view user guide
Contents
1. 11 il Hardware Installation 3 2 Installation Flowchart 2 Remove Back Chassis Cover 3 Mount Hard Disk Drive 4 Mount Mainboard 5 Install CPU CPU Fan Memory Module it Note Please refer to the installation procedure in the user s manual provided by the mainboard vendor 6 Connect Mainboard Audio Cables to activate Line out Mic in jack on the rear of the system 7 Connect Other Cables Optical Drive Audio HDD USB Reset HDD LED Power LED Power On ot Note Please refer to the installation procedure in the user s manual provided by the mainboard vendor 8 Install Riser Cards option 9 Connect VGA amp Touch Panel Optional Cables 10 Check If All Parts Are Properly Connected 11 Replace Back Chassis Cover 12 Finish _12 Iil Hardware Installation 3 3 Installation Procedures 3 3 1 Remove Back Chassis Cover 1 Place the sponge on the platform to protect the LCD panel Then place the system barebone face down the sponge 2 Remove the screws 8 pcs to open the back cover 3 Remove the back cover _ 3 il Hardware Installation 3 3 2 Mount the Hard Disk Drive Screw type Mounting screws provided by the Hard Disk Drive vendor 1 Discharge the HDD mounting plate from the system plate Firmly screw the Hard Drive onto the HDD mounting plate 2 Firmly screw the set of HDD and mounting plate2. x Il Product Overview ot Note Please refer to Chapter IV LCD Panel Monitor for more information of functional control 3 Multi in One Card Reader This card reader is multi in one type includes 1x USB port 1x Compact Flash 1x Memory Stick 1x Smart Media and 1x Secure Digital slots It supports USB Revision 2 0 Compact Flash Il IBM Micro drive Smart media Secure Digital Mini SD Multi Media Card RS MMC Memory Stick MS Pro MS Duo MS Pro Duo MS magic Gate excellent Digital The card reader is automatic card detection It supports hot swapping between cards and copying among different media or cards 2 4 Left Side View 1 Optical Device Bay 1 Optical Device Bay This is where the CD ROM DVD ROM CD R RW CD R RW DVD Combo DVD R RW DVD combo drive was fixed to The optical drive optional CD ROM DVD ROM CD R RW CD R RW DVD Combo DVD R RW DVD combo is a slim internal type weight 235 5 g for steel or 190 5g aluminum top case designed by internal drawer type manual load structure with 12 7 mm height The IDE ATAPI interface enables to access various CD DVD formats widely It supports multi operating systems II Product Overview 2 5 Bottom View _ i PFPP ra PP le le eA eat Pe eee y Ta a a a a a A WITTE T T ECEE EEE Bey CAERE A O PAD 3 Power Socket 2 Fan Grill 1 Voltage Switch 4 Mainboard I O Ports 5 Extension Brackets 1 Voltage Switch
3. Cables Connect the other cables on the system plate to the mainboard including Optical Drive Audio HDD USB Reset HDD LED Power LED and Power On The following picture contains all the cables that built on the system plate including the mainboard s audio cable mentioned on 3 3 4 i i qep jqep opny enug jeondo aIg2D MS 19804y 9925 MS J8Mog ST 2198 031 00H aged gsn aigeD gsn ajqeo olpny pJeoquiey ee BE 21989 G37 mog Caution Make sure the power cable is not connected to AC outlets until after installation is completed co Note To connect the system cables correspond to those on the mainboard please refer to the installation procedure in the user s manual provided by the mainboard vendor _16 il Hardware Installation 3 3 5 Install the Riser Cards Option Screw type Round headed mounting screws for riser card The riser cards AGP riser card PCI Express riser card PCI riser card allow you to plug the VGA graphic card PCI Express graphic card and PCI cards into the mainbaord of the system Caution aN adding or removing extension cards make sure to turn off the power first Note Please refer to the user s manual provided by the extension card vendor to make any necessary hardware or software settings VGA Graphic Card Installation 1 Insert AGP riser card to the AGP slot on the mainboard 2 Remove the slot cover from the system case in the space where
4. are provided for ventilation to ensure reliable operation of the system and to protect it from overheating These openings must not be blocked or covered Do not lean the system direct to the wall Keep some spaces min 5 cm between the wall and system product Do not push any object into the slot in the system product cabinet It could touch dangerous voltage points or short out parts resulting in a fire or electric shock Keep the system and power supply away from direct sunlight or any source of heat Do not subject the system to the temperature below 0 C 32 F or above 40 C 104 F Do not place the system product near or over a radiator or heat register Keep the system product away from the magnetic interference such as high capacity transformers electric motors television and other strong magnetic objects Do not place the computer on the top of the other electronic devices To protect the system product during a lightening storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet This will prevent damage to the system product due to lightning and power line surges Important Safeguard 19 Unplug the power cord before inserting any add on card or module 20 Use power cord correctly There are some important safety requirements The power cord is equipped either a 2 prong or a 3 prong grounded plug The third prong is an important safety feature do not defeat the safety
5. back to the system plate 3 3 3 Mount the Mainboard Screw type Round headed mounting screws for mainboard Standoffs 1 Insert the standoffs into the appropriate screw holes on the system plate 2 Insert the I O shield plate _14 IiI Hardware Installation 3 Place the mainboard on the system plate aligning the mainboard mounting holes over the standoffs Make sure the mainboard s I O connectors are aligned with the correct slots on the I O shield plate of the system plate Insert the mounting screws through the mainboard mounting holes into the standoffs and firmly screw secure Caution Check to ensure that the underside of the mainboard is not touching the system plate in any place If there is any contact the mainboard may short causing permanent damage i Note Please refer to the user s manual provided by your mainboard vendor for the installation procedure of CPU CPU Fan Heat sink and Memory Module 3 3 4 Connect Mainboard Audio Cables to activate Line out Mic in jack on the rear of the system 1 Find the audio connector which control the mainboard s audio function The connector has default jumpers on it 2 Remove the jumper 15 Iil Hardware Installation 3 Connect mainboard s audio cable built on the system plate to the audio connector on the mainboard Then the Line out Mic in jack on the rear of the system can be activated 3 3 5 Connect All other
6. can be adjusted from maximum 7 to minimum 0 Press Menu Key to save the adjustment and return to the sub menu Choose RETURN to go back to the main menu Choose EXIT to exit Or wait about 5 seconds for auto exit OSD TRANSPARENCY 28 IV LCD Panel Monitor AUDIO adjust speaker volume In the main menu choose AUDIO Press Menu key to enter the sub menu Press Up Down key to choose Mute or Volume When choose Mute press Menu key to switch ON or OFF When choose VOLUME press Menu key to show the volume level Press Up Down key to adjust the volume level The scale can be adjusted from maximum 127 to minimum 0 Press Menu Key to save the adjustment and return to the sub menu Choose RETURN to go back to the main menu Choose EXIT to exit Or wait about 5 seconds for auto exit VOLUME 7 19 Also to control audio there s hot keys A Up Y Down can be used a Press amp key to switch the mode between Mute and Volume b Press W key to show the volume of audio output Press A Up W Down to adjust the volume Press Menu to save and exit RECALL back to the present setting automatically In the main menu choose RECALL Press Menu key the system will automatically recall the present setting Choose EXIT to exit Or wait about 5 seconds for auto exit EXIT left the mai
7. check if the graphics card is correctly installed Q Hard drive or Optical drive error A 1 Check drive configuration in BIOS 2 Check drive jumper settings master slave 3 Check drive cables are properly connected 4 Check the correct drivers have been installed Q Memory Error A 1 Check the user s manual of mainboard amp memory to see if installed the correct type of memory 2 Shutdown the system disconnect the power and check if the memory is correctly installed Q No Speaker output A 1 Check if the audio cable connected properly to the Lin out port 2 Check if the monitor volume value is set properly ot Note Please be aware that this is not a comprehensive support guide For more detailed information please refer to the user s manual provided by your component vendors or contact technical support 30
8. performance intelligent multi scan TFT LCD color monitor By applying 8 bit digital data 1280 H x 1024 V 16 2M color 6Bit tFRC images are displayed on the 17 0 diagonal screen Input power voltage is 5 0V for LCD driving It is designed to be compatible with all modes between 30 KHz and 80 KHz Engineering design 29 70 KHz The microprocessor based design was implemented with the user in mind providing digital user controls for precision auto synchronization and auto sizing for convenience and user programmability for flexibility The LCD panel specifications are following 17 LCD panel specifications co a _ Typ H V ami Response Time Total msec 16ms Typ on off Watt 25W w o Inverter All black pattern mm 358 5 W X296 5 H X17 0 D 3 Temperature Range Operating Storage Shipping C 20 to 60 21 IV LCD Panel Monitor 19 LCD panel specifications mem o f une f SPECIFICATION Numberot Pres zomo mangement POB vertical stipe Display Mos Nomaiywies Number of Colors 167M RGB Bit data ViewingAngie romov GontrastRato May 7010y Tems Typ on off 396 W X324 H X17 5 D Typ Temperature Range Operating ax 0 to 50 Storage Shipping es 20 to 60 4 2 Activate the Monitor Before starting the system make sure to plug the VGA cable into to the video port of the mainboard to activate the monitor 4 3 Adjust the Monitor 4 3 1 Monitor Con
9. press Menu key again to show the level Press Up Down key to adjust the brightness level The scale can be adjusted from maximum 255 to minimum 0 Press Menu Key to return to the sub menu Choose RETURN to save the adjustment and back to the main menu Choose EXIT to exit Or wait about 5 seconds for auto exit 23 IV LCD Panel Monitor BRIGHTNESS Or in the main menu choose BRIGHTNESS Press Menu key to enter the sub menu Choose Backlight and press Menu key again to show the level Press Up Down key to adjust the backlight level The scale can be adjusted from maximum 127 to minimum 0 Press Menu Key to return to the sub menu Choose RETURN to save the adjustment and back to the main menu Choose EXIT to exit Or wait about 5 seconds for auto exit BACKLIGHT C CONTRAST adjust the difference between the light and dark areas In the main menu choose CONTRAST Press Menu key then use Up Down key to adjust the contrast level The scale can be adjusted from maximum 255 to minimum 0 Press Menu Key to return to the sub menu Choose RETURN to save the adjustment and back to the main menu Choose EXIT to exit Or wait about 5 seconds for auto exit CONTRAST D DISPLAY ADJUST adjust display s function of the picture DISPLAY 24 IV LCD Panel Monitor a H Horizontal POSITION
10. 12V 16A 5V 0 3A 12V 0 3A 5Vsb 2 0A 3 3V amp 5V Total Output 80W Dimension W x L x H 150 x 82 x 58 mm II Product Overview Y Caution Check to ensure that power switch has been switched to the correct power voltage before using The incorrect voltage source may cause tremendous damages to the system and users Consult your local engineer for assistance if necessary 2 7 Chassis All aluminum super durable chassis Anti radiation shielding and quick heat dissipation design Dimension 17 model 540 W X330 H X125 D mm 415mm height w base 19 model 570 W X360 H X125 D mm 445mm height w base Simple screw structure Strong structure when wall mounting 10 il Hardware Installation This chapter provides you the details for the installation procedures of the Mainboard Hard Disk Drive and the Extension cards of the LCD PC Barebone Please be reminded to check the hardware setup of the mainboard Hard Disk Drive and extension cards from the users manuals provided by vendors of those components before assembling the barebone 3 1 Prepare to Install 3 1 1 Installation Tools Screw driver philips cross head type Long nose pliers Forceps Anti static wrist strap or glove At least 54x40 cm THICK sponge or similar protection materials Sf OS i EN Screw Driver Pliers Forceps Rubber gloves Sponge 3 1 2 Package Checklist for Installation LCD PC Barebone AGP Riser Card PCI Riser Card
11. FEDERAL COMMUNICATIONS COMMISSION FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help CAUTION Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the users authority to operate the equipment C Tested to comply with FCC standards FOR HOME OR OFFICE USE TRADEMARKS Intel and Pentium are registered trademarks of Intel Corporation Microsoft and Windows are r
12. The manual select switch needs to be adjusted based on the different AC Input AC Input Voltage 100 127V 5A 60 Hz 200 240V 3A 50 Hz 2 Fan Grill The fan grill is where hot air is expended This airway must not be blocked or covered 3 Power Socket This is where the AC power cord connected to the system 4 Mainboard I O Ports 5 Parallel 8 Midi Joystick nt Note This mainboard I O guide is for reference only and may not be exact representation of the I O configuration and layout for your system Please refer to the user s manual provided by your mainboard vendor for the detailed information sT a II Product Overview 10 11 PS 2 Mouse Port The green 6 pin mini DIN connector is to connect a PS 2 mouse PS 2 Keyboard Port The purple 6 pin mini DIN connector is to connect a PS 2 Keyboard LAN Jack The RJ 45 jack conforms to 10Base T and 100Base TX transmission protocols and can connect to Local Area Network LAN USB 2 0 Ports The two 4 pin Universal Serial Bus USB ports can connect a wide variety of devices via the USB cable and each port is able to connect up to 128 devices via USB hubs The two USB ports conform to USB 2 0 and plug and play standards Parallel Port The 25 hole parallel port is a standard printer port that supports Enhanced Parallel Port EPP and Extended Capabilities Parallel Port ECP mode It primarily connects to a parallel printer scanner or other devices Serial Por
13. X mainboard into an all in one LCD PC in seconds All the necessary components can be found in the market which tremendously reduces the troubles of repairing or upgrading Also it s unique PCI AGP and PCI E riser cards provide system the extension flexibility Moreover to connect PC to the consumer electronics world this LCD PC barebone provides the function of playing TV DVD Video internet game Hi Fi audio and much more by equipping the SXGA LCD Panel slim optical drive latest card reader and powerful output speakers Other considerate designs include the aluminum chassis which keeps high specification systems in a heat free environment the tilt VESA and optional touch panel provide users the various application possibility The LCD PC barebone s specifications are following Mainboard Standard mATX mainboard LCD Display 17 19 SXGA TFT LCD Panel 1280 pixel H x 1024 pixel V Multi in one card reader 220W Power Supply w PFC AC Input Voltage 100 127V 5A 60 Hz 200 240V 3A 50 Hz Manual select switch 17 540 W X330 H X125 D mm 415mm height w base 19 570 W X360 H X125 D mm 445mm height w base 17 N W 9 2 KG G W 11 KG 19 N W 9 8 KG G W 11 8 KG 15 up and 3 down Optional Standard 10 cm VESA CE FCC UL ete Introduction 1 2 Package Contents E E as AGP Riser Card EE PCI Riser Card Screws v ot Note These pictures are for reference only and may not
14. adjusts the horizontal position of the display In the main menu choose DISPLAY ADJUST Press Menu key to enter the sub menu Choose H POSITION and press Menu key again to show the position level Press Up Down key to adjust the position level The scale can be adjusted from maximum 255 to minimum 0 Press Menu Key to save the adjustment and return to the sub menu Choose RETURN to go back to the main menu Choose EXIT to exit Or wait about 5 seconds for auto exit b V Vertical POSITION adjusts the vertical position of the display V POSITION In the main menu choose DISPLAY ADJUST Press Menu key to enter the sub menu Choose V POSITION and press Menu key again to show the position level Press Up Down key to adjust the position level The scale can be adjusted from maximum 31 to minimum 0 Press Menu Key to save the adjustment and return to the sub menu Choose RETURN to go back to the main menu Choose EXIT to exit Or wait about 5 seconds for auto exit c CLOCK adjusts the frequency of the pixel CLOCK In the main menu choose DISPLAY ADJUST Press Menu key to enter the sub menu Choose CLOCK and press Menu key again to show the position level Press Up Down key to adjust the position level The scale can be adjusted from maximum 255 to minimum 0 Press Menu Key to sav
15. e the adjustment and return to the sub menu Choose RETURN to go back to the main menu Choose EXIT to exit Or wait about 5 seconds for auto exit 25 IV LCD Panel Monitor d PHASE adjusts the phase of pixel clock In the main menu choose DISPLAY ADJUST Press Menu key to enter the sub menu Choose PHASE and press Menu key again to show the position level Press Up Down key to adjust the position level The scale can be adjusted from maximum 31 to minimum 0 Press Menu Key to save the adjustment and return to the sub menu Choose RETURN to go back to the main menu Choose EXIT to exit Or wait about 5 seconds for auto exit e QUALITY adjusts the scanning filter and sharpness of the picture QUALITY In the main menu choose DISPLAY ADJUST Press Menu key to enter the sub menu Choose QUALITY and press Menu key again to show the position level Press Up Down key to adjust the position level The scale can be adjusted from maximum 190 to minimum 0 Press Menu Key to save the adjustment and return to the sub menu Choose RETURN to go back to the main menu Choose EXIT to exit Or wait about 5 seconds for auto exit COLOR TEMPERATURE adjust color temperature and color scale COLOR TEMPERATURE In the main menu choose COLOR TEMPERATURE Press Menu key to enter the sub menu and there are t
16. egistered trademarks of Microsoft Corporation DOS Windows 95 98 ME 2000 NT XP are trademarks of Microsoft Corporation All other brand names mentioned in this manual are trademarks and or registered trademarks of their respective owners companies WARNING AND DISCLAIMER This manual is designed to provide information about the product Efforts have been made to make this manual as accurate as possible but no warranty of fitness is implied All the information is provided on an as is basis The author and his corresponding publishing company shall have neither liability nor responsibility to any person or entity with respect to any loss or damages arising from the information contained in this manual or from the use of the product that accompanies it Information contained in this manual is subject to change without notice The manufacturer of the product will not be held responsible for technical or editorial omissions made herein nor for the incidental or consequential damages resulting from its furnishing performance functionality or use Subsequent changes to this manual will be incorporated into the next edition We welcome any suggestion regarding this manual and product COPYRIGHT Copyright 20060 by this company The information in this users manual is protected by copyright laws No part of this manual may be photocopied or reproduced in any form without prior written authorization from the copyright owners All rights rese
17. enu Choose EXIT to exit Or wait about 5 seconds for auto exit 27 IV LCD Panel Monitor b OSD V POS adjusts OSD vertical position OSD V POS In the main menu choose OSD DISPLAY Press Menu key to enter the sub menu Choose OSD V POS and press Menu key again to show the position level Press Up Down key to adjust the position level The scale can be adjusted from maximum 174 to minimum 0 Press Menu Key to save the adjustment and return to the sub menu Choose RETURN to go back to the main menu Choose EXIT to exit Or wait about 5 seconds for auto exit c OSD TIMER adjusts the duration of OSD In the main menu choose OSD DISPLAY Press Menu key to enter the sub menu Choose OSD TIMER and press Menu key again to show the position level Press Up Down key to adjust the position level The scale can be adjusted from maximum 100 to minimum 0 Press Menu Key to save the adjustment and return to the sub menu Choose RETURN to go back to the main menu Choose EXIT to exit Or wait about 5 seconds for auto exit OSD TIMER d OSD TRANSPARENCY adjusts the transparency of OSD In the main menu choose OSD DISPLAY Press Menu key to enter the sub menu Choose OSD TRANSPARENCY and press Menu key again to show the position level Press Up Down key to adjust the position level The scale
18. he USB cable and each port is able to connect up to 128 devices via USB hubs The two USB ports conform to USB 2 0 and plug and play standards 4 Line Out Mic in Jack The Line out jack is to connect the headphones or external speakers When using external speakers disable the internal built in speakers first The Mic In jack is to connect the microphone 5 Drawable Sub stand The drawable Sub stand can be pull out to enforce the stability of the stand II Product Overview 2 3 Right Side View A lt 4 1 Ventilation Openings ral fe ty 2 Function Keys i l 4 3 Multi in One Card Reader w e 1 Ventilation Openings Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the system and to protect it from overheating 2 Function Keys 1 Power Key Turn the System and LCD Panel on or off This system uses a special one button design Press it to turn on the system and panel Press momentarily again to turn off the system and panel 2 RESET Hardware Reset Key To reset the system in case it hangs Monitor Control Keys 3 amp Up key Make cursor moves up to switch the previous function in sequence 4 Y Down key Make cursor moves down to switch the previous function in sequence 5 MENU Menu key Enter main menu and sub menu 6 AUTO Auto key Adjust vertical position phase and horizontal position and pixel clock automatically
19. hree color temperature and three colors can be chosen Press Up Down key to choose color temperature 9300K Cool 7500K Nature or 6500K Warm press Menu key to save the choice Choose Return to go back to the main menu Or press Up Down key to 26 IV LCD Panel Monitor choose color Red Green Blue Press Menu key again in the sub menu to show color level Press Up Down key to adjust the color level The scale can be adjusted from maximum 255 to minimum 0 Press Menu key to save the choice Choose Return to go back to the main menu Or choose AUTO GAIN to make the auto white balance adjusting Press Menu key to save the adjustment Choose Return to go back to the main menu Choose SAVE AND EXIT to exit Or wait about 5 seconds for auto exit Language to select the language for OSD display LANGUAGE OSD DISPLAY adjusts the function of On Screen Display OSD OSD DISPLAY a OSD H POS adjusts OSD horizontal position of OSD display OSD H POS In the main menu choose OSD DISPLAY Press Menu key to enter the sub menu Choose OSD H POS and press Menu key again to show the position level Press Up Down key to adjust the position level The scale can be adjusted from maximum 244 to minimum 0 Press Menu Key to save the adjustment and return to the sub menu Choose RETURN to go back to the main m
20. n menu When finish adjustments in the main menu choose EXIT press Menu key to exit the whole setting 29 V Troubleshooting When you encounter a problem first try to go through the recommendations followings If the error continues contact your local dealer for service information 1 Check to see if the problem persists when all the external devices are removed 2 Check if any incorrect or loose cable connections Make sure the latches on the connectors latch securely on to the receptor end 3 Be sure all the device drivers are installed properly 4 Be sure you have not performed an incorrect setting on the hardware devices in the BIOS Setup utility A faulty setting may cause the system to misbehave 5 Not all peripheral are plug and play capable You need to restart the system with these devices powered up and connected first 6 Be sure to go to BIOS setup and load DEFAULT setting after any BIOS updated 7 If external devices such as Keyboard mouse USB camera scanner SCSI card do not work correctly when connected to the system usually it s the device s own problem Consult the device s manufacturer first Q amp A Q LCD PC system won t start A Check if power cord is connected properly Q The system starts but there is no display A 1 Check if the VGA plug connected properly to the Video port 2 Check the LCD Panel settings and brightness 3 Shutdown the PC disconnect the power and
21. parts are required be sure the service technician has used replacement parts specified by the manufacturer or which have the same characteristics as the original parts Unauthorized substitutions may result in fire electric shock or other hazards TABLE OF CONTENTS Introduction 1 1 Product Specifications 1 2 Package Contents Product Overview 2 1 Front View 2 2 Rear View 2 3 Right side View 2 4 Left side View 2 5 Bottom View 2 6 System Layout 2 7 Chassis Ill Hardware Installation 3 1 Prepare to Install 3 1 1 Installation Tools 3 1 2 Packing Checklist for Installation 3 2 Installation Flowchart 3 3 Installation Procedures 3 3 1 Remove Back Chassis Cover 3 3 2 Mount the Hard Disk Drive 3 3 3 Mount the Mainboard 3 3 4 Connect Mainboard Audio Cables 3 3 4 Connect All other Cables 3 3 5 Install the Riser Cards 3 3 6 Connect VGA Cable 3 3 7 Finish the installation IV LCD Panel Monitor 4 1 LCD Panel Monitor Specifications 4 2 Activate the Monitor 4 3 Adjust the Monitor 4 3 1 Monitor Control Keys 4 3 2 Display Adjustment V Troubleshooting NO Of WwWN a PO NPN PN PNP NP NM NM NYO a a a a a a a a a a O W NY NY NYO CO ON OO On BP BPW WYN a O Introduction 1 1 Product Specifications Followed by the intelligent Easy Assemble system design this LCD PC barebone can be easily configured by the desktop PC components It gives users the freedom to install the standard P4 mAT
22. purpose of the third grounded plug If your outlet does not accommodate the plug have a qualified electrician install the correct outlet or use an adapter to ground the system product safely Do not leave the power cord where people may walk on it or place heavy objects on top of it Do not overload wall outlet and extension cords Electric power overload will cause fire or electric shock When unplug the power cord be sure to disconnect it by the plug head not by its wire Keep the power cord adapter away from children Cleaning 1 Unplug the power cord from the wall outlet before cleaning the system 2 Do not use liquid or aerosol cleaner 3 Use a damp cloth for cleaning Servicing 1 Do not attempt to service this system product yourself Opening covers or removing components may ruin your warranty and expose you to dangerous voltage or other electric hazards Refer all servicing to qualified service personnel 2 Damage Requiring Service Unplug this system from the wall outlet and refer servicing to qualified service personnel under the following conditions When the power cord or plug is damaged or frayed f liquid has been spilled or objects have fallen into the system product Ifthe system product has been exposed to rain or water Ifthe system product has been dropped or damaged The computer does not work normally after you follow the operating instructions 3 Replacement Parts When replacement
23. reflect the exact contents of the package After removing the barebone system from the package check to see if there is anything visibly wrong with it Contact your local dealer for further package information if having any doubts II Product Overview 2 1 Front View 1 LCD Display Panel 2 Build in Speaker 3 LED Indicator 4 Tilt Stand 1 LCD Display Panel This system product equipped the 17 19 inches liquid crystal display with SXGA standard 2 Build in Speaker The two 5W build in speakers on two sides output powerful stereo sound 3 LED Status Indicators Power Indicator Indicate the system status Blue lights up when the power is ON E HDD Indicator Indicate the HDD status Yellow lights up when the HDD is working 4 Tilt Stand The stand makes 15 up and 3 down adjustable tilt directions II Product Overview 2 2 Rear View 1 VESA Wall Mount Hole DA 2 Ventilation Openings AARARAAARA mirret 3 2 x USB 2 0 Ports 4 Line out Mic in Jack 5 Drawable sub stand 1 VESA Wall Mount Hole The holes for standard 10cm VESA wall mount keep the system mount on the wall easily and firmly 2 Ventilation Openings Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the system and to protect it from overheating 3 USB 2 0 Ports The two 4 pin Universal Serial Bus USB ports can connect a wide variety of devices via t
24. rved Manual Version 2 0 Release Date Jan 2006 Important Safeguard Safety Instruction 1 2 10 Keep the system away from dirt dust water or other liquid 12 13 14 15 16 Do not place heavy objects on top of the computers 18 Read Instructions All the safety and operation instructions should be read before operating the system Retain Instructions The safety and operating instructions should be retained for future reference Heed Warnings All warnings on the appliance and in the operating instructions should be heeded Follow Instructions All operation and usage guide should be followed Use only attachments recommended by the manufacturer unapproved attachments may cause hazards Subject the system on an even and stable surface Do not place it on an unstable cart stand table any rocky surfaces and shaky or vibrating place The system may fall causing serious injury to a child or adult and serious damage to the system Any mounting of the system product should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer Do not place the system product on fabric cotton materials such as bed sofa rug blanket or similar surface Do not place the system product in a bookcase or cabinet unless proper ventilation is provided Do not expose the system to moisture water or rain Ventilation Slots and openings in the cabinet
25. t The 9 pin COM1 port is for pointing devices or other serial devices through a 9 pin serial RS 232 cable Video Port The VGA DB 15 Pin Connector is to connect a VGA monitor or other VGA compatible devices Midi Joystick Port The 16 pin game port is to connect a game pad or joystick L Out Jack The Line out jack is to connect the headphones or external speakers When using external speakers the internal built in soeakers need to be disabled L In Jack The Line in jack is to connect the external CD player Tape player or other audio devices It was disabled if the build in L in jack on the rear of the system has activated Mic jack The Microphone input jack is to connect a microphone It was disabled if the build in Mic in jack on the rear of the system has activated II Product Overview 5 Extension Brackets The two brackets are where the extension cards were fixed to 2 6 System Structure 1 Hard Disk Drive 2 System Fan 3 Mainboard 4 Power Supply 1 Hard Disk Drive The Hard Disk Drive is 3 5 Height ATA 33 66 100 Ultra DMA desktop PC type 2 System Fan The System Fan is a 5 cm 3000 spin fan 3 Mainboard The mainboard is standard Intel P4 mATX mainboard 4 Power Supply Wattage 220W max Safety EMC Complier UL CUL CB TUV safety approved AC Input Voltage 100 127V 5A 60 Hz 200 240V 3A 50 Hz Manual select switch DC Output Voltage 3 3V 17A 5V 13A
26. the AGP slot to be used 3 Press the VGA card firmly into the slot of AGP riser card Then insert any screws provided to secure the VGA card with the system plate aT il Hardware Installation PCI Express Graphic Card Installation 2 Insert PCI Express riser card to the PCI Express graphic slot on the mainboard 2 Remove the slot cover from the system case in the space where the PCI Express slot to be used 3 Press the PCI Express graphic card firmly into the slot of PCI Express riser card Then insert any screws provided to secure the PCI Express graphic card with the system plate 18 il Hardware Installation 8 PCI Card Installation 1 Insert PCI riser card to the second PCI slot on the mainboard 2 Remove the slot cover from the system case in the space where the PCI slot to be used 3 Press the PCI card firmly into the slot of PCI riser card Then insert any screws provided to secure the PCI card with the system plate 19 il Hardware Installation 3 3 6 Connect VGA Cable 1 Plug the VGA cable into to the video port of the mainboard to activate the monitor 3 3 7 Finish the Installation 1 Replace the back cover Insert the screws 8 pcs firmly to close the back cover 3 Finish the installation Plug in the power cord The system is ready to go 2 WY IV LCD Panel Monitor 4 1 LCD Panel Monitor Specifications This LCD Panel Monitor is a 17 19 high
27. trol Keys There are 5 control keys on the right side of chassis for user to adjust the monitor including Power amp Up W Down MENU Menu and AUTO Auto The descriptions of these keys are followings 1 Power Key Turn the System and LCD Panel power on or off 2 dm Up key Make cursor moves up to switch the previous function in sequence 3 W Down key Make cursor moves down to switch the previous function in sequence 22 IV LCD Panel Monitor 4 MENU Menu key Enter main menu and sub menu 5 AUTO Auto key Adjust vertical position phase horizontal position and pixel clock automatically 4 3 2 Display Adjustment MAIN MENU Press Menu key to enter MAIN MENU The Control functions include Auto Setup Brightness Contrast Display Adjust Color Temperature Language OSD Display Audio Recall and Exit At the end of this menu shows the current resolution as well as horizontal and vertical frequency status A AUTO SETUP In the main menu choose AUTO ADJUST Press Menu key the system will adjust vertical position phase horizontal position and pixel clock automatically Exit automatically in 5 seconds B BRIGHTNESS This function could adjust the brightness of the picture There are two ways to adjust the brightness of display Adjust the brightness or backlight level of the panel In the main menu choose BRIGHTNESS Press Menu key to enter the sub menu Choose BRIGHTNESS and
Download Pdf Manuals
Related Search