Home

APR-3100N Series

1. 5 5 1 2 Block WAN Requests Block Anonymous WAN Stops the router from responding to pings from the WAN Requests Ping Prevents multicast packets from reaching the LAN Filter WAN NAT Prevents hosts on the LAN from using the WAN address of Redirection router to contact servers on the LAN Filter IDENT Prevents WAN access to port 113 The settings must be applied and saved before they take effect 38 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 5 1 3 Log Management Log Management Log Log Enable Disable Log Level low Y Options Dropped Disable Y Rejected Disable Y Accepted Disable Y Keeps activity logs when Enabled Log Level Higher log level will log more actions Incoming Log Most recent incoming traffic Outgoing Log Most recent outgoing traffic The settings must be applied and saved before they take effect 39 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 5 2 VPN Passthrough Virtual Private Networking VPN is typically used for work related networking For a VPN tunnel the router supports IPSec Passthrough PPTP Passthough and L2TP Passthough Setup Wireless Services Security NAT QoS Firewall VPN Passthrough Virtual Private Network VPN VPN Passthrough IPSec Passthrough Enable PPTP Passthrough Enable L2TP Passthrough Enable ES VPN Passthrough Description Administration Status Int
2. ST 14 32 1 BASICS SUID been cn de 14 De DIN a ee 17 5 2 3 MAC Address Clone 19 5 2 4 Advance Routing 20 dB NON 21 Sa 0 EQIP TUNNEL sa 23 EE ee 24 D a BR SIC SONO ee un 24 ele 29 550 9 Wireless SOC ner 30 SS MAGIE ee ee ee eee 31 SVD m 32 BA S TVICOS E 33 oa ONICO 33 SA2 VPN E 35 543 USB 37 9 44 HOLSDOL POM All iiic beoe Rite eite 37 I 6 cos teancinencetetotantecaatenns tesdessainmncineestanstanans 38 Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 949 1 FOWA oee ce 38 29 2 VPN HE tel el ME 40 5 6 Access Restrictions 41 DO NNN 41 Sie OO G 43 5 7 1 Port Forwarding ccccccceecceeeeeeeeeeeeseees 43 5 7 2 Port Range Forwarding 44 5 7 3 Port Triggering seseeeeseeeseee 45 SINE Eq e 46 SET IB PA 47 SP Oo EE EE 47 5 0 AOMIAISTENON auos cnius oar eS EP OERE 50 5 8 1 Management 50 9o 2 EL GN ERT 52 58 I GO MANS ee 53 s NO ER 53 5 8 5 Factory Defaults 54 5 8 6 Firmware Upgrade 54 Sf oM AH rz Led UO a S 55 Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 Ee 56 Sol ai 56 e EE a aa 57 STE d A 58 5 9 4 Bandwidth eic idi mv ca ctu med ea Du ten a 59 5 999 Salil O eres RUD 60 O COMS a n
3. 1 RJ45 to DB9 serial console cable 1 5 Safety Precaution Attention If the DC voltage is supplied by an external circuit please use a protection device on the power supply input The industrial APR 3100N series hardware specs ports cabling information and wiring installation will be described within this user manual Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 2 Hardware Description 2 1 Physical Dimensions Figure 2 1 below shows the physical dimensions of Antaira s APR 3100N series industrial 802 11a b g n access point VPN router W x D x H is 46mm x 115mm x 155mm 00000 9 Figure 2 1 APR 3100N Series Physical Dimensions Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 2 2 Front Panel The front panel of the APR 3100N series industrial 802 11a b g n access point VPN router is shown below in Figure 2 2 tte Power Status LEDs WLAN Signal Strength LED Diaanostic LED Ethernet 2 Ethernet 1 Reset Button Figure2 2 The Front Panel of APR 3100N Series 2 3 Top View Figure 2 3 below shows the top panel of the APR 3100N series that is equipped with one 6 pin removal terminal block connector for dual DC power inputs 12 48VDC Relay Output 1A 24VDC Ground Figure2 3 Top Panel View of APR 3100N Series Vi VI Relay V2 V2 LPWR U L J LPWR 2J Power 1 Power 2 12 48VDC 12 48VDC Industrial Wireless Ethernet R
4. 5 4 Services oa deine CONIROL PANEL Setup Wireless Services Security Access Restrictions NAT QoS Administration Status Hotspot 5 4 1 Services DHCP Server The DHCP server will assign IP addresses to your local devices The DHCP configuration is on the main setup page although some functions are available through the services tab DHCP Server Use JFF52 for client lease DB Use NVRAM for client lease DB Used Domain WAN LAM Domain Additional DHCPd Options Used Domain Users select which domain the DHCP clients should get as their local domain The WAN domain will be set on the Setup screen or the LAN domain can be set here LAN Domain The user can define the local LAN domain which will be used as the local domain for the DNSmasq and DHCP service if chosen above 33 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 DNSmasq The DNSmasq is a local DNS server The DNSmasq will resolve all host names known to the router from the DHCP as well as forwarding and caching DNS entries from remote DNS servers DNSMasq DNSMasq Enable Disable Local DNS Enable Disable No DNS Rebind Enable Disable Additional DNSMasq Options Local DNS Enable will allow DHCP clients on the LAN to resolve static and dynamic DHCP hostnames No DNS Rebind DNS rebinding is a malicious attack that causes web page visitors to run a client script that can attack other machines on the net
5. HTB is useful for limiting the clients download upload rates as well as Packet Scheduler preventing one user s monopolization of bandwidth HFSC Hierarchical Fair Service Curve allows the attached quest to build an interface tree thus each queue can have further child queues Each queue can have a priority and a bandwidth assigned The priority controls the time packets take to get sent out while the bandwidth will affect the throughput To use the QoS the user must enter bandwidth values for the uplink and downlink Typical values are between 8096 9596 of Uplink Downlink maximum bandwidth Note If QoS is only to be applied to the uplink bandwidth enter 0 for the downlink DO NOT enter O for the uplink TCP Packet Priority Prioritize small TCP packets with the following flags ACK SYN FIN RST Services Priority i00b5aso Standard F Add 100ba O0 Ly Add Edit Service QoS Priority Cont Description Prioritization of TCP packets with ACK SYN FIN RST For the most part the user will benefit from having SYN FIN and RST 2 checked ACK will be dependent on how the network is setup TCP Packet Priority E and how much P2P activity there will be Personal testing on the network should be performed If very little P2P activity is present it would be beneficial to enable ACT as well The user can press the Add button and choose from a 48 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 dr
6. IP settings will use different address space the device will become unreachable Assign the subnet mask of the IP address If the DHCP client function is MN orc Gateway Assign the network gateway for the switch If the DHCP client function is enabled user is not required to assign the Gateway This is the IP address of the host router which resides on the external network and provides the point of connection to the next hop towards the internet This can be a DSL modem Cable modem or a WISP gateway router The device will direct all the packets to the gateway if the destination host is not within the local network The Gateway IP address should be from the same address space on the same network segment as the device s external network interface Wireless interface in the Station case and the LAN interface in the AP case This is used to define the device s IP classification for the chosen IP address range This sequence 255 255 255 0 is a typical netmask value for Class C networks which supports the IP address range 192 0 0 x to 223 255 255 x Class C network Netmask uses 24 bits to identify the 61 Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 network alternative notation 24 and 8 bits to identity the host The Domain Name System DNS is an internet phone book which translates domain names to IP addresses These fields identify the server IP addresses where the DNS requests are forwarded by th
7. RJ 45 LED on the industrial Ethernet router will turn on when the cable is connected to the networking device e Please refer to the LED Indicators section for LED light indication When all connections are set and the LED lights all show normal the units connection is complete 11 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 Web Management 5 1 Web Console Configuration This section introduces the configuration by web browser 5 1 1 About Web Based Management All of Antaira s industrial managed routers are embedded with HTML web console interfaces that have a flash memory on the CPU board It is a user friendly design with advanced management features that allow users to manage the router from anywhere on the network through any Internet browser such as Internet Explorer version 9 0 or above is recommended Firefox Chrome and many more Preparing for Web Console Configuration Antaira s industrial router comes with a factory default value outlined below M Default IP Address 192 168 1 1 B Default User Name root M Default Password admin System Login 1 Launch any Internet browser 2 Type in factory default IP address http 192 168 1 1 of the router Press Enter 3 Thelogin screen appears Authentication Required The server http 192 163 1 1 J requires a username and password The server says Antaira User Name root Password numi Log In Cancel Figu
8. 65536 kB 54 Free 39372 kB 61720 kB 64 Used 22348 kB 61720 kB Buffers 2488 kB 22348 kB Cached 6336 kB 22348 kB mg Active 4348 kB 22348 kB ERES Inactive 5636 kB 22348 kB mm Space Usage NVRAM 18 97 KB 64 KB Network IP Filter Maximum Ports 4096 Active IP Connections 114 56 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 Basic system information about the router such as the firmware System and kernel versions as well as the MAC address CPU How loaded the CPU is at any given time Also listed is the CPU model and clock speed The percentages of the memory and how the router is allocating Memory memory usage Is the amount of non volatile memory is available on the router NVRAM Non volatile RAM is memory that will keep the information even if the power is turned off IP Filter Maximum Ports default setting is 4096 it is not recommended to increase this number 5 9 2 LAN This status screen shows all of the current LAN status and configuration settings Please note that within the Status tab all information is read only Changes are made under the standard tabs not the Status overview tabs Local Metwork LAM 5tatus MAC Address ZC CB 0D 08 1D 96 IP Address 192 168 1 177 Subnet Mask 255 255 255 0 Gateway 0 0 0 0 Local DNS 0 0 0 0 Active Clients 192 168 1 179 fOibf 97 da 79 6e 100 Dynamic Host Configuration Protocol DHCP Status DHCP Server Di
9. DDNS service provider The dropdown EE Custom selection has several possible DDNS service providers If the end user does not wish to use a DDNS server simply leave the dropdown on the default Disable setting 5 2 2 2 Setting up a DDNS Service ANTAII CONTROL PANEL Setup Wireless Services Security Access Restrictions NAT QoS Administration Basic Setup DDNS MAC Address Clone Advanced Routing Networking EoIP Tunnel Dynamic Domain Name System DDNS DDNS DDNS Service DynDNS org Username Password Hostname Type Dynamic Wildcard Do not use external ip check Options Force Update Interval 0 Default 10 Days Range 1 60 DDNS Status DDNS function is disabled Userame Setup a Username ough fe DONS sance provder Hostname Serup a Hostname tough he DONS serres provider Dynamic Allows a hostname that was chosen by the user through the DDNS service provider to point to the users IP address Static Like Dynamic service but the DNS host will not expire after 35 days without updates Custom Creates a managed primary DNS that provides the 18 Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 user more control over the DNS Wildcard Enabling the Wildcard feature allows the users host to be ildcar aliased to the same IP address and the DNS server Allows the DDNS function to pick up the WAN IP from the router External IP Check l l l instead of checking o
10. NCAIrA APR 3100N Series Industrial AP VPN Router IEEE 802 11a b g n User Manual Version 1 0 Ntaira www antaira com Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 Copyright 2014 Antaira Technologies LLC All Rights Reserved This document contains information which is protected by copyright Reproduction adaptation or translation without prior permission is prohibited except as allowed under the copyright laws Trademark Information Antaira is a registered trademark of Antaira Technologies LLC Microsoft Windows and the Windows logo are the trademarks of Microsoft Corp NetWare is the registered trademark of Novell Inc WMM and WPA are the registered trademarks of Wi Fi Alliance All other brand and product names are trademarks or registered trademarks of their respective owners Notice Copyrights 2014 by Antaira Technologies LLC All rights reserved Reproduction adaptation or translation without prior permission of Antaira Technologies LLC is prohibited except as allowed under the copyright laws Disclaimer Antaira Technologies LLC provides this manual without warranty of any kind expressed or implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose Antaira Technologies LLC may make improvements and or changes to the product and or specifications of the product described in this manual without prior noti
11. Range Forwarding Forwards un None rr Port Range Forwarding allows the user to set up public services on the network such as web servers ftp servers and e mail servers Specialized Internet applications are any applications that use Internet access to perform functions such as video conferencing or online gaming To add a new port forwarding rule click add and fill in the fields listed below This allows the user to set a range of ports If the user would like to only forward a single port please refer back to the Port Forwarding section Port Range Forwarding Forwards 0 Both Y 0 0 0 0 Port Range Forwarding Description Application Enter the name of the application The number of the first port in the range that is to be seen by users on the Internet and forwarding to a PC on the local The number of the last port of the range that will be seen by pe users on the Internet and forwarding to a PC on the local network Choose the correct protocol based upon the application the Protocol choices are TCP UDP or Both IP Address The IP address of the PC running the application The number of the internal port port number used by the Port To mM application Enable Check to enable port forwarding for the application The settings must be applied and saved before they take effect 44 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 7 3 Port Triggering Setup
12. V1 0 5 9 4 Bandwidth The unit will have bandwidth monitoring tools available for both the LAN and the Wireless of the router Below are examples of the bandwidth graphs that the user might see Bandwidth Monitoring LAN eth1 Bandwidth Monitoring LAN In 58 Kbps Switch to bytes s In 49 Kbps Switch T bytes s Out 33 Kbps Autoscale follow Out 28 Kbps gd follow Im Ir 3 Mbps A A E I JA Sa A A J J j UN N AA kal L VN VV NI w A kd T 1 A nm hn Ze Bandwidth Monitoring Wireless athO0 In 0 Kbps Switch to bytes s Out 24 Kbps Autoscale follow d 59 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 9 5 Sys Info Setup Administration Status Router WAN mue im rvices CONTROL PANEL 5 Restrictions Administration System Information Router Services Router Marne Antaira DHCP Server Disabled Router Model Industrial Router WRT radauth Disabled LAN MAC 7C CB 0D 08 10D 96 USB Support Enabled WAN MAC FC CB 00 06 10 98 Wireless MAC 7C CB 0D 08 1D 98 id WAN IP 0 0 0 0 Total Available 60 3 MB 64 0 MB LAN IP 192 168 1 1 MEE LENE ME Used 38 4 MB 60 3 MB Wireless Buffers 2 4 MB 38 4 MB Radio Radio is On Cached 6 4 MB 38 4 MB Mode AP Active 5 0 MB 38 4 MB Network Mixed Inacti
13. WINS server is being used enter the servers IP information here Leave blank if no WINS server is present 5 2 1 5 Time Settings Time 5ettings NTP Client Enable Disable Time Zone UTC 01 00 P Summer Time DST last Sun Mar last Sun Oct Y Server IF Name Network Time Protocol Used for time synchronization NTP Client between the client and the network time server UTC is the Coordinated Universal Time based off the mean Time Zone solar time at Earths prime meridian Select the time zone the unit is located at Summer Time DST Offset of time based from the UTC time Server IP Name Enter either the servers IP address or assigned name 5 2 2 DDNS crx air a nee Setup Wireless Services Security Access Restrictions NAT QoS Administration Status Basic Setup DDNS MAC Address Clone Advanced Routing Networking EoIP Tunnel Dynamic Domain Name System DDNS DDNS DDNS Service Disable v Apply Settings Cancel Changes 17 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 2 2 1 DDNS Service The router offers a Dynamic Domain Name System DDNS The DDNS allows users to assign a fixed host and domain name to a dynamic DynDNS org internet IP address This is useful when hosting a website or FTP server eedansafraid org ZoneEdit com No IP com l 3322 0rg Note Before using this feature the end user will need to sign up for easyDNS com the DDNS service with a
14. Wireless Services Security Access Restrictions NAT Qo5 Administration Status Port Forwarding Port Range Forwarding Port Triggering UPnP DMZ Qos Port Triggering allows the user to perform port forwarding without setting a fixed PC By setting a port triggering rule the user can allow inbound traffic to arrive at a specific LAN host using different ports than those used for the outbound traffic The outbound traffic triggers to the inbound ports that the traffic is directed To add a new port triggering rule click on the Add button and fill in the fields listed and described below Port Triggering Forwards Port Triggering Description Application Enter the name of the application The number of the first and the last port of the range that should be triggered If a PC sends outbound traffic from those ports Triggered Range incoming traffic on the Forwarded Range will be forwarded to that PC Enter the first and last port of the range which should be Forwarded Range forwarded from the Internet to the PC which has the Triggered Range Enable Check to enable port forwarding for the application The settings must be applied and saved before they take effect 45 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 7 4 UPnP Setup Wireless Services Security Access Restrictions NAT Qo5 Administration Status Port Forwarding Port Range Forwarding Port Trigger
15. of each packet and address it to the group of computers that want to receive it This technique addresses packets to a group of receivers rather than to a single receiver It depends on the network to forward the packets to the hosts which need to receive them Common Routers isolate all the broadcast thus multicast traffic between the internal and external networks however provides the multicast traffic pass through functionality Value Description Determines the packet size of a transmission and through the use of an access point helps control traffic flow RTS CTS Request to Send Clear to Send is the mechanism used by the 802 11 wireless networking protocol to reduce frame collisions introduced by the hidden terminal problem RTS CTS packet size threshold is 0 2347 bytes If the packet RTS Threshold size the node wants to transmit is larger than the threshold the RTS CTS handshake gets triggered If the packet size is equal to or less than threshold the data frame gets sent immediately System uses Request to Send Clear to Send frames for the handshake which provide collision reduction for access point with hidden stations The stations are sending a RTS frame first while data is send only after handshake with an AP is 63 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 completed Stations respond with the CTS frame to the RTS which provides clear media for the requesting station to send the data CTS
16. remote location The default port is 8080 Introduces a short delay while booting 5 seconds This delay allows for the user to initiate the download of new firmware if the Boot Wait l l l current firmware will not boot or re flashing through the web interface does not work The cron subsystem schedules execution for Linux commands The command line or startup scripts will be required to use this A limited 802 1x server to perform proper hand shake with mn Windows XP clients using WPA security Short press Reset the router reboot Reset Button Long Press gt 10 seconds will reset the unit to factory default settings Routing Routing Enable Disable Language Selection Language English Y IF Filter Settings adjust these for F2F TCP Congestion Control vegas T Maximum Ports 4096 Default 32768 Fange 256 65535 TCP Timeout in seconds 3600 Default 3600 Range 1 86400 UDP Timeout in seconds 120 Default 120 Range 1 86400 Overclocking Mot Supported Router GUI Style stie red v 51 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 Routing enables the OSPF and RIP routing daemons if those features have been set within the Advance Routing page Language Selection Allows the user to switch the language within the router If peer to peer applications are running on the network it would be beneficial to increase the maximum ports and well as lower the TCP UDP timeouts to impro
17. to a specified mounting point 5 4 4 Hotspot Portal The user can set the router as a Hotspot gateway with authentication and accounting Most hotspot software requires a server to store the user settings and login information Hotspot Portal Hotspot System HOTSPOTSYSTEM Hotspot System Enable Disable Wifidog mh LE Weg Wifidog Gateway Enable Disable Chillispot Chillispot Enable Disable 3 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 5 Security tz meme 1S Setup Wireless Services Security Access Restrictions NAT Qos Administration Status Firewall VPN Passthrough 5 5 1 Firewall The Firewall can be either enabled or disabled The user can also set additional filters block certain WAN interface requests and manage logs Additional Filters Filter Proxy Filter Cookies Filter Java Applets Filter ActiveX Block WAN Requests Block Anonymous WAN Requests ping Filter Multicast Filter WAN NAT Redirection Filter IDENT Port 113 5 5 1 1 Additional Filters Additional Filters Description Filter Proxy Blocks HTTP requests containing the host string HTTP requests that contain Cookie string are identified and an Filter Cookies attempt is made to stop their usage Filter Java Applets Blocks HTTP requests containing URL ending in js or class Filter ActiveX Blocks HTTP requests containing URL ending in ocx or cab
18. user can save specific command lines to be executed at Startup Shutdown either the routers startup or shutdown The user can input firewall commands into the text area Note Only one command per row 5 8 4 WOL This page allows the user to wake up hosts that are located on the local network Setup Wireless Services Security Access Restrictions NAT Qos Administration Status Management Keep Alrve Commands WOL Factory Defaults Firmware Upgrade Backup Wake On LAN Available Hosts ARE A LL TR TEEN To A eae Er NTN 3 MAC Address DAS OMe TR IP Address Enable WoL WOL Addresses Manual WOL MAC Address es zx IP Address UDP Port Manual Wake Up Automatic Wake On LAN Wake On LAN daemon WOL daemon Enable Disable 53 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 Show the user a list of hosts to add remove from the WOL Available Hosts address list Units with static IP addresses as well as units that are automatically discovered though DHCP clients WOL Addresses Allows the user to wake individual hosts in the WOL list Manual WOL Allows the user to wake an individual or list of hosts 5 8 5 Factory Defaults Wireless Services Security Access Restrictions NAT QoS Administration Status Management Keep Alive Commands Factory Defaults Firmware Upgrade Backup Factory Defaults Reset router settings Restore Factory Defaults Yes No If at some point the
19. workstation etc must be less than 100 meters 328 ft long 2 7 Wiring the Power Inputs Please follow the steps below to insert the power wire 1 Insert the positive and negative wires into the PWR1 V1 V1 and PWR2 V2 V2 contacts on the terminal block connector as shown below in Figure 2 7 Figure 2 7 Power Terminal Block V1 V1 V2 V2 2 Tighten the wire clamp screws to prevent the wires from loosening as shown below in Figure 2 8 Figure 2 8 Power Terminal Block Note e Only use copper conductors 60 75 C tighten to 5lbs The wire gauge for the terminal block should range between 18 20 AWG Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 2 8 Wiring the Fault Alarm Contact The fault alarm contact is in the middle of the terminal block connector as the picture shows below An application example for the fault alarm contact is shown below in Figure 2 9 VEN PWR1 Sg PWR2 TAJEA aM ke 24V de 1A Resistance Insert the wires into the fault alarm contact No 3 amp 4 Figure 2 9 Wiring the Fault Alarm Contact Note e The wire gauge for the terminal block should range between 12 24AWG Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 3 Mounting Installation Rear Panel ofthe switch 3 1 DIN Rail Mounting The DIN Rail is pre installed on the industrial router from the factory If the DIN Rail is not on th
20. 40MHz frequency and can be set to above or below the main channel This extension channel needs to be continuous from the main channel If the main channel is set to channel one the unit cannot have an extension channel below due to there not being any other channels below channel one 5 3 1 6 Wireless Network Name SSID The SSID is the Service Set Identifier used to identify the operators wireless LAN The SSID is set by the user in Access Point or Access Point WDS mode All of the client devices within the range of the access point will receive the broadcasted SSID advertising the SSID Wireless SSID Broadcast Once disabled the SSID of the access point will no longer be broadcast This means that client devices will not see the SSID of the unit even though they might within range A A user wishing to connect with a client device to a hidden SSID will need to directly input the SSID and password information The hidden SSID acts as an additional layer of security making it harder for unwanted users to connect to the network 27 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 3 1 7 Advanced Settings By selecting the Advanced Settings box the following options will become available to the user Advanced Settings Dy Regulatory Domain UMITED STATES Y TX Power 20 dBm Antenna Gain 0 dBi Protection Mode None Y RTS Threshold Enable Disable Short Preamble Enable Disable Outdoor Band En
21. AT QoS Administration Setup Wire Basic Setup DDNS MAC Address Clone Advanced Routing Networking EoIP Tunnel Advanced Routing Operating Mode Operating Mode Gateway Y Router Static Routing Select set number 1 Route Name Metric 0 Destination LAN NET 0 0 D 0 Subnet Mask OI OI OI 0 Gateway 0 0 OI 0 Interface LAN amp WLAN Y Advanced Routing Gateway Gateway If the router is hosting the Internet connection the Operating Mode router will perform NAT in Gateway mode 5 2 4 2 Router Setup Wireless Services Security Access Restrictions NAT QoS Administratioi Basic Setup DONS MAC Address Clone Advanced Routing Networking EoIP Tunnel Advanced Routing Operating Mode Operating Mode Router Y Dynamic Routing Interface Advanced Routing Description Router Tells the end user if the destination IP address is on the LAN amp WAN WAN or Loopback Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 2 5 Networking ANAIA TE Setup Wireless Services Security Access Restrictions NAT QoS Administration Status Basic Setup DDNS MAC Address Clone Advanced Routing Networking EoIP Tunnel 5 2 5 1 VLAN Tagging VLAN Tagging RSR Tagging Taggin ggmg VLANO Interface ath Tag Number 0 Priolo Y Ad E Tagging allows the user to create a new VLAN interface from the standard interface by filtering using defined TAG numbers 5 2 5 2 Bridging Bridgi
22. All ports on this industrial Ethernet switch support the automatic MDI MDI X operation Users can use straight through cables see the figure below for all network connections to PCs servers other switches and hubs With straight through cable pins 1 2 3 and 6 at one end of the cable are connected straight through to pins 1 2 3 and 6 at the other end of the cable The table below Table 2 3 shows the 10BASE T and 100BASE Tx MDI and MDI X port pin outs Pin MDI X Signal Name MDI Signal Name 1 Receive Data plus RD Transmit Data plus TD Receive Data minus RD Transmit Data minus TD Transmit Data plus TD Receive Data plus RD 08 Transmit Data minus TD Receive Data minus RD Table 2 3 Ethernet Signal Pin Outs Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 The following figures show the cabling schematics for straight through and crossover Switch Router or PC Switch Switch 3 TD 3 TD 3 TD 5 RD 6 TD 6 RD 6 TD 6 TD Ll BD hai TD RD 1 RD 2 RD 4 2 TD 2 RD 2 RD Figure 2 5 Figure 2 4 Straight Through Cable Schematic Crossover Cable Schematic 2 6 Cabling E Twisted pair segments can be connected with an unshielded twisted pair UTP or shielded twisted pair STP cable The cable must comply with the IEEE 802 3u 100BaseTx standard e g Category 5 5e or 6 The cable between the equipment and the link partner switch hub
23. Disable and if enabled wireless clients are isolated AP Isolation and access to and from other wireless clients is stopped Looks for Airport or Military pulses from radars to prevent Radar Detection unintended interference between equipment ScanList Default is 2000 meters The sensitivity range is a timing adjustment based on the distance between linking devices When the time needed to transmit is greater than the amount of Sensitivity Range time sender waits before resending the same packet Typically the ACK time should be 2 times the distance between devices measured in meters If the ACK time is to low information can be lost or not connect Max Associated Clients The number of clients can be connected to the access point Activates a compatibility with Mikrotik RouterOS when MTik Compatibility performing tests Wireless interface must be bridged with the LAN ports Client Network Configuration on wireless and on LAN port Unbridged allows a separation between the WLAN and LAN 5 3 2 SuperChannel Allows for the use of unique frequencies in the IEEE 802 119 range 2192 Mhz 2732 Mhz and IEEE 802 11a 4915 mhz 6100 Mhz Note This feature has not been enabled yet 29 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 3 3 Wireless Security ANTAA lt onror rane Setup Wireless Services Security NAT Q05 Administration Status Basic Settings SuperCha
24. Password password The length cannot exceed 32 characters Re enter to Confirm Re enter the new password for verification Web Access Protocol HTTP HTTPS Auto Refresh in seconds 3 Enable Info Site Enable Disable Info Site Password Protection Enabled Info Site MAC Masking Enable Disable Management Continued Description The user can select to use either HTTP or HTTPS protocols Protocol Please note that any changes will require a manual reboot of the router Refers to the information in the Status Tab then the Sys Info Enable Info Site tab By disabling this access to this page will not be accessible outside the network Info Site Password When the Info Site is enabled the password protection can be Protection setup Hiding of the first 4 hex groups of the MAC address of the DHCP Info Site MAC Masking and wireless clients that external users can see through the Sys Info page Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 Remote Access Web GUI Management Enable Disable SSH Management Enable Disable Telnet Management Enable Disable Allow Any Remote IP Enable Disable Boot Wait Boot Wait Enable Disable Cron Cron Enable Disable Additional Cron Jobs BO2 1x 802 1 Enable Disable Reset Button Reset Button ZS Enable Disable Default is disabled by enabling this the user is able to managed Remote Access the router from a
25. able Disable TX Antenna Chains 142 T RX Antenna Chains 1 2 T AP Isolation Enable Disable Radar Detection Enable Disable ScanList default Sensitivity Range ACK Timing 2000 Default 2000 meters Max Associated Clients 256 Default 256 Clients MTik Compatibility Enable Disable Network Configuration Unbridged Bridged 20 dBm is the default value and provides the radio 100mW of Tx power power Higher values are not recommended due to excessive heat being generated by the radio causing a lower lifespan CTS protection allows multiple client devices to send data a Mode simultaneously to a single access point The CTS clear to send protection is able to set an order of what device gets to transmit preventing the access point from discarding all info This should stay at the default 2346 value This specifies the RTS Threshold maximum size for a packet before data is fragmented into multiple packets Default is Long Preamble a short preamble can be used but Short Preamble communication issues might occur when communicating with IEEE 802 11b devices Outdoor Band By enabling the outdoor band the user is able to reach the Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 BEEN higher frequency channels Used based on external antennas to provide optimum Tx Antenna Chains performance Used based on external antennas to provide optimum Rx Antenna Chains performance Default is
26. able or disable the use of DMZ DMZ Host IP Address The IP address of the PC using the DMZ service 5 7 6 QoS Setup Wireless Services Security Access Restrictions NAT QoS Administration Status Port Forwarding Port Range Forwarding Port Triggering UPnP DMZ Qos The Quality of Service QoS helps bandwidth management prioritization on the router Interactive traffic Internet telephone telnet will get priority and bulk traffic file transfers or P2P will receive lower prioritization QoS allows bandwidth control allocation to different services net masks and MAC addresses QoS is divided into five different bandwidth tiers Maximum Premium Express Standard and Bulk Unclassified services will use the Standard bandwidth class 5 7 6 1 QoS Quality Of Service QoS Qos Settings Start Qos Enable Disable Port WAN T Packet Scheduler HB Uplink kbps o Downlink kbps 0 TCP Packet Priority Prioritize small TCP packets with the following flags ACK SYN FIN RST 47 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 RS ss eee When enabled the user will need to choose to enable the QoS CE HTB Hierarchical Token Bucket is less resource demanding than HFSC HTB helps in controlling the use of outbound bandwidth on a given link HTB allows you to use one physical link to simulate several slower links as well as sending different kinds of traffic on the different simulated links
27. aemon OpenVPN Server Daemon OpenVPN Disable OpenVPN Client OpenVPN Client Start OpenVPN Client Save Apply Settings Cancel Changes PPTP Server Configuring the PPTP server allows the user to access the LAN remotely at home PPTP Server PPTP Server PPTP Server Enable Disable Broadcast support Enable Disable MPPE Encryption Enable Disable DNS1 DNS2 WINS1 WINS2 MTU 1436 Default 1436 MRU 1436 Default 1436 Server IP Client IP s Max Associated Clients 64 Default 64 Authentication Radius Local User Management CHAP Secrets Server IP The IP address of the router Client IP A list or range of IP address for remotely connected devices Note Do not overlap with the range of DHCP addresses CHAP Secrets A list of usernames and passwords for the VPN login Note line Ex joe joepassword MTU Maximum Transmission Unit MRU Maximum Receive Unit one user per Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 PPTP Client PPTP Client PPTP Client Options Enable Disable Server IP or DNS Name Remote Subnet DI DI Dj Remote Subnet Mask DV DV DV 0 MPPE Encryption mppe required MTU 1436 Default 1436 MRU 1436 Default 1436 NAT Enable Disable Username DOM AIN Username Password Unmask Additional PPTP Options Server IP or DNS Name The IP address or DNS Name of the VPN server to connect with Remote Subnet Mask The remote subnet and subn
28. aphical User Interface GUI on UPnP supported operating systems Windows ME and XP Intuitive web based management interface to simplify operation and support Ethernet connectivity to the Internet or network through a network interface card NIC providing 10 100 Mbps to the port B Firewall that provides many security features such as blocking common hacker attacks including IP Spoofing Ping flood Stealth Scan ICMP flooding etc B Advanced firewall released configuration to extend the capability and security including a virtual server port trigger DMZ host UPnP auto forwarding IP filter and MAC filter Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 1 3 Product Hardware Features B System Interface and Performance e All RJ 45 ports support Auto MDI MDI X Function e Store and forward switching architecture e 8K MAC address table B Power Input e DC 12 48V redundant with a 6 pin removal terminal block e One user programmable alarm relay contact B Operating Temperature e Standard operating temperature models 10 C to 60 C e Extended operating temperature models 35 C to 75 C M Case Installation e P 30 protection metal housing e Grounding Screw for protection e DIN Rail and wall mount design 1 4 Package Contents M 1 APR 3100N series Industrial 802 11 a b g n Access Point VPN Router 2 Reverse SMA connector antennas 1 Product CD 1 Din Rail amp wall mounting bracket with screws
29. appropriate MAC addresses into the MAC fields Click the Save Settings button to save your changes Click the Cancel Changes button to cancel your unsaved changes Click the Close button to return to the previous screen without saving changes 31 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 3 5 WDS ANTAA MEE Setup Wireless Services Security A NAT QoS Administration Status Basic Settings SuperChannel Wireless Security MAC Filter WDS Wireless Distribution System WDS Settings Wireless MAC 7C CB 00 08 10 98 Disable O0 OD Disable Disable Disable Disable Disable Disable Disable Disable SIE 81 8 SE SS SS SI 18118 8 HEISE GE 2 8 8 8 8 8 8 8 8 sj sj e s ls le lelle e 8 00 00 LU 00 LU 00 00 00 QU LU 8 8 8 8 8 18 8 8 8 Disable Extra Options Lazy WDS Enable Disable Default Disable WDS Subnet Enable Disable NAT Disable IP Address D D Subnet Mack Apply Settings Cancel Changes The WDS Wireless Distribution System allows the access point to perform bridging where the access points will only communicate with other WDS access points and associated stations The MAC address of units forming the WDS must be input to the WDS table All units within the WDS must have the MAC addresses of the other associating units MAC addresses input to their WDS list 32 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0
30. ce Antaira Technologies LLC will not be liable for any technical inaccuracies or typographical errors found in this guide Changes are periodically made to the information contained herein and will be incorporated into later versions of the manual The information contained is subject to change without prior notice Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy It may cause harmful interference to radio communications if the equipment is not installed and used in accordance with the instructions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radi
31. collision control management has time interval defined 78 during which all the other stations hold off the transmission and wait until the requesting station will finish transmission opecifies the ACK Timeout Every time the station receives the data frame it sends an ACK frame to the AP if transmission errors are ACK Timeout absent If the station receives no ACK frame from the AP within the set timeout it re sends the frame The performance drops because too many data frames are being re sent thus if the timeout is set too short or too long it will result in a poor connection and throughput performance Network traffic is always unpredictable and the only basic assurance that can be offered is the best effort traffic delivery To overcome this challenge Quality of Service QoS is applied throughout the network QoS This ensures that network traffic is prioritized according to specified Prioritization criteria and receives preferential treatments By traffic prioritization function users can classify the traffic into four classes for differential network application All of Antaira s industrial managed switches support four priority queues System warning function is very important for managing a switch Users can manage the switch by Syslog System Event Log and Email Server through the Services tab for Advanced Notice in any event type dann By setting the remote server the user will receive these system warning featu
32. ddr 7C CB 0D 08 1D 98 Wireless Mode AP T Wireless Network Mode Mixed Y MEM gome om Flom Wireless Channel Auto Wireless Network Name SSID Antaira ath0 Half 10 MHz Wireless SSID Broadcast V Enable Disable Jus Advanced Settings Basic Settings Description Dynamic 20 40 MHz The unit will auto negotiate between 20 or 40 MHz channels for the best possible performance Note Both the AP and Client side need to support the 40 MHz channel Turbo 40 MHz IEEE 802 11a g n offer might offer the option to use 40 MHz for enhanced through put Note Both the AP Channel Width and Client side need to support the 40 MHz channel Full 20 MHz Typical standard that offers stable throughput in environments with more wireless noise Half 10 MHz Reduces the transmit power by 1 2 of the original Quarter 5 MHz Reduces the transmit power by 4 of the original 5 3 1 4 Wireless Channel The default wireless channel is set to auto The user can adjust the wireless channel to select a unique unpopulated channel The user should be aware of and pay attention to the possibility of neighboring channels overlapping All devices on the wireless network must use the same channel in order to function appropriately 26 Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 5 3 1 5 Extension Channel The control channel is the main channel that is being used The extension channel is part of the
33. e device Primary DNS server IP is mandatory It is used by the DNS Proxy and for the device management purpose Secondary DNS server IP address is optional It is used as the fail over in case the primary DNS server will become unresponsive Value Description Port forwarding allows specific ports of the hosts residing in the internal Port network to be forwarded to the external network This is useful for a Forwarding number of applications such as FTP servers gaming etc where different host systems need to be seen using a single common IP address port This is the IP of the host which is connected to the internal network and IP Address needs to be accessible from the external network This is the TCP UDP port of the application running on the host which is Port To connected to the internal network The specified port will be accessible from the external network This is the TCP UDP port of the external port running and is the port seen by users on the internet The specified port will be accessible from the external network Value Description Point to Point Protocol over Ethernet PPPoE is a virtually private and secure connection between two systems which enables encapsulated data transport It is commonly used as the medium for subscribers to connect to Internet Service Providers Select the IP Address option BEBGE PPPoE to configure a PPPoE tunnel in order to connect to an ISP Only the external network interface can be co
34. e industrial Ethernet DIN Rail switch please see Figure 3 1 to learn how to install the DIN Rail on the switch Figure 3 1 The Rear Side of the Switch and DIN Rail Bracket Follow the steps below to learn how to hang the industrial router 1 Use the screws to install the DIN Rail bracket on the rear side of the industrial Ethernet switch To remove the DIN Rail bracket do the opposite from step 1 After the DIN Rail bracket is installed on the rear side of the switch insert the top of the DIN Rail on to the track as shown below in Figure 3 2 Lightly pull down the bracket on to the rail as shown below in Figure 3 3 Check if the bracket is mounted tightly on the rail To remove the industrial Ethernet switch from the rail do the opposite from the above steps Figure 3 2 Figure 3 3 Insert the Switch on the DIN Hai Stable the Switch on DIN Hau Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 3 2 Wall Mounting Follow the steps below to mount the industrial Ethernet switch using the wall mounting bracket as shown below in Figure 3 4 d Remove the DIN Hal bracket from the industrial Ethernet switch by loosening the screws Place the wall mounting bracket flush with the back of the industrial Ethernet switch Use the screws to screw the wall mounting bracket on the industrial Ethernet router Use the hook holes at the edges of the wall mounting bracket to hang the industrial Ethernet switch on th
35. e wall To remove the wall mount bracket do the opposite from the steps above Figure 3 4 Wall Mounting Bracket on the Router 10 Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 4 Hardware Installation 4 1 Installation Steps This section will explain how to install Antaira s APR 3100N series industrial IEEE 802 11a b g n access point VPN router Installation Steps 1 2 Unpack the industrial Ethernet router from the original packing box Check if the DIN Rail bracket is screwed on the industrial Ethernet router e If the DIN Rail is not screwed on the industrial Ethernet router please refer to the DIN Rail Mounting section for DIN Rail installation e f you want to wall mount the industrial Ethernet router please refer to the Wall Mounting section for wall mounting installation To hang the industrial Ethernet router on a DIN Rail or wall please refer to the Mounting Installation section Power on the industrial Ethernet router and then the power LED light will turn on e f you need help on how to wire power please refer to the Wiring the Power Inputs section e Please refer to the LED Indicators section for LED light indication Prepare the twisted pair straight through category 5 cable for Ethernet connection Insert one side of the RJ 45 cable into router s Ethernet port and on the other side into the networking device s Ethernet port e g switch PC or server The Ethernet port s
36. ectar 61 viii Industrial Wireless Ethernet Router APR 3100 Series User Manual V1 0 1 Introduction Antaira Technologies industrial wireless devices come with a pre installed user friendly web console interface which allows users to easily configure and manage units 1 1 Product Overview Antaira s APR 3100N series of wireless routers is designed to operate within industrial environments The router provides a fast and effective means of communicating over a LAN via a wired or wireless connection Multiple WAN connection types are provided for easy access to the internet The APR 3100N series is an 802 11a b g n high performance wireless device Itis capable of data transfer rates up to 300 Mbps It is easy to extend the reach and number of computers connected to your wireless network The APR 3100N wireless router s VPN capability creates encrypted tunnels through the internet allowing a remote office or traveling users to securely connect into the user s corporate network from off site It is a fully manageable industrial Ethernet device that supports the standard Layer 3 Ethernet configurable settings This product series is IP30 rated and DIN rail mountable that provides a standard operating temperature range 10 C to 60 C and an extended operating temperature range 35 C to 75 C 1 2 Product Software Features B Effortless installation via configurable Universal Plug and Play UPnP integration with an intuitive Gr
37. ernet Protocol Security IPSec are protocols used to implement a secure exchange of packets at the IP layer IPSec Passthough Keeping the IPSec enabled allows IPSec tunnels to pass though the router Point to Point Tunneling Protocol PPTP allows a VPN session to a windows NT 4 0 or 2000 server PPTP Passthrough To allow a PPTP tunnel to pass though the router the PPTP passthough will need to be enabled Layer Two Tunneling Protocol L2TP is an extension of the PPP protocol that enables the ISP to operate Virtual Private Networks VPS s The L2TP merges Microsoft and Cisco features to allow L2TP tunnels to pass through the router The settings must be applied and saved before they take effect L2TP Passthrough 40 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 6 Access Restrictions Security Access Restrictions NAT Qu 15 Administration Status 5 6 1 WAN Access WAN Access Access Policy Policy iO 7 Status Enable Disable Policy Name Deny Internet access during selected days and hours Filter Access Policy Allows the user to customize up to 10 different Internet access policies for specific PC s based upon the PC s MAC address Ai s ee Click the Edit list of clients button Enter the appropriate IP and MAC addresses Any changes will List of Clients need to be applied and saved Allows the user to set up specific days or
38. ess Network Mode Mixed Y Channel Width Full 20 MHz Y Wireless Channel Auto T Wireless Network Name SSID Antaira ath0 Wireless SSID Broadcast Enable Disable N Only 24 GHz Advanced Settings dins Mixed see different sections below B Only IEEE 802 11b allows a max data rate of 11 Mbits s through a 2 4 GHz wireless connection If only B type Wireless devices are on the network use this mode G Only IEEE 802 11g allows a max data rate of 54 Mbits s through a 2 4 GHz wireless connection If only G type Wireless devices are on the network use this mode BG Mixed If B amp G type wireless devices are on the network A Only IEEE 802 11a allows a max data rate of 54 Mbits s Wireless Network Mode through a 5 GHz wireless connection If only A type Wireless devices are on the network use this mode NG Mixed Is the 802 11n 2 4 GHz band and represents a mix N Only 2 4 GHz Improved throughput for 2 4 GHz devices that also have the IEEE 802 11n standard NA Mixed Is the 802 11n 5 GHz band that represents a mix of 802 11 and 802 11a N Only 5 GHz Improved throughput for 5 GHz devices that also have the IEEE 802 11n standard 25 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 3 1 3 Channel Width Setup Wireless Services Security A Basic Settings SuperChannel Wireless Security Wireless Physical Interface ath 2 4 GHz 5 GHz Physical Interface ath SSID Antaira ath0 HWA
39. ess Server Settings DHCP DHCP Type DHCP Server DHCP Server Enable Disable Start IP Address 192 168 1 100 Maximum DHCP Users 50 Client Lease Time 1440 min Static DNS 1 D D D 0 Static DNS 2 H D 0 Static DNS 3 0 D 0 WINS D H D 0 Use DNSMasg for DHCP Use DNSMasg for DNS ri DHCP Authoritative wf Network Address Description Server Settings Server Keep the default Enable to keep the DHCP server option lf there is already a DHCP server on the network select Disable DHCP Type Forwarder Additional routers can be hardwired to the main router on the network The additional routers will have the type set as Forwarder Any devices connected to the additional routers will receive their DHCP information from the main router there is already a DHCP server active on the network A numerical value for the DHCP server to start with when Start IP Address assigning IP addresses Note Do NOT start with 192 168 1 1 as the routers IP address 16 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 The maximum number of PCs the router will assign the IP Maximum DHCP Users address to go through the DHCP The Domain Name System DNS is how domain names are Static DNS IP Address translated to Internet addresses The ISP provider will provide at least one unique DNS IP addresses Windows Internet Naming Services Manages the PC s interaction with the internet If a
40. et mask of the network the user is connecting with MPPE Encryption This is used to connect to similar chipset routers If the user is connecting to a windows VPN the user would need mppe required no40no56 stateless User Name The user name that will be seen when connecting to the VPN server OpenVPN Security setting based on certificates that cannot be created on the router Please refer to OpenVPN s online documentation for instruction on creating certificates and configuring OpenVPN 36 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 4 3 USB Services VPH USB Hotspot USB Support USB Support Core USB Support Enable Disable USB Printer Support Enable Disable USB Storage Support Enable Disable Automatic Drive Mount Enable Disable Run on mount Script Name Mount this Partition to jffs UUID Mount this Partition to opt UUID Use SES Button to remove drives Enable Disable Description aa Default is Disabled Select Enable to use USB Support Default is Disabled Select Enable to use Printer Support Default is Disabled Select Enable to use External Devices Automatically mount connected drives Run on mount Script Run script from the specified path wherever a drive is mounted Name though the Automatic Drive Mount Mount this Partition to jiffs SES Button Un mount drives before disconnecting them Mount partition with a UUID
41. etwork RAD LL WEP should only be used when required due to lower security The user can choose either 64 bit or 128 bit For 64 bit the passphrase must be 10 hexadecimal characters For 128 bit the passphrase must be 26 hexadecimal characters Note Hexadecimal characters are 0 9 and A F 30 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 3 4 MAC Filter ANTAII CONTROL PANEL Setup Wireless Services Security Access Restrictions NAT QoS Administration Status Basic Settings SuperChannel Wireless Security MAC Filter WDS Wireless MAC Filter ath MAC Filter Use Filter Enable Disable Filter Mode Prevent clients listed from accessing the wireless network Permit only clients listed to access the wireless network Edit MAC Filter List Apply Settings Cancel Changes The user can set up a wireless MAC filter The MAC address filter on the APR 3100N can be set to either Allow the MAC addresses listed to gain access or the list can be set to Deny access by the listed MAC addresses If you want to block specific wireless equipped PCs from communicating with the router keep the default setting Prevent PCs listed from accessing the wireless network If you want to allow specific wireless equipped PCs to communicate with the router click the radio button next to Permit only PCs listed to access the wireless network Click the Edit MAC Filter List button Enter the
42. ing UPnP DMZ QoS Universal Plug and Play is a set of computer network protocols This technology is for the automatic configuration of devices The UPnP is able to seamlessly integrate connected devices through control protocols built upon open communication standards Universal Plug and Play UPnP Forwards P Lee ee Fi e EI TENTER Te IE TTL TIN Fi m um scription Enabled From WAM To LAN IP Address UPnP Configuration UPnP Service Enable Disable Clear port forwards at startup Enabla Disable Description The forwards table shows all open ports forwarded automatically by the UPnP Forwards can be individually deleted with the trash can or the Delete All will clear all forwards UPnP Service Allows applications to automatically setup port forwarding Clear Port Forwards at If enabled all UPnP port forwardings are deleted when the Startup router starts up 46 Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 5 7 5 DMZ Setup Wireless Services Security Access Restrictions NAT QoS E Li Administration Port Forwarding Port Range Forwarding Port Triggering UPnP DMZ Qos The DeMilitarized Zone DMZ feature allows one local user the exposure to the internet for services such as video conferencing The DMZ hosting forwards all of the ports at the same time to one PC Demilitarized Zone DMZ DMZ Use DMZ Enable 9 Disable DM Host IP Address 192 168 1 o En
43. ion Restore Settings Please select a file to restore Choose File No file chosen By pressing the Backup button the user will automatically Backup Settings download a bin file of the current configuration settings on the router The user can upload a currently saved configuration file by pressing the Choose File button then selecting the correct file Restore Configuration from the network Note Only restore files that are based on the same firmware version and correct router models 55 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 9 Status GINTLOIFA CONTROL PANEL Wir Services Security iccess Restrictions NAT Qos Administration Status LAN Wireless Bandwidth Sys Info The status page will display the routers current status and configuration settings The status pages will be for review purposes only the user will not be able to make changes to any of the sections within the Status section 5 9 1 Router Router Information System Router Name Antaira Router Model Industrial Router Firmware Version Antaira 1 1 10 01 14 std build 21995M Kernel Version Linux 3 10 49 172 Wed Oct 1 21 43 15 CEST 2014 mips MAC Address ZC CB D0D 08 1D 98 Hostname WAN Domain Name LAN Domain Mame Current Time Not available Uptime 34 min CPU CPU Madel Atheros AR7241 rev 1 1 0x0101 CPU Cores 1 CPU Clock 400 MHz Load Average 0 23 0 13 0 07 Memory Total Available 61720 kB
44. ion Status Basic Setup DDNS MAC Address Clone Advanced Routing Networking EoIP Tunnel 5 2 1 1 WAN Setup Automatic Configuration DHCP WAN Connection Type dich SS PFTP Connection Type Automatic Configuration DHCP Y L2TP Heartbeat Signal Mobile Broadband WAN Connection Type Disabled Description The WAN port is disabled A static IP address will be used Required IP address subnet mask gateway and server to be entered manually The router obtains its WAN side IP address from a DHCP server Automatic Configuration DHCP Configure as a PPPoE Client Username and Password are required Advanced Options Service Name T Home VLAN 7 Support PPP Compression MPPE Encryption Single Line Multi Link and Connection Strategy Allows the users to set multiple paths of the WAN Used in PPPoE Dual Russia Establishes a connection via PPTP Required Gateway Username Password and encryption information Establishes a connection via L2TP Required Gateway Username Password and encryption information Short frames sent by the wireless device that contain information such as the SSID encryption information data rates HeartBeat Signal l l ol mE l and other information This information is only used if the ISP supports heartbeat signals Note that HeartBeat signals are 14 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 only used in Australia Mobi
45. le Broadband Used for LTE cellular routers Enter the username and password used when logging onto the Username Password ISP through a PPPoE or PPTP connection Used for different types of speeds and service providers AT amp T uses 99 1 UMTS 3G 3 5G Verizon uses 99 3 UMTS 3G 3 5G Access Point Name is the name of a gateway between a GPRS 3G or 4G mobile network and another computer network typically the internet For AT amp T version units use broadband as the APN For Verizon version units use vzwinternet as the APN 5 2 1 2 Optional Settings Optional Settings Router Name Antaira Hostname Domain Mame MTU Auto Y 1500 STP Enable Disable Description een Ress re SPs and ane provi HATS Necessary for some ISP s and can be provided by the ISP Maximum Transmission Unit Specifics the largest packet size vn permitted for Internet transmission Auto will allow the router to select the best MTU for the Internet connection Manual values entered should be in the 1200 to 1500 range devices without creating loops 15 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 2 1 3 Router IP Router IP Local IP Address 192 168 1 1 Subnet Mask 255 255 255 0 Gateway D D 0 0 Local DNS Ol D Di 0 Choose the desired LAN side IP Address Subnet Mask Gateway and Local DNS information 5 2 1 4 Network Address Server Settings DHCP Network Addr
46. llowing models e APR 3100N This document is the current official release manual Please check our website www antaira com for any updated manual or contact us by e mail support antaira com Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 Table of Contents T IntFOdU GOD ressens semaines 1 1 1 Product Overview 1 1 2 Product Software Features 1 1 3 Product Hardware Features 2 1 4 Package Contents 2 1 5 Safety DT ue D 2 2 Hardware Description 3 2 1 Physical Dimensions 3 CAE FONRO a 4 25 GEN 4 2 4 LED Indicators D 2 9 ENESTE POMS era itunes 6 OO ee an ete TU T 7 2 7 Wiring the Power Inputs 7 2 8 Wiring the Fault Alarm Contact 8 3 Mounting Installation 9 3 1 DIN Rail Mounting 9 9 2 Vall MOUNIIG ao 10 4 Hardware Installation 11 4 1 Installatlol Sie DS een 11 5 Web Management eres 12 5 1 Web Console Configuration 12 5 1 1 About Web Based Management 12 Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0
47. ms to the following product standards This device complies with the Electromagnetic Compatibility Directive 89 336 EEC issued by the Commission of the European Community Compliance with this directive implies conformity to the following European Norms in brackets are the equivalent international standards Electromagnetic Interference Conduction and Radiation EN 55022 CISPR 22 Electromagnetic Immunity EN 55024 IEC61000 4 2 3 4 5 6 8 11 Low Voltage Directive EN 60 950 1992 A1 1993 A2 1993 A3 1995 A4 1996 A11 1997 Therefore this product is in conformity with the following regional standards FCC Class B following the provisions of FCC Part 15 directive CE Mark following the provisions of the EC directive Antaira also declares that The wireless card in this product complies with the R amp TTE Directive 1999 5 EC issued by the Commission of the European Community Compliance with this directive implies conformity to the following e EMC Standards FCC 47 CFR Part 15 Subpart B 47 CFR Part 15 Subpart C Section 15 247 CE EN 300 328 2 EN 300 826 EN 301 489 17 Therefore this product is in conformity with the following regional standards FCC Class B following the provisions of FCC Part 15 directive CE Mark following the provisions of the EC directive Industrial Wireless Router Antaira s Industrial Wireless Ethernet Router User Manual Version 1 0 November 2014 This manual supports the fo
48. n an external site The number represents how often in days an update will be Force Update Interval performed Any changes made will need to be both applied and saved Apply Settings amp Save before they take effect 5 2 3 MAC Address Clone ANTAII conro Pae Setup Wireless Services Security Access Restrictions NAT Qo5 Administration Status Basic Setup DDNS MAC Address Clone Advanced Routing Networking EoIP Tunnel MAC Address Clone MAC Clone Enable Disable Apply Settings Cancel Changes By enabling the MAC address clone the user is able to clone the MAC address of the network adapter onto the router 5 2 3 1 Enable MAC Address Clone ANTAII Setup Wireless CONTROL PANEL Security Access Restrictions NAT QoS Administration Basic Setup DDNS MAC Address Clone Advanced Routing Networking EoIP Tunnel MAC Address Clone MAC Clone Enable Disable Clone WAN MAC Get Current PC MAC Address Clone Wireless MAC Apply Settings Cancel Changes Enter the MAC address of the network adapter in the Clone WAN MAC section or click the Get Current PC MAC Address to fill in the MAC address of the PC currently connected Get Current PC MAC is typically used when establishing a service with certain ISP providers 19 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 2 4 Advance Routing 5 2 4 1 Gateway elegeilee CONTROL PANEL curity Access Restrictions N
49. nfigured as PPPoE client as all the traffic will be sent via this tunnel The IP address Default gateway IP and DNS server IP address will be obtained from the PPPoE server after PPPoE connection is established Broadcast address is used for the PPPoE server discovery and tunnel establishment Valid authorization 62 Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 credentials are required for the PPPoE connection PPPoE Username to connect to the server must match the configured on Username the PPPoE server Password to connect to the server must match the configured on the Password PPPOE server The size in bytes of the Maximum Transmission Unit MTU and MTU MRU Maximum Receive Unit MRU used for the data encapsulation while transferring it through the PPP tunnel The Demilitarized zone DMZ can be enabled and used as a place where services can be placed such as Web Servers Proxy Servers and E mail Servers such that these services can still serve the local network Enable DMZ and are at the same time isolated from it for additional security DMZ is commonly used with the NAT functionality as an alternative for the Port Forwarding while makes all the ports of the host network device be visible from the external network side Connected to the internal network host specified with the DMZ IP address will be accessible from the external network With a multicast design applications can send one copy
50. ng Create Bridge Bridge 0 bi STP Off Prio 32768 MTU 1500 Add Creates a new empty network bridge for later use Spanning Tree Protocol on or off Pie 7 Sets the bridge priority order Lower number is higher priority Assign to Bridge Assignment 0 Interface eth Prio 63 nane Add Allows the user to assign an Interface to a network bridge as well as set a priority level Current Bridging Table A table with all of the current bridges and their components can be seen in the Bridging section of the networking tab as shown above 21 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 2 5 3 Bonding Bonding balance rr Y Bonding active backup i balance xor ima T SP Bonding Type balance rr Bonding Interfaces 1 ment ue Bonding 0 Interface Bond bondO T Slave erh PSGE 802 3ad de Delete balance tlb balance alb ghted rr duplex Packet transmission in sequential order from the first available Balance rr slave to the last This provides load balancing and fault tolerance Only one slave in the bond is active Another slave can only Active Backup mE become active if the current slave fails Transmission is based on the source MAC address xor ed with Balance xor mE the destination MAC address Broadcast Transmits all information on to all slave devices IEEE 802 3ad LACP creates aggregation groups based on 802 3ad similar speeds and duplex
51. ngs Description Wireless Mode AP The default setting Access point mode will allow the router to act as a connection point for wireless client devices to connect with Client The client mode is used to connect to with an access point Client Bridge Routed The radio interface is used to connect the LAN side of the router to a remote Access Point The LAN and the remote AP will be in the same subnet This is called a bridge between two network segments The WAN side of the router is unused and can be disabled Use this mode e g to make the router act as a WLAN adapter for a device connected to one of its LAN Ethernet ports Adhoc Is a peer to peer point to point communication that does not use access points Devices in Adhoc mode communicate directly to each other WDS Station Is a proprietary connection with the WDS AP The WDS Station is like a client although multiple layer 2 devices can be connected to the WDS Station device WDS AP Proprietary access point mode that WDS Station devices can connect with 24 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 3 1 2 Wireless Network Mode Setup Wireless Services Security Access Restrictions NAT Qo5 Admi Basic Settings SuperChannel Wireless Security MAC Filter WDS Wireless Physical Interface ath 2 4 GHz 5 GHz Physical Interface ath0 SSID Antaira ath0 HWAddr 7C CB 0D 08 1D 98 Wireless Mode AP Y Wirel
52. nnel Wireless Security MAC Filter WDS Wireless Security ath Physical Interface ath SSID Antaira mktg HWAddr 7C CB 0D 08 1D 98 WPA Personal WPA Enterprise Security Mode Disabled Y WPA Personal WPA Enterprise WPA2 Personal Mixed WPA Enterprise Mixed y Settings RADIUS ES ETS Pe Wireless Security Description If wireless security has been disabled anyone can log onto the Disabled access point Choose between AES or TKIP security and enter a password WPA Personal between 8 and 63 characters The Group Key Renewal can be between 0 and 99 999 seconds Uses an external RADIUS server to preform authentication Use WPA Enterprise the IP address of the RADIUS server the RADIUS port default is 1812 and the shared secret from the RADIUS server WPA2 provides additional security from WPA by using the IEEE WPA2 Personal 802 11i protocols AES is required when using WPA2 WPA2 with TKIP is not supported Uses an external RADIUS server to preform authentication Use WPA2 Enterprise the IP address of the RADIUS server the RADIUS port default is 1812 and the shared secret from the RADIUS server If there is a mixture of client devices that use WPA2 and WPA WPA2 Personal Mixed security Personal is typically used for small networks ex home If there is a mixture of client devices that use WPA2 and WPA WPA2 Enterprise Mixed security Enterprise mode uses a RADIUS server allowing access to be controlled in a large n
53. o TV technician for help Caution Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation CE Mark Warning This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures RF Exposure Warning The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment The equipment must not be co located or operating in conjunction with any other antenna or transmitter ICES 003 Statement This Class B digital apparatus complies with Canadian ICES 003 Industry Canada Statement This device complies with RSS 210 of the Industry Canada Rules Operation is subject the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 Declaration of Conformity Antaira declares the following Product Type Wireless Industrial Router Model No APR 3100N confor
54. oIP Tunnel Ethernet Over IP Tunneling Tunnel 1 EolP Tunnel Enable O Disable Remote IP Address 192 168 90 1 Bridging Enable Disable Tunnel 2 EoIP Tunnel Enable Disable The APR 3100N series supports up to 10 Ethernet over IP Tunnels EoIP allows the user to create a tunnel between two routers in addition to an IP connection The EolP connection is available when the bridging function of the router is enabled The user can create tunnels over the Internet through encrypted tunnels or over 802 11b ad hock wireless networks All changes must be applied and saved before they take effect 23 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 3 Wireless 5 3 1 Basic Settings All the basic wireless settings can be configured in this page Operators can change the Wireless Mode Network Mode Channel Width Wireless Channel and SSID 5 3 1 1 Wireless Mode GI Y CO CONTROL PANEL Setup Wireless Services Security Access Restrictions Administration Basic Settings SuperChannel Wireless Security MAC Filter Wireless Physical Interface ath0 2 4 GHz 5 GHz Physical Interface ath0 SSID Antaira ath0 HWAddr 7C CB 0D 08 1D 98 Wireless Mode Wireless Network Mode Channel Width Wireless Channel Wireless Network Name SSID Wireless SSID Broadcast Advanced Settings AP v Mixed v Full 20 MHz Y acu Bridge Routed Auto v E m Antaira ath0 Enable Disable Basic Setti
55. opdown menu of available services The user will select the specific service that prioritization is desired on How high of a priority the user would like to set for specific SEHR services Netmask Priority Default Bandwidth Level Enable Per User Default Limits WAN Bandwidth in kbits Up 100000 WAN Bandwidth in kbits Down 100000 LAN Bandwidth in kbits 100000 QoS Priority Continued Description The netmask is the number of bits of the IP address to match Netmask Priority The user can enter a netmask as 32 if the user puts 0 it will mean all IP s To prioritize devices based on MAC address rather than IP MAC Priority address the user can Add the MAC address of any specific device Default Bandwidth l T By enabling the user can set up down speeds in Kbits eve 49 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 8 Administration Setup Wireless Services Security A NAT 005 Administration Status p i EL Management Keep Alive Commands WOL Factory Defaults Firmware Upgrade Backup 5 8 1 Management The management screen allows the user to change routers settings as detailed below Router Password Router Username ETTE TETT Router Password ETTE TT TETT Re enter to confirm Too eee TT TETT Default is root The user is suggested to change the routers Router Username name Default is admin The user is suggested to change the routers Router
56. outer APR 3100N Series User Manual V1 0 2 4 LED Indicators There are LED light indicators located on the front panel of the industrial access point VPN router that display the power status and network status Each LED indicator has a different color and has its own specific meaning Table 2 1 Powerinput1is active Powerinput1isinactive Powerinput2is active Powerinput2isinactive ME No Power going into PWR1 E Power detected going into PWR1 No Power going into PWR2 E NE Power detected going into PWR2 FN Unit not ready Boot sequence LED 1 25 Off Uni is ready SCH LED 75 FX LED 4 10096 Connected to network 10 100Mbps LAN Port 1 amp 2 P iie Networking is active Not connected to network Table 2 1 LED Indicators for APR 3100N Series Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 2 5 Ethernet Ports ul RJ 45 Ports RJ 45 Ports Auto MDI MDIX The RJ 45 ports are auto sensing for 10Base T and 100Base Tx connections Auto MDI MDIX means that the switch can connect to another switch or workstation without changing the straight through or crossover cabling See the figures below for the straight through and crossover cabling schematics E RJ 45 Pin Assignments Table 2 2 Not used Table 2 2 RJ45 Pin Assignments BE PANEM M NENNEN LE KJE Note and signs represent the polarity of the wires that make up each wire pair
57. re 5 1 Web Console Login 4 Keyin the default username root and password admin 12 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 Click the Login button then the main status page of the web console will appear ms O 192 168 1 1 antaira Firmware Antaira 1 1 10 01 14 s Time 00 08 51 up 9 min load average 0 2 CONTROL PANEL Setup Wireless Services Security Access Restrictions Administration Status System Information Router Services Router Name Antaira DHCP Server Disabled Router Model Industrial Router WRT radauth Disabled LAN MAC USB Support Disabled WAM MAC Wireless MAC menny WAN IP 0 0 0 0 Total Available 60 3 MB 64 0 MB LAN IP 192 158 1 1 Free 43 8 MB 60 3 MB Used 16 4 MB 60 3 MB Wireless Buffers 2 2 MB 16 4 MB Radio Radio is On Cached 5 6 MB 16 4 MB Mode AP Active 4 2 MB 16 4 MB Network Mixed Inactive 5 1 MB 16 4 MB SSID Antaira athO Channel 11 2462 MHz apace sage TX Power 20 dem NYRAM 18 66 KB 64 KB Figure 5 2 The online image of the switch will display the real time ports connection status 13 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 2 Setup 5 2 1 Basic Setup Firmware Antaira 1 1 10 01 14 std m i 1 m ime 00 23 05 up 23 min loai average 0 05 0 05 0 0 eie weiae CONTROL PANEL bly ts ede cites ee Setu P Wireless Services Security Access Restrictions NAT Qo5 Administrat
58. res through email whenever any event occurs It definitely increases the flexibility and capability for the user to monitor the remote site network and device statuses Antaira Customer Service and Support Antaira US Headquarter 844 268 2472 Antaira Europe Office 48 22 862 88 81 Antaira Asia Office 886 2 2218 9733 Please report any problems to Antaira www antaira com support antaira com www antaira eu info antaira eu www antaira com tw info antaira com tw 64
59. settings Note Connected switches need to support the LACP Transmit Load Balancing that does not require any special switch support Outgoing traffic is distributed based on the Balance tlb m current load of each slave If a slave unit fails to receive traffic another slave will then take over the traffic from the failed slave Adaptive Load Balancing is for IPV4 traffic and does not require special switch settings Load balancing is performed though ARP negotiation Bonding drivers intercept the ARP replies Balance alb from the loacal system and overwrites the source hardware address with the unique hardware address of the slaves in the bond Creating different hardware addresses for different peers to the server Round Robin bonding will use weights assigned to specific slaves Each slave will have a assigned weight through ioctl The values will be used at the start of each cycle Each slave Weighted rr will have a token counter restored to its s weight The tokens are then used to purchase emitted frames When there are no tokens available then a new cycle begins Duplex Full duplex connections of dedicated send and receive links 22 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 2 6 EoIP Tunnel c avenae conrrot panel Setup Wireless Services Security Access Restrictions NAT QoS Administration Status Basic Setup DDNS MAC Address Clone Advanced Routing Networking E
60. ss Ethernet Router APHR 3100N Series User Manual V1 0 5 7 NAT QoS caue Setup Wireless Services Security Access Restrictions NAT QoS Administration Status CONTROL PANEL Port Forwarding Port Range Forwarding Port Triggering UPnP DMZ Qos 5 7 1 Port Forwarding Port Forwarding Forwards vg Port Forwarding allows the user to set up public services on the network such as web servers ftp servers and e mail servers Specialized Internet applications are any applications that use Internet access to perform functions such as video conferencing or online gaming To add a new port forwarding rule click add and fill in the fields listed below Forwards Both 0 0 0 0 0 0 Port Forwarding Description Application Enter the name of the application The user will need to select the correct protocol based on their Protocol specific application The choices are TCP UDP or both Source Net Forwarded only if the sender matches this IP net The number of the external port port number seen by users on the Internet side IP Address The IP address of the PC running the application The number of the internal port port number used by the Port To mE application Enable Check to enable port forwarding for the application The settings must be applied and saved before they take effect 43 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 7 2 Port
61. times that the listed Days amp Times PCs will be blocked from internet access List of clients Enter MAC Address of the clients in this format xx xx xx xx xx xx MAC 01 O0 00 00 00 00 00 MAC 02 O0 00 000 00 00 00 MAC 03 O0 00 00 00 00 00 MAC 04 O0 00 00 00 00 00 MAC 05 O0 00 00 00 00 00 MAC 06 QOO0 00 00 00 00 00 MAC OF COO zODz 00 00 00 00 MAC 08 O0 00 00 00 00 00 Enter the IP Address of the clients IP 01 192 168 1 IP 02 192 168 1 0 IF 03 192 168 1 0 IF 04 192 168 1 0 IF 05 192 168 1 a IP 06 192 168 1 Enter the IP Range of the clients IP Range 01 D UR D Or D 0 0 IP Range 02 Ol DI Oy Dies a a 0 Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 Blocked Services Catch all P2P Protocols Mone T Mone T Mone T Mone T Add Edit Service aimwebcontent applejuice ares armagetron audiogalaxy battlefield1942 battlefield2 battlefield2142 Blocked Services The user can choose to block access to certain internet services through a dropdown menu under the Catch all P2P Protocols Website Blocking by URL Address Website Blocking by Keyword URL Blocking Keyword The user can input specific URL addresses to deny access to those websites The user can input specific keywords to block access to websites with these keywords in their webpage The settings must be applied and saved before they take effect 42 Industrial Wirele
62. unit needs to be reset back to the factory default settings the user can select YES for the Restore Factory Defaults section To finalize the changes Be sure to press the Apply Settings button Note After resetting to factory defaults all previous saved settings will be lost and the unit will return to the original settings IP Address 192 168 1 1 IP Username root Password admin 5 8 6 Firmware Upgrade Setup Wireless Services Security CCE NAT QoS Administration Management Keep Alive Commands Factory Defaults Firmware Upgrade Firmware Management Firmware Upgrade After flashing reset to Dont reset Please select a file to upgrade Choose File No file chosen When new firmware releases are available they will be posted on www antaira com Typically if the router is not experiencing any issues there is no need to load new firmware unless new features are implemented and the upgrade is available Note When new firmware is loaded the previous configuration settings will be lost Please make notes of the settings that are being used so the upgrade process is as easy as possible 54 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 8 7 Backup Setup Wireless Services Security Access Restrictions MAT Qos Administration Status Management Keep Alive Commands WOL Factory Defaults Firmware Upgrade Backup Backup Configuration Backup Settings Restore Configurat
63. ve 5 5 MB 38 4 MB SSID Antaira mktg Channel 1 2412 MHz Spanne aage TX Power 20 dBm NV RAM 18 97 KB 64 KB Rate 300 Mb s GPS Info Wireless Packet Info m Received RX 49542 OK no error Longitude Transmitted TX 178160 OK no error Latitude Longitude N A Latitude N A Altitude Visible Satelites Map Link M A Wireless Clients MAC Address XXIXXIXXIXXIAE BB5 atho 117M 130M 60 Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 6 Terms Terms Value Description DHCP Client Enable the DHCP client by checking this box If DHCP fails and the configured IP address is zero DHCP will retry If DHCP fails and the configured IP address is not a zero DHCP will stop and the configured IP settings will be used The DHCP client will announce the configured System Name as hostname to provide DNS lookup IP Address The unit default IP is 192 168 1 254 Assign the IP address that the network is using If the DHCP client function is enabled the user is not required to assign the IP address The network DHCP server will assign the IP address for the switch and it will be displayed in this column Choose this option to assign the static IP settings for the external interface IP Address and Netmask settings should consist with the address space of the network segment where the device resides If the device IP settings and administrator PC which is connected to the device through wired or wireless
64. ve the stability of the router Maximum Ports 4096 TCP Timeout 120 sec UDP Timeout 120 sec IP Filter Settings 5 8 2 Keep Alive Keep Alive Proxy Connection Watchdog Enable Proxy Watchdog Enable Disable Schedule Reboot Schedule Reboot Enable Disable WDS Connection Watchdog Enable Watchdog Enable Disable Keep Alive Description The Proxy Connection watchdog will attempt to access a proxy Proxy Connection and reboot if it cannot connect The user will need to input the Watchdog IP address of the Proxy as well as the time interval The user can schedule reboots for the router based on either a Schedule Reboot EE 8 time interval or at a set time on specific days The user is able to Enable the WDS Connection Watchdog WDS Connection The user can then input a time interval check Seconds The Watchdog final step is inputting the IP address of an internet server Ex Google is 8 8 8 8 52 Industrial Wireless Ethernet Router APR 3100N Series User Manual V1 0 5 8 3 Commands The user is able to run commands lines directly in the web interface Setup Wireless Services Security Access Restrictions NAT QoS Administration Management Keep Alive Commands Factory Defaults Firmware Upgrade Backup i Diagnostics Command Shell Commands Save Startup Save Shutdown Save Firewall Save Custom Script Command Shell Fill the text area with the command Run Commands to input The
65. work GPS The user can enable GPS coordinate systems The information will be sent to a specific port Default is 2947 the user will then need to use a program such Telnet and Google Earth to do the tracking of the GPS coordinate system This feature is available for LTE cellular models only PPPoE Relay Will allow the DHCP to duplicate the WAN s IP address from the ISP SES AOSS EZ SETUP WPS Button The Reset Button under the Administration gt Management section must be enabled Secure Shell Enabling SSH allows the user to access the router with a SSH client SSH Port number for SSH default is 22 System Log Enable the system log to capture system messages By default they will be collected in the local file var log messages To send the messages to a different system the user can input the IP address of a remote system log server Telnet Enable a telnet server to connect to the router with telnet Default username root password password WAN Traffic Counter The user can view the traffic going through the router The feature can be disabled The save router CPU usage the user can view the traffic though SNMP monitoring on a computer 34 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 4 2 VPN Services Security Access Restrictions MAT QoS Administration Hotspot PPTP Server PPTP Server PPTP Server PPTP Client PPTP Client PPTP Client Options Disable OpenVPN Server D
66. zabled Status LAN Description LAN Status The current LAN setting that is in effect on the router A list of devices connected to the router including their IP and Active Clients MAC addresses 57 Industrial Wireless Ethernet Router APHR 3100N Series User Manual V1 0 5 9 3 Wireless This status screen shows all of the current wireless statuses and configuration settings Please note that within the Status tab all information is read only Changes are made under the standard tabs not the Status overview tabs Wireless Wireless Status MAC Address Radio Mode Hetwork SSID Channel TX Power Rate ACK Timing Encryption Interface atb Wireless Packet Info Received RX Transmitted TX Wireless Nodes Clients C4 85 08 F6 AE 55 ath0 1 18 36 ZC CB 0D 08 1D 98 Radio is On AP Mixed Antaira mktg 1 2412 MHz 20 dBm 300 Mb s 1545 2250m Enabled WPA Personal 19425 OK no error 100 71792 OK mo error 100 sm 6M a 95 5 SN Status Wireless Description Wireless Status Wireless Packet Info The current wireless settings on the device such as the frequency SSID Data Rate and radio mode How much wireless data has been sent and received through the wireless unit as well as any errors that have been detected Information of the wireless clients that are connected to the unit 58 Industrial Wireless Ethernet Router APHR 3100N Series User Manual

APR-3100N Series

Contents

Download Pdf Manuals

Related Search

Related Contents