CE EMC TEST REPORT For External USB Floppy Disk Drive Trade
Contents
1. PORT TYPES TESTED WITH Page 4 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 3 TEST METHODOLOGY 3 1 EUT SYSTEM OPERATION Insert the EUT to Host PC EMI test program was loaded and executed in Windows XP mode EUT read and wrote from Host PC Data was sent to monitor and filling the screens with upper case of H patterns The EMI test program sequentially exercised all related I O s and accessories of Host 6 Repeat3 to 5 Note Test program is self repeating throughout the test 3 2 DECISION OF FINAL TEST MODE 1 The following test mode was scanned during the preliminary test Mode 1 Data Transmit 2 After the preliminary scan the following test mode was found to produce the highest emission level Mode 1 Then the EUT configuration and cable configuration of the above highest emission mode was chosen for all final test items Page 5 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 N 4 INSTRUMENT AND CALIBRATION 4 1 MEASURING INSTRUMENT CALIBRATION The measuring equipment utilized to perform the tests documented in this report has been calibrated once a year or in accordance with the manufacturer s recommendations and is traceable to recognized national standards 4 2 TEST AND MEASUREMENT EQUIPMENT The following list contains measurement equipme2. Test Level 8 kV Air Discharge 4 Contact Discharge 4 kV Indirect Discharge Performance Criterion B Standard Required Tested by Nan Tsai Temperature E USC Humidity 55 RH Pressure 1019mbar Block Diagram of Test Setup The 470 k ohm resistors are installed per standard requirement amp its direct Support Units Indirect Support units Wooden Table Ground Reference Plane Page 25 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 Test Procedure gt S ue 10 11 The was located 0 1 m minimum from all side of the The indirect support units were located m minimum away from the but direct support unit was were located at same location as EUT on the HCP and keep at a distance of 10 with EUT A scroll H test program was loaded and executed in Windows XP mode The EUT sent above message to LCD Panel of Notebook PC and related peripherals through the test Active the communication function 1f the EUT with such port s As per the requirement of EN 55024 applying direct contact discharge at the sides other than front of EUT at minimum 50 discharges 25 positive and 25 negative 1f applicable can t be applied direct contact discharge side of EUT then the indirect discharge shall be applied One of the test points shall be subjected to at least 50 indirect discharge contact to th
3. 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 APPENDIX I PHOTOGRAPHS OF TEST SETUP LINE CONDUCTED EMISSION TEST EN 55022 Uu T REUS Page 43 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 N RADIATED EMISSION TEST EN 55022 Rev 00 Page 44 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 POWER HARMONIC amp VOLTAGE FLUCTUATION FLICKER TEST EN 61000 3 2 EN 61000 3 3 N Page 45 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 ELECTROSTATIC DISCHARGE TEST EN 61000 4 2 RADIATED ELECTROMAGNETIC FIELD TEST EN 61000 4 3 Page 46 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 FAST TRANSIENTS BURST TEST EN 61000 4 4 N L ee XY zu EE zE ru ECC 7 y 5 Page 47 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 CONDUCTED DISTURBANCE INDUCED BY RADIO FREQUENCY FIELDS TEST EN 61000 4 6 Page 48 Rev 00 Report No 60327003 E CCS Compliance Certification Services Inc Date of Issue April 11 2006 VOLTAGE DIPS INTERRUPTION TEST EN 61000 4 11 Page 49 Re
4. 3 2 EIC EN 61000 3 3 ACCREDITED IEC EN 61000 4 2 3 4 5 6 8 11 EN 50081 1 N 61000 6 3 EN 50081 2 EN 61000 6 4 0824 01 N 50081 2 EN 61000 6 1 2001 3 10 meter Open Area Test Sites 93105 90471 SA FCC 3M Semi Anechoic Chamber 965860 to perform FCC Part 15 18 measurements VCCI 3 10 meter Open Area Test Sites to perform conducted radiated VCCI 393 1066 725 879 C 402 747 912 EN 50081 1 2 EN 50082 1 2 IEC 61000 6 1 2 EN 50091 2 EN 50130 4 EN 55011 EN 55013 EN 55014 1 2 EN 55015 EN 55022 EN 55024 EN 61000 3 2 3 orway EMKO EN 61326 1 IEC 61000 4 2 3 4 5 6 8 11 EN 60601 1 2 C EN 300 328 EN 300 422 2 EN 301 419 1 EN 301 489 01 03 07 08 09 17 EN 301 419 2 3 EN 300 454 2 EN 301 357 2 N 300 328 EN 300 220 1 EN 300 220 2 EN 300 220 3 NS 47 CFR FCC Part 15 Subpart C LL N 61000 3 2 EN 61000 3 3 CNS 13439 CNS 13783 1 I CNS 14115 CNS 13438 AS NZS CISPR 22 CNS 13022 1 Tabac IEC 61000 4 2 3 4 5 6 8 11 CNS 13022 2 3 0363 CNS 13438 CNS 13783 1 alin CNS 13439 CNS 14115 3 10 meter Open Area Test Sites IC 3991 3 IC 3991 4 3M Semi Anechoic Chamber IC 6106 to perform SS 212 Issue 1 Industry Canada Q E 5 E 5 5 5 5 No part of this report be used to claim or imply product endorsement by A2LA or any agency the US Government Page 10 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 1
5. 06 15 POWER FREQUENCY MAGNETIC FIELD IMMUNITY TEST Port Enclosure Basic Standard EC EN 61000 4 8 Requirements A m Performance Criterion A Standard Required Tested by Nan Tsai Temperature 25 C Humidity 55 RH Pressure 1019mbar Block Diagram of Test Setup Induction Coil 1 2 Dimension v of EUT Signal Generator To Earth Ground Test Procedure 1 The EUT and support units were located on Ground Reference Plane with the interposition of a 0 1 m thickness insulation support Putting the induction coil on horizontal direction X direction Rotating the induction coil by 90 Y direction Rotating the induction coil by 90 again Z direction oo xe m d Recording the test result as shown in following table Page 39 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 Test conditions Field Strength 1A m Power Freq S0Hz Orientation X Y Z Orientation Field Test Result x o a Performance amp Result X Criteria A The apparatus continues to operate as intended No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance Criteria The apparatus continues to operate as intended after th
6. 1 2006 6 SETUP OF EQUIPMENT UNDER TEST 6 1 SETUP DIAGRAM see test photographs attached 1n Appendix 1 for the actual connections between EUT and support equipment 6 2 SUPPORT EQUIPMENT Notebook PC 2672 X31 99PBTKB Remark All the above equipment cables were placed in worse case positions to maximize emission signals during emission test Grounding Grounding was in accordance with the manufacturer 5 requirements and conditions for the intended use Page 11 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 N 7 LINE CONDUCTED amp RADIATED EMISSION TEST 7 1 LIMIT Maximum permissible level of Line Conducted Emission Class A Class B Frequency dBuV m dBuV m MHZ Remark The lower limit shall apply at the transition frequency Maximum permissible level of Common Mode Conducted Emission Telecommunication Ports CLASS A Voltage Limit Current Limit Quasi peak Average Remark The lower limit shall apply at the transition frequency CLASS B Voltage Limit Current Limit Quasi peak Average Remark 1 The lower limit shall apply at the transition frequency 2 According to Note 3 on table 4 of EN 55022 1996 standard a relaxation of 10 dB over the frequency range of 6 MHz to 30 MHz is allowed for high speed services having significant spectral density in this band However this relaxation is restricted to the common mode distu
7. 15 lt n lt 39 0 15x15 n Even harmonics 1 08 0 43 0 30 n 40 0 23 8 iN 5 AC mains EN 61000 3 2 2000 CLASS A CLASS B CLASSC x CLASS D Nan Tsai 25 C 55 RH Limits for Class D equipment Harmonics Max permissible Max permissible harmonics Order harmonics current current per watt mA W 2 n Odd harmonics only I w 19 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 Block Diagram of Test Setup Harmonics amp Flicker Analyzer Power Cord Power Source Test Procedure a The EUT was placed on the top of a wooden table 0 8 meters above the ground and operated to produce the maximum harmonic components under normal operating conditions for each successive harmonic component in turn b The correspondent test program of test instrument to measure the current harmonics emanated from EUT 15 chosen The measure time shall be not less than the time necessary for the EUT to be exercised Test Result No non compliance noted Remark According to clause 7 of EN 61000 3 2 equipment with a rated power of 75W or less no limits apply The test result is only for reference Page 20 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 Harmonic Emission 61000 3 2 EN 61000 3 2 EN60555 2 Comply IE
8. A o _ aries NA Page 33 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 Performance amp Result X Criteria A Criteria B Criteria The apparatus continues to operate as intended No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance The apparatus continues to operate as intended after the test No degradation of performance or loss of function 15 allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance During the test degradation of performance is however allowed Temporary loss of function is allowed provided the functions self recoverable or can be restored by the operation of controls Observation No function degraded during the tests Page 34 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 13 SURGE IMMUNITY TEST Port Power Cord Basic Standard IEC EN 61000 4 5 Requirements Line to Line 2 kV Line to Ground kV T R to Ground of Telecommunication port Performance Criterion B Stan
9. C 61000 3 2 Ed 2 1 2001 incl Amd 14 IEC 61000 4 7 Ed 1 0 1991 LEADMAN HARCS Setup File unnamed HARCS Report File unnamed USB FLOPPY DISK DRIVE USBFL BK Nan Tsai Remarks Temp 25 C Humidity 55 RH Harmoaic Emissioa IEC 61000 3 2 EN 61000 3 2 EN60555 2 2006 53 28 PM 0509 2 Uns 2799 wv 40 15 W TH DOM Range 1 Inns 0189 A p 0 927 4027 W B Y 5 vam 0 NEED CONFIRM Temp 2510 5595 RH BA F IED Fer Full Bar Actual Values Empty Bar Maximum Values Blue Current Green Voltage Red Failed Page 21 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 9 POWER VOLTAGE FLUCTUATION FLICKER TEST Port AC mains Basic Standard EN 61000 3 3 1995 2001 Limits 5 of EN 61000 3 3 Tested by Nan Tsai Temperature 39 Humidity 55 RH TEST ITEM LIMIT REMARK Pp P means short term flicker indicator Pi 0 65 Pj means long term flicker indicator ms 500 Ta means maximum time that dt exceeds 3 dinax dmax means maximum relative voltage change dc 90 dc means relative steady state voltage change Block Diagram of Test Setup Harmonics amp Flicker Analyzer Power Source Page 22 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 Test Procedure a The EUT was p
10. Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 CE EMC TEST REPORT For External USB Floppy Disk Drive Trade Name Model MOVING STAR USBFL BK Connectland LECT DISK EXT USB Issued to COMING DATA CO LTD SF 1 No13 WU CHUNG 1RD HSIN CHUNG CITY TAIPEI HSIEN TAIWAN Issued by Compliance Certification Services Inc No 81 1 Lane 210 Bade Rd 2 Luchu Hsiang TAF Taoyuan Hsien 338 Taiwan R O C 4 http www ccsemc com tw 363 service tw ccsemc com ACCREDITED Note This report shall not be reproduced except in full without the written approval of Compliance Certification Services Inc This document may be altered or revised by Compliance Certification Services Inc personnel only and shall be noted in the revision section of the document Page 1 Total Page 49 Rev 00 Report No 60327003 E Date of Issue April 11 2006 TABLE OF CONTENTS 1 TESE RESUL RE EE E ERE 3 2 4 3 I Y d e a E E EEE E OEE E IEE ENEE EEEE EAEN 5 31 EUT SYSTEM OPERATION nen nenne AA ENEN AE EEEE NN sese sanae 5 3 2 DECISION OF FINAL TEST 5 4 INSTRUMENT ANDCALIBKATION NE 6 4l MEASURING INSTRUMENT CALIBRATION vressssscccsansseoasiordicenurensonteannesunennpareteardeawuerwesonsecesicnies 6 47
11. ETIC FIELD IMMUNITY TEST eene 39 16 VOLTAGE DIPS SHORT INTERRUPTIONS 4 APPENDIX t PHOTOGRAPHS OF TEST SETUP 43 Compliance Certification Services Inc Page 2 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 1 TEST RESULT CERTIFICATION Applicant COMING DATA CO LTD SF 1 No13 WU CHUNG IRD HSIN CHUNG CITY TAIPEI HSIEN TAIWAN Manufacturer Powsun Electronic Co Ltd Zhu Wu Yulianwe Ching Shi Town Dong Guan City Guong Dong China Equipment Under Test External USB Floppy Disk Drive MOVING STAR USBFL BK Trade Name Connectland LECT DISK EXT USB Detailed EUT Description See Item 2 of this report Date of Test March 23 29 2006 Applicable Standard Class Limit Criterion Test Result 55022 1998 A1 2000 A2 2003 No non compliance noted N 61000 3 2 2000 No non compliance noted 61000 3 3 1995 A1 2001 Limit No non compliance noted 55024 1998 Al 2001 A2 2003 including EC 61000 4 2 1995 A1 1998 A2 2000 No non compliance noted EC 61000 4 3 2002 A1 2002 No non compliance noted 4 No non compliance noted EC 61000 4 5 1995 A1 2000 No non compliance noted EC 61000 4 6 1996 A1 2000 No non compliance noted EC 61000 4 8 1993 A1 2000 No non compliance noted Criterion B C C No non compliance noted Deviation from App
12. INE 1610 080 344 05 04 07 2007 Variations Simulator Test S W WinPATS V 3 26 Page 8 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 5 FACILITIES AND ACCREDITATIONS 5 1 FACILITIES All measurement facilities used to collect the measurement data are located at No 199 Chunghsen Road Hsintien City Taipei Hsien Taiwan R O C Tel 886 2 2217 0894 Fax 886 2 2217 1029 X No 11 Wugong 6th Rd Wugu Industrial Park Taipei Hsien 248 Taiwan Tel 886 2 2299 9720 Fax 886 2 2298 4045 bx No 81 1 Lane 210 Bade 2nd Rd Luchu Hsiang Taoyuan Hsien 338 Tarwan Tel 886 3 324 0332 Fax 886 3 324 5235 The sites are constructed conformance with the requirements of ANSI C63 7 ANSI C63 4 and CISPR Publication 22 Page 9 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 5 2 LABORATORY ACCREDITATIONS AND LISTINGS The test facilities used to perform Electromagnetic compatibility tests are registered or accredited by the organizations listed in the following table which includes the recognized scope specifically Country Scope of Accreditation N 55011 EN 55014 1 2 CISPR 11 CISPR 14 1 2 N 55022 EN 55015 CISPR 22 CISPR 15 AS NZS 3548 VCCI V3 2001 CFR 47 FCC Part 15 18 CNS 13783 1 CNS 13439 CNS 13438 CNS 13803 SA A2LA CNS 14115 EN 55024 IEC 801 2 IEC 801 3 IEC 801 4 IEC EN 61000
13. TESELAND MEASUREMENT EQUIPMENT coc cuite 6 5 FACILITIES AND ACCREDITATIONS 2 0 0 0 9 ws sae ea a 9 5 2 LABORATORY ACCREDITATIONS AND nennen nnns 10 SETUP OFEOUPMENT UNDER TEST 11 MEME iSo __________ 11 62 SUPPORT BOUIPMEN P 11 7 LINE CONDUCTED amp RADIATED EMISSION 12 _____ ____ __________ _________ 12 7 2 TEST PROCEDURE OF LINE CONDUCTED enne nennen nennen 13 7 3 TEST PROCEDURE OF COMMON MODE CONDUCTED EMISSION FOR TELECOMMUNK ATION 14 TEST PROCEDURE OF RADIATED taii 15 Fs c 16 wl ale 19 9 POWER VOLTAGE FLUCTUATION FLICKER TEST 22 10 ELECTROSTATIC DISCHARGE ESD IMMUNITY TEST rrr 25 11 RADIATED ELECTROMAGNETIC FIELD IMMUNITY TEST eee 29 12 FAST TRANSIENTS BURST IMMUNITY TEST 32 CG eI LEN MH 35 14 CONDUCTED DISTRBANCE INDUCED RADIO FREQUENCY FIELD IMMUNITY TEST 37 15 POWER FREQUENCY MAGN
14. Y TEST Port Enclosure Basic Standard gt IEC EN 61000 4 3 Requirements 3 V m with 80 AM 1 kHz Modulation Performance Criterion A Standard Required Tested by Nan Tsai Temperature 25 C Humidity 55 RH Pressure 1019mbar Block Diagram of Test Setup 3 meter gt 7 3 3 EUT amp Support Units S 1 5 meter 0 8m Power Amp Signal EUT Monitoring by Generator using a camera PC Controller to control S G amp PA as well as forward power Control Room Page 29 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 Test Procedure l The was located at the edge of supporting table keep 3 meter away from transmitting antenna it just the calibrated square area of field uniformity The support units were located outside of the uniformity area but the cable s connected with EUT were exposed to the calibrated field as per IEC EN 61000 4 3 setting the testing parameters of RS test software per IEC EN 61000 4 3 Performing the pre test at each side of with double specified level 6V m at 496 steps 4 From the result of pre test in step 5 choice the worst side of EUT for final test from 80 MHz to 1000 MHz at 1 steps 5 Recording the test result in following table 6 It 1s not necessary to perform test as per annex A of EN 55024 if the EUT doesn t belong to ITE product Preliminary
15. a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit and only Q P reading 1s presented The test data of the worst case condition s was recorded Page 15 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 N 7 5 TEST RESULTS Powerline Conducted Emission Operation Mode Mode 1 Test Date March 29 2006 Temperature 29 Humidity 55 RH Tested by Nan Tsai F QP Corr QP m Reading Res factor on 5n eae Margin Mem Note E EH t3 EI E ET ETT ES rM 0222 222 36 070 34 920 920 0100 36 170 170 35 020 020 62744 744 52344 744 26574 17724 724 Li 0 344 36 090 35 1860 0 100 36 190 35 260 59 106 49 106 22 916 13 826 0 447 37 810 37 380 0 100 37 910 37 480 56 93 46 93 19 021 9 451 0 586 38 550 37 440 0 100 38 650 37 540 56 000 46 000 17 350 8 460 1 229 35 520 35 650 0 100 35 620 35 750 56 000 46 000 20 380 10 250 1 430 37 340 37 270 0 100 37 440 37 370 56 000 46 000 18 560 8 630 ed Remark 1 Measuring frequencies from 0 15 MHz to 30MHz 2 The emissions measured in frequency range from 0 15 MHz to 30MHz were made with an instrument using Quasi peak detector and average detector 3 The IF bandwidth of SPA between 0 15MHz and 30MHz was 10kHz the IF bandwidth of Test Receiver between 0 15MHz and 30MHz was 9kHz 4 LI Line One L
16. dard Required Tested by Nan Tsai Temperature 25 C Humidity 55 RH Pressure 1019mbar Block Diagram of Test Setup To AC Source Surge Immunity EUT amp Support Units Controller Computer Test Procedure 1 The EUT and support units were located on a wooden table 0 8 m away from ground floor 2 Injected test voltage to the EUT ports from minimum to standard request or client request 3 Recording the test result as shown in following table Page 35 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 Test conditions Voltage Waveform 1 2 50 us Current Waveform 8 20 us Polarity Positive Negative Phase angle E 90 270 Number of Test Voltage Coupling Test Result Coupling kV Line Neutral Pos Neg Capacitive _ a Pos Neg Performance amp Result X Criteria A The apparatus continues to operate as intended No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance Criteria The apparatus continues to operate as intended after the test No degradation of performance or loss of function 15 allowed below a performance level specified by the manufacturer when the apparatus is used as intended In so
17. e antenna was placed at 10 meter away from the EUT as stated in EN 55022 The antenna connected to the Spectrum Analyzer via a cable and at times a pre amplifier would be used The Analyzer Receiver quickly scanned from 30MHz to 1000MHz The EUT test program was started Emissions were scanned and measured rotating the EUT to 360 degrees and positioning the antenna 1 to 4 meters above the ground plane in both the vertical and the horizontal polarization to maximize the emission reading level The test mode s described in Item 3 2 were scanned during the preliminary test After the preliminary scan we found the test mode described in Item 3 2 producing the highest emission level The EUT and cable configuration antenna position polarization and turntable position of the above highest emission level were recorded for the final test Procedure of Final Test EUT and support equipment were set up on the turntable as per the configuration with highest emission level in the preliminary test The Analyzer Receiver scanned from 30MHz to 1000MHz Emissions were scanned and measured rotating the EUT to 360 degrees varying cable placement and positioning the antenna 1 to 4 meters above the ground plane in both the vertical and the horizontal polarization to maximize the emission reading level Recorded at least the six highest emissions Emission frequency amplitude antenna position polarization and turntable position were recorded into
18. e front edge of horizontal coupling plane Other parts of EUT where it is not possible to perform contact discharge then selecting appropriate points of EUT for air discharge a minimum of 10 single air discharges shall be applied The application of ESD to the contact of open connectors is not required The EUT direct connection units also need to be applied ESD at the port of EUT cable connected To simulate a single ESD event either by air or by contact discharge the charge on the EUT shall be removed prior to each applied ESD pulse The charge on the metallic point or part to which the ESD pulse is to be applied for example connector shells battery charge pins metallic antennae shall be removed prior to each applied ESD test pulse When one or several metallic accessible parts are subject to the ESD test the charge shall be removed from the point where the ESD pulse 15 to be applied as no guarantee can be given about the resistance between this and other accessible points on the product Putting a mark on EUT to show tested points The following test condition was followed during the tests Remark As per IEC EN 61000 4 2 two 470k bleed resistors cable is connected between the EUT and HCP during the test applicable for power ungrounded or battery operating unit only Page 26 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 The electrostatic discharges were applied as
19. e scan by using the test receiver controlled by controller and record at least six highest emissions for showing in the test report Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit In case of measuring on the screened cable the current limit shall be applied otherwise the voltage limit should be applied The following test mode was scanned during the preliminary test Not applicable because EUT has no LAN port or modem port Page 14 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 7 4 TEST PROCEDURE OF RADIATED EMISSION N Procedure of Preliminary Test The equipment was set up as per the test configuration to simulate typical usage per the user s manual When the EUT is a tabletop system a wooden turntable with a height of 0 8 meters is used which is placed on the ground plane When the EUT is a floor standing equipment it is placed on the ground plane which has a 3 12 mm non conductive covering to insulate the EUT from the ground plane Support equipment if needed was placed as per EN 55022 All I O cables were positioned to simulate typical usage as per EN 55022 The EUT received AC power source 230VAC S0Hz from outlet socket under the turntable support equipments received power from another socket under the turntable Th
20. e test No degradation of performance or loss of function 15 allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance During the test degradation of performance is however allowed Criteria C Temporary loss of function is allowed provided the functions self recoverable or can be restored by the operation of controls Observation No function degraded during the tests Page 40 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 16 VOLTAGE DIPS SHORT INTERRUPTIONS Port AC mains Basic Standard IEC EN 61000 4 11 Requirement PHASE ANGLE 0 45 90 135 180 225 270 315 degrees Test Level Reduction Duration Performance Voltage 0595 Dips Test Level Reduction Duration Performance Voltage Uo Ur 9o 4 55 Interceptions Test Interval Min 10 sec Tested by Nan Tsai Temperature Humidity 55 RH Pressure 1019mbar Block Diagram of Test Setup To AC Source Dips Interruption EUT and Variations amp Simulator Support Units Controller Computer Test Procedure 1 The EUT and support units were located on a wooden table 0 8 m away from ground floor 2 Setting the parameter of tests and then Perform the test software of test simulator 3 Conditions changes to occu
21. follows Remark 1 For tested points to EUT refer to the enclosed pages Be aware that the red mark is for air discharge 2 NDP means that no discharge point had been occurred during that particular coupling method Performance amp Result X Criteria A The apparatus continues to operate as intended No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance Criteria The apparatus continues to operate as intended after the test No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance During the test degradation of performance is however allowed Criteria Temporary loss of function is allowed provided the functions self recoverable or can be restored by the operation of controls Observation No function degraded during the tests Page 27 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 The Tested Points of EUT Page 28 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 11 RADIATED ELECTROMAGNETIC FIELD IMMUNIT
22. ive Line L2 Line Two Neutral Line Page 16 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 Test Plots Conducted emissions Line I final Graph 70 0 da ee SL is Lt Pd RAI P IN FOU CIT TR RR 7 CTS M Lo MN O a a 2 re AY ae dBuwv gt gt gt 2 15 0 i 1 1 1 1 0 15 1 00 1000 30 00 Freqencv MHz Conducted emissions Line 2 final Graph 70 MN NBI RS NE ER NEWER S NN ao e u P ee ee ee ee PL PE S LIII al RT NT IM s PsC PCM MC PU Cu 7 299 4 2 se S va 4 AY Amplitude 22 gt gt 2 15 i 1 1 1 1 0 15 1 00 1000 30 00 Freqencv MHz Page 17 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 Radiated Emission Operation Mode Mode Test Date March 23 2006 Temperature 26 Tested by Rex Lai Humidity 55 RH Polarity Ver Hor Frequency Ant Pol De
23. laced on the top of a wooden table 0 8 meters above the ground and operated to produce the most unfavorable sequence of voltage changes under normal operating conditions b During the flick measurement the measure time shall include that part of whole operation cycle in which the EUT produce the most unfavorable sequence of voltage changes The observation period for short term flicker indicator 1s 10 minutes and the observation period for long term flicker indicator 1s 2 hours Test Result No non compliance noted Page 23 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 Measurement LEADMAN Date 2006 3 28 PM 05 23 3 V4 00 File USB FLOPPY DISK DRIVE USBFL BK Nan Tsai Remarks Temp 25 C Humidity 55 RH 229 9V Freq 49 935 Range 0 5A Irns 0 155A Ipk 0 268A cf 1 731 32 10W S 35 53VApf 0 903 Test Time 1 x 10min 10min 0 LIN Line Impedance Network L 0 24o0hm j0 150hm N 0 160hm j0 10ohm Limits Plt 0 65 Pst 1 00 dmax 4 00 dc 3 30 9o dtLim 3 30 dt gt Lim 500ms Plt 0 000 Pst P50s P10s P3s Pls 0 15 dmax dc dt gt Lim ms 1 0 000 0 000 0 000 0 000 0 000 0 052 0 000 0 000 0 000 0 000 Page 24 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 10 ELECTROSTATIC DISCHARGE ESD IMMUNITY TEST Port Enclosure Basic Standard EC EN 61000 4 2
24. licable Standard No non compliance noted _ No non compliance noted _ No non compliance noted No non compliance noted No non compliance noted _ No non compliance noted Nonon compliance noted ON EN 4 O gt NO c None The above equipment was tested by Compliance Certification Services Inc for compliance with the requirements set forth in the EMC Directive 89 336 EEC Amended by 92 31 EEC and 93 68 EEC and the technical standards mentioned above The results of testing in this report apply only to the product system which was tested Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties Approved by Reviewed by i LO u 4 Vim Gavin Lim Amanda Wu Section Manager Section Manager Compliance Certification Services Inc Compliance Certification Services Inc Page 3 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 2 EUT DESCRIPTION Product External USB Floppy Disk Drive MOVING STAR USBFL BK Trade Name Model Number connectland LECT DISK EXT USB Model Discrepanc Both of the above models are identical except for the designation of trade names and model numbers Power Supply Vdc from USB Port of Host PC USB Cable Type Shielded 1m Non detachable with a core I O Port of EUT
25. me cases the performance level may be replaced by a permissible loss of performance During the test degradation of performance is however allowed Criteria C Temporary loss of function is allowed provided the functions self recoverable or can be restored by the operation of controls Observation No function degraded during the tests Page 36 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 14 CONDUCTED DISTRBANCE INDUCED RADIO FREQUENCY FIELD IMMUNITY TEST Port AC Port and Data Line Basic Standard IEC EN 61000 4 6 Requirements 3 with 80 1 kHz Modulation Injection Method CDN M3 CDN M2 for Power Cord CDN T4 for LAN Cable Performance Criterion A Standard Required Tested by Nan Tsai Temperature 25 C Humidity 55 RH Pressure 1019mbar Block Diagram of Test Setup Side View 0 1m L 0 3m 10 cm isolation supporter EUT and Support units Power PC Controller Ground Reference Plane Top View 0 1m L 0 3m 3 5 cm isolation supporter Ground Reference Plane Power PC Amplifier Controller Page 37 Rev 00 EM Clamp CDN 10 cm isolation supporter Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 Test Procedure 1 The EUT and support units were located at a ground reference plane with the interposition of a 0 1 m thickness insulating supp
26. nt used for testing The equipment conforms to the requirement of CISPR 16 1 ANSI C63 2 and other required standards Calibration of all test and measurement including any accessories that may effect such calibration 1s checked frequently to ensure the accuracy Adjustments are made and correction factors are applied in accordance with the instructions contained in the respective manual Equipment Used for Emission Measurement Open Area Test Site 3 Name of Equipment Serial Number Due EMI Test Receiver ESVS20 838804 004 01 08 2007 Spectrum Analyzer Agilent E4446A MY43360131 01 10 2007 Pre Amplifier MITEC AFS42 00102650 924206 Pre Amplifier MITEC 6 260400 945377 Z O ze amp amp Remark The measurement uncertainty is less than 2 16dB which is evaluated as per the NAMAS NIS 81 and CISPR A 291 CDV Powerline Conducted Emission Name of Equipment Serial Number Calibration Due EMI TEST RECEIVER ROHDE amp 9kHz 30MHz SCHWARZ ESHS30 828144 003 09 27 2006 04 18 2006 Spectrum Analyzer FSP30 100112 09 23 2006 T T 2 2 TWO LINE V NETWORK 9kHz 30MHz SCHAFFNER NNB4I 03 10013 06 12 2006 LISN 10kHz 100MHz EMCO 3825 2 9106 1809 02 17 2007 Test S W LABVIEW V 6 1 Remark The measurement uncertainty is less than 2 81dB which is evaluated as per the NAMAS NIS 81 and CISPR A 29I CDV Page 6 Rev 00 Compliance Certification Services Inc Repo
27. o the LISN powering the EUT The Receiver scanned from 150kHz to 30MHz for emissions in each of the test modes During the above scans the emissions were maximized by cable manipulation The test mode s described in Item 3 2 were scanned during the preliminary test After the preliminary scan we found the test mode described in Item 3 2 producing the highest emission level The EUT configuration and cable configuration of the above highest emission level were recorded for reference of the final test Procedure of Final Test EUT and support equipment were set up on the test bench as per the configuration with highest emission level in the preliminary test A scan was taken on both power lines Line 1 and Line 2 recording at least the six highest emissions Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit The test data of the worst case condition s was recorded Page 13 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 7 3 TEST PROCEDURE OF COMMON MODE CONDUCTED EMISSION FOR TELECOMMUNICATION PORT selecting ISN for unscreened cable or a current probe for screened cable to take measurement The port of the EUT was connected to the remote side support equipment through the ISN Current Probe and communication in normal condition Making a overall rang
28. ort and the CDN was located on GRP directly setting the testing parameters of CS test software as per IEC EN 61000 4 6 qe Recording the test result in following table Test conditions Frequency Range 0 15MHz 80MHz Frequency Step 1 of fundamental Dwell Time 3 sec P CDN FCC 801 M2 16A FCC 801 M3 16A FCC 801 T4 801 2 Test Result Range MHz Modulation Cri a Performance amp Result X Criteria A The apparatus continues to operate as intended No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance Criteria The apparatus continues to operate as intended after the test No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance During the test degradation of performance is however allowed Criteria C Temporary loss of function is allowed provided the functions self recoverable or can be restored by the operation of controls Observation No function degraded during the tests Page 38 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 20
29. r at 0 degree crossover point of the voltage waveform 4 Recording the test result 1n test record form Page 41 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 Test conditions The duration with a sequence of three dips interruptions with interval of 10 s minimum Between each test event Voltage Dips Test Level Reduction Observation Ur periods Criteria Voltage Interruptions Test Level Reduction Observation Polon Ur periods Criteria tomm oT Performance amp Result Criteria A The apparatus continues to operate as intended No degradation of performance or loss of function 15 allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance Criteria B The apparatus continues to operate as intended after the test No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance During the test degradation of performance is however allowed Criteria C Temporary loss of function 1s allowed provided the functions self recoverable or can be restored by the operation of controls PASS FAIL Page 42 Rev
30. rbance converted by the cable from the wanted signal Maximum permissible level of Radiated Emission measured at 10 meter Class A Class B Frequency dBuV m dBuV m Quasi peak Quasi peak Remark The lower limit shall apply at the transition frequency Page 12 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 N 7 2 TEST PROCEDURE OF LINE CONDUCTED EMISSION Procedure of Preliminary Test The EUT was set up as per the test configuration to simulate typical usage per the user s manual When the EUT is a tabletop system a wooden table with a height of 0 8 meters is used and is placed on the ground plane as per EN 55022 see Test Facility for the dimensions of the ground plane used When the EUT is a floor standing equipment it is placed on the ground plane which has a 3 12 mm non conductive covering to insulate the EUT from the ground plane Support equipment if needed was placed as per EN 55022 All I O cables were positioned to simulate typical actual usage as per EN 55022 The test equipment EUT installed received AC power 230VAC S0Hz through a Line Impedance Stabilization Network LISN which supplied power source and was grounded to the ground plane support equipments received power from a second LISN The EUT test program was started Emissions were measured on each current carrying line of the EUT using an EMI Test Receiver connected t
31. rial Number Calibration Due Signal Generator 8648C 4108405773 09 08 2006 75 Watts IOKHz 230MHZ mplifier Research 75A250AMI 306334 Amplifier Power Sensor 51011 EMC 32864 09 07 2006 POL Fischer Custom 03018 09 08 2006 Decoupling Network Communications Inc Tower Line Coupling Fischer Custom ECC 01 M 16A 03026 09 08 2006 Decoupling Network Communications Inc Piseher Custom 16 03027 09 08 2006 Decoupling Network Communications Inc FCC 801 T2 03016 09 07 2006 Decoupling Network Communications Inc Plena dine Coupling ee FCC 801 T4 03017 09 08 2006 Decoupling Network Communications Inc EM Injection Clamp 2031 23 09 08 2006 ommunications Inc Passive Impedance Adapters 03053 amp 03054 09 08 2006 ommunications Inc Calibration Fixture Fischer Custom CE 23mm 09 08 2006 Communications Inc Fischer Custom 04024 09 08 2006 Decoupling Network Communications Inc Attenuator Attenuator Amplifier Research HFP 575 3 6 NM NF201875106 Test S W SW1005 Release 1 4 Power Frequency Magnetic Field Immunity Test Site IEC EN 61000 4 8 Tester TES 1390 020401598 12 23 2006 Electromagnetic Field Voltage Dips Short Interruption and Voltage Variation Immunity Test Site IEC EN 61000 4 11 Name of Equipment Serial Number Calibration Due Dips Interruption TRENCH PL
32. rt No 60327003 E Date of Issue April 11 2006 Power Harmonic amp Voltage Fluctuation Flicker Measurement EN 61000 3 2 amp 3 3 Name of Equipment Serial Number Due Harmonic amp Flicker Tester EMC PARTNER HARMONICS 1000 10 26 2006 Test S W HARCS Ver 4 0 Equipment Used for Immunity Measurement ESD Test Site IEC EN 61000 4 2 Name of Equipment Serial Number Calibration Due ESD Simulator ESS 2001 ESS0210582 09 13 2006 Radiated Electromagnetic Field Immunity Test Site IEC EN 61000 4 3 Name of Equipment Serial Number Calibration Due Signal Generator 8648C 4108405772 09 12 2006 150 Watts 80 1000 2 Amplifier Research 150 1000 3 306730 Amplifier 30 Watts 0 8 3 0GHZ Amplifier Research 30S1G3MI 306722 Amplifier 6 MHz Sweep Function AMREL FG 506 50608090006 05 18 2006 Generator RF Test System Controller Amplifier Research SC1000M3 306666 Field Probe Amplifier Research FP6001 305657 03 17 2007 Surge Immunity Test Site IEC EN EN 61000 4 5 Name of Equipment Serial Number Calibration Due ECAT Control Center KeyTek E Class Series 100 9502325 10 12 2006 KeyTek CM TECD TELCD 0104399 elecom Lines DOPE aE KeyTek CM I OCD 0103234 Decoupler Test S W E500 Surgeware V4 19cc Page 7 Rev 00 CCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 CS Test Site IEC EN 61000 4 6 Name of Equipment Se
33. tector Reading Correction Factor Result Limit 10m Margin MHz H V dBuV dB m dBuV m dBuV m dB mm v e ow xs som v e m xe uw v xe me an v e sw mn __ me aor __ mw w om e Lm u er wi wa we 38 xem or ww me sue omm w ew e ms ww me ma s me mm ww 903 u ve a sis mx sw Remark 1 Measuring frequencies from 30MHz to 1 GHz 2 Radiated emissions measured in frequency range from to 1000MHz were made with an instrument using Peak detector Quasi peak mode 3 Measurements above show only up to 6 maximum emissions noted or would be lesser with N A remark if no specific emissions from the EUT are recorded ie margin 20dB from the applicable limit and considered that s already beyond the background noise floor 4 The IF bandwidth of SPA between 30MHz and 1 GHz was 100 kHz Page 18 Rev 00 N ACCS Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 8 POWER HARMONICS TEST Port Basic Standard Limits Tested by Temperature Humidity Limit Limits for Class A equipment Harmonics Max permissible Order harmonics current n A Odd harmonics 2 30 0 77 0 40 0 33 3 0 21
34. test conditions Test level 6V m Steps 4 9o of fundamental Dwell Time sec __ Wm Xe H Fo __ Wm Xs A __ m Re A m Back __ m Back A m A Final test conditions Test level 3V m Steps 1 9o of fundamental Dwell Time sec Freq Range Test Result Page 30 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 Performance amp Result Criteria Criteria Criteria C The apparatus continues to operate as intended No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance The apparatus continues to operate as intended after the test No degradation of performance or loss of function 15 allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance During the test degradation of performance is however allowed Temporary loss of function is allowed provided the functions self recoverable or can be restored by the operation of controls Observation No f
35. unction degraded during the tests Page 31 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 12 FAST TRANSIENTS BURST IMMUNITY TEST Port On Power Supply Lines and Data Line Basic Standard IEC EN 61000 4 4 Requirements kV for Power Supply Line 0 5kV for LAN Cables 0 5kV for Lines Cables Performance Criterion B Standard Required Tested by Nan Tsai Temperature 25 C Humidity 55 RH Pressure 1019mbar Block Diagram of Test Setup Support Units EFT Burst Non Conductive Table surge Generator AC Line Controller Computer Comm Line gt 3m 10cm Non Conductive SS O 0 8m Injection Clamp AC Line Burst Generator Page 32 Rev 00 Compliance Certification Services Inc Report No 60327003 E Date of Issue April 11 2006 Test Procedure 1 The EUT and support units were located on a wooden table 0 8 m away from ground reference plane NO A 1 0 meter long power cord was attached to EUT during the test 29 The length of communication cable between communication port clamp was keeping within meter 4 Injected test voltage to the EUT ports from minimum to standard request or client request 5 Recording the test result as shown in following table Test conditions Impulse Frequency 5kHz Tr Th 5 50ns Burst Duration 15ms Burst Period 3Hz Neat ie A n Lu bia
36. v 00
Download Pdf Manuals
Related Search