SM8985 - Marine Warehouse
Contents
1. Auto OFF appr 4 min How to use a bowthruster 1 Turn the main power switch for the bow thruster on Turn on the power to the receiver 2 Turn on the transmitter by pushing the transmitter s two ON buttons The remote system is now activated and then turns off automatically appr 4 min after the last usage see page 9 3 Please take some time to exercise thruster usage in open water to avoid damages to your boat 4 Turn the bow in the desired direction by pushing the red button for port movement or the green button for starboard movement How to use the windlass Please consult your windlass manual for use and precautions NB Max load on the windlass signal output is 3A Remote Control Deactivation Push the transmitter s OFF button the remote control deactivates automatically after appr 4 minutes after the last usage Turn off the power switch for the receiver e If in doubt try in open water first Installation amp User Manual Radio Remote 8985 8986 Page 10 ICS hemati IC SC Electr Receiver Active antenna 2m antenna extension Insulation lead connector lead amp 1 4 Grey Yellow Red Bow Thruster l Blue Windlass vy 4 Y vy AY Optional Auto main switch 12 24V supply Signal output 12 24V Signal output 12 24V NOT IN USE 12 24V supply Signal output 12 24V Signal output 12 24V Max load 3A 12 24V supply for rece2. 212 346 1329 seda denpar com UK Sleipner Motor Ltd South Brent Tel 44 1364 649 400 Fax 44 1364 649 399 andy sleipner co uk United Arab Emirates Teignbridge Propellers amp Marine Equipment Co Ltd Dubai Tel 971 4 324 0084 Fax 971 4 324 0153 teignpro emirates net ae USA Imtra Corporation New Bedford MA Tel 1 508 995 7000 Fax 1 508 998 5359 www imtra com side power imtra com Tel 47 69 30 00 60 Fax 47 69 30 00 70 sidepower sleipner no www side power com
3. Batt 5A fuse Fused power supply from a circuit with ON OFF switch Receiver Part 8932A grey black signal w lass down qm 5 red B _ windlass ctrl power Yellow Not in use Sleipner Motor AS www side power com CE Installation amp User Manual Radio Remote 8985 8986 Page 6 Programming additional receivers 18 SNIUYL MOQ OL luamod up ssejppum 9 pa joued joJuoo 18 SN14 Mog OL T aa EE esn UU ON iMOJJSA 5 S gt an o gt 3 8 E 3 A M l The original transmitter and receiver have the same factory preset code so that no programming is necessary When additional transmitters are to be used the receiver must be programmed again for all transmitters 1 Deactivate the receiver and all transmitters press OFF on all transmitters Turn off the main power switch for the thruster s 2 Turn on the power to the receiver 3 Remove the plastic plug from the receiver box as shown above 4 Press the PROG button at the receiver The receiver is then in Program mode The receiver will stay in Program mode for 30 seconds indicated by blinking LED 5 The receiver and transmitter are programmed by pressing both ON buttons on the transmitter for about 2 seconds During this 2 seconds the LED will change from blinking to continous light when the programming signal is received Turn off transmitter 6 Additional transmitters must be programmed according to ste
4. have the same factory preset code so no programmng is nec essary When additional transmitters are to be used the receiver must be programmed again for all transmitters please see programming section on page 7 If a Sidepower automatic main switch is fitted the OFF button on your transmitter will shut off the main switch providing no other control panels are ON Installation amp User Manual Radio Remote 8985 8986 Page 3 Receiver installation Prior to installation it is important that the responsible installer reads this guide to ensure necessary acquaintance with this product Warning e Remote receiver power supply negative lead must be connected to the thrusters s negative lead Caution Install the receiver minimum 1 meter 3ft and 3in from high power cables and NMEA cables or other sources of electrical interference i e navigation instruments radio communication devices electro motors and generators Install the receiver outside of shielded areas for radio signals i e Boxes made of steel or other material with shielding properties Install the receiver in a dry environment with cables pointing downwards The receiver as sembly is not waterproof When additional transmitters are to be used the receiver must be programmed again for all transmitters please see programming section on page 7 The receiver must have a separate power supply fitted with a 5 Amp fuse in the positive lead
5. olufsen dk Estonia Latvia Lithuania Miltec Systems OU Tallin Tel 372 5013997 Fax 372 6442211 www miltec ee tony miltec ee Finland Nautikulma OY Turku Tel 358 2 2503 444 Fax 358 2 2518 470 www nautikulma fi nautikulma nautikulma fi France Kent Marine Equipment Nantes Tel 33 240 921 584 Fax 33 240 921 316 www kent marine com contact kent marine com Germany Jabsco GmbH Norderstedt Tel 49 40 535 373 0 Fax 49 40 535 373 11 Greece Amaltheia Marine Athens Tel 30 210 2588 985 Fax 30 210 2588 986 www amaltheiamarine com amalmar otenet gr Iceland Maras EHF Reykjavik Tel 354 555 6444 Fax 354 565 7230 www maras is gummi maras is India Indo Marine Engineering Co Pvt Ltd Pune Maharashtra Tel 91 20 2712 3003 Fax 91 20 2712 2295 siddharth indogroup asia com Ireland Sleipner Motor Ltd South Brent Tel 44 1364 649 400 Fax 44 1364 649 399 andy sleipner co uk Israel Atlantis Marine Ltd Tel Aviv Tel 972 3 522 7978 Fax 972 3 523 5150 www atlantis marine com atlantis inter net il Italy Saim S P A Assago Milan Tel 39 02 488 531 Fax 39 02 488 2545 www saim group com Japan Turtle Marine Inc Nagasaki Tel 81 95 840 7977 Fax 81 95 840 7978 www turtle marine com info turtle marine com Malta S amp D Yachts Ltd Cali Tel 356 21 339 908 Fax 356 21 332 259 www sdyachts com info sdyachts com New Zealand Advance Tride
6. Confidence by Control fa D SIDE POW ER Thruster Systems Installation amp User Manual Radio Remote 8985 8986 EPE SLEIPNER MOTOR AS P O Box 519 N 1612 Fredrikstad Norwa i A Tel 47 69 30 00 60 www side power com Moro Fax 47 69 30 00 70 sidepower sleipner no 9 Made in Norway Contents Model anges EE Technical specifications Important precautions Receiver installation Visual wiring diagram Programming additional transmitters ss a sccesssecescerssesaccvecsscesscuseeceetteseseassecastexsacenvcevevssasacanceeveetseass Replacing the Dattenesis sis sciississscsess sececvssveesspesscessascavervesseveccns steven ces AR DELA A NETL SENAN PARERE Laera User precautions How to use Sidepower thrusters Serice Partners sinais saradas apra israel ese RERE ENEE Model range The radio remote control can control a single bow thruster or a bow and stern thruster combined The receiver can receive the signals of up to four transmitters Remote control kit 8985 consists of Receiver Part 8932A Transmitter incl battery Part 8986 Holding bracket for transmitter unit Part 8926 1x Wire harness 6 1282 Additional transmitters can be ordered separatly Part 8986 Part 8985 The transmitter and the receiver have the same factory preset code so no programmng is necessary The battery is already inserted in the transmitter e Additional tr
7. ansmitter s Part 8986 When additional transmitters are to be used the receiver must be programmed again for all transmitters please see programming section on page 7 We Sleipner Motor AS declare that this device complies with health and safety requirements according to the Directive 89 336 EEC of 23 May 1989 amended by 92 31 EEC and 93 68 EEC Installation amp User Manual Radio Remote 8985 8986 Page 2 Technical specifications Transmitter Receiver Model 8986 8932A Power feed 2 x 3V battery type CR2032 From thruster Frequency MHz 433 92 433 92 Adress range 65 000 65 000 Operation temp 150C 550C 150C 550C Technology S M T S M T HxWxD mm 95x48x25 90x60x30 Weight g 60 135 Important precautions You must always install at least one original Sidepower panel With the boat on land only run the thruster for a fraction of a second as without resistance it will accelerate very fast to a damaging rpm e This manual is intended to support educated experienced staff and is therefore not sufficient in all details for the correct installation e When installed in boats approved or classified according to international or special national rules the installer is responsible for following the demands in accordance with these regula tions classification rules The instructions in this guide can not be guaranteed to comply with all different regulations classification rules e The transmitter and the receiver
8. ed when planning your manouvering Never use a thruster close to somebody in the water as the thruster will draw objects close by into the tunnel and contact with the rotating propellers will cause serious injuries Never run a thruster for more that one second when the boat is not in the water as this can damage the electromotor seriously If the thruster stops giving thrust while the electromotor is running chances are that there is a problem in the drive system You must then immediately stop trying to run it and turn it off as running the electromotor for more than a few seconds without resistance from the propeller can cause serious damage to the electromotor When leaving the boat always turn off the main power switch for the thruster and turn off the power to the receiver We advice to always keep the main engine s running while using a thruster This will keep the batteries in a good charge condition This will also give better performance to the thruster as a higher voltage at the thruster results in a higher torque power in the electromotor Make sure that only one control is used at the same time if two panels are operated in oppo site directions at the same time the thruster will not run at all If they are operated in the same direction the thruster will run in this direction Installation amp User Manual Radio Remote 8985 8986 Page 9 Remote control ON Turn boat to Port Windlass Remote control OFF
9. iver Channel A Channel B Page 11 Installation amp User Manual Radio Remote 8985 8986 Argentina Trimer SA Buenos Aires Tel 54 11 4580 0444 Fax 54 11 4580 0440 www trimer com ar trimer trimer com ar Australia AMI Sales Freemantle WA Tel 61 89 331 0000 Fax 61 89 314 2929 ami amisales com au Austria G Ascherl GmbH Hard Bregenz Tel 43 5574 899000 Fax 43 5574 89900 10 www ascherl at office ascherl at Benelux ASA Boot Electro Watergang Tel 31 20 436 9100 Fax 31 20 436 9109 www asabootelectro nl info asabootelectro nl Brazil Electra Service Ltda Guaruja Tel 55 13 3354 3599 Fax 55 13 3354 3471 www electraservice br com albertoni electraservice com br Bulgaria Yachting BG Burgas tel 359 56 919090 fax 359 56 919091 www yachting bg info yachting bg Canada Imtra Corporation New Bedford MA Tel 1 508 995 7000 Fax 1 508 998 5359 www imtra com side power imtra com China Hong Kong Storm Force Marine Ltd Wanchai Hong Kong Tel 852 2866 0114 Fax 852 2866 9260 www stormforcemarine com sales stormforcemarine com Croatia Yacht Supplier Icici Tel 385 51 704 500 Fax 385 51 704 600 acy net hr Cyprus Ocean Marine Equipment Ltd Limassol Tel 357 253 69731 Fax 357 253 52976 oceanm spidernet com cy Denmark Gertsen amp Olufsen AS Horsholm Tel 45 4576 3600 Fax 45 4576 1772 www gertsen olufsen dk info gertsen
10. nt Ltd Auckland Tel 64 9 845 5347 Fax 64 9 415 5348 www advancetrident com service advancetrident com Norway Sleipner Motor AS Fredrikstad Tel 47 69 30 00 60 Fax 47 69 30 00 70 www side power com sidepower sleipner no Poland Taurus Sea Power SP Z 0 0 Gdansk Tel 48 58 344 30 50 Fax 48 58 341 67 62 Portugal Krautli Portugal Lda Lisboa Tel 351 21 953 56 00 Fax 351 21 953 56 01 www krautli com contact krautli pt Russia Standarte Starbeyevo Tel 7 495 575 67 23 Fax 7 495 575 39 77 www standarte ru info standarte ru NELAS E Sleipner Motor AS P O Box 519 N 1612 Fredrikstad Norway South Africa C Dynamics Cape Town Tel 27 21 555 3232 Fax 27 21 555 3230 www c dynamics co za info c dynamics co za Spain Imnasa Marine Products Girona Tel 34 902 300214 Fax 34 902 300215 www imnasa com imnasa imnasa com Sweden Sleipner AB Str mstad Tel 46 526 629 50 Fax 46 526 152 95 www sleipnerab se Switzerland Marine Parts Technics AG Volketswil Tel 41 1997 40 90 Fax 41 1 997 40 94 www marineparts ch info marineparts ch Singapore Malaysia Indonesia Vietnam Phillipines Island Marine Services Pte Ltd Singapore Tel 65 6795 2250 Fax 65 6795 2250 www island marine com karl island marine com Taiwan Mercury Marine Supply Kaohsiung Tel 886 7 3317 293 Fax 886 7 3314 232 Turkey Denpar Ltd Istanbul Tel 90 212 346 1332 Fax 90
11. p 5 within the same 30 seconds time period when the receiver is in Program mode 7 Wait until the LED stops to blink The total Program mode time is about 30 seconds The programming is now finished 8 Turn on the transmitter s and check that the receiver LED is blinking slowly User mode 9 Turn off the power to the receiver and put the plastic plug back in place Installation amp User Manual Radio Remote 8985 8986 Page 7 Replacing the batteries Batteries WARNING Before working on the transmitter deactivate the transmitter and the receiver push OFF on the transmitter s and turn off the power to the receiver as well as the thruster mainswitch 1 Open the transmitter 2 Take out the batteries 3 Insert the new batteries Type CR2032 3V Brand name recommended Be sure to insert the battery with the positive pole up 4 Close the transmitter Put the cover back in place ensure that the rubber seal between remote upper and lower part is located correctly Place the 3 screws remember sealing washer in their recessed holes and tighten Installation amp User Manual Radio Remote 8985 8986 Page 8 Important user precautions Ensure that you know the location of the main battery switch that disonnects the thruster from all power sources batteries so that the thruster can be turned off in case of a malfunction If a Sidepower automatic main switch is fitted the OFF button on your
12. that has either a separate power switch or is shut of by the thrusters system main power switch The receiver can not be powered by the thrusters s control looms even if you find posi tive and negative lead there e Mount the receiver using the two screw holes please see picture on page 6 Optimised installation Fig 1 3 The receiver antenna must be placed in a vertical position minimum 1 meter 3ft 3in above sea level The receiver has an extended antenna of 2 meters 6ft Gin If there is a problem with signal transferring try to move the extended antenna to a more optimised position Above sea level Away from sources of electrical interference Note Faulty installation will render all warranty given by Sleipner Motor AS void Installation amp User Manual Radio Remote 8985 8986 Page 4 A min 100cm E d ES A O O Installation 8 User Manual Radio Remote 8985 8986 Page 5 Receiver installation Receiver Part 8932A J9 SMAY MOQ OL Mount the receiver by using the 2 screwholes Sen UU JON MOJJSA SSEJpuIM a Q S 2 S 5 S gt v 5 D 8 E g 8 8 3 A AN Visual wiring diagram To bow thruster To bow thruster control panel Yellow Sidepower automatic main switch optional Black 12 24V Batt Ce Red 12 24V
13. transmitter will shut off the main switch providing no other control panels are ON How to activate the system Turn on the main power source for the thruster system Turn on the power to the receiver The thruster system is then activated by pushing the two ON buttons on the transmitter see page 9 To turn of the radio remote control push the OFF button on the transmitter Auto Off after appr 4 minutes for safety reasons When using a single transmitter The system turns off automatically appr 4 minutes after the last usage When using more than one transmitter or additional radio link control panels The system turns off automatically appr 4 minutes after the last usage of the control unit that initially activated the system even if other control units have been operated in the meantime The system is off even if these other control units still show the blinking LED on the transmitter To use these transmitters the system must be activated again by pushing the two ON but tons Remember to turn off the radio remote control by pushing the OFF button on the transmitter and to turn off the power switch for the receiver when you have finished your maneuvering The maximum continues usage time of the electrical thruster is approx 3 minutes The electro motor has a built in thermal cut off switch that will shut it off when overheating and re engage it when it has cooled down some This should be consider
Download Pdf Manuals
Related Search