Hand Dryer Installation & User Manual - Vent-Axia
Contents
1. 15mA type rated operating current e Do not let children hang from the hand dryer e Wear gloves when inspecting and cleaning the unit e Do not use the hand dryer in the following places Where the ambient temperature is below 10 C or above 40 C Where the hand dryer may come into direct contact with water Where the unit is under direct or strong sunlight Where condensation may form within the unit Features No touch hand drying ensures complete hygiene Economical high speed drying only 10 seconds Built in tamper proof timer function Fitted with Anti bacterial dust filter 2 speed amp 2 heat settings Anti bacterial coating Specifications Rated voltage 220 240V Motor Brushless Dc motor Input power 1650 2050W Induction method IR blocking Air velocity 95 M S Protection class Heating power 1000 1200W Dimensions 300x220x685 Hand dryer Features amp functions Power supply heating button speed button Cover Drying time and fault display Power indicator Self check indicator Hand drying area Power switch Sensor Drain hose Air filter Drain tank Unit Hand dryer dimensions Terminal Box location D 5 2 101 Installation Panel 685 623 Power Cord hose rear Terminal Box location Drain Tank Air Filter Before installing the hand dryer Installation location Install the hand dryer in a location where it will be easy to use and ensure that t2. Hand Dryer Installation amp User Manual Please read instruction in conjunction with the illustrations Please save these instructions Safety amp Guidance notes Important Read all these instructions before commencing the installation e All wiring of this hand dryer should be in accordance with the current IEE regulations or the appropriate standards in your country e This hand dryer MUST be installed by a suitably qualified person e Ensure that the mains supply voltage frequency and phase complies with the hand dryers rating label e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Do not open the front panel once installed Do not allow hand dryer to get excessively wet Do not modify and disassemble the unit unnecessarily The hand dryer should be provided with a fused spur isolator switch capable of disconnecting all poles having a contact separation of at least 3mm Ensure the hand dryer is properly earthed e Always use the hand dryer with the drain tank amp air filter provided e Werecommend installing a RCD residual current device use a single phase 220 240V 50Hz cable with a 20A rated current
3. d with a length of flexible Cord for connecting to a suitably rated fused spur if required Attach the installation panel to the wall Using the 6 screws provided 81 5 installation screws If the wall is concrete use A Commercially available metal screw wien S Plugs panel Make sure that the wall the hand Dryer is being fixed to is strong enough to Take the weight of the dryer 10 5kg Remove the drain tank G To gain access to the drain tank Cover screws 10 3 installation hole details unit mm Cover retaining clips x 3 To remove the front panel remove the 2 screws and retain Carefully unclip the 3 cover retaining clips located at the top of the hand dryer cover front panel Do not force the cover off installation Screw front panel terminal box cover lock clutch hole terminal box Remove the terminal box cover To gain access to the hand dryer wiring terminal block Pull the power cord through the back of the unit as shown Attach the hand dryer to the wall plate By hooking it onto the 2 upper hooks amp 1 lower hook Secure to the wall plate at the bottom With the safety screw provided this screw is temporarily fixed on the unit Power socket JW Power cord Note the installation screw for the unit will not tighten completely if the hooks at the bottom of the installation panel are not in place Ensure the lower hook is completely h
4. here is adequate space around the dryer for cleaning and maintenance If the unit is installed too low water may splash onto the dryer when the floor is being cleaned The bottom of the hand dryer must be mounted at least 150mm above the floor The left hand side of the hand dryer must be at least 150mm away from any walls to allow access to the power switch speed amp heat setting switches We recommend that the right hand side of the dryer should be at least 100mm from any wall objects Avoid installing the hand dryer in locations where people or doors might bump into the dryer e Choose a completely flat surface on the wall to install the dryer Power indicator Self check indicator Power supply Installed terminal box Fixed screws Installation panel Power switch Distance between the terminal box without Installation heights cover and the ground Recommended 890 mm for man 870 mm for woman Front panel installation screws Installation procedure Use 220 240V 50Hz supply Do not use if power supply is exceeding rated voltage 10 Use a power cord that is between 2mm and 2 5mm A drop in voltage is possible if the power cord run exceeds 11m in length so we recommend using 2 5mm cord Power cords with ground line Wire the unit Fit a suitable recessed back box And run the cable through as shown Note The unit is supplie
5. l the indicators go off and then turn the dryer back on If the indicator still lights up or flashes turn off the unit Isolate the dryer from the mains supply and contact a service engineer Routine Cleaning amp Maintenance of the hand dryer Warning The Hand dryer must be isolated from the power AN supply before any cleaning and maintenance takes place Cleaning the body of the hand dryer e Clean the unit with a soft cloth e fthe unit gets very dirty clean with a soft damp cloth with a neutral cleaning agent then clean with a dry soft cloth e Remove any dirt from the sensor area e Only use a neutral cleaning agent e Do not use thinners acidic or alkaline toilet cleaners or any type of brushes use of these may damage the surface of the hand dryer e If chemical cloths are to be used please read their instructions first AN Caution always wear suitable gloves when cleaning Draining and cleaning the drain tank Before the tank fills up at least once a week e The water blown off the hands when drying is called drain water e Empty the drain water at any time in order to prevent accumulated water from exceeding the full level e The water in the tank may start smelling if it remains in the tank for too long Pull the drain tank out in a horizontal direction as indicated This ensures the drain water does not spill out Drain tank Open the drain tank cover and empty out the water Wash out the interi
6. l the indicators in the and is flashing display area have gone off takes around 40 seconds then turn on the power switch again If the above actions do not work turn off the power supply isolate the dryer them call a service engineer Supplied by APL 44174417D 0914 10
7. ooked on to the s rear of the unit P n The safety screw must be fitted to Safety screw avoid the dryer being knocked off the wall Installation panel Strip back the mains cable And connect to the terminal block i unscrew here Ensure all connections are N to change fuse_7 Secure gt se earth wire Using the p clip provided Secure the mains cable in position Replace the terminal box cover ensuring that the wires do not get pinched z pelts Note The front panel cannot be Re attached if there are any Wires in front of the terminal box cover Move the wires to the right if this applies power cord Attach the front panel Carefully insert the 3 cover clips into the top of the cover front panel Replace the 2 cover screws at the bottom of the dryer Re attach the drain tank installation screw Make sure that the air filter is all the way in drain tank Turn on power and check the dryer operates correctly Using the hand dryer e Shake off excess water at the sink And insert both hands into the dryer The unit starts to run automatically e Pull your hands out slowly letting the air blow the water off e Pull your hands out completely repeat process until dry Self check indicator When a malfunction or error occurs the self check indicator located on the top of the dryer check will either light up or flash Turn off the power switch wait about 40 seconds until al
8. or of the drain tank Replace the drain tank cover and re attach it to the dryer Ensure that the drain tank is correctly inserted At regular intervals at least once a week carefully pour 200cc around a cup of water through the drain hole to prevent it from getting clogged up b gt drain hole af Cleaning the air filter At least once a week Remove the air filter Pull the air filter out by the handle shown Handle Cleaning the air filter Use a vacuum cleaner to remove any dirt from the filter Air filter If the filter is very dirty wash it carefully in cold or warm water Allow the filter to dry and replace Make sure that the air filter is all the way in If it is not located correctly dirt or dust will enter the dryer and shorten its service life Hand dryer troubleshooting If the following problems occur please perform checks as follows No air blows even if hands Do any of the display Turn the circuit breaker on are inserted indicators light up Is the power switch on Turn the power switch on Are you putting your hands in Put hands in all the way all the way The unit does not stop Is the sensor being blocked Turn the power switch off and blowing by dust or dirt then after all the lamps in the display have gone off clean the sensor Indicator light is flashing If the power supply problems Turn the power switch off occur the indicator lights up Check al
Download Pdf Manuals
Related Search