Dynnox
Contents
1. the pressing in of the springs of the commercial vehicle The lighter the weight on Dynnox is and or the heavier the commercial vehicle is loaded the more centimetres have to be added to A 4 3 Checking and adjusting the play in the legs If the frame is folded out each leg is secured by a hook connection Please follow the road map checking hook connection and carry out the correct steps Check flow chart hook connection Start Check the pin lock under the Dynnox frame section 4 3 1 Is the clearance between the hooks the smallest possible Check the clearance inside the pin lock section 4 3 2 Yes gt Set clearance for the pin lock section 4 3 3 Does the mechanism turn correctly Yes The clearance is set correctly No 4 3 1 Checking the play visually 1 Place the frame on its brake by locking the castor wheels 2 Stand at the side of the frame 3 Place your foot against the castor wheel and pull the frame with one hand so that the legs are pushed inside Figure 12 Hold this position 4 Now visually check Figure 13 whether the play between the hooks is minimal See Figure 14 for the desired situation 5 Repeat steps 2 through 4 for the other side of the mechanism REMARK If you want to visually check the play at the rear side you follow the above steps but then at the rear side of the frame Go to the flow chart to check the h2. are worn and therefore straight C 0 mm Dynnox may no longer be used The legs can then come loose during use e Whether the mushrooms Figure 20 A and B are tightened sufficiently The mushrooms should be tightened with Loctite blue e Whether the legs are properly tightened Figure 11 If the legs are loose then tighten the two bolts of each leg firmly Check 1 time per month e The locking of the frame on the vehicle interface Figure 24 Contact your authorised dealer if the locking does not function properly e Whether the safety hook Figure 3 A19 of both the front and rear mechanism Figure 3 A8 amp AQ hooks properly to the counter hook on the loading ramp Figure 4 B12 If the safety hook does not properly hook on the counter hook then please contact your authorised dealer The safety hook should hook at least on two thirds of the counter hook Figure 3 8 3 Maintenance schedule e The locking mechanism should be checked every 3 to 5 weeks after use by an authorised dealer e The small rollers on the safety activator should be greased every three months e As user you should check at least once a week The legs Figure 3 A6 amp A7 are locked properly The mushroom Figure 3 A10 and the locking pin Figure 3 A11 are not loose e The locking mechanism should be checked by an authorised dealer every half year e The complete Dynnox vehicle interface should be checked by an authorised dealer every half year 9 Moun
3. hands on the sides of Dynnox in order to prevent the danger of jamming Check after folding out the loading ramp Figure 4 B1 whether the hinges Figure 4 B4 have the same tension D Check whether the loading ramp is in horizontal position and folded out completely Figure 36 Step 2 placing the Dynnox frame in the commercial vehicle A Place the Dynnox frame in the middle straight against the loading ramp Figure 37 B Check whether the positioning wheels are at the correct height compared to the slope of the loading frame see Section 4 2 C Pull the Dynnox frame backwards up to around 30 cm distance from the loading ramp Figure 38 If the positioning wheels are not at the correct height there are three possible causes for that 1 The foundation is not level If that is the case please look for another parking place 2 The height of the legs is not set properly See Section 4 2 for more information on setting the legs 3 The weight of your vehicle has suddenly increased or decreased because of which the height settings are no longer correct D Check whether the lock of the bracket is open Figure 24 E Drive the frame at walking distance into the Dynnox vehicle interface until the intermediate legs at the front Figure 3 A5 are unlocked Figure 39 and subsequently stop Step 3 locking the rear legs A Grab the intermediation connection pipe between the two rear legs and turn the rear legs upwards until the fin
4. Y N NE STRONG THROUGH SIMPLICITY AND INNOVATION User manual Manual for the user Dear client Thank you for purchasing Dynnox This manual contains all information necessary in order to quickly become accustomed to the product We kindly request you to carefully read this information before you start working with the product This manual is intended for the end user of Dynnox In the Table of Contents you can read where the information you need can be found in the manual Please consult the added booklet for the images in this manual Images for the user manual This is the original manual Please contact your dealer see front page for more information or ordering manuals Please carefully store this manual We wish you a lot of pleasure with your Dynnox The Dynnox Team Innobase BV Vicarielaan 55 NL 3401 AR IJsselstein The Netherlands Tel 31 0 306877301 Fax 31 0 842251757 E mail info dynnox com Website www dynnox com Disclaimer Dynnox may only be used as transport system in order to load unload and transport your load Innobase BV cannot be held liable for possible damage caused by improper incorrect or irresponsible use You must read and understand this manual in full before use Safety should always be guaranteed so that the user and third parties can safely make use of Dynnox You should thereto also comply with the maintenance requirements Dynnox may only be mounted and or demounted by an authori
5. al position has been reached Caution The rear legs should be locked with a locking system that is mounted to the construction module This system differs per construction module and can therefore not be displayed in this manual Your authorised dealer knows everything on this Caution Stay clear of moving parts during the use of Dynnox in order to prevent the danger of getting jammed Step 4 Locking the frame A Push with some force against the frame until it does not go further B Check at the brackets whether the frame is in its utmost position Figure 39 C Check whether the frame is locked by carefully but with some force pulling it towards you Step 5 locking the loading ramp A Turn the loading ramp up until it cannot go any further Once you hear a click sound this means that the loading ramp is locked Figure 40 B Check the locking by grabbing the ramp with two hands and carefully pulling it towards you with some force 8 Maintenance and maintenance scheme 8 1 General All parts that are screwed loose should be mounted once again with Loctite blue Never use the same lock nut twice 8 2 Checking during use Check 1 time per week e The play in the leg hook locking The leg hook locking Figure 3 A18 should be turned fully like shown in Figure 14 If the hook is not fully turned please follow the instructions described in Section 4 3 e Whether the hooks on the legs are not worn Figure 19 C If the hooks
6. bolt less to the left you increase the play B Figure 19 The objective is to obtain play B as little as possible without the mechanism jamming Hold the bolt with an allen key and tighten the nut Check the functioning of the mechanism see Section 4 3 2 Check the play Repeat steps 1 through 6 for the other three legs Place back the caps ate ae REMARK If you want to check the play at the rear side you follow the above steps but then at the rear side of the frame Go to the flow chart to check the hook connection in Section 4 3 in order to continue the checking procedure 4 4 Setting the three mushrooms and the locking pin On your Dynnox frame there are three mushroom Figure 20 A and one locking pin Figure 20 B These should be enabled to supply glide into their hooks Figure 21 To this means the play between the parts should be sufficient See Figure 22 and Figure 23 for the desired situation AN Caution The distance A in Figure 23 should be at most 1 mm 4 4 1 The mushrooms You can adjust the play by adding or removing rings As a standard two rings suited for an M10 bolt are supplied per mushroom and locking pin AN Caution Use Loctite blue when mounting 4 4 2 Locking pin Figure 24 The lock has two positions The locking pin should be entered into the open position of the lock When driving into it you should observe a clear click sound The lock is activated by a cable The cable is pulled
7. by a grip Figure 4 B10 This grip is standard mounted on the left railing Figure 4 B6 of the vehicle interface Caution Your dealer might have chosen to mount the grip at a different location Consult your dealer on this 5 Choosing a parkin lace When choosing a parking space the following elements should be taken into account e The vehicle must be parked on an even surface with a maximum slope of 3 Figure 25 e See to sufficient space at the side and or rear of the commercial vehicle in order to unload the frame at least 1 5 times the length of the frame Figure 26 e The space at the rear and or the side of the commercial vehicle should be level with the foundation of the commercial vehicle Figure 26 e Dynnox cannot be used at a sidewalk Figure 27 e Select a place without pitfalls such as for example drains or sewage systems Figure 27 6 Unloading the Dynnox frame 6 1 Advance warnings Caution Check where you have parked See Chapter 5 Caution Always check before and after use whether Dynnox is locked Caution Stay clear of moving parts during the use of Dynnox in order to prevent the danger of getting jammed See Chapter 3 Caution Only use Dynnox on a levelled surface with a maximum slope of 3 Figure 25 Caution Check after folding out the loading ramp Figure 4 B1 whether the hinges Figure 4 B4 have the same tension 6 2 Unloading the Dynnox frame in six steps In order to unload D
8. ers describe the frame width e L 96 2 cm e 46 46 cm e XL 125 cm e 53 53 cm e 63 63 cm 2 2 Standard dimensions 2 2 1 The frame Figure 1 Legend at the image F Front B Rear side FL Frame length FB Frame width DB Dynnox width The height of Dynnox depends on the height between the loading ramp of the commercial vehicle and the outside surface Dynnox L46 Dynnox XL36 Frame width 46 cm Frame width 36 cm Frame length 96 2 cm Frame length 125 cm Weight 42 kg Weight 42 kg Caution This model is smaller at the Caution The maximum height for this front side namely 36 cm model is 58 cm Dynnox XL53 Dynnox XL63 Frame width 53 cm Frame width 63 cm Frame length 125 cm Frame length 125 cm Weight 44 5 kg Weight 47 kg The Dynnox width Frame width 19 cm The Dynnox length Frame length 4 5 cm 16 cm above the frame the construction module can became up to 20 cm wider 2 2 2 Dynnox vehicle interface Figure 2 Legend at the image e DL Dynnox length e DB Dynnox width Dynnox L46 Dynnox XL36 Width 764 mm Width 664 mm Length 1470 mm Length 1470 mm Weight 28 5 kg Weight 29 kg Dynnox XL53 Dynnox XL63 Width 834 mm Width 934 mm Length 1470 mm Length 1470 mm Weight 30 kg Weight 31 kg A The steel plates are optional de
9. ight side e L Left side B1 Loading ramp B9 Locking cable B2 Loading ramp axis connection B10 Lock grip 2x left and right B11 Wooden plate B3 Locking of loading ramp B12 Counter hook B4 Hinge of loading ramp 2x B13 Mounting of steel plate three parts B5 Anchor element 3x B14 Cable stopper positioned under the profile B6 Guide at left B15 Small roller 2x B7 Guide at right B16 Cross member B8 Lock The wooden plate is not supplied with Dynnox 3 Important Precautionary measures and advance warnings Only use Dynnox on a levelled surface with a maximum slope of 3 Figure 25 Always check before and after use whether Dynnox is locked 4 All repairs should be carried out by an authorised dealer Dynnox may only be used as transport system in order to load unload and transport your load Dynnox is not suited to transport people and or animals Dynnox is not liable for all products and or construction modules that are built on and or at the frame Stay clear of moving parts during the use of Dynnox in order to prevent the danger of getting jammed When loading Dynnox in the green zone you keep both hands on the push bracket of the construction Figure 5 Mounting installation and taking into use 4 1 General If the construction module of your Dynnox frame is higher than 50 cm or heaver than 50 kg then please fix the height with a least 2 persons Caution See to sufficient space at
10. nvironment dismantling storage and transport 12 1 Environment Upon completion of the life span of the product it should be separated from other waste If the product is no longer usable you should bring it to a collection point assigned for that by the authorities In that way you contribute to a cleaner environment 12 2 Dismantling Inform in your region on the options to hand in Dynnox upon discontinuation of use If you do not have these options available then skilfully remove all reusable components such as metals and fastening materials yourself Remove the plastic parts for recycling 12 3 Storage and transport If you store or transport the product please see to it that you properly pack the product Storage should take place in a dry environment Warranty registration e BEEN eee EEN meme mmm mem Assembly done by Name of technician The user has received the instructions concerning the checks to apply during use He is aware that he must have read the instruction manual before operating the Dynnox User approval Distributor approval BE Signature Signature and stamp
11. of which the height settings are no longer correct Caution Stay clear of moving parts during the use of Dynnox in order to prevent the danger of getting jammed B Stop the legs with one foot and simultaneously pull the Dynnox frame further outwards Figure 34 C Visually check whether the rear legs are properly locked Figure 14 Step 6 locking the loading ramp A Closing the loading ramp by turning it upwards until the highest position has been reached You should hear a click sound B Check whether the loading is properly locked by grabbing it with two hands and carefully pulling it towards you with some force 7 Loading the Dynnox frame 7 1 Advance warnings Caution Check where you have parked See Chapter 5 Caution Stay clear of moving parts during the use of Dynnox in order to prevent the danger of getting jammed See Chapter 3 Caution Only use Dynnox on a levelled surface with a maximum slope of 3 Figure 25 7 2 Loading the Dynnox frame in five steps In order to load Dynnox on the commercial vehicle the following steps should be followed Step 1 folding out the loading ramp A Check whether the hinges and the axes are mounted Figure 28 A and C B Unlock the loading ramp by pushing up the small pins Figure 28 B AN Caution See to sufficient space in order to be able to open the loading ramp Figure 29 C Carefully lower the loading ramp as far as possible AN Caution Do not place your
12. ook connection in Section 4 3 in order to continue the checking procedure 4 3 2 Checking the play physically Place the frame on its brake by locking the castor wheels Stand at the front side of the frame Place your foot against the castor wheel and pull the frame towards you with one hand Figure 12 Push with your other hand against the central unlocking point of the mechanism Figure 15 at your side A or B from the bottom 5 The bracket axis Figure 3 A12 should be able to turn without friction rep REMARK If you want to physically check the play at the rear side you follow the above steps but then at the rear side of the frame Go to the flow chart to check the hook connection in Section 4 3 in order to continue the checking procedure 4 3 3 Adjusting the play on one single leg Figure 3 A6 amp A7 If it has been established that the play of the mechanism Figure 3 A8 amp A9 at the front and or rear side is too large or too little you should adjust the play at each leg You can do this as follows 1 Remove the plastic cap from one of the legs You can now observe the setting bolt from the top Figure 16 2 Tighten the nut loose some turns with a socket wrench no 13 Figure 17 Prevent that the setting bolt turns along by with holding it with a allen key 3 Tighten the setting bolt in order to adjust the play If you tighten the bolt more to the right you increase the play A Figure 18 If you tighten the
13. pending on the mounting choice and your commercial car supplier B Wooden plate with a thickness of at least 12 mm 2 3 Environmental influences Only use Dynnox on a levelled surface with a maximum slope of 3 Figure 25 The product may not be used if the height of the foundation on which your vehicle is located differs from the height of the foundation on which Dynnox is placed Think for example of a deviating height of the road compared to the sidewalk 2 4 Tools required e Socket wrenches e Socket wrenches e Measuring tape 2 5 Main component parts A Dynnox frame Figure 3 Legend at the image e F Front B Rear side e e R Right side e L Left side A1 Frame A13 Saving for the benefit of tightening ribbon A2 Castor wheel with brake 3x left and 3x right A3 Leg locking 4 x 2 for A6 and A7 A14 Hole mounting construction module 5x left A4 Intermediate leg at rear 2x and 5x right A5 Intermediate leg at front 2x A15 Small cap 2x left and 2x right A6 Wheel leg at rear 2x A16 Loading wheel 2x A7 Wheel leg at front 2x A17 The leg hook locking 4x A8 Rear mechanism A18 The safety hook 2x AQ Front mechanism A19 Wheel support frame 2x A10 Mushroom 2x at front and 1x rear left A20 Wheel support rear intermediate leg A4 A11 Locking pin 2x A12 Bracket axis 2x left and 2x right A21 Loose wheel 2x B Dynnox vehicle interface Figure 4 Legend at the image e R R
14. rrssssrrrrssrrrrrrrrnrrrssnrrrrsrnrrrresrrrresrnnn 9 Aid The mMushrooms ooie a e e R E EEE EOS EAA A btu EA ENEE Eei E 9 4 4 2 LOCKING DIN EE 9 5 CHOOSING a parking plat EET Er Eee n kek ke 9 6 Unloading the Dnk frame sesniienden chess arcarstines winnie vesesene xiuxmncdeceronducetediealteainedecnsuenvesweenns ande 10 SE MOE EE EEE ER 10 6 2 Unloading the Dynnox frame in six steps Lasses nese Femmike needed ER REE 10 Vo Loading the Dynnox LEE EEE EE AE a anon 11 Fa PTE Warnings rea Ge 11 7 2 Loading the Dynnox frame in five steps Kea Seen ATV ikdinn 11 8 Maintenance and maintenance scheme wssccovsovesieneseeriede sun tk ERE E RR R ERR E ERR REE ERE REE ERE ERE ERE E ERE ERE ng 12 GE 11 EE ER EE EE EE NN tinted 12 8 2 Checking GQUENNG USE 4 12 8 3 Maimtenance STEINE ae spn iano aroro noiae EEE E a n a a i En 12 9 MOUNTING and making 005E ursis a a EEEa A A a 13 GET gg a a as bee ed acd E EE NE NN 13 9 2 MUSMEOOM S eiren EE EE EE EE E E EE E E 13 LO WAKTANCY EE EE E A EO E e A a E EAA ne 13 1i Solving PrOD EM S pek eda ee E 13 12 Environment dismantling storage and TANSOOM biiaiiviwdimirnrieiuididedenielemmminiirlnnraehd wud erdananua 14 12 1 PT MENE EEN EEN REEE EE E T E E EEEE EEE 14 22 DIN vrede 14 12 3 Storage AER aa ENNEA 14 1 Introduction 1 1 Product description Dynnox is a system to improve the loading unloading and transporting of goods Dynnox can be used in combination with a thereto suitable commercial
15. sed dealer in your neighbourhood Table of contents Manual TE EE vasre AE ae A ebtesereusasshosannabeates 2 Bis EEE EEE EN EE EN E 2 TENNE es 3 al ea og ET EE NE EN TE 4 Lid Product descriptioN EE EE E E NN EE 4 AE DEE RE RE RE EEE EE E E al E Es EDER ES e ER 4 2 TM E E R E E E 4 2 1 General product specification EE EE RE A EE A EE a Een 4 2 2 Standard dimension Si eden ke ed E RE a te 4 PPA TNE ME 4 2 2 2 Dynnox vehicle interface Lavard 5 2 3 Preslav ANGA 5 2 TEMA 5 2 5 Main component P SE siiiiiuiminicianni cw iwi oie cesnmiudr edd A E wd EEE dd seriene 5 3 Important Precautionary measures and advance warningS xarunnnnnnnnnnnnnnnnnnnernnrnnrnnrnnnnnnnnnnvnnvnnvn 6 4 Mounting installation and taking into use asesiiocotnisrenrtun etaweus tuned ERE REE E REE ERR E REE REE ERE ERNE ERE NERE REE 6 Ai MEY RENEE EE NE EN ET ERE REGERER SETE 6 4 2 Setting of the height OF DYNNOX suc ous cee renew dard ai SENDE DEDE DS DEDE LEDEDES SD DEAD An 7 4 3 Checking and adjusting the play in the legs sssseeeeeeeee kk tk kk ER dieannennndin euniiewiiauiiewuded ERE ERE ERE 8 43 1 Checking the play visually sere 8 4 3 2 Checking the play physically sssssssasssnsnnnsurnsnnnnnarnsnnnnnarsnnnrenarsnnarsnanssuansnnrennnnsnnrennnnsnnn 8 4 3 3 Adjusting the play on one single le g ss ssssssssssnssrrrrrsrrrrrrrrrrrrsssrrrrrnnnrrnrsrnrrrennnrreennnnene 9 4 4 Setting the three mushrooms and the locking p N sssssssssr
16. sed in a commercial vehicle The loose load that is taken along once in a while The type of commercial vehicle The premises where you park on which you unload and or load Dynnox Setting the height of Dynnox Figure 10 Caution The setting of the height of a Dynnox should always take place when the commercial vehicle is loaded averagely A the height between the loading ramp and the foundation B the height between the bottom of the frame and the foundation In order to adjust the height of the Dynnox frame you carry out the following actions 1 Measure height A 2 Determine the desired height B This is height A at least 1 5 cm and at most 2 5 cm 3 Un tighten the two socket wrench bolts at a random leg Figure 11 Caution Only loosen one leg at the time and pay attention to the weight of the load of the frame If the construction module is higher than 50 cm or if the construction module is heavier than 80 kg then these actions should be carried out by at least two persons 4 Adjust the height of the leg until the desired height B has been reached Figure 11 5 Safeguard the leg by tightening the socket head screws 6 Repeat the steps 3 4 and 5 for the other legs Caution Dynnox should be set level Caution Tighten the socket head screws firmly Caution The securing of the legs should be checked each month The difference between the minimum and maximum height depends on the weight on a Dynnox and
17. t the same time you pull the Dynnox frame towards you AN Caution The locking grip Figure 4 B10 can be placed elsewhere in the vehicle by the dealer Step 4 locking the front legs A Pull the Dynnox frame with two hands from the commercial vehicle until the legs are lowered Figure 32 Use the grip that is mounted on the construction module for this Caution You may only pull the Dynnox frame from the commercial vehicle if the foundation is level and has a slope of at most 3 Caution Keep both hands on the grip and stay clear of moving parts Caution Please pay attention that you pull a mass towards to yourself B Stop the front legs with one of your feet do not use the brake and simultaneously pull the Dynnox frame further towards yourself Figure 33 Slowly pull the Dynnox further until the intermediate legs at the rear Figure 3 A4 have lowered You can now continue with the next step Step 5 locking the rear legs A Stand at the side of the frame Caution If the horse wheels sway more than 4 cm above the foundation Figure 34 you must stop unloading the Dynnox frame There are three possible causes The foundation is not level If this is the case you reload your Dynnox once again see Chapter 7 and look for another parking place The height of the legs is not set properly See Section 4 2 for more information on setting the legs The weight of your vehicle has suddenly increased or decreased because
18. the side and or rear of the commercial vehicle in order to unload the frame from it Caution Always check before and after use whether Dynnox is locked Caution Only use Dynnox on a levelled surface with a maximum slope of 3 Figure 25 Caution Check after folding out the loading ramp Figure 4 B1 whether the hinges Figure 4 B4 have the same tension 4 2 Setting of the height of Dynnox Figure 6 Legend at the image e A Slope Basic assumptions For the correct operation of the system it is important to set the height of the Dynnox frame The correct height is obtained if the positioning wheels end up at the height of the slope of the loading ramp Figure 7 The difference between the top and the bottom of the slope amounts to maximum 4 cm This means that setting it should be done precisely The loading wheels of the Dynnox frame may never exceed the slope otherwise the mechanism is not activated and the legs will not fold out Figure 8 In the Figure the height upper side slope is indicated with A Distance B indicates that the loading wheels are positioned too high Caution If the height is not set correctly then NEVER lift the Dynnox The safety mechanism will not function properly Figure 9 In order to stay within the lower and upper side of the slope it is important that the following is taken into account e The standard load of the commercial vehicle The loading of Dynnox especially if several Dynnox are u
19. ting and making loose 9 1 General All parts that are screwed loose should be mounted once again with Loctite blue Never use the same lock nut twice If you demount parts yourself from your Dynnox frame and or vehicle interface within the warranty period all warranty on your Dynnox lapses You should have this carried out by an authorised Dynnox dealer You can find the nearest dealer on our website www dynox com 9 2 Mushrooms You can loosen mushrooms with a socket wrench no 17 Caution It is highly important that the correct amount of rings is used when mounting the mushrooms See Section 4 4 for more information 10 Warranty One year warranty applies to all parts on the conditions that you use and maintain your Dynnox in accordance with the instructions in this manual 11 Solving problems Problem Possible solution Dynnox makes a shrieking sound The small rollers on the safety activator should be greased The height of the frame should be set once again See Section 4 2 Check whether the play in the legs is not too large See Section 4 3 The legs in front and or at the rear do not turn Check whether the springs of the mechanism did loose not turn loose and or have sufficient tension The height of the frame should be set once again See Section 4 2 Check whether the play in the legs is not too large See Section 4 3 The frame does not easily loosen from the lock See section 4 4 12 E
20. vehicle Dynnox can be designed with various types of mounting modules This manual only deals with the Dynnox frame and the Dynnox vehicle interface Consult your dealer in order to check whether your means of transportation is suited in combination with Dynnox and for more information on available construction modules You can also consult our website www dynnox com 1 2 Glossary Dynnox frame the part of the Dynnox system that carries the construction Dynnox vehicle interface the part of the Dynnox system that is built into the commercial vehicle Construction module a construction module is understood to mean the part that is firmly mounted on the frame Dynnox system the Dynnox vehicle interface and the Dynnox frame Commercial vehicle the vehicle in which the Dynnox vehicle interface is built in Foundation the ground around the parked commercial vehicle Loctite Loctite blue with reference 243 2 Technical specifications 2 1 General product specifications Product description Name Dynnox Model type L 46 XL 53 XL 63 XL 36 Serial number see frame of respective model Explanation type number of our Dynnox system Various types of the Dynnox system exist These types have their own weight and dimensions Which type and the corresponding weight and dimensions you have you can deduct from the type number An example of a type number is XL53 The letter s describe s the frame length The numb
21. ynnox from the commercial vehicle the following steps should be followed Step 1 folding out the loading ramp A Check whether Dynnox is locked B Check whether the hinges and the axes are mounted Figure 28 A and C C Unlock the loading ramp by pushing up loading ramp lock with one hand Figure 28 B AN Caution See to sufficient space in order to be able to open the loading ramp Figure 29 D Carefully lower the loading ramp as far as possible Caution Do not place your hands on the sides of Dynnox in order to prevent the danger of jamming E Check whether the loading ramp is in horizontal position and folded out completely Figure 29 Step 2 unlocking the legs A Take the intermediate pipe of the legs with one hand and unlocked the front legs with the other hand Caution The way in which the legs are locked is determined by the supplier of the construction module and can therefore not be displayed and or described here Your authorised dealer knows everything on this Caution The frame should release from the lock without friction Should pulling out the frame require too much energy then the locking pin and the mushroom should be pulled from each other You should subsequently tighten the locking pin and the mushroom firmly B Place the front legs on the loading ramp Figure 30 Step 3 unlocking the frame A Grab the grip on the construction module and pull the locking grip Figure 31 at the same time A
Download Pdf Manuals
Related Search
Dynnox dynnox minoxidil dynox radio dynox lift chair dynoxan dynox home dynox recliner dynoxx dynox pluto serum bank reddit dynoxidin dynox producer dynoxin dynox23 dynox pluto serum bank