User Guide - Smart Witness
Contents
1. 74 Optional Accessories Junction BOX eeese 76 Optional Accessories Cigarette Power 79 G Sensor Algorithm sees 80 4 www smartwitness com SAFETY ADVICE CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN DO NOT REMOVE THE COVER REFER SERVICING TO QUALIFIED SERVICE PERSONNEL gt At 720P resolution recording the camera will not create separate event files Please back up your files regularly as data might be overwritten gt Connect your vehicle s power cable Cigarette Jack to the product after starting the vehicle to avoid damage gt Install the product where it does not block the driver s view of the road Please refer to the installation section in the user manual for a full guide on where to install product gt Damages caused by production malfunction loss of data or other damages that may occur while using this product is not the responsibility of the manufacturer When malfunction occurs the product may not save all videos and the sensor may not recognise shock impacts WARNING DO NOT EXPOSE PRODUCT TO RAIN OR MOISTURE www smartwitness com 5 GPS RECEPTION 1 Activate the product in an area without large buildings to improve GPS reception For commercial purposes GPS has an average range error of more than 15 meters and the range error could be more than 100 meters depending on environmental2. STEP BY STEP 1 Peel off the reverse 3M pad and attach included bracket to the unit 2 Insert SD Card into unit Please take care to have the SD Card the correct way round Take this time to twist the camera and find the desired angle which works best for your vehicle 3 Peel off the other side of the 3M pad to reveal the sticky side then position Camera at the front of the car Secure to windscreen by applying a small amount of pressure and holding for 15 30 seconds 4 Plug into Cigarette Lighter Socket if this is your chosen power method www smartwitness com 13 3 BASIC OPERATION Automatic Start Plug the car charger cable into the cigarette lighter adaptor in your vehicle and KP1 will start automatically However KP1 will not start recording immediately after the power has been turned on It takes around 1 minute for the built in power backup system to be charged After this the internal flash memory will be ready to record PLEASE NOTE Please make sure to turn off the power of the KP1 when inserting or ejecting the SD card and the USB 3G 4G dongle LED Operation at Start up Firstly the Red LED will be ON around 6 sec then Red LED Warning and Orange LED will be ON around 12 sec l Hed LED Orange LED Blue LED Green LED will be ON in sequence around 40 50 sec Blue LED On Off Starting time around 60 70 sec J Buzzer sound operation at start up l Single Bee
3. SMARTWITNESS VEHICLE CCTV AND SAFETY SYSTEMS 3G 4G Instant Video Transmission Vehicle Accident Camera User Guide one CONTENTS PSR 6 peu ee 7 Contents EEN 12 2 Installation EE FELLE ss 13 3 Basic Operatlonpe m E enana nnman nannaa 14 Iron e S27 E 14 LED Operation at Start up oes E 14 G Sensor Calibration eere 14 Recording Modes eee OHAN AREA ARAE nnne nnn nnn 15 STERN IG AMON S 16 Over See Ennis 17 Salat ard Initialisation Een n 17 inserting The SDg amp 310p 18 Removing Ta O ad 18 Inserting 3G AG USB Modem rrrnnannnrrnnnnnnvnnvnnnnvrnnnnnnrr 19 LED Buzzer Specification rrrnnrrrrnnnrrnnnnrrrnnnrenrnnnennnnre 19 Recording When Power is Cut rerrnnrrvonernernnnnnnerennnnnennn 22 4 Software Installation esses 23 Conig ration Tool nene 23 url uecht 24 5 Configuration Software cessere eere 26 Initiale S cl _ __ E 26 Device Sellifigo x ct in MN T eee 27 Record Settings PN 29 Event Settings TM 32 Information Settings TT 6 02hn 33 3G LTE Settings ccccccsessccccsseeeeeecsseeesseeeseeesseeeeeeseeess 34 Account Settings sees 35 User Settings ccccccccccccsssseccceeeeeeeceeeseeeceeeeeeseeaseessneass 35 Server Settings see 36 2
4. wo 1 zuo voj 39 o c poc p o m Eee a o pisse EE Er sooo qo c poc eo EE ee NENNEN NER DEE 9o o e a Loo oor pop po pw 1 G mg The sensitivity difference between the G sensor average value and the value of a new G sensor 2 Hertz The amount of times the G sensor limit is breached in 1 second 92 www smartwitness com 4 Custom Mode 9 Custom Xx Y Z Threshold 0 2000 600 600 800 Hertz 1 20 4 7 2 There are 3 G sensor axis X Y Z and each axis has 2 figures The threshold figure is the sensitivity between the G sensor average value and the value of a new G sensor This value can be set between 0 2 000 Higher value means less sensitivity The second is how many times the threshold was breached continuously in Hertz per 1 30 seconds This varies from 1 20 For example X 600 4 gt This means that the alarm will trigger when the G sensor senses a 600mG 0 6G difference 4 times continuously Technical Support For Technical Support please contact your local distributor Limited Warranty This product is supplied with a 2 year warranty The Warranty excludes products that have been misused including accidental damage and damage caused by normal wear and tear In the unlikely event that you encounter a problem with this product it should be returned to the place of purchase www smartwitness com 83 Manufactured Exclusively for S
5. Event Triggered by V Panic Button d G Sensor V Over Speed Settings Initialize SD Card 36 www smartwitness com 6 Analysis Software Insert the KP1 SD card and locate the software folder now install the Analysis software once installed you can double click on the desktop icon The main screen will then be displayed as follows or Hi Control Buttons Playback SES EECH e EN 2 0 DA jnal amp Alarm Control ss splay Bar Buttons Control Buttons File Back Select Close List Tracking Save Print acKup SE li T n ve SCH bl Jud Open Eject Drive Event Privacy Save Backup Settings Files SD Data Search Settings AVI Card Playback Control Buttons Pause Next Previous Rewind Play Frame Frame t SE Hl M fe Capture Screen E ee Record 4 Video Volume Playback Speed www smartwitness com 37 Signal Alarm Indicator Brake cd um RPM Speed Left Right Reverse Henk 4 Y Alarm __ _Alarm3 Panic G Sensor Alarm Car signal Speed Video Loss event event event event event recording recording recording X recording recording file file file file file Playback Insert the SD Card to your PC Make sure that the SD Card is properly recognised After confirming that SD card is recognised correctly in the PC open the KP1 analysis software and click the Select SD Card button Then select the correct SD card from the list Shown below D Card
6. List Y E HDREC2 3 70GB 3 74GB Open SD Card Select Folder 38 www smartwitness com Then select an SD card and the click the Open SD Card button The list of data tab continuous and event is displayed on the right side of the screen The recorded data is displayed under each tab as shown below Cam CTAA WW The Playback file list can be separated from the main screen and you can hide it or change the position In addition the file list can be displayed on the screen as well by clicking the File List button You can end the Video playback by clicking the close button When finished click the disconnect safely and removing the SD card button and remove the SD card from your PC Open Files If you want to play a specific file that has been backed up on the PC or SD Card click the Open files button Select the specific MDD file you want to play and click the Open button The image of the selected file will then be displayed and you can click the Play button to play the file www smartwitness com 39 40 Drive Data KP1 can record not only video and audio GPS information speed but also vehicle information like the alarm G Sensor brake speed Pulse and RPM together The recorded information can be analysed and played through the KP1 Analysis software pl AAT LA I E n RW The default setting only displays the G sensor graphs but other information may
7. SMARTWITNESS VEHICLE CCTV AND SAFETY SYSTEMS www smartwitness com Smart Witness Unit 2 Valley Point Beddington Farm Road Croydon Surrey CRO 4WP 84 www smartwitness com
8. SPEED LIMIT EXCEEDED SD CARD 1 ERROR SD CARD 2 ERROR SD CARD 1 FULL SD CARD 2 FULL PANIC ALARM 1 ALARM 2 ALARM 3 ALARM 4 www smartwitness com 61 62 Event Notification Email from KP1 The KP1 will send an email notification when an incident happens Below explains the content and subject header of the emails Email Subject ID gt Vehicle ID gt Event Type gt Date Time For Example ID gt Y122 VVE gt G gt 16 04 2014 17 39 17 Email Body Vehicle ID Y122 VVE Driver ID Joe Policyholder Name Bloggs Limited Policy Number KP123456789 Contact Name Joe Bloggs Contact Number 07712 345 678 Type G Location 50 mph X 0 3g Y 0 2g Z 0 9g OK 3 Links 1 kml file 2 Run Google Maps 3 Request Original In the above example the type will start with the event type The different types of event are as follows G G Sensor P Panic A1 Alarm1 A2 Alarm2 A3 Alarms A4 Alarm4 The email will then attach an AVI file of the incident and show as follows AVI file 10sec QVGA 1st camera only Pre 4 seconds Event 1 second Post 5 seconds AMI file name ID Date Time avi KML file name ID Date Time kml KML Google Earth File www smartwitness com Request Original Data Send an Email to KP1 Email Subject R gt Date Time gt Password This is the user password Set using the configuration software For example H gt 2014 04 16 17 39 17 gt 5555 Send Original
9. Y122 VVE gt 2014 04 16 17 39 17 ALARM3 ALERT gt Y122 VVE gt 2014 04 16 17 39 17 ALARM4 www smartwitness com 67 9 Recording Time Table Continuous Mode SD Card in Hours 4GB 8GB 16GB 32GB 7 Yo Resolution Quality FPS vea ion ig 640x480 Normal 0 8 16 319 688 R SS D I www smartwitness com SD Card in Hours Resolution Quality FPS Resolution Quality FPS 8GB 16GB 32GB repe pe peer Super Jer wo ma pe D1 High s OD cT EC ET KEKE NLA _ De Ts To fo 4 3 166 7 i ao Jes pese peer e ow eee e Poe fr fm on oe This is a guideline only Actual results may very depending on a variety of factors Super HD 720P High 1280x720 Normal VGA 640x480 Normal QVGA 320x240 Normal Limitation of the total file number In Event Record Mode 1 camera recording The number of files is limited to a maximum of 3 000 2 camera recording The number of files is limited to a maximum of 2 000 www smartwitness com 69 In Continuous Record Mode Regardless of the number of cameras the maximum recording number is 1 000 At the Dual Continuous Event Record mode 1 camera recording maximum recording number Event folder 2 000 Normal folder 1000 2 camera recording maximum recording number Event folder 1 500 Normal folder 1000 PLEASE NOTE If the number or recorded files will exceed the maximum 1 000 then they will be ove
10. conditions like buildings and roadside trees etc 2 The temperature range for optimum operation of the GPS receiver in your car is 10 50 C 3 When using the product for the first time or after a long period more than three days it may take a little longer to recognise your current location It may take between five and thirty minutes to get GPS reception GPS reception may be impaired under the following circumstances 1 If there is an object at the end of the GPS antenna 2 If your vehicle has metallic elements on the windshield 3 If equipment generating electromagnetic waves that interfere with the GPS signal are installed in the vehicle e g other GPS devices including certain types of wireless activated alarms MP3 and CD players and camera alarms using GPS 4 If you are using a receiver connected by a cable electrical interference can be avoided by simply changing the location of the receiver antenna 5 On heavily overcast or cloudy days if the vehicle is in a covered location such as under a bridge or raised roadway in a tunnel an underground roadway or parking area inside a building or surrounded by high rise buildings 6 If GPS signal reception is poor it may take longer to locate your current position when the vehicle is moving than when it is stationary www smartwitness com 1 OVERVIEW The KP1 is the world s most advanced incident camera with powerful 3G 4G instant video transmission built
11. in tracking and telematics data The KP1 also features an optional second camera to help provide a comprehensive view of any incident and keep an eye on valuable cargo This evidence can protect a driver from many of the issues faced on the roads today e Cash for Crash Pre meditated staged accidents False Exaggerated Whiplash Claims Conflicting Reports of Actual Events Lack of Witnesses Driving Offence Allegations Speed Cameras Traffic Signal Violations etc Features Wide Angle Lens 170 providing pillar to pillar view Instant remote retrieval of court admissable evidence from both cameras Adjustable recording rates Easily upgradable comms interface 3G 4G Wifi WiMax amp Bluetooth ready Optional Audio Recording Integrates seamlessly with 3rd party telematics platforms Internal Microphone and Speaker Password protected recordings preventing unauthorised access of recordings and data on the SD card Lockable tamper resistant cover protects unauthorised access to the SD card and operation buttons www smartwitness com F Front Adjustable Bracket Lens 170 Wide Angle Lens Locking Cover Side SD Card Slot 2 Slave SD SD Card Slot 1 Master SD USB Interface For 3G 4G Dongle Molded Cable Interface 8 www smartwitness com Rear GPS G Sensor Calibration Button Panic Button Red LED Orange LED Blue LED Green LED Over Over Speed Record Communication
12. mode the BLUE LED will be blinking The buzzer will also sound twice when the event record has been triggered If set to On in the config settings Auto Format Optional When one of the SD Cards has an error and cannot record all the cards will be formatted and all data will be erased Dual Record Event amp Normal 1 Using 1x SD Card The Normal continuous record frame rate is 1fps and the file will be stored on the Normal folder www smartwitness com 15 Event record will work according to the frame rate setting For example 30 frames per second recording and the file will be stored on the Event folder 2 Using 2x SD Cards The Normal continuous record file will be stored on the SD slot No 1 The Event record file will be stored on the SD slot No 2 There will be no limit to the frame rate when using 2 cards In this mode the BLUE LED will be blinking fast and the buzzer will sound twice when the event recording has been triggered PLEASE NOTE If there are 6 beeps sounded from the unit this means that there is an SD card error or the SD card is full Driving File Record The DRV Driving file will be recorded during driving even if there are no events or video The DRV file consists of GPS and G sensor data This helps to find specific data or driving behaviours The DRV file overwrites the oldest data The DRV files will be made every 10 minutes Communication The USB 3G 4G modem is ins
13. Data Email From KP1 Email Subject ID gt Vehicle ID gt V gt Date Time For example ID gt Y122 VVE gt V gt 2014 04 16 17 39 17 V Video Attach mdd file The Max file size is 10MB 1st camera 2nd camera video When requesting the video again the email will attach an MDD file This file can only be played through the KP1 Analysis Software Request System Info Send an Email to KP1 Email Subject gt Admin Password For example gt 55555 www smartwitness com 63 Send System Info Email from KP1 Email Subject INFO gt Vehicle ID For example INFO gt Y122 VVE Email Body DR ID B2MP21400031 VEHICLE Y122 VVE DRIVER Joe CALL NUMBER 077 1234 5678 Request Preview Send an Email to KP1 Email Subject Event Type gt Date Time gt Password For example G gt 2014 04 16 17 39 17 gt 5555 Send Preview Send an Email to KP1 Email Subject ID gt Vehicle ID gt T gt Date Time For example ID gt Y122 VVE gt T gt 2013 11 16 17 39 17 T Thumbnail video 64 www smartwitness com T Thumbnail video Attach AVI file 10sec HD or 10sec VGA or 10sec QVGA 1st camera only Pre 4 seconds Event 1 second Post 5 seconds The AVI file resolution can be set in the settings on the analysis software AVI file name ID Date Time avi KML file name ID Date Time kml Remote Configure To Change KP1 Settings Send an Email to KP1 Email Subject S gt Admin Password For example S gt 555555 Attach setting i
14. Language Selectable from Japanese Korean English Spanish Russian Velocity Form Select from km h or mp h Speed Type Play information bar Selectable from the vehicle speed pulse or GPS Time Unit Selectable from 24HR or AM PM Date Format Selectable from YY MM DD MM DD YY or DD MM YY Default Layout The program will launch with the Default Layout Last Layout The program will launch with the same layout as it was when it was closed Drive Data Settings The graph scales for the Drive Data Window will be modified according to the settings www smartwitness com 59 About You can check the version information of the KP1 Analysis software Click the About button to see the below pop up About Version Info Copyrights D gz Analysis Software Version 1 0 0 10 KP1 Firmware Version Copyright C 2014 SmartWitness Group All Rights Reserved Orpm OMPH a A A Here you can check the software version and KP1 firmware version number For updates please check with your supplier distributor 60 www smartwitness com 7 Notification Email Templates Alert Message Email from KP1 The KP1 will send an email notification to alert you when an incident happens Below explains the content and subject header of the emails Email Subject ALERT gt Vehicle ID gt Date Time For Example ALERT gt Y122 VVE gt G gt 16 04 2014 17 39 17 Email Body IGNITION ON
15. Saving Time Month Event Week Info No 3G LTE Account Day of Week User Start 1 aj i nA Sunday a o End 1 i Sunday Time Zone GPS Time Sync Manual Time Setting System Speed Format Vehicle ID Driver ID ee At Start Up 4 MPH we e ks Settings Initialize SD Card mn www smartwitness com me mmi EN 33 driver from KP1 details When setting driver ID you can fill in the below form to make it easier to identify each Policyholder Name Policy Number Contact Name Contact Number 3G LTE Settings Enable the 3G LTE function on KP1 and adjust the settings for use like password User ID Authentication etc Please refer to the 3G 4G Sim Card supplier website for these settings Device Settings E Record Event Info 3G LTE Account User 4 Enable Dial No Settings 34 initialize SD Card About 998 om cose www smartwitness com Account Settings In account settings you can set an email account for KP1 for when you need to email commands This account is also the email account KP1 will send emails from Device Record Event mte 3G LTE Account User DMail J Enable User Information E Mail D Password Use SSL SMTPS POP3S e SMTP Server name Use SMTP Auth Use x POP3 Server name Admin Password 100000 999999 POP3 Check Inte
16. Speed 2 1 Bracket KP1 features a new easily adjustable bracket designed to give you the ideal viewing angle To adjust the bracket follow the steps below Remove the locking case using the key and turning anti clockwise www smartwitness com Then pinch the red and black clips and then pull the case away from KP1 Black clip in identical position on the reverse Adjust the angle of the bracket to the desired angle and slide in to lock in place When you are happy with the angle slide the case back onto KP1 and lock 10 www smartwitness com Cables KP1 comes with 2 cables One cable connects to the cigarette lighter adaptor and either junction box The second cable is unique to KP1 and connects to the second camera This cable allows both power and video to be carried to the secondary camera Please note that the second cable is only compatible with the SmartWitness S cameras SVAO21 S SVA023 S SVA025 S SVA041 S and SVA043 S KP1 Main Cable To connect the cable to either the cigarette lighter adaptor or either junction box attach by lining up the arrows on each cable and then push together To secure them together twist the silver plate as shown below www smartwitness com 11 Contents 1x KP1 3G 4G Transmission Vehicle Camera 1x SM Pad and Cable Tidy stickers 1x Locking Case 2x Keys for Locking Case 1x User Manual 12 www smartwitness com 2 INSTALLATION
17. ashi B ashing eep m e Flashing Fast CWL Over Speed 1 Speed Over Speed 2 G Sensor Calibration Beep 3 Seconds Beep Simultaneous Flashing Se Flashing Sequentially Flashing 3 Times Long Blink SD Card Initialisation Firmware Upgrade SD Card Full Sending Data 20 www smartwitness com Continued LED Buzzer Red Orange Blue Green Sound Beep 3 Record Error Simultaneous Flashing Times OSS Beep 3 Flashing Beep Slow Twice Item 3G 4G Service Error Error Without Driver Beep Once inf file 4 Seconds simultaneous ly Flashing Repeated every minute Without Setting Seconds File simultaneously Flashing Repeated every minute Beep Twice www smartwitness com 22 Recording When Power is Cut During continuous recording The continuous video recording will be recorded up to just before the end of the power is turned off Power Off d Record Off Continuous Record During event recording When the power is off and simultaneously an event is triggered there unit will not be on enough time to record the event file Therefore there is a possibility of the last event file will be lost Event ost D ss H H Event Recording Flash Memory SD Card Event amp Power Off y Flash Memory EE SD Card Lost last event file During dual recording The continuous video recording will be recorded up to just before the end of the power When
18. be added by checking the boxes in the upper part of the screen Other information included G Sensor X axis red Y axis green Z axis blue based on the positioning of the main unit is shown with the data reference point zero point calibrated and positive shocks as and negative shocks as Speed GPS measured speed is displayed in grey while the speed pulse measured speed is displayed in red RPM Displayed in purple ALL TRIGGERS signals and alarms are displayed on the bottom of the screen with the grey bar meaning the trigger is activated www smartwitness com Analyse Drive Data During the viewing click the Analyse Drive data button to view the below Analyse Drive Data screen Date Time 2014 03 11 08 35 2014 03 11 09 00 100 HEN Drive Idling alert Il Speeding ECO Overspeed alert 75 Hl Operation OverRPM a 20143 SM EW T PS Sudden Start Accel Brake X e 2 3 4 5 CT 8 9 10 EEN 12 13 14 15 16 17 18 19 20 21 22 From the calendar in the bottom right corner choose the date you wish to inspect among the dates highlighted in blue Dates that are not highlighted in blue do not have the relevant data All data from the selected date will be automatically chosen from the selection on the right You can unselect data that you do not need When data is selected click the Load button to load the data www smartwitness com 41 42 A summary of information can be found on the top o
19. ceeds the speeding limit for the amount of time set in the criteria settings The overall value is set as a ratio of the amount of time speeding to the time driving as a percentage For example if a driver drove 8 hours in a day but was speeding for 1 hour in total their score for this criteria would be 12 5 and based on the image on the previous page they would be graded as A This criteria is used in both safety and eco grading but the weights can be set separately Peak Speed Relative To Speed Limit kmh mph This option sets the grading criteria for speeding and calculates the peak speed the driver drove relative to the speed limit The value can be set from 0 999km h The assessment of this criteria is based on the speed limit option in the Analysys Criteria oetting This criteria is used for safety grading www smartwitness com Average Speed kmh mph This option sets the grading criteria for speeding and calculates the average speed the driver drove relative to the speed limit The value can be set from 0 999km h The assessment of this criteria is based on the speed limit option in the Analysys Criteria Setting This criteria is used for safety grading Excess Eco speed Count This option sets the grading criteria for eco speeding and is calculated per hour For example if a driver drove 8 hours in a day but was exceeding the eco speed limit 4 times their score for this criteria would be 0 5 and based on the image
20. citor Enables the recording of the last file before shut down PC Software KP1 Config Software KP1 Analysis Software Cigarette Jack Input DC 12V 24V 2A Output DC 5V 3A Power Input Power Adaptor Input DC12 24V Output DC 5V 3A Junction Box Input DC 12V 24V 2A Output DC 5V 3A Size WxHxD in mm 110x57x57 Weight 0 15 KG Operation Temp 10 C 55 C 72 www smartwitness com Appendix 1 Firmware Upgrade 1 To begin the firmware upgrade you will need to install the KP1 Configuration Tool software on your computer The firmware can be found on the smartwitness Support Product support page For full details on installation please go to section 4 on page 23 2 Then initialise your SD Card using the configuration software 3 Make a folder called Program on the SD Card as shown below am HDREC2 E Ji contig driving di media A software j Program 4 Copy the KP1 X X X bin file into the SD card Program folder 5 Make sure KP1 is turned off and insert the prepared SD card into KP1 SD slot 1 and turn on the power Upgrading the unit will usually take about 1 to 2 minutes PLEASE NOTE Do not turn off the power during upgrading If the upgrade fails KP1 unit should be returned to your local distributor 6 Once the upgrading is finished KP1 will automatically reboot www smartwitness com 73 Appendix 2 Optional Accessories Power Adaptor KP1 INT1 Extension Cable Juncti
21. e Next button to continue 24 www smartwitness com d e BD Setup KPI Analysis Software Select Destination Location Where should KP 1 Analysis Software be installed k Setup will install KP 1 Analysis Software into the following folder To continue dick Next If you would like to select a different folder click Browse Program Files SmartWitness KP 1 Browse At least 51 4 MB of free disk space is required lt Back wet Cancel 5 Select a destination to save the software to and click Next 18 Setup KP1 Analysis Software e me Setup KP1 Analysis Software c m se Select Start Menu Folder bay Select Additional Tasks E Where should Setup place the program s shortcuts Q Which additional tasks should be performed Q P Select the additional tasks you would like Setup to perform while installing KP 1 Analysis i Setup will create the program s shortcuts in the following Start Menu folder Software then dick Next To continue dick Next If you would like to select a different folder click Browse Additional icons v Create a desktop icon Browse en Ce 6 You can set the software to create shortcuts in both the Start Menu and the Desktop as shown above jl Setup KP1 Analysis Software Lal 33 Completing the KP1 Analysis Software Setup Wizard Setup has finished installing KP 1 Analysis Software on your computer The application may be launched by selec
22. e for this criteria would be 12 5 and based on the image on page 43 they would be graded as A The assessment of this criteria is based on the RPM limit option in the Analysis Criteria Setting This criteria is used for eco grading only Idling Count This option sets the grading criteria for idling and is calculated per hour For example if a driver drove 8 hours in a day but exceeding the idle time limit 4 times their score for this criteria would be 0 5 and based on the image on page 43 they would be graded as B The assessment of this criteria is based on the RPM limit option in the Analysis Criteria Setting This criteria is used for eco grading only PLEASE NOTE Once the grading criteria settings has been adjusted and saved it can be exported into an ini file and them imported into another version of the analysis software This means that you can set each KP1 quicker than manually adjusting the settings in each version of the software Grading Method Grades Each criteria is given a grade of A B C or D and anything lower is given a grade of F for fail Therefore each grade will be assigned a limit that if exxceed the score will go down to the next grade If the driver exceeds the limit for the D grade they will be given an F Weights Each criteria can be given a different weight when calculating the safety and eco grades to provide flexibility to the operator in assessment www smartwitness com Grad
23. ease tick these boxes when you want to make the SD Card inserted the Master SD Card 26 www smartwitness com Device Settings Device Record Camera Built In Camera 2nd Camera 2nd Camera Type Speed Source Connection Type Event Info Cam Title CAM1 36 LTE Smart Sensor Sensitivity 9 Pre set V Simple Setting Mode GPS Sensitivity 5 Standard Auto adjust G Sensor to Vehicle speed Custom Settings Initialize SD Card PLEASE NOTE Please click save if you make any changes to the configuration options Camera About e Built in Camera Check this box to use the built in camera e 24 Camera Check this box to use both the built in camera and additional camera Cam Title Rename each camera maximum 10 digits e 2 Camera Type Choose the camera type from NTSC or PAL Speed Source Select speed source from GPS or Pulse Car speed pulse www smartwitness com 27 Connection Type Choose the connection source 1 Standard Cigar Power 2 KP1 INT1 Power Adaptor 3 KP1 INT2 Junction Box Smart Sensor Sensitivity Preset Tick the checkbox to set the sensitivity of the Smart Sensor from 1 9 1 Lowest 9 highest Sensitivty should be set in consideration to the vehicles suspension and also the road condition Adjust G sensor to Vehicle Speed Automatically decreases the sensitivty of the G sensor as the vehic
24. er s view Connect cable to KP1 www smartwitness com 79 Ke KG H fe N O o lt N O D C D x o LO AX Is C D o o lt 1 Simple Mode Left Right Turn Brake or Acceleration olol ojl ofj olo ojoj of ojoj o O QD OoJo O0D o oO oO oy 0 0 O olol olofo CH ELE CO OO 0 1 G mg The sensitivity difference between the G sensor average value and the value of a new G sensor 2 Hertz The amount of times the G sensor limit is breached in 1 second www smartwitness com 80 2 Speed Mode Low Speed Left Right Turn Brake or Acceleration Oo O of c N NIOININIOJO Oo N Fort cd 1 G mg The sensitivity difference between the G sensor average value and the value of a new G sensor 2 Hertz The amount of times the G sensor limit is breached in 1 second 81 www smartwitness com 3 Speed Mode High Speed X Axis Y Axis Z Axis Level Axis Impact Brake or Acceleration Left Right Turn G mg Hertz G mg Hertz fut Hertz ICE GT Hertz Foc sets 45 5 NEN pe ee dne eee E NE o N ECNENENNE C NENNEN ERN Eee pere ces FERF YU test SET Dw MEER FEDES EN E apa esa wo 1 oo o o so 1550 ll ab NE wo 1 9o wow oe EE MES EE NENNEN ETEN o EEE J eg ee ee mo i 9 o gt ouo qo Joc poc so EE DRE Itn pec DN TEN
25. erted to the USB terminal behind the locking case To use the USB 3G 4G modem on KP1 please contact your local distributor During communication the GREEN LED will be on to show you can communicate The GREEN LED will flash when communication is performed The dongle will need to be setup with the correct APN settings using the KP1 config software If there is a communication error the unit will Beep twice If there are modem recognition errors the unit will Beep 3 times www smartwitness com Over Speed This function will allow the user to set a speed limit on the unit and alert the driver when the limit has been exceeded Excessive speeds can be set in 2 stages The first limit is 50mph and the second limit is 7Omph When the 50mph limit is reached the ORANGE LED will be lit for 5 seconds When the 70mph limit is reached the RED LED will be lit for 5 seconds The trigger on the unit will sound twice when both limits have been exceeded SD Card Initialisation Insert the SD card you want to initialise then connect the power Press and hold the Panic button for more than 3 seconds Then the 4 LED will start flashing in sequence about 20 seconds after the power is on When the Blue and Green LEDs are flashing at the same time the initialisation of the SD card will begin Initialisation operation of the SD card will take around 90 seconds depending on the size of SD card When initialisation of the SD card is comp
26. f the window including vehicle ID user ID total duration and total distance In addition you can analyse the number of over accelerations over decelerations sharp turns over speeding over RPMs that exceeded the pre set limit Top Graph The top graph shows the speed red and RPM grey and below are three indicator bars that show driving patterns The first bar shows driving blue and idling grey and the second bar shows the speed White means that the vehicle was within both the permitted speed and eco speed limit green means above eco speed but within permitted speed limit and red means above the legal speed limit The last bar shows the state of the engine where white means the engine is off blue means it is running properly within the pre set RPM limit and red means over acceleration i e exceeding the pre set RPM limit Bottom Graph The lower graph shows the G sensors The x axis is in red y axis in blue and z axis is green The indicator bar below shows jolts in the G sensor values i e G sensor values that exceed the pre set limit Grey means normal conditions red means jolts in the x axis direction blue in the y axis direction and green in the z axis direction Configurations for this function can be set by clicking the Setting button in the right bottom corner The limits for G sensor permitted speeding excessive RPM and eco speeding can be set under the Analyse tab and ranges for the two graphs can be
27. fault name is the date and time A video of each camera will be made into an AVI file The maximum length of video you can convert is one hour www smartwitness com 55 Print Image You can print selected images with accompanying information for reporting purposes To do this when playing the video press the Print Image button Shown below CYFMHRT AP HE AHAKT Hy LIE E 1i n Check all camera images you wish to include in the report Then type the title of the report and any comments about the situation or other reminders If the Privacy Masking box is checked the pre set blur effect will be applied When you click OK a preview of the report like the one below will be pop up After checking all the information press the Print to print the report 56 www smartwitness com Backup You can back up the recorded data on your PC or other data storage media KP1 offers an option to store data by type to ease management of data You can also input additional data such as Vehicle ID Driver ID title and comments to help in administration Click the Backup button SMART Check all the camera boxes you wish to back up and set the time you wish to backup The start time is when the video was paused and cannot be changed once you start this process Input all the information you wish to include in the back up file including Driver ID User ID title and comments Then select t
28. ge bat FEWN Firstly set the search range If you select the type of events you want to search for like G sensor signal alarm speed etc and then click the Search button Select the data you want to play from the list and click the Go to Video button and the video that you selected will be displayed on the screen 52 www smartwitness com Privacy Settings KP1 allows you to set the mosaic area on each channel for privacy protection When backing up the data as a JPG or AVI format and playing in the Viewer software you are able to make a mosaic processing on the area you have set To do this put the pause the video and click the Privacy settings button The privacy setting screen will pop up Using the scroll down select the camera you wish to set up On the selected camera view blur out the area you wish to protect by left clicking on the sections You can select multiple areas You can also unselect selected areas by right clicking the blurred areas To select all or clear all click on the Select all or UnSelect All buttons on the bottom respectively www smartwitness com o3 Save As JPG This function will create a still frame j peg back up of any point in the video file After finding the precise time you want to save pause the playback and click the Save JPG button and the below screen will pop up To select the channel you want to save check all the information yo
29. he folder where you wish to save the backup file The default folder is My Documents SmartWitness KP1 BACKUP Press Start to create the backup file These backed up files can be accessed from the Backup List The maximum amount of time you can back up is one hour www smartwitness com 57 Backup List You can use the data backup list to play data files easier that have been backed up To do this click the Backup List button below ef TT W ep CG DD S D me amp OO D E ackug Data UN E wo Choose the folder where the backup files are at the bottom of the screen It will automatically show the last folder that was accessed Then select the report type by scrolling down the options The files are listed showing the Date Time Vehicle ID Driver ID Title Check the box next to the file you wish to play back and click OK Finally double click the file and video files will show on the Viewer 58 www smartwitness com Software Settings You can use the data backup list to play data files easier that have been backed up To do this click the Backup List button below Click the Set Password button Password for the KP1 Analysis Software can be set with any number between 1000 9999 Note The PC Software will not be able to run without a password so please make sure to keep the password in a safe place KP1 Analysis Software Settings
30. ike to select a different folder dick Browse C Program Files ConfigTool KP 1 Browse Atleast 32 5 MB of free disk space is required Nei Gems www smartwitness com 23 6 You can choose to create a desktop icon rit Configuration f 5 Setup Configuration Tool KP1 elle Select Start Menu Folder bay Where should Setup place the program s shortcuts Q i Setup will create the program s shortcuts in the following Start Menu folder To continue click Next If you would like to select a different folder click Browse SmartWitness KP1 Browse mm 7 To finish installation click the Install button Then open the software by double clicking the shortcut icon or going to the folder in your documents Analysis Software To install KP1 Analysis Software follow the steps below If you do not have the software you can download it from www smartwitness com 1 Insert your SD card into the SD Card reader and plug into your PC 2 Drag the software onto your desktop from the software folder 3 Double click the software icon to run the software installation software j Setup KP1 Analysis Software eJ o ma Welcome to the KP1 Analysis Software Setup Wizard This will install the KP1 Analysis Software 1 0 0 10 range on your computer It is recommended that you dose all other applications before continuing Click Next to continue or Cancel to exit Setup Next gt Cancel 4 Click th
31. ime scale for the graph to be in zoom mode by selecting a value from the drop down menu 1 min 10 mins The graph settings will applied to the following window displays Manual Mode Data Search Driving Data and the Zoom Graph Default settings are Max Speed 100 km h Max G Sensor 1G Max RPM 3000 50 www smartwitness com Tracking Map During playback if you click the tracking map button the screen below will pop up showing a map of the region the route and the location of the vehicle with an orange arrow PE ut hype X OU s e 1 Le If the map is not displayed make sure that the PC is connected to the internet correctly The KP1 Analysis Software is composed of a main screen drive data screen drive data analysis screen and the tracking screen These screens can be displayed independently and their location and size changed to improve the use and management of data In addition it is also possible to display using multiple monitors By using different screen modes of Viewer software you can play analyse video data more efficiently www smartwitness com 51 Event Search With the KP1 searching and filtering the data is made easy Utilising supplementary data such as g sensor signals alarms speed and RPM you can find incidents and events quicker than monitoring the vast amounts of video and audio recordings Click the Event Search button to access the event search screen SECT e
32. ing amp Scores Each grade is assigned a score A 100 B 80 C 70 D 60 F 50 With this score the safety and eco scores are assessed by a weighted average of the relevant criteria scores The total score is an average of the safety and eco scores Below is an example of how scores can be calculated for each criteria EE NNEN NNNM ES 20 Ac fn FSuddenBrekeGout 2 como T SpeedngCount 2o A000 E om ae Hatio EE mo EDER mme Scoring Break Down Driver 1 Eco Score 20 100 100 10 100 100 20 70 100 10 70 100 10 100 100 10 100 100 91 Eco Grade A Driver 2 Eco Score 20 70 100 10 100 100 20 100 100 20 70 100 10 100 100 10 100 100 10 100 100 88 Eco Grade B As you can see each driver got 2 C grades however as they were weighted differently their eco grades are different www smartwitness com 49 Graph Display Settings The results of the driver analysis can be shown on a graph To adjust the graph display click on the Graph Display Settings option Graph Display Settings Graph Display Settings Max Smed 100 iar h Max G Sersor PS Max RPM 3000 egy Ties amn e Max Speed Set the graph s upper speed limit 0 999 km h Max G Sensor Set the graph s upper G Sensor limit by selecting a value from the drop down menu 1G 2G 4 3G Max RPM Set the graph s upper RPM limit 0 9999 Zoom Windwo Display Time Set the t
33. it has been set to 80km h for 30 seconds so therefore if the vehicle goes over this speed for over 30 seconds it will count as excessive speeding If you go over that speed but for under 30 seconds it will not count as excessive speeding RPM Limit Set the limit for excessive RPM The RPM limit can be set from 0 9999 RPM and the time can be set by selecting the drop down menu In the example above the limit has been set to 2400 RPM for 30 seconds If this limit is exceeded it will count as excessive Eco speed Limit Set the criteria for eco speed limit The eco speed limit can be set higher or lower than the speed limit and can be set from 0 999 km h and the time can be set by selecting the drop down menu In the example on page 43 the limit has been set to 60km h for 30 seconds If this limit is exceeded it will count as excessive Idle Time Limit oet the criteria for eco speed limit The idle time limit can be set for any length of time In the example on page 43 the limit has been set to 30 minutes If this limit is exceeded it will count as excessive idling All of the above criteria are used in the grading process for grading driver s safety and eco score www smartwitness com Grading Criteria Setting The criteria for grading driver s safety and eco score can be set in these settings The safety and eco grading criteria have 7 and 8 separate components respectively weighted average of these component scored are u
34. le speed increases Custom Adjust each individual axis of the sensor Threshold Sensitivity difference between the average G sensor value per second and your set G sensor value Hertz Set your threshold limit 1 20 If you chose 5 for example then if the X Y or Z value is exceeded 5 times the alarm will be triggered X Axis Left Right Force Y Axis Up Down Force Z Axis Forward Back Force Alarm Beep Turn the alarm beep On or Off Speedometer Type Set the speedometer type This is only available when you select the KP1 INT2 RPM Type Adjust the RPM type This is only available when you select the KP1 INT2 28 www smartwitness com Record Settings Evan Inte 3G LTE Account User Built In Camara 2nd Camera Resolution HD FFS To K Quality Standard Record S i Pr 1 Recording Mode Event a e Posi 10 T Telematics Data vi Record Password 1000 2596 d Dvarwrita Recordings Le e riving Time Record Audio 7 Cwarwritu S ttings Inizializa 8T Card pen Sava Close Built in Camera Resolution HD 1280x720 VGA 640x480 QVGA 320x240 2 4 Camera Resolution D1 720x480 HD1 720x240 CIF 352x240 Recording Mode Continuous Event Continuous Event 1fps continuous recording Event recording adjust the FPS from 1fps to 30fps www smartwitness com 29 Available FPS amp Max FPS per Resolution Single camera mode Built in camera only Res
35. leted KP1 will restart automatically Once completed all files will be deleted and the configurations will default to the factory settings When the SD Card initialisation is being performed the BLUE and GREEN LED will flash simultaneously PLEASE NOTE Please do not remove the SD Card during initialisation to avoid damaging or breaking the SD Card www smartwitness com 17 Inserting The SD Card To insert the SD card turn off the power and check the BLUE LED Light is off Once the LED light is off you can safely insert the card There are 2 SD Card slots for this unit please insert the first SD card into SD card slot 1 Removing The SD Card To safely remove the SD card please follow the steps below 1 Turn off the power and then check the BLUE LED 2 Press the G Sensor Calibration button for over 3 seconds and then remove the SD Card 18 www smartwitness com Inserting 3G 4G USB Modem Turn off the power and then check the BLUE LED light Once the BLUE LED light is off insert the 3G 4G USB modem 1 Red LED Over Speed 2 2 Orange LED Over Speed 1 3 Blue LED Record 4 Green LED Communication 3G 4G Signal www smartwitness com 19 ED Buzzer Red Orange Blue Green Sound On 6 Seconds X On 12 Seconds art up Flashing in sequence 40 50 seconds On Start up Com Beep once pletion Flashing Slow me Beep Twice Item ER SEH Flashing Record Fast E d Fl
36. mit 1 50 MPH Over N A w N A ww GPS Speed Limit 2 70 MPH Over N A w N A w System Warning N A w N A w Alarm Title Type Record CH Alarm Out1 Alarm Out2 Alarm Input1 Alarm1 NO w N A w NA w Alarm Out1 AlarmOut1 Alarm Out2 AlarmOut2 32 www smartwitness com 3 When using a KP1 INT2 cable you can also add an alarm and signal to the standard cable settings Shown Below Device Record Event Triggered by G Sensor Panic Button GPS Speed Limit 1 GPS Speed Limit 2 Electronic Speed Limit1 Electronic Speed Limit 2 System Warning Alarm Title Alarm Input1 Alarm1 Alarm Input2 Alarm2 Alarm Input3 Alarm3 Alarm Input4 Alarm4 Alarm Out1 AlarmOut1 Alarm Out2 AlarmOut2 Alarm Title Signal1 Left Signal2 Right Signal3 Brake Signal4 Reverse Information Settings Info 3G LTE Account Record Ch V 4 50 MPH Over 70 MPH Over 50 MPH Over 70 MPH Over Type Record CH VON e VON w NO w NO w Record CH User Alarm Out1 N A N A N A N A N A N A 4141414141414 N A Alarm Out1 N A N A N A 4 4 4 4 N A Alarm Out1 N A N A N A 4 4 lt N A Alarm Out2 N A N A N A N A N A N A AH 441414 14 N A Alarm Out2 N A N A N A 4 4414 N A Alarm Out2 N A N A N A 4 lt N A This option allows you to adjust the Time Zone GPS Time Synchronisation set your Vehicle ID and also the Driver ID FE E Configuration Settings Device Record Date Time V Daylight
37. ni file All commands have to be sent from one of the registered users that can be set in the KP1 Configure Software Daily Report Email from KP1 Email Subject ID gt Vehicle ID gt DR gt Date Time For example ID gt Y122 VVE gt DR gt 2014 04 16 17 39 17 Email Body 2014 04 15 9 39 13 gt G 2014 04 15 gt 10 39 13 gt P 2014 04 15 gt 11 39 13 gt A Total 3 www smartwitness com 65 Request Response Email from KP1 Email Subject S gt Admin Password REQUEST TITLE For example S gt 555555 gt Remote Configure Email Body INVALID PASSWORD INVALID REQUEST INVALID ARGUMENT Without setting ini file or misspelling NOT ALLOW Can t change that setting UPDATE SETTING Successfully changed setting ini ALREADY UPDATE SETTING Already changed setting ini SAME SETTING UNEXPECT Unexpected error 66 www smartwitness com 8 SMS Templates SMS Alert Message SMS from KP1 SMS Body ALERT Y122 VVE 2014 04 16 17 39 17 IGNITION ON ALERT Y122 VVE 2014 04 16 17 39 17 SPEED LIMIT EXCEEDED ALERT gt Y122 VVE gt 2014 04 16 17 39 17 SD CARD1 ERROR ALERT gt Y122 VVE gt 2014 04 16 17 39 17 SD CARD2 ERROR ALERT gt Y122 VVE gt 2014 04 16 17 39 17 SD CARD1 FULL ALERT gt Y122 VVE gt 2014 04 16 17 39 17 SD CARD2 FULL ALERT gt Y122 VVE gt 2014 04 16 17 39 17 PANIC ALERT gt Y122 VVE gt 2014 04 16 17 39 17 ALARM1 ALERT gt Y122 VVE gt 2014 04 16 17 39 17 ALAHM2 ALERT gt
38. olution CO o HD 720P 1280x720 C2 o VGA 640x480 OVGA 320x240 30 www smartwitness com C2 o Two Camera Mode Built In Camera 2 Camera Built in Camera Resolution HD 720P 1280x720 A O 0l HD 720P 1280x720 sch O 0 HD 720P 1280x720 VGA 40460 OVGA E 2 Camera D1 720x480 HD1 720x240 CIF 352x240 www smartwitness com A 30 3 A 30 3 3 D1 nm D1 30 720x480 0 0 31 Pre Event Recording Time Post Event Recording Time Adjust the Pre Post time from 5 seconds to 20 seconds Telematics Data Adjust Telematics Data recordings duration from 8 hours to 480 hours Event Settings This option allows you to set when the KP1 will record certain events for example when a panic button is pressed or G sensor is triggered 1 When using a standard power cable you can set the unit to record when triggered by the G Sensor Panic Button and or GPS Speed Limit Configuration Settings 5 ea msm i Device Record d l Event Info P 36 i TE Account User Triggered by Record CH G Sensor v Panic Button v GPS Speed Limit 37 MPH Over GPS Speed Limit2 50 MPH Over 2 When using a KP1 INT1 cable you can also add an alarm output to the above Device Record Event Info 3G LTE Account User Triggered by Record Ch Alarm Out1 Alarm Out2 G Sensor 7 N A w NA v Panic Button P N A w NA w GPS Speed Li
39. on Box Power Cable To KP1 1 Ue aa I Ext Cabl B e el LD p e S lt d d gt Power In amp Alarms Power On Off 12V 24V Switch Power Source Cable Descriptions Battery Battery 4 Alarm Alarm Out 1 Alarm Out 2 74 www smartwitness com Input Voltage DC 12V 24V 2000mA When Used at 12V When Used at 24 www smartwitness com 19 Appendix 3 76 Extension Cable Extension Cable E Optional Accessories Junction Box KP1 INT2 Junction Box Signal amp Power Cable A EB Signal amp Power Cable Med from Vehicle Cable Descriptions Battery RPM Speed Reverse Brake Right Left Battery Alarm Out 1A 1B 2A amp 2B Alarm In 1 2 3 amp 4 ACC www smartwitness com Junction Box DIP Switch 1 Switch On Low Off High ON DIP l 2 3 5 6 7 8 2 Delayed Shutdown Time Setting DIP Switch No Time 1 2 3 m perm m or om Jor me a 4 3 Power On Delay Time Setting DIP Switch No Time 4 5 or or ose ow ar um or o fue Le o me www smartwitness com d 78 4 Not Used DIP Switch No 6 7 Not Used Not Used Not Used Description 5 12v 24v Setting DIP Switch No Voltage 12V 24V When Used at 12V When Used at 24 www smartwitness com Appendix 4 Optional Accessories Cigarette Power KP1 CIGAR 12V to 5V Converter 5m Cable AEA Place cable out of driv
40. on page 43 they would be graded as B The assessment of this criteria is based on the eco speed limit option in the Analysis Criteria Setting This criteria is used for eco grading only Excess Eco speed Duration This option sets the grading criteria for eco speeding and is calculated as a ratio of time speeding and is set as a percentage For example if a driver drove 8 hours in a day but was exceeding the eco speed limit for 1 hour their score for this criteria would be 12 596 and based on the image on page 43 they would be graded as A The assessment of this criteria is based on the eco speed limit option in the Analysis Criteria Setting This criteria is used for eco grading only Excess RPM Count This option sets the grading criteria for excessive RPM and is calculated per hour For example if a driver drove 8 hours in a day but exceeded the RPM limit 4 times their score for this criteria would be 0 5 and based on the image on page 43 they would be graded as B The assessment of this criteria is based on the RPM limit option in the Analysis Criteria Setting This criteria is used for eco grading only www smartwitness com 47 48 Excess RPM Duration Ratio This option sets the grading criteria for excessive RPM over the RPM limit set This value is estimated as a percentage of the amount of time driving For example if a driver drove 8 hours in a day but was exceeding the RPM limit for 1 hour their scor
41. p after starting If beep is set to On in config settings G Sensor Calibration After installing KP1 you will need to calibrate the G Sensor To do this turn on KP1 and park the vehicle on a flat surface Then press the G Sensor Calibration button for one second This G Sensor calibration is only needed the first time KP1 is used 14 www smartwitness com Recording Modes Normal Continuous This is the default and main mode for recording In this setting the unit will begin recording after boot up and record the entire time the unit is powered Recording files will be made for 10 minutes Once a 10 minute file is made a new file will begin and so on When in normal record mode the BLUE LED will be blinking slowly to indicate normal recording Event Shock and Panic The event recording function will be automatically started by G sensor panic button or alarm You can set the G sensor parameters for the unit on your PC using KP1 config software Each event file will contain 20 seconds of footage before and up to 20 seconds after an incident The event file can also be extended by a 2 trigger during event recordings When a file is extended by a second trigger 20 seconds post recording from the event will be added to the data file with a maximum recording time of 3 minutes Once the 3 minutes has been reached the file will split and a new file will be created but the data will be continuous When in event recording
42. rove for 8 hours in one day and had 4 sudden starts during that time their score for that criteria will be 0 5 and based on the settings in the image above they would be graded as B This criteria is used in both safety and eco grading but the weights can be set sepa rately www smartwitness com 45 46 Sudden Acceleration Count This option sets the grading criteria the amount of times there is a sudden acceleration per hour The assessment of this criteria is based on the acceleration deceleration For example if a driver drove for 8 hours in one day and had 4 sudden accelerations during that time their score for that criteria will be 0 5 and based on the settings in the image on the previous page they would be graded as B This criteria is used in both safety and eco grading but the weights can be set separately Sudden Deceleration Count This option sets the grading criteria the amount of times there is a sudden deceleration per hour The assessment of this criteria is based on the acceleration deceleration For example if a driver drove for 8 hours in one day and had 4 sudden decelerations during that time their score for that criteria will be 0 5 and based on the settings in the image on the previous page they would be graded as B This criteria is used in both safety and eco grading but the weights can be set separately Speeding Count This option sets the grading criteria the amount of times the driver ex
43. rval Check Send Mail Settings Initialize SD Card About Open save Close Set email address email ID and Password Then chose your desired SSL and fill in the correct details for SMTP server and POP3 server Finally set your password and POP3 check interval The check interval time is the time between when KP1 wil check your email address for any new emails User Settings This option allows you to set receiver information such as email or SMS for each user There can be a maximum of 5 users on the KP1 www smartwitness com 35 Device Record Event info 3G LTE Account User Receiver Information Selected User User1 T Receiver E Mail Receiver Password 1000 9999 Receiver SMS Daily Report Allowed Requests Request Preview Request Original Data Request Config file Event Notify E Mail Notify E Mail Alert SMS Alert Ignition On Excessive Speed SD Card Error SD Card Full G Sensor Emergency Button larm input Alarm Input3 Alarm Input4 Alarm Input4 Settings initialize SO Card About Open sme Close Server Settings This option allows you to set the server information For server details please contact your local distributor ff Configuration Setting Device Record Event Info 3G LTE Server URL http Smartwitness com 5000 ex http DomainName 5000 DAS Key DASKEY 001 Allow Telematics Data v Allow Event Event Images Built In Camera Pre Post
44. rwritten on the SD card starting with the oldest first Therefore please backup data regularly to avoid losing any important files Event Mode Resolution Quality 16GB 32GB 1500 3000 3000 VGA 1800 3000 3000 Normal 30 1350 Events aa SA 3000 Events Events Events Resolution Quality FPS Resolution Quality FPS 4G 16GB 32GB 1500 2000 DEI os ete et D1 720x480 VGA 1800 2000 High 30 640x480 UE 700 1400 2000 2000 70 www smartwitness com Dual Recording Mode SD Card Resolution Quality FPS Resolution Quality FPS Record Folder 4GB 8GB 16GB 32GB 5 1 1 Normal ue ab iid Hours Hours Hours Hours Super Super 185 370 740 1480 1 Normal o 18 As Se VGA D1 Hours Hours Hours Hours High 640x480 720x480 m 225 450 900 1500 Events Events Events Events 1 Nora 9 18 37 74 Hours Hours Hours Hours Normal 30 Event 350 700 1400 1500 Events Events Events Events High Normal www smartwitness com 71 10 SPECIFICATIONS 1280x720 640x480 320x240 Video Resolution 2 Camera NTSC 720x480 720x240 352 240 PAL 720x576 720x288 352 288 Recording Format Video H 264 Audio G 711 Frame Rate Total 60fps Built in camera 30fps 2 Camera 30fps Normal Continuous Recording Modes Event G Sensor Panic Alarm Dual Continuous Event Event 20 sec before 20 sec after Recording Time Continuous Minimum 1 Minute Maximum 167 Hours LED 4 LEDs Red Orange Blue Green Super Capa
45. sed to determine an overall score Grading for each criteria is set to 4 levels A B C amp D and if the driver s score is lower then they will receive an F for fail Each criteria can be given a different weight depending on the importance you place on each one but all weights must add up to 100 To get into this menu enter the Settings menu and click the Grading Criteria Settings a D Gef Seat Cri De tor PS k i Acre Coat pez hac 64a DS a iL eo ng fade Sot Cat De hour Ei PS ba LES Tame 7 nant per hour a2 oe D 128 done Cont pee Fax Bad PS Lag Tyeri Count D i DS E Ld Fru Count pee Fer PA k Lig E d A x od 30 MUI UE ee lane spending Cour DAR DAD Am L Peg Sept lesket ks Geer Ler Ie Speeding Dur ston Bate am wem eo ee dryg esed Betteng iz Gpsed Lm E b Falun Beddi inn esa imt T z a ko ose B dker iz Speed Lam E k Eames Ecz apend Count pwr hour p d Exon Ee seed Duration Faro mM max 5 wa En Rewer ae iir Mira uum pum Enom Ecz apees Dress Plaga zm Xu 22 Sa Esme RPM Count pr hour Essen RPM Count per hour Ene FERA Darm Fins JE d Eom ax ha Fuca AFH rene Fort 3520 0 aom mo on enri fading Cem ri bus Pur Fear remi Tae apart lego Ux Ce Fri vesughz e Esport gar TE Cancel Sudden Start Count This option sets the grading criteria the amount of sudden starts per hour The assessment of this criteria is based on the acceleration deceleration For example if a driver d
46. set under the Component tab www smartwitness com Date Time 2014 03 11 08 35 2014 03 11 09 00 100 HEN Drive Idling alert BI Speeding ECO Overspeed alert 75 illl Operation OverRPM 50 25 Analysis Criteria Settings fn 0 Grading Criteria Settings 0 Graph Display Settings I D 8 4 2043 P gt SM TW T FS BN Continuous Sudden Start Accel Brake 1 05 Z1 2 3 4 5 j amp F S l j lo 9 10 Bll 12 13 14 15 0 RT BIO MAN All d bh a A e eU RON P 7 p Wr V Ti MIT WU I T i 16 17 18 19 20 21 22 23 24 25 26 27 28 29 05 1 1 1 1 1 8 9 Analysis Criteria Settings This option allows you to adjust the change the analysis criteria settings To access this menu go to settings click analysis criteria settings and you will be presented with the following screen Arie Ce S llrgi ems dre gie ar D s T Lom aum A ur Ei r am ED Lest zu mn d 5 ees Pretend D um y uw P be ee Ls EA ETA www smartwitness com 43 44 Acceleration Deceleration This sets the criteria for excessive acceleration and deceleration This is measured in G force so if acceleration or deceleration exceeds the G force limit it will be counted as excessive Speed Limit This option allows you to set the criteria for excessive speeding You can set the value limits between 0 999km h In the example above the lim
47. the power is off and an event is triggered there unit will not be on enough time to record the event file Therefore there is a possibility of the last event file will be lost www smartwitness com 4 Software Installation Configuration Tool Before using KP1 you will need to install both the configuration software and the analysis software to adjust KP1 settings If you do not have the software you can download it from www smartwitness com To install the configuration software follow the steps below 1 Insert your SD card into the SD Card reader and plug into your Windows PC 2 Drag the software onto your desktop from the software folder 3 Double click the software icon to run the software installation software 15 Setup Configuration Tool KP1 fo mE Welcome to the Configuration Tool KP1 Setup Wizard This will install the Configuration Tool KP 1 2 0 2 1 range on your computer It is recommended that you close all other applications before continuing Click Next to continue or Cancel to exit Setup et 4 When the above pop up comes on screen click the Next button to begin the setup 5 Then select the destination to save the software and click Next jl Setup Configuration Tool KP1 o o me Select Destination Location N Where should Configuration Tool KP 1 be installed Q L Setup will install Configuration Tool KP 1 into the following folder To continue dick Next If you would l
48. ting the installed icons Click Finish to exit Setup 7 To complete the setup click the Finish button When installed double click the shortcut icon to open the software www smartwitness com 25 5 Configuration Software Before using KP1 you will need to open the configuration software to initialise the SD card configure settings on the unit such as telematics and resolution etc Before loading the configuration software insert your SD card into the computer using an SD card Reader Initialise SD Card Firstly on the configuration tool you can initialise the SD card so it is ready for use in KP1 To do this click the Initialise SD Card button Initialize SD Card To initialise the SD card click on the above icon and you will be presented with the following screen to choose the SD card to initialise option Browse for Files or Folders SH Select SD Card Drive or Backup folder a Computer eg Floppy Disk Drive A amp Local Disk C g DVD Drive D as Removable Disk E GA Home on psf Y Cy Host on psf Z amp Google Earth Click OK when you have selected the SD card Then click the Ouick Format button and Master SD Card selection As shown Below Format SD Card i ae SD Slot 1 Master SD Card SD Slot 2 Slave SD Card If you want the Check Master SD Card software copied onto SPES Copy the Analysis setup file the SD card pl
49. u want to include from the options shown The selected information will be imprinted on the image itself Choose the folder you want to save the image to and click start The file will be saved in the default folder of My Documents SmartWitness KP1 JPG if you do not specify a Folder If you check Privacy Masking the image will include the blurs 54 www smartwitness com Save As AVI This function will create a still frame AVI video back up of any point To do this pause the video at where you wish to start saving and click the save AVI button se Pen coc voip Nar TA nr RT VERT Ani Fia Hara PN DES 1B har Check the cameras you wish to convert into an AVI file and if you wish to include audio check the Audio Ch box and scroll down to the channel you wish to include Multiple video channels can be converted but only one audio channel can be recorded and that one audio channel will be included in all AVI conversions The starting time is automatically set to the time that was paused at the start of this process and cannot be changed Select the frame rate FPS from 1 to 30 you wish to use For the best video stream use 30 FPS Check the supplementary information you wish to include in the video The selected information will show up as text on the video itself Choose the folder you wish to save the AVI file and type a file name The default folder is My DocumentsASmartWitnessAKP 1VAVI and the de
50. www smartwitness com CONTINUED 6 EE Een dE 37 See 38 DEP E NR 39 DL EDLE FFF RY RR e EEF ED NENFWD TW 40 Analyse Drive Data r 41 Analysis Criteria Settings ccccccccsssseecesssseeesseeeeeesaaees 43 Grading G terna Seg NNN ees ee eee 45 GradineptMlethiad EN 48 Graph Display BGelngp 2 2 FEE 50 Kaos M20 GJ R 5 51 Event Search a_i 52 kuer Cae EEN 53 Coe AS Le E WE 54 Dew uli WR 55 SUURU ele PT e nnn nnnm 56 BACKUP RR keen 57 Backup List EE hk 58 Software Seth PTE 59 About EE EE 60 7 Notification Email Templates 61 Alert Message tr 61 Event Notification EEN 62 Request Original Data rrrnrrnnnnnrnnrnnrrnrnnrrnnnenrnnnnnsnnnnnsene 63 Send Original Data ccccccccsssseeccceeeceeeeeeeeeeeseeeeessaaes 63 Request System Info 63 SEO SVENSK Lo ENEE 64 REGUS SNe VIC Wy eene 64 Send PRS ie wy Mc AA NN DL Ro 64 Remote Conil FN Y Y a ee 65 Daily Report NR I 65 Request Response SEET 66 8 SMS Templates SMS Alert Message rrnnnnrnnrnnnnnnnvnnnnnnnernnnnnnnnnnnnnnsvnnnnnne 67 www smartwitness com 3 CONTINUED 9 Recording Time Table eieiei a ona uu en nao a eese aucuns 68 Continuous Mode rene 68 Pee hp 70 Dual Recording Mode AAA 71 10 Specifications dim 72 Appendices ENE ET 73 Firmware Upgrade aa cess oe 73 Optional Accessories Power Adaptor
Download Pdf Manuals
Related Search