Vehicle Programming Instructions
Contents
1. Page 5 of 16 Form0141C 03 29 2007 Superchips Inc 1 Connecting the MAX Micro Tuner to your vehicle With the ignition switch in the OFF position locate the diagnostic connector under the dash to the right of the steering wheel and connect the MAX Micro Tuner cable to the diagnostic connector See Figure 5 When connected the MAX Micro Tuner will run a self test displaying several start up messages Following the start up messages if the MAX Micro Tuner has been previously used to program a vehicle the Micro Tuner will beep and display Micro Tuner is VIN Locked This indicates the MAX Micro Tuner has been previously used to program a vehicle and can not d Figure 5 program another The MAX Micro Tuner will A continue to operate normally on the original vehicle and may be used as a DTC Reader on other Ford vehicles The MAX Micro Tuner then displays the following message Begin with Ign OFF Press gt 2 Selecting Tune Vehicle Diagnostics Turn the ignition switch to the ON position Press the gt key on the keypad The MAX Micro Tuner will beep and display the message A Tune Vehicle B Diagnostics Press the A key on the keypad to continue with the tuning process Press the B key to read and or clear any Diagnostic Trouble Codes from the vehicle See DTC Reader Instructions and DTC interpretation in the separate manual provided for this purpose with your product 3 Vehicle Programming2. 585 7000 http www Superchips com Superchip amp Superchips are registered trademarks of Superchips Inc Page 7 of 16 Form0141C 03 29 2007 Superchips Inc Page 8 of 16 Form0141C 03 29 2007 Superchips Inc The MAX Micro Tuner is testing to see if the Passive Anti Theft System PATS is active If PATS is active the MAX Micro Tuner will beep and display the message Resetting PATS Please Wait After accessing the vehicle s computer if PATS is not active the MAX Micro Tuner automatically clears the vehicle DTCs The MAX Micro Tuner Beeps and displays the following messages Clearing DTCs Please Wait The MAX Micro Tuner will beep and display the message Stock Saved Press gt IMPORTANT NOTE You MUST remove the fuel pump fuse from the vehicle fuse block before attempting to install a Performance Program or to return the vehicle to its STOCK condition Failing to do so may cause serious damage to your engine 5 Installing the Superchips Performance Program The MAX Micro Tuner allows for two different levels of performance tuning Selecting the Tuning Level Setting The PERFORMANCE tuning level provides the most aggressive performance gain Use of premium fuel 91 octane or greater is required to realize these gains Caution The Performance tuning level requires that you use at least 91 octane fuel Using a lower octane fuel while the Performance tuning level is selected may cause detona
3. Press the A key on the keypad The MAX Micro Tuner will beep and display the message Is FUEL PMP Fuse Removed YES NO If NO is pressed the MAX Micro Tuner will beep and display the following messages MUST Remove Fuse Before Tuning Press Any Key To Continue After pressing a key the MAX Micro Tuner beeps and returns to Selecting Tune Vehicle Diagnostics at Step 2 If YES is pressed the MAX Micro Tuner will display the following message Turn Ignition ON Do NOT START Eng Superchips Inc 1790 East Airport Blvd Sanford FL 32773 407 585 7000 _http www Superchips com Superchip amp Superchips are registered trademarks of Superchips Inc Page 6 of 16 Form0141C 03 29 2007 Superchips Inc Turn the ignition to the ON position The MAX Micro Tuner will proceed to establish communications and display the following message Establishing Communications The MAX Micro Tuner is establishing communications with and identifying the vehicle s computer If the MAX Micro Tuner has not yet been used to program a vehicle no vehicle ID will be stored in the MAX Micro Tuner In such a case the MAX Micro Tuner will begin saving the STOCK program for the vehicle If the vehicle ID matches a vehicle ID stored in the Micro Tuner the MAX Micro Tuner will go directly to the Return to Stock Sequence at Step 10 that follows Not the Original Vehicle Program Error Type 09 Call Superchips Press g
4. Turn the ignition to the ON position The MAX Micro Tuner will beep and display the following messages Ready to RETURN to STOCK The Ignition SW Must remain ON Press gt to Continue Press gt The MAX Micro Tuner will beep once and erase the present program The MAX Micro Tuner will blink the following message Erasing Present Program After the program has been erased the MAX Micro Tuner will blink the following message Return To STOCK The bottom line of the display shows the programming progress When the programming sequence is completed the MAX Micro Tuner beeps and will display Please Wait The MAX Micro Tuner is testing to see if the Passive Anti Theft System is active If PATS is active the MAX Micro Tuner beeps and displays the message Resetting PATS Please Wait If Returning to Stock and PATS is not active the MAX Micro Tuner automatically clears the vehicle DTCs The MAX Micro Tuner Beeps and displays the following messages Clearing DTCs Please Wait TUNING Installed Turn Ign OFF Remove the Ford MAX Tuner Re install the FUEL PUMP Fuse Turn the ignition OFF remove the MAX Micro Tuner cable and re install the Fuel Pump Fuse Superchips Inc 1790 East Airport Blvd Sanford FL 32773 407 585 7000 _http www Superchips com Superchip amp Superchips are registered trademarks of Superchips Inc Page 14 of 16 Form0141C 03 29 2007 Superchips Inc No Start a
5. Centers If you need to return your vehicle to a service center restore the vehicle program to its STOCK program as described below The service center might reprogram your vehicle with an updated STOCK program without your knowledge If your vehicle has not been returned to its STOCK program prior to service the Superchips MAX Micro Tuner will no longer be able to program your vehicle Such a failure is not covered by the Superchips Inc warranty Vehicle Preparation Before connecting the MAX Micro Tuner to your vehicle make sure that all power draining accessories are turned off Radio lights cell phones etc all need to be turned off as the MAX Micro Tuner needs full battery voltage to program Ensure your vehicle battery is fully charged and not connected to a battery charger Do not leave the MAX Micro Tuner connected and unattended for any length of time to prevent unnecessary battery drain Do not remove the programming cable during any programming sequence Important Note Regarding Storage of Your MAX Micro Tuner It is recommended that you not store your MAX Micro Tuner in your vehicle if ambient temperatures in your area fall below 32 F Excessively low temperatures can cause malfunction or damage to the MAX Micro Tuner that is not covered by the Superchips Inc warranty Superchips Inc 1790 East Airport Blvd Sanford FL 32773 407 585 7000 _http www Superchips com Superchip amp Superchips are registered trademarks of
6. Manual Trans YES NO Press YES if the vehicle has a Manual Transmission Shift Points and Shift Pressures are not options on Manual Transmission vehicles Press NO if the vehicle has an Automatic Transmission Editing the Gear Size Option Setting Note The Gear Size Option is not supported for all vehicles The Gear Size Option allows the MAX Tuner to match the transmission Shift Points to the selected Gear Size It also corrects the Speedometer Odometer when other than STOCK Gears are installed The Gear Size Option allows you to set the Gear Size to STOCK or one of the following options 3 08 3 27 3 55 3 73 3 90 4 10 4 30 4 56 Note Speedometer Odometer correction is valid only for Mustangs amp Marauders equipped with electronic soeedometers The MAX Micro Tuner will beep and display the message Set GEAR Size XXX xxx is Stock or the Gear Size The present Gear Size setting flashes Use lt or gt to change the Gear Size setting and YES to save the Gear Size Custom Option setting Pressing lt key when the lowest gear ratio is displayed will select the STOCK gear setting 7 Editing the Custom Options Settings The MAX Micro Tuner will beep and display the keys to use while editing the Custom Option settings Adjust lt or gt then Press Any Key Save YES to Continue Pressing lt and gt on the keypad adjusts the Custom Option setting Pressing YES on
7. You Get Service If something goes wrong with your Product during the warranty period use the following procedure to return the Product to Superchips 1 Call Superchips Customer Service at 1 888 227 2447 Monday through Friday from 8 00 am to 5 00 pm EST to request a Return Authorization RA number 2 Mark the outside of the shipping package with the RA number Packages that are not marked with the RA number will be refused 3 Make a copy of your sales receipt The sales receipt must be from the location where you purchased your Product and must include the name of the business where you purchased the Product and the address of such business Invoices credit card statements or sales receipts from an online payment service company will not be accepted 4 Send the Product postage paid the copy of the sales receipt a brief written description of the problem and your contact information to Superchips Inc 1790 East Airport Blvd Sanford FL 32773 Attn Warranty Claims We will inspect the Product and either repair it or replace it with a new or rebuilt Product We reserve the right to use refurbished parts when making repairs Your Rights Under State Law This warranty gives you specific legal rights and you may also have other rights which vary from state to state Superchips Inc 1790 East Airport Blvd Sanford FL 32773 407 585 7000 _http www Superchips com Superchip amp Superchips are registered trademarks of S
8. FL 32773 407 585 7000 _http www Superchips com Superchip amp Superchips are registered trademarks of Superchips Inc Page 11 of 16 Form0141C 03 29 2007 Superchips Inc 9 Programming Section The MAX Micro Tuner will beep and display the message Turn Ignition OFF Press gt Turn the ignition to the OFF position and press the gt key on the keypad The MAX Micro Tuner will beep and blink the following message Initialization Please Wait After initialization is complete the MAX Micro Tuner will beep and display the message Turn Ignition ON Do NOT START Eng Turn the ignition switch ON The MAX Micro Tuner will beep once and display the following messages Ready to Install New TUNING The Ignition SW Must remain ON Press gt to Continue IMPORTANT NOTE Do not interrupt the MAX Micro Tuner programming cycle or disconnect it from your vehicle until the programming cycle is complete The programming cycle can take several minutes Press gt The MAX Micro Tuner will beep once and erase the present program The MAX Micro Tuner will blink the following message Erasing Present Program After the present program has been erased the MAX Micro Tuner will blink the following message Install TUNING The bottom line of the display shows the programming progress Once the programming sequence has been successfully accomplished on a vehicle the MAX Micro Tuner becomes LOCKED to that veh
9. Page 1 of 16 Form0141C 03 29 2007 Superchips Inc Superchips Model 1724 MAX Micro Tuner 2004 3 9L V6 Mustang amp 2004 4 6L V8 Ford Automobiles Vehicle Programming Instructions PLEASE READ THIS ENTIRE INSTRUCTION SHEET BEFORE YOU PROCEED Thank you for choosing the Superchips Model 1724 MAX Micro Tuner a state of the art instrument that allows you to install a Superchips performance program specifically tuned for your vehicle and your driving requirements You can select between a Performance program when you are using premium fuel and a program that provides optimum performance when using 87 octane fuel You can custom tune your shift points and shift firmness and optionally adjust the vehicle rom and speed limiters Vehicles with electronic speedometers allow for correction to compensate for gear changes Traction Control disable and adjustment of electric fan turn on temperature is also available on some vehicles This product is intended for use on unmodified stock engines Your Vehicle s STOCK Program The MAX MicroTuner stores a copy of your vehicle s original stock computer program Your vehicle computer must contain the manufacturer s STOCK factory program If you have used a programmer from another aftermarket company you must use their product to return your computer back to STOCK condition before proceeding If you have a performance enhancing chip installed it must be removed Your Vehicle and Service
10. Superchips Inc Page 2 of 16 Form0141C 03 29 2007 Superchips Inc Refund Policy If for any reason during the first thirty 30 days after your purchase of a new Superchips product Product you may return it to the place you bought it for a full refund of the purchase price credit or a replacement Product at the dealer s discretion This Guarantee does not apply to products purchased from auctions nor does it apply to Products purchased used Follow these procedures to get your refund or replacement 1 If you are returning a MicroTuner or Flashpaq use the MicroTuner or Flashpaq to return your vehicle to the stock settings for the vehicle Instructions are included in the user manual 2 Put the Product back in its original packaging 3 Make a copy of your sales receipt The sales receipt must be from the location where you purchased your Product and must include the name of the business its address and the part number or description of the applicable Superchips Product Invoices credit card statements or sales receipts from an online payment service company will not be accepted 4 Return the Product in its original packaging with a copy of the sales receipt to the place of purchase Superchips Inc Limited Warranty What is Covered This warranty covers any defects in materials or workmanship in any product sold by Superchips or its affiliates through its authorized dealers Product Warranty is valid only for n
11. de of the engine as shown in Figures 1 4 below There are a variety of fuse layouts You can find the specific location of the fuel pump fuse in your owner s manual Failure to remove this fuse may cause severe damage to your engine If you have difficulty finding the fuel pump fuse in your vehicle Removing the Fuel Pump Fuse Locate the auxiliary fuse box sometimes labeled Power Distribution Box usually located under the hood Open the hinged lid of the black plastic box There is usually a diagram of fuse locations on the inside of the lid Check your Vehicle Owner s Manual for the fuel pump fuse number Remove the Fuel Pump Fuse a Fig 1 2004 Ford Mustang Power Distribution Box location Superchips Inc 1790 East Airport Blvd Sanford FL 32773 407 585 7000 _http www Superchips com Superchip amp Superchips are registered trademarks of Superchips Inc Fig 3 Typical Fuse Arrangement 2004 Mustang Fuse 14 20 Amp Mini fuse Fig 4 Typical Fuse Arrangement for 2004 Mercury Grand Marquis Maurader Lincoln Towncar Ford Crown Victoria Fuse 1 5 20 Amp Mini fuse 4 Power Distribution SD Fig 2 Power Distribution Box location for 2004 Mercury Grand Marquis Maurader Lincoln Towncar Ford Crown Victoria Superchips Inc 1790 East Airport Blvd Sanford FL 32773 407 585 7000 _http www Superchips com Superchip amp Superchips are registered trademarks of Superchips Inc
12. descriptions that follow The MAX Micro Tuner will beep and display the message SHIFT POINT n n MIN ST MAX n n is 1 2 2 3 or 3 4 ST Stock Or Superchips The present Shift Point setting will flash MAX is approximately 10mph the STOCK setting MIN is approximately 10mph below the STOCK setting Use lt to lower the Shift Point gt to raise the Shift Point Press gt while MAX is flashing to select the Superchips Performance Program setting Press YES to save the desired Shift Point setting The MAX Micro Tuner will repeat this process for each Shift Point Editing the Shift Pressure Option Settings The Shift Pressure Option allows the user to set each Shift Pressure independently The choices are e Use the STOCK setting for the Shift Pressure e Adjust the Superchips Performance Program setting for the Shift Pressure The following screens for adjusting the Shift Pressure are the same for all Shift Pressures except the selected Shift Pressure replaces n n in the descriptions that follow After choosing the shift points you wish to use the MAX Micro Tuner will beep and display the message SHIFT PRESS n n MIN MAX n n is 1 2 2 3 or 3 4 The present Shift Pressure setting will flash The vehicle program determines the MAX setting MIN is the vehicle s stock setting Use lt to lower the Shift Pressure gt to raise the Shift Pressure Press gt w
13. ew products purchased through Authorized Dealers Proof of purchase is required for all warranty claims How Long Does the Coverage Last This warranty lasts for one 1 year from the date of purchase Coverage terminates if you sell or otherwise transfer ownership of the Product What will Superchips Do Superchips will repair or replace the defective or malfunctioning Product or any defective or malfunctioning part thereof at no charge This warranty covers parts and labor only Superchips will reimburse you for all reasonable shipping charges within the first thirty 30 days of purchase What Does This Warranty Not Cover This warranty does not cover any problem that is caused by abuse misuse acts of God or improper installation or repair by non Superchips personnel This warranty does not cover Products purchased used nor does it apply to Products purchased from auctions or entities that are not Superchips authorized dealers This warranty does not cover damage to your vehicle Use of the Product to change the performance characteristics of your vehicle could invalidate the warranty provided by the vehicle manufacturer Consult your vehicle warranty before using the Product on your vehicle SUPERCHIPS SHALL NOT BE LIABLE TO YOU FOR ANY CONSEQUENTIAL SPECIAL OR INCIDENTAL DAMAGES SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU How Do
14. fter Programming Don t Panic In some vehicles equipped with the Passive Anti Theft System or PATS once the MAX Micro Tuner begins saving the factory stock program the THEFT light begins blinking rapidly and may even blink in short and long pulses to alert the user to a problem Since the Superchips Max Micro Tuner is communicating directly with the PCM no other devices may interrupt As a result the PATS module flags this as an error or theft condition and goes into THEFT mode After the MAX Micro Tuner has completed the programming cycle the PCM is still fully able to communicate and appears normal However the vehicle may be in a No Start Condition and the THEFT light will be blinking rapidly Corrective Procedure This procedure should recover the vehicle and allow it to be started Therefore it is recommended that the MAX Micro Tuner_programming cycle be completed prior to recovery i e The user should allow the MAX Micro Tuner to upload the stock program and should select their choice of performance files and any user options if available Following instructions they should complete the programming process Once the vehicle has been programmed with the selected performance program complete the following steps to reset the PATS THEFT condition if necessary Disconnect the Superchips MAX Micro Tuner amp cable from the vehicle s computer interface connector If the vehicle will not start and the Theft Light is blinkin
15. g rapidly 1 Remove the Ground cable from the battery post for a period of thirty minutes to allow the vehicle DTC codes and Theft codes to clear 2 Re attach the Ground cable to the battery and start the vehicle as you normally would Error Notification In the event the programming cycle is interrupted the MAX Micro Tuner is designed to recover automatically Follow the on screen prompts If for any reason the MAX Micro Tuner fails to complete its programming cycle an error message will be displayed on the unit Please make note of the message displayed and contact Superchips Customer Service If you need assistance please contact your local dealer or call Superchips Customer Service at 407 585 7000 M F 8 00 AM till 5 00 PM EST Superchips Inc 1790 East Airport Blvd Sanford FL 32773 407 585 7000 _http www Superchips com Superchip amp Superchips are registered trademarks of Superchips Inc Page 15 of 16 Form 0141C 03 29 2007 Superchips Inc Page 16 of 16 Form 0141C 03 29 2007 Superchips Inc Superchips Inc 1790 East Airport Blvd Sanford FL 32773 407 585 7000 _http www Superchips com Superchips Inc 1790 East Airport Blvd Sanford FL 32773 407 585 7000 _http www Superchips com Superchip amp Superchips are registered trademarks of Superchips Inc Superchip amp Superchips are registered trademarks of Superchips Inc
16. hile MAX is flashing to select the Superchips Performance Program setting Press YES to save the Shift Pressure Custom Option setting The MAX Micro Tuner will repeat this process for each Shift Pressure Editing the FAN Turn On Temperature Option Setting The FAN Temperature Turn On Option allows you to turn on the vehicle s electric fans at one of the following temperatures Superchips Performance Program 160 180 or STOCK The MAX Micro Tuner will beep and display the message Set FAN Turn On XXXXXXX The present FAN Turn On Temperature setting is displayed Use lt or gt to change the FAN Turn On Temperature setting and YES to save the FAN Turn On Temperature Option setting Superchips Inc 1790 East Airport Blvd Sanford FL 32773 407 585 7000 _http www Superchips com Superchip amp Superchips are registered trademarks of Superchips Inc Editing the Speed Limiter Option Setting The Speed Limiter option allows the user to set the vehicle Speed Limiter to Use the Superchips Performance Program raised setting e Use the STOCK setting The MAX Micro Tuner will beep and display the message SPEED LIMITER Raise or Stock The current Speed Limiter setting will flash Use lt or gt to change the setting and YES to save the Speed Limiter Custom Option setting Editing the Traction Control Option Setting The Traction Control option allows the user to set the vehicle Tract
17. icle The MAX Micro Tuner may not be used to tune any other vehicle The MAX Micro Tuner may be used on other Ford vehicles as a DTC Reader 10 End of Programming Sequence When the programming sequence is completed the MAX Micro Tuner beeps and will display Please Wait The MAX Micro Tuner is testing to see if the Passive Anti Theft System is active If PATS is active the MAX Micro Tuner beeps and displays the message Resetting PATS Please Wait After accessing the vehicle s computer and PATS is not active the MAX Micro Tuner automatically clears the vehicle DTCs Superchips Inc 1790 East Airport Blvd Sanford FL 32773 407 585 7000 http www Superchips com Superchip amp Superchips are registered trademarks of Superchips Inc Page 12 of 16 Form0141C 03 29 2007 Superchips Inc The MAX Micro Tuner Beeps and displays the following messages Clearing DTCs Please Wait TUNING Complete Turn Ign OFF Remove the Ford MAX Tuner Re install the FUEL PUMP Fuse Turn the ignition OFF remove the cable from the diagnostic port and re install the Fuel Pump Fuse 11 Return to Stock Sequence IMPORTANT NOTE You MUST remove the fuel pump fuse from the vehicle fuse block before attempting to install a Performance Program or to return the vehicle to its STOCK condition Failing to do so can cause serious damage to your engine The Return to Stock Sequence is used to reprogram a vehicle previously
18. ion Control to Use the Superchips Performance Program disabled setting e Use the STOCK setting The MAX Micro Tuner will beep and display the message TRACTION CONTROL On or Off The current Traction Control setting will flash Use lt or gt to change the setting and YES to save the Traction Control Custom Option setting Viewing the Option Settings The MAX Micro Tuner will beep and display the message View Custom Opis YES or NO Press YES to view the present values of the Custom Option Settings Press NO to go directly to the programming process at Step 8 below The MAX Micro Tuner will beep and display the message Press Any Key to Continue Press any key on the MAX Micro Tuner keypad The Custom Options current settings will be presented in order Press any key to view the next Custom Option setting Press NO to continue without viewing the Custom Option Settings The MAX Micro Tuner will beep and display the message Install TUNING YES or NO Press YES on the MAX Micro Tuner keypad to continue with the Programming process at Step 8 below Press NO to stop the process The MAX Micro Tuner will beep and display the message Finished with Tuner YES NO Press NO to start over at Selecting Tune Vehicle Diagnostics at Step 2 Press YES to go to the End of Programming Sequence at Step 9 below Superchips Inc 1790 East Airport Blvd Sanford
19. t to Continue Other error codes with or without explanations may be displayed Pressing the gt key will cause the MAX Micro Tuner to beep and display the message Please Wait After a few seconds the MAX Micro Tuner resets and returns to the power up self test Saving the STOCK program for the vehicle The manufacturer s STOCK program is first saved in the MAX Micro Tuner to allow the vehicle to be reprogrammed to STOCK condition if necessary The STOCK program is AUTOMATICALLY saved only the first time the vehicle is programmed Once the MAX Micro Tuner has established communications it will beep and display the following message for approximately 3 seconds Please Wait After initialization is complete the MAX Micro Tuner will beep and start saving the stock program This will take about three minutes The MAX Micro Tuner will blink the following message Saving Stock The bottom line of the display shows the progress of the stock upload When completed the MAX Micro Tuner checks to see if the stock program it has uploaded can be found in its internal database If not it will display the message Tuner Requires an Update Call Superchips or Check Vehicle application Press any key to continue If the stock upload is found in the internal database the MAX Micro Tuner will beep and display the message Please Wait Superchips Inc 1790 East Airport Blvd Sanford FL 32773 407
20. the keypad saves the Custom Option setting Press any key on the keypad to continue The MAX Micro Tuner will beep and display Manual Trans YES NO Press YES if the vehicle has a Manual Transmission Shift Points and Shift Pressures are not options on Manual Transmission vehicles Press NO if the vehicle has an Automatic Transmission Editing the Shift Points Option Settings The Shift Point option allows the user to set each Shift Point independently The choices are e Adjust from STOCK or the gear corrected STOCK Shift Point 10mph e Use the Superchips Performance Program Shift Point setting Superchips Inc 1790 East Airport Blvd Sanford FL 32773 407 585 7000 _http www Superchips com Superchip amp Superchips are registered trademarks of Superchips Inc Page 9 of 16 Form0141C 03 29 2007 Superchips Inc Page 10 of 16 Form0141C 03 29 2007 Superchips Inc Some basic rules are implemented by the MAX Micro Tuner for Shift Point options e Ifthe Shift Point is raised the Down Shift point remains at the STOCK or Superchips Performance Program setting e Ifthe Shift Point is lowered both the Up Shift and Down Shift settings are lowered proportionally e The WOT Wide Open Throttle setting is raised or lowered proportionally with the Up Shift setting The following screens for editing the Shift Points are the same for all Shift Points except the selected Shift Point replaces n n in the
21. tion that can be harmful to your engine The 87 OCTANE tuning level provides optimized engine performance and enhanced transmission tuning when 87 octane fuel is used The 87 OCTANE tuning level may not be available for all vehicles If your vehicle is a supercharged Cobra an HP4 tuning level may be offered in lieu of the 87 OCTANE tuning level The MAX Micro Tuner will Display the following Tuning Level XXXXXXXX Pressing lt and gt on the keypad changes the fuel setting Pressing YES on the keypad saves the tuning level setting 6 Editing the Custom Options Settings The MAX Micro Tuner will beep and display Edit Custom Opts YES or NO Press YES to make changes to the Custom Option Settings Press NO to bypass the Custom Options and go directly to Viewing the Option Settings at Step 7 that follows Superchips Inc 1790 East Airport Blvd Sanford FL 32773 407 585 7000 _http www Superchips com Superchip amp Superchips are registered trademarks of Superchips Inc The MAX Micro Tuner will beep and display the keys to use while editing the Custom Option settings Adjust lt or gt Save YES Press Any Key to Continue Pressing lt or gt on the keypad adjusts the Custom Option setting Pressing YES on the keypad saves the Custom Option setting Press any key on the keypad to continue The MAX Micro Tuner will beep and display
22. tuned with the Superchips MAX Micro Tuner with its original stock tuning Follow the steps described in Connecting the Superchips MAX Micro Tuner to Your Vehicle at Section 1 Following the typical start up messages if the MAX Micro Tuner has been previously used to program a vehicle the MAX Micro Tuner will beep and display Micro Tuner is VIN Locked This indicates the MAX Micro Tuner has been previously used to program a vehicle It should not be used program another vehicle The MAX Micro Tuner will continue to operate normally on the original vehicle After re establishing communications the MAX Micro Tuner will display the following message RETURN to STOCK YES or NO If NO is pressed the MAX Micro Tuner will return to nstalling the Superchips Performance Program at Step 5 If the YES key is pressed it will beep once and display the following message Turn Ignition OFF Press gt Turn the ignition to the OFF position and press the gt key on the keypad The MAX Micro Tuner will beep and blink the following message Initialization Please Wait After initialization is complete the MAX Micro Tuner will beep and display the message Turn Ignition ON Do NOT START Eng Superchips Inc 1790 East Airport Blvd Sanford FL 32773 407 585 7000 _http www Superchips com Superchip amp Superchips are registered trademarks of Superchips Inc Page 13 of 16 Form0141C 03 29 2007 Superchips Inc
23. uperchips Inc Page 3 of 16 Form0141C 03 29 2007 Superchips Inc Page 4 of 16 Form 0141C 03 29 2007 Superchips Inc About Maximum Trailer Weight The original manufacturer of your vehicle has specified a Maximum Trailer Weight for your vehicle It may be found in your vehicle owner s manual This Superchips product is designed to increase your engine power and performance It does not change the engine suspension or drive train characteristics that limit the maximum trailer weight your vehicle is designed to tow Towing trailer weights above the maximum trailer weight specified by the vehicle manufacturer may cause transmission or other damage If you wish to tow greater than the maximum trailer weight for your vehicle modifications to your vehicle may need to be made Consult your performance auto mechanic for the proper vehicle modifications Damage caused by towing weights greater than the maximum trailer weight specified for your vehicle shall not be the responsibility of Superchips Inc THIS MAY BE THE MOST IMPORTANT INSTRUCTION IN THIS ENTIRE MANUAL Because of techniques that the Ford Motor Company uses with the ECM in gasoline vehicles for safety YOU MUST REMOVE THE FUEL PUMP FUSE BEFORE ATTEMPTING TO INSTALL A PERFORMANCE PROGRAM OR TO RETURN THE VEHICLE TO ITS STOCK PROGRAM Typically the fuel pump fuse is found in an auxiliary fuse box often called Power Distribution Box located under the hood on the right si
Download Pdf Manuals
Related Search