Home

User Manual - Invacare Continuing Care

Contents

1. Needs Reset will not operate The control box buttons for 5 seconds The bed will beep and stop may beep when pendant function is beeping when reset is complete Then press the bed pressed up button If the bed beeps the actuators are out of sync Continue rising to the highest position to synchronize the actuators Part No 1153410 65 Invacare CS Series Beds 10 TROUBLESHOOTING EFFECT POSSIBLE CAUSE VERIFICATION CORRECTIVE ACTION Actuator not working HI LO lock out is on For non openbus CS3 CS5 A Rotate the lockout dial to the unlocked position Lockout box a square black box horizontal or flip switch to OFF with a toggle switch When the switch is towards ON side the HILO on the hand pendant will not function There is no LED light For openbus beds CS7 CS9 CS9FX600 The lockout box a flatter rectangular white box with a toggle dome button and LED light When the light is on the HILO on the hand pendant will not function Lockout LED on the Attendant Toggle off the individual function lockout LED should Control Pad ACP is ON be OFF EE Check cable connections visually Connect any loose cable couplings and or power supplies Faulty actuator Disconnect power supply swap Contact Invacare Continuing Care Service cable from unresponsive actuator Department 1 800 668 2337 with a functional actuator Reconnect power and test functions Faulty actuator will not work regardless of the connecti
2. OPTIONS The underbed light can be turned on by pressing the blue light button on the hand pendant Press again to turn off N Attendant a e Rp ep Control Panel Fg a oe Lockout Alternate Pendants All functionality is the same on the alternate pendants except where noted Under the Bed Light YA ERS AP TAU 7 F4 Y ia LE FIGURE 2 4 Function Pendant Invacare CS Series Beds 52 Part No 1153410 8 OPTIONS 8 7 Optional Trendelenburg and Reverse Trendelenburg Attendant Control Panel A CAUTION Use of Trendelenburg or Reverse Trendelenburg feature may not be appropriate for certain patients Trendelenburg and Reverse Trendelenburg should only be used on the advice of a medical practitioner DO NOT install a CS Bed Extender on a bed that is equipped with the Trendelenburg and Reverse Trendelenburg feature Under Nurse Bed Light Call FIGURE 3 Optional Trendelenburg and Reverse Trendelenburg Attendant Control Panel Part No 1153410 53 Invacare CS Series Beds 8 OPTIONS 8 8 Pendant HI LO Lock Out Optional When in the OFF position the HI LO function on the pendant will NOT operate When in the ON position all pendant functions will operate normally The head function and knee foot function on the pendant remains operational whether the lock out is activated or deactivated HI LO Attendant Control Lockout Lockout at fo
3. is necessary this bed should be observed to verify normal operation in the configuration in which it will be used Guidance and Manufacturer s Declaration Electromagnetic Emissions The CS Bed is intended for use in the electromagnetic environment specified below The customer or the user of the CS Bed should assure that it is used in such an environment Emissions Test Compliance Electromagnetic Environment Guidance RF emissions The CS Bed uses RF energy only for its internal function Therefore its RF emissions CISPR I are very low and are not likely to cause any interference in nearby electronic equipment RF emissions Class B The CS Bed is suitable for use in all establishments including domestic CISPR establishments and those directly connected to the public low voltage power supply Harmonic emissions IEC 61000 3 2 network that supplies buildings used for domestic purposes Voltage fluctuations flicker emissions Complies IEC 61000 3 3 Invacare CS Series Beds 16 Part No 1153410 3 EMC INFORMATION Guidance and Manufacturer s Declaration Electromagnetic Immunity The CS Bed is intended for use in the electromagnetic environment specified below The customer or the user of the CS Bed should assure that it is used in such an environment Immunity Test IEC 60601 Test Compliance Level Electromagnetic Environment Guidance Level Electrostatic discharge ESD IEC 61000 4 2 Electrical fast transient bur
4. models CS5 CS7 and CS9 and 450 Ibs 204 kg for model CS3 DO NOT overload the bed The combined weight of patients visitors mattress bedding and all accessories must NOT exceed rated capacity or Safe Working Load Body weight should be evenly distributed over the surface of the bed DO NOT lay sit or lean in such a way that your entire body weight is placed only on raised head or foot sections of the bed This includes when assisting the user in repositioning or transferring in or out of bed DO NOT drop the bed DO NOT allow patients to fall on the bed DO NOT jump on the bed Each of the preceding impacts can permanently damage either HI LO motor resulting in an inoperable bed In the case of an inoperable bed due to a damaged HI LO motor the HI LO motor must be replaced immediately If left unattended a damaged HI LO motor can cause the bed to fall from the highest extended position resulting in patient injury DO NOT exceed the maximum continuous duty cycle Refer to Technical Specifications NEVER allow patients to use trapeze or traction units as a total individual weight support Trapeze units are to be used only for immobilizing a patient in various traction set ups or assisting the patient in repositioning or transferring into or out of bed Entrapment Warnings A WARNING Refer to the Bed Rail Entrapment Risk Notification Guide at www invacare com If patient assessment concludes that the patient s condition increases the c
5. securely may result in injury or damage 8 1 Safety Information For Options A WARNING Refer to the Bed Rail Entrapment Risk Notification Guide at www invacare com Patient ENTRAPMENT with Assist Rail or Assist Bar may cause injury or death Mattress must fit snugly within the mattress keepers to prevent patient entrapment Use only a mattress of recommended specifications with the bed Monitor patient frequently Asses the needs of the resident prior to using the Assist Rail or Assist Bar Incorrect mounting of the assist rail or assist bar may result in patient entrapment To reduce the risk of entrapment mount the assist rail or assist bar as shown in the instructions included with the rails or bars Crush Hazard exists between assist Rail or Assist Bar and Floor at the lowest bed position Lowering the bed may cause INJURY to oneself or others Lockout the Hand Control when working near the bed and DO NOT place feet or limbs in the crush zone located beneath the Assist Rail or Assist Bar Part No 1153410 45 Invacare CS Series Beds 8 OPTIONS A WARNING Patient entrapment with bed rails assist devices or 68 Inch Rail may cause injury or death Mattress must fit snugly within the mattress keepers to prevent patient entrapment Use only a mattress of recommended specifications with the bed Monitor patient frequently Assess the needs of the resident prior to using the bed rails assist devices Incorrect mounting of
6. 0 leg section Trendelenburg or reverse trendelenburg te 0 to 14 Optional when configured Under bed clearance for 3 of bed 4 in 356 mm centered Part No 1153410 23 Invacare CS Series Beds 5 TECHNICAL DATA Electrical Specifications ess es7 je Tempa Control box mains voltage 20V or 20V or 20V or Control box input current 3 5A max 3 5A max 3 5A max 1 5A max 1 5A max 1 5A max for 230V for 230V for 230V models models models Control box current frequency 60 Hz 50 60 Hz 50 60 Hz 50 Hz for 230 Hzfor230V Hz for 230 V models models V models Control box output voltage 24 VDC 70W max Control box duty cycle 10 Max 2 min ON 18 min OFF Motorized linear head actuator linear head actuator 24 Volts DC Motorized linear actuators Leite ne foot and HI LO 24 Volts DC Six button hand pendant not available Eigh hand d h s and pendant with contour standard 10 button optional Attendant control panel Attendant control panel ACP optional Invacare CS Series Beds 24 Part No 1153410 5 TECHNICAL DATA Safety Features Built in battery back up optional not available standard with Trendelenburg 24V DC 9 2 Amps Security Pendant Lock Out CS3 CS5 CS7 CS9 CS9FX600 Pendant connection from either side standard of bed ACL attendant control lock out pendant HI LO function lock out Individual p
7. 36 in 39 in m me largeur 90 97 5 ou 105 cm Pour l utilisation d une t te de lit avec le mod le CS9FX600 vous devez utiliser la t te de or 42 in If using a head board with the CS9FX600 model bed an adjustable head board model IHBEADJ must be used lit r glable de mod le IHBEADJ La t te de lit doit tre de m me largeur que le lit Suivez les instructions du fabricant pour le Headboard must be set for the same width as the bed Follow the manufacturer s instructions for adjusting bed and head f EX r glage du lit et de la t te de lit Le matelas doit s adapter l encadrement et aux longs pans et s adapter correctement aux board Mattress must fit bed frame and side rails and assist devices snugly to prevent patient entrapment Read and O dispositifs pour viter le coincement du patient Il est important de lire et de comprendre le manuel de l utilisateur avant understand the User Manual prior to using this equipment ICCI manuals are available at www invacare cc com or your d utiliser cet quipement Vous trouverez les manuels ICCI sur le site www invacare cc com ou chez votre d taillant dealer Part No 1158523 Rev B L activation du d gagement de CPR peut causer des dommages au Activation of the CPR release may cause attendant or resident patient ou l aide Utilisation avec prudence Employer le d gage injury Use with Caution Use the CPR release only for ment de CPR pour des urgences seulement Cette fonction apporte
8. E head post screws in the bracket slots screws into the bracket slots slots Guide the key through the small bracket hole The key is attached to the bed bracket with a lanyard Invacare S CS Series Beds Foot end shown NOTE Some models only have one connection Turn and lock the key once it is fully inserted 7 Attach the cables from the foot end board to the Repeat on the other side then the opposite bed bed cables ACP cable and pendant coupling end securing both mounting points on each Tighten the nut board ACP bed only Part No 1153410 7 USAGE 7 Usage 7 1 Hand Control Pendant Operation A CAUTION CRUSH Hazard DO NOT place feet under the frame when lowering the bed 3 Function Pendant A NAN YA N Na Raise Lower Head Bed Raise Lower Knee FIGURE 3 Function Pendant Part No 1153410 37 Invacare CS Series Beds 7 USAGE 4 Function Pendant Alternate Pendants Knee CEA pen Sal Sy rai es PT Nurse AN Under eq Cal SAVE v the Bed i y r Light Raise Lower Raise Lower Bed Head and Knee FIGURE 2 4 Function Pendant Invacare CS Series Beds 38 Part No 1153410 7 USAGE 1 2 Pendant Storage and Location A DANGER Electrical SHOCK Hazard Before working on any electrical part such as the 9 pin pendant coupling ensure the main power to the bed is disconnected and the capacitor inside the co
9. FX600 Model CS9FX600 A Fold the mattress keeper around the bed in the rod The matt 76 in Bed Only With a 7 16 in socket wrench deck and the head deck and 7 16 in wrench loosen and remove the bed 80 in bed position shown end bracket fasteners 76 in Bed Only Remove the fasteners onthe 7 76 in Bed Only Slide the bed end bracket in the 8 76 in Bed Only Reinsert the bed end bracket bed end bracket mounting channel Align the hole in the bracket fasteners with the channel hole Invacare CS Series Beds 34 Part No 1153410 6 SET UP All Models Except CS9FX600 Model CS9FX600 9 76 in Bed Only Tighten the fasteners with two 10 Position the mattress on the deck 7 16 in wrenches Reposition the other three Press the mattress inside the mattress keeper Ensure the mattress is engaged on all four corners brackets and reapply the ends Install Head and Foot Ends Head and foot ends are normally packaged together either in a cardboard box or on a wooden skid separate from the bed Bed end model IHBEADJ must be used with bed model CS9FX600 Refer to Adjusting the Head Board Width for CS9FX600 on page 62 Part No 1153410 35 Invacare CS Series Beds 6 SET UP Remove the key from the _ Position Head End next to the 3 Slide the boards down while plate 4 Position Foot End next to the foot keyhole head board bracket Hook the post screws are in the bracket board brackets Hook the board padan PEE P
10. Invacare CS Series Beds CS3 CS5 CS7 CS9 CSIFX600 User Manual EN For more information regarding bed rail safety refer to the Bed Rail Entrapment Risk Notification Guide at www invacare com This manual MUST be given to the user of the product BEFORE using this product read this manual and save for future reference Yes you can 2012 Invacare Corporation All rights reserved Republication duplication or modification in whole or in part is prohibited without prior written permission from Invacare Trademarks are identified by and All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted Sherwin Williams is a registered trademark of Sherwin Williams Invacare CS Series Beds 2 Part No 1153410 CONTENTS GENERAL 5 SMOG veces PEN E V EE EAN N A NN rl nn APA ed paie ete ee sd ad A AN A AAN 5 Fimited YYarranty as Rn A giga 7 2 SAFETY 8 General Guidelines bm ena nu da Nu nana eee ies 8 Operation IN ON MATIONESS RB brin rente aa 9 EMIInformati On Ra rit ee Une nel ue RE mOn 14 3 EMC INFORMATION 16 Electromasnetic Compatibility EMC Information Asesmen NN NN BN nun l6 4 PRODUCT LABELING 21 5 TECHNICAL DATA 23 WY PICA Produsen Para Stem na 23 Mares SD CITICA IONS RS tae a NB UII BB BBB 28 6 SET UP 29 Unpacking InstrUctiOnS ca koes estas ana ana NN NN nm nun na 29 Assem Diy VS EL ICEL ON Sea ae Aa Ega ia sia 32 7 USAGE 37 Hand Controle Pendant
11. N THE HAND PENDANT INITIATE ACTION TO THE ENTIRE MATTRESS SUPPORT PLATFORM HILO INITIATE ACTION TO HEAD SECTION OF MATTRESS SUPPORT PLATFORM TOGGLE SWITCH FOR ONE TOUCH HEAD AND KNEE FOOT RAISE OPERATION INITIATE ACTION TO THE KNEE FOOT SECTION OF THE MATTRESS SUPPORT PLATFORM UP CONTROL RAISE THE CORRESPONDING SECTION OF THE MATTRESS SUPPORT PLATFORM DOWN CONTROL LOWER THE CORRESPONDING SECTION OF THE MATTRESS SUPPORT PLATFORM a Reverse Trendelenburg Pr Function A A BBEPS General warning symbol ISO 3864 Danger electricity electrical hazard symbol IEC 61310 ISO 3864 Explosive material explosion hazard symbol IEC 61310 Flammable material symbol IEC 61310 Crush hazard symbol based on ANSI Z535 Crush hazard symbol based on ANSI Z535 Crush hazard symbol based on ANSI Z535 Drop Fall Hazard symbol based on IEC 61310 Part No 1153410 GENERAL 1 2 Limited Warranty PLEASE NOTE THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4 1975 This warranty is extended only to the original purchaser who purchases this product when new and unused from Invacare Continuing Care Inc ICCI or a dealer This warranty is not extended to any other person or entity and is not transferable or assignable to any subsequent purchaser or owner Coverage under this warranty will end upon any such subsequent sale or other transfe
12. NGER Possible fire hazard when used with oxygen administering equipment other than nasal or masked type Use masked or nasal type oxygen administering equipment only in conjunction with the manual electric bed The use of any other type of oxygen administering equipment can result in a fire hazard When using nasal or masked type oxygen administering equipment the oxygen or air tubing MUST be routed and secured properly to ensure that the tubing does not become entangled and or severed during normal operation of manual electric bed Part No 1153410 LI Invacare CS Series Beds 2 SAFETY Explosion Hazard DANGER EXPLOSION Hazard DO NOT operate this bed in the presence of a flammable anaesthetic mixture with air or with nitrous oxide DO NOT use near explosive gases Keep the product a minimum of 12 away from any direct heat source Electrical and Grounding A DANGER NEVER operate if the unit has a damaged cord or plug If it is not working properly call a qualified technician for examination and repair Keep all electrical cords away from heated or hot surfaces Ensure all cables and cords are routed such that they will not become entangled or pinched Otherwise damage or injury may result If grounding is not reliable unplug the bed and use the battery power if equipped DO NOT unplug power cord from control box The pendant and power cords must be routed and secured properly to ensure that the cords DO NOT become entangle
13. Operation seen es en A en ne 37 Pendant SCOP ACS INC OCA COM ne en NN Emma 39 Power COPASIOPAR aa AN BBB Bia 4 Raisevand Lower the Feel Life Rateh et nana esas tas aan NN E EE EE E anna 42 Foot Fad Lock Mechanism on CS3 Beda mena E E EN SN 43 B d St er MEchani SIN enim e E E a A EN T E E TR N 44 Part No 1153410 3 Invacare CS Series Beds CONTENTS 8 Invacare S CS Series Beds OPTIONS Safety Information For Options Bed Rails and Positioning Devices Other Accessories ta Kania AAN EN BNN Optional Drainage Bag Holder Optional Touch up Paint Optional Attendant Control Panel Operation Optional Trendelenburg and Reverse Trendelenburg Attendant Control Panel Pendant HI LO Lock Out Optional Optional Cardiopulmonary Resuscitation CPR Release Optional 39 Inch and 42 Inch Wide Decks Adjustable Width Bed Model CS9FX600 MAINTENANCE Cleaning Instructions Annual Maintenance Check Quarterly Maintenance Check Environmental Conditions for Storage and Transport Environmental Conditions for Operation 10 TROUBLESHOOTING Part No 1153410 GENERAL General I 1 Symbols Warnings Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage See the information below for definitions of the signal words DANGER Danger indicates an imminently hazardous situation which if not avoided will result in death or serious injury WARNING Warning ind
14. R VIOLATIONS OF ANY WARRANTY WHATSOEVER SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PERSUANT TO THE TERMS CONTAINED HEREIN THE APPLICATION OF ANY IMPLIED WARRANTY WHATSOEVER SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN ICCI SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER Part No 1153410 7 Invacare CS Series Beds 2 SAFETY 2 Safety The Safety section contains important information for the safe operation and use of this product 2 1 General Guidelines A DANGER RISK OF INJURY OR DEATH Use ONLY Invacare rails mattresses bed extenders and other accessories with Invacare bed products Bed accessories designed by other manufacturers have NOT been tested by Invacare Use of NON Invacare bed accessories may result in injury or death WARNING DO NOT use this product or any available optional equipment without first completely reading and understanding these instructions and any additional instructional material such as owner s manuals service manuals or instruction sheets supplied with this product or optional equipment If you are unable to understand the warnings cautions or instructions contact a healthcare professional dealer or technical personnel before attempting to use this equipment otherwise injury or damage may occur The initial set up of this bed must be performed by a qualified technician Procedures other than those described in
15. TION Risque d ecrasement lors de l utilisation de Trendelenburg Invers e Un point de Crush Hazard when using Reverse Trendelenburg Pinch point exists between the pincement existe entre le pied de lit et la terre la position plus basse L abaissement Footboard and the floor at the lowest position Lowering of the foot end may cause du pied de lit peut causer des blessures a soi m me ou a autrui Ne PAS placer les A dr Ais 5 1 injury to oneself or others Do not place feet or limbs in the crush zone located piocs jambes ou oras dans ia oe crasoment situ e sous le pled de Ih Se reporter 1156582 beneath the Footboard Refer to the Product Manual prior to operating the bed Invacare CS Series Beds 22 Part No 1153410 5 TECHNICAL DATA 5 Technical Data 5 1 Typical Product Parameters Certifications All models 120 V models CS3 CS5 CS7 CS9 CS9FX600 and 230 V models CS5 CS7 CS9 conform to UL60601 1 and IEC60601 Certified to IEC60601 2 38 and IEC60601 1 2 and CAN CSA C22 2 No 601 1 230 V models CS5 and CS7 are CE marked for Australia and New Zealand Elevation Range floor to deck Stability Range 8 4 to 26 2 in casters locked or off casters 211 to 686 9 to 30 in 7 to 30 in 545505 mm 229 to 178 to 762 LA 229 to 762 mm Mobility range on casters 8 4 in 211 mm 762 mm mm only Angle between back section head deck 0 to 70 and deck platform Angle between back section and upper gt 9
16. and floor is created when lowering the bed to the lowest position Keep feet clear of bed when lowering bed Close supervision is necessary when this product is used near or by children or people with disabilities DO NOT let any individual underneath the bed or in between the raised bed frame components at any time WARNING This product has been supplied from an environmentally aware manufacturer that complies with the Waste Electrical and Electronic Equipment WEEE Directive 2002 96 CE This product may contain substances that could be harmful to the environment if disposed of in places landfills that are not appropriate according to legislation Please be environmentally responsible and recycle this product through your recycling facility at its end of life Part No 1153410 15 Invacare CS Series Beds 3 EMC INFORMATION 3 EMC Information 3 1 Electromagnetic Compatibility EMC Information Medical Electrical Equipment needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided in this manual Portable and mobile RF communications equipment can affect medical electrical equipment A WARNINGS The use of accessories tranducers and cables other than those specified by the manufacturer may result in increased emissions or decreased immunity of this bed This bed should not be used adjacent to or stacked with other equipment and that if adjacent or stacked use
17. are S CS Series Beds 7 USAGE 1 4 Raise and Lower the Heel Lift Ratchet With knee foot platform adjusted to the The foot section can rest at any of the six 3 Slowly lower the platform to engage the highest position lift the foot panel pre set stops nearest stop T TK 4 The platform cannot lower past the nearest 5 To reset the ratchet mechanism raise the 6 At the lowest position the deck can once stop while being adjusted platform to the highest level then lower the again be raised to the desired stop platform in one motion Invacare CS Series Beds 42 Part No 1153410 7 USAGE 7 5 Foot Pad Lock Mechanism on CS3 Bed A CAUTION Moving the bed while the floor lock caster lock or foot pad is engaged may DAMAGE the bed DO NOT move the bed unless the floor lock caster lock or foot pad is disengaged unlocked Mobility Stability Range Bed at the Lowest Position FIGURE 3 Foot Pad Lock Mechanism on CS3 Bed Part No 1153410 43 Invacare CS Series Beds 7 USAGE 7 6 Bed Steer Mechanism 74 he gt Steer mechanism is on either side of the With the locking wheel tab facing outward 3 When engaged the bed will steer easily head end of the bed flip the steer mechanism Invacare CS Series Beds 44 Part No 1153410 8 OPTIONS 8 Options A WARNING After ANY adjustment repair or service and BEFORE use make sure that all attaching hardware is tightened securely Failure to tighten hardware
18. bligation and your exclusive remedy under this warranty shall be limited to such repair and or replacement For warranty service please contact the dealer from whom you purchased your ICCI product In the event you do not receive satisfactory warranty service please write directly to ICCI at the address on the back cover provide dealer s name address and the date of purchase indicate nature of the defect and if the product is serialized indicate the serial number Do not return products to our factory without our prior consent LIMITATIONS AND EXCLUSIONS THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED PRODUCTS SUBJECTED TO NEGLIGENCE ACCIDENT IMPROPER OPERATION MAINTENANCE OR STORAGE PRODUCTS MODIFIED WITHOUT ICCI S EXPRESS WRITTEN CONSENT INCLUDING BUT NOT LIMITED TO MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT OF ICCI OR TO A PRODUCT DAMAGED BY CIRCUMSTANCES BEYOND ICCI S CONTROL AND SUCH EVALUATION WILL BE SOLELY DETERMINED BY ICCI THE WARRANTY SHALL NOT APPLY TO NORMAL WEAR AND TEAR OR FAILURE TO ADHERE TO THE PRODUCT INSTRUCTIONS THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES WHATSOEVER WHETHER EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE AND THE SOLE REMEDY FO
19. come wet or submerged DO NOT operate the bed if the cord or outlet is damaged DO NOT operate the bed if any motor has malfunctioned or is damaged in any manner DO NOT use this bed in Active Treatment Ether Environments Plug the three prong electrical cord ONLY into a properly grounded 110 VAC to 120 VAC 60 cycle outlet that is rated to at least six amps This electric bed must be grounded In the event of a malfunction or breakdown grounding provides a path of least resistance for electric current thereby reducing the risk of electric shock This product is equipped with a cord having an equipment grounding conductor and a grounded plug The plug must be inserted into an appropriate electric outlet that is properly installed and grounded in accordance with all local codes and ordinances A CAUTION A safety feature of this product includes protection against overheating caused by excessive or extended periods of operation Depending on the duration this includes multiple or repeated adjustments or the use of multiple functions at one time To assure trouble free operation ALWAYS allow a slight pause between multiple adjustments and avoid pressing more than one function button at a time If thermal protection activation should occur the bed will not respond to pendant commands Given this situation release the pendant button and allow the bed unit to sit for several minutes This will allow the protection function time to reset and r
20. d pinched and or severed during operation of the electric bed NEVER operate the unit if these cords are damaged Refer servicing to qualified personnel only Grounding reliability depends upon a properly grounded wall outlet Improper connection of the equipment grounding conductor can result in electrocution Check with a qualified electrician or service person if you are doubtful that the electrical outlet is properly grounded DO NOT modify the grounding plug provided If it will not fit into the electrical outlet have a proper outlet installed by a qualified electrician Grounding reliability can only be achieved when connected to an equivalent receptacle marked Hospital Only or Hospital Grade In the event of a power outage the bed can be powered by its internal battery but MUST remain plugged into the grounded outlet for proper grounding Electric components such as motors may cause severe injury including electrocution if exposed to water During routine bed operation or when cleaning DO NOT expose electrical components to water Unplug and de energize electrical components when water products are near these components Invacare CS Series Beds 12 Part No 1153410 2 SAFETY A WARNING To de energize the bed it must be unplugged from the wall outlet and the battery must be disconnected from the controller to prohibit operation DO NOT use an extension cord DO NOT permit the cord wall outlet motors control box or pendant to be
21. diated RF disturbances are controlled The customer or the user of the CS Bed can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and the CS Bed as recommended below according to the maximum output power of the communications equipment Rated maximum output power of Separation distance according to frequency of transmitter transmitter m 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2 5 GHz d 2 3 JP For transmitters rated at a maximum output power not listed above the recommended separation distance d in metres m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer NOTE At 80 MHz and 800 MHz the separation distance for the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people Invacare CS Series Beds 20 Part No 1153410 4 PRODUCT LABELING 4 Product Labeling AVERTISSEMENT WARNING On Both Sides of Bed Un patient peut tre bless ou m me mourir s il est coinc Les huit sections de plateformes ajustables DOIVENT tre de Patient entrapment may cause injury or death All eight adjustable deck sections MUST be set to the same width
22. ed always lock the locking caster s Inspect the wheel locks for correct locking action before actual use Even with casters properly locked some flooring surfaces such as tile or wood will allow the bed to move under some conditions Use on surfaces such as these must be evaluated by the care provider After any adjustments repair or service and before use make sure all attaching hardware is tightened securely If a liquid is spilled in or around the electric bed unplug the electric bed before cleaning Clean up the spill and allow the electric bed or the area around the electric bed to dry thoroughly before using the electric controls again When operating moving electric beds always ensure that the individual utilizing the bed is positioned properly within the confines of the bed DO NOT let any extremities protrude over the side or between the bed rails when performing these functions Hang pendant on hook or secure with linen clip when not in use Keep cord clear of moving parts DO NOT roll the bed over the power cord or pendant cord DO NOT entangle the cords on other objects A pinched electric cord is dangerous and can become damaged Use the Power Cord Strap when moving the bed Refer to Pendant Storage and Location on page 39 and Power Cord Storage on page 41 Part No 1153410 9 Invacare CS Series Beds 2 SAFETY Weight Limitation A WARNING This bed is rated to 600 Ibs 272 kg for model CS9FX600 500 Ibs 228 kg for
23. ed Deck View PI H It Invacare S CS Series Beds 39 in Width Side View Adjustable Deck Adjustment Knob Snap Button Top Bed Deck View Se U I a Se 60 42 in Width Side View Adjustable 42 In Deck Wing Adjustment Adjustment Knob Snap Button Top Bed Deck View CI TU I Y SI H El y e Part No 1153410 Loosen the knob securing the adjustable deck wing Depress the snap button Slide the adjustable deck wing in or out to the desired position Ensure the snap button snaps into the appropriate adjustment hole Tighten the knob to secure the adjustable deck wing Se a ee a Repeat STEPS to 6 for each section until they are all adjusted to the same width Part No 1153410 61 Adjust the head board width Refer to Adjusting the Head Board Width for CS9FX600 on page 62 8 OPTIONS Invacare S CS Series Beds 8 OPTIONS Adjusting the Head Board Width for CS9FX600 Bed end model IHBEADJ is intended for use on bed model CS9FX600 The head board is adjustable and ships in the position for a 36 in wide bed Left Board Wing 42 in 39 in Center Section Knobs Firmly grasp one of the board wings While holding the board wing remove the knobs securing that wings to the center section Move the board wing until the mounting holes line up with the desired adjustment holes in the center section Install the knobs to secure the board wing in the desired posi
24. endant function lock out es on ACP j optional Part No 1153410 25 Invacare CS Series Beds 5 TECHNICAL DATA Dimensions and Weight engi vera ee Length Betweenteadandfootends Length maresspatorm Width mages larme ie with assist rails 36 in standard 39 in 997 mm Invacare CS Series Beds 26 Part No 1153410 5 TECHNICAL DATA Width with Thinksoft positioning devices 36 in Standard 39 in Wide 42 in Wide Weight 36 in Standard Deck 190 Ib 86 kg 39 in Wide Deck 196 Ib 89 kg 200 Ib 91 kg 42 in Wide Deck 199 Ib 90 kg 203 Ib 92 kg not available CS9FX600 Adjustable Deck N A 206 Ib Load capacity safe working load 450 Ib 204 kg 500 Ib 227 kg 600 Ib 272 kg 39 in or 42 wide bed deck optional Hana Not compatible with 68 inch rail Adjustable Deck Standard Not Available Not compatible with 68 inch rail 41 4 in 1048 mm 44 4 in 1124 mm 47 in 1200 mm not available not available Part No 1153410 21 Invacare CS Series Beds 5 TECHNICAL DATA 5 2 Mattress Specifications A WARNING Possible patient ENTRAPMENT Hazard if using non specified mattress Refer to the Bed Rail Entrapment Risk Notification Guide at www invacare com Use only a mattress of recommended specifications with this bed A mattress may not be included with this bed It is highly recommended that you use an Invacare branded mattress that is designed to confo
25. er s Declaration Electromagnetic Immunity Power frequency 50 60 Hz 3 A m 3A m Power frequency magnetic fields should be at levels characteristic of magnetic field IEC 61000 4 8 a typical location in a typical commercial or hospital environment NOTE Uris the a c mains voltage prior to application of the test level Guidance and Manufacturer s Declaration Electromagnetic Immunity The CS Bed is intended for use in the electromagnetic environment specified below The customer or the user of the CS Bed should assure that it is used in such an environment Immunity Test IEC 60601 Compliance Electromagnetic Environment Guidance Test Level Level Portable and mobile RF communications equipment should be used no closer to any part of the CS Bed including cables than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter Recommended separation distance 3 Vrms Conducted RF 150 kHz to 80 IEC 61000 4 6 MHz 3 Vrms d 1 2 P Invacare CS Series Beds 18 Part No 1153410 3 EMC INFORMATION Guidance and Manufacturer s Declaration Electromagnetic Immunity Radiated RF 3 V m _ IEC 61000 4 3 80 MHz to 2 5 d 1 2 JP 80 MHz to 800 MHz GH d 2 3 JP 800 MHz to 2 5 GHz where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer and d is the recommended separation distance in metres m Field strengths from fi
26. estore bed function Depending on the severity of the initial overheating this could take up to 30 minutes Part No 1153410 13 Invacare CS Series Beds 2 SAFETY Battery A WARNING Charge battery through the controller NEVER attempt to charge the battery by any other means Internal battery should be tested monthly 2 3 EMI Information CAUTION IT IS VERY IMPORTANT THAT YOU READ THIS INFORMATION REGARDING THE POSSIBLE EFFECTS OF ELECTROMAGNETIC INTERFERENCE ON THIS PRODUCT Electromagnetic Interference EMI From Radio Wave Sources This product may be susceptible to electromagnetic interference EMI which is interfering electromagnetic energy EM emitted from sources such as radio stations TV stations amateur radio HAM transmitters two way radios and cellular phones The interference from radio wave sources can cause the powered bed to release its brakes move by itself or move in unintended directions It can also permanently damage the powered bed s control system The intensity of the interfering EM energy can be measured in volts per meter V m Each powered bed can resist EMI up to a certain intensity This is called its immunity level The higher the immunity level the greater the protection At this time current technology is capable of achieving at least a 20 V m immunity level which would provide useful protection from the more common sources of radiated EMI There are a number of sources of relatively in
27. h CS Bed kit on a bed that is equipped with the Trendelenburg and Reverse Trendelenburg feature Risk of FALL when Assist Bar is UNLATCHED Assist Bar may rotate quickly and drop to the next locked position causing the patient to lose their balance and fall Ensure the Assist Bar is fully latched in down position after each use Check that the Assist Bar is locked before leaving a patient unattended Never use the Assist Bar as a Rail If necessary the head and foot end board position can be adjusted in order to meet FDA guidelines Refer to the section titled Install the Mattress Keeper Rod to the Head and Foot Decks for detailed instructions on adjusting the end board bracket location A Part No 1153410 47 Invacare CS Series Beds 8 OPTIONS 8 2 Bed Rails and Positioning Devices The listed bed rails and positioning devices are available MODEL DESCRIPTION CRIA IHCSBARS CS Assist Bar Set IHCSTSPD ThinkSoft Positioning Device TSPD Think Perma Dere T0 8 3 Other Accessories The listed items are available as optional accessories MODEL DESCRIPTION IHCSBEK 4 Inch Extension Kit IHCSDB Drainage Bag Holder IHCSPD Aftermarket Pan Deck Kit Invacare CS Series Beds 48 Part No 1153410 8 OPTIONS 8 4 Optional Drainage Bag Holder 8 5 Optional Touch up Paint Sherwin Williams 5A 58147 00 A CODE 82X WHITE BIRCH 2nd Dimension 5 0 Acrylic Enamel This product can be purchased at Sherwin Wi
28. hance of entrapment the bed MUST be in the flat position when left unattended Invacare CS Series Beds 10 Part No 1153410 2 SAFETY Repair or Service Information A DANGER After any adjustments repair or service and before use make sure all attaching hardware is tightened securely DO NOT open assemblies such as the motors pendant control boxes or gearboxes No user serviceable parts are inside Only qualified technicians are permitted to repair these parts If unqualified individuals perform any work on these beds the warranty is void Unplug the power cord from its power source before performing any maintenance on the electric bed DO NOT unplug the power cord from the control box Damage to cord will result The control box is mounted to the head motor with a cable tie If replacing the control box remove the cable tie and slide the control box away from the head motor until it is free Disconnect all cable connections Before connecting disconnecting the connections at the control box make sure the cable lock is removed by lightly depressing on the end tabs and lifting After connectors are plugged in route all cables into the cable lock slots and snap the cable lock in place When installing any connectors into the control box be sure the cable lock is secure after installation otherwise injury or damage may occur DO NOT force the connector into the control box otherwise injury or damage may occur Fire Hazard DA
29. head deck Part No 1153410 55 Invacare CS Series Beds 8 OPTIONS KIS CPR handle is at the foot of the bed 2 Grip the CPR handle at the foot end 3 A second person is recommended of bed to gently lower the head deck E i Foot end not shown for clarity 4 Once the CPR handle is squeezed the head deck will drop rapidly Invacare CS Series Beds 56 z r sae j D VA Squeeze the CPR handle to drop the head deck Part No 1153410 8 OPTIONS 8 10 Optional 39 Inch and 42 Inch Wide Decks A WARNING Possible patient ENTRAPMENT Hazard if using non specified mattress on a wide bed Mattress must fit snugly between appropriate mattress keepers and properly sized head and foot ends that are designed for use on wide beds Use only a mattress of recommended specifications with this bed DO NOT use a mattress extension pad Refer to Technical Data on page 23 The following bed options are not compatible with the 39 inch or 42 inch wide bed deck 68 inch rail The CS bed is available with wider decks for resident comfort Both 39 inch wide deck and 42 inch wide decks are factory installed options 39 in or 42 in Nominal FIGURE 5 Optional 39 Inch and 42 Inch Wide Decks Part No 1153410 57 Invacare CS Series Beds 8 OPTIONS 8 11 Adjustable Width Bed Model CS9FX600 A WARNING Possible patient ENTRAPMENT Hazard if using non specified mattress on an adjustable bed Mattress must fit sn
30. hildren and ETL Lab el _ 2 3 O V CS 5 CS7 57 l encadrement et assurez vous qu aucun enfant ou pets are not under or near the frame before y lowering the bed Beware of PINCH POINTS animal ne se trouve sous ou pres de l encadrement du lit avant de I abaisser Faites attention aux POINTS below deck panels next to fixed attachments DE PINCEMENT situ s sous les panneaux pres des and between moving parts fixations d accessoires et entre les pieces mobiles 1158522 Rev A On Both Sides All labels applied to bed frame except where noted of Bed Part No 1153410 21 Invacare CS Series Beds 4 PRODUCT LABELING CAUTION KEEP SWITCH CORD CLEAR OF MOVING PARTS PLACE IN HOLDER WHEN NOT IN USE This hand contro pendant can be located on either side of the bed by connecting into either of the connectors located under the left and right side frame When supplied the pendant holster provides convenient pendant storage for the resident and attendant when the pendant is not in use The holster must be snapped on the outside of the rail with the backside facing the mattress to prevent possible interference For resident access the pendant may be attached to bedding using the linen clip provided When pendant access is limited to the attendant the pendant can be stored behind the headboard using the Velcro strips provided Optional Foot End Board ACP with Trendelenburg ATTENTION A A CAU
31. icates a potentially hazardous situation which if not avoided could result in death or serious injury gt gt D CAUTION Caution indicates a potentially hazardous situation which if not avoided may result in property damage or minor injury or both IMPORTANT Indicates a hazardous situation that could result in damage to property if it is not avoided Gives useful tips recommendations and information for efficient trouble free use Part No 1153410 5 Invacare CS Series Beds GENERAL Symbols used on the CS Bed G gt D IPX4 R CLASS I WTERTE MD LISTED PROTECTIVE CONDUCTOR TERMINAL EQUIPOTENTIALITY WARNING SAFE WORKING LOAD THE MAXIMUM ALLOWABLE LOAD ON EQUIPMENT IF THE INSTRUCTIONS FOR INSTALLATION AND USE ARE FOLLOWED ALTERNATING CURRENT ON SUPPLY OFF SUPPLY INTERNATIONAL PROTECTION CODE 04 PROTECTION AGAINST WATER SPRAY FROM ANY DIRECTION APPLIED PART TYPE B EQUIPMENT EQUIPMENT CLASSIFICATION IN TERMS OF PROTECTION AGAINST ELECTRICAL SHOCK Intertek s ETL Listed Mark for US and Canada A product bearing the ETL Listed Mark is determined to have met the minimum requirements of prescribed product safety standards Battery Charging Yellow LT on Trend ACP Battery Fully Charged Green Invacare CS Series Beds Trendelenburg Lift with Two Persons based on ISO 3864 FUNCTION LOCK OUT ACTIVATE TOGGLE SWITCH TO DENY FUNCTION ACCESS O
32. il Guidelines are met use ONLY the 84 inch CS bed kit with a mattress that is 84 inch 2137 mm long An 80 inch mattress with a 4 inch extension pad MUST NOT be used in any circumstance Mattress MUST fit bed frame and assist rails snugly to reduce the risk of entrapment Invacare CS Series Beds 46 Part No 1153410 8 OPTIONS WARNING Safe Working Load of the Standard Trapeze is 168 lb 750 N DO NOT exceed 168 Ib 750 N Safe Working Load of Heavy Duty Trapeze is 250 Ibs 1115 N DO NOT exceed 250 Ib 1115 N A PINCH SQUEEZE point exists between the head deck and the side rails To avoid INJURY keep arms and other appendages away from the openings in the side rails and the upward moving head deck CAUTION Contact between the floor and the Assist Rail may cause the bed to become UNSTABLE An unstable bed may tilt from horizontal and or drop suddenly causing property DAMAGE or personal INJURY Before lowering the bed ensure the Assist Rail is NOT in the TRANSFER position INJURY from patient falls may occur even when operating the side rails as instructed Place the bed in the lowest position to minimize the risk from falls gt pp gt The trapeze bar may damage walls and ceilings when used with the Trendelenburg feature Invacare recommends removing the trapeze when using the Trendelenburg function DO NOT install an 84 Inch CS Bed kit on a bed that is equipped with the CPR release feature DO NOT install an 84 Inc
33. lliams Automotive paint branches only Part No 1153410 49 Invacare CS Series Beds 8 OPTIONS 8 6 Optional Attendant Control Panel Operation 3 Function Pendant Attendant Control Panel Lockout CE 14 14 FIGURE 3 Function Pendant Invacare CS Series Beds 50 Part No 1153410 8 OPTIONS 4 Function Pendant Using the integrated Nurse Call Feature Locate call cord cable at the head of the bed along with the power cord 2 Route cable to nurse call wall outlet and insert call cable plug into socket A WARNING Extra cable should be routed and secured to bed to prevent tripping hazards Otherwise injury may occur CAUTION Route cable and secure to bed avoiding all pinch points Otherwise damage to the cable and bed will occur 3 Coil any extra cable and secure to the bed 4 Test Nurse Call by pressing the red first aid button on the hand pendant In the event of a power failure or an issue occurs within the electronic system of your Invacare bed the nurse call button will be activated and will not be reset until the electronic system is running properly Remove the nurse call plug to disable nurse call signal until service is preformed Using the Underbed Light The underbed light has pre installed at the foot end of the bed All cabling has been routed and secured to keep it from getting pinched during normal operation of the bed Part No 1153410 5 Invacare CS Series Beds 8
34. nt Guidance to Reduce Entrapment published by the U S Department of Health and Human Services Food and Drug Administration Inspect the covering of the bed s control panel and the patient control panel to assure that the covering is not cracked or damaged Inspect for damaged or loose wiring Have a qualified technician replace any frayed or damaged cords Inspect for secure grounding Inspect rail latches Ensure that all rails engage and lock as specified Inspect rails for wear and damage and replace as required Lubricate rail pivot points as needed with white lithium grease Inspect bed rails Assist Rails or Assist Bars for the presence of tubing end caps and replace as required Tighten adjust or replace any parts or bolts etc that are loose or show signs of wear Lubricate all mechanical hinge points bushings and surface contact points with white lithium grease Inspect for wear on clevis pins and hitch pins and replace if worn or missing Inspect the rails for noticeable scratches and chips Use a matching enamel touch up paint to retouch if necessary Refer to Options for paint specification Quarterly Maintenance Check Unplug bed from wall outlet and verify battery function if equipped Battery may be built in or portable Environmental Conditions for Storage and Transport Store and or transport the bed in a clean and dry environment with an ambient temperature range between 10 and 50 Celsius 0 to 125 F E
35. ntrol box is fully discharged Full capacitor discharge can be achieved by sequentially depressing the Up and Down buttons on the hand pendant at least 20 times after main electrical power to the control box is cut Ensure the hand pendant is not locked out when discharging it Place the pendant holster between the top 2 Slide the pendant into the holster Alternatively use the pendant clip to rail bars secure the pendant to bed linen Part No 1153410 39 Invacare CS Series Beds 7 USAGE 4 The pendant can also be attached to the To move the pendant to the other side of 6 Remove the cable end from the Y cable back of either side of the Head end the bed disconnect the main power then housing unscrew the coupling cap on the pendant cable 7 On the other side of the bed remove the 8 Align arrows then insert the pendant cable 9 Screw the coupling cap to the threaded Y cap from the Y cable housing Replace the end into the Y cable housing cable housing end cap on the other side of the bed Invacare CS Series Beds 40 Part No 1153410 7 USAGE 1 3 Power Cord Storage Disconnect the main power cable from the wall outlet and store the power cord when the bed is not in use Secure the power cord to the back of the head end with the hook and loop strap when moving the bed 2 Excess power cord can be secured to the back of head end with the hook and loop strap Part No 1153410 4l Invac
36. nvironmental Conditions for Operation Bring the bed to a Safe Operating Temperature between 5 and 40 Celsius 41 and 100 F before operating the bed Invacare CS Series Beds 64 Part No 1153410 10 TROUBLESHOOTING 10 Troubleshooting A WARNING Read all general guidelines warnings and cautions before performing any repair maintenance on the bed All repair and maintenance on the bed should be performed by a qualified technician Unplug the power cord from its power source before performing any maintenance on the electric bed DO NOT unplug the power cord from the control box Damage to cord will result EFFECT POSSIBLE CAUSE VERIFICATION CORRECTIVE ACTION Bed does not stay in Floor lock not engaged Green plunger on floor lock postis Activate floor lock green plunger should NOT be place visible visible Insufficient static friction Floor surface is slippery and or Clean the surrounding floor and remove loose between floor lock foot foreign membrane between bumper material under the bed bumper and floor and floor Floor lock not functioning Floor lock is stuck in one position Contact Invacare Continuing Care Service Department 800 668 2337 Bed is not level Hi Lo actuators are unevenly Bed deck is not parallel with floor Raise bed to highest position extended or Lower bed to lowest position Actuator not working System Fault Flashing LEDs on ACP Bed function To Reset hold the pendant bed up and bed down
37. on port Invacare CS Series Beds 66 Part No 1153410 10 TROUBLESHOOTING EFFECT POSSIBLE CAUSE VERIFICATION CORRECTIVE ACTION Actuator not working Faulty hand control pendant Pendant cable is connected power Contact Invacare Continuing Care Service is on lock out is off and hand Department 800 668 2337 control pendant does not function Disconnect power supply then replace hand pendant with functioning unit from another bed if available Reconnect power and test Bed ends to not fit Bent brackets Visually ensure the brackets are Carefully straighten minor deformations Call Service properly parallel to the frame Department to replace significantly bent brackets 800 668 2337 Part No 1153410 67 Invacare CS Series Beds For Customer Service call 800 668 2337 Invacare Continuing Care Inc A subsidiary of Invacare Corporation For more information regarding Invacare continuing Care Inc ICCI products parts and services please visit www invacare cc com or call 800 668 2337 Part No 1153410 Rev L 3 12 Manufacturing Location 994 Hargrieve Road London Ontario Canada N6EIP5 Invacare Continuing Invacare Australia Pty Ltd Care Inc Lenton Place USA and Canada North Rocks NSW 2151 One Invacare Way Sydney Australia Elyria Ohio USA 011 61 2 8839 5333 44036 2125 www invacare cc com Yes you can
38. ot end of the bed FIGURE 4 Pendant HI LO Lock Out Optional Invacare CS Series Beds 54 Part No 1153410 8 OPTIONS 8 9 Optional Cardiopulmonary Resuscitation CPR Release A CAUTION Activation of the CPR release may cause attendant or resident injury Use with Caution Use the CPR release only for emergency situations This function will rapidly bring the head deck to a flat position Two person operation is recommended one person to release the head deck and another to hold and gently guide the head deck down DO NOT install a CS Bed Extender on a bed that is equipped with the CPR release feature PINCH POINT between rail and floor is created when lowering bed to the lowest position Keep feet clear of bed rail when lowering bed Close supervision is necessary when this product is used by or near children or people with disabilities DO NOT let any individual underneath the bed or in between the raised bed frame components at anytime Using the CPR Release When using the CPR Release function it is recommended to use two people one person to release the head deck at the foot end of the bed and another person to gently guide the head deck to a horizontal position Additional Means to Lower the Back Rest in an Emergency The clevis pin and retaining clip can be removed from the connection between the head actuator and head deck section to lower it The head deck must be supported while removing the pin and lowering the
39. r of title to any other person This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state ICCI warrants the frame and welds on this product when purchased new and unused will be free from structural defects on the frame for a period of ten 10 years electrical for a period of three 3 years and mechanical for a period of five 5 years from date of purchase from ICCI or a dealer with a copy of the seller s invoice required for coverage under this warranty ICCI warrants the frame of this product when purchased new and unused to be free from defects in materials and workmanship for a period of ten 10 years from date of purchase from ICCI or a dealer with a copy of the seller s invoice required for coverage under this warranty For all other components of this product when purchased new and unused ICCI warrants that they will be free from defects in material and workmanship for a period of one I year from date of purchase from ICCI or a dealer with a copy of the seller s invoice required for coverage under this warranty Upholstery vinyls fabrics and or laminates are not covered under this warranty If within such warranty periods any such product shall be proven to be defective such product shall be repaired or replaced at ICCI s option This warranty does not include any labor or shipping charges incurred in replacement part installation or repair of any such product ICCT s sole o
40. ra emergency situations This function will rapidly bring the rapidement le dossier une position plate L op ration pour deux F backrest to a flat position Two person operation is personnes est recommand e Une personne pour lib rer le dossier et gt recommended One person to release the backrest and another des autres la prise et pour guider doucement le dossier vers le bas to hold and gently guide the backrest down Le risque de PINCH POINT existe en guidant le dossier pendant le PINCH POINT hazard exists when guiding the backrest during d gagement de CPR Ne pas placer des mains directement entre le CPR release Avoid placing hands directly between the dossier r glable et la charpente de lit Placer les mains seulement sur adjustable backrest and the bed frame Place hands only on the l ext rieur du dossier loin de la charpente de lit outside of the backrest away from the bed frame reorder No 1152548 For Optional CPR Release On Both Sides of Bed Around Optional CPR Release Bar souepnid Dane UONESII IN Judwapidei 339 Ej ap uol 2es ej BJassiege Md op Juawabebap 04 CPR Release will lowe the head section rapidly Use with caution Serial Number Label AAVERTISSEMENT AWARNING ETL Label 20 V CS 3 y CS5 y er Co y an d Ser FX600 Risque d crasement occasionn par la ZONE DE Crush Hazard due to LOW BED CLEARANCE MARGE FAIBLE DU LIT Eloignez vous de Stay clear of frame and ensure c
41. rimmed or green tie holding 10 Carefully cut the untrimmed or green tie holding II Plug power cord into a properly grounded the pendant bundle the mains cable bundle outlet Part No 1153410 31 Invacare CS Series Beds 6 SET UP Cut the untrimmed or green tie while holding the 2 Press HI LO UP button on the hand pendant 3 Rotate the wall bumper to the floor at the head wall bumper end of the bed 6 2 Assembly Instructions Install the Mattress Keeper Rod to the Head and Foot Decks A WARNING The mattress keeper rods are an integral part of the bed rail system By securing the mattress in place the mattress keeper rods prevent unsafe gaps from forming between the bed ends or rails and the mattress Install the mattress keeper rods correctly to decrease the risk of patient entrapment The mattress keeper rods hold the mattress in place Install them in the head and foot decks Invacare CS Series Beds 32 Part No 1153410 6 SET UP All Models Except CS9FX600 All Models Except CS9FX600 All Models Except CS9FX600 IA nas bam LAM lt P J gt D LD lt TPS With the mattress keeper upright insert the 2 There are two choices for mattress keeper rod 3 Mattress keeper rod insertion on 80 in Bed rod ends into the appropriate deck holes insertion 76 in bed option shown above Part No 1153410 33 Invacare CS Series Beds 6 SET UP All Models Except CS9
42. rm to the following dimensions Named Size NamedSie Minimum Se Maimun size Wa 42 in 1067 mm 41 5 in 1054 mm 42 5 in 1080 mm 6 in 152 mm 5 88 in 149 mm 6 12 in 155 mm Invacare CS Series Beds 28 Part No 1153410 6 SET UP 6 Set Up 6 1 Unpacking Instructions A CAUTION Equipment DAMAGE may result from improper wire tie removal DO NOT cut any trimmed plastic wire ties Cut only the untrimmed plastic ties around the wood spacer All other plastic ties are used to secure the electric cables in place and should not be cut Nx Ee DR AV Steady upright bed _ Slowly lower to floor use two people if 3 Slide off end boxes and remove plastic sleeve necessary Part No 1153410 29 Invacare CS Series Beds 6 SET UP A WARNING Bed DAMAGE or personal INJURY may occur if the bed is dropped Ensure the bed is lowered slowly to the floor Use additional people if necessary Remove wood spacer from front end of bed by 5 Cut the untrimmed or green tie holding the lifting it off of bed end brackets head deck to the frame Invacare CS Series Beds 30 Part No 1153410 6 SET UP SF SX 6 Cut the untrimmed or green plastic tie holding 7 Cut the untrimmed or green tie holding the 8 Cut the untrimmed or green ties holding the the knee foot panel to the frame mattress keepers on either side of the bed mattress keepers at the end of the bed 9 Carefully cut the unt
43. st IEC 61000 4 4 Surge IEC 61000 4 5 Voltage dips short interruptions and voltage variations on power supply input lines IEC 61000 4 1 Part No 1153410 6 kV contact 8 kV air 2 kV for power supply lines kV for input output lines kV differential mode 2 kV common mode lt 5 Ut gt 95 dip in Ur for 0 5 cycle 40 Ur 60 dip in Ur for 5 cycles 70 Ur 30 dip in Ut for 25 cycles lt 5 Ut gt 95 dip in Ur for 5 sec 6 kV contact 8 kV air 2 kV for power supply lines kV for input output lines kV differential mode 2 kV common mode lt 5 Ur gt 95 dip in Ur for 0 5 cycle 40 Ur 60 dip in Ur for 5 cycles 70 Ur 30 dip in Ur for 25 cycles lt 5 Ur gt 95 dip in Ur for 5 sec Floors should be wood concrete or ceramic tile If floors are covered with synthetic material the relative humidity should be at least 30 Mains power quality should be that of a typical commercial or hospital environment Mains power quality should be that of a typical commercial or hospital environment Mains power quality should be that of a typical commercial or hospital environment If the user of the CS Bed requires continued operation during power mains interruptions it is recommended that the CS Bed be powered from an uninterruptible power supply or a battery Invacare S CS Series Beds 3 EMC INFORMATION Guidance and Manufactur
44. tense electromagnetic fields in the everyday environment Some of these sources are obvious and easy to avoid Others are not apparent and exposure is unavoidable However we believe that by following the warnings listed below your risk to EMI will be minimized The sources of radiated EMI can be broadly classified into three types Hand held Portable transceivers transmitters receivers with the antenna mounted directly on the transmitting unit Examples include citizens band CB radios walkie talkie security fire and police transceivers cellular telephones and other personal communication devices Some cellular telephones and similar devices transmit signals while they are ON even when not being used 2 Medium range mobile transceivers such as those used in police cars fire trucks ambulances and taxis These usually have the antenna mounted on the outside of the vehicle and Invacare CS Series Beds 14 Part No 1153410 2 SAFETY 3 Long range transmitters and transceivers such as commercial broadcast transmitters radio and TV broadcast antenna towers and amateur HAM radios Pinch Point A Disposal Other types of hand held devices such as cordless phones laptop computers AM FM radios TV sets CD players cassette players and small appliances such as electric shavers and hair dryers so far as we know are not likely to cause EMI problems to this product WARNING Pinch point between rail
45. the bed rails and assist devices or 68 Inch Rail may result in PATIENT ENTRAPMENT To reduce the risk of entrapment mount the bed rails assist devices or 68 Inch Rail as shown in the instructions When a PATIENT S condition such as disorientation due to medical or clinical conditions could lead to Patient Entrapment the mattress support platform should be left in the flat position while unattended except when required otherwise by medical staff for special or particular circumstances Use of incompatible trapeze units may cause injury and or damage Use only Invacare trapeze systems designed specially for the CS bed Standard Trapeze 1153385 or Heavy Duty Trapeze 1153386 Use of trapeze may be hazardous to residents or guests Possible entanglement may result from improper use of trapeze Evaluate residents prior to allowing them to use atrapeze Never allow children to use play or swing on the trapeze The Standard and Heavy Duty Trapeze are designed to provide support increased stability and assist the user when repositioning himself herself in bed The Standard and Heavy Duty Trapeze are NOT designed however to support the total body weight of an individual Use it for assistance ONLY Tipping hazard When in use always rotate the trapeze until the handle is located over the center of the bed and ensure that it drops down into the anti rotation position Improper mattress placement may result in PATIENT ENTRAPMENT To ensure FDA Ra
46. this manual must be performed by a qualified technician NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE Check all parts for shipping damage and test before using In case of damage DO NOT use Contact ICCI Customer Service Department 1 800 668 2337 Carrier for further instruction This Manual Electric bed has been engineered to provide reliable operation The bed has been thoroughly tested and inspected prior to shipment Invacare CS Series Beds 8 Part No 1153410 2 SAFETY 2 2 Operation Information General Warnings A WARNING When bed is not to be used for an extended period unplug electric bed from the wall outlet The electric bed is NOT designed to be used as a patient transport When transporting a patient use an approved patient transport Otherwise injury or damage may result If the unit is not working properly call a qualified technician to examine the unit and repair it Keep all moving parts including the main frame mattress deck head and foot sections and all drive shafts free of obstruction i e chair rails consoles window sills blankets sheets heating blankets pads tubing wiring etc and other types of products using electric cords which may get tangled around the bed side rails or legs during operation of the electric bed Never store anything under the bed The electric bed is equipped with locking casters When transferring into or out of the electric b
47. tion Tighten securely U kh WN Repeat STEPS 1 4 for the remaining board wing Invacare CS Series Beds 62 Part No 1153410 9 MAINTENANCE 9 Maintenance 9 1 Cleaning Instructions Pa ca A CAUTION Equipment or property DAMAGE or resident INJURY may occur during maintenance Unplug product before washing 2 Make sure all electrical parts motors control box and pendant are not damaged and that all connection ports are plugged DO NOT allow liquids to enter electrical components Disinfect and wash all components DO NOT submerge the bed frame or electrical parts 4 DO NOT power wash or steam clean Use household water pressure only Rinse thoroughly with water maximum temperature 10 F or 43 C DO NOT use solvents bleach alcohol petroleum products caustic agents or highly alkaline or acidic agents to clean the bed Retract each actuator to the minimum stroke length before washing to avoid degreasing the piston rod Dry all components before storing Part No 1153410 63 Invacare CS Series Beds 9 MAINTENANCE 9 2 9 3 9 4 9 5 Annual Maintenance Check A WARNING Failure to maintain your bed may reduce product life and increase unplanned maintenance When evaluating the condition of rail attachments it is necessary to consider all aspects of the bed rail system including consideration of the rails mattress and bed systems Refer to the Hospital Bed System Dimensional and Assessme
48. ugly between appropriate mattress keepers and properly sized head and foot ends that are designed for use on wide beds Use only a mattress of recommended specifications with this bed DO NOT use a mattress extension pad Refer to the Bed Specification section in this manual The following bed options are not compatible with the CS9FX600 68 inch rail Adjusting the CS9FX600 Bed Width All eight adjustable deck wings must be adjusted to the same width Ensure the appropriate bed and head board settings are used as described in this procedure The CS9FX600 has eight adjustable deck wings which can be adjusted to 36 in 39 in or 42 in The locations of the wings and adjustment knobs are shown in FIGURE 6 Invacare CS Series Beds 58 Part No 1153410 8 OPTIONS Underside of Bed Adjustable Head Section Adjustable Seat Adjustable Thigh Adjustable Foot Section Adjustment Section Section N Adjustment Knob Adjustment Knob Adjustment Knob Z a RE So le i MAN ve ET TUT PI TEL LLL Is CU A TY a YL DU KAI L Head End pug 3001 ig Adjustment Knob Adjustment Knob Adjustment Knob Knobs Adjustable Head Section Adjustable Seat Adjustable Thigh Adjustable Foot Section Section Section FIGURE 6 Adjustable deck wings knobs and snap buttons Part No 1153410 59 Invacare CS Series Beds 8 OPTIONS 36 in Width Side View 36 in Adjustment Adjustable Deck Wing Adjustment Knob Snap Button Top B
49. xed RF transmitters as deter mined by an electromagnetic site survey should be less than the compliance level in each frequency range Interference may occur in the vicinity of equipment marked with the following symbol NOTE At 80 MHz and 800 MHz the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people Field strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the CS Bed is used exceeds the applicable RF compliance level above the CS Bed should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as re orienting or relocating the CS Bed Over the freguency range 150 kHz to 80 MHz field strengths should be less than 3 V m Part No 1153410 19 Invacare CS Series Beds 3 EMC INFORMATION Recommended separation distances between portable and mobile RF communications equipment and the CS Bed The CS Bed is intended for use in an electromagnetic environment in which ra

Download Pdf Manuals

Related Search

Related Contents

Parts list for RL PRO DIAPHRAGM Model 914PR  Insignia NS-DPF8WW-09CA Digital Photo Frame User Manual  Especificación del caso de uso  Ethernet Device Configuration  Add-On Computer Peripherals (ACP) FTLX8541F2-AO network transceiver module  Nouvelles acquisitions - HES  Casio 2550 Watch User Manual  Beckett Water Gardening W1150 User's Manual  MP-IN001 - Rockwell Automation  

Copyright © All rights reserved. Failed to retrieve file