wiSTAR Key Card Switch Install Instructions
Contents
1. Installation Guide COD Models WIS KCS Hubbell Building Automation ae Key Card Switch enocean a a a F oas Dimensions 4 72 H x 3 81 W x 43 D at edge A 120 mm x 97 mm x 11 mm A Weight 3 5 oz 99 g Environment Indoor use only 472 32 to 131 F 0 to 55 C 120mm e 5 to 95 relative humidity non condensing Agency Compliance FCC IC 381 Take a moment to prepare and ensure optimal communications v with other system components and for user convenience Pick a location near the door where occupants enter and exit Package Contents Tools Required using the key card A common location is on the wall oppo Key Card Switch Power drill 3 16 bit site the door hinges 3 ft 92 cm from the door jamb Trim plate Screwdriver Consider the construction materials in the space and ob 2 screws 2 wall anchors Leveling tool stacles that may interfere with RF signals e e amp s Product Description Installin estimated time 10 minutes He N The Key Card Switch saves energy by signally HVAC lighting and electrical loads that a room is unoccupied It communicates wirelessly with compatible devices in a guest room when a key card is inserted or removed from the slot 1 Decide where you want to mount the key card switch The ideal height is in line with wall switches 49 or 125 cm on center for comfortable access The Key Card Switch can be mounted on most surfaces using the mount2. ed device Check for environment or range issues does not respond Verify the device is linked to wireless mes Check the transceiver connection and the wir sages ing for errors Check if appropriate devices are linked accord ing to good system planning C 902 MHz FCC SZV PTM33XU IC 5713A PTM33XU This device complies with part 15 of the FCC rules and Industry Canada ICES 003 Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IMPORTANT Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lec trique subi meme si le brouillage est susceptible d en compromettre le fonctionnement IMPORTANT Tous les changements ou modifications pas express ment approuv s par la partie responsable de la conformit ont pu vider l autorit de l utilisateur pour actioner cet equipment Limited Warranty ONE YEAR Page 2
3. ing plate or over an existing wall box NOTE If installing over an existing Features Include wall box make sure any bare l electrical wires are capped Determines occupancy based on guest room key card being PP inserted or removed 2 Remove the trim plate from the Harvests kinetic energy from the card action no batteries key card assembly 3 Using a level and a pencil lightly l mark two small dots to align the Transmits room occupancy status wirelessly to other energy upper edge of the key card switch Saving devices in the room Installs easily in new or existing rooms no wiring 4 Mount the key card switch securely to the wall using the Enables other devices to minimize energy use whenever the provided screws and wall anchors room is unoccupied l l A Using the pencil marks to Specifications ensure it s level mark the two mounting screw drill points Power Supply Mechanical energy harvesting power is generated by the motion of key card moving in and out B Drill two holes for the wall an chors with a 3 16 drill bit and insert the wall anchors Transmission Range 80 ft 25 m C Insert the top screw loosely and RF Communications EnOcean 902 MHz level the Key Card Switch EEP EnOcean F6 04 01 Equipment Profile Card Slot Size 4 72 H x 3 8 W x 0 43 D at edge Hotel Standard 120mm x 97mm x 11mm D Insert the bottom screw and then hand tighten the t
4. op screw 2013 Hubbell Building Automation www hubbell automation com Page 1 Key Card Switch e Installation Guide 5 Insert the trim plate tabs into the bottom slots of the key card switch and then lightly flex the trim plate to insert the top tabs TIP To remove the trim plate without marking it press down with a fingernail in the top groove to ease the tabs out of the slots 6 Insert a key card to test the mechanism TIP There should be an audible click each time the key card is inserted or removed Two or more compatible devices can be linked and configured to provide the desired control There are two basic types of devices in the system transmitters and transceivers Transmit only Transmitters are simple energy harvesting devices that send RF messages to communicate a condition level or state Transmitters can only be linked to transceivers Examples gt Self powered Light Switches Occupancy Sensors Transmit amp Receive Transceivers are controlling devices that send as well as receive RF messages They also process relevant control logic and actuate the appropriate outputs switching a light on or off for example Transceivers can be linked with transmitters as well as other transceivers A trans ceiver can have up to 30 devices linked to it Examples gt Relays Gateways The Key Card Switch is a Transmit only Devices To link the Key Card Switch to a transceiver the transceiver m
5. ust first be powered within wireless range of the sensor and set to accepts links To Link or Unlink a Key Card Switch 1 Set the desired transceiver to the desired Link Unlink mode refer to receiving device s installation guide 2 Insert and remove a key card three times quickly there should be an audible click each time gt The Key Card Switch is now linked Refer to the Linking section of the transceiver controller instal lation guides to verify the linking process Typical Interactions The key card interaction depends on the type of transceiver it is linked to for example Linked to a Thermostat or HVAC Controller Insert key card normal mode is activated Remove key card setback mode is activated 2013 Hubbell Building Automation www hubbell automation com Linked to a Load Controller Insert key card a wireless message is sent to close the cir cuits and turn on all linked loads according to user defined program settings Remove key card a wireless message is sent to open the circuits and turn off all linked loads NOTE For multiple installations e g front and back doors all key cards must be removed to send a message Troubleshooting Problem Solution Checklist The key card switch Verify there is an audible click when card is does not generate a inserted or removed message Verify slot is clear of foreign material or debris Use forced air to clean The link
Download Pdf Manuals
Related Search