IP High Speed Dome Camera
Contents
1. Appendix C Lightning Proof and Surge Signal Proof The product adopts TVS lightning proof technology to prevent from damage by lightning strike below 1500 W and impulse signals such as surge but it is also necessary to abide by the following precautions to ensure electrical safety based on practical circumstances Keep the communication cables at least 50 meters away from high voltage equipment or cables Make outdoor cable laying out under eaves as possible as you can In open area shield cables in steel tube and conduct a single point ground to the tube Trolley wire is forbidden in such circumstances In strong thunderstorm or high faradic zone such as high voltage transformer substation extra strong lightning proof equipment must be installed Take the building lightning proof requirements into account to design the lightning proof and grounding of outdoor equipment and cable laying out in accordance with the national and industrial standards The system must be grounded with equal potentials The earth ground connection must satisfy the anti interference and electrical safety requirements and must not be short connected with high voltage electricity net When the system is grounded separately the resistance of down conductor should be lt 40 and the sectional area of down conductor should be lt 25mm Video Lightning Arrester Communication Lightning Arrester Power Lightning Arrester Lightning Rod Dorne must be ins2. ACTIVE SETTINGS SYSTEM SETTINGS 1 CAMERA TITLE 2 INFORMATION 3 PAN amp TILT 4 DELETE 5 DEFAULT 6 RESET 7 VIDEO SIGNAL 8 DATETIME 9 RETURN EDIT TITLE 1 TITLE 2 RETURN INFORMATION 1 VERSION 1 3 0 2 PROTOCOL PELCOD 3 BAUD 9600 4 ADDRESS 001 5 RETURN PAN amp TILT 1 AUTO FLIP 2 IDLE TIME 3 IDLE ACTIVE 4 ACTIVE OPTION 5 RESET ACTIVE 6 ACTIVE OPTION 7 FAN ACTIVE TEMP READ ONLY 8 RETURN DELETE ALL PRESET ALL TOUR ALL AUTO LEARNING LL SCAN DAY amp TIME 1 DATE 08 01 01 2 TIME 00 00 00 3 RETURN 29 High Speed Dome Camera User s Manual 12 System Installation 12 1 Installation 1 Dimension nn BAW UU Oi N GG y 6200 9238 Indoor Outdoor Figure 1 2 Installation Style a Wall Installation Outdoor Indoor Demension Figure 2 30 b Pendant Installation 9237 Outdoor c Ceiling Mounting CLOsE f OPEN High Speed Dome Camera User s Manual Dimension Figure 3 80 this hatch aim at the side where cable comes out the size of installation hole at Dome s pedestal Figure 4 31 High Speed Dome Camera User s Manual d Ceiling mount l T v m Chr i Ka O i aes Embed into a cutout with a diameter slightly 1 larger than 236mm 9 25 Figure 5 12 2 Installation
3. IP High Speed Dome Camera User s Manual IP High Speed Dome Camera User s Manual Chapter 1 Profile Network Camera is a kind of embedded digital surveillance product collected traditional simulation camera and network video server Adopts embedded Linux operation system and SOC hardware platform of Graim Corp And has characteristics of high efficiency on system adjustment solidified code on Flash small bulk high stability and reliability 1 1 Functions and Characteristics Basic Function gt Video compression tech adopts H 264 video compression tech high compression ratio with super agility handling gt Network function integrate TCP IP protocols and video alarm voice data supported built in WEB browser IE interview supported gt Heartbeat function host computer is able to know running state of network camera real time by heartbeat function gt PTZ control function control for PTZ kinds of decoder protocols and dome cameras supported gt Alarm function 1 channel alarm input signal parameter 1 channel alarm output on off parameter motion detective video lost mask alarm alarm link output gt Voice speech two way voice speech one way voice broadcast gt User management multi level user popedom management Compression Handling Function gt 1 channel video signal supported separate hardware compression adopts H 264 compression standard on video compression not only support change code ratio bu
4. FAN ACTIVE TEMP READ ONLY 040 8 RETURN IP High Speed Dome Camera User s Manual 9 3 Pan and Tilt The settings can control series of normal actions It plays an important role to control the image display 1 Press MENU on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Move the cursor to SYSTEM SETTINGS and enter the sub menu 3 Move the cursor to PAN amp TILT and enter the sub menu as shown in the left 9 3 1Auto Flip 1 Move the joystick and make the cursor to AUTO FLIP and enter the menu Choose ON to enable this function and disable this function while choosing OFF Operation Tips When the camera tilts downward and goes just beyond the vertical position the camera rotates 180 degrees After the camera rotates it will tilts up 90 degrees if user holds the joystick in the down position 25 PAN amp TILT OPEN 000 ON 1 AUTO FLIP 2 IDLE TIME 3 IDLE ACTIVE 4 ACTIVE OPTION 5 RESET ACTIVE LAST START 6 ACTIVE OPTION 7 FAN ACTIVE TEMP READ ONLY 040 8 RETURN PAN amp TILT OPEN 000 ON 1 AUTO FLIP 2 IDLE TIME 3 IDLE ACTIVE 4 ACTIVE OPTION 5 RESET ACTIVE LAST START 6 ACTIVE OPTION 7 FAN ACTIVE TEMP READ ONLY 040 8 RETURN PAN amp TILT 1 AUTO FLIP 2 IDLE TIME 3 IDLE ACTIVE 4 ACTIVE OPTION 5 RESET
5. 2 Press MENU on the keyboard or evoke the presets no 95 and 64 to enter the main menu choose menu to enter the SCAN SETUP as shown in the left figures 3 Choose NUMBER There are 4 scans available 4 Scan Speed Setup move the cursor to SPEED to choose from 001 063 5 Start Position Move the cursor to START POSTITION move the joystick to choose object image press OPEN to save The end position setup is the same way as start position 6 Execute the scan Make the cursor to EXECUTE and move the joystick to enter the menu The camera will execute the scans 7 DELETE Delete current scan Note 1 If the start position and end position are the same point the camera will run at constant speed 2 During the scan the speed zoom time and vertical direction will keep unchanged if these parameters are not the same for the 2 points the scanning will be subject to the start position 3 Auto scanning will be titled automatically which will be displayed on the screen like auto scan 001 20 MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE i 7 7 EXIT USER PROGRAM 1 PRESET SETUP 2 TOUR SETUP 3 AUTO LEARNING 4 SCAN SETUP 5 TIMER SETUP 6 ALARM SETUP 7 RETURN TIMER SETUP 1 NO 001 2 TRIGGER TYPE PRESET 3 TRIGGER ACTION 001 4 START TIME 00 00 5 END TIME 00 00 6 TIMING ACTIVE OFF 7
6. 2 TOUR SETUP 3 AUTO LEARNING 4 SCAN SETUP 5 TIMER SETUP 6 ALARM SETUP 7 RETURN ALARM SETUP 1 REPOSITION 2 DELAY TIME 3 ACTIVE SETTINGS 4 PLACEMENT 5 RETURN ACTIVE SETTINGS 1 NO 001 2 ALARM LINKAGE PRESET 3 ALARM ACTION 4 ALARM OUTPUT 5 RETURN PLACEMENT SET 1 PLACEMENT STATE ON 2 STATE TIME 00 00 3 END TIME 00 00 4 RETURN IP High Speed Dome Camera User s Manual 8 6 Alarm Setup The dome camera supports 7 alarm inputs and 2 outputs It can realize alarm linkage external alarm info transmitting to camera alarm position shooting evoke presets or startup auto touring auto learning and scan and decides executing the alarm output or not 1 Press MENU on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second e REPOSTION 2 options ON Delete alarm output and the camera will stop OFF delete alarm output and the camera will keep the current status The delay time must be longer than 3 seconds while setting this function to be ON e DELAY TIME Set the time that system will auto reset the alarm after current alarm inputs Values 1 to 255 seconds e OUTPUT STATUS Set relay status There are 2 states NO or NC Normal Open or Normal Close Choosing NC the relay will be closed when there is no alarm output and the replay will be opened while there is any alarm output 8 6 1 Acti
7. 34 High Speed Dome Camera User s Manual e eng tie PI AE TANG Mp TIGA T they t REN Ny Any Ze Prep Ni iso 0 Done te te ld a Ley queens len Figure 10 12 4 Disassembly and installation of Main Body 1 Quick disassembly design be easy to maintain and change the main body 2 Turn vitreous cover on its axis in CCW counter clockwise direction and separate it down 3 Then loosen knurled screw as shown bellow Hold the drier shelf look up the dome revolve main body CCW counter clockwise and fetch it out Figure1 1 Knurled screw Desiccant Bracket Dome Main Body Figure 11 4 The steps of installation are reverse to those of disassembly 12 5 Dome Configuration 35 High Speed Dome Camera User s Manual Wall Mounting Bracket TUON Ceiling Mounting Flange Ne Papi p ER 71 a Vitreous Cover Figure 12 Appendix A 24VAC Wire Diameter and Transmission Distance Comparison Chart While the wire diameter determinate and 24VAC loss rate under 10 the longest transmission distance is recommended as following chart Wire diameter mm Transmission pai 0 8000 1 000 1 250 2 000 eet m Power VA 10 283 86 451 137 716 218 1811 551 20 141 42 225 68 358 109 905 275 30 94 28 150 45 238 72 603 183 40 70 21 112 34 179 54 452 137 50 56 17 90 27 143 43 362 110 60 47 14 75 22 119 36 301 91 70 40
8. EVERYDAY ON 8 RETURN IP High Speed Dome Camera User s Manual 8 5 Timer Setup This function sets the time for executing presets scan tour and auto learning 1 Press MENU on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Move the joystick and make the cursor to USER PROGRAM and enter the sub menu 3 Move the cursor to timer Setup and enter the menu as shown in the left e NO 8Channels in total e START TIME The start time to execute relevant channel e END TIME The end time to execute relevant channel TRIGGER TYPE Choose the execution functions of pointed channels each channel can set Closing preset Scan Tour Auto learning 1 4 TRIGGER ACTION Execute relevant channel e TIMING ACTIVE Activate the timing device EVERYDAY Executing the timing switch everyday 4 If the function is closed the time period of this channel won t conflict with other channels Notice 1 During the scan touring or auto learning once the presetting time is over the current action will be stopped and the camera will resume to previous status and position before presetting time 2 Idle running function s not allowed during the timing period 3 The timing functions will not be executed while setting presets recording auto learning setting start end positions and menu status etc 21 USER PROGRAM 1 PRESET SETUP
9. INFORMATION 3 PAN amp TILT 4 DELETE 5 DEFAULT 6 RESET 7 VIDEO SIGNAL PAL 8 DATE amp TIME 9 RETURN DAY amp TIME 1 DATE 08 01 01 2 TIME 00 00 00 3 RETURN 10 Language setup MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE i 7 EXIT IP High Speed Dome Camera User s Manual 9 7 Date amp Time 1 Press MENU on the keyboard or evoke the presets no 95 and 64 to enter the main menu 2 Move joystick and make the cursor to SYSTEM SETTING and enter the sub menu 3 Move joystick and make the cursor to Date amp time and enter the menu 4 Move cursor to TIME or DATE clockwise or anticlockwise rotate the joystick cap to adjust the time and date exit the interface to save The date shows as year month day and time will be minute second in orders 1 Press MENU on keyboard or call No 95 No 64 preset position then enter main menu 2 Move cursor to LANGUAGE 3 Move joystick to select Chinese or English menu exit the interface to save the settings 28 11 Carrera Menu Index DISPLAY SETTINGS 1 CAMERA TITLE 2 ADDRESS 3 PRESET TITLE 4 ZOOM MULTIPLE 5 COORDINATE 6 TEMPERATURE 7 DATE 8 TIME 8 RETURN CAMERA SETTINGS 1 ZOOM SPEED 2 BLC 3 FLAME HEAP 4 D ZOOM 5 VIDEO SYNC 6 B amp W SETTINGS 7 ADVANCED SETTINGS 8 RETURN 1 B amp W COLOR SWITCH 2 BW
10. Pinyin numbers symbol and English etc Characters include 0 9 A Z Chinese and symbol etc cIa IP High Speed Dome Camera User s Manual 9 2 Information MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE i 7 7 EXIT 1 Press Menu on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Move the cursor to SYSTEM SETTINGS and enter the sub menu 3 Move the cursor to INFORMATION the default info of the camera will be displayed on the screen Default info includes software version camera address and communication parameters SYSTEM SETTINGS 1 CAMERA TITLE 2 INFORMATION 3 PAN amp TILT 4 DELETE 5 DEFAULT 6 RESET 7 VIDEO SIGNAL PAL 8 DATE amp TIME 9 RETURN INFORMATION 1 VERSION 1 0 0 2 PROTOCOL PELCOD 3 BAUD 9600 4 ADDRESS 001 5 RETURN 24 MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE i 7 EXIT SYSTEM SETTINGS 1 CAMERA TITLE 2 INFORMATION 3 PAN amp TILT 4 DELETE 5 DEFAULT 6 RESET 7 VIDEO SIGNAL PAL 8 DATE amp TIME 9 RETURN PAN amp TILT OPEN 000 ON 1 AUTO FLIP 2 IDLE TIME 3 IDLE ACTIVE 4 ACTIVE OPTION 5 RESET ACTIVE LAST START 6 ACTIVE OPTION 7
11. SANYO camera here it is Gamma setup which include OFF ON and BRIGHTNESS ENHANCING 1 This function correlates the camera model and parameter That is not effective if the IP High Speed Dome Camera User s Manual MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE i 7 7 EXIT 6 4 D Zoom Settings 1 Press MENU on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Move the joystick and make the cursor to CAMERA SETTINGS enter the menu 3 Move the joystick and make the cursor to D ZOOM choose ON to control the zoom and choose OFF to enable this function 4 Move the joystick up and down to Return to exit the menu and save the settings Operation Tips CAMERA SETTINGS When the digital zoom function is activated the camera s largest zoom times is the 1 ZOOM SPEED HIGH optics zoom multiplying the digital zoom while the digital zoom function is enabled 2 BLC CLOSE the camera s largest zoom time is just the optics zoom time 3 FLAME HEAP CLOSE 4 D ZOOM OPEN 5 VIDEO SYNC OPEN If the camera block is Sony LG or CNB branded the digital zoom option is on off 6 B W SETTINGS 7 ADVANCED SETTINGS 8 RETURN 12 MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4
12. SCHEDULE 3 COLOR SCHEDULE 4 RETURN 1 EXPOSURE 2 AE 3 Al 4 BRIGHTNESS 5 WB 6 RED GAIN 7 BLUE GAIN 8 RETURN AUTO 00 00 00 00 IP High Speed Dome Camera User s Manual MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE E 5 7 Exit USER PROGRAM 1 PRESET SETUP 2 TOUR SETUP 3 SCAN SETUP 4 AUTO LEARNING 5 TIMING SETUP 6 ALARM SETUP 7 RETURN PRIVACY MASK 1 1 MASK NO 00 2 MASK AREA 3 ACTIVE OFF 4 DELETE 5 RETURN PRESET SETUP EDIT PRESET TITLE 1 NO 001 1 TITLE PRESET 005 2 SET EL 2 RETURN 4 DELETE 5 EDIT TITLE 6 RETURN TOUR SETUP 1 NO 2 STAY TIME 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 3 EXECUTE 4 RETURN 001 1 TITLE AUTO LEARNING1 2 RETURN 1 NO 2 REC TRACK 3 EXECUTE 4 DELETE 5 EDIT TITLE 6 RETURN SCAN SETUP 1 NO 2 PATH 3 SPEED 4 START POSITION 5 END POSITION 6 EXECUTE 7 DELETE 8 RETURN 1 NO 2 TRIGGER TYPE 3 TRIGGER ACTION 001 4 START TIME K 5 END TIME 6 TIMING ACTIVE 7 EVERYDAY 8 RETURN PLACEMENT SET ALARM SETUP 1 PLACEMENT STATE ON 1 REPOSITION 001 1 NO 001 2 STATE TIME 00 00 2 DELAY TIME 009 2 ALARM LINKAGE PRESET 3 END TIME 00 00 3 ACTIVE SETTINGS 3 ALARM ACTION 001 4 ALARM OUTPUT 5 RETURN 4 PLACEMENT 5 RETURN 5 RETURN
13. SETTINGS 8 RETURN ADVANCED SETTINGS 1 EXPOSURE AUTO 2 AE 1 50 3 Al F1 4 4 BRIGHTNESS F1 4 10DB 5 WB AUTO 6 RED GAIN 7 BLUE GAIN 8 RFTURN IP High Speed Dome Camera User s Manual 6 7 Advanced Settings 1 Press Menu on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Move the joystick and make the cursor to CAMERA SETTINGS enter the menu 3 Move the joystick and make the cursor to ADVANCED SETTINGS and enter the sub menu shown in the left 6 7 1 Exposure Mode 1 Move the cursor to EXPOSURE and there are the following modes for selection e AUTO Default setting e BRIGHTNESS PREFs e Al PREFs e AE PREFs 2 While choosing Al PREFs mode the iris value F1 4 can be set Move the joystick to choose the proper iris the setup will be saved when exiting the menu e 1 50 Shutter speed It can be set only when AE PREFs is chose F1 4 Al value It can be set only when Al PREFs is chose e F2 0 10dB Brightness It can be set only when BRIGHTNESS PREFs is chose Operation Tips The picture quality relates to light exposure i e the light throughput that can ensure the CCD to gain clear image The exposure relates to the light through time decided by AE SPEED and light through area decided by Iris value The camera calculates the proper exposure according to the object b
14. Steps Taking wall installation style as example 1 Unpacking the carton and carefully take out the dome camera and its attachments 2 According to the size of Dome drill the installation hole in the wall and fixed expander bolts Also can drill hole according to fixed hole of bracket 3 Rotate the vitreous cover CCW counterclockwise and take it out see Figure 6 Paa En Coding Switch Figure 6 4 Set up camera protocol and baud rate according to Table 2 referring to Figure 4 1 Set the dome address ID according to Table 1 5 Rotate the vitreous cover CW clockwise to install Dome 6 Fix the bracket on the main body of dome rotate the Dome CW clockwise and keep the bracket hole and the mounting flange in line Tighten the three screws refer to Figure7 32 High Speed Dome Camera User s Manual f 1 Aligning main body with bracket pi 2 CW rotate Dome tighten 3 screws knurled screws 3 Push the cover plate up tightly 4 Tighten knurled screws Figure 7 7 Fetch the signal cable video cable and power wires from bracket Fix the cover plate tighten the knurled screw refer to Figure 6 8 Fix the assembled Dome on the wall and tighten 4 PCS knurled screws 9 Instruction of surface installation According to the size of Dome s fixed board drill the installation hole on the ceiling and fixed expander bolts Also can drill hole according to fixed hole of fixed boar
15. USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGES 7 7 EXIT CAMERA SETTINGS 1 ZOOM SPEED HIGH 2 BLC CLOSE 3 FLAME HEAP CLOSE 4 D ZOOM OPEN 5 VIDEO SYNC OPEN 6 B W SETTINGS 7 ADVANCED SETTINGS 8 RETURN MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE i 7 7 EXIT CAMERA SETTINGS 1 ZOOM SPEED HIGH 2 BLC CLOSE 3 FLAME HEAP CLOSE OPEN OPEN 4 D ZOOM 5 VIDEO SYNC 6 B amp W SETTINGS 7 ADVANCED SETTINGS 8 RETURN IP High Speed Dome Camera User s Manual 6 5 Video Sync 1 Press Menu on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Move the joystick and make the cursor to camera settings enter the menu 3 Move the joystick and make the cursor to VIDEO SYNC and setup this function choosing OFF for internal sync and OPEN for external sync Operation Tips When several speed dome cameras use one terminal video device the image may flicker meanwhile switching the pictures To solve this problem set each camera to external sync and adjust the sync value 6 6 B amp W Color Switch 1 Press MENU on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Move the joystick and make the cursor to CAMERA SETTINGS and enter
16. 12 64 19 102 31 258 78 80 35 10 56 17 89 27 226 68 90 31 9 50 15 79 24 201 61 100 28 8 45 13 71 21 161 C55 110 25 7 41 12 65 19 164 49 120 23 7 37 11 59 17 150 45 130 21 6 34 10 55 16 139 42 36 High Speed Dome Camera User s Manual 140 20 6 32 9 51 15 129 39 150 18 5 30 9 47 14 120 36 160 17 5 28 8 44 13 113 34 170 16 4 26 7 42 12 106 32 180 15 4 25 7 39 11 100 30 190 14 4 23 7 37 11 95 28 200 14 4 22 6 35 10 90 27 Appendix B Wire Gauge Conversion Chart ie AWG Swe odode ga Approximate Approximate crane 0 050 43 47 0 00196 0 060 42 46 0 00283 0 070 41 45 0 00385 0 080 40 44 0 00503 0 090 39 43 0 00636 0 100 38 42 0 00785 0 110 37 41 0 00950 0 130 36 39 0 01327 0 140 35 0 01539 0 160 34 37 0 02011 0 180 33 0 02545 0 200 32 35 0 03142 0 230 31 0 04115 0 250 30 33 0 04909 0 290 29 31 0 06605 0 330 28 30 0 08553 0 350 27 29 0 09621 0 400 26 28 0 1237 0 450 25 0 1602 0 560 24 24 0 2463 0 600 23 23 0 2827 0 710 22 22 0 3958 0 750 21 0 4417 37 High Speed Dome Camera User s Manual 0 800 20 21 0 5027 0 900 19 20 0 6362 1 000 18 19 0 7854 1 250 16 18 1 2266 1 500 15 1 7665 2 000 12 14 3 1420 2 500 4 9080 3 000 7 0683
17. 2 2 Performance Characteristics The speed dome cameras adopt bran new design and are featured as compact and metal structure It is equipped with thermostatic apparatus inside and has rapid heat dissipation function It is easy and convenient to install The surveillance is more privy with the inside black cover The camera rotates flexibly with low noise and wide coverage providing excellent image quality for users Internal Decoder 220 presets 4 Auto learning 4 limited scan Internal permanent calendar Internal temperature sensor 24 privacy masking zones Internal Pan amp Tilt 6 6 6 6 6 6 6 6 6 6 6 6 6 86 reversal All in one integrated design high reliability 0 4 YS slow rotation processing without image quivering Internal Digital Camera 1 80 preset supports auto touring 4 tours 32 presets of each RS485 Optional Manchester code or coaxial monitoring control 7 alarm inputs 2 outputs normal open close switch available All metal structure high strength favorable heat dispersion Precise stepping motor drive reposeful operation sensitive reaction and exact positioning All in one integrated design compact structure easy to install Ingenious mechanical drive system support 360 continuous rotation tilt angle 0 90 and 180 All in one Digital Processing with High Sensitive and High resolution Auto Focus Digital design all data are stored in the camera block and will not be los
18. 6 ALARM SETUP 7 RETURN PRESET SETUP 1 NO 2 SET 3 CALL 4 DELETE 5 EDIT TITLE 6 RETURN EDIT TITLE 1 TITLE PRESET 001 2 RETURN 3 INPUT METHODS PINYIN ABCDEFGHIJKLMNOPQ IP High Speed Dome Camera User s Manual 8 1 Preset Setup 1 Press MENU on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Choose current preset no Move the cursor to NO Move the joystick to choose preset no from 001 220 No 1 is current preset point 3 Set current preset move cursor to Set move joystick to change the zoom times focus on the object and press OPEN to save Operation Tips The preset function is to save relative information to memories like the pan horizontal angle tilt angle and lens parameters etc Successful operation notice will be displayed on the screen 4 Call Move the cursor to CALL current preset will be appearing on the screen 5 DELETE Move the cursor to CALL current preset will be deleted 6 Edit Title Move the cursor to the EDIT TITLE and enter the menu Use keyboard to edit the title 1 Chinese Character Inputs Choose Pinyin from Input methods move the flashing cursor to the underline beneath the alphabets move the joystick left and right and move the spelling of relevant Chinese characters to the underline press OPEN on the keyboard to confirm At the moment
19. ACTIVE LAST START 6 ACTIVE OPTION 7 FAN ACTIVE TEMP READ ONLY 040 8 RETURN OPEN 000 ON IP High Speed Dome Camera User s Manual 9 3 2 Idle Time This setting allows the PTZ camera to implement an appointed action after getting into free time state for some time 1 240minutes The default setting value is 0 showing not implementing action automatically 1 make the cursor to IDLE TIME set automatic activation time ranging from 0 240 minutes IDLE TIME means the operation action after activation when idle time is set to be O the setting for IDLE ACTIVE is ineffective 2 Control joystick move cursor to IDLE ACTIVE Choose actions after activation The following options available e Default no action e Run presets e Run scanning e Run auto learning function e Run touring 3 If IDLE ACTIVE evokes presets move the joystick to ACTIVE OPTION there are 1 220 presets to chose 9 3 3 Reset Active The implementing action after PTZ switches on and self test If no manual intervention PTZ will run this action repeatedly The default value is no action 1 Move joystick and make the cursor to RESET ACTIVE choose actions after the PTZ is powered on The following options available e No action e Call presets e Run scanning Run auto learning e Run touring The state before power off 9 3 4 Fan Active TEMP read only When PTZ camera is applied in high
20. Ethernet exchanger HUB etc Pink RS485 Bae RS485 Connect to RS 485 device such as Pan Tile PTZ etc Orange Alarm in CDC12V Purple Alarm in GND Chapter 3 Parameter setup Some network parameters must be setup firstly after finishing installation includes IP address submask port etc can be setup through many kinds of ways see below two kinds for examples 1 Setup parameters such as IP address and PPPoE etc through IE browser 2 Setup parameters through applications on client s side Please be confirm PC and network camera already be connected and the network camera can be PING The Preset No 95 is to invoke the camera menu Press the left key to cancel or return to the previous menu and press the right key to confirm or access to the next menu Please refer to the camera manual for the settingd Connect to alarm input 1 channel signal alarm 0 DC12V IP High Speed Dome Camera User s Manual 3 1 Setup parameter by IE browser The default IP 192 168 0 120 default port 30001 superuser admin superuser password admin Login network camera by IE input IP address and will shoot out logging in window input username and password click login to enter IE client interface Function detailed guide please refer to NVMS Manual Important Note to check device by IE the premise is to set browser security level open IE browser enter tool Internet option security user defined level se
21. On or off The information of the camera will change while the camera block rotates and user can see the inner temperature zoom times times etc on the screen When all information displays it will be as below 288 indicates the horizontal angle and 68 indicates the vertical angle N 1 1 otice 1 If there is no any operation within 1 minute after entering the main menu it will be closed automatically 2 Default values of the items in the menu are OFF DISPLAY SETUP 1 CAMERATITLE OPEN 2 ADDRESS OPEN 3 PRESET TITLE OPEN 4 ZOOM MULTIPLE OPEN 5 COORDINATE OPEN 6 TEMPERATURE OPEN 7 DATE amp TIME OPEN 8 RETURN IP High Speed Dome Camera User s Manual ID label Camera title Hof Spaar Dora 008 ot 5 Temperature label Preset title eers and ang er LOT ie wip LUO JE 07 12 10 Date label Coordinate label NGA KOR OO Time label Lens multiple 6 Camera Parameter Setup Menu MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE E 7 EXIT 6 1 Zoom Speed 1 Press Menu on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Move the joystick vertically to Camera settings and enter the sub menu 3 Move the cursor to ZOOM SPEED Choose HIGH or LOW 4 Move the joystick vertically to RETURN E
22. al 9 1 Camera Title Dome title it is the title of the dome Assigning a name to a dome helps user to remember which dome it is 1 Press Menu on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Move the joystick down to select the System Settings then move the joystick left or right to access the sub menu 3 Move the joystick down to Camera title Operation Tips 1 Chinese Character Inputs Choose PINYIN from INPUT METHODS move the flashing cursor to the underline beneath the alphabets move the joystick left and right and move the spelling of relevant Chinese characters to the underline press OPEN on the keyboard to confirm At the moment the Chinese characters appear at the underlines above the alphabets Move the flashing cursor to the underline beneath the Chinese characters move the joystick left and right and move the relevant Chinese character to the underline press OPEN to confirm edition 2 Delete Edited Content Move the cursor to the title the title will flash Press Close to delete the characters from right to left 3 Delete Pinyin Alphabets Move the cursor to the underline beneath the alphabets press CLOSE to delete _ Notice 1 Choose preset number before the operation like deleting and editing title etc 2 Maximum 16 characters can be set for the title with input methods of
23. amera will at least record the special routing Pan 8 Tilt control or camera control demand etc for 180 seconds continuously There are 4 auto learnings maximally 1 Press MENU on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Move the cursor to USER PROGRAM Move the joystick to enter the sub menu 3 Move the cursor to AUTO LEARNING and then enter the sub menu 4 Choose number Move the cursor to NO the item that is chose will be the current auto learning and the following operation will be for it only 5 Define the record track move the cursor to RECORD TRACK and enter the menu Using the joystick to move the image or change the zoom times The camera will at least record the route for 180 seconds continuously and the stay tome zoom times and focus records will be recorded Press OPEN to save current settings and CLOSE to cancel the settings mm Execute current mode move cursor to EXECUTE the camera will run the special route continuously N Edit Title Move the cursor to the EDIT TITLE and enter the menu Use keyboard to edit the title Chinese Character Inputs Choose Pinyin from Input methods move the flashing cursor to the underline beneath the alphabets move the joystick left and right and move the spelling of relevant Chinese characters to the underline press OPEN on t
24. d Fix the fixed board fix the main body of dome on fixed board along the guide pole rotate the Dome anticlockwise tighten the screws figure8 Regulate arrowhead Main Body 1 Fix pedestal on ceiling 2 Fix the main body on pendestal along 3 guide poles A NT Knurled screw 3 CCW rotate main body at correct location 4 Tighten the knurled screw Figure8 12 3 Installation Steps taking ceiling mount as an example 1 Open the package and take out the camera and accessories 2 Drill an installation hole in the ceiling with a diameter slightly larger than 236mm 9 25 The ceiling 33 High Speed Dome Camera User s Manual material shall be considered A bracket or plate is necessary sometimes to increase support 3 Remove the ornament cover by rotating clockwise then remove the transparent cover by rotating it counterclockwise As shown in figure 9 Coding switch Sy Rotate clockwise and open the ornament cover Figure 9 4 Referring to table 2 set the camera protocol and baud rate by the coding switch as shown in figure 6 Check if the camera address is compatible with the address that you want if not set the camera to corresponding address as per table 1 5 Install the bracket components into the installation hole fasten the screws to fix the bracket clockwise rotate and fasten the transparent cover and then counterclockwise rotate the ornament cover components to install them as per figure 10
25. e hue gets warmer e BLUE GAIN Value from 0 255 bigger value indicates more blue and the hue gets colder e INDOOR The hue tends to be colder e OUTDOOR The hue tends to be warmer e SELF ADJUSTMENT The WB sensor of the camera will detect the working environment and relative parameter changes e SINGLE LOCK the WB sensor won t detect even the working environment changes IP High Speed Dome Camera User s Manual 7 Privacy Mask MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE i 7 7 EXIT This function will make concerned area masked for example the window of the bedroom or ATM in the bank The speed dome camera maximally support 24 privacy mask zones This function relates to the camera block model and the mask window numbers may differ due to different cameras Hitachi Camera maximally supporting 8 privacy zones in 360 inspecting area and 2 zones can be set maximally per screen The screen will show PLEASE MOVE once relevant area can t be masked for example when the downward horizontal angle of the lens is lt 45 SONY Camera maximally supporting 24 privacy zones in 360 inspecting area and 2 zones can be set maximally per screen Relevant area can t be masked when the downward horizontal angle of the lens is lt 45 LG and CNB cameras have no the privacy mask function 1 Press Menu on the ke
26. e bottom the lens will horizontal whirl 180 automatically and whirl 90 upwards user can watch the views on the back side so it can realize the 180 entire journey surveillance To realize the function you need set the Automatic reversal in the OSD to ON Timing Automatic Activation If the camera s not carrying out any operation by using spare time activation function the user can set auto transfer preset or start cruise self leaning or limited scan Automatic Activation By using restart the user can set automatic activation and the camera will recover to the operation before electrify after electrify or restart it also can be set auto transfer preset or start cruise self leaning or limited scan 3 3 Camera Control Magnification Times Control Through the button named Three dimension button or Wide and Tele button on the keyboard you can adjust to full view or close up view Dome camera supports digital PTZ and optics PTZ and digital PTZ can be settled Focus Control System uses auto focus as tacitly approved When lens change camera can focus on the view automatically to keep the view clear Through FAR NEAR users can adjust it manually in order to have the view you want When use the keyboard camera can be back to automatic focusing On these conditions camera can not focus automatically Target not in the centre of view Observe close view and distant view at
27. es on the camera s pin board SW1 and SW2 SW1 sets camera address and SW2 sets baud rate and protocol See Camera Settings on P38 Besides the factory protocol the camera compatible with many main protocol like PELCO D PELCO P etc Optional ALEC VCL MOLYNX VICON SANTACHI PANASONIC SAMSUNG DIAMOND KALATEL LILIN PHILIPS and AD and so on Any of the control order must be based on the address of the target camera the camera just respond to the order that has the same add of itself Three types of the address Code switch address Set by the Code switch on the bracket in the camera SW1 add Range 1 255 Broadcast address If the customer prefers to use broadcast address all of the camera in the system will carry out the same action system 255 is the broadcast address Debugging address factory protocol and PELCO protocol only if the address of the camera is O the user can control the camera by any address 3 2 Auto Carry Out the Operation Focus Rev Automatic Matching When we use manual adjustment in the case of far focus the camera high speed reaction cause the rocker shock may cause the image whisk or image lost Based on humanization design the camera 5 IP High Speed Dome Camera User s Manual automatically adjusts the rev of the tripod head according to the focus And make the manual tracking object easier Automatic Reversal If the operator pulling rocker when the lens appoint th
28. ets Each sequence can contain up to 32 presets and dwell time for each preset is independent 1 Press Menu on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Move the cursor to USER PROGRAM Move the joystick to enter the sub menu 3 Move the cursor to TOUR SETUP and then enter the sub menu 4 Tour Number Setup set the tour no within 0 4 Move the cursor to STAY TIME to edit it from 000 255 seconds 5 Tour Line Setup Move the cursor to 00 00 00 00 Move the joystick to activate the first position and then circumvolve the cap of rocker to adjust the number of preset Move the cursor to next position move again the cursor to last position The range of the presets is 1 80 each route can be setup 32 presets 6 Execute move the cursor to EXECUTE the camera will implement this function MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE i 7 7 EXIT USER PROGRAM 1 PRESET SETUP 2 TOUR SETUP 3 AUTO LEARNING 4 SCAN SETUP 5 TIMER SETUP 6 ALARM SETUP 7 RETURN AUTO LEARNING SET UP 1 NO 001 2 REC TRACK 3 EXECUTE 4 DELETE 5 EDIT TITLE 6 RETURN EDIT TITLE 1 TITLE AUTO LEARNING 001 2 RETURN 3 INPUT METHODS PINYIN ABCDEFGHIJKLMNOPQ IP High Speed Dome Camera User s Manual 8 3 Auto Learning The c
29. fferent camera blocks SANYO has 3 options OFF Control AREAS and All AREAS Without choosing backlight With choosing backlight backlighting side isd arker the image isnormal understrong sunshine 10 IP High Speed Dome Camera User s Manual 6 3 Frame Heap MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGELE j 7 EXIT 1 Press Menu on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Move the joystick and make the cursor to CAMERA SETTING enter the sub menu 3 Move the joystick and make the cursor to FRAME HEAP choose ON for enabling the slow shutter function and OFF for disabling this function 4 Move the joystick up and down to RETURN to exit the menu and save the settings Operation Tips CAMERA SETTINGS When the speed dome camera is used at night or in dark place you can setup slow shutter which can lengthen the lighting time and make the picture more clearly 1 ZOOM SPEED HIGH 2 BLC CLOSE 3 FLAME HEAP CLOSE AN 4 D ZOOM OPEN s Notice 5 VIDEO SYNC OPEN 6 B W SETTINGS 7 ADVANCED SETTINGS camera has no this function 8 RETURN 2 The flame heap can be set only in condition that the exposure mode is AUTO 3 This function may be different due to different camera blocks for
30. he keyboard to confirm At the moment the Chinese characters appear at the underlines above the alphabets Move the flashing cursor to the underline beneath the Chinese characters move the joystick left and right and move the relevant Chinese character to the underline press OPEN to confirm edition 2 Delete edited content move the cursor to the title the title will flash Press CLOSE to delete the characters from right to left 3 Delete Pinyin Alphabets move the cursor to the underline beneath the alphabets press CLOSE to delete Notice 1 Choose preset number before the operation like deleting and editing title etc 2 Maximum 16 characters can be set for the title with input methods of Pinyin numbers symbol and English etc Characters include 0 9 A Z Chinese and symbol etc 19 MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE i 7 7 EXIT USER PROGRAM 1 PRESET SETUP 2 TOUR SETUP 3 AUTO LEARNING 4 SCAN SETUP 5 TIMER SETUP 6 ALARM SETUP 7 RETURN SCAN SETUP 1 NO 001 2 PATH gt 180 3 SPEED 050 4 START POSITION 5 END POSITION 6 EXECUTE 7 DELETE 8 RETURN IP High Speed Dome Camera User s Manual 8 4 Scan Setup 1 Preset 2 points first the camera will scan between 2 presets horizontally with stable speed and same zoom time A speed dome camera has 4 groups of scans
31. liance could reach the installation height e Lifting appliance is in good safe condition IP High Speed Dome Camera User s Manual 1 Attention Electric Safety The national and local electric safety standard must be obeyed during the installation Shipping with Care Prevent the damage caused by stress strenuous vibration and moist during the shipping storing and installation The products are packed individually and will not be in warranty due to the damage caused by whole packaging in shipping Careful Installation Please refer to the instruction manual carefully Do not install the camera in opposite direction and handle the camera block with care do not press against the structural element which may cause mechanical problem The plastic cover is advanced optical product please don t touch it directly to avoid the cover scratch and bad image quality Do Not Disassembly The Camera Without Authorization Do not tear down the screws and protecting cap of the camera block There are no spare parts in the camera block for users maintenance and only the professional engineers shall check and maintain the camera Environmental Requirement Indoor Environmental Requirement Temperature 10 50 Humidity lt 90 Atmospheric Pressure 86 106Kpa AC Supply 24V 2000mA 50 60HZ Outdoor Environmental Requirement Temperature 40 60 Humidity lt 90 Atmospheric Pressure 86 106Kpa AC Suppl
32. nna 7 5 Display Settings sieve neee vens eerder eener ve a ek mean onde de 8 6 Camera Parameter Setup MENU aaa ANAN ANNA nen ada ne vaa in ee 9 Ta Privacy Maskman KABAITAN BAKA 16 8 User POG IAIN ANAN ANNA NAA AG 17 9 System SLINGS Aa AA ANA AA 23 10 Language Sep a aaa Niaan 28 11 Camera Menu IN0EX rsesssenesein seiner aandienden aaa eee eneen ende nennen 29 12 System InStallaBON causerzersnerrasteande ra anaacnen den deave AANGAT AGAIN 30 Appendix A 24VAC Wire Diameter and Transmission Distance Comparison Chatt 36 Appendix B Wire Gauge Conversion Charina 37 Appendix C Lightning Proof and Surge Signal Proof ns snas anas sana anananansanennenananensennenanseneensnenananennernnns 38 IP High Speed Dome Camera User s Manual SAFE PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT OPEN COVERS NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The requirement for the people who will install and repair the machine Owning the certificate to install and repair CCTV system Owning the certificate to work aloft Obtaining the basic knowledge and operating skill of wiring and connection at low voltage e Reading carefully and understanding all the contents in this manual The requirement for lifting appliance e Using the lifting appliance suitable for the speed dome camera installation place and installation types e Lifting app
33. ntal origin which was default setting when leaving factory then move vertically to vertical origin lens is pulled closest and farthest self check finished Edition number 1 0 0 Protocol PELCOD Baud rate 9600 Camera ID 001 This information will be shown until finishing self test for system Edition number Shows information of camera software edition Protocol Shows type of control protocol which has been set up Baud rate Shows communication baud rate which has been set up including 2400 4800 9600 19200 four types of communication baud rate Detailed setting method as per addenda Camera ID Set via camera s switch SW1 detailed setting method as per addenda 4 2 Transfer Main Menu Open the main menu of system by pressing menu key on the control keyboard or by matrix via the operation Call No 95 or 64 preset positions All menu setup must first transfer main menu 4 3 Basic Operation of Menu and Keyboard Basic Operation of Keyboard OPEN When choosing image shows increasing iris it will save automatically after finishing setup CLOSE When choosing image shows decreasing iris it will save automatically after finishing setup T IP High Speed Dome Camera User s Manual NEAR focus on vicinity FAR focus on beyond Joystick tilt up When choosing menu shows choosing the previous one when choosing image shows camera circumgyrating upwards Joystick tilt down When choosing menu show
34. rightness and CCD light sensitiveness etc On the condition that the exposure is definite AE the camera will automatically decide the Al AL the camera will automatically decide the AE speed BRIGHTNESS control the image brightness Notice All functions in Advanced Settings depend on the camera block and its parameters 14 MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE i 7 7 EXIT CAMERA SETTINGS 1 ZOOM SPEED HIGH 2 BLC CLOSE 3 FLAME HEAP CLOSE 4 D ZOOM OPEN 5 VIDEO SYNC OPEN 6 B W SETTINGS 7 ADVANCED SETTINGS 8 RETURN ADVANCED SETTINGS 1 EXPOSURE AUTO 2 AE 1 50 3 Al F1 4 4 BRIGHTNESS F1 410DB 5 WB AUTO 6 RED GAIN 7 BLUE GAIN 8 RETURN IP High Speed Dome Camera User s Manual 6 7 2 WB Mode The system has the following WB modes Auto Manu Self adjustment Single lock Indoor Outdoor etc See detailed operation steps as below 1 Enter the main menu 2 Move the joystick and make the cursor to Advanced Settings Enter the sub menu and chose WB mode The setup will be saved when exiting the menu AUTO is the default mode the WB sensor of the camera will detect the environment and enable the color reproduction If you choose MANU mode the RED GAIN and BLUE GAIN value can be set e RED GAIN value from 0 255 bigger value indicates more red and th
35. s choosing the next one when choosing image shows camera circumgyrating downwards Joystick pan left When choosing menu shows entering junior menu or entering setting up or return to superior menu when choosing serial number shows decreasing when choosing image shows camera circumgyrating leftwards Joystick pan right When choosing menu shows entering junior menu or entering setting up or return to superior menu when choosing serial number when choosing serial number shows increasing when choosing image shows camera circumgyrating rightwards Three Dimensional Joystick Circumgyrating Joystick Cap Function Circumgyrating deasil shows pull image closer setting date time visitatorial data increased circumgyrating widdershins shows pull image farer setting date time visitatorial data decreased Basic Menu Operation Return return to superior menu Open open certain setting Close close certain setting 4 4 Camera Language Setting Switch Chinese English in language setting menu under main menu 5 Display Settings MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGES 7 7 EXIT 1 Press Menu on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Move the joystick horizontally to enter CAMERA SETTINGS 3 Each item in the menu can be set to
36. t also support change frame ratio while setting up video image quality it s able to restrict compression bit rate of video image gt D1 PAL 704 576 NTSC 704 480 CIF PAL 3527288 NTSC 352 240 QCIF PAL 176 144 NTSC 240 160 supported gt OSD supported date and time setup available Remote interview and transmission function gt One self compliant 10M 100M Ethernet interface as standard accessory gt PPPoE DHCP DDNS protocol supported gt Available to set parameter browse real time video check network camera state through applications or IE browser Available to realize alarm link and save compressed bit rate through network gt Available to realize remote upgrade and maintenance through network gt RS 485 can support one way network rendezvous point aisle connection client side can control serial devices through network rendezvous point aisle of network camera 1 2 Applications Suitable for circumstances required for network remote surveillance gt ATM Bank Counter Supermarket Factory etc gt Nursing House Kindergarten School etc gt Intelligentized door management system gt Intelligentized Building intelligentized community management system gt Electricity station telecom base station etc unmanned on duty system gt Outdoor bridge tunnel crossing traffic etc surveillance system gt flowing line and warehouse surveillance gt 24h surveillance to road traffic gt Remote surveillance to forest foun
37. t even power down IP High Speed Dome Camera User s Manual Auto Brightness Control Auto Iris Auto AWB Color amp B W Transition Auto BLC Auto Frame Accumulating OSD Menu Chinese English Menu OSD menu display change the information and parameter of the camera by keyboard and OSD operation becomes simple and easy Auto activation function can be set evoking presets or starting up tours auto leaning and horizontal scan can be set when the camera is not in use Restoring operation before power down or carry out appointed operation Internal Temperature Detector Real time temperature display Fans start up when the temperature exceeds the upper limit Speed dome will postpone starting up when the temperature is lower than the lower limit The fans start up according to real time temperature detection which makes the fans longevity longer Real Time Clock Function Real time display clock can be set Real time color amp B W transforming time Alarm time can be set 3 Function and Operation This chapter describes the main function and the realize principle of the speed dome and does not involved in operation Different system has different method of operation Usually we use the operation manual from the system company If you have any special requirements please contact the system company to get the necessary information 3 1 Set the Camera Coding There are two code switch
38. t security level security level low or directly set ActiveX Widget and Insert to open Appendix Parameter Description Video out 1 BNC PAL NTSC 1 0Vp p 750 Video Compression H 264 ISO IEC 14496 10 baseline profile to level 3 1 PAL D1 704x576 25fps CIF 352x288 25fps QCIF 176x144 25fps NTSC D1 704x480 30fps CIF 352x240 30fps QCIF 240x160 30fps Bit stream Control CBR VBR Image Frame Rate 1 internal Microphone In 1 External Microphone In 1 Audio Line Out Audio Compression G723 1 6 3kbps Audio bit stream 6 3Kbps Audio Input Output Web Server Microsoft Internet Explorer Version 5 5 or higher RTP RTCP TCP UDP HTTP DHCP DNS IPv4 IPv6 SMTP FTP Network Ethernet RJ 45 10 100Base T Network Protocol Alarm Input Output 1 Alarm Input PTZ Control RS485 Polco D Polco P SD Card Support MicroSD HC MiniSD HC Safely Watchdog Password protection Protection IP66 Standard Vandal Proof CMS Client and SDK Open API for application integration including SDK The next content is high speed dome camera manual for the settingd IP High Speed Dome Camera User s Manual Contents LANAO NAA aanne dra aans AA AA a naaa sag 3 2 Speed dome camera performance Characteristics un anas sans ennansnsnneanenanunensannenanasensannenenanenenneenenananensennns 4 3 Function and OperaHOn nananana eeen ann aaneen man venen 5 4 Basic Operation of Dome Camera kaaa i
39. tain and river etc Chapter 2 Installation 2 1 cautions gt Please check carefully while unpacking be sure articles inside accordance to the list gt Please read this chapter carefully before installation gt Be sure to off all concerned power while installation gt Check power and voltage in case to damage facility because of unmatched voltage gt Installation circumstance do not install in circumstances of high humidity or high temperature please keep good ventilation pay attention to defend rain avoid installing in acute vibrate circumstance gt In times of malfunction do not attempt to dismantle and service the camera yourself Please refer to qualified serving personnel to repair or contact our technical department to solve the problems Remark power supply lens and SD card optional while ex factory IP High Speed Dome Camera User s Manual 2 2 Panel Illuminate 2 2 1 Rear Elevation Fig 2 1 Connection Cable ID Cable Function Connection Red White 1 Black Purple AC24V Input Please refer to the camera parameter 2 N A Video Output Connect to video cable of monitor standard BNC interface 3 5mm interface connect to acoustics device such as speaker etc for audio speech output impedance gt 160 connect to audio input device such as tone arm impedance 1kQ 123 3 N A Audio In Output Video output en Video input GND 4 N A Network interface Connect to Ethernet device such as
40. talled inside 45 range Earthing resistance Na must not greater than 4 Ohm Protective Tube 38
41. temperature its own temperature will increase In order to keep the whole stability of PTZ the fan will turn on after the temperature rises to some degree 1 Move joystick and make the cursor to Fan active Temp Users can set temperature according to actual situation The default startup temperature of the fan is 40 C the user can enter fan startup set menu and adjust fan startup temperature As shown in the chart the temperature ranges from 0 to 60 C Zu IP High Speed Dome Camera User s Manual MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGENE 7 EXIT SYSTEM SETTINGS 1 CAMERA TITLE 2 INFORMATION 3 PAN amp TILT 4 DELETE 5 DEFAULT 6 RESET 7 VIDEO SIGNAL PAL 8 DATE amp TIME 9 RETURN DELETE 1 ALL PRESETS 2 ALL TOUR 3 ALL AUTO LEARNING 4 ALL SCAN 5 ALL MASK 6 ALL TIMER 7 ALL ALARM 8 RETURN SYSTEM SETTINGS 1 CAMERATITLE 2 INFORMATION 3 PAN amp TILT 4 DELETE 5 DEFAULT 6 RESET 7 VIDEO SIGNAL PAL 8 DATE amp TIME 9 RETURN SYSTEM SETTINGS 1 CAMERA TITLE 2 INFORMATION 3 PAN amp TILT 4 DELETE 5 DEFAULT 6 RESET 7 VIDEO SIGNAL PAL 8 DATE amp TIME 9 RETURN 9 4 Delete 1 Press Menu on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Mo
42. the Chinese characters appear at the underlines above the alphabets Move the flashing cursor to the underline beneath the Chinese characters move the joystick left and right and move the relevant Chinese character to the underline press OPEN to confirm edition 2 Delete edited content move the cursor to the title the title will flash Press CLOSE to delete the characters from right to left 3 Delete Pinyin alphabets move the cursor to the underline beneath the alphabets press Close to delete Notice 1 Choose preset number before the operation like deleting and editing title etc 2 Maximum 16 characters can be set for the title with input methods of Pinyin numbers symbol and English etc Characters include 0 9 A Z Chinese and symbol etc 17 MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE i 7 7 EXIT USER PROGRAM 1 PRESET SETUP 2 TOUR SETUP 3 AUTO LEARNING 4 SCAN SETUP 5 TIMER SETUP 6 ALARM SETUP 7 RETURN TOUR SETUP 1 NO 2 STAY TIME 001 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 3 EXECUTE 4 RETURN IP High Speed Dome Camera User s Manual 8 2 Tour Setup Auto Tour is defined as a sequential moving from preset to preset and dwell for a specific time at each preset It is useful if you need to repeat switching among a number of pres
43. the menu 3 Move the joystick and make the cursor to B amp W SETTING and enter the next menu 4 Make the cursor to B amp W SETTING move the joystick to choose switch modes There are 4 modes available AUTO TINING B amp W and COLOR AUTO is the default mode e AUTO e TINGING Setup the time for Color amp B W switch and the time setting is effective only in Color amp B W automatically switches according to illumination timing mode e COLOR Color mode setup e B amp W B amp W mode setup 5 Move the joystick vertically to return and exit the menu Operation Tips Color B amp W auto switch ensures the image quality and save storage space Notice 1 This function relates to the camera block model and parameter If the camera block has no this function the Color B amp W auto switch option is ineffective 2 Clockwise rotate the tridimensional rocker cap the time value will be bigger otherwise the time value will be smaller 3 Only TIMING is chosen for B amp W SETTING the timing setup is effective 13 B amp W SETTINGS 1 B amp W SWITCH AUTO 2 B amp W SWITCH 00 00 3 COLOR SCHEDULE 00 00 4 RETURN MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE 7 7 EXIT CAMERA SETTINGS 1 200M SPEED HIGH 2 BLC CLOSE 3 FLAME HEAP CLOSE 4 D ZOOM OPEN 5 VIDEO SYNC OPEN 6 B W SETTINGS 7 ADVANCED
44. the same time cannot guarantee both of them are clear Target is as high light materials Such as neon lamp spotlight and any shine objects Target moves so fast Big size dull target such as wall Target is too dark or not clear Target view is too small Iris Control System uses auto Iris as tacitly approved It can feel the light around to adjust the iris to keep the output view s luminosity steady Users can use Open Close button on the keyboard adjust the iris manually to get the fittest luminosity It can be back to automatic iris by using the keyboard Face Away from Light Compensating Camera district fulfill facing away from light compensating automatically Under high light background it will automatically compensate to the light and adjust the light to the fittest view This method can avoid whole view with more light and make the target view more clearly Auto White Balance Automatic adjust based on the changing of light around to appear the true color 3 4 Monitor Function Set adjust preset point Preset point function is that record the data of horizontal angle tilt angle and focal distance of camera to 6 IP High Speed Dome Camera User s Manual the memory When need you can use these data to the position Preset point can be set quickly and easily by using keyboard you can set two hundred twenty preset points Auto Cruising Auto cruising is the function of this dome It can be set
45. tled previously make the preset points as a sequence added to the auto cruising You can inset preset point to the cruising can fulfill auto cruising between preset points Cruising sequence can be set You also can set the stop time of preset point one cruising can be set 32 preset points Level Right amp Left Scan Through keyboard and menu users can set left position and right position as a speed scan from left to right Self learning This dome has the pattern scan function The dome can record at least 180s moving track Run the self learning pattern according to the record dome can repeat moving one dome can set 4 routes Privacy masking function set Users can set privacy masking function to cover some zone Alarm input amp output control When dome receive a alarm signal run the preset action until the alarm is finished If have some unusual situation it will send another alarm signal Dome can set 7 input alarm signals 2 output signals Camera Lens Position Display After dome self check the position will at 0 of level and vertical place the level place from 0 360 the vertical place from 0 90 The information can be displayed on the screen 4 Basic Operation of Dome Camera 4 1 Camera Power On Self Test After connecting wires and power on dome camera executes self checking program it will appear system information on the screen as shown below Camera will move horizontally to horizo
46. ve Settings Move the cursor to Active Settings select the item to access its submenu e NO Edit the number of alarm input channel 001 007 When there are two alarm inputs number 001 and number 002 at the same time the dome will respond to number 001 first e ALARM LINKAGE Set auto respond function OFF Auto Panning Pattern Preset Cruise Call preset For example Alarm channel 001 call preset 1 alarm channel 002 call preset 2 ALARM ACTION Select respond output channel for current alarm input OFF 1 2 1 amp 2 e ALARM OUTPUT Alarm outputs options while there is alarm input Null no Alarm output alarm output 1 alarm output 2 both 8 6 2 Placement Set Move joystick and make the cursor to Placement set and enter the placement set menu there are 2 modes ON Enable this function OFF Disable this function START END TIME Set the start end time period for alarm If the placement state is On START END TIME must be set to make the alarm action effective 499 9 System Settings MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE E 7 7 EXIT SYSTEM SETTINGS 1 CAMERA TITLE 2 INFORMATION 3 PAN amp TILT 4 DELETE 5 DEFAULT 6 RESET 7 VIDEO SIGNAL PAL 8 DATE amp TIME 9 RETURN EDIT TITLE 1 TITLE 2 RETURN 3 INPUT METHODS PINYIN ABCDEFGHIJKLMNOPQ IP High Speed Dome Camera User s Manu
47. ve the cursor to SYSTEM SETTINGS and enter the menu 3 Move the cursor to DELETE and then enter the sub menu e ALL PRESET e ALL TOUR e ALL AUTO LEARNING e ALL SCAN e ALL MASK e ALL TIMER e ALL ALARM Implementing the function DELETES OPERATION will make camera s parameters and system s parameters default value delete all privacy window and alarm setting Please use with caution 4 Take deleting ALL PRESET as example to explain the operating process Move joystick and make the cursor to ALL PRESET and then move the joystick to enter the deletion interface press open all presets will be deleted Note Once the instruction of deleting is implemented it can t be recovered Please operate this function with caution 9 5 Default 1 Press MENU on the keyboard or evoke the presets no 95 and 64 to enter the main menu 2 Move joystick and make the cursor to SYSTEM SETTINGS and enter the sub menu 3 Move the cursor to DEFAULT and enter the reset interface Press OPEN to implement DEFAULT function press CLOSE to cancel the operation 9 6 Restart 1 Choose RESET from SYSTEM SETTING Move joystick to left or right and then PTZ will restart to execute the self test 27 MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE i 7 7 EXIT SYSTEM SETTINGS 1 CAMERA TITLE 2
48. xit the menu and the system will save the settings automatically CAMERA SETTINGS 1 200M SPEED HIGH 2 BLC CLOSE 3 FLAME HEAP OPEN 4 D ZOOM OPEN 5 VIDEO SYNC OPEN 6 B W SETTINGS 7 ADVANCED SETTINGS 8 RETURN IP High Speed Dome Camera User s Manual 6 2 BLC 1 Press Menu on the keyboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE i j 7 EXIT 2 Make the cursor to CAMERA SETTINGS and enter the sub menu 3 Move the joystick and make the cursor to BLC move the joystick and choose BLC ON or OFF 4 Move the joystick vertically to RETURN Exit the menu and the system will save the settings automatically Operation Tips GAMERABEDINGS Strong backlight makes objects cast shadows BLC function makes the 1 ZOOM SPEED HIGH speed dome camera adjust aperture to fit the lights changing and 2 BLC CLOSE calibrate image brightness to make the image clearer 3 FLAME HEAP CLOSE A 4 D ZOOM OPEN Z notice 5 VIDEO SYNC OPEN 6 B W SETTINGS 1 This function relates to the camera block model and parameters 7 ADVANCED SETTINGS While enabling BLC it will adjust automatically Choosing ON 8 RETURN 2 BLC can be set only while exposure mode is AUTO 3 BLC may be different due to di
49. y 24V 2500mA 50 60HZ Do Not Aim Objects in Strong Light Do not aim the objects in strong light or the sun to avoid the image blur and spectacle no matter the camera is in use or not Waterproof The outdoor speed dome cameras are featured as waterproof damp proof and dustproof and could meet the international standard IP66 The indoor speed dome camera can not be installed at the place where there is full of hydrosphere and water The water drops and splashing may damage the inside components of both the indoor and outdoor cameras IP High Speed Dome Camera User s Manual 2 Speed dome camera performance characteristics 2 1 Technical Parameter Electrical Set up a Baud rate Rating Voltage AC24V RS485 2400 4800 9600 19200bps Power 12W indoor 35W outdoor Protocol Pelco P Pelco D Phillips Panasonic and so on 17 Protocol choice Operation Add Set up 0 255 Decoder Internal Environment Panning angle 360 Continuous rotation Operation 40 60 C Environment Tilt angle 0 90 Humidity 0 95 No condensation IP66 24 hour safety cover 0 Rotary speed ON Sasi oo TVS1500W lightning proof f surge proof Alarm 7 input 2 output Physical Preset 220 Installation Ceiling Corner wall type Surveillance way Preset touring horizontal scan Auto Weight without 4 25Kg outdoor 3 85Kg indoor learning bracket Speed Magnification times match with Material AML speed
50. yboard or evoke the presets no 95 and 64 to enter the main menu or press the preset no 1 twice continuously within 1 second 2 Move cursor to PRIVACY MASK and enter the menu MASK NO Choose the mask no as the privacy mask area MASK AREA Define the current privacy mask window PRIVACY MASK 1 MASK NO ACTIVE Enable disable the privacy area ON Enable current privacy mask area a la an DE OFF disable current privacy mask area 4 DELETE DELETE Delete current privacy area settings 3 Define current privacy mask window choose the window no and then operate as follows a Make the cursor to PRIVACY AREA and enter the menu Move the joystick and make the privacy area displayed on the screen b Press OPEN privacy area can be set move the joystick downward upward rightward 5 RETURN leftward the privacy area will be higher shorter wider narrower c Press OPEN to save current privacy mask settings and the window status will be open automatically A Notice This function relates to the camera block and its parameters This option will be ineffective if the camera has no this function ORB BO NAK 16 8 User Program MAIN MENU 1 DISPLAY SETTINGS 2 CAMERA SETTINGS 3 PRIVACY MASK 4 USER PROGRAM 5 SYSTEM SETTINGS 6 LANGUAGE i 7 7 EXIT USER PROGRAM 1 PRESET SETUP 2 TOUR SETUP 3 AUTO LEARNING 4 SCAN SETUP 5 TIMER SETUP
Download Pdf Manuals
Related Search