software This can also happen if you do not hit the Reset button on the synchronizer and wait for the lights to change from Red to Orange You should do this just before starting the software It is also a good idea to wait about 2 seconds after the lights change before starting the software If it still doesn t work you may need to try a different computer preferably a desktop e Problem You get an error
50. tom plate It has a long blue connector on the side which has 5 terminals The middle one is labeled NTSC and the one on the end says PAL The one between them has the electrical symbol for ground a vertical line above three smaller lines To set the black burst board for NTSC there is a small jumper wire going between the ground terminal and the NTSC terminal To set it for PAL video you move the jumper so it connects the ground terminal with the PAL terminal Black Burst board set to PAL 37 After changing the jumper simply reassemble the case For the rackmount version simply place the top cover back on make sure that the screw holes have their tapered side facing up and replace the screws For the small case you must first pick up the main part of the case and slide the cover on from the front The edges of the cover slide inside grooves in the base plate Be sure that the edges of the cover slide into these grooves otherwise the cover will be loose Then carefully place the front cover back on and screw it in place using the 2 screws you removed when taking it apart Black Burst board set to NTSC 38 Chapter 6 Troubleshooting INTRODUCTION There are many possible causes of problems in a synchronizer system There can be problems programming the synchronizer prob lems caused by the way the discs were authored and problems with the way the rest of the hardware is set up or connected We t
51. ts on the front will start by glowing red so you know they are working The rackmount versions have a power switch mounted on the front so they can easily be turned off power cables in equipment racks are traditionally hard to get to 7 The other controls and options are the same between the smaller units and the rackmount units except that the small units have the player connectors on the front while the rackmount models have them on the back CONNECTORS AND CONTROLS Power Switch only on rackmount units To turn the synchronizer on and off This lights up when the unit is on Reset Switch Pressing this momentary push button switch will reset the synchronizer All channels will pause for about 4 seconds and then start up as if power had just been turned on Status LEDs The multi colored status lights provide some feedback to the user as to what the synchronizer is doing GREEN playing RED initializing ORANGE programming or not connected OFF synchronizing or waiting to start the loop Player Connectors The 15 pin D shell connectors are connected to the programming cable during programming and are connected to the Pioneer players during normal operation This is the serial control signal that tells the player what to do Status LEDs DVD connectors s Reset Switch figure 2 DVDplay 3 front panel same as LasrPlay 3 Voltage Selector Power Inlat j J j Syne or B B Network Fus
52. y 3NR 3 channel in rackmount box DVDplay 3BN ue 3 channel with black burst DVDplay 6BN 6 channel with black burst DVDplay 32BN 32 channel with black burst Note These products are currently only available directly from Dave Jones Design 11 DVDPLAY SPECIFICATIONS Power Supply Voltage wee F ge eonun aaun oraa DYD Format sid seeesdscohasceaas sessevtavecas ene Compatible Players sisenes Connectors PO WEI iaaeaie DVD NetWork scenaron Controls oannaam a E S Speeds Times approximate PowerUp srren Disc spin up Synchronization ROWING eca Accessories Supplied cece Options Available eee eee 100 125 or 200 250 volts 50 60 Hz 5x20 mm 0 315 amp DVD Video Pioneer DVD V7200 discontinued Pioneer DVD V7300 Pioneer DVD V7400 IEC international plug DB 15 male RCA gold Reset switch Power On Off only on rackmount versions 7 seconds 5 10 seconds 0 5 second 2 10 seconds IEC power cable with USA connector 15 pin DVD cables 6 feet long one per channel Programming software for PC only Programming cable Rack mounting brackets only with rackmount models User manual Blackburst output Rack Mount Case optional on 2 and 3 channel units Standard on 4 channels and above specifications subject to change without notice 12 Chapter 2 Software INTRODUCTION The DVDplay must be programmed at least once
53. y it may be off by as much as 2 frames of video Most video installations don t require using these options because it is visually hard to detect a frame of video but the most exacting installations should probably have this option A TYPICAL SYSTEM A typical system consists of a multichannel synchronizer hooked up to a number of Pioneer industrial players though there MR DVDplay is a one channel version available wa for times when Pioneer you only need to l a DWD Playe rS players will be connected to a video monitor or play a loop ona projector Some figure 1 a ai system single player E 3 Each of the Monitors or all of the players might also be connected to audio amplifiers and speakers There is no central computer required in this system because the synchronizer has it s own computers to control the players The cables needed to connect the synchronizer to the players are included with the synchronizer HOW IT WORKS The synchronizer must be programmed at least once prior to use either at the factory or by the user This can be done with any IBM style PC computer it doesn t have to be an IBM brand using the software and cable supplied with the synchronizer Once programmed it no longer needs any external computers to control it Each channel of the DVDplay synchronizer has it s own high speed RISC computer that communicates with a single player This means that for example a 5 channel device ha
Download Pdf Manuals
Related Search